4 The following is a consolidated list of the kernel parameters as implemented
5 (mostly) by the __setup() macro and sorted into English Dictionary order
6 (defined as ignoring all punctuation and sorting digits before letters in a
7 case insensitive manner), and with descriptions where known.
9 Module parameters for loadable modules are specified only as the
10 parameter name with optional '=' and value as appropriate, such as:
12 modprobe usbcore blinkenlights=1
14 Module parameters for modules that are built into the kernel image
15 are specified on the kernel command line with the module name plus
16 '.' plus parameter name, with '=' and value if appropriate, such as:
18 usbcore.blinkenlights=1
20 Hyphens (dashes) and underscores are equivalent in parameter names, so
21 log_buf_len=1M print-fatal-signals=1
22 can also be entered as
23 log-buf-len=1M print_fatal_signals=1
26 This document may not be entirely up to date and comprehensive. The command
27 "modinfo -p ${modulename}" shows a current list of all parameters of a loadable
28 module. Loadable modules, after being loaded into the running kernel, also
29 reveal their parameters in /sys/module/${modulename}/parameters/. Some of these
30 parameters may be changed at runtime by the command
31 "echo -n ${value} > /sys/module/${modulename}/parameters/${parm}".
33 The parameters listed below are only valid if certain kernel build options were
34 enabled and if respective hardware is present. The text in square brackets at
35 the beginning of each description states the restrictions within which a
36 parameter is applicable:
38 ACPI ACPI support is enabled.
39 AGP AGP (Accelerated Graphics Port) is enabled.
40 ALSA ALSA sound support is enabled.
41 APIC APIC support is enabled.
42 APM Advanced Power Management support is enabled.
43 ARM ARM architecture is enabled.
44 AVR32 AVR32 architecture is enabled.
45 AX25 Appropriate AX.25 support is enabled.
46 BLACKFIN Blackfin architecture is enabled.
47 DRM Direct Rendering Management support is enabled.
48 DYNAMIC_DEBUG Build in debug messages and enable them at runtime
49 EDD BIOS Enhanced Disk Drive Services (EDD) is enabled
50 EFI EFI Partitioning (GPT) is enabled
51 EIDE EIDE/ATAPI support is enabled.
52 EVM Extended Verification Module
53 FB The frame buffer device is enabled.
54 FTRACE Function tracing enabled.
55 GCOV GCOV profiling is enabled.
56 HW Appropriate hardware is enabled.
57 IA-64 IA-64 architecture is enabled.
58 IMA Integrity measurement architecture is enabled.
59 IOSCHED More than one I/O scheduler is enabled.
60 IP_PNP IP DHCP, BOOTP, or RARP is enabled.
61 IPV6 IPv6 support is enabled.
62 ISAPNP ISA PnP code is enabled.
63 ISDN Appropriate ISDN support is enabled.
64 JOY Appropriate joystick support is enabled.
65 KGDB Kernel debugger support is enabled.
66 KVM Kernel Virtual Machine support is enabled.
67 LIBATA Libata driver is enabled
68 LP Printer support is enabled.
69 LOOP Loopback device support is enabled.
70 M68k M68k architecture is enabled.
71 These options have more detailed description inside of
72 Documentation/m68k/kernel-options.txt.
73 MDA MDA console support is enabled.
74 MIPS MIPS architecture is enabled.
75 MOUSE Appropriate mouse support is enabled.
76 MSI Message Signaled Interrupts (PCI).
77 MTD MTD (Memory Technology Device) support is enabled.
78 NET Appropriate network support is enabled.
79 NUMA NUMA support is enabled.
80 NFS Appropriate NFS support is enabled.
81 OSS OSS sound support is enabled.
82 PV_OPS A paravirtualized kernel is enabled.
83 PARIDE The ParIDE (parallel port IDE) subsystem is enabled.
84 PARISC The PA-RISC architecture is enabled.
85 PCI PCI bus support is enabled.
86 PCIE PCI Express support is enabled.
87 PCMCIA The PCMCIA subsystem is enabled.
88 PNP Plug & Play support is enabled.
89 PPC PowerPC architecture is enabled.
90 PPT Parallel port support is enabled.
91 PS2 Appropriate PS/2 support is enabled.
92 RAM RAM disk support is enabled.
93 S390 S390 architecture is enabled.
94 SCSI Appropriate SCSI support is enabled.
95 A lot of drivers have their options described inside
96 the Documentation/scsi/ sub-directory.
97 SECURITY Different security models are enabled.
98 SELINUX SELinux support is enabled.
99 APPARMOR AppArmor support is enabled.
100 SERIAL Serial support is enabled.
101 SH SuperH architecture is enabled.
102 SMP The kernel is an SMP kernel.
103 SPARC Sparc architecture is enabled.
104 SWSUSP Software suspend (hibernation) is enabled.
105 SUSPEND System suspend states are enabled.
106 TPM TPM drivers are enabled.
107 TS Appropriate touchscreen support is enabled.
108 UMS USB Mass Storage support is enabled.
109 USB USB support is enabled.
110 USBHID USB Human Interface Device support is enabled.
111 V4L Video For Linux support is enabled.
112 VMMIO Driver for memory mapped virtio devices is enabled.
113 VGA The VGA console has been enabled.
114 VT Virtual terminal support is enabled.
115 WDT Watchdog support is enabled.
116 XT IBM PC/XT MFM hard disk support is enabled.
117 X86-32 X86-32, aka i386 architecture is enabled.
118 X86-64 X86-64 architecture is enabled.
119 More X86-64 boot options can be found in
120 Documentation/x86/x86_64/boot-options.txt .
121 X86 Either 32-bit or 64-bit x86 (same as X86-32+X86-64)
122 XEN Xen support is enabled
124 In addition, the following text indicates that the option:
126 BUGS= Relates to possible processor bugs on the said processor.
127 KNL Is a kernel start-up parameter.
128 BOOT Is a boot loader parameter.
130 Parameters denoted with BOOT are actually interpreted by the boot
131 loader, and have no meaning to the kernel directly.
132 Do not modify the syntax of boot loader parameters without extreme
133 need or coordination with <Documentation/x86/boot.txt>.
135 There are also arch-specific kernel-parameters not documented here.
136 See for example <Documentation/x86/x86_64/boot-options.txt>.
138 Note that ALL kernel parameters listed below are CASE SENSITIVE, and that
139 a trailing = on the name of any parameter states that that parameter will
140 be entered as an environment variable, whereas its absence indicates that
141 it will appear as a kernel argument readable via /proc/cmdline by programs
142 running once the system is up.
144 The number of kernel parameters is not limited, but the length of the
145 complete command line (parameters including spaces etc.) is limited to
146 a fixed number of characters. This limit depends on the architecture
147 and is between 256 and 4096 characters. It is defined in the file
148 ./include/asm/setup.h as COMMAND_LINE_SIZE.
150 Finally, the [KMG] suffix is commonly described after a number of kernel
151 parameter values. These 'K', 'M', and 'G' letters represent the _binary_
152 multipliers 'Kilo', 'Mega', and 'Giga', equalling 2^10, 2^20, and 2^30
153 bytes respectively. Such letter suffixes can also be entirely omitted.
157 Advanced Configuration and Power Interface
158 Format: { force | off | strict | noirq | rsdt }
159 force -- enable ACPI if default was off
160 off -- disable ACPI if default was on
161 noirq -- do not use ACPI for IRQ routing
162 strict -- Be less tolerant of platforms that are not
163 strictly ACPI specification compliant.
164 rsdt -- prefer RSDT over (default) XSDT
165 copy_dsdt -- copy DSDT to memory
167 See also Documentation/power/runtime_pm.txt, pci=noacpi
169 acpi_rsdp= [ACPI,EFI,KEXEC]
170 Pass the RSDP address to the kernel, mostly used
171 on machines running EFI runtime service to boot the
172 second kernel for kdump.
174 acpi_apic_instance= [ACPI, IOAPIC]
176 2: use 2nd APIC table, if available
177 1,0: use 1st APIC table
180 acpi_backlight= [HW,ACPI]
181 acpi_backlight=vendor
183 If set to vendor, prefer vendor specific driver
184 (e.g. thinkpad_acpi, sony_acpi, etc.) instead
185 of the ACPI video.ko driver.
187 acpi.debug_layer= [HW,ACPI,ACPI_DEBUG]
188 acpi.debug_level= [HW,ACPI,ACPI_DEBUG]
190 CONFIG_ACPI_DEBUG must be enabled to produce any ACPI
191 debug output. Bits in debug_layer correspond to a
192 _COMPONENT in an ACPI source file, e.g.,
193 #define _COMPONENT ACPI_PCI_COMPONENT
194 Bits in debug_level correspond to a level in
195 ACPI_DEBUG_PRINT statements, e.g.,
196 ACPI_DEBUG_PRINT((ACPI_DB_INFO, ...
197 The debug_level mask defaults to "info". See
198 Documentation/acpi/debug.txt for more information about
199 debug layers and levels.
201 Enable processor driver info messages:
202 acpi.debug_layer=0x20000000
203 Enable PCI/PCI interrupt routing info messages:
204 acpi.debug_layer=0x400000
205 Enable AML "Debug" output, i.e., stores to the Debug
206 object while interpreting AML:
207 acpi.debug_layer=0xffffffff acpi.debug_level=0x2
208 Enable all messages related to ACPI hardware:
209 acpi.debug_layer=0x2 acpi.debug_level=0xffffffff
211 Some values produce so much output that the system is
212 unusable. The "log_buf_len" parameter may be useful
213 if you need to capture more output.
215 acpi_irq_balance [HW,ACPI]
216 ACPI will balance active IRQs
219 acpi_irq_nobalance [HW,ACPI]
220 ACPI will not move active IRQs (default)
223 acpi_irq_isa= [HW,ACPI] If irq_balance, mark listed IRQs used by ISA
224 Format: <irq>,<irq>...
226 acpi_irq_pci= [HW,ACPI] If irq_balance, clear listed IRQs for
228 Format: <irq>,<irq>...
230 acpi_no_auto_ssdt [HW,ACPI] Disable automatic loading of SSDT
232 acpi_os_name= [HW,ACPI] Tell ACPI BIOS the name of the OS
233 Format: To spoof as Windows 98: ="Microsoft Windows"
235 acpi_osi= [HW,ACPI] Modify list of supported OS interface strings
236 acpi_osi="string1" # add string1 -- only one string
237 acpi_osi="!string2" # remove built-in string2
238 acpi_osi= # disable all strings
241 Override the pmtimer bug detection: force the kernel
242 to assume that this machine's pmtimer latches its value
243 and always returns good values.
245 acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode
246 Format: { level | edge | high | low }
248 acpi_serialize [HW,ACPI] force serialization of AML methods
250 acpi_skip_timer_override [HW,ACPI]
251 Recognize and ignore IRQ0/pin2 Interrupt Override.
252 For broken nForce2 BIOS resulting in XT-PIC timer.
254 acpi_sleep= [HW,ACPI] Sleep options
255 Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
256 old_ordering, nonvs, sci_force_enable }
257 See Documentation/power/video.txt for information on
259 s3_beep is for debugging; it makes the PC's speaker beep
260 as soon as the kernel's real-mode entry point is called.
261 s4_nohwsig prevents ACPI hardware signature from being
262 used during resume from hibernation.
263 old_ordering causes the ACPI 1.0 ordering of the _PTS
264 control method, with respect to putting devices into
265 low power states, to be enforced (the ACPI 2.0 ordering
266 of _PTS is used by default).
267 nonvs prevents the kernel from saving/restoring the
268 ACPI NVS memory during suspend/hibernation and resume.
269 sci_force_enable causes the kernel to set SCI_EN directly
270 on resume from S1/S3 (which is against the ACPI spec,
271 but some broken systems don't work without it).
273 acpi_use_timer_override [HW,ACPI]
274 Use timer override. For some broken Nvidia NF5 boards
275 that require a timer override, but don't have HPET
277 acpi_enforce_resources= [ACPI]
278 { strict | lax | no }
279 Check for resource conflicts between native drivers
280 and ACPI OperationRegions (SystemIO and SystemMemory
281 only). IO ports and memory declared in ACPI might be
282 used by the ACPI subsystem in arbitrary AML code and
283 can interfere with legacy drivers.
284 strict (default): access to resources claimed by ACPI
285 is denied; legacy drivers trying to access reserved
286 resources will fail to bind to device using them.
287 lax: access to resources claimed by ACPI is allowed;
288 legacy drivers trying to access reserved resources
289 will bind successfully but a warning message is logged.
290 no: ACPI OperationRegions are not marked as reserved,
291 no further checks are performed.
293 add_efi_memmap [EFI; X86] Include EFI memory map in
294 kernel's map of available physical RAM.
297 { off | try_unsupported }
298 off: disable AGP support
299 try_unsupported: try to drive unsupported chipsets
300 (may crash computer or cause data corruption)
303 See Documentation/sound/alsa/alsa-parameters.txt
306 Allow the default userspace alignment fault handler
307 behaviour to be specified. Bit 0 enables warnings,
308 bit 1 enables fixups, and bit 2 sends a segfault.
310 align_va_addr= [X86-64]
311 Align virtual addresses by clearing slice [14:12] when
312 allocating a VMA at process creation time. This option
313 gives you up to 3% performance improvement on AMD F15h
314 machines (where it is enabled by default) for a
315 CPU-intensive style benchmark, and it can vary highly in
316 a microbenchmark depending on workload and compiler.
