| 1 | /* Memory-access and commands for remote NINDY process, for GDB. |
| 2 | Copyright 1990, 1991, 1992, 1993 Free Software Foundation, Inc. |
| 3 | Contributed by Intel Corporation. Modified from remote.c by Chris Benenati. |
| 4 | |
| 5 | GDB is distributed in the hope that it will be useful, but WITHOUT ANY |
| 6 | WARRANTY. No author or distributor accepts responsibility to anyone |
| 7 | for the consequences of using it or for whether it serves any |
| 8 | particular purpose or works at all, unless he says so in writing. |
| 9 | Refer to the GDB General Public License for full details. |
| 10 | |
| 11 | Everyone is granted permission to copy, modify and redistribute GDB, |
| 12 | but only under the conditions described in the GDB General Public |
| 13 | License. A copy of this license is supposed to have been given to you |
| 14 | along with GDB so you can know your rights and responsibilities. It |
| 15 | should be in a file named COPYING. Among other things, the copyright |
| 16 | notice and this notice must be preserved on all copies. |
| 17 | |
| 18 | In other words, go ahead and share GDB, but don't try to stop |
| 19 | anyone else from sharing it farther. Help stamp out software hoarding! |
| 20 | */ |
| 21 | |
| 22 | /* |
| 23 | Except for the data cache routines, this file bears little resemblence |
| 24 | to remote.c. A new (although similar) protocol has been specified, and |
| 25 | portions of the code are entirely dependent on having an i80960 with a |
| 26 | NINDY ROM monitor at the other end of the line. |
| 27 | */ |
| 28 | |
| 29 | /***************************************************************************** |
| 30 | * |
| 31 | * REMOTE COMMUNICATION PROTOCOL BETWEEN GDB960 AND THE NINDY ROM MONITOR. |
| 32 | * |
| 33 | * |
| 34 | * MODES OF OPERATION |
| 35 | * ----- -- --------- |
| 36 | * |
| 37 | * As far as NINDY is concerned, GDB is always in one of two modes: command |
| 38 | * mode or passthrough mode. |
| 39 | * |
| 40 | * In command mode (the default) pre-defined packets containing requests |
| 41 | * are sent by GDB to NINDY. NINDY never talks except in reponse to a request. |
| 42 | * |
| 43 | * Once the the user program is started, GDB enters passthrough mode, to give |
| 44 | * the user program access to the terminal. GDB remains in this mode until |
| 45 | * NINDY indicates that the program has stopped. |
| 46 | * |
| 47 | * |
| 48 | * PASSTHROUGH MODE |
| 49 | * ----------- ---- |
| 50 | * |
| 51 | * GDB writes all input received from the keyboard directly to NINDY, and writes |
| 52 | * all characters received from NINDY directly to the monitor. |
| 53 | * |
| 54 | * Keyboard input is neither buffered nor echoed to the monitor. |
| 55 | * |
| 56 | * GDB remains in passthrough mode until NINDY sends a single ^P character, |
| 57 | * to indicate that the user process has stopped. |
| 58 | * |
| 59 | * Note: |
| 60 | * GDB assumes NINDY performs a 'flushreg' when the user program stops. |
| 61 | * |
| 62 | * |
| 63 | * COMMAND MODE |
| 64 | * ------- ---- |
| 65 | * |
| 66 | * All info (except for message ack and nak) is transferred between gdb |
| 67 | * and the remote processor in messages of the following format: |
| 68 | * |
| 69 | * <info>#<checksum> |
| 70 | * |
| 71 | * where |
| 72 | * # is a literal character |
| 73 | * |
