[deliverable/linux.git] / arch / arc / mm / cache_arc700.c

/*
 * ARC700 VIPT Cache Management
 *
 * Copyright (C) 2004, 2007-2010, 2011-2012 Synopsys, Inc. (www.synopsys.com)
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License version 2 as
 * published by the Free Software Foundation.
 *
 *  vineetg: May 2011: for Non-aliasing VIPT D-cache following can be NOPs
 *   -flush_cache_dup_mm (fork)
 *   -likewise for flush_cache_mm (exit/execve)
 *   -likewise for flush_cache_range,flush_cache_page (munmap, exit, COW-break)
 *
 * vineetg: Apr 2011
 *  -Now that MMU can support larger pg sz (16K), the determiniation of
 *   aliasing shd not be based on assumption of 8k pg
 *
 * vineetg: Mar 2011
 *  -optimised version of flush_icache_range( ) for making I/D coherent
 *   when vaddr is available (agnostic of num of aliases)
 *
 * vineetg: Mar 2011
 *  -Added documentation about I-cache aliasing on ARC700 and the way it
 *   was handled up until MMU V2.
 *  -Spotted a three year old bug when killing the 4 aliases, which needs
 *   bottom 2 bits, so we need to do paddr | {0x00, 0x01, 0x02, 0x03}
 *                        instead of paddr | {0x00, 0x01, 0x10, 0x11}
 *   (Rajesh you owe me one now)
 *
 * vineetg: Dec 2010
 *  -Off-by-one error when computing num_of_lines to flush
 *   This broke signal handling with bionic which uses synthetic sigret stub
 *
 * vineetg: Mar 2010
 *  -GCC can't generate ZOL for core cache flush loops.
 *   Conv them into iterations based as opposed to while (start < end) types
 *
 * Vineetg: July 2009
 *  -In I-cache flush routine we used to chk for aliasing for every line INV.
 *   Instead now we setup routines per cache geometry and invoke them
 *   via function pointers.
 *
 * Vineetg: Jan 2009
 *  -Cache Line flush routines used to flush an extra line beyond end addr
 *   because check was while (end >= start) instead of (end > start)
 *     =Some call sites had to work around by doing -1, -4 etc to end param
 *     =Some callers didnt care. This was spec bad in case of INV routines
 *      which would discard valid data (cause of the horrible ext2 bug
 *      in ARC IDE driver)
 *
 * vineetg: June 11th 2008: Fixed flush_icache_range( )
 *  -Since ARC700 caches are not coherent (I$ doesnt snoop D$) both need
 *   to be flushed, which it was not doing.
 *  -load_module( ) passes vmalloc addr (Kernel Virtual Addr) to the API,
 *   however ARC cache maintenance OPs require PHY addr. Thus need to do
 *   vmalloc_to_phy.
 *  -Also added optimisation there, that for range > PAGE SIZE we flush the
 *   entire cache in one shot rather than line by line. For e.g. a module
 *   with Code sz 600k, old code flushed 600k worth of cache (line-by-line),
 *   while cache is only 16 or 32k.
 */

#include <linux/module.h>
#include <linux/mm.h>
#include <linux/sched.h>
#include <linux/cache.h>
#include <linux/mmu_context.h>
#include <linux/syscalls.h>
#include <linux/uaccess.h>
#include <linux/pagemap.h>
#include <asm/cacheflush.h>
#include <asm/cachectl.h>
#include <asm/setup.h>

char *arc_cache_mumbojumbo(int c, char *buf, int len)
{
        int n = 0;

#define PR_CACHE(p, cfg, str)                                           \
        if (!(p)->ver)                                                  \
                n += scnprintf(buf + n, len - n, str"\t\t: N/A\n");     \
        else                                                            \
                n += scnprintf(buf + n, len - n,                        \
                        str"\t\t: %uK, %dway/set, %uB Line, %s%s%s\n",  \
                        (p)->sz_k, (p)->assoc, (p)->line_len,           \
                        (p)->vipt ? "VIPT" : "PIPT",                    \
                        (p)->alias ? " aliasing" : "",                  \
                        IS_ENABLED(cfg) ? "" : " (not used)");