318 32: only for 32-bit processes
319 64: only for 64-bit processes
320 on: enable for both 32- and 64-bit processes
321 off: disable for both 32- and 64-bit processes
323 amd_iommu= [HW,X86-64]
324 Pass parameters to the AMD IOMMU driver in the system.
326 fullflush - enable flushing of IO/TLB entries when
327 they are unmapped. Otherwise they are
328 flushed before they will be reused, which
330 off - do not initialize any AMD IOMMU found in
332 force_isolation - Force device isolation for all
333 devices. The IOMMU driver is not
334 allowed anymore to lift isolation
335 requirements as needed. This option
336 does not override iommu=pt
338 amd_iommu_dump= [HW,X86-64]
339 Enable AMD IOMMU driver option to dump the ACPI table
340 for AMD IOMMU. With this option enabled, AMD IOMMU
341 driver will print ACPI tables for AMD IOMMU during
342 IOMMU initialization.
344 amijoy.map= [HW,JOY] Amiga joystick support
345 Map of devices attached to JOY0DAT and JOY1DAT
347 See also Documentation/input/joystick.txt
349 analog.map= [HW,JOY] Analog joystick and gamepad support
350 Specifies type or capabilities of an analog joystick
351 connected to one of 16 gameports
352 Format: <type1>,<type2>,..<type16>
355 Power management functions (SPARCstation-4/5 + deriv.)
357 Disable APC CPU standby support. SPARCstation-Fox does
358 not play well with APC CPU idle - disable it if you have
359 APC and your system crashes randomly.
361 apic= [APIC,X86-32] Advanced Programmable Interrupt Controller
362 Change the output verbosity whilst booting
363 Format: { quiet (default) | verbose | debug }
364 Change the amount of debugging information output
365 when initialising the APIC and IO-APIC components.
368 See Documentation/networking/ipv6.txt.
370 show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller
371 Limit apic dumping. The parameter defines the maximal
372 number of local apics being dumped. Also it is possible
373 to set it to "all" by meaning -- no limit here.
374 Format: { 1 (default) | 2 | ... | all }.
375 The parameter valid if only apic=debug or
376 apic=verbose is specified.
377 Example: apic=debug show_lapic=all
379 apm= [APM] Advanced Power Management
380 See header of arch/x86/kernel/apm_32.c.
382 arcrimi= [HW,NET] ARCnet - "RIM I" (entirely mem-mapped) cards
383 Format: <io>,<irq>,<nodeID>
387 atarimouse= [HW,MOUSE] Atari Mouse
389 atkbd.extra= [HW] Enable extra LEDs and keys on IBM RapidAccess,
390 EzKey and similar keyboards
392 atkbd.reset= [HW] Reset keyboard during initialization
394 atkbd.set= [HW] Select keyboard code set
395 Format: <int> (2 = AT (default), 3 = PS/2)
397 atkbd.scroll= [HW] Enable scroll wheel on MS Office and similar
400 atkbd.softraw= [HW] Choose between synthetic and real raw mode
401 Format: <bool> (0 = real, 1 = synthetic (default))
403 atkbd.softrepeat= [HW]
404 Use software keyboard repeat
406 baycom_epp= [HW,AX25]
409 baycom_par= [HW,AX25] BayCom Parallel Port AX.25 Modem
411 See header of drivers/net/hamradio/baycom_par.c.
413 baycom_ser_fdx= [HW,AX25]
414 BayCom Serial Port AX.25 Modem (Full Duplex Mode)
415 Format: <io>,<irq>,<mode>[,<baud>]
416 See header of drivers/net/hamradio/baycom_ser_fdx.c.
418 baycom_ser_hdx= [HW,AX25]
419 BayCom Serial Port AX.25 Modem (Half Duplex Mode)
420 Format: <io>,<irq>,<mode>
421 See header of drivers/net/hamradio/baycom_ser_hdx.c.
423 boot_delay= Milliseconds to delay each printk during boot.
424 Values larger than 10 seconds (10000) are changed to
428 bootmem_debug [KNL] Enable bootmem allocator debug messages.
430 bttv.card= [HW,V4L] bttv (bt848 + bt878 based grabber cards)
431 bttv.radio= Most important insmod options are available as
433 bttv.pll= See Documentation/video4linux/bttv/Insmod-options
436 bulk_remove=off [PPC] This parameter disables the use of the pSeries
437 firmware feature for flushing multiple hpte entries
440 c101= [NET] Moxa C101 synchronous serial card
442 cachesize= [BUGS=X86-32] Override level 2 CPU cache size detection.
443 Sometimes CPU hardware bugs make them report the cache
444 size incorrectly. The kernel will attempt work arounds
445 to fix known problems, but for some CPUs it is not
446 possible to determine what the correct size should be.
447 This option provides an override for these situations.
450 [SECURITY] Disable capabilities. This would normally
451 be used only if an alternative security model is to be
452 configured. Potentially dangerous and should only be
453 used if you are entirely sure of the consequences.
455 ccw_timeout_log [S390]
456 See Documentation/s390/CommonIO for details.
458 cgroup_disable= [KNL] Disable a particular controller
459 Format: {name of the controller(s) to disable}
460 {Currently supported controllers - "memory"}
462 checkreqprot [SELINUX] Set initial checkreqprot flag value.
463 Format: { "0" | "1" }
464 See security/selinux/Kconfig help text.
465 0 -- check protection applied by kernel (includes
466 any implied execute protection).
467 1 -- check protection requested by application.
468 Default value is set via a kernel config option.
469 Value can be changed at runtime via
470 /selinux/checkreqprot.
473 See Documentation/s390/CommonIO for details.
475 clock= [BUGS=X86-32, HW] gettimeofday clocksource override.
477 Forces specified clocksource (if available) to be used
478 when calculating gettimeofday(). If specified
479 clocksource is not available, it defaults to PIT.
480 Format: { pit | tsc | cyclone | pmtmr }
482 clocksource= Override the default clocksource
484 Override the default clocksource and use the clocksource
485 with the name specified.
486 Some clocksource names to choose from, depending on
488 [all] jiffies (this is the base, fallback clocksource)
490 [ARM] imx_timer1,OSTS,netx_timer,mpu_timer2,
491 pxa_timer,timer3,32k_counter,timer0_1
493 [X86-32] pit,hpet,tsc;
494 scx200_hrt on Geode; cyclone on IBM x440
502 clearcpuid=BITNUM [X86]
503 Disable CPUID feature X for the kernel. See
504 arch/x86/include/asm/cpufeature.h for the valid bit
505 numbers. Note the Linux specific bits are not necessarily
506 stable over kernel options, but the vendor specific
508 Also note that user programs calling CPUID directly
509 or using the feature without checking anything
510 will still see it. This just prevents it from
511 being used by the kernel or shown in /proc/cpuinfo.
512 Also note the kernel might malfunction if you disable
516 Sets the size of kernel global memory area for contiguous
517 memory allocations. For more information, see
518 include/linux/dma-contiguous.h
520 cmo_free_hint= [PPC] Format: { yes | no }
521 Specify whether pages are marked as being inactive
522 when they are freed. This is used in CMO environments
523 to determine OS memory pressure for page stealing by
527 coherent_pool=nn[KMG] [ARM,KNL]
528 Sets the size of memory pool for coherent, atomic dma
529 allocations, by default set to 256K.
531 code_bytes [X86] How many bytes of object code to print
536 com20020= [HW,NET] ARCnet - COM20020 chipset
538 <io>[,<irq>[,<nodeID>[,<backplane>[,<ckp>[,<timeout>]]]]]
540 com90io= [HW,NET] ARCnet - COM90xx chipset (IO-mapped buffers)
544 ARCnet - COM90xx chipset (memory-mapped buffers)
545 Format: <io>[,<irq>[,<memstart>]]
547 condev= [HW,S390] console device
550 console= [KNL] Output console device and options.
552 tty<n> Use the virtual console device <n>.
556 Use the specified serial port. The options are of
557 the form "bbbbpnf", where "bbbb" is the baud rate,
558 "p" is parity ("n", "o", or "e"), "n" is number of
559 bits, and "f" is flow control ("r" for RTS or
560 omit it). Default is "9600n8".
562 See Documentation/serial-console.txt for more
564 Documentation/networking/netconsole.txt for an
567 uart[8250],io,<addr>[,options]
568 uart[8250],mmio,<addr>[,options]
569 Start an early, polled-mode console on the 8250/16550
570 UART at the specified I/O port or MMIO address,
571 switching to the matching ttyS device later. The
572 options are the same as for ttyS, above.
574 If the device connected to the port is not a TTY but a braille
575 device, prepend "brl," before the device type, for instance
577 For now, only VisioBraille is supported.
579 consoleblank= [KNL] The console blank (screen saver) timeout in
580 seconds. Defaults to 10*60 = 10mins. A value of 0
581 disables the blank timer.
584 [KNL] Change the default value for
585 /proc/<pid>/coredump_filter.
586 See also Documentation/filesystems/proc.txt.
588 cpuidle.off=1 [CPU_IDLE]
589 disable the cpuidle sub-system
591 cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver
593 <first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
595 crashkernel=size[KMG][@offset[KMG]]
596 [KNL] Using kexec, Linux can switch to a 'crash kernel'
597 upon panic. This parameter reserves the physical
598 memory region [offset, offset + size] for that kernel
599 image. If '@offset' is omitted, then a suitable offset
600 is selected automatically. Check
601 Documentation/kdump/kdump.txt for further details.
603 crashkernel=range1:size1[,range2:size2,...][@offset]
604 [KNL] Same as above, but depends on the memory
605 in the running system. The syntax of range is
606 start-[end] where start and end are both
607 a memory unit (amount[KMG]). See also
608 Documentation/kdump/kdump.txt for an example.
613 cs89x0_media= [HW,NET]
614 Format: { rj45 | aui | bnc }
617 See header of drivers/s390/block/dasd_devmap.c.
619 db9.dev[2|3]= [HW,JOY] Multisystem joystick support via parallel port
620 (one device per port)
621 Format: <port#>,<type>
622 See also Documentation/input/joystick-parport.txt
624 ddebug_query= [KNL,DYNAMIC_DEBUG] Enable debug messages at early boot
625 time. See Documentation/dynamic-debug-howto.txt for
626 details. Deprecated, see dyndbg.
628 debug [KNL] Enable kernel debugging (events log level).
631 [KNL] verbose self-tests
633 Print debugging info while doing the locking API
635 We default to 0 (no extra messages), setting it to
636 1 will print _a lot_ more information - normally
637 only useful to kernel developers.
639 debug_objects [KNL] Enable object debugging
642 [KNL] Disable object debugging
644 debug_guardpage_minorder=
645 [KNL] When CONFIG_DEBUG_PAGEALLOC is set, this
646 parameter allows control of the order of pages that will
647 be intentionally kept free (and hence protected) by the
648 buddy allocator. Bigger value increase the probability
649 of catching random memory corruption, but reduce the
650 amount of memory for normal system use. The maximum
651 possible value is MAX_ORDER/2. Setting this parameter
652 to 1 or 2 should be enough to identify most random
653 memory corruption problems caused by bugs in kernel or
654 driver code when a CPU writes to (or reads from) a
655 random memory location. Note that there exists a class
656 of memory corruptions problems caused by buggy H/W or
657 F/W or by drivers badly programing DMA (basically when
658 memory is written at bus level and the CPU MMU is
659 bypassed) which are not detectable by
660 CONFIG_DEBUG_PAGEALLOC, hence this option will not help
661 tracking down these problems.
663 debugpat [X86] Enable PAT debugging
665 decnet.addr= [HW,NET]
666 Format: <area>[,<node>]
667 See also Documentation/networking/decnet.txt.
670 [same as hugepagesz=] The size of the default
671 HugeTLB page size. This is the size represented by
672 the legacy /proc/ hugepages APIs, used for SHM, and
673 default size when mounting hugetlbfs filesystems.
674 Defaults to the default architecture's huge page size
678 Set number of hash buckets for dentry cache.
681 IO parameters + enable/disable command.
683 digiepca= [HW,SERIAL]
684 See drivers/char/README.epca and
685 Documentation/serial/digiepca.txt.
688 See Documentation/networking/ipv6.txt.
690 disable_ddw [PPC/PSERIES]
691 Disable Dynamic DMA Window support. Use this if
692 to workaround buggy firmware.
695 See Documentation/networking/ipv6.txt.
697 disable_mtrr_cleanup [X86]
698 The kernel tries to adjust MTRR layout from continuous
699 to discrete, to make X server driver able to add WB
700 entry later. This parameter disables that.
702 disable_mtrr_trim [X86, Intel and AMD only]
703 By default the kernel will trim any uncacheable
704 memory out of your available memory pool based on
705 MTRR settings. This parameter disables that behavior,
706 possibly causing your machine to run very slowly.
708 disable_timer_pin_1 [X86]
709 Disable PIN 1 of APIC timer
710 Can be useful to work around chipset bugs.
712 dma_debug=off If the kernel is compiled with DMA_API_DEBUG support,
713 this option disables the debugging code at boot.
715 dma_debug_entries=<number>
716 This option allows to tune the number of preallocated
717 entries for DMA-API debugging code. One entry is
718 required per DMA-API allocation. Use this if the
719 DMA-API debugging code disables itself because the
720 architectural default is too low.
722 dma_debug_driver=<driver_name>
723 With this option the DMA-API debugging driver
724 filter feature can be enabled at boot time. Just
725 pass the driver to filter for as the parameter.
726 The filter can be disabled or changed to another
727 driver later using sysfs.
729 drm_kms_helper.edid_firmware=[<connector>:]<file>
730 Broken monitors, graphic adapters and KVMs may
731 send no or incorrect EDID data sets. This parameter
732 allows to specify an EDID data set in the
733 /lib/firmware directory that is used instead.
734 Generic built-in EDID data sets are used, if one of
735 edid/1024x768.bin, edid/1280x1024.bin,
736 edid/1680x1050.bin, or edid/1920x1080.bin is given
737 and no file with the same name exists. Details and
738 instructions how to build your own EDID data are
739 available in Documentation/EDID/HOWTO.txt. An EDID
740 data set will only be used for a particular connector,
741 if its name and a colon are prepended to the EDID
746 dyndbg[="val"] [KNL,DYNAMIC_DEBUG]
747 module.dyndbg[="val"]
748 Enable debug messages at boot time. See
749 Documentation/dynamic-debug-howto.txt for details.
751 earlycon= [KNL] Output early console device and options.
752 uart[8250],io,<addr>[,options]
753 uart[8250],mmio,<addr>[,options]
754 uart[8250],mmio32,<addr>[,options]
755 Start an early, polled-mode console on the 8250/16550
756 UART at the specified I/O port or MMIO address.
757 MMIO inter-register address stride is either 8-bit
758 (mmio) or 32-bit (mmio32).
