2 * linux/arch/arm/mach-at91/board-rm9200ek.c
4 * Copyright (C) 2005 SAN People
6 * Epson S1D framebuffer glue code is:
7 * Copyright (C) 2005 Thibaut VARENE <varenet@parisc-linux.org>
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License as published by
11 * the Free Software Foundation; either version 2 of the License, or
12 * (at your option) any later version.
14 * This program is distributed in the hope that it will be useful,
15 * but WITHOUT ANY WARRANTY; without even the implied warranty of
16 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
17 * GNU General Public License for more details.
19 * You should have received a copy of the GNU General Public License
20 * along with this program; if not, write to the Free Software
21 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
24 #include <linux/types.h>
25 #include <linux/gpio.h>
26 #include <linux/init.h>
28 #include <linux/module.h>
29 #include <linux/platform_device.h>
30 #include <linux/spi/spi.h>
31 #include <linux/mtd/physmap.h>
33 #include <asm/setup.h>
34 #include <asm/mach-types.h>
37 #include <asm/mach/arch.h>
38 #include <asm/mach/map.h>
39 #include <asm/mach/irq.h>
41 #include <mach/hardware.h>
42 #include <mach/board.h>
43 #include <mach/at91rm9200_mc.h>
44 #include <mach/at91_ramc.h>
49 static void __init
ek_init_early(void)
51 /* Initialize processor: 18.432 MHz crystal */
52 at91_initialize(18432000);
55 static struct macb_platform_data __initdata ek_eth_data
= {
56 .phy_irq_pin
= AT91_PIN_PC4
,
60 static struct at91_usbh_data __initdata ek_usbh_data
= {
62 .vbus_pin
= {-EINVAL
, -EINVAL
},
63 .overcurrent_pin
= {-EINVAL
, -EINVAL
},
66 static struct at91_udc_data __initdata ek_udc_data
= {
67 .vbus_pin
= AT91_PIN_PD4
,
68 .pullup_pin
= AT91_PIN_PD5
,
71 #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
72 static struct at91_mmc_data __initdata ek_mmc_data
= {
73 .det_pin
= AT91_PIN_PB27
,
76 .wp_pin
= AT91_PIN_PA17
,
81 static struct spi_board_info ek_spi_devices
[] = {
82 { /* DataFlash chip */
83 .modalias
= "mtd_dataflash",
85 .max_speed_hz
= 15 * 1000 * 1000,
87 #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
88 { /* DataFlash card */
89 .modalias
= "mtd_dataflash",
91 .max_speed_hz
= 15 * 1000 * 1000,
96 static struct i2c_board_info __initdata ek_i2c_devices
[] = {
98 I2C_BOARD_INFO("ics1523", 0x26),
101 I2C_BOARD_INFO("dac3550", 0x4d),
105 #define EK_FLASH_BASE AT91_CHIPSELECT_0
106 #define EK_FLASH_SIZE SZ_8M
108 static struct physmap_flash_data ek_flash_data
= {
112 static struct resource ek_flash_resource
= {
113 .start
= EK_FLASH_BASE
,
114 .end
= EK_FLASH_BASE
+ EK_FLASH_SIZE
- 1,
115 .flags
= IORESOURCE_MEM
,
118 static struct platform_device ek_flash
= {
119 .name
= "physmap-flash",
122 .platform_data
= &ek_flash_data
,
124 .resource
= &ek_flash_resource
,
128 static struct gpio_led ek_leds
[] = {
129 { /* "user led 1", DS2 */
131 .gpio
= AT91_PIN_PB0
,
133 .default_trigger
= "mmc0",
135 { /* "user led 2", DS4 */
137 .gpio
= AT91_PIN_PB1
,
139 .default_trigger
= "heartbeat",
141 { /* "user led 3", DS6 */
143 .gpio
= AT91_PIN_PB2
,
148 static void __init
ek_board_init(void)
151 at91_init_leds(AT91_PIN_PB1
, AT91_PIN_PB2
);
154 /* DBGU on ttyS0. (Rx & Tx only) */
155 at91_register_uart(0, 0, 0);
157 /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */
158 at91_register_uart(AT91RM9200_ID_US1
, 1, ATMEL_UART_CTS
| ATMEL_UART_RTS
159 | ATMEL_UART_DTR
| ATMEL_UART_DSR
| ATMEL_UART_DCD
161 at91_add_device_serial();
163 at91_add_device_eth(&ek_eth_data
);
165 at91_add_device_usbh(&ek_usbh_data
);
167 at91_add_device_udc(&ek_udc_data
);
168 at91_set_multi_drive(ek_udc_data
.pullup_pin
, 1); /* pullup_pin is connected to reset */
170 at91_add_device_i2c(ek_i2c_devices
, ARRAY_SIZE(ek_i2c_devices
));
172 at91_add_device_spi(ek_spi_devices
, ARRAY_SIZE(ek_spi_devices
));
173 #ifdef CONFIG_MTD_AT91_DATAFLASH_CARD
175 at91_set_gpio_output(AT91_PIN_PB22
, 0);
178 at91_set_gpio_output(AT91_PIN_PB22
, 1); /* this MMC card slot can optionally use SPI signaling (CS3). */
179 at91_add_device_mmc(0, &ek_mmc_data
);
182 platform_device_register(&ek_flash
);
184 at91_gpio_leds(ek_leds
, ARRAY_SIZE(ek_leds
));
186 // ek_add_device_video();
189 MACHINE_START(AT91RM9200EK
, "Atmel AT91RM9200-EK")
190 /* Maintainer: SAN People/Atmel */
191 .timer
= &at91rm9200_timer
,
192 .map_io
= at91_map_io
,
193 .init_early
= ek_init_early
,
194 .init_irq
= at91_init_irq_default
,
195 .init_machine
= ek_board_init
,