2 * Copyright 2012 ST-Ericsson AB
4 * The code contained herein is licensed under the GNU General Public
5 * License. You may obtain a copy of the GNU General Public License
6 * Version 2 or later at the following locations:
8 * http://www.opensource.org/licenses/gpl-license.html
9 * http://www.gnu.org/copyleft/gpl.html
11 * Device Tree for the TVK1281618 UIB
14 #include <dt-bindings/interrupt-controller/irq.h>
18 compatible = "gpio-keys";
21 vdd-supply = <&ab8500_ldo_aux1_reg>;
22 pinctrl-names = "default";
23 pinctrl-0 = <&prox_tvk_mode>, <&hall_tvk_mode>;
26 /* Proximity sensor */
27 gpios = <&gpio6 25 0x4>;
28 linux,code = <11>; /* SW_FRONT_PROXIMITY */
29 label = "SFH7741 Proximity Sensor";
33 gpios = <&gpio4 17 0x4>;
34 linux,code = <0>; /* SW_LID */
35 label = "HED54XXU11 Hall Effect Sensor";
42 compatible = "toshiba,tc35893";
44 interrupt-parent = <&gpio6>;
45 interrupts = <26 IRQ_TYPE_EDGE_RISING>;
46 pinctrl-names = "default";
47 pinctrl-0 = <&tc35893_tvk_mode>;
50 #interrupt-cells = <1>;
53 compatible = "toshiba,tc3589x-gpio";
57 #interrupt-cells = <2>;
62 compatible = "toshiba,tc3589x-keypad";
64 debounce-delay-ms = <4>;
65 keypad,num-columns = <8>;
66 keypad,num-rows = <8>;
69 linux,keymap = <0x0301006b
90 /* Sensors mounted on this board variant */
94 compatible = "st,lsm303dlh-accel";
95 st,drdy-int-pin = <1>;
97 vdd-supply = <&ab8500_ldo_aux1_reg>;
98 vddio-supply = <&db8500_vsmps2_reg>;
99 pinctrl-names = "default";
100 pinctrl-0 = <&accel_tvk_mode>;
101 interrupt-parent = <&gpio2>;
102 interrupts = <18 IRQ_TYPE_EDGE_RISING>,
103 <19 IRQ_TYPE_EDGE_RISING>;
107 * This magnetometer is packaged with
108 * the accelerometer, and has a DRDY line,
109 * however it is not connected on this
110 * board so it can not generate interrupts.
112 compatible = "st,lsm303dlh-magn";
114 vdd-supply = <&ab8500_ldo_aux1_reg>;
115 vddio-supply = <&db8500_vsmps2_reg>;
119 compatible = "st,lis331dl-accel";
120 st,drdy-int-pin = <1>;
122 vdd-supply = <&ab8500_ldo_aux1_reg>;
123 vddio-supply = <&db8500_vsmps2_reg>;
124 pinctrl-names = "default";
125 pinctrl-0 = <&accel_tvk_mode>;
126 interrupt-parent = <&gpio2>;
127 interrupts = <18 IRQ_TYPE_EDGE_RISING>,
128 <19 IRQ_TYPE_EDGE_RISING>;
132 compatible = "asahi-kasei,ak8974";
134 vdd-supply = <&ab8500_ldo_aux1_reg>;
135 vddio-supply = <&db8500_vsmps2_reg>;
136 pinctrl-names = "default";
137 pinctrl-0 = <&gyro_magn_tvk_mode>;
138 interrupt-parent = <&gpio1>;
139 interrupts = <0 IRQ_TYPE_EDGE_RISING>;
143 compatible = "st,l3g4200d-gyro";
144 st,drdy-int-pin = <2>;
146 vdd-supply = <&ab8500_ldo_aux1_reg>;
147 vddio-supply = <&db8500_vsmps2_reg>;
148 pinctrl-names = "default";
149 pinctrl-0 = <&gyro_magn_tvk_mode>;
150 interrupt-parent = <&gpio1>;
151 interrupts = <0 IRQ_TYPE_EDGE_RISING>;
154 /* Barometer/pressure sensor */
155 compatible = "st,lps001wp-press";
157 vdd-supply = <&ab8500_ldo_aux1_reg>;
158 vddio-supply = <&db8500_vsmps2_reg>;
164 /* Synaptics RMI4 TM1217 touchscreen */
165 compatible = "syna,rmi4-i2c";
166 #address-cells = <1>;
169 vdd-supply = <&ab8500_ldo_aux1_reg>;
170 vddio-supply = <&db8500_vsmps2_reg>;
171 pinctrl-names = "default";
172 pinctrl-0 = <&synaptics_tvk_mode>;
173 interrupt-parent = <&gpio2>;
174 interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
182 touchscreen-inverted-x;
183 syna,sensor-type = <1>;
189 /* Pull up this GPIO pin */
191 tc35893_tvk_mode: tc35893_tvk {
193 pins = "GPIO218_AH11";
194 ste,config = <&gpio_in_pu>;
199 prox_tvk_mode: prox_tvk {
201 pins = "GPIO217_AH12";
202 ste,config = <&gpio_in_pu>;
207 hall_tvk_mode: hall_tvk {
209 pins = "GPIO145_C13";
210 ste,config = <&gpio_in_pu>;
215 accel_tvk_mode: accel_tvk {
216 /* Accelerometer interrupt lines 1 & 2 */
218 pins = "GPIO82_C1", "GPIO83_D3";
219 ste,config = <&gpio_in_pd>;
225 * These lines are shared between Gyroscope l3g400dh
226 * and AK8974 magnetometer.
228 gyro_magn_tvk_mode: gyro_magn_tvk {
229 /* GPIO 31 used for INT pull down the line */
232 ste,config = <&gpio_in_pd>;
234 /* GPIO 32 used for DRDY, pull this down */
237 ste,config = <&gpio_in_pd>;
242 synaptics_tvk_mode: synaptics_tvk {
243 /* Touchscreen uses GPIO 84 */
246 ste,config = <&gpio_in_pu>;