759 The options are the same as for ttyS, above.
761 earlyprintk= [X86,SH,BLACKFIN]
763 earlyprintk=serial[,ttySn[,baudrate]]
764 earlyprintk=ttySn[,baudrate]
765 earlyprintk=dbgp[debugController#]
767 Append ",keep" to not disable it when the real console
770 Only vga or serial or usb debug port at a time.
772 Currently only ttyS0 and ttyS1 are supported.
774 Interaction with the standard serial driver is not
777 The VGA output is eventually overwritten by the real
780 ekgdboc= [X86,KGDB] Allow early kernel console debugging
783 This is designed to be used in conjunction with
784 the boot argument: earlyprintk=vga
787 Format: {"off" | "on" | "skip[mbr]"}
789 eisa_irq_edge= [PARISC,HW]
790 See header of drivers/parisc/eisa.c.
793 See comment before function elanfreq_setup() in
794 arch/x86/kernel/cpu/cpufreq/elanfreq.c.
797 Format: {"cfq" | "deadline" | "noop"}
798 See Documentation/block/cfq-iosched.txt and
799 Documentation/block/deadline-iosched.txt for details.
801 elfcorehdr=[size[KMG]@]offset[KMG] [IA64,PPC,SH,X86,S390]
802 Specifies physical address of start of kernel core
803 image elf header and optionally the size. Generally
804 kexec loader will pass this option to capture kernel.
805 See Documentation/kdump/kdump.txt for details.
807 enable_mtrr_cleanup [X86]
808 The kernel tries to adjust MTRR layout from continuous
809 to discrete, to make X server driver able to add WB
810 entry later. This parameter enables that.
812 enable_timer_pin_1 [X86]
813 Enable PIN 1 of APIC timer
814 Can be useful to work around chipset bugs
815 (in particular on some ATI chipsets).
816 The kernel tries to set a reasonable default.
818 enforcing [SELINUX] Set initial enforcing status.
820 See security/selinux/Kconfig help text.
821 0 -- permissive (log only, no denials).
822 1 -- enforcing (deny and log).
824 Value can be changed at runtime via /selinux/enforce.
827 Disable Error Record Serialization Table (ERST)
830 ether= [HW,NET] Ethernet cards parameters
831 This option is obsoleted by the "netdev=" option, which
832 has equivalent usage. See its documentation for details.
836 Permit 'security.evm' to be updated regardless of
837 current integrity status.
841 fail_make_request=[KNL]
842 General fault injection mechanism.
843 Format: <interval>,<probability>,<space>,<times>
844 See also Documentation/fault-injection/.
847 See Documentation/blockdev/floppy.txt.
849 force_pal_cache_flush
850 [IA-64] Avoid check_sal_cache_flush which may hang on
851 buggy SAL_CACHE_FLUSH implementations. Using this
852 parameter will force ia64_sal_cache_flush to call
853 ia64_pal_cache_flush instead of SAL_CACHE_FLUSH.
856 [FTRACE] will set and start the specified tracer
857 as early as possible in order to facilitate early
860 ftrace_dump_on_oops[=orig_cpu]
861 [FTRACE] will dump the trace buffers on oops.
862 If no parameter is passed, ftrace will dump
863 buffers of all CPUs, but if you pass orig_cpu, it will
864 dump only the buffer of the CPU that triggered the
867 ftrace_filter=[function-list]
868 [FTRACE] Limit the functions traced by the function
869 tracer at boot up. function-list is a comma separated
870 list of functions. This list can be changed at run
871 time by the set_ftrace_filter file in the debugfs
874 ftrace_notrace=[function-list]
875 [FTRACE] Do not trace the functions specified in
876 function-list. This list can be changed at run time
877 by the set_ftrace_notrace file in the debugfs
880 ftrace_graph_filter=[function-list]
881 [FTRACE] Limit the top level callers functions traced
882 by the function graph tracer at boot up.
883 function-list is a comma separated list of functions
884 that can be changed at run time by the
885 set_graph_function file in the debugfs tracing directory.
888 [HW,JOY] Multisystem joystick and NES/SNES/PSX pad
889 support via parallel port (up to 5 devices per port)
890 Format: <port#>,<pad1>,<pad2>,<pad3>,<pad4>,<pad5>
891 See also Documentation/input/joystick-parport.txt
895 gart_fix_e820= [X86_64] disable the fix e820 for K8 GART
899 gcov_persist= [GCOV] When non-zero (default), profiling data for
900 kernel modules is saved and remains accessible via
901 debugfs, even when the module is unloaded/reloaded.
902 When zero, profiling data is discarded and associated
903 debugfs files are removed at module unload time.
905 gpt [EFI] Forces disk with valid GPT signature but
906 invalid Protective MBR to be treated as GPT.
908 grcan.enable0= [HW] Configuration of physical interface 0. Determines
909 the "Enable 0" bit of the configuration register.
912 grcan.enable1= [HW] Configuration of physical interface 1. Determines
913 the "Enable 0" bit of the configuration register.
916 grcan.select= [HW] Select which physical interface to use.
919 grcan.txsize= [HW] Sets the size of the tx buffer.
920 Format: <unsigned int> such that (txsize & ~0x1fffc0) == 0.
922 grcan.rxsize= [HW] Sets the size of the rx buffer.
923 Format: <unsigned int> such that (rxsize & ~0x1fffc0) == 0.
926 hashdist= [KNL,NUMA] Large hashes allocated during boot
927 are distributed across NUMA nodes. Defaults on
928 for 64-bit NUMA, off otherwise.
929 Format: 0 | 1 (for off | on)
931 hcl= [IA-64] SGI's Hardware Graph compatibility layer
933 hd= [EIDE] (E)IDE hard drive subsystem geometry
934 Format: <cyl>,<head>,<sect>
937 Disable Hardware Error Source Table (HEST) support;
938 corresponding firmware-first mode error processing
939 logic will be disabled.
941 highmem=nn[KMG] [KNL,BOOT] forces the highmem zone to have an exact
942 size of <nn>. This works even on boxes that have no
943 highmem otherwise. This also works to reduce highmem
944 size on bigger boxes.
946 highres= [KNL] Enable/disable high resolution timer mode.
947 Valid parameters: "on", "off"
951 See Documentation/isdn/README.HiSax.
955 hpet= [X86-32,HPET] option to control HPET usage
956 Format: { enable (default) | disable | force |
958 disable: disable HPET and use PIT instead
959 force: allow force enabled of undocumented chips (ICH4,
961 verbose: show contents of HPET registers during setup
963 hugepages= [HW,X86-32,IA-64] HugeTLB pages to allocate at boot.
964 hugepagesz= [HW,IA-64,PPC,X86-64] The size of the HugeTLB pages.
965 On x86-64 and powerpc, this option can be specified
966 multiple times interleaved with hugepages= to reserve
967 huge pages of different sizes. Valid pages sizes on
968 x86-64 are 2M (when the CPU supports "pse") and 1G
969 (when the CPU supports the "pdpe1gb" cpuinfo flag)
970 Note that 1GB pages can only be allocated at boot time
971 using hugepages= and not freed afterwards.
973 hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC)
974 terminal devices. Valid values: 0..8
975 hvc_iucv_allow= [S390] Comma-separated list of z/VM user IDs.
976 If specified, z/VM IUCV HVC accepts connections
977 from listed z/VM user IDs only.
980 Do not unregister boot console at start. This is only
981 useful for debugging when something happens in the window
982 between unregistering the boot console and initializing
985 i2c_bus= [HW] Override the default board specific I2C bus speed
986 or register an additional I2C bus that is not
987 registered from board initialization code.
991 i8042.debug [HW] Toggle i8042 debug mode
992 i8042.direct [HW] Put keyboard port into non-translated mode
993 i8042.dumbkbd [HW] Pretend that controller can only read data from
994 keyboard and cannot control its state
995 (Don't attempt to blink the leds)
996 i8042.noaux [HW] Don't check for auxiliary (== mouse) port
997 i8042.nokbd [HW] Don't check/create keyboard port
998 i8042.noloop [HW] Disable the AUX Loopback command while probing
1000 i8042.nomux [HW] Don't check presence of an active multiplexing
1002 i8042.nopnp [HW] Don't use ACPIPnP / PnPBIOS to discover KBD/AUX
1004 i8042.notimeout [HW] Ignore timeout condition signalled by controller
1005 i8042.reset [HW] Reset the controller during init and cleanup
1006 i8042.unlock [HW] Unlock (ignore) the keylock
1010 i8k.ignore_dmi [HW] Continue probing hardware even if DMI data
1011 indicates that the driver is running on unsupported
1013 i8k.force [HW] Activate i8k driver even if SMM BIOS signature
1014 does not match list of supported models.
1016 [HW] Report power status in /proc/i8k
1017 (disabled by default)
1018 i8k.restricted [HW] Allow controlling fans only if SYS_ADMIN
1021 i915.invert_brightness=
1022 [DRM] Invert the sense of the variable that is used to
1023 set the brightness of the panel backlight. Normally a
1024 brightness value of 0 indicates backlight switched off,
1025 and the maximum of the brightness value sets the backlight
1026 to maximum brightness. If this parameter is set to 0
1027 (default) and the machine requires it, or this parameter
1028 is set to 1, a brightness value of 0 sets the backlight
1029 to maximum brightness, and the maximum of the brightness
1030 value switches the backlight off.
1031 -1 -- never invert brightness
1032 0 -- machine default
1033 1 -- force brightness inversion
1036 Format: <io>[,<membase>[,<icn_id>[,<icn_id2>]]]
1038 ide-core.nodma= [HW] (E)IDE subsystem
1039 Format: =0.0 to prevent dma on hda, =0.1 hdb =1.0 hdc
1040 .vlb_clock .pci_clock .noflush .nohpa .noprobe .nowerr
1041 .cdrom .chs .ignore_cable are additional options
1042 See Documentation/ide/ide.txt.
1044 ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem
1045 Claim all unknown PCI IDE storage controllers.
1048 Format: idle=poll, idle=mwait, idle=halt, idle=nomwait
1049 Poll forces a polling idle loop that can slightly
1050 improve the performance of waking up a idle CPU, but
1051 will use a lot of power and make the system run hot.
1053 idle=mwait: On systems which support MONITOR/MWAIT but
1054 the kernel chose to not use it because it doesn't save
1055 as much power as a normal idle loop, use the
1056 MONITOR/MWAIT idle loop anyways. Performance should be
1057 the same as idle=poll.
1058 idle=halt: Halt is forced to be used for CPU idle.
1059 In such case C2/C3 won't be used again.
1060 idle=nomwait: Disable mwait for CPU C-states
1062 ignore_loglevel [KNL]
1063 Ignore loglevel setting - this will print /all/
1064 kernel messages to the console. Useful for debugging.
1065 We also add it as printk module parameter, so users
1066 could change it dynamically, usually by
1067 /sys/module/printk/parameters/ignore_loglevel.
1069 ihash_entries= [KNL]
1070 Set number of hash buckets for inode cache.
1072 ima_appraise= [IMA] appraise integrity measurements
1073 Format: { "off" | "enforce" | "fix" }
1076 ima_appraise_tcb [IMA]
1077 The builtin appraise policy appraises all files
1081 Format: { "0" | "1" }
1082 0 -- integrity auditing messages. (Default)
1083 1 -- enable informational integrity auditing messages.
1086 Format: { "sha1" | "md5" }
1090 Load a policy which meets the needs of the Trusted
1091 Computing Base. This means IMA will measure all
1092 programs exec'd, files mmap'd for exec, and all files
1093 opened for read by uid=0.
1097 Run specified binary instead of /sbin/init as init
1100 initcall_debug [KNL] Trace initcalls as they are executed. Useful
1101 for working out where the kernel is dying during
1104 initrd= [BOOT] Specify the location of the initial ramdisk
1106 inport.irq= [HW] Inport (ATI XL and Microsoft) busmouse driver
1109 intel_iommu= [DMAR] Intel IOMMU driver (DMAR) option
1111 Enable intel iommu driver.
1113 Disable intel iommu driver.
1114 igfx_off [Default Off]
1115 By default, gfx is mapped as normal device. If a gfx
1116 device has a dedicated DMAR unit, the DMAR unit is
1117 bypassed by not enabling DMAR with this option. In
1118 this case, gfx device will use physical address for
1121 With this option iommu will not optimize to look
1122 for io virtual address below 32-bit forcing dual
1123 address cycle on pci bus for cards supporting greater
1124 than 32-bit addressing. The default is to look
1125 for translation below 32-bit and if not available
1126 then look in the higher range.
1127 strict [Default Off]
1128 With this option on every unmap_single operation will
1129 result in a hardware IOTLB flush operation as opposed
1130 to batching them for performance.
1131 sp_off [Default Off]
1132 By default, super page will be supported if Intel IOMMU
1133 has the capability. With this option, super page will
1136 intel_idle.max_cstate= [KNL,HW,ACPI,X86]
1137 0 disables intel_idle and fall back on acpi_idle.
1138 1 to 6 specify maximum depth of C-state.
1140 intremap= [X86-64, Intel-IOMMU]
1141 on enable Interrupt Remapping (default)
1142 off disable Interrupt Remapping
1143 nosid disable Source ID checking
1145 BIOS x2APIC opt-out request will be ignored
1147 iomem= Disable strict checking of access to MMIO memory
1148 strict regions from userspace.
1165 io7= [HW] IO7 for Marvel based alpha systems
1166 See comment before marvel_specify_io7 in
1167 arch/alpha/kernel/core_marvel.c.
1169 io_delay= [X86] I/O delay method
1171 Standard port 0x80 based delay
1173 Alternate port 0xed based delay (needed on some systems)
1175 Simple two microseconds delay
1180 See Documentation/filesystems/nfs/nfsroot.txt.
1182 ip2= [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards
1183 See comment before ip2_setup() in
1184 drivers/char/ip2/ip2base.c.
1187 When an interrupt is not handled search all handlers
1188 for it. Intended to get systems with badly broken
1192 When an interrupt is not handled search all handlers
1193 for it. Also check all handlers each timer
1194 interrupt. Intended to get systems with badly broken
1198 Format: <RDP>,<reset>,<pci_scan>,<verbosity>
1200 isolcpus= [KNL,SMP] Isolate CPUs from the general scheduler.
1202 <cpu number>,...,<cpu number>
1204 <cpu number>-<cpu number>
1205 (must be a positive range in ascending order)
1207 <cpu number>,...,<cpu number>-<cpu number>
1209 This option can be used to specify one or more CPUs
1210 to isolate from the general SMP balancing and scheduling
1211 algorithms. You can move a process onto or off an
1212 "isolated" CPU via the CPU affinity syscalls or cpuset.