        PR_CACHE(&cpuinfo_arc700[c].icache, CONFIG_ARC_HAS_ICACHE, "I-Cache");
        PR_CACHE(&cpuinfo_arc700[c].dcache, CONFIG_ARC_HAS_DCACHE, "D-Cache");

        return buf;
}

/*
 * Read the Cache Build Confuration Registers, Decode them and save into
 * the cpuinfo structure for later use.
 * No Validation done here, simply read/convert the BCRs
 */
void read_decode_cache_bcr(void)
{
        struct cpuinfo_arc_cache *p_ic, *p_dc;
        unsigned int cpu = smp_processor_id();
        struct bcr_cache {
#ifdef CONFIG_CPU_BIG_ENDIAN
                unsigned int pad:12, line_len:4, sz:4, config:4, ver:8;
#else
                unsigned int ver:8, config:4, sz:4, line_len:4, pad:12;
#endif
        } ibcr, dbcr;

        p_ic = &cpuinfo_arc700[cpu].icache;
        READ_BCR(ARC_REG_IC_BCR, ibcr);

        if (!ibcr.ver)
                goto dc_chk;

        BUG_ON(ibcr.config != 3);
        p_ic->assoc = 2;                /* Fixed to 2w set assoc */
        p_ic->line_len = 8 << ibcr.line_len;
        p_ic->sz_k = 1 << (ibcr.sz - 1);
        p_ic->ver = ibcr.ver;
        p_ic->vipt = 1;
        p_ic->alias = p_ic->sz_k/p_ic->assoc/TO_KB(PAGE_SIZE) > 1;

dc_chk:
        p_dc = &cpuinfo_arc700[cpu].dcache;
        READ_BCR(ARC_REG_DC_BCR, dbcr);

        if (!dbcr.ver)
                return;

        BUG_ON(dbcr.config != 2);
        p_dc->assoc = 4;                /* Fixed to 4w set assoc */
        p_dc->line_len = 16 << dbcr.line_len;
        p_dc->sz_k = 1 << (dbcr.sz - 1);
        p_dc->ver = dbcr.ver;
        p_dc->vipt = 1;
        p_dc->alias = p_dc->sz_k/p_dc->assoc/TO_KB(PAGE_SIZE) > 1;
}

/*
 * 1. Validate the Cache Geomtery (compile time config matches hardware)
 * 2. If I-cache suffers from aliasing, setup work arounds (difft flush rtn)
 *    (aliasing D-cache configurations are not supported YET)
 * 3. Enable the Caches, setup default flush mode for D-Cache
 * 3. Calculate the SHMLBA used by user space
 */
void arc_cache_init(void)
{
        unsigned int __maybe_unused cpu = smp_processor_id();
        char str[256];

        printk(arc_cache_mumbojumbo(0, str, sizeof(str)));

        if (IS_ENABLED(CONFIG_ARC_HAS_ICACHE)) {
                struct cpuinfo_arc_cache *ic = &cpuinfo_arc700[cpu].icache;

                if (!ic->ver)
                        panic("cache support enabled but non-existent cache\n");

                if (ic->line_len != L1_CACHE_BYTES)
                        panic("ICache line [%d] != kernel Config [%d]",
                              ic->line_len, L1_CACHE_BYTES);

                if (ic->ver != CONFIG_ARC_MMU_VER)
                        panic("Cache ver [%d] doesn't match MMU ver [%d]\n",
                              ic->ver, CONFIG_ARC_MMU_VER);
        }

        if (IS_ENABLED(CONFIG_ARC_HAS_DCACHE)) {
                struct cpuinfo_arc_cache *dc = &cpuinfo_arc700[cpu].dcache;
                int handled;

                if (!dc->ver)
                        panic("cache support enabled but non-existent cache\n");

                if (dc->line_len != L1_CACHE_BYTES)
                        panic("DCache line [%d] != kernel Config [%d]",
                              dc->line_len, L1_CACHE_BYTES);

                /* check for D-Cache aliasing */
                handled = IS_ENABLED(CONFIG_ARC_CACHE_VIPT_ALIASING);

                if (dc->alias && !handled)
                        panic("Enable CONFIG_ARC_CACHE_VIPT_ALIASING\n");
                else if (!dc->alias && handled)
                        panic("Don't need CONFIG_ARC_CACHE_VIPT_ALIASING\n");
        }
}

#define OP_INV          0x1
#define OP_FLUSH        0x2
#define OP_FLUSH_N_INV  0x3
#define OP_INV_IC       0x4