| 74 | * <info> ASCII information; all numeric information is in the |
| 75 | * form of hex digits ('0'-'9' and lowercase 'a'-'f'). |
| 76 | * |
| 77 | * <checksum> |
| 78 | * is a pair of ASCII hex digits representing an 8-bit |
| 79 | * checksum formed by adding together each of the |
| 80 | * characters in <info>. |
| 81 | * |
| 82 | * The receiver of a message always sends a single character to the sender |
| 83 | * to indicate that the checksum was good ('+') or bad ('-'); the sender |
| 84 | * re-transmits the entire message over until a '+' is received. |
| 85 | * |
| 86 | * In response to a command NINDY always sends back either data or |
| 87 | * a result code of the form "Xnn", where "nn" are hex digits and "X00" |
| 88 | * means no errors. (Exceptions: the "s" and "c" commands don't respond.) |
| 89 | * |
| 90 | * SEE THE HEADER OF THE FILE "gdb.c" IN THE NINDY MONITOR SOURCE CODE FOR A |
| 91 | * FULL DESCRIPTION OF LEGAL COMMANDS. |
| 92 | * |
| 93 | * SEE THE FILE "stop.h" IN THE NINDY MONITOR SOURCE CODE FOR A LIST |
| 94 | * OF STOP CODES. |
| 95 | * |
| 96 | ***************************************************************************/ |
| 97 | |
| 98 | #include "defs.h" |
| 99 | #include <signal.h> |
| 100 | #include <sys/types.h> |
| 101 | #include <setjmp.h> |
| 102 | |
| 103 | #include "frame.h" |
| 104 | #include "inferior.h" |
| 105 | #include "bfd.h" |
| 106 | #include "symfile.h" |
| 107 | #include "target.h" |
| 108 | #include "gdbcore.h" |
| 109 | #include "command.h" |
| 110 | #include "ieee-float.h" |
| 111 | |
| 112 | #include "wait.h" |
| 113 | #include <sys/file.h> |
| 114 | #include <ctype.h> |
| 115 | #include "serial.h" |
| 116 | #include "nindy-share/env.h" |
| 117 | #include "nindy-share/stop.h" |
| 118 | |
| 119 | #include "dcache.h" |
| 120 | #include "remote-utils.h" |
| 121 | |
| 122 | static DCACHE *nindy_dcache; |
| 123 | |
| 124 | extern int unlink(); |
| 125 | extern char *getenv(); |
| 126 | extern char *mktemp(); |
| 127 | |
| 128 | extern void generic_mourn_inferior (); |
| 129 | |
| 130 | extern struct target_ops nindy_ops; |
| 131 | extern GDB_FILE *instream; |
| 132 | extern struct ext_format ext_format_i960; /* i960-tdep.c */ |
| 133 | |
| 134 | extern char ninStopWhy (); |
| 135 | extern int ninMemGet (); |
| 136 | extern int ninMemPut (); |
| 137 | |
| 138 | int nindy_initial_brk; /* nonzero if want to send an initial BREAK to nindy */ |
| 139 | int nindy_old_protocol; /* nonzero if want to use old protocol */ |
| 140 | char *nindy_ttyname; /* name of tty to talk to nindy on, or null */ |
| 141 | |
| 142 | #define DLE '\020' /* Character NINDY sends to indicate user program has |
| 143 | * halted. */ |
| 144 | #define TRUE 1 |
| 145 | #define FALSE 0 |
| 146 | |
| 147 | /* From nindy-share/nindy.c. */ |
| 148 | extern serial_t nindy_serial; |
| 149 | |
| 150 | static int have_regs = 0; /* 1 iff regs read since i960 last halted */ |
| 151 | static int regs_changed = 0; /* 1 iff regs were modified since last read */ |
| 152 | |
| 153 | extern char *exists(); |
| 154 | |
| 155 | static void |
| 156 | nindy_fetch_registers PARAMS ((int)); |
| 157 | |
| 158 | static void |
| 159 | nindy_store_registers PARAMS ((int)); |
| 160 | \f |
| 161 | static char *savename; |
| 162 | |
| 163 | static void |
| 164 | nindy_close (quitting) |