1213 <cpu number> begins at 0 and the maximum value is
1214 "number of CPUs in system - 1".
1216 This option is the preferred way to isolate CPUs. The
1217 alternative -- manually setting the CPU mask of all
1218 tasks in the system -- can cause problems and
1219 suboptimal load balancer performance.
1223 js= [HW,JOY] Analog joystick
1224 See Documentation/input/joystick.txt.
1228 kernelcore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
1229 specifies the amount of memory usable by the kernel
1230 for non-movable allocations. The requested amount is
1231 spread evenly throughout all nodes in the system. The
1232 remaining memory in each node is used for Movable
1233 pages. In the event, a node is too small to have both
1234 kernelcore and Movable pages, kernelcore pages will
1235 take priority and other nodes will have a larger number
1236 of kernelcore pages. The Movable zone is used for the
1237 allocation of pages that may be reclaimed or moved
1238 by the page migration subsystem. This means that
1239 HugeTLB pages may not be allocated from this zone.
1240 Note that allocations like PTEs-from-HighMem still
1241 use the HighMem zone if it exists, and the Normal
1242 zone if it does not.
1244 kgdbdbgp= [KGDB,HW] kgdb over EHCI usb debug port.
1245 Format: <Controller#>[,poll interval]
1246 The controller # is the number of the ehci usb debug
1247 port as it is probed via PCI. The poll interval is
1248 optional and is the number seconds in between
1249 each poll cycle to the debug port in case you need
1250 the functionality for interrupting the kernel with
1251 gdb or control-c on the dbgp connection. When
1252 not using this parameter you use sysrq-g to break into
1253 the kernel debugger.
1255 kgdboc= [KGDB,HW] kgdb over consoles.
1256 Requires a tty driver that supports console polling,
1257 or a supported polling keyboard driver (non-usb).
1258 Serial only format: <serial_device>[,baud]
1259 keyboard only format: kbd
1260 keyboard and serial format: kbd,<serial_device>[,baud]
1261 Optional Kernel mode setting:
1262 kms, kbd format: kms,kbd
1263 kms, kbd and serial format: kms,kbd,<ser_dev>[,baud]
1265 kgdbwait [KGDB] Stop kernel execution and enter the
1266 kernel debugger at the earliest opportunity.
1268 kmac= [MIPS] korina ethernet MAC address.
1269 Configure the RouterBoard 532 series on-chip
1270 Ethernet adapter MAC address.
1272 kmemleak= [KNL] Boot-time kmemleak enable/disable
1273 Valid arguments: on, off
1276 kstack=N [X86] Print N words from the kernel stack
1279 kvm.ignore_msrs=[KVM] Ignore guest accesses to unhandled MSRs.
1280 Default is 0 (don't ignore, but inject #GP)
1282 kvm.mmu_audit= [KVM] This is a R/W parameter which allows audit
1286 kvm-amd.nested= [KVM,AMD] Allow nested virtualization in KVM/SVM.
1287 Default is 1 (enabled)
1289 kvm-amd.npt= [KVM,AMD] Disable nested paging (virtualized MMU)
1291 Default is 1 (enabled) if in 64-bit or 32-bit PAE mode.
1293 kvm-intel.ept= [KVM,Intel] Disable extended page tables
1294 (virtualized MMU) support on capable Intel chips.
1295 Default is 1 (enabled)
1297 kvm-intel.emulate_invalid_guest_state=
1298 [KVM,Intel] Enable emulation of invalid guest states
1299 Default is 0 (disabled)
1301 kvm-intel.flexpriority=
1302 [KVM,Intel] Disable FlexPriority feature (TPR shadow).
1303 Default is 1 (enabled)
1306 [KVM,Intel] Enable VMX nesting (nVMX).
1307 Default is 0 (disabled)
1309 kvm-intel.unrestricted_guest=
1310 [KVM,Intel] Disable unrestricted guest feature
1311 (virtualized real and unpaged mode) on capable
1312 Intel chips. Default is 1 (enabled)
1314 kvm-intel.vpid= [KVM,Intel] Disable Virtual Processor Identification
1315 feature (tagged TLBs) on capable Intel chips.
1316 Default is 1 (enabled)
1322 lapic [X86-32,APIC] Enable the local APIC even if BIOS
1325 lapic_timer_c2_ok [X86,APIC] trust the local apic timer
1328 libata.dma= [LIBATA] DMA control
1329 libata.dma=0 Disable all PATA and SATA DMA
1330 libata.dma=1 PATA and SATA Disk DMA only
1331 libata.dma=2 ATAPI (CDROM) DMA only
1332 libata.dma=4 Compact Flash DMA only
1333 Combinations also work, so libata.dma=3 enables DMA
1334 for disks and CDROMs, but not CFs.
1336 libata.ignore_hpa= [LIBATA] Ignore HPA limit
1337 libata.ignore_hpa=0 keep BIOS limits (default)
1338 libata.ignore_hpa=1 ignore limits, using full disk
1340 libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume
1344 libata.force= [LIBATA] Force configurations. The format is comma
1345 separated list of "[ID:]VAL" where ID is
1346 PORT[.DEVICE]. PORT and DEVICE are decimal numbers
1347 matching port, link or device. Basically, it matches
1348 the ATA ID string printed on console by libata. If
1349 the whole ID part is omitted, the last PORT and DEVICE
1350 values are used. If ID hasn't been specified yet, the
1351 configuration applies to all ports, links and devices.
1353 If only DEVICE is omitted, the parameter applies to
1354 the port and all links and devices behind it. DEVICE
1355 number of 0 either selects the first device or the
1356 first fan-out link behind PMP device. It does not
1357 select the host link. DEVICE number of 15 selects the
1358 host link and device attached to it.
1360 The VAL specifies the configuration to force. As long
1361 as there's no ambiguity shortcut notation is allowed.
1362 For example, both 1.5 and 1.5G would work for 1.5Gbps.
1363 The following configurations can be forced.
1365 * Cable type: 40c, 80c, short40c, unk, ign or sata.
1366 Any ID with matching PORT is used.
1368 * SATA link speed limit: 1.5Gbps or 3.0Gbps.
1370 * Transfer mode: pio[0-7], mwdma[0-4] and udma[0-7].
1371 udma[/][16,25,33,44,66,100,133] notation is also
1374 * [no]ncq: Turn on or off NCQ.
1376 * nohrst, nosrst, norst: suppress hard, soft
1379 * rstonce: only attempt one reset during
1380 hot-unplug link recovery
1382 * dump_id: dump IDENTIFY data.
1384 If there are multiple matching configurations changing
1385 the same attribute, the last one is used.
1387 memblock=debug [KNL] Enable memblock debug messages.
1389 load_ramdisk= [RAM] List of ramdisks to load from floppy
1390 See Documentation/blockdev/ramdisk.txt.
1392 lockd.nlm_grace_period=P [NFS] Assign grace period.
1395 lockd.nlm_tcpport=N [NFS] Assign TCP port.
1398 lockd.nlm_timeout=T [NFS] Assign timeout value.
1401 lockd.nlm_udpport=M [NFS] Assign UDP port.
1404 logibm.irq= [HW,MOUSE] Logitech Bus Mouse Driver
1407 loglevel= All Kernel Messages with a loglevel smaller than the
1408 console loglevel will be printed to the console. It can
1409 also be changed with klogd or other programs. The
1410 loglevels are defined as follows:
1412 0 (KERN_EMERG) system is unusable
1413 1 (KERN_ALERT) action must be taken immediately
1414 2 (KERN_CRIT) critical conditions
1415 3 (KERN_ERR) error conditions
1416 4 (KERN_WARNING) warning conditions
1417 5 (KERN_NOTICE) normal but significant condition
1418 6 (KERN_INFO) informational
1419 7 (KERN_DEBUG) debug-level messages
1421 log_buf_len=n[KMG] Sets the size of the printk ring buffer,
1422 in bytes. n must be a power of two. The default
1423 size is set in the kernel config file.
1425 logo.nologo [FB] Disables display of the built-in Linux logo.
1426 This may be used to provide more screen space for
1427 kernel log messages and is useful when debugging
1428 kernel boot problems.
1430 lp=0 [LP] Specify parallel ports to use, e.g,
1431 lp=port[,port...] lp=none,parport0 (lp0 not configured, lp1 uses
1432 lp=reset first parallel port). 'lp=0' disables the
1433 lp=auto printer driver. 'lp=reset' (which can be
1434 specified in addition to the ports) causes
1435 attached printers to be reset. Using
1436 lp=port1,port2,... specifies the parallel ports
1437 to associate lp devices with, starting with
1438 lp0. A port specification may be 'none' to skip
1439 that lp device, or a parport name such as
1440 'parport0'. Specifying 'lp=auto' instead of a
1441 port specification list means that device IDs
1442 from each port should be examined, to see if
1443 an IEEE 1284-compliant printer is attached; if
1444 so, the driver will manage that printer.
1445 See also header of drivers/char/lp.c.
1448 Sets loops_per_jiffy to given constant, thus avoiding
1449 time-consuming boot-time autodetection (up to 250 ms per
1450 CPU). 0 enables autodetection (default). To determine
1451 the correct value for your kernel, boot with normal
1452 autodetection and see what value is printed. Note that
1453 on SMP systems the preset will be applied to all CPUs,
1454 which is likely to cause problems if your CPUs need
1455 significantly divergent settings. An incorrect value
1456 will cause delays in the kernel to be wrong, leading to
1457 unpredictable I/O errors and other breakage. Although
1458 unlikely, in the extreme case this might damage your
1462 Format: <io>,<irq>,<dma>
1464 machvec= [IA-64] Force the use of a particular machine-vector
1465 (machvec) in a generic kernel.
1466 Example: machvec=hpzx1_swiotlb
1468 machtype= [Loongson] Share the same kernel image file between different
1470 Example: machtype=lemote-yeeloong-2f-7inch
1472 max_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory greater
1473 than or equal to this physical address is ignored.
1475 maxcpus= [SMP] Maximum number of processors that an SMP kernel
1476 should make use of. maxcpus=n : n >= 0 limits the
1477 kernel to using 'n' processors. n=0 is a special case,
1478 it is equivalent to "nosmp", which also disables
1481 max_loop= [LOOP] The number of loop block devices that get
1482 (loop.max_loop) unconditionally pre-created at init time. The default
1483 number is configured by BLK_DEV_LOOP_MIN_COUNT. Instead
1484 of statically allocating a predefined number, loop
1485 devices can be requested on-demand with the
1486 /dev/loop-control interface.
1488 mce [X86-32] Machine Check Exception
1490 mce=option [X86-64] See Documentation/x86/x86_64/boot-options.txt
1492 md= [HW] RAID subsystems devices and level
1493 See Documentation/md.txt.
1496 Format: <first>,<last>
1497 Specifies range of consoles to be captured by the MDA.
1499 mem=nn[KMG] [KNL,BOOT] Force usage of a specific amount of memory
1500 Amount of memory to be used when the kernel is not able
1501 to see the whole system memory or for test.
1502 [X86-32] Use together with memmap= to avoid physical
1503 address space collisions. Without memmap= PCI devices
1504 could be placed at addresses belonging to unused RAM.
1506 mem=nopentium [BUGS=X86-32] Disable usage of 4MB pages for kernel
1510 [KNL,SH] Allow user to override the default size for
1511 per-device physically contiguous DMA buffers.
1513 memmap=exactmap [KNL,X86] Enable setting of an exact
1514 E820 memory map, as specified by the user.
1515 Such memmap=exactmap lines can be constructed based on
1516 BIOS output or other requirements. See the memmap=nn@ss
1519 memmap=nn[KMG]@ss[KMG]
1520 [KNL] Force usage of a specific region of memory
1521 Region of memory to be used, from ss to ss+nn.
1523 memmap=nn[KMG]#ss[KMG]
1524 [KNL,ACPI] Mark specific memory as ACPI data.
1525 Region of memory to be used, from ss to ss+nn.
1527 memmap=nn[KMG]$ss[KMG]
1528 [KNL,ACPI] Mark specific memory as reserved.
1529 Region of memory to be used, from ss to ss+nn.
1530 Example: Exclude memory from 0x18690000-0x1869ffff
1531 memmap=64K$0x18690000
1533 memmap=0x10000$0x18690000
1535 memory_corruption_check=0/1 [X86]
1536 Some BIOSes seem to corrupt the first 64k of
1537 memory when doing things like suspend/resume.
1538 Setting this option will scan the memory
1539 looking for corruption. Enabling this will
1540 both detect corruption and prevent the kernel
1541 from using the memory being corrupted.
1542 However, its intended as a diagnostic tool; if
1543 repeatable BIOS-originated corruption always
1544 affects the same memory, you can use memmap=
1545 to prevent the kernel from using that memory.
1547 memory_corruption_check_size=size [X86]
1548 By default it checks for corruption in the low
1549 64k, making this memory unavailable for normal
1550 use. Use this parameter to scan for
1551 corruption in more or less memory.
1553 memory_corruption_check_period=seconds [X86]
1554 By default it checks for corruption every 60
1555 seconds. Use this parameter to check at some
1556 other rate. 0 disables periodic checking.
1558 memtest= [KNL,X86] Enable memtest
1560 default : 0 <disable>
1561 Specifies the number of memtest passes to be
1562 performed. Each pass selects another test
1563 pattern from a given set of patterns. Memtest
1564 fills the memory with this pattern, validates
1565 memory contents and reserves bad memory
1566 regions that are detected.
1568 meye.*= [HW] Set MotionEye Camera parameters
1569 See Documentation/video4linux/meye.txt.
1571 mfgpt_irq= [IA-32] Specify the IRQ to use for the
1572 Multi-Function General Purpose Timers on AMD Geode
1575 mfgptfix [X86-32] Fix MFGPT timers on AMD Geode platforms when
1576 the BIOS has incorrectly applied a workaround. TinyBIOS
1577 version 0.98 is known to be affected, 0.99 fixes the
1578 problem by letting the user disable the workaround.
1582 min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this
1583 physical address is ignored.
