Documentation/devicetree/bindings/remoteproc/qcom,q6v5.txt

   1 Qualcomm Hexagon Peripheral Image Loader
   2
   3 This document defines the binding for a component that loads and boots firmware
   4 on the Qualcomm Hexagon core.
   5
   6 - compatible:
   7         Usage: required
   8         Value type: <string>
   9         Definition: must be one of:
  10                     "qcom,q6v5-pil"
  11
  12 - reg:
  13         Usage: required
  14         Value type: <prop-encoded-array>
  15         Definition: must specify the base address and size of the qdsp6 and
  16                     rmb register blocks
  17
  18 - reg-names:
  19         Usage: required
  20         Value type: <stringlist>
  21         Definition: must be "q6dsp" and "rmb"
  22
  23 - interrupts-extended:
  24         Usage: required
  25         Value type: <prop-encoded-array>
  26         Definition: must list the watchdog, fatal IRQs ready, handover and
  27                     stop-ack IRQs
  28
  29 - interrupt-names:
  30         Usage: required
  31         Value type: <stringlist>
  32         Definition: must be "wdog", "fatal", "ready", "handover", "stop-ack"
  33
  34 - clocks:
  35         Usage: required
  36         Value type: <phandle>
  37         Definition: reference to the iface, bus and mem clocks to be held on
  38                     behalf of the booting of the Hexagon core
  39
  40 - clock-names:
  41         Usage: required
  42         Value type: <stringlist>
  43         Definition: must be "iface", "bus", "mem"
  44
  45 - resets:
  46         Usage: required
  47         Value type: <phandle>
  48         Definition: reference to the reset-controller for the modem sub-system
  49
  50 - reset-names:
  51         Usage: required
  52         Value type: <stringlist>
  53         Definition: must be "mss_restart"
  54
  55 - cx-supply:
  56 - mss-supply:
  57 - mx-supply:
  58 - pll-supply:
  59         Usage: required
  60         Value type: <phandle>
  61         Definition: reference to the regulators to be held on behalf of the
  62                     booting of the Hexagon core
  63
  64 - qcom,smem-states:
  65         Usage: required
  66         Value type: <phandle>
  67         Definition: reference to the smem state for requesting the Hexagon to
  68                     shut down
  69
  70 - qcom,smem-state-names:
  71         Usage: required
  72         Value type: <stringlist>
  73         Definition: must be "stop"
  74
  75 - qcom,halt-regs:
  76         Usage: required
  77         Value type: <prop-encoded-array>
  78         Definition: a phandle reference to a syscon representing TCSR followed
  79                     by the three offsets within syscon for q6, modem and nc
  80                     halt registers.
  81
  82 = SUBNODES:
  83 The Hexagon node must contain two subnodes, named "mba" and "mpss" representing
  84 the memory regions used by the Hexagon firmware. Each sub-node must contain:
  85
  86 - memory-region:
  87         Usage: required
  88         Value type: <phandle>
  89         Definition: reference to the reserved-memory for the region
  90
  91 = EXAMPLE
  92 The following example describes the resources needed to boot control the
  93 Hexagon, as it is found on MSM8974 boards.
  94
  95         modem-rproc@fc880000 {
  96                 compatible = "qcom,q6v5-pil";
  97                 reg = <0xfc880000 0x100>,
  98                       <0xfc820000 0x020>;
  99                 reg-names = "qdsp6", "rmb";
 100
 101                 interrupts-extended = <&intc 0 24 1>,
 102                                       <&modem_smp2p_in 0 0>,
 103                                       <&modem_smp2p_in 1 0>,
 104                                       <&modem_smp2p_in 2 0>,
 105                                       <&modem_smp2p_in 3 0>;
 106                 interrupt-names = "wdog",
 107                                   "fatal",
 108                                   "ready",
 109                                   "handover",
 110                                   "stop-ack";
 111
 112                 clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
 113                          <&gcc GCC_MSS_CFG_AHB_CLK>,
 114                          <&gcc GCC_BOOT_ROM_AHB_CLK>;
 115                 clock-names = "iface", "bus", "mem";
 116
 117                 qcom,halt-regs = <&tcsr_mutex_block 0x1180 0x1200 0x1280>;
 118
 119                 resets = <&gcc GCC_MSS_RESTART>;
 120                 reset-names = "mss_restart";
 121
 122                 cx-supply = <&pm8841_s2>;
 123                 mss-supply = <&pm8841_s3>;
 124                 mx-supply = <&pm8841_s1>;
 125                 pll-supply = <&pm8941_l12>;
 126
 127                 qcom,smem-states = <&modem_smp2p_out 0>;
 128                 qcom,smem-state-names = "stop";
 129
 130                 mba {
 131                         memory-region = <&mba_region>;
 132                 };
 133
 134                 mpss {
 135                         memory-region = <&mpss_region>;
 136                 };
 137         };