| 165 | int quitting; |
| 166 | { |
| 167 | if (nindy_serial != NULL) |
| 168 | SERIAL_CLOSE (nindy_serial); |
| 169 | nindy_serial = NULL; |
| 170 | |
| 171 | if (savename) |
| 172 | free (savename); |
| 173 | savename = 0; |
| 174 | } |
| 175 | |
| 176 | /* Open a connection to a remote debugger. |
| 177 | FIXME, there should be "set" commands for the options that are |
| 178 | now specified with gdb command-line options (old_protocol, |
| 179 | and initial_brk). */ |
| 180 | void |
| 181 | nindy_open (name, from_tty) |
| 182 | char *name; /* "/dev/ttyXX", "ttyXX", or "XX": tty to be opened */ |
| 183 | int from_tty; |
| 184 | { |
| 185 | char baudrate[1024]; |
| 186 | |
| 187 | if (!name) |
| 188 | error_no_arg ("serial port device name"); |
| 189 | |
| 190 | target_preopen (from_tty); |
| 191 | |
| 192 | nindy_close (0); |
| 193 | |
| 194 | have_regs = regs_changed = 0; |
| 195 | nindy_dcache = dcache_init(ninMemGet, ninMemPut); |
| 196 | |
| 197 | /* Allow user to interrupt the following -- we could hang if there's |
| 198 | no NINDY at the other end of the remote tty. */ |
| 199 | immediate_quit++; |
| 200 | /* If baud_rate is -1, then ninConnect will not recognize the baud rate |
| 201 | and will deal with the situation in a (more or less) reasonable |
| 202 | fashion. */ |
| 203 | sprintf(baudrate, "%d", baud_rate); |
| 204 | ninConnect(name, baudrate, |
| 205 | nindy_initial_brk, !from_tty, nindy_old_protocol); |
| 206 | immediate_quit--; |
| 207 | |
| 208 | if (nindy_serial == NULL) |
| 209 | { |
| 210 | perror_with_name (name); |
| 211 | } |
| 212 | |
| 213 | savename = savestring (name, strlen (name)); |
| 214 | push_target (&nindy_ops); |
| 215 | target_fetch_registers(-1); |
| 216 | } |
| 217 | |
| 218 | /* User-initiated quit of nindy operations. */ |
| 219 | |
| 220 | static void |
| 221 | nindy_detach (name, from_tty) |
| 222 | char *name; |
| 223 | int from_tty; |
| 224 | { |
| 225 | if (name) |
| 226 | error ("Too many arguments"); |
| 227 | pop_target (); |
| 228 | } |
| 229 | |
| 230 | static void |
| 231 | nindy_files_info () |
| 232 | { |
| 233 | /* FIXME: this lies about the baud rate if we autobauded. */ |
| 234 | printf_unfiltered("\tAttached to %s at %d bits per second%s%s.\n", savename, |
| 235 | baud_rate, |
| 236 | nindy_old_protocol? " in old protocol": "", |
| 237 | nindy_initial_brk? " with initial break": ""); |
| 238 | } |
| 239 | \f |
| 240 | /* Return the number of characters in the buffer before |
| 241 | the first DLE character. */ |
| 242 | |
| 243 | static |
| 244 | int |
| 245 | non_dle( buf, n ) |
| 246 | char *buf; /* Character buffer; NOT '\0'-terminated */ |
| 247 | int n; /* Number of characters in buffer */ |
| 248 | { |
| 249 | int i; |
| 250 | |
| 251 | for ( i = 0; i < n; i++ ){ |
| 252 | if ( buf[i] == DLE ){ |
| 253 | break; |
| 254 | } |
| 255 | } |
| 256 | return i; |
| 257 | } |
| 258 | \f |
| 259 | /* Tell the remote machine to resume. */ |
| 260 | |
| 261 | void |
| 262 | nindy_resume (pid, step, siggnal) |
| 263 | int pid, step; |
| 264 | enum target_signal siggnal; |
| 265 | { |
| 266 | if (siggnal != TARGET_SIGNAL_0 && siggnal != stop_signal) |
| 267 | warning ("Can't send signals to remote NINDY targets."); |
| 268 | |
| 269 | dcache_flush(nindy_dcache); |
| 270 | if ( regs_changed ){ |
| 271 | nindy_store_registers (-1); |