1585 mini2440= [ARM,HW,KNL]
1586 Format:[0..2][b][c][t]
1588 MINI2440 configuration specification:
1589 0 - The attached screen is the 3.5" TFT
1590 1 - The attached screen is the 7" TFT
1591 2 - The VGA Shield is attached (1024x768)
1592 Leaving out the screen size parameter will not load
1593 the TFT driver, and the framebuffer will be left
1595 b - Enable backlight. The TFT backlight pin will be
1596 linked to the kernel VESA blanking code and a GPIO
1597 LED. This parameter is not necessary when using the
1599 c - Enable the s3c camera interface.
1600 t - Reserved for enabling touchscreen support. The
1601 touchscreen support is not enabled in the mainstream
1602 kernel as of 2.6.30, a preliminary port can be found
1603 in the "bleeding edge" mini2440 support kernel at
1604 http://repo.or.cz/w/linux-2.6/mini2440.git
1607 [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
1608 parameter allows control of the logging verbosity for
1609 the additional memory initialisation checks. A value
1610 of 0 disables mminit logging and a level of 4 will
1611 log everything. Information is printed at KERN_DEBUG
1612 so loglevel=8 may also need to be specified.
1615 [KNL] When CONFIG_MODULE_SIG is set, this means that
1616 modules without (valid) signatures will fail to load.
1617 Note that if CONFIG_MODULE_SIG_ENFORCE is set, that
1618 is always true, so this option does nothing.
1621 [MOUSE] Maximum time between finger touching and
1622 leaving touchpad surface for touch to be considered
1623 a tap and be reported as a left button click (for
1624 touchpads working in absolute mode only).
1626 mousedev.xres= [MOUSE] Horizontal screen resolution, used for devices
1627 reporting absolute coordinates, such as tablets
1628 mousedev.yres= [MOUSE] Vertical screen resolution, used for devices
1629 reporting absolute coordinates, such as tablets
1631 movablecore=nn[KMG] [KNL,X86,IA-64,PPC] This parameter
1632 is similar to kernelcore except it specifies the
1633 amount of memory used for migratable allocations.
1634 If both kernelcore and movablecore is specified,
1635 then kernelcore will be at *least* the specified
1636 value but may be more. If movablecore on its own
1637 is specified, the administrator must be careful
1638 that the amount of memory usable for all allocations
1641 MTD_Partition= [MTD]
1642 Format: <name>,<region-number>,<size>,<offset>
1644 MTD_Region= [MTD] Format:
1645 <name>,<region-number>[,<base>,<size>,<buswidth>,<altbuswidth>]
1648 See drivers/mtd/cmdlinepart.c.
1650 multitce=off [PPC] This parameter disables the use of the pSeries
1651 firmware feature for updating multiple TCE entries
1654 onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration
1656 Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock]
1658 boundary - index of last SLC block on Flex-OneNAND.
1659 The remaining blocks are configured as MLC blocks.
1660 lock - Configure if Flex-OneNAND boundary should be locked.
1661 Once locked, the boundary cannot be changed.
1662 1 indicates lock status, 0 indicates unlock status.
1665 ARM/S3C2412 JIVE boot control
1667 See arch/arm/mach-s3c2412/mach-jive.c
1669 mtouchusb.raw_coordinates=
1670 [HW] Make the MicroTouch USB driver use raw coordinates
1671 ('y', default) or cooked coordinates ('n')
1673 mtrr_chunk_size=nn[KMG] [X86]
1674 used for mtrr cleanup. It is largest continuous chunk
1675 that could hold holes aka. UC entries.
1677 mtrr_gran_size=nn[KMG] [X86]
1678 Used for mtrr cleanup. It is granularity of mtrr block.
1680 Large value could prevent small alignment from
1683 mtrr_spare_reg_nr=n [X86]
1685 Range: 0,7 : spare reg number
1687 Used for mtrr cleanup. It is spare mtrr entries number.
1688 Set to 2 or more if your graphical card needs more.
1690 n2= [NET] SDL Inc. RISCom/N2 synchronous serial card
1692 netdev= [NET] Network devices parameters
1693 Format: <irq>,<io>,<mem_start>,<mem_end>,<name>
1694 Note that mem_start is often overloaded to mean
1695 something different and driver-specific.
1696 This usage is only documented in each driver source
1700 [NETFILTER] Enable connection tracking flow accounting
1701 0 to disable accounting
1702 1 to enable accounting
1705 nfsaddrs= [NFS] Deprecated. Use ip= instead.
1706 See Documentation/filesystems/nfs/nfsroot.txt.
1708 nfsroot= [NFS] nfs root filesystem for disk-less boxes.
1709 See Documentation/filesystems/nfs/nfsroot.txt.
1711 nfsrootdebug [NFS] enable nfsroot debugging messages.
1712 See Documentation/filesystems/nfs/nfsroot.txt.
1714 nfs.callback_tcpport=
1715 [NFS] set the TCP port on which the NFSv4 callback
1716 channel should listen.
1719 [NFS] sets the pathname to the program which is used
1720 to update the NFS client cache entries.
1722 nfs.cache_getent_timeout=
1723 [NFS] sets the timeout after which an attempt to
1724 update a cache entry is deemed to have failed.
1726 nfs.idmap_cache_timeout=
1727 [NFS] set the maximum lifetime for idmapper cache
1731 [NFS] enable 64-bit inode numbers.
1732 If zero, the NFS client will fake up a 32-bit inode
1733 number for the readdir() and stat() syscalls instead
1734 of returning the full 64-bit number.
1735 The default is to return 64-bit inode numbers.
1737 nfs.max_session_slots=
1738 [NFSv4.1] Sets the maximum number of session slots
1739 the client will attempt to negotiate with the server.
1740 This limits the number of simultaneous RPC requests
1741 that the client can send to the NFSv4.1 server.
1742 Note that there is little point in setting this
1743 value higher than the max_tcp_slot_table_limit.
1745 nfs.nfs4_disable_idmapping=
1746 [NFSv4] When set to the default of '1', this option
1747 ensures that both the RPC level authentication
1748 scheme and the NFS level operations agree to use
1749 numeric uids/gids if the mount is using the
1750 'sec=sys' security flavour. In effect it is
1751 disabling idmapping, which can make migration from
1752 legacy NFSv2/v3 systems to NFSv4 easier.
1753 Servers that do not support this mode of operation
1754 will be autodetected by the client, and it will fall
1755 back to using the idmapper.
1756 To turn off this behaviour, set the value to '0'.
1758 [NFS4] Specify an additional fixed unique ident-
1759 ification string that NFSv4 clients can insert into
1760 their nfs_client_id4 string. This is typically a
1761 UUID that is generated at system install time.
1763 nfs.send_implementation_id =
1764 [NFSv4.1] Send client implementation identification
1765 information in exchange_id requests.
1766 If zero, no implementation identification information
1768 The default is to send the implementation identification
1771 nfsd.nfs4_disable_idmapping=
1772 [NFSv4] When set to the default of '1', the NFSv4
1773 server will return only numeric uids and gids to
1774 clients using auth_sys, and will accept numeric uids
1775 and gids from such clients. This is intended to ease
1776 migration from NFSv2/v3.
1778 objlayoutdriver.osd_login_prog=
1779 [NFS] [OBJLAYOUT] sets the pathname to the program which
1780 is used to automatically discover and login into new
1781 osd-targets. Please see:
1782 Documentation/filesystems/pnfs.txt for more explanations
1784 nmi_debug= [KNL,AVR32,SH] Specify one or more actions to take
1785 when a NMI is triggered.
1786 Format: [state][,regs][,debounce][,die]
1788 nmi_watchdog= [KNL,BUGS=X86] Debugging features for SMP kernels
1789 Format: [panic,][nopanic,][num]
1791 0 - turn nmi_watchdog off
1792 When panic is specified, panic when an NMI watchdog
1793 timeout occurs (or 'nopanic' to override the opposite
1795 This is useful when you use a panic=... timeout and
1796 need the box quickly up again.
1798 netpoll.carrier_timeout=
1799 [NET] Specifies amount of time (in seconds) that
1800 netpoll should wait for a carrier. By default netpoll
1803 no387 [BUGS=X86-32] Tells the kernel to use the 387 maths
1804 emulation library even if a 387 maths coprocessor
1808 [HW] Never suspend the console
1809 Disable suspending of consoles during suspend and
1810 hibernate operations. Once disabled, debugging
1811 messages can reach various consoles while the rest
1812 of the system is being put to sleep (ie, while
1813 debugging driver suspend/resume hooks). This may
1814 not work reliably with all consoles, but is known
1815 to work with serial and VGA consoles.
1816 To facilitate more flexible debugging, we also add
1817 console_suspend, a printk module parameter to control
1818 it. Users could use console_suspend (usually
1819 /sys/module/printk/parameters/console_suspend) to
1820 turn on/off it dynamically.
1822 noaliencache [MM, NUMA, SLAB] Disables the allocation of alien
1823 caches in the slab allocator. Saves per-node memory,
1824 but will impact performance.
1828 noapic [SMP,APIC] Tells the kernel to not make use of any
1829 IOAPICs that may be present in the system.
1831 noautogroup Disable scheduler automatic task group creation.
1833 nobats [PPC] Do not use BATs for mapping kernel lowmem
1834 on "Classic" PPC cores.
1838 noclflush [BUGS=X86] Don't use the CLFLUSH instruction
1840 nodelayacct [KNL] Disable per-task delay accounting
1842 nodisconnect [HW,SCSI,M68K] Disables SCSI disconnects.
1844 nodsp [SH] Disable hardware DSP at boot time.
1846 noefi [X86] Disable EFI runtime services support.
1851 On X86-32 available only on PAE configured kernels.
1852 noexec=on: enable non-executable mappings (default)
1853 noexec=off: disable non-executable mappings
1856 Disable SMAP (Supervisor Mode Access Prevention)
1857 even if it is supported by processor.
1860 Disable SMEP (Supervisor Mode Execution Prevention)
1861 even if it is supported by processor.
1864 This affects only 32-bit executables.
1865 noexec32=on: enable non-executable mappings (default)
1866 read doesn't imply executable mappings
1867 noexec32=off: disable non-executable mappings
1868 read implies executable mappings
1870 nofpu [SH] Disable hardware FPU at boot time.
1872 nofxsr [BUGS=X86-32] Disables x86 floating point extended
1873 register save and restore. The kernel will only save
1874 legacy floating-point registers on task switch.
1876 noxsave [BUGS=X86] Disables x86 extended register state save
1877 and restore using xsave. The kernel will fallback to
1878 enabling legacy floating-point and sse state.
1881 on enable eager fpu restore
1882 off disable eager fpu restore
1883 auto selects the default scheme, which automatically
1884 enables eagerfpu restore for xsaveopt.
1886 nohlt [BUGS=ARM,SH] Tells the kernel that the sleep(SH) or
1887 wfi(ARM) instruction doesn't work correctly and not to
1888 use it. This is also useful when using JTAG debugger.
1890 no-hlt [BUGS=X86-32] Tells the kernel that the hlt
1891 instruction doesn't work correctly and not to
1894 no_file_caps Tells the kernel not to honor file capabilities. The
1895 only way then for a file to be executed with privilege
1896 is to be setuid root or executed by root.
1898 nohalt [IA-64] Tells the kernel not to use the power saving
1899 function PAL_HALT_LIGHT when idle. This increases
1900 power-consumption. On the positive side, it reduces
1901 interrupt wake-up latency, which may improve performance
1902 in certain environments such as networked servers or
1905 nohz= [KNL] Boottime enable/disable dynamic ticks
1906 Valid arguments: on, off
1909 noiotrap [SH] Disables trapped I/O port accesses.
1911 noirqdebug [X86-32] Disables the code which attempts to detect and
1912 disable unhandled interrupt sources.
1914 no_timer_check [X86,APIC] Disables the code which tests for
1915 broken timer IRQ sources.
1917 noisapnp [ISAPNP] Disables ISA PnP code.
1919 noinitrd [RAM] Tells the kernel not to load any configured
1922 nointremap [X86-64, Intel-IOMMU] Do not enable interrupt
1924 [Deprecated - use intremap=off]
1928 nojitter [IA-64] Disables jitter checking for ITC timers.
1930 no-kvmclock [X86,KVM] Disable paravirtualized KVM clock driver
1932 no-kvmapf [X86,KVM] Disable paravirtualized asynchronous page
1935 no-steal-acc [X86,KVM] Disable paravirtualized steal time accounting.
1936 steal time is computed, but won't influence scheduler
1939 nolapic [X86-32,APIC] Do not enable or use the local APIC.
1941 nolapic_timer [X86-32,APIC] Do not use the local APIC timer.
1943 noltlbs [PPC] Do not use large page/tlb entries for kernel
1944 lowmem mapping on PPC40x.
1946 nomca [IA-64] Disable machine check abort handling
1948 nomce [X86-32] Machine Check Exception
1950 nomfgpt [X86-32] Disable Multi-Function General Purpose
1951 Timer usage (for AMD Geode machines).
1953 nonmi_ipi [X86] Disable using NMI IPIs during panic/reboot to
1954 shutdown the other cpus. Instead use the REBOOT_VECTOR
1957 nomodule Disable module load
1959 nopat [X86] Disable PAT (page attribute table extension of
1960 pagetables) support.
1962 norandmaps Don't use address space randomization. Equivalent to
1963 echo 0 > /proc/sys/kernel/randomize_va_space
1965 noreplace-paravirt [X86,IA-64,PV_OPS] Don't patch paravirt_ops
1967 noreplace-smp [X86-32,SMP] Don't replace SMP instructions
1968 with UP alternatives
1970 noresidual [PPC] Don't use residual data on PReP machines.
1972 nordrand [X86] Disable the direct use of the RDRAND
1973 instruction even if it is supported by the
1974 processor. RDRAND is still available to user
1977 noresume [SWSUSP] Disables resume and restores original swap
1980 no-scroll [VGA] Disables scrollback.
1981 This is required for the Braillex ib80-piezo Braille
1982 reader made by F.H. Papenmeier (Germany).
1986 nosep [BUGS=X86-32] Disables x86 SYSENTER/SYSEXIT support.
1988 nosmp [SMP] Tells an SMP kernel to act as a UP kernel,
1989 and disable the IO APIC. legacy for "maxcpus=0".