/*
 * Common Helper for Line Operations on {I,D}-Cache
 */
static inline void __cache_line_loop(unsigned long paddr, unsigned long vaddr,
                                     unsigned long sz, const int cacheop)
{
        unsigned int aux_cmd, aux_tag;
        int num_lines;
        const int full_page_op = __builtin_constant_p(sz) && sz == PAGE_SIZE;

        if (cacheop == OP_INV_IC) {
                aux_cmd = ARC_REG_IC_IVIL;
#if (CONFIG_ARC_MMU_VER > 2)
                aux_tag = ARC_REG_IC_PTAG;
#endif
        }
        else {
                /* d$ cmd: INV (discard or wback-n-discard) OR FLUSH (wback) */
                aux_cmd = cacheop & OP_INV ? ARC_REG_DC_IVDL : ARC_REG_DC_FLDL;
#if (CONFIG_ARC_MMU_VER > 2)
                aux_tag = ARC_REG_DC_PTAG;
#endif
        }

        /* Ensure we properly floor/ceil the non-line aligned/sized requests
         * and have @paddr - aligned to cache line and integral @num_lines.
         * This however can be avoided for page sized since:
         *  -@paddr will be cache-line aligned already (being page aligned)
         *  -@sz will be integral multiple of line size (being page sized).
         */
        if (!full_page_op) {
                sz += paddr & ~CACHE_LINE_MASK;
                paddr &= CACHE_LINE_MASK;
                vaddr &= CACHE_LINE_MASK;
        }

        num_lines = DIV_ROUND_UP(sz, L1_CACHE_BYTES);

#if (CONFIG_ARC_MMU_VER <= 2)
        /* MMUv2 and before: paddr contains stuffed vaddrs bits */
        paddr |= (vaddr >> PAGE_SHIFT) & 0x1F;
#else
        /* if V-P const for loop, PTAG can be written once outside loop */
        if (full_page_op)
                write_aux_reg(aux_tag, paddr);
#endif

        while (num_lines-- > 0) {
#if (CONFIG_ARC_MMU_VER > 2)
                /* MMUv3, cache ops require paddr seperately */
                if (!full_page_op) {
                        write_aux_reg(aux_tag, paddr);
                        paddr += L1_CACHE_BYTES;
                }

                write_aux_reg(aux_cmd, vaddr);
                vaddr += L1_CACHE_BYTES;
#else
                write_aux_reg(aux_cmd, paddr);
                paddr += L1_CACHE_BYTES;
#endif
        }
}

#ifdef CONFIG_ARC_HAS_DCACHE

/***************************************************************
 * Machine specific helpers for Entire D-Cache or Per Line ops
 */

static unsigned int __before_dc_op(const int op)
{
        unsigned int reg = reg;

        if (op == OP_FLUSH_N_INV) {
                /* Dcache provides 2 cmd: FLUSH or INV
                 * INV inturn has sub-modes: DISCARD or FLUSH-BEFORE
                 * flush-n-inv is achieved by INV cmd but with IM=1
                 * So toggle INV sub-mode depending on op request and default
                 */
                reg = read_aux_reg(ARC_REG_DC_CTRL);
                write_aux_reg(ARC_REG_DC_CTRL, reg | DC_CTRL_INV_MODE_FLUSH)
                        ;
        }

        return reg;
}

static void __after_dc_op(const int op, unsigned int reg)
{
        if (op & OP_FLUSH)      /* flush / flush-n-inv both wait */
                while (read_aux_reg(ARC_REG_DC_CTRL) & DC_CTRL_FLUSH_STATUS);

        /* Switch back to default Invalidate mode */
        if (op == OP_FLUSH_N_INV)
                write_aux_reg(ARC_REG_DC_CTRL, reg & ~DC_CTRL_INV_MODE_FLUSH);
}

/*
 * Operation on Entire D-Cache
 * @cacheop = {OP_INV, OP_FLUSH, OP_FLUSH_N_INV}
 * Note that constant propagation ensures all the checks are gone
 * in generated code
 */
static inline void __dc_entire_op(const int cacheop)
{
        unsigned int ctrl_reg;
        int aux;

        ctrl_reg = __before_dc_op(cacheop);

        if (cacheop & OP_INV)   /* Inv or flush-n-inv use same cmd reg */
                aux = ARC_REG_DC_IVDC;
        else
                aux = ARC_REG_DC_FLSH;

        write_aux_reg(aux, 0x1);

        __after_dc_op(cacheop, ctrl_reg);
}

/* For kernel mappings cache operation: index is same as paddr */
#define __dc_line_op_k(p, sz, op)       __dc_line_op(p, p, sz, op)