| 272 | regs_changed = 0; |
| 273 | } |
| 274 | have_regs = 0; |
| 275 | ninGo( step ); |
| 276 | } |
| 277 | \f |
| 278 | /* FIXME, we can probably use the normal terminal_inferior stuff here. |
| 279 | We have to do terminal_inferior and then set up the passthrough |
| 280 | settings initially. Thereafter, terminal_ours and terminal_inferior |
| 281 | will automatically swap the settings around for us. */ |
| 282 | |
| 283 | struct clean_up_tty_args { |
| 284 | serial_ttystate state; |
| 285 | serial_t serial; |
| 286 | }; |
| 287 | |
| 288 | static void |
| 289 | clean_up_tty (ptrarg) |
| 290 | PTR ptrarg; |
| 291 | { |
| 292 | struct clean_up_tty_args *args = (struct clean_up_tty_args *) ptrarg; |
| 293 | SERIAL_SET_TTY_STATE (args->serial, args->state); |
| 294 | free (args->state); |
| 295 | warning ("\n\n\ |
| 296 | You may need to reset the 80960 and/or reload your program.\n"); |
| 297 | } |
| 298 | |
| 299 | /* Wait until the remote machine stops. While waiting, operate in passthrough |
| 300 | * mode; i.e., pass everything NINDY sends to gdb_stdout, and everything from |
| 301 | * stdin to NINDY. |
| 302 | * |
| 303 | * Return to caller, storing status in 'status' just as `wait' would. |
| 304 | */ |
| 305 | |
| 306 | static int |
| 307 | nindy_wait( pid, status ) |
| 308 | int pid; |
| 309 | struct target_waitstatus *status; |
| 310 | { |
| 311 | fd_set fds; |
| 312 | char buf[500]; /* FIXME, what is "500" here? */ |
| 313 | int i, n; |
| 314 | unsigned char stop_exit; |
| 315 | unsigned char stop_code; |
| 316 | struct clean_up_tty_args tty_args; |
| 317 | struct cleanup *old_cleanups; |
| 318 | long ip_value, fp_value, sp_value; /* Reg values from stop */ |
| 319 | |
| 320 | status->kind = TARGET_WAITKIND_EXITED; |
| 321 | status->value.integer = 0; |
| 322 | |
| 323 | /* OPERATE IN PASSTHROUGH MODE UNTIL NINDY SENDS A DLE CHARACTER */ |
| 324 | |
| 325 | /* Save current tty attributes, and restore them when done. */ |
| 326 | tty_args.serial = SERIAL_FDOPEN (0); |
| 327 | tty_args.state = SERIAL_GET_TTY_STATE (tty_args.serial); |
| 328 | old_cleanups = make_cleanup (clean_up_tty, &tty_args); |
| 329 | |
| 330 | /* Pass input from keyboard to NINDY as it arrives. NINDY will interpret |
| 331 | <CR> and perform echo. */ |
| 332 | /* This used to set CBREAK and clear ECHO and CRMOD. I hope this is close |
| 333 | enough. */ |
| 334 | SERIAL_RAW (tty_args.serial); |
| 335 | |
| 336 | while (1) |
| 337 | { |
| 338 | /* Wait for input on either the remote port or stdin. */ |
| 339 | FD_ZERO (&fds); |
| 340 | FD_SET (0, &fds); |
| 341 | FD_SET (nindy_serial->fd, &fds); |
| 342 | if (select (nindy_serial->fd + 1, &fds, 0, 0, 0) <= 0) |
| 343 | continue; |
| 344 | |
| 345 | /* Pass input through to correct place */ |
| 346 | if (FD_ISSET (0, &fds)) |
| 347 | { |
| 348 | /* Input on stdin */ |
| 349 | n = read (0, buf, sizeof (buf)); |
| 350 | if (n) |
| 351 | { |
| 352 | SERIAL_WRITE (nindy_serial, buf, n ); |
| 353 | } |
| 354 | } |
| 355 | |
| 356 | if (FD_ISSET (nindy_serial->fd, &fds)) |
| 357 | { |
| 358 | /* Input on remote */ |
| 359 | n = read (nindy_serial->fd, buf, sizeof (buf)); |
| 360 | if (n) |
| 361 | { |
| 362 | /* Write out any characters in buffer preceding DLE */ |
| 363 | i = non_dle( buf, n ); |
| 364 | if ( i > 0 ) |
| 365 | { |
| 366 | write (1, buf, i); |
