Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt

   1 * Mediatek MT65XX Pin Controller
   2
   3 The Mediatek's Pin controller is used to control SoC pins.
   4
   5 Required properties:
   6 - compatible: value should be one of the following.
   7         "mediatek,mt2701-pinctrl", compatible with mt2701 pinctrl.
   8         "mediatek,mt6397-pinctrl", compatible with mt6397 pinctrl.
   9         "mediatek,mt7623-pinctrl", compatible with mt7623 pinctrl.
  10         "mediatek,mt8127-pinctrl", compatible with mt8127 pinctrl.
  11         "mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl.
  12         "mediatek,mt8173-pinctrl", compatible with mt8173 pinctrl.
  13 - pins-are-numbered: Specify the subnodes are using numbered pinmux to
  14   specify pins.
  15 - gpio-controller : Marks the device node as a gpio controller.
  16 - #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
  17   binding is used, the amount of cells must be specified as 2. See the below
  18   mentioned gpio binding representation for description of particular cells.
  19
  20         Eg: <&pio 6 0>
  21         <[phandle of the gpio controller node]
  22         [line number within the gpio controller]
  23         [flags]>
  24
  25         Values for gpio specifier:
  26         - Line number: is a value between 0 to 202.
  27         - Flags:  bit field of flags, as defined in <dt-bindings/gpio/gpio.h>.
  28             Only the following flags are supported:
  29             0 - GPIO_ACTIVE_HIGH
  30             1 - GPIO_ACTIVE_LOW
  31
  32 Optional properties:
  33 - mediatek,pctl-regmap: Should be a phandle of the syscfg node.
  34 - reg: physicall address base for EINT registers
  35 - interrupt-controller: Marks the device node as an interrupt controller
  36 - #interrupt-cells: Should be two.
  37 - interrupts : The interrupt outputs from the controller.
  38
  39 Please refer to pinctrl-bindings.txt in this directory for details of the
  40 common pinctrl bindings used by client devices.
  41
  42 Subnode format
  43 A pinctrl node should contain at least one subnodes representing the
  44 pinctrl groups available on the machine. Each subnode will list the
  45 pins it needs, and how they should be configured, with regard to muxer
  46 configuration, pullups, drive strength, input enable/disable and input schmitt.
  47
  48     node {
  49         pinmux = <PIN_NUMBER_PINMUX>;
  50         GENERIC_PINCONFIG;
  51     };
  52
  53 Required properties:
  54 - pinmux: integer array, represents gpio pin number and mux setting.
  55     Supported pin number and mux varies for different SoCs, and are defined
  56     as macros in boot/dts/<soc>-pinfunc.h directly.
  57
  58 Optional properties:
  59 - GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable,
  60     bias-pull-down, bias-pull-up, input-enable, input-disable, output-low, output-high,
  61     input-schmitt-enable, input-schmitt-disable and drive-strength are valid.
  62
  63     Some special pins have extra pull up strength, there are R0 and R1 pull-up
  64     resistors available, but for user, it's only need to set R1R0 as 00, 01, 10 or 11.
  65     So when config bias-pull-up, it support arguments for those special pins.
  66     Some macros have been defined for this usage, such as MTK_PUPD_SET_R1R0_00.
  67     See dt-bindings/pinctrl/mt65xx.h.
  68
  69     When config drive-strength, it can support some arguments, such as
  70     MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See dt-bindings/pinctrl/mt65xx.h.
  71
  72 Examples:
  73
  74 #include "mt8135-pinfunc.h"
  75
  76 ...
  77 {
  78         syscfg_pctl_a: syscfg_pctl_a@10005000 {
  79                 compatible = "mediatek,mt8135-pctl-a-syscfg", "syscon";
  80                 reg = <0 0x10005000 0 0x1000>;
  81         };
  82
  83         syscfg_pctl_b: syscfg_pctl_b@1020C020 {
  84                 compatible = "mediatek,mt8135-pctl-b-syscfg", "syscon";
  85                 reg = <0 0x1020C020 0 0x1000>;
  86         };
  87
  88         pinctrl@01c20800 {
  89                 compatible = "mediatek,mt8135-pinctrl";
  90                 reg = <0 0x1000B000 0 0x1000>;
  91                 mediatek,pctl-regmap = <&syscfg_pctl_a &syscfg_pctl_b>;
  92                 pins-are-numbered;
  93                 gpio-controller;
  94                 #gpio-cells = <2>;
  95                 interrupt-controller;
  96                 #interrupt-cells = <2>;
  97                 interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
  98                                 <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
  99                                 <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
 100
 101                 i2c0_pins_a: i2c0@0 {
 102                         pins1 {
 103                                 pinmux = <MT8135_PIN_100_SDA0__FUNC_SDA0>,
 104                                          <MT8135_PIN_101_SCL0__FUNC_SCL0>;
 105                                 bias-disable;
 106                         };
 107                 };
 108
 109                 i2c1_pins_a: i2c1@0 {
 110                         pins {
 111                                 pinmux = <MT8135_PIN_195_SDA1__FUNC_SDA1>,
 112                                          <MT8135_PIN_196_SCL1__FUNC_SCL1>;
 113                                 bias-pull-up = <55>;
 114                         };
 115                 };
 116
 117                 i2c2_pins_a: i2c2@0 {
 118                         pins1 {
 119                                 pinmux = <MT8135_PIN_193_SDA2__FUNC_SDA2>;
 120                                 bias-pull-down;
 121                         };
 122
 123                         pins2 {
 124                                 pinmux = <MT8135_PIN_49_WATCHDOG__FUNC_GPIO49>;
 125                                 bias-pull-up;
 126                         };
 127                 };
 128
 129                 i2c3_pins_a: i2c3@0 {
 130                         pins1 {
 131                                 pinmux = <MT8135_PIN_40_DAC_CLK__FUNC_GPIO40>,
 132                                          <MT8135_PIN_41_DAC_WS__FUNC_GPIO41>;
 133                                 bias-pull-up = <55>;
 134                         };
 135
 136                         pins2 {
 137                                 pinmux = <MT8135_PIN_35_SCL3__FUNC_SCL3>,
 138                                          <MT8135_PIN_36_SDA3__FUNC_SDA3>;
 139                                 output-low;
 140                                 bias-pull-up = <55>;
 141                         };
 142
 143                         pins3 {
 144                                 pinmux = <MT8135_PIN_57_JTCK__FUNC_GPIO57>,
 145                                          <MT8135_PIN_60_JTDI__FUNC_JTDI>;
 146                                 drive-strength = <32>;
 147                         };
 148                 };
 149
 150                 ...
 151         }
 152 };