/*
 * D-Cache : Per Line INV (discard or wback+discard) or FLUSH (wback)
 */
static inline void __dc_line_op(unsigned long paddr, unsigned long vaddr,
                                unsigned long sz, const int cacheop)
{
        unsigned long flags;
        unsigned int ctrl_reg;

        local_irq_save(flags);

        ctrl_reg = __before_dc_op(cacheop);

        __cache_line_loop(paddr, vaddr, sz, cacheop);

        __after_dc_op(cacheop, ctrl_reg);

        local_irq_restore(flags);
}

#else

#define __dc_entire_op(cacheop)
#define __dc_line_op(paddr, vaddr, sz, cacheop)
#define __dc_line_op_k(paddr, sz, cacheop)

#endif /* CONFIG_ARC_HAS_DCACHE */


#ifdef CONFIG_ARC_HAS_ICACHE

/*
 *              I-Cache Aliasing in ARC700 VIPT caches
 *
 * ARC VIPT I-cache uses vaddr to index into cache and paddr to match the tag.
 * The orig Cache Management Module "CDU" only required paddr to invalidate a
 * certain line since it sufficed as index in Non-Aliasing VIPT cache-geometry.
 * Infact for distinct V1,V2,P: all of {V1-P},{V2-P},{P-P} would end up fetching
 * the exact same line.
 *
 * However for larger Caches (way-size > page-size) - i.e. in Aliasing config,
 * paddr alone could not be used to correctly index the cache.
 *
 * ------------------
 * MMU v1/v2 (Fixed Page Size 8k)
 * ------------------
 * The solution was to provide CDU with these additonal vaddr bits. These
 * would be bits [x:13], x would depend on cache-geometry, 13 comes from
 * standard page size of 8k.
 * H/w folks chose [17:13] to be a future safe range, and moreso these 5 bits
 * of vaddr could easily be "stuffed" in the paddr as bits [4:0] since the
 * orig 5 bits of paddr were anyways ignored by CDU line ops, as they
 * represent the offset within cache-line. The adv of using this "clumsy"
 * interface for additional info was no new reg was needed in CDU programming
 * model.
 *
 * 17:13 represented the max num of bits passable, actual bits needed were
 * fewer, based on the num-of-aliases possible.
 * -for 2 alias possibility, only bit 13 needed (32K cache)
 * -for 4 alias possibility, bits 14:13 needed (64K cache)
 *
 * ------------------
 * MMU v3
 * ------------------
 * This ver of MMU supports variable page sizes (1k-16k): although Linux will
 * only support 8k (default), 16k and 4k.
 * However from hardware perspective, smaller page sizes aggrevate aliasing
 * meaning more vaddr bits needed to disambiguate the cache-line-op ;
 * the existing scheme of piggybacking won't work for certain configurations.
 * Two new registers IC_PTAG and DC_PTAG inttoduced.
 * "tag" bits are provided in PTAG, index bits in existing IVIL/IVDL/FLDL regs
 */

/***********************************************************
 * Machine specific helper for per line I-Cache invalidate.
 */
static void __ic_line_inv_vaddr_local(unsigned long paddr, unsigned long vaddr,
                                unsigned long sz)
{
        unsigned long flags;

        local_irq_save(flags);
        __cache_line_loop(paddr, vaddr, sz, OP_INV_IC);
        local_irq_restore(flags);
}

static inline void __ic_entire_inv(void)
{
        write_aux_reg(ARC_REG_IC_IVIC, 1);
        read_aux_reg(ARC_REG_IC_CTRL);  /* blocks */
}

struct ic_line_inv_vaddr_ipi {
        unsigned long paddr, vaddr;
        int sz;
};

static void __ic_line_inv_vaddr_helper(void *info)
{
        struct ic_line_inv_vaddr_ipi *ic_inv = (struct ic_line_inv_vaddr_ipi*) info;
        __ic_line_inv_vaddr_local(ic_inv->paddr, ic_inv->vaddr, ic_inv->sz);
}

static void __ic_line_inv_vaddr(unsigned long paddr, unsigned long vaddr,
                                unsigned long sz)
{
        struct ic_line_inv_vaddr_ipi ic_inv = { paddr, vaddr , sz};
        on_each_cpu(__ic_line_inv_vaddr_helper, &ic_inv, 1);
}
#else

#define __ic_entire_inv()
#define __ic_line_inv_vaddr(pstart, vstart, sz)

#endif /* CONFIG_ARC_HAS_ICACHE */


/***********************************************************
 * Exported APIs
 */