| 367 | } |
| 368 | |
| 369 | if (i != n) |
| 370 | { |
| 371 | /* There *was* a DLE in the buffer */ |
| 372 | stop_exit = ninStopWhy(&stop_code, |
| 373 | &ip_value, &fp_value, &sp_value); |
| 374 | if (!stop_exit && (stop_code == STOP_SRQ)) |
| 375 | { |
| 376 | immediate_quit++; |
| 377 | ninSrq(); |
| 378 | immediate_quit--; |
| 379 | } |
| 380 | else |
| 381 | { |
| 382 | /* Get out of loop */ |
| 383 | supply_register (IP_REGNUM, |
| 384 | (char *)&ip_value); |
| 385 | supply_register (FP_REGNUM, |
| 386 | (char *)&fp_value); |
| 387 | supply_register (SP_REGNUM, |
| 388 | (char *)&sp_value); |
| 389 | break; |
| 390 | } |
| 391 | } |
| 392 | } |
| 393 | } |
| 394 | } |
| 395 | |
| 396 | do_cleanups (old_cleanups); |
| 397 | |
| 398 | if (stop_exit) |
| 399 | { |
| 400 | status->kind = TARGET_WAITKIND_EXITED; |
| 401 | status->value.integer = stop_code; |
| 402 | } |
| 403 | else |
| 404 | { |
| 405 | status->kind = TARGET_WAITKIND_STOPPED; |
| 406 | status->value.sig = i960_fault_to_signal (stop_code); |
| 407 | } |
| 408 | return inferior_pid; |
| 409 | } |
| 410 | |
| 411 | /* Read the remote registers into the block REGS. */ |
| 412 | |
| 413 | /* This is the block that ninRegsGet and ninRegsPut handles. */ |
| 414 | struct nindy_regs { |
| 415 | char local_regs[16 * 4]; |
| 416 | char global_regs[16 * 4]; |
| 417 | char pcw_acw[2 * 4]; |
| 418 | char ip[4]; |
| 419 | char tcw[4]; |
| 420 | char fp_as_double[4 * 8]; |
| 421 | }; |
| 422 | |
| 423 | static void |
| 424 | nindy_fetch_registers(regno) |
| 425 | int regno; |
| 426 | { |
| 427 | struct nindy_regs nindy_regs; |
| 428 | int regnum, inv; |
| 429 | double dub; |
| 430 | |
| 431 | immediate_quit++; |
| 432 | ninRegsGet( (char *) &nindy_regs ); |
| 433 | immediate_quit--; |
| 434 | |
| 435 | memcpy (®isters[REGISTER_BYTE (R0_REGNUM)], nindy_regs.local_regs, 16*4); |
| 436 | memcpy (®isters[REGISTER_BYTE (G0_REGNUM)], nindy_regs.global_regs, 16*4); |
| 437 | memcpy (®isters[REGISTER_BYTE (PCW_REGNUM)], nindy_regs.pcw_acw, 2*4); |
| 438 | memcpy (®isters[REGISTER_BYTE (IP_REGNUM)], nindy_regs.ip, 1*4); |
| 439 | memcpy (®isters[REGISTER_BYTE (TCW_REGNUM)], nindy_regs.tcw, 1*4); |
| 440 | for (regnum = FP0_REGNUM; regnum < FP0_REGNUM + 4; regnum++) { |
| 441 | dub = unpack_double (builtin_type_double, |
| 442 | &nindy_regs.fp_as_double[8 * (regnum - FP0_REGNUM)], |
| 443 | &inv); |
| 444 | /* dub now in host byte order */ |
| 445 | double_to_ieee_extended (&ext_format_i960, &dub, |
| 446 | ®isters[REGISTER_BYTE (regnum)]); |
| 447 | } |
| 448 | |
| 449 | registers_fetched (); |
| 450 | } |
| 451 | |
| 452 | static void |
| 453 | nindy_prepare_to_store() |
| 454 | { |
| 455 | /* Fetch all regs if they aren't already here. */ |
| 456 | read_register_bytes (0, NULL, REGISTER_BYTES); |
| 457 | } |
| 458 | |
| 459 | static void |
| 460 | nindy_store_registers(regno) |
| 461 | int regno; |
| 462 | { |
| 463 | struct nindy_regs nindy_regs; |
| 464 | int regnum; |
| 465 | double dub; |
| 466 | |
| 467 | memcpy (nindy_regs.local_regs, ®isters[REGISTER_BYTE (R0_REGNUM)], 16*4); |
| 468 | memcpy (nindy_regs.global_regs, ®isters[REGISTER_BYTE (G0_REGNUM)], 16*4); |
| 469 | memcpy (nindy_regs.pcw_acw, ®isters[REGISTER_BYTE (PCW_REGNUM)], 2*4); |
| 470 | memcpy (nindy_regs.ip, ®isters[REGISTER_BYTE (IP_REGNUM)], 1*4); |
