Documentation/devicetree/bindings/mfd/da9062.txt

   1 * Dialog DA9062 Power Management Integrated Circuit (PMIC)
   2
   3 DA9062 consists of a large and varied group of sub-devices:
   4
   5 Device                   Supply Names    Description
   6 ------                   ------------    -----------
   7 da9062-regulator        :               : LDOs & BUCKs
   8 da9062-rtc              :               : Real-Time Clock
   9 da9062-watchdog         :               : Watchdog Timer
  10
  11 ======
  12
  13 Required properties:
  14
  15 - compatible : Should be "dlg,da9062".
  16 - reg : Specifies the I2C slave address (this defaults to 0x58 but it can be
  17   modified to match the chip's OTP settings).
  18 - interrupt-parent : Specifies the reference to the interrupt controller for
  19   the DA9062.
  20 - interrupts : IRQ line information.
  21 - interrupt-controller
  22
  23 See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt for
  24 further information on IRQ bindings.
  25
  26 Sub-nodes:
  27
  28 - regulators : This node defines the settings for the LDOs and BUCKs. The
  29   DA9062 regulators are bound using their names listed below:
  30
  31     buck1    : BUCK_1
  32     buck2    : BUCK_2
  33     buck3    : BUCK_3
  34     buck4    : BUCK_4
  35     ldo1     : LDO_1
  36     ldo2     : LDO_2
  37     ldo3     : LDO_3
  38     ldo4     : LDO_4
  39
  40   The component follows the standard regulator framework and the bindings
  41   details of individual regulator device can be found in:
  42   Documentation/devicetree/bindings/regulator/regulator.txt
  43
  44
  45 - rtc : This node defines settings required for the Real-Time Clock associated
  46   with the DA9062. There are currently no entries in this binding, however
  47   compatible = "dlg,da9062-rtc" should be added if a node is created.
  48
  49 - watchdog: This node defines the settings for the watchdog driver associated
  50   with the DA9062 PMIC. The compatible = "dlg,da9062-watchdog" should be added
  51   if a node is created.
  52
  53
  54 Example:
  55
  56         pmic0: da9062@58 {
  57                 compatible = "dlg,da9062";
  58                 reg = <0x58>;
  59                 interrupt-parent = <&gpio6>;
  60                 interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
  61                 interrupt-controller;
  62
  63                 rtc {
  64                         compatible = "dlg,da9062-rtc";
  65                 };
  66
  67                 watchdog {
  68                         compatible = "dlg,da9062-watchdog";
  69                 };
  70
  71                 regulators {
  72                         DA9062_BUCK1: buck1 {
  73                                 regulator-name = "BUCK1";
  74                                 regulator-min-microvolt = <300000>;
  75                                 regulator-max-microvolt = <1570000>;
  76                                 regulator-min-microamp = <500000>;
  77                                 regulator-max-microamp = <2000000>;
  78                                 regulator-boot-on;
  79                         };
  80                         DA9062_LDO1: ldo1 {
  81                                 regulator-name = "LDO_1";
  82                                 regulator-min-microvolt = <900000>;
  83                                 regulator-max-microvolt = <3600000>;
  84                                 regulator-boot-on;
  85                         };
  86                 };
  87         };
  88