/*
 * Handle cache congruency of kernel and userspace mappings of page when kernel
 * writes-to/reads-from
 *
 * The idea is to defer flushing of kernel mapping after a WRITE, possible if:
 *  -dcache is NOT aliasing, hence any U/K-mappings of page are congruent
 *  -U-mapping doesn't exist yet for page (finalised in update_mmu_cache)
 *  -In SMP, if hardware caches are coherent
 *
 * There's a corollary case, where kernel READs from a userspace mapped page.
 * If the U-mapping is not congruent to to K-mapping, former needs flushing.
 */
void flush_dcache_page(struct page *page)
{
        struct address_space *mapping;

        if (!cache_is_vipt_aliasing()) {
                clear_bit(PG_dc_clean, &page->flags);
                return;
        }

        /* don't handle anon pages here */
        mapping = page_mapping(page);
        if (!mapping)
                return;

        /*
         * pagecache page, file not yet mapped to userspace
         * Make a note that K-mapping is dirty
         */
        if (!mapping_mapped(mapping)) {
                clear_bit(PG_dc_clean, &page->flags);
        } else if (page_mapped(page)) {

                /* kernel reading from page with U-mapping */
                void *paddr = page_address(page);
                unsigned long vaddr = page->index << PAGE_CACHE_SHIFT;

                if (addr_not_cache_congruent(paddr, vaddr))
                        __flush_dcache_page(paddr, vaddr);
        }
}
EXPORT_SYMBOL(flush_dcache_page);


void dma_cache_wback_inv(unsigned long start, unsigned long sz)
{
        __dc_line_op_k(start, sz, OP_FLUSH_N_INV);
}
EXPORT_SYMBOL(dma_cache_wback_inv);

void dma_cache_inv(unsigned long start, unsigned long sz)
{
        __dc_line_op_k(start, sz, OP_INV);
}
EXPORT_SYMBOL(dma_cache_inv);

void dma_cache_wback(unsigned long start, unsigned long sz)
{
        __dc_line_op_k(start, sz, OP_FLUSH);
}
EXPORT_SYMBOL(dma_cache_wback);

/*
 * This is API for making I/D Caches consistent when modifying
 * kernel code (loadable modules, kprobes, kgdb...)
 * This is called on insmod, with kernel virtual address for CODE of
 * the module. ARC cache maintenance ops require PHY address thus we
 * need to convert vmalloc addr to PHY addr
 */
void flush_icache_range(unsigned long kstart, unsigned long kend)
{
        unsigned int tot_sz, off, sz;
        unsigned long phy, pfn;

        /* printk("Kernel Cache Cohenercy: %lx to %lx\n",kstart, kend); */

        /* This is not the right API for user virtual address */
        if (kstart < TASK_SIZE) {
                BUG_ON("Flush icache range for user virtual addr space");
                return;
        }

        /* Shortcut for bigger flush ranges.
         * Here we don't care if this was kernel virtual or phy addr
         */
        tot_sz = kend - kstart;
        if (tot_sz > PAGE_SIZE) {
                flush_cache_all();
                return;
        }

        /* Case: Kernel Phy addr (0x8000_0000 onwards) */
        if (likely(kstart > PAGE_OFFSET)) {
                /*
                 * The 2nd arg despite being paddr will be used to index icache
                 * This is OK since no alternate virtual mappings will exist
                 * given the callers for this case: kprobe/kgdb in built-in
                 * kernel code only.
                 */
                __sync_icache_dcache(kstart, kstart, kend - kstart);
                return;
        }

        /*
         * Case: Kernel Vaddr (0x7000_0000 to 0x7fff_ffff)
         * (1) ARC Cache Maintenance ops only take Phy addr, hence special
         *     handling of kernel vaddr.
         *
         * (2) Despite @tot_sz being < PAGE_SIZE (bigger cases handled already),
         *     it still needs to handle  a 2 page scenario, where the range
         *     straddles across 2 virtual pages and hence need for loop
         */
        while (tot_sz > 0) {
                off = kstart % PAGE_SIZE;
                pfn = vmalloc_to_pfn((void *)kstart);
                phy = (pfn << PAGE_SHIFT) + off;
                sz = min_t(unsigned int, tot_sz, PAGE_SIZE - off);
                __sync_icache_dcache(phy, kstart, sz);
                kstart += sz;
                tot_sz -= sz;
        }
}