| 471 | memcpy (nindy_regs.tcw, ®isters[REGISTER_BYTE (TCW_REGNUM)], 1*4); |
| 472 | for (regnum = FP0_REGNUM; regnum < FP0_REGNUM + 4; regnum++) |
| 473 | { |
| 474 | ieee_extended_to_double (&ext_format_i960, |
| 475 | ®isters[REGISTER_BYTE (regnum)], &dub); |
| 476 | store_floating (&nindy_regs.fp_as_double[8 * (regnum - FP0_REGNUM)], |
| 477 | REGISTER_VIRTUAL_SIZE (regnum), |
| 478 | dub); |
| 479 | } |
| 480 | |
| 481 | immediate_quit++; |
| 482 | ninRegsPut( (char *) &nindy_regs ); |
| 483 | immediate_quit--; |
| 484 | } |
| 485 | |
| 486 | /* Read a word from remote address ADDR and return it. |
| 487 | * This goes through the data cache. |
| 488 | */ |
| 489 | int |
| 490 | nindy_fetch_word (addr) |
| 491 | CORE_ADDR addr; |
| 492 | { |
| 493 | return dcache_fetch (nindy_dcache, addr); |
| 494 | } |
| 495 | |
| 496 | /* Write a word WORD into remote address ADDR. |
| 497 | This goes through the data cache. */ |
| 498 | |
| 499 | void |
| 500 | nindy_store_word (addr, word) |
| 501 | CORE_ADDR addr; |
| 502 | int word; |
| 503 | { |
| 504 | dcache_poke (nindy_dcache, addr, word); |
| 505 | } |
| 506 | |
| 507 | /* Copy LEN bytes to or from inferior's memory starting at MEMADDR |
| 508 | to debugger memory starting at MYADDR. Copy to inferior if |
| 509 | WRITE is nonzero. Returns the length copied. |
| 510 | |
| 511 | This is stolen almost directly from infptrace.c's child_xfer_memory, |
| 512 | which also deals with a word-oriented memory interface. Sometime, |
| 513 | FIXME, rewrite this to not use the word-oriented routines. */ |
| 514 | |
| 515 | int |
| 516 | nindy_xfer_inferior_memory(memaddr, myaddr, len, write, target) |
| 517 | CORE_ADDR memaddr; |
| 518 | char *myaddr; |
| 519 | int len; |
| 520 | int write; |
| 521 | struct target_ops *target; /* ignored */ |
| 522 | { |
| 523 | register int i; |
| 524 | /* Round starting address down to longword boundary. */ |
| 525 | register CORE_ADDR addr = memaddr & - sizeof (int); |
| 526 | /* Round ending address up; get number of longwords that makes. */ |
| 527 | register int count |
| 528 | = (((memaddr + len) - addr) + sizeof (int) - 1) / sizeof (int); |
| 529 | /* Allocate buffer of that many longwords. */ |
| 530 | register int *buffer = (int *) alloca (count * sizeof (int)); |
| 531 | |
| 532 | if (write) |
| 533 | { |
| 534 | /* Fill start and end extra bytes of buffer with existing memory data. */ |
| 535 | |
| 536 | if (addr != memaddr || len < (int)sizeof (int)) { |
| 537 | /* Need part of initial word -- fetch it. */ |
| 538 | buffer[0] = nindy_fetch_word (addr); |
| 539 | } |
| 540 | |
| 541 | if (count > 1) /* FIXME, avoid if even boundary */ |
| 542 | { |
| 543 | buffer[count - 1] |
| 544 | = nindy_fetch_word (addr + (count - 1) * sizeof (int)); |
| 545 | } |
| 546 | |
| 547 | /* Copy data to be written over corresponding part of buffer */ |
| 548 | |
| 549 | memcpy ((char *) buffer + (memaddr & (sizeof (int) - 1)), myaddr, len); |
| 550 | |
| 551 | /* Write the entire buffer. */ |
| 552 | |
| 553 | for (i = 0; i < count; i++, addr += sizeof (int)) |
| 554 | { |
| 555 | errno = 0; |
| 556 | nindy_store_word (addr, buffer[i]); |
| 557 | if (errno) |
| 558 | return 0; |
| 559 | } |
| 560 | } |
| 561 | else |
| 562 | { |
| 563 | /* Read all the longwords */ |
| 564 | for (i = 0; i < count; i++, addr += sizeof (int)) |
