| 1 | # |
| 2 | # PCCARD (PCMCIA/CardBus) bus subsystem configuration |
| 3 | # |
| 4 | |
| 5 | menuconfig PCCARD |
| 6 | tristate "PCCard (PCMCIA/CardBus) support" |
| 7 | depends on HOTPLUG |
| 8 | ---help--- |
| 9 | Say Y here if you want to attach PCMCIA- or PC-cards to your Linux |
| 10 | computer. These are credit-card size devices such as network cards, |
| 11 | modems or hard drives often used with laptops computers. There are |
| 12 | actually two varieties of these cards: 16 bit PCMCIA and 32 bit |
| 13 | CardBus cards. |
| 14 | |
| 15 | To compile this driver as modules, choose M here: the |
| 16 | module will be called pcmcia_core. |
| 17 | |
| 18 | if PCCARD |
| 19 | |
| 20 | config PCMCIA |
| 21 | tristate "16-bit PCMCIA support" |
| 22 | select CRC32 |
| 23 | default y |
| 24 | ---help--- |
| 25 | This option enables support for 16-bit PCMCIA cards. Most older |
| 26 | PC-cards are such 16-bit PCMCIA cards, so unless you know you're |
| 27 | only using 32-bit CardBus cards, say Y or M here. |
| 28 | |
| 29 | To use 16-bit PCMCIA cards, you will need supporting software in |
| 30 | most cases. (see the file <file:Documentation/Changes> for |
| 31 | location and details). |
| 32 | |
| 33 | To compile this driver as modules, choose M here: the |
| 34 | module will be called pcmcia. |
| 35 | |
| 36 | If unsure, say Y. |
| 37 | |
| 38 | config PCMCIA_LOAD_CIS |
| 39 | bool "Load CIS updates from userspace" |
| 40 | depends on PCMCIA |
| 41 | select FW_LOADER |
| 42 | default y |
| 43 | help |
| 44 | Some PCMCIA cards require an updated Card Information Structure (CIS) |
| 45 | to be loaded from userspace to work correctly. If you say Y here, |
| 46 | and your userspace is arranged correctly, this will be loaded |
| 47 | automatically using the in-kernel firmware loader and the hotplug |
| 48 | subsystem, instead of relying on cardmgr from pcmcia-cs to do so. |
| 49 | |
| 50 | If unsure, say Y. |
| 51 | |
| 52 | config CARDBUS |
| 53 | bool "32-bit CardBus support" |
| 54 | depends on PCI |
| 55 | default y |
| 56 | ---help--- |
| 57 | CardBus is a bus mastering architecture for PC-cards, which allows |
| 58 | for 32 bit PC-cards (the original PCMCIA standard specifies only |
| 59 | a 16 bit wide bus). Many newer PC-cards are actually CardBus cards. |
| 60 | |
| 61 | To use 32 bit PC-cards, you also need a CardBus compatible host |
| 62 | bridge. Virtually all modern PCMCIA bridges do this, and most of |
| 63 | them are "yenta-compatible", so say Y or M there, too. |
| 64 | |
| 65 | If unsure, say Y. |
| 66 | |
| 67 | comment "PC-card bridges" |
| 68 | |
| 69 | config YENTA |
| 70 | tristate "CardBus yenta-compatible bridge support" |
| 71 | depends on PCI |
| 72 | select CARDBUS if !EXPERT |
| 73 | select PCCARD_NONSTATIC if PCMCIA != n |
| 74 | ---help--- |
| 75 | This option enables support for CardBus host bridges. Virtually |
| 76 | all modern PCMCIA bridges are CardBus compatible. A "bridge" is |
| 77 | the hardware inside your computer that PCMCIA cards are plugged |
| 78 | into. |
| 79 | |
| 80 | To compile this driver as modules, choose M here: the |
| 81 | module will be called yenta_socket. |
| 82 | |
| 83 | If unsure, say Y. |
| 84 | |
| 85 | config YENTA_O2 |
| 86 | default y |
| 87 | bool "Special initialization for O2Micro bridges" if EXPERT |
| 88 | depends on YENTA |
| 89 | |
| 90 | config YENTA_RICOH |
| 91 | default y |
| 92 | bool "Special initialization for Ricoh bridges" if EXPERT |
| 93 | depends on YENTA |
| 94 | |
| 95 | config YENTA_TI |
| 96 | default y |
| 97 | bool "Special initialization for TI and EnE bridges" if EXPERT |
| 98 | depends on YENTA |
| 99 | |
| 100 | config YENTA_ENE_TUNE |
| 101 | default y |
| 102 | bool "Auto-tune EnE bridges for CB cards" if EXPERT |
| 103 | depends on YENTA_TI && CARDBUS |
| 104 | |
| 105 | config YENTA_TOSHIBA |
| 106 | default y |