/*
 * General purpose helper to make I and D cache lines consistent.
 * @paddr is phy addr of region
 * @vaddr is typically user vaddr (breakpoint) or kernel vaddr (vmalloc)
 *    However in one instance, when called by kprobe (for a breakpt in
 *    builtin kernel code) @vaddr will be paddr only, meaning CDU operation will
 *    use a paddr to index the cache (despite VIPT). This is fine since since a
 *    builtin kernel page will not have any virtual mappings.
 *    kprobe on loadable module will be kernel vaddr.
 */
void __sync_icache_dcache(unsigned long paddr, unsigned long vaddr, int len)
{
        __dc_line_op(paddr, vaddr, len, OP_FLUSH_N_INV);
        __ic_line_inv_vaddr(paddr, vaddr, len);
}

/* wrapper to compile time eliminate alignment checks in flush loop */
void __inv_icache_page(unsigned long paddr, unsigned long vaddr)
{
        __ic_line_inv_vaddr(paddr, vaddr, PAGE_SIZE);
}

/*
 * wrapper to clearout kernel or userspace mappings of a page
 * For kernel mappings @vaddr == @paddr
 */
void ___flush_dcache_page(unsigned long paddr, unsigned long vaddr)
{
        __dc_line_op(paddr, vaddr & PAGE_MASK, PAGE_SIZE, OP_FLUSH_N_INV);
}

noinline void flush_cache_all(void)
{
        unsigned long flags;

        local_irq_save(flags);

        __ic_entire_inv();
        __dc_entire_op(OP_FLUSH_N_INV);

        local_irq_restore(flags);

}

#ifdef CONFIG_ARC_CACHE_VIPT_ALIASING

void flush_cache_mm(struct mm_struct *mm)
{
        flush_cache_all();
}

void flush_cache_page(struct vm_area_struct *vma, unsigned long u_vaddr,
                      unsigned long pfn)
{
        unsigned int paddr = pfn << PAGE_SHIFT;

        u_vaddr &= PAGE_MASK;

        ___flush_dcache_page(paddr, u_vaddr);

        if (vma->vm_flags & VM_EXEC)
                __inv_icache_page(paddr, u_vaddr);
}

void flush_cache_range(struct vm_area_struct *vma, unsigned long start,
                       unsigned long end)
{
        flush_cache_all();
}

void flush_anon_page(struct vm_area_struct *vma, struct page *page,
                     unsigned long u_vaddr)
{
        /* TBD: do we really need to clear the kernel mapping */
        __flush_dcache_page(page_address(page), u_vaddr);
        __flush_dcache_page(page_address(page), page_address(page));

}

#endif

void copy_user_highpage(struct page *to, struct page *from,
        unsigned long u_vaddr, struct vm_area_struct *vma)
{
        void *kfrom = page_address(from);
        void *kto = page_address(to);
        int clean_src_k_mappings = 0;

        /*
         * If SRC page was already mapped in userspace AND it's U-mapping is
         * not congruent with K-mapping, sync former to physical page so that
         * K-mapping in memcpy below, sees the right data
         *
         * Note that while @u_vaddr refers to DST page's userspace vaddr, it is
         * equally valid for SRC page as well
         */
        if (page_mapped(from) && addr_not_cache_congruent(kfrom, u_vaddr)) {
                __flush_dcache_page(kfrom, u_vaddr);
                clean_src_k_mappings = 1;
        }

        copy_page(kto, kfrom);

        /*
         * Mark DST page K-mapping as dirty for a later finalization by
         * update_mmu_cache(). Although the finalization could have been done
         * here as well (given that both vaddr/paddr are available).
         * But update_mmu_cache() already has code to do that for other
         * non copied user pages (e.g. read faults which wire in pagecache page
         * directly).
         */
        clear_bit(PG_dc_clean, &to->flags);

        /*
         * if SRC was already usermapped and non-congruent to kernel mapping
         * sync the kernel mapping back to physical page
         */
        if (clean_src_k_mappings) {
                __flush_dcache_page(kfrom, kfrom);
                set_bit(PG_dc_clean, &from->flags);
        } else {
                clear_bit(PG_dc_clean, &from->flags);
        }
}

void clear_user_page(void *to, unsigned long u_vaddr, struct page *page)
{
        clear_page(to);
        clear_bit(PG_dc_clean, &page->flags);
}


/**********************************************************************
 * Explicit Cache flush request from user space via syscall
 * Needed for JITs which generate code on the fly
 */
SYSCALL_DEFINE3(cacheflush, uint32_t, start, uint32_t, sz, uint32_t, flags)
{
        /* TBD: optimize this */
        flush_cache_all();
        return 0;
}