| 565 | { |
| 566 | errno = 0; |
| 567 | buffer[i] = nindy_fetch_word (addr); |
| 568 | if (errno) |
| 569 | return 0; |
| 570 | QUIT; |
| 571 | } |
| 572 | |
| 573 | /* Copy appropriate bytes out of the buffer. */ |
| 574 | memcpy (myaddr, (char *) buffer + (memaddr & (sizeof (int) - 1)), len); |
| 575 | } |
| 576 | return len; |
| 577 | } |
| 578 | \f |
| 579 | static void |
| 580 | nindy_create_inferior (execfile, args, env) |
| 581 | char *execfile; |
| 582 | char *args; |
| 583 | char **env; |
| 584 | { |
| 585 | int entry_pt; |
| 586 | int pid; |
| 587 | |
| 588 | if (args && *args) |
| 589 | error ("Can't pass arguments to remote NINDY process"); |
| 590 | |
| 591 | if (execfile == 0 || exec_bfd == 0) |
| 592 | error ("No exec file specified"); |
| 593 | |
| 594 | entry_pt = (int) bfd_get_start_address (exec_bfd); |
| 595 | |
| 596 | pid = 42; |
| 597 | |
| 598 | /* The "process" (board) is already stopped awaiting our commands, and |
| 599 | the program is already downloaded. We just set its PC and go. */ |
| 600 | |
| 601 | inferior_pid = pid; /* Needed for wait_for_inferior below */ |
| 602 | |
| 603 | clear_proceed_status (); |
| 604 | |
| 605 | /* Tell wait_for_inferior that we've started a new process. */ |
| 606 | init_wait_for_inferior (); |
| 607 | |
| 608 | /* Set up the "saved terminal modes" of the inferior |
| 609 | based on what modes we are starting it with. */ |
| 610 | target_terminal_init (); |
| 611 | |
| 612 | /* Install inferior's terminal modes. */ |
| 613 | target_terminal_inferior (); |
| 614 | |
| 615 | /* insert_step_breakpoint (); FIXME, do we need this? */ |
| 616 | /* Let 'er rip... */ |
| 617 | proceed ((CORE_ADDR)entry_pt, TARGET_SIGNAL_DEFAULT, 0); |
| 618 | } |
| 619 | |
| 620 | static void |
| 621 | reset_command(args, from_tty) |
| 622 | char *args; |
| 623 | int from_tty; |
| 624 | { |
| 625 | if (nindy_serial == NULL) |
| 626 | { |
| 627 | error( "No target system to reset -- use 'target nindy' command."); |
| 628 | } |
| 629 | if ( query("Really reset the target system?",0,0) ) |
| 630 | { |
| 631 | SERIAL_SEND_BREAK (nindy_serial); |
| 632 | tty_flush (nindy_serial); |
| 633 | } |
| 634 | } |
| 635 | |
| 636 | void |
| 637 | nindy_kill (args, from_tty) |
| 638 | char *args; |
| 639 | int from_tty; |
| 640 | { |
| 641 | return; /* Ignore attempts to kill target system */ |
| 642 | } |
| 643 | |
| 644 | /* Clean up when a program exits. |
| 645 | |
| 646 | The program actually lives on in the remote processor's RAM, and may be |
| 647 | run again without a download. Don't leave it full of breakpoint |
| 648 | instructions. */ |
| 649 | |
| 650 | void |
| 651 | nindy_mourn_inferior () |
| 652 | { |
| 653 | remove_breakpoints (); |
| 654 | unpush_target (&nindy_ops); |
| 655 | generic_mourn_inferior (); /* Do all the proper things now */ |
| 656 | } |
| 657 | \f |
| 658 | /* Pass the args the way catch_errors wants them. */ |
| 659 | static int |
| 660 | nindy_open_stub (arg) |
| 661 | char *arg; |
| 662 | { |
| 663 | nindy_open (arg, 1); |
| 664 | return 1; |
| 665 | } |
| 666 | |
| 667 | static int |
| 668 | load_stub (arg) |
| 669 | char *arg; |
| 670 | { |
| 671 | target_load (arg, 1); |
| 672 | return 1; |
| 673 | } |
| 674 | |
| 675 | /* This routine is run as a hook, just before the main command loop is |