1991 nosoftlockup [KNL] Disable the soft-lockup detector.
1993 nosync [HW,M68K] Disables sync negotiation for all devices.
1995 notsc [BUGS=X86-32] Disable Time Stamp Counter
1997 nousb [USB] Disable the USB subsystem
1999 nowatchdog [KNL] Disable the lockup detector (NMI watchdog).
2003 nox2apic [X86-64,APIC] Do not enable x2APIC mode.
2005 nptcg= [IA-64] Override max number of concurrent global TLB
2006 purges which is reported from either PAL_VM_SUMMARY or
2009 nr_cpus= [SMP] Maximum number of processors that an SMP kernel
2010 could support. nr_cpus=n : n >= 1 limits the kernel to
2011 supporting 'n' processors. Later in runtime you can not
2012 use hotplug cpu feature to put more cpu back to online.
2013 just like you compile the kernel NR_CPUS=n
2015 nr_uarts= [SERIAL] maximum number of UARTs to be registered.
2017 numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA.
2018 one of ['zone', 'node', 'default'] can be specified
2019 This can be set from sysctl after boot.
2020 See Documentation/sysctl/vm.txt for details.
2022 ohci1394_dma=early [HW] enable debugging via the ohci1394 driver.
2023 See Documentation/debugging-via-ohci1394.txt for more
2026 olpc_ec_timeout= [OLPC] ms delay when issuing EC commands
2027 Rather than timing out after 20 ms if an EC
2028 command is not properly ACKed, override the length
2029 of the timeout. We have interrupts disabled while
2030 waiting for the ACK, so if this is set too high
2031 interrupts *may* be lost!
2033 omap_mux= [OMAP] Override bootloader pin multiplexing.
2034 Format: <mux_mode0.mode_name=value>...
2035 For example, to override I2C bus2:
2036 omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100
2038 oprofile.timer= [HW]
2039 Use timer interrupt instead of performance counters
2041 oprofile.cpu_type= Force an oprofile cpu type
2042 This might be useful if you have an older oprofile
2043 userland or if you want common events.
2044 Format: { arch_perfmon }
2045 arch_perfmon: [X86] Force use of architectural
2046 perfmon on Intel CPUs instead of the
2047 CPU specific event set.
2048 timer: [X86] Force use of architectural NMI
2049 timer mode (see also oprofile.timer
2050 for generic hr timer mode)
2051 [s390] Force legacy basic mode sampling
2052 (report cpu_type "timer")
2054 oops=panic Always panic on oopses. Default is to just kill the
2055 process, but there is a small probability of
2056 deadlocking the machine.
2057 This will also cause panics on machine check exceptions.
2058 Useful together with panic=30 to trigger a reboot.
2061 See Documentation/sound/oss/oss-parameters.txt
2063 panic= [KNL] Kernel behaviour on panic: delay <timeout>
2064 timeout > 0: seconds before rebooting
2065 timeout = 0: wait forever
2066 timeout < 0: reboot immediately
2069 parkbd.port= [HW] Parallel port number the keyboard adapter is
2070 connected to, default is 0.
2072 parkbd.mode= [HW] Parallel port keyboard adapter mode of operation,
2073 0 for XT, 1 for AT (default is AT).
2076 parport= [HW,PPT] Specify parallel ports. 0 disables.
2077 Format: { 0 | auto | 0xBBB[,IRQ[,DMA]] }
2078 Use 'auto' to force the driver to use any
2079 IRQ/DMA settings detected (the default is to
2080 ignore detected IRQ/DMA settings because of
2081 possible conflicts). You can specify the base
2082 address, IRQ, and DMA settings; IRQ and DMA
2083 should be numbers, or 'auto' (for using detected
2084 settings on that particular port), or 'nofifo'
2085 (to avoid using a FIFO even if it is detected).
2086 Parallel ports are assigned in the order they
2087 are specified on the command line, starting
2090 parport_init_mode= [HW,PPT]
2091 Configure VIA parallel port to operate in
2092 a specific mode. This is necessary on Pegasos
2093 computer where firmware has no options for setting
2094 up parallel port mode and sets it to spp.
2095 Currently this function knows 686a and 8231 chips.
2096 Format: [spp|ps2|epp|ecp|ecpepp]
2099 Halt all CPUs after the first oops has been printed for
2100 the specified number of seconds. This is to be used if
2101 your oopses keep scrolling off the screen.
2106 See header of drivers/block/paride/pcd.c.
2107 See also Documentation/blockdev/paride.txt.
2109 pci=option[,option...] [PCI] various PCI subsystem options:
2110 earlydump [X86] dump PCI config space before the kernel
2112 off [X86] don't probe for the PCI bus
2113 bios [X86-32] force use of PCI BIOS, don't access
2114 the hardware directly. Use this if your machine
2115 has a non-standard PCI host bridge.
2116 nobios [X86-32] disallow use of PCI BIOS, only direct
2117 hardware access methods are allowed. Use this
2118 if you experience crashes upon bootup and you
2119 suspect they are caused by the BIOS.
2120 conf1 [X86] Force use of PCI Configuration
2122 conf2 [X86] Force use of PCI Configuration
2124 noaer [PCIE] If the PCIEAER kernel config parameter is
2125 enabled, this kernel boot option can be used to
2126 disable the use of PCIE advanced error reporting.
2127 nodomains [PCI] Disable support for multiple PCI
2128 root domains (aka PCI segments, in ACPI-speak).
2129 nommconf [X86] Disable use of MMCONFIG for PCI
2131 check_enable_amd_mmconf [X86] check for and enable
2132 properly configured MMIO access to PCI
2133 config space on AMD family 10h CPU
2134 nomsi [MSI] If the PCI_MSI kernel config parameter is
2135 enabled, this kernel boot option can be used to
2136 disable the use of MSI interrupts system-wide.
2137 noioapicquirk [APIC] Disable all boot interrupt quirks.
2138 Safety option to keep boot IRQs enabled. This
2139 should never be necessary.
2140 ioapicreroute [APIC] Enable rerouting of boot IRQs to the
2141 primary IO-APIC for bridges that cannot disable
2142 boot IRQs. This fixes a source of spurious IRQs
2143 when the system masks IRQs.
2144 noioapicreroute [APIC] Disable workaround that uses the
2145 boot IRQ equivalent of an IRQ that connects to
2146 a chipset where boot IRQs cannot be disabled.
2147 The opposite of ioapicreroute.
2148 biosirq [X86-32] Use PCI BIOS calls to get the interrupt
2149 routing table. These calls are known to be buggy
2150 on several machines and they hang the machine
2151 when used, but on other computers it's the only
2152 way to get the interrupt routing table. Try
2153 this option if the kernel is unable to allocate
2154 IRQs or discover secondary PCI buses on your
2156 rom [X86] Assign address space to expansion ROMs.
2157 Use with caution as certain devices share
2158 address decoders between ROMs and other
2160 norom [X86] Do not assign address space to
2161 expansion ROMs that do not already have
2162 BIOS assigned address ranges.
2163 nobar [X86] Do not assign address space to the
2164 BARs that weren't assigned by the BIOS.
2165 irqmask=0xMMMM [X86] Set a bit mask of IRQs allowed to be
2166 assigned automatically to PCI devices. You can
2167 make the kernel exclude IRQs of your ISA cards
2169 pirqaddr=0xAAAAA [X86] Specify the physical address
2170 of the PIRQ table (normally generated
2171 by the BIOS) if it is outside the
2172 F0000h-100000h range.
2173 lastbus=N [X86] Scan all buses thru bus #N. Can be
2174 useful if the kernel is unable to find your
2175 secondary buses and you want to tell it
2176 explicitly which ones they are.
2177 assign-busses [X86] Always assign all PCI bus
2178 numbers ourselves, overriding
2179 whatever the firmware may have done.
2180 usepirqmask [X86] Honor the possible IRQ mask stored
2181 in the BIOS $PIR table. This is needed on
2182 some systems with broken BIOSes, notably
2183 some HP Pavilion N5400 and Omnibook XE3
2184 notebooks. This will have no effect if ACPI
2185 IRQ routing is enabled.
2186 noacpi [X86] Do not use ACPI for IRQ routing
2187 or for PCI scanning.
2188 use_crs [X86] Use PCI host bridge window information
2189 from ACPI. On BIOSes from 2008 or later, this
2190 is enabled by default. If you need to use this,
2191 please report a bug.
2192 nocrs [X86] Ignore PCI host bridge windows from ACPI.
2193 If you need to use this, please report a bug.
2194 routeirq Do IRQ routing for all PCI devices.
2195 This is normally done in pci_enable_device(),
2196 so this option is a temporary workaround
2197 for broken drivers that don't call it.
2198 skip_isa_align [X86] do not align io start addr, so can
2199 handle more pci cards
2200 firmware [ARM] Do not re-enumerate the bus but instead
2201 just use the configuration from the
2202 bootloader. This is currently used on
2203 IXP2000 systems where the bus has to be
2204 configured a certain way for adjunct CPUs.
2205 noearly [X86] Don't do any early type 1 scanning.
2206 This might help on some broken boards which
2207 machine check when some devices' config space
2208 is read. But various workarounds are disabled
2209 and some IOMMU drivers will not work.
2210 bfsort Sort PCI devices into breadth-first order.
2211 This sorting is done to get a device
2212 order compatible with older (<= 2.4) kernels.
2213 nobfsort Don't sort PCI devices into breadth-first order.
2214 cbiosize=nn[KMG] The fixed amount of bus space which is
2215 reserved for the CardBus bridge's IO window.
2216 The default value is 256 bytes.
2217 cbmemsize=nn[KMG] The fixed amount of bus space which is
2218 reserved for the CardBus bridge's memory
2219 window. The default value is 64 megabytes.
2222 [<order of align>@][<domain>:]<bus>:<slot>.<func>[; ...]
2223 Specifies alignment and device to reassign
2224 aligned memory resources.
2225 If <order of align> is not specified,
2226 PAGE_SIZE is used as alignment.
2227 PCI-PCI bridge can be specified, if resource
2228 windows need to be expanded.
2229 ecrc= Enable/disable PCIe ECRC (transaction layer
2230 end-to-end CRC checking).
2231 bios: Use BIOS/firmware settings. This is the
2235 realloc= Enable/disable reallocating PCI bridge resources
2236 if allocations done by BIOS are too small to
2237 accommodate resources required by all child
2239 off: Turn realloc off
2241 realloc same as realloc=on
2242 noari do not use PCIe ARI.
2243 pcie_scan_all Scan all possible PCIe devices. Otherwise we
2244 only look for one device below a PCIe downstream
2247 pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power
2250 force Enable ASPM even on devices that claim not to support it.
2251 WARNING: Forcing ASPM on may cause system lockups.
2253 pcie_hp= [PCIE] PCI Express Hotplug driver options:
2254 nomsi Do not use MSI for PCI Express Native Hotplug (this
2255 makes all PCIe ports use INTx for hotplug services).
2257 pcie_ports= [PCIE] PCIe ports handling:
2258 auto Ask the BIOS whether or not to use native PCIe services
2259 associated with PCIe ports (PME, hot-plug, AER). Use
2260 them only if that is allowed by the BIOS.
2261 native Use native PCIe services associated with PCIe ports
2263 compat Treat PCIe ports as PCI-to-PCI bridges, disable the PCIe
2266 pcie_pme= [PCIE,PM] Native PCIe PME signaling options:
2267 nomsi Do not use MSI for native PCIe PME signaling (this makes
2268 all PCIe root ports use INTx for all services).
2270 pcmv= [HW,PCMCIA] BadgePAD 4
2273 See Documentation/blockdev/paride.txt.
2275 pdcchassis= [PARISC,HW] Disable/Enable PDC Chassis Status codes at
2278 See arch/parisc/kernel/pdc_chassis.c
2280 percpu_alloc= Select which percpu first chunk allocator to use.
2281 Currently supported values are "embed" and "page".
2282 Archs may support subset or none of the selections.
2283 See comments in mm/percpu.c for details on each
2284 allocator. This parameter is primarily for debugging
2285 and performance comparison.
2288 See Documentation/blockdev/paride.txt.
2291 See Documentation/blockdev/paride.txt.
2293 pirq= [SMP,APIC] Manual mp-table setup
2294 See Documentation/x86/i386/IO-APIC.txt.
2296 plip= [PPT,NET] Parallel port network link
2297 Format: { parport<nr> | timid | 0 }
2298 See also Documentation/parport.txt.
2300 pmtmr= [X86] Manual setup of pmtmr I/O Port.
2301 Override pmtimer IOPort with a hex value.
2305 Enable PNP debug messages (depends on the
2306 CONFIG_PNP_DEBUG_MESSAGES option). Change at run-time
2307 via /sys/module/pnp/parameters/debug. We always show
2308 current resource usage; turning this on also shows
2309 possible settings and some assignment information.
2315 { on | off | curr | res | no-curr | no-res }
2318 [ISAPNP] Exclude IRQs for the autoconfiguration
2321 [ISAPNP] Exclude DMAs for the autoconfiguration
2323 pnp_reserve_io= [ISAPNP] Exclude I/O ports for the autoconfiguration
2324 Ranges are in pairs (I/O port base and size).
2327 [ISAPNP] Exclude memory regions for the
2329 Ranges are in pairs (memory base and size).
2331 ports= [IP_VS_FTP] IPVS ftp helper module
2333 Up to 8 (IP_VS_APP_MAX_PORTS) ports
2335 Format: <port>,<port>....
2337 print-fatal-signals=
2338 [KNL] debug: print fatal signals
2340 If enabled, warn about various signal handling
2341 related application anomalies: too many signals,
2342 too many POSIX.1 timers, fatal signals causing a
2345 If you hit the warning due to signal overflow,
2346 you might want to try "ulimit -i unlimited".
2350 printk.always_kmsg_dump=
2351 Trigger kmsg_dump for cases other than kernel oops or
2353 Format: <bool> (1/Y/y=enable, 0/N/n=disable)
2356 printk.time= Show timing data prefixed to each printk message line
2357 Format: <bool> (1/Y/y=enable, 0/N/n=disable)
2359 processor.max_cstate= [HW,ACPI]
2360 Limit processor to maximum C-state
2361 max_cstate=9 overrides any DMI blacklist limit.