| 107 | bool "Special initialization for Toshiba ToPIC bridges" if EXPERT |
| 108 | depends on YENTA |
| 109 | |
| 110 | config PD6729 |
| 111 | tristate "Cirrus PD6729 compatible bridge support" |
| 112 | depends on PCMCIA && PCI |
| 113 | select PCCARD_NONSTATIC |
| 114 | help |
| 115 | This provides support for the Cirrus PD6729 PCI-to-PCMCIA bridge |
| 116 | device, found in some older laptops and PCMCIA card readers. |
| 117 | |
| 118 | config I82092 |
| 119 | tristate "i82092 compatible bridge support" |
| 120 | depends on PCMCIA && PCI |
| 121 | select PCCARD_NONSTATIC |
| 122 | help |
| 123 | This provides support for the Intel I82092AA PCI-to-PCMCIA bridge device, |
| 124 | found in some older laptops and more commonly in evaluation boards for the |
| 125 | chip. |
| 126 | |
| 127 | config I82365 |
| 128 | tristate "i82365 compatible bridge support" |
| 129 | depends on PCMCIA && ISA |
| 130 | select PCCARD_NONSTATIC |
| 131 | help |
| 132 | Say Y here to include support for ISA-bus PCMCIA host bridges that |
| 133 | are register compatible with the Intel i82365. These are found on |
| 134 | older laptops and ISA-bus card readers for desktop systems. A |
| 135 | "bridge" is the hardware inside your computer that PCMCIA cards are |
| 136 | plugged into. If unsure, say N. |
| 137 | |
| 138 | config TCIC |
| 139 | tristate "Databook TCIC host bridge support" |
| 140 | depends on PCMCIA && ISA |
| 141 | select PCCARD_NONSTATIC |
| 142 | help |
| 143 | Say Y here to include support for the Databook TCIC family of PCMCIA |
| 144 | host bridges. These are only found on a handful of old systems. |
| 145 | "Bridge" is the name used for the hardware inside your computer that |
| 146 | PCMCIA cards are plugged into. If unsure, say N. |
| 147 | |
| 148 | config PCMCIA_M8XX |
| 149 | tristate "MPC8xx PCMCIA support" |
| 150 | depends on PCCARD && PPC && 8xx |
| 151 | select PCCARD_IODYN if PCMCIA != n |
| 152 | help |
| 153 | Say Y here to include support for PowerPC 8xx series PCMCIA |
| 154 | controller. |
| 155 | |
| 156 | This driver is also available as a module called m8xx_pcmcia. |
| 157 | |
| 158 | config PCMCIA_ALCHEMY_DEVBOARD |
| 159 | tristate "Alchemy Db/Pb1xxx PCMCIA socket services" |
| 160 | depends on MIPS_ALCHEMY && PCMCIA |
| 161 | select 64BIT_PHYS_ADDR |
| 162 | help |
| 163 | Enable this driver of you want PCMCIA support on your Alchemy |
| 164 | Db1000, Db/Pb1100, Db/Pb1500, Db/Pb1550, Db/Pb1200, DB1300 |
| 165 | board. NOT suitable for the PB1000! |
| 166 | |
| 167 | This driver is also available as a module called db1xxx_ss.ko |
| 168 | |
| 169 | config PCMCIA_XXS1500 |
| 170 | tristate "MyCable XXS1500 PCMCIA socket support" |
| 171 | depends on PCMCIA && MIPS_XXS1500 |
| 172 | select 64BIT_PHYS_ADDR |
| 173 | help |
| 174 | Support for the PCMCIA/CF socket interface on MyCable XXS1500 |
| 175 | systems. |
| 176 | |
| 177 | This driver is also available as a module called xxs1500_ss.ko |
| 178 | |
| 179 | config PCMCIA_BCM63XX |
| 180 | tristate "bcm63xx pcmcia support" |
| 181 | depends on BCM63XX && PCMCIA |
| 182 | |
| 183 | config PCMCIA_SOC_COMMON |
| 184 | tristate |
| 185 | |
| 186 | config PCMCIA_SA11XX_BASE |
| 187 | tristate |
| 188 | |
| 189 | config PCMCIA_SA1100 |
| 190 | tristate "SA1100 support" |
| 191 | depends on ARM && ARCH_SA1100 && PCMCIA |
| 192 | select PCMCIA_SOC_COMMON |
| 193 | select PCMCIA_SA11XX_BASE |
| 194 | help |
| 195 | Say Y here to include support for SA11x0-based PCMCIA or CF |
| 196 | sockets, found on HP iPAQs, Yopy, and other StrongARM(R)/ |
| 197 | Xscale(R) embedded machines. |
| 198 | |
| 199 | This driver is also available as a module called sa1100_cs. |
| 200 | |
| 201 | config PCMCIA_SA1111 |
| 202 | tristate "SA1111 support" |
| 203 | depends on ARM && SA1111 && PCMCIA |
| 204 | select PCMCIA_SOC_COMMON |
| 205 | select PCMCIA_SA11XX_BASE if ARCH_SA1100 |
| 206 | help |