| 676 | entered. If gdb is configured for the i960, but has not had its |
| 677 | nindy target specified yet, this will loop prompting the user to do so. |
| 678 | |
| 679 | Unlike the loop provided by Intel, we actually let the user get out |
| 680 | of this with a RETURN. This is useful when e.g. simply examining |
| 681 | an i960 object file on the host system. */ |
| 682 | |
| 683 | void |
| 684 | nindy_before_main_loop () |
| 685 | { |
| 686 | char ttyname[100]; |
| 687 | char *p, *p2; |
| 688 | |
| 689 | while (current_target != &nindy_ops) { /* remote tty not specified yet */ |
| 690 | if ( instream == stdin ){ |
| 691 | printf_unfiltered("\nAttach /dev/ttyNN -- specify NN, or \"quit\" to quit: "); |
| 692 | gdb_flush( gdb_stdout ); |
| 693 | } |
| 694 | fgets( ttyname, sizeof(ttyname)-1, stdin ); |
| 695 | |
| 696 | /* Strip leading and trailing whitespace */ |
| 697 | for ( p = ttyname; isspace(*p); p++ ){ |
| 698 | ; |
| 699 | } |
| 700 | if ( *p == '\0' ){ |
| 701 | return; /* User just hit spaces or return, wants out */ |
| 702 | } |
| 703 | for ( p2= p; !isspace(*p2) && (*p2 != '\0'); p2++ ){ |
| 704 | ; |
| 705 | } |
| 706 | *p2= '\0'; |
| 707 | if ( STREQ("quit",p) ){ |
| 708 | exit(1); |
| 709 | } |
| 710 | |
| 711 | if (catch_errors (nindy_open_stub, p, "", RETURN_MASK_ALL)) |
| 712 | { |
| 713 | /* Now that we have a tty open for talking to the remote machine, |
| 714 | download the executable file if one was specified. */ |
| 715 | if (exec_bfd) |
| 716 | { |
| 717 | catch_errors (load_stub, bfd_get_filename (exec_bfd), "", |
| 718 | RETURN_MASK_ALL); |
| 719 | } |
| 720 | } |
| 721 | } |
| 722 | } |
| 723 | \f |
| 724 | /* Define the target subroutine names */ |
| 725 | |
| 726 | struct target_ops nindy_ops = { |
| 727 | "nindy", "Remote serial target in i960 NINDY-specific protocol", |
| 728 | "Use a remote i960 system running NINDY connected by a serial line.\n\ |
| 729 | Specify the name of the device the serial line is connected to.\n\ |
| 730 | The speed (baud rate), whether to use the old NINDY protocol,\n\ |
| 731 | and whether to send a break on startup, are controlled by options\n\ |
| 732 | specified when you started GDB.", |
| 733 | nindy_open, nindy_close, |
| 734 | 0, |
| 735 | nindy_detach, |
| 736 | nindy_resume, |
| 737 | nindy_wait, |
| 738 | nindy_fetch_registers, nindy_store_registers, |
| 739 | nindy_prepare_to_store, |
| 740 | nindy_xfer_inferior_memory, nindy_files_info, |
| 741 | 0, 0, /* insert_breakpoint, remove_breakpoint, */ |
| 742 | 0, 0, 0, 0, 0, /* Terminal crud */ |
| 743 | nindy_kill, |
| 744 | generic_load, |
| 745 | 0, /* lookup_symbol */ |
| 746 | nindy_create_inferior, |
| 747 | nindy_mourn_inferior, |
| 748 | 0, /* can_run */ |
| 749 | 0, /* notice_signals */ |
| 750 | process_stratum, 0, /* next */ |
| 751 | 1, 1, 1, 1, 1, /* all mem, mem, stack, regs, exec */ |
| 752 | 0, 0, /* Section pointers */ |
| 753 | OPS_MAGIC, /* Always the last thing */ |
| 754 | }; |
| 755 | |
| 756 | void |
| 757 | _initialize_nindy () |
| 758 | { |
| 759 | add_target (&nindy_ops); |
| 760 | add_com ("reset", class_obscure, reset_command, |
| 761 | "Send a 'break' to the remote target system.\n\ |
| 762 | Only useful if the target has been equipped with a circuit\n\ |
| 763 | to perform a hard reset when a break is detected."); |
| 764 | } |