2363 processor.nocst [HW,ACPI]
2364 Ignore the _CST method to determine C-states,
2365 instead using the legacy FADT method
2367 profile= [KNL] Enable kernel profiling via /proc/profile
2368 Format: [schedule,]<number>
2369 Param: "schedule" - profile schedule points.
2370 Param: <number> - step/bucket size as a power of 2 for
2371 statistical time based profiling.
2372 Param: "sleep" - profile D-state sleeping (millisecs).
2373 Requires CONFIG_SCHEDSTATS
2374 Param: "kvm" - profile VM exits.
2376 prompt_ramdisk= [RAM] List of RAM disks to prompt for floppy disk
2378 See Documentation/blockdev/ramdisk.txt.
2380 psmouse.proto= [HW,MOUSE] Highest PS2 mouse protocol extension to
2381 probe for; one of (bare|imps|exps|lifebook|any).
2382 psmouse.rate= [HW,MOUSE] Set desired mouse report rate, in reports
2384 psmouse.resetafter= [HW,MOUSE]
2385 Try to reset the device after so many bad packets
2388 [HW,MOUSE] Set desired mouse resolution, in dpi.
2389 psmouse.smartscroll=
2390 [HW,MOUSE] Controls Logitech smartscroll autorepeat.
2391 0 = disabled, 1 = enabled (default).
2393 pstore.backend= Specify the name of the pstore backend to use
2396 See Documentation/blockdev/paride.txt.
2399 [KNL] Number of legacy pty's. Overwrites compiled-in
2402 quiet [KNL] Disable most log messages
2407 See Documentation/md.txt.
2409 ramdisk_blocksize= [RAM]
2410 See Documentation/blockdev/ramdisk.txt.
2412 ramdisk_size= [RAM] Sizes of RAM disks in kilobytes
2413 See Documentation/blockdev/ramdisk.txt.
2415 rcutree.blimit= [KNL,BOOT]
2416 Set maximum number of finished RCU callbacks to process
2419 rcutree.fanout_leaf= [KNL,BOOT]
2420 Increase the number of CPUs assigned to each
2421 leaf rcu_node structure. Useful for very large
2424 rcutree.qhimark= [KNL,BOOT]
2425 Set threshold of queued
2426 RCU callbacks over which batch limiting is disabled.
2428 rcutree.qlowmark= [KNL,BOOT]
2429 Set threshold of queued RCU callbacks below which
2430 batch limiting is re-enabled.
2432 rcutree.rcu_cpu_stall_suppress= [KNL,BOOT]
2433 Suppress RCU CPU stall warning messages.
2435 rcutree.rcu_cpu_stall_timeout= [KNL,BOOT]
2436 Set timeout for RCU CPU stall warning messages.
2438 rcutree.jiffies_till_first_fqs= [KNL,BOOT]
2439 Set delay from grace-period initialization to
2440 first attempt to force quiescent states.
2441 Units are jiffies, minimum value is zero,
2442 and maximum value is HZ.
2444 rcutree.jiffies_till_next_fqs= [KNL,BOOT]
2445 Set delay between subsequent attempts to force
2446 quiescent states. Units are jiffies, minimum
2447 value is one, and maximum value is HZ.
2449 rcutorture.fqs_duration= [KNL,BOOT]
2450 Set duration of force_quiescent_state bursts.
2452 rcutorture.fqs_holdoff= [KNL,BOOT]
2453 Set holdoff time within force_quiescent_state bursts.
2455 rcutorture.fqs_stutter= [KNL,BOOT]
2456 Set wait time between force_quiescent_state bursts.
2458 rcutorture.irqreader= [KNL,BOOT]
2459 Test RCU readers from irq handlers.
2461 rcutorture.n_barrier_cbs= [KNL,BOOT]
2462 Set callbacks/threads for rcu_barrier() testing.
2464 rcutorture.nfakewriters= [KNL,BOOT]
2465 Set number of concurrent RCU writers. These just
2466 stress RCU, they don't participate in the actual
2467 test, hence the "fake".
2469 rcutorture.nreaders= [KNL,BOOT]
2470 Set number of RCU readers.
2472 rcutorture.onoff_holdoff= [KNL,BOOT]
2473 Set time (s) after boot for CPU-hotplug testing.
2475 rcutorture.onoff_interval= [KNL,BOOT]
2476 Set time (s) between CPU-hotplug operations, or
2477 zero to disable CPU-hotplug testing.
2479 rcutorture.shuffle_interval= [KNL,BOOT]
2480 Set task-shuffle interval (s). Shuffling tasks
2481 allows some CPUs to go into dyntick-idle mode
2482 during the rcutorture test.
2484 rcutorture.shutdown_secs= [KNL,BOOT]
2485 Set time (s) after boot system shutdown. This
2486 is useful for hands-off automated testing.
2488 rcutorture.stall_cpu= [KNL,BOOT]
2489 Duration of CPU stall (s) to test RCU CPU stall
2490 warnings, zero to disable.
2492 rcutorture.stall_cpu_holdoff= [KNL,BOOT]
2493 Time to wait (s) after boot before inducing stall.
2495 rcutorture.stat_interval= [KNL,BOOT]
2496 Time (s) between statistics printk()s.
2498 rcutorture.stutter= [KNL,BOOT]
2499 Time (s) to stutter testing, for example, specifying
2500 five seconds causes the test to run for five seconds,
2501 wait for five seconds, and so on. This tests RCU's
2502 ability to transition abruptly to and from idle.
2504 rcutorture.test_boost= [KNL,BOOT]
2505 Test RCU priority boosting? 0=no, 1=maybe, 2=yes.
2506 "Maybe" means test if the RCU implementation
2507 under test support RCU priority boosting.
2509 rcutorture.test_boost_duration= [KNL,BOOT]
2510 Duration (s) of each individual boost test.
2512 rcutorture.test_boost_interval= [KNL,BOOT]
2513 Interval (s) between each boost test.
2515 rcutorture.test_no_idle_hz= [KNL,BOOT]
2516 Test RCU's dyntick-idle handling. See also the
2517 rcutorture.shuffle_interval parameter.
2519 rcutorture.torture_type= [KNL,BOOT]
2520 Specify the RCU implementation to test.
2522 rcutorture.verbose= [KNL,BOOT]
2523 Enable additional printk() statements.
2527 Run specified binary instead of /init from the ramdisk,
2528 used for early userspace startup. See initrd.
2530 reboot= [BUGS=X86-32,BUGS=ARM,BUGS=IA-64] Rebooting mode
2531 Format: <reboot_mode>[,<reboot_mode2>[,...]]
2532 See arch/*/kernel/reboot.c or arch/*/kernel/process.c
2535 [KNL, SMP] Set scheduler's default relax_domain_level.
2536 See Documentation/cgroups/cpusets.txt.
2538 reserve= [KNL,BUGS] Force the kernel to ignore some iomem area
2540 reservetop= [X86-32]
2542 Reserves a hole at the top of the kernel virtual
2547 Set the amount of memory to reserve for BIOS at
2548 the bottom of the address space.
2550 reset_devices [KNL] Force drivers to reset the underlying device
2551 during initialization.
2554 Specify the partition device for software suspend
2556 {/dev/<dev> | PARTUUID=<uuid> | <int>:<int> | <hex>}
2558 resume_offset= [SWSUSP]
2559 Specify the offset from the beginning of the partition
2560 given by "resume=" at which the swap header is located,
2561 in <PAGE_SIZE> units (needed only for swap files).
2562 See Documentation/power/swsusp-and-swap-files.txt
2564 resumedelay= [HIBERNATION] Delay (in seconds) to pause before attempting to
2565 read the resume files
2567 resumewait [HIBERNATION] Wait (indefinitely) for resume device to show up.
2568 Useful for devices that are detected asynchronously
2569 (e.g. USB and MMC devices).
2571 hibernate= [HIBERNATION]
2572 noresume Don't check if there's a hibernation image
2573 present during boot.
2574 nocompress Don't compress/decompress hibernation images.
2576 retain_initrd [RAM] Keep initrd memory after extraction
2578 rhash_entries= [KNL,NET]
2579 Set number of hash buckets for route cache
2581 riscom8= [HW,SERIAL]
2582 Format: <io_board1>[,<io_board2>[,...<io_boardN>]]
2584 ro [KNL] Mount root device read-only on boot
2586 root= [KNL] Root filesystem
2587 See name_to_dev_t comment in init/do_mounts.c.
2589 rootdelay= [KNL] Delay (in seconds) to pause before attempting to
2590 mount the root filesystem
2592 rootflags= [KNL] Set root filesystem mount option string
2594 rootfstype= [KNL] Set root filesystem type
2596 rootwait [KNL] Wait (indefinitely) for root device to show up.
2597 Useful for devices that are detected asynchronously
2598 (e.g. USB and MMC devices).
2600 rw [KNL] Mount root device read-write on boot
2602 S [KNL] Run init in single mode
2605 See drivers/net/irda/sa1100_ir.c.
2607 sbni= [NET] Granch SBNI12 leased line adapter
2609 sched_debug [KNL] Enables verbose scheduler debug messages.
2611 skew_tick= [KNL] Offset the periodic timer tick per cpu to mitigate
2612 xtime_lock contention on larger systems, and/or RCU lock
2613 contention on all systems with CONFIG_MAXSMP set.
2614 Format: { "0" | "1" }
2615 0 -- disable. (may be 1 via CONFIG_CMDLINE="skew_tick=1"
2617 Note: increases power consumption, thus should only be
2618 enabled if running jitter sensitive (HPC/RT) workloads.
2620 security= [SECURITY] Choose a security module to enable at boot.
2621 If this boot parameter is not specified, only the first
2622 security module asking for security registration will be
2623 loaded. An invalid security module name will be treated
2624 as if no module has been chosen.
2626 selinux= [SELINUX] Disable or enable SELinux at boot time.
2627 Format: { "0" | "1" }
2628 See security/selinux/Kconfig help text.
2631 Default value is set via kernel config option.
2632 If enabled at boot time, /selinux/disable can be used
2633 later to disable prior to initial policy load.
2635 apparmor= [APPARMOR] Disable or enable AppArmor at boot time
2636 Format: { "0" | "1" }
2637 See security/apparmor/Kconfig help text
2640 Default value is set via kernel config option.
2642 serialnumber [BUGS=X86-32]
2645 Maximal number of shapers.
2647 show_msr= [x86] show boot-time MSR settings
2648 Format: { <integer> }
2649 Show boot-time (BIOS-initialized) MSR settings.
2650 The parameter means the number of CPUs to show,
2651 for example 1 means boot CPU only.
2658 slab_max_order= [MM, SLAB]
2659 Determines the maximum allowed order for slabs.
2660 A high setting may cause OOMs due to memory
2661 fragmentation. Defaults to 1 for systems with
2662 more than 32MB of RAM, 0 otherwise.
2664 slub_debug[=options[,slabs]] [MM, SLUB]
2665 Enabling slub_debug allows one to determine the
2666 culprit if slab objects become corrupted. Enabling
2667 slub_debug can create guard zones around objects and
2668 may poison objects when not in use. Also tracks the
2669 last alloc / free. For more information see
2670 Documentation/vm/slub.txt.
2672 slub_max_order= [MM, SLUB]
2673 Determines the maximum allowed order for slabs.
2674 A high setting may cause OOMs due to memory
2675 fragmentation. For more information see
2676 Documentation/vm/slub.txt.
2678 slub_min_objects= [MM, SLUB]
2679 The minimum number of objects per slab. SLUB will
2680 increase the slab order up to slub_max_order to
2681 generate a sufficiently large slab able to contain
2682 the number of objects indicated. The higher the number
2683 of objects the smaller the overhead of tracking slabs
2684 and the less frequently locks need to be acquired.
2685 For more information see Documentation/vm/slub.txt.
2687 slub_min_order= [MM, SLUB]
2688 Determines the minimum page order for slabs. Must be
2689 lower than slub_max_order.
2690 For more information see Documentation/vm/slub.txt.
2692 slub_nomerge [MM, SLUB]
2693 Disable merging of slabs with similar size. May be
2694 necessary if there is some reason to distinguish
2695 allocs to different slabs. Debug options disable
2696 merging on their own.
2697 For more information see Documentation/vm/slub.txt.
2700 Format: <io1>[,<io2>[,...,<io8>]]
2702 smsc-ircc2.nopnp [HW] Don't use PNP to discover SMC devices
2703 smsc-ircc2.ircc_cfg= [HW] Device configuration I/O port
2704 smsc-ircc2.ircc_sir= [HW] SIR base I/O port
2705 smsc-ircc2.ircc_fir= [HW] FIR base I/O port
2706 smsc-ircc2.ircc_irq= [HW] IRQ line
2707 smsc-ircc2.ircc_dma= [HW] DMA channel
2708 smsc-ircc2.ircc_transceiver= [HW] Transceiver type:
2709 0: Toshiba Satellite 1800 (GP data pin select)
2710 1: Fast pin select (default)
2714 [KNL] Should the soft-lockup detector generate panics.
2717 sonypi.*= [HW] Sony Programmable I/O Control Device driver
2718 See Documentation/laptops/sonypi.txt
2720 specialix= [HW,SERIAL] Specialix multi-serial port adapter
2721 See Documentation/serial/specialix.txt.
2723 spia_io_base= [HW,MTD]
2729 Enabled the stack tracer on boot up.
2731 stacktrace_filter=[function-list]
2732 [FTRACE] Limit the functions that the stack tracer
2733 will trace at boot up. function-list is a comma separated
2734 list of functions. This list can be changed at run
2735 time by the stack_trace_filter file in the debugfs
2736 tracing directory. Note, this enables stack tracing
2737 and the stacktrace above is not needed.
2741 Set the STI (builtin display/keyboard on the HP-PARISC
2742 machines) console (graphic card) which should be used
2743 as the initial boot-console.
2744 See also comment in drivers/video/console/sticore.c.
2747 See comment in drivers/video/console/sticore.c.
2750 Format: bpp:<bpp1>[:<bpp2>[:<bpp3>...]]
2752 sunrpc.min_resvport=
2753 sunrpc.max_resvport=
2755 SunRPC servers often require that client requests
2756 originate from a privileged port (i.e. a port in the
2757 range 0 < portnr < 1024).
