x86: Move call to print_modules() out of show_regs()
[deliverable/linux.git] / Documentation / devicetree / bindings / mfd / mc13xxx.txt
1 * Freescale MC13783/MC13892 Power Management Integrated Circuit (PMIC)
2
3 Required properties:
4 - compatible : Should be "fsl,mc13783" or "fsl,mc13892"
5
6 Optional properties:
7 - fsl,mc13xxx-uses-adc : Indicate the ADC is being used
8 - fsl,mc13xxx-uses-codec : Indicate the Audio Codec is being used
9 - fsl,mc13xxx-uses-rtc : Indicate the RTC is being used
10 - fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used
11
12 Sub-nodes:
13 - regulators : Contain the regulator nodes. The MC13892 regulators are
14 bound using their names as listed below with their registers and bits
15 for enabling.
16
17 vcoincell : regulator VCOINCELL (register 13, bit 23)
18 sw1 : regulator SW1 (register 24, bit 0)
19 sw2 : regulator SW2 (register 25, bit 0)
20 sw3 : regulator SW3 (register 26, bit 0)
21 sw4 : regulator SW4 (register 27, bit 0)
22 swbst : regulator SWBST (register 29, bit 20)
23 vgen1 : regulator VGEN1 (register 32, bit 0)
24 viohi : regulator VIOHI (register 32, bit 3)
25 vdig : regulator VDIG (register 32, bit 9)
26 vgen2 : regulator VGEN2 (register 32, bit 12)
27 vpll : regulator VPLL (register 32, bit 15)
28 vusb2 : regulator VUSB2 (register 32, bit 18)
29 vgen3 : regulator VGEN3 (register 33, bit 0)
30 vcam : regulator VCAM (register 33, bit 6)
31 vvideo : regulator VVIDEO (register 33, bit 12)
32 vaudio : regulator VAUDIO (register 33, bit 15)
33 vsd : regulator VSD (register 33, bit 18)
34 gpo1 : regulator GPO1 (register 34, bit 6)
35 gpo2 : regulator GPO2 (register 34, bit 8)
36 gpo3 : regulator GPO3 (register 34, bit 10)
37 gpo4 : regulator GPO4 (register 34, bit 12)
38 pwgt1spi : regulator PWGT1SPI (register 34, bit 15)
39 pwgt2spi : regulator PWGT2SPI (register 34, bit 16)
40 vusb : regulator VUSB (register 50, bit 3)
41
42 The bindings details of individual regulator device can be found in:
43 Documentation/devicetree/bindings/regulator/regulator.txt
44
45 Examples:
46
47 ecspi@70010000 { /* ECSPI1 */
48 fsl,spi-num-chipselects = <2>;
49 cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */
50 <&gpio3 25 0>; /* GPIO4_25 */
51 status = "okay";
52
53 pmic: mc13892@0 {
54 #address-cells = <1>;
55 #size-cells = <0>;
56 compatible = "fsl,mc13892";
57 spi-max-frequency = <6000000>;
58 reg = <0>;
59 interrupt-parent = <&gpio0>;
60 interrupts = <8>;
61
62 regulators {
63 sw1_reg: mc13892__sw1 {
64 regulator-min-microvolt = <600000>;
65 regulator-max-microvolt = <1375000>;
66 regulator-boot-on;
67 regulator-always-on;
68 };
69
70 sw2_reg: mc13892__sw2 {
71 regulator-min-microvolt = <900000>;
72 regulator-max-microvolt = <1850000>;
73 regulator-boot-on;
74 regulator-always-on;
75 };
76 };
77 };
78 };
This page took 0.050975 seconds and 5 git commands to generate.