| 207 | Say Y here to include support for SA1111-based PCMCIA or CF |
| 208 | sockets, found on the Jornada 720, Graphicsmaster and other |
| 209 | StrongARM(R)/Xscale(R) embedded machines. |
| 210 | |
| 211 | This driver is also available as a module called sa1111_cs. |
| 212 | |
| 213 | config PCMCIA_PXA2XX |
| 214 | tristate "PXA2xx support" |
| 215 | depends on ARM && ARCH_PXA && PCMCIA |
| 216 | depends on (ARCH_LUBBOCK || MACH_MAINSTONE || PXA_SHARPSL \ |
| 217 | || MACH_ARMCORE || ARCH_PXA_PALM || TRIZEPS_PCMCIA \ |
| 218 | || ARCOM_PCMCIA || ARCH_PXA_ESERIES || MACH_STARGATE2 \ |
| 219 | || MACH_VPAC270 || MACH_BALLOON3 || MACH_COLIBRI \ |
| 220 | || MACH_COLIBRI320 || MACH_H4700) |
| 221 | select PCMCIA_SA1111 if ARCH_LUBBOCK && SA1111 |
| 222 | select PCMCIA_SOC_COMMON |
| 223 | help |
| 224 | Say Y here to include support for the PXA2xx PCMCIA controller |
| 225 | |
| 226 | config PCMCIA_DEBUG |
| 227 | bool "Enable debugging" |
| 228 | depends on (PCMCIA_SA1111 || PCMCIA_SA1100 || PCMCIA_PXA2XX) |
| 229 | help |
| 230 | Say Y here to enable debugging for the SoC PCMCIA layer. |
| 231 | You will need to choose the debugging level either via the |
| 232 | kernel command line, or module options depending whether |
| 233 | you build the drivers as modules. |
| 234 | |
| 235 | The kernel command line options are: |
| 236 | sa11xx_core.pc_debug=N |
| 237 | pxa2xx_core.pc_debug=N |
| 238 | |
| 239 | The module option is called pc_debug=N |
| 240 | |
| 241 | In all the above examples, N is the debugging verbosity |
| 242 | level. |
| 243 | |
| 244 | config PCMCIA_PROBE |
| 245 | bool |
| 246 | default y if ISA && !ARCH_SA1100 && !ARCH_CLPS711X && !PARISC |
| 247 | |
| 248 | config M32R_PCC |
| 249 | bool "M32R PCMCIA I/F" |
| 250 | depends on M32R && CHIP_M32700 && PCMCIA |
| 251 | help |
| 252 | Say Y here to use the M32R PCMCIA controller. |
| 253 | |
| 254 | config M32R_CFC |
| 255 | bool "M32R CF I/F Controller" |
| 256 | depends on M32R && (PLAT_USRV || PLAT_M32700UT || PLAT_MAPPI2 || PLAT_MAPPI3 || PLAT_OPSPUT) |
| 257 | help |
| 258 | Say Y here to use the M32R CompactFlash controller. |
| 259 | |
| 260 | config M32R_CFC_NUM |
| 261 | int "M32R CF I/F number" |
| 262 | depends on M32R_CFC |
| 263 | default "1" if PLAT_USRV || PLAT_M32700UT || PLAT_MAPPI2 || PLAT_MAPPI3 || PLAT_OPSPUT |
| 264 | help |
| 265 | Set the number of M32R CF slots. |
| 266 | |
| 267 | config PCMCIA_VRC4171 |
| 268 | tristate "NEC VRC4171 Card Controllers support" |
| 269 | depends on CPU_VR41XX && ISA && PCMCIA |
| 270 | |
| 271 | config PCMCIA_VRC4173 |
| 272 | tristate "NEC VRC4173 CARDU support" |
| 273 | depends on CPU_VR41XX && PCI && PCMCIA |
| 274 | |
| 275 | config OMAP_CF |
| 276 | tristate "OMAP CompactFlash Controller" |
| 277 | depends on PCMCIA && ARCH_OMAP16XX |
| 278 | help |
| 279 | Say Y here to support the CompactFlash controller on OMAP. |
| 280 | Note that this doesn't support "True IDE" mode. |
| 281 | |
| 282 | config BFIN_CFPCMCIA |
| 283 | tristate "Blackfin CompactFlash PCMCIA Driver" |
| 284 | depends on PCMCIA && BLACKFIN |
| 285 | help |
| 286 | Say Y here to support the CompactFlash PCMCIA driver for Blackfin. |
| 287 | |
| 288 | |
| 289 | config AT91_CF |
| 290 | tristate "AT91 CompactFlash Controller" |
| 291 | depends on PCMCIA && ARCH_AT91RM9200 |
| 292 | help |
| 293 | Say Y here to support the CompactFlash controller on AT91 chips. |
| 294 | Or choose M to compile the driver as a module named "at91_cf". |
| 295 | |
| 296 | config ELECTRA_CF |
| 297 | tristate "Electra CompactFlash Controller" |
| 298 | depends on PCMCIA && PPC_PASEMI |
| 299 | help |
| 300 | Say Y here to support the CompactFlash controller on the |
| 301 | PA Semi Electra eval board. |
| 302 | |
| 303 | config PCCARD_NONSTATIC |
| 304 | bool |
| 305 | |
| 306 | config PCCARD_IODYN |
| 307 | bool |
| 308 | |
| 309 | endif # PCCARD |