2758 An administrator who wishes to reserve some of these
2759 ports for other uses may adjust the range that the
2760 kernel's sunrpc client considers to be privileged
2761 using these two parameters to set the minimum and
2762 maximum port values.
2766 Control how the NFS server code allocates CPUs to
2767 service thread pools. Depending on how many NICs
2768 you have and where their interrupts are bound, this
2769 option will affect which CPUs will do NFS serving.
2770 Note: this parameter cannot be changed while the
2771 NFS server is running.
2773 auto the server chooses an appropriate mode
2774 automatically using heuristics
2775 global a single global pool contains all CPUs
2776 percpu one pool for each CPU
2777 pernode one pool for each NUMA node (equivalent
2778 to global on non-NUMA machines)
2780 sunrpc.tcp_slot_table_entries=
2781 sunrpc.udp_slot_table_entries=
2783 Sets the upper limit on the number of simultaneous
2784 RPC calls that can be sent from the client to a
2785 server. Increasing these values may allow you to
2786 improve throughput, but will also increase the
2787 amount of memory reserved for use by the client.
2790 [KNL] Enable accounting of swap in memory resource
2791 controller if no parameter or 1 is given or disable
2792 it if 0 is given (See Documentation/cgroups/memory.txt)
2794 swiotlb= [IA-64] Number of I/O TLB slabs
2798 sysfs.deprecated=0|1 [KNL]
2799 Enable/disable old style sysfs layout for old udev
2800 on older distributions. When this option is enabled
2801 very new udev will not work anymore. When this option
2802 is disabled (or CONFIG_SYSFS_DEPRECATED not compiled)
2803 in older udev will not work anymore.
2804 Default depends on CONFIG_SYSFS_DEPRECATED_V2 set in
2805 the kernel configuration.
2807 sysrq_always_enabled
2809 Ignore sysrq setting - this boot parameter will
2810 neutralize any effect of /proc/sys/kernel/sysrq.
2811 Useful for debugging.
2815 test_suspend= [SUSPEND]
2816 Specify "mem" (for Suspend-to-RAM) or "standby" (for
2817 standby suspend) as the system sleep state to briefly
2818 enter during system startup. The system is woken from
2819 this state using a wakeup-capable RTC alarm.
2821 thash_entries= [KNL,NET]
2822 Set number of hash buckets for TCP connection
2824 thermal.act= [HW,ACPI]
2825 -1: disable all active trip points in all thermal zones
2826 <degrees C>: override all lowest active trip points
2828 thermal.crt= [HW,ACPI]
2829 -1: disable all critical trip points in all thermal zones
2830 <degrees C>: override all critical trip points
2832 thermal.nocrt= [HW,ACPI]
2833 Set to disable actions on ACPI thermal zone
2834 critical and hot trip points.
2836 thermal.off= [HW,ACPI]
2837 1: disable ACPI thermal control
2839 thermal.psv= [HW,ACPI]
2840 -1: disable all passive trip points
2841 <degrees C>: override all passive trip points to this
2844 thermal.tzp= [HW,ACPI]
2845 Specify global default ACPI thermal zone polling rate
2846 <deci-seconds>: poll all this frequency
2847 0: no polling (default)
2850 Force threading of all interrupt handlers except those
2851 marked explicitly IRQF_NO_THREAD.
2855 Specify if the kernel should make use of the cpu
2856 topology information if the hardware supports this.
2857 The scheduler will make use of this information and
2858 e.g. base its process migration decisions on it.
2863 tpm_suspend_pcr=[HW,TPM]
2864 Format: integer pcr id
2865 Specify that at suspend time, the tpm driver
2866 should extend the specified pcr with zeros,
2867 as a workaround for some chips which fail to
2868 flush the last written pcr on TPM_SaveState.
2869 This will guarantee that all the other pcrs
2872 trace_buf_size=nn[KMG]
2873 [FTRACE] will set tracing buffer size.
2875 trace_event=[event-list]
2876 [FTRACE] Set and start specified trace events in order
2877 to facilitate early boot debugging.
2878 See also Documentation/trace/events.txt
2880 transparent_hugepage=
2882 Format: [always|madvise|never]
2883 Can be used to control the default behavior of the system
2884 with respect to transparent hugepages.
2885 See Documentation/vm/transhuge.txt for more details.
2887 tsc= Disable clocksource stability checks for TSC.
2889 [x86] reliable: mark tsc clocksource as reliable, this
2890 disables clocksource verification at runtime, as well
2891 as the stability checks done at bootup. Used to enable
2892 high-resolution timer mode on older hardware, and in
2893 virtualized environment.
2894 [x86] noirqtime: Do not use TSC to do irq accounting.
2895 Used to run time disable IRQ_TIME_ACCOUNTING on any
2896 platforms where RDTSC is slow and this accounting
2899 turbografx.map[2|3]= [HW,JOY]
2900 TurboGraFX parallel port interface
2902 <port#>,<js1>,<js2>,<js3>,<js4>,<js5>,<js6>,<js7>
2903 See also Documentation/input/joystick-parport.txt
2905 udbg-immortal [PPC] When debugging early kernel crashes that
2906 happen after console_init() and before a proper
2907 console driver takes over, this boot options might
2908 help "seeing" what's going on.
2910 uhash_entries= [KNL,NET]
2911 Set number of hash buckets for UDP/UDP-Lite connections
2914 [USB] Ignore overcurrent events (default N).
2915 Some badly-designed motherboards generate lots of
2916 bogus events, for ports that aren't wired to
2917 anything. Set this parameter to avoid log spamming.
2918 Note that genuine overcurrent events won't be
2922 [X86] Cause panic on unknown NMI.
2924 usbcore.authorized_default=
2925 [USB] Default USB device authorization:
2926 (default -1 = authorized except for wireless USB,
2927 0 = not authorized, 1 = authorized)
2929 usbcore.autosuspend=
2930 [USB] The autosuspend time delay (in seconds) used
2931 for newly-detected USB devices (default 2). This
2932 is the time required before an idle device will be
2933 autosuspended. Devices for which the delay is set
2934 to a negative value won't be autosuspended at all.
2936 usbcore.usbfs_snoop=
2937 [USB] Set to log all usbfs traffic (default 0 = off).
2939 usbcore.blinkenlights=
2940 [USB] Set to cycle leds on hubs (default 0 = off).
2942 usbcore.old_scheme_first=
2943 [USB] Start with the old device initialization
2944 scheme (default 0 = off).
2946 usbcore.usbfs_memory_mb=
2947 [USB] Memory limit (in MB) for buffers allocated by
2948 usbfs (default = 16, 0 = max = 2047).
2950 usbcore.use_both_schemes=
2951 [USB] Try the other device initialization scheme
2952 if the first one fails (default 1 = enabled).
2954 usbcore.initial_descriptor_timeout=
2955 [USB] Specifies timeout for the initial 64-byte
2956 USB_REQ_GET_DESCRIPTOR request in milliseconds
2957 (default 5000 = 5.0 seconds).
2960 [USBHID] The interval which mice are to be polled at.
2962 usb-storage.delay_use=
2963 [UMS] The delay in seconds before a new device is
2964 scanned for Logical Units (default 5).
2967 [UMS] A list of quirks entries to supplement or
2968 override the built-in unusual_devs list. List
2969 entries are separated by commas. Each entry has
2970 the form VID:PID:Flags where VID and PID are Vendor
2971 and Product ID values (4-digit hex numbers) and
2972 Flags is a set of characters, each corresponding
2973 to a common usb-storage quirk flag as follows:
2974 a = SANE_SENSE (collect more than 18 bytes
2976 b = BAD_SENSE (don't collect more than 18
2977 bytes of sense data);
2978 c = FIX_CAPACITY (decrease the reported
2979 device capacity by one sector);
2980 d = NO_READ_DISC_INFO (don't use
2981 READ_DISC_INFO command);
2982 e = NO_READ_CAPACITY_16 (don't use
2983 READ_CAPACITY_16 command);
2984 h = CAPACITY_HEURISTICS (decrease the
2985 reported device capacity by one
2986 sector if the number is odd);
2987 i = IGNORE_DEVICE (don't bind to this
2989 l = NOT_LOCKABLE (don't try to lock and
2990 unlock ejectable media);
2991 m = MAX_SECTORS_64 (don't transfer more
2992 than 64 sectors = 32 KB at a time);
2993 n = INITIAL_READ10 (force a retry of the
2994 initial READ(10) command);
2995 o = CAPACITY_OK (accept the capacity
2996 reported by the device);
2997 p = WRITE_CACHE (the device cache is ON
2999 r = IGNORE_RESIDUE (the device reports
3000 bogus residue values);
3001 s = SINGLE_LUN (the device has only one
3003 w = NO_WP_DETECT (don't test whether the
3004 medium is write-protected).
3005 Example: quirks=0419:aaf5:rl,0421:0433:rc
3007 user_debug= [KNL,ARM]
3009 See arch/arm/Kconfig.debug help text.
3010 1 - undefined instruction events
3012 4 - invalid data aborts
3015 Example: user_debug=31
3018 [X86] Flags controlling user PTE allocations.
3020 nohigh = do not allocate PTE pages in
3021 HIGHMEM regardless of setting
3025 vdso=2: enable compat VDSO (default with COMPAT_VDSO)
3026 vdso=1: enable VDSO (default)
3027 vdso=0: disable VDSO mapping
3030 vdso32=2: enable compat VDSO (default with COMPAT_VDSO)
3031 vdso32=1: enable 32-bit VDSO (default)
3032 vdso32=0: disable 32-bit VDSO mapping
3035 vector=percpu: enable percpu vector domain
3037 video= [FB] Frame buffer configuration
3038 See Documentation/fb/modedb.txt.
3041 [VMMIO] Memory mapped virtio (platform) device.
3043 <size>@<baseaddr>:<irq>[:<id>]
3045 <size> := size (can use standard suffixes
3047 <baseaddr> := physical base address
3048 <irq> := interrupt number (as passed to
3050 <id> := (optional) platform device id
3052 virtio_mmio.device=1K@0x100b0000:48:7
3054 Can be used multiple times for multiple devices.
3056 vga= [BOOT,X86-32] Select a particular video mode
3057 See Documentation/x86/boot.txt and
3058 Documentation/svga.txt.
3059 Use vga=ask for menu.
3060 This is actually a boot loader parameter; the value is
3061 passed to the kernel using a special protocol.
3063 vmalloc=nn[KMG] [KNL,BOOT] Forces the vmalloc area to have an exact
3064 size of <nn>. This can be used to increase the
3065 minimum size (128MB on x86). It can also be used to
3066 decrease the size and leave more room for directly
3069 vmhalt= [KNL,S390] Perform z/VM CP command after system halt.
3072 vmpanic= [KNL,S390] Perform z/VM CP command after kernel panic.
3075 vmpoff= [KNL,S390] Perform z/VM CP command after power off.
3079 Controls the behavior of vsyscalls (i.e. calls to
3080 fixed addresses of 0xffffffffff600x00 from legacy
3081 code). Most statically-linked binaries and older
3082 versions of glibc use these calls. Because these
3083 functions are at fixed addresses, they make nice
3084 targets for exploits that can control RIP.
3086 emulate [default] Vsyscalls turn into traps and are
3087 emulated reasonably safely.
3089 native Vsyscalls are native syscall instructions.
3090 This is a little bit faster than trapping
3091 and makes a few dynamic recompilers work
3092 better than they would in emulation mode.
3093 It also makes exploits much easier to write.
3095 none Vsyscalls don't work at all. This makes
3096 them quite hard to use for exploits but
3097 might break your system.
3099 vt.cur_default= [VT] Default cursor shape.
3100 Format: 0xCCBBAA, where AA, BB, and CC are the same as
3101 the parameters of the <Esc>[?A;B;Cc escape sequence;
3102 see VGA-softcursor.txt. Default: 2 = underline.
3104 vt.default_blu= [VT]
3105 Format: <blue0>,<blue1>,<blue2>,...,<blue15>
3106 Change the default blue palette of the console.
3107 This is a 16-member array composed of values
3110 vt.default_grn= [VT]
3111 Format: <green0>,<green1>,<green2>,...,<green15>
3112 Change the default green palette of the console.
3113 This is a 16-member array composed of values
3116 vt.default_red= [VT]
3117 Format: <red0>,<red1>,<red2>,...,<red15>
3118 Change the default red palette of the console.
3119 This is a 16-member array composed of values
3125 Set system-wide default UTF-8 mode for all tty's.
3126 Default is 1, i.e. UTF-8 mode is enabled for all
3127 newly opened terminals.
3129 vt.global_cursor_default=
3132 Set system-wide default for whether a cursor
3133 is shown on new VTs. Default is -1,
3134 i.e. cursors will be created by default unless
3135 overridden by individual drivers. 0 will hide
3136 cursors, 1 will display them.
3138 watchdog timers [HW,WDT] For information on watchdog timers,
3139 see Documentation/watchdog/watchdog-parameters.txt
3140 or other driver-specific files in the
3141 Documentation/watchdog/ directory.
3143 x2apic_phys [X86-64,APIC] Use x2apic physical mode instead of
3144 default x2apic cluster mode on platforms
3147 x86_mrst_timer= [X86-32,APBT]
3148 Choose timer option for x86 Moorestown MID platform.
3149 Two valid options are apbt timer only and lapic timer
3150 plus one apbt timer for broadcast timer.
3151 x86_mrst_timer=apbt_only | lapic_and_apbt
3153 xd= [HW,XT] Original XT pre-IDE (RLL encoded) disks.
3154 xd_geo= See header of drivers/block/xd.c.
3156 xen_emul_unplug= [HW,X86,XEN]
3157 Unplug Xen emulated devices
3158 Format: [unplug0,][unplug1]
3159 ide-disks -- unplug primary master IDE devices
3160 aux-ide-disks -- unplug non-primary-master IDE devices
3161 nics -- unplug network devices
3162 all -- unplug all emulated devices (NICs and IDE disks)
3163 unnecessary -- unplugging emulated devices is
3164 unnecessary even if the host did not respond to
3166 never -- do not unplug even if version check succeeds
3168 xirc2ps_cs= [NET,PCMCIA]
3170 <irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
3172 ______________________________________________________________________
3176 Add more DRM drivers.
projects / deliverable / linux.git / blob