arch/arm/mach-davinci/Kconfig

   1 if ARCH_DAVINCI
   2
   3 config AINTC
   4         bool
   5
   6 config CP_INTC
   7         bool
   8         select IRQ_DOMAIN
   9
  10 config ARCH_DAVINCI_DMx
  11         bool
  12         select CPU_ARM926T
  13
  14 menu "TI DaVinci Implementations"
  15
  16 comment "DaVinci Core Type"
  17
  18 config ARCH_DAVINCI_DM644x
  19         bool "DaVinci 644x based system"
  20         select AINTC
  21         select ARCH_DAVINCI_DMx
  22
  23 config ARCH_DAVINCI_DM355
  24         bool "DaVinci 355 based system"
  25         select AINTC
  26         select ARCH_DAVINCI_DMx
  27
  28 config ARCH_DAVINCI_DM646x
  29         bool "DaVinci 646x based system"
  30         select AINTC
  31         select ARCH_DAVINCI_DMx
  32
  33 config ARCH_DAVINCI_DA830
  34         bool "DA830/OMAP-L137/AM17x based system"
  35         select ARCH_DAVINCI_DA8XX
  36         select CPU_DCACHE_WRITETHROUGH # needed on silicon revs 1.0, 1.1
  37         select CP_INTC
  38
  39 config ARCH_DAVINCI_DA850
  40         bool "DA850/OMAP-L138/AM18x based system"
  41         select ARCH_DAVINCI_DA8XX
  42         select ARCH_HAS_CPUFREQ
  43         select CP_INTC
  44
  45 config ARCH_DAVINCI_DA8XX
  46         bool
  47         select CPU_ARM926T
  48
  49 config ARCH_DAVINCI_DM365
  50         bool "DaVinci 365 based system"
  51         select AINTC
  52         select ARCH_DAVINCI_DMx
  53
  54 config ARCH_DAVINCI_TNETV107X
  55         bool "TNETV107X based system"
  56         select CPU_V6
  57         select CP_INTC
  58
  59 comment "DaVinci Board Type"
  60
  61 config MACH_DA8XX_DT
  62         bool "Support DA8XX platforms using device tree"
  63         default y
  64         depends on ARCH_DAVINCI_DA8XX
  65         select PINCTRL
  66         help
  67           Say y here to include support for TI DaVinci DA850 based using
  68           Flattened Device Tree. More information at Documentation/devicetree
  69
  70 config MACH_DAVINCI_EVM
  71         bool "TI DM644x EVM"
  72         default ARCH_DAVINCI_DM644x
  73         depends on ARCH_DAVINCI_DM644x
  74         select EEPROM_AT24
  75         select I2C
  76         help
  77           Configure this option to specify the whether the board used
  78           for development is a DM644x EVM
  79
  80 config MACH_SFFSDR
  81         bool "Lyrtech SFFSDR"
  82         depends on ARCH_DAVINCI_DM644x
  83         select EEPROM_AT24
  84         select I2C
  85         help
  86           Say Y here to select the Lyrtech Small Form Factor
  87           Software Defined Radio (SFFSDR) board.
  88
  89 config MACH_NEUROS_OSD2
  90         bool "Neuros OSD2 Open Television Set Top Box"
  91         depends on ARCH_DAVINCI_DM644x
  92         help
  93           Configure this option to specify the whether the board used
  94           for development is a Neuros OSD2 Open Set Top Box.
  95
  96 config MACH_DAVINCI_DM355_EVM
  97         bool "TI DM355 EVM"
  98         default ARCH_DAVINCI_DM355
  99         depends on ARCH_DAVINCI_DM355
 100         help
 101           Configure this option to specify the whether the board used
 102           for development is a DM355 EVM
 103
 104 config MACH_DM355_LEOPARD
 105         bool "DM355 Leopard board"
 106         depends on ARCH_DAVINCI_DM355
 107         help
 108           Configure this option to specify the whether the board used
 109           for development is a DM355 Leopard board.
 110
 111 config MACH_DAVINCI_DM6467_EVM
 112         bool "TI DM6467 EVM"
 113         default ARCH_DAVINCI_DM646x
 114         depends on ARCH_DAVINCI_DM646x
 115         select EEPROM_AT24
 116         select I2C
 117         select MACH_DAVINCI_DM6467TEVM
 118         help
 119           Configure this option to specify the whether the board used
 120           for development is a DM6467 EVM
 121
 122 config MACH_DAVINCI_DM6467TEVM
 123         bool
 124
 125 config MACH_DAVINCI_DM365_EVM
 126         bool "TI DM365 EVM"
 127         default ARCH_DAVINCI_DM365
 128         depends on ARCH_DAVINCI_DM365
 129         select EEPROM_AT24
 130         select I2C
 131         help
 132           Configure this option to specify whether the board used
 133           for development is a DM365 EVM
 134
 135 config MACH_DAVINCI_DA830_EVM
 136         bool "TI DA830/OMAP-L137/AM17x Reference Platform"
 137         default ARCH_DAVINCI_DA830
 138         depends on ARCH_DAVINCI_DA830
 139         select EEPROM_AT24
 140         select GPIO_PCF857X
 141         select I2C
 142         help
 143           Say Y here to select the TI DA830/OMAP-L137/AM17x Evaluation Module.
 144
 145 choice
 146         prompt "Select DA830/OMAP-L137/AM17x UI board peripheral"
 147         depends on MACH_DAVINCI_DA830_EVM
 148         help
 149           The presence of UI card on the DA830/OMAP-L137/AM17x EVM is
 150           detected automatically based on successful probe of the I2C
 151           based GPIO expander on that board. This option selected in this
 152           menu has an effect only in case of a successful UI card detection.
 153
 154 config DA830_UI_LCD
 155         bool "LCD"
 156         help
 157           Say Y here to use the LCD as a framebuffer or simple character
 158           display.
 159
 160 config DA830_UI_NAND
 161         bool "NAND flash"
 162         help
 163           Say Y here to use the NAND flash. Do not forget to setup
 164           the switch correctly.
 165 endchoice
 166
 167 config MACH_DAVINCI_DA850_EVM
 168         bool "TI DA850/OMAP-L138/AM18x Reference Platform"
 169         default ARCH_DAVINCI_DA850
 170         depends on ARCH_DAVINCI_DA850
 171         help
 172           Say Y here to select the TI DA850/OMAP-L138/AM18x Evaluation Module.
 173
 174 choice
 175         prompt "Select peripherals connected to expander on UI board"
 176         depends on MACH_DAVINCI_DA850_EVM
 177         help
 178           The presence of User Interface (UI) card on the DA850/OMAP-L138/AM18x
 179           EVM is detected automatically based on successful probe of the I2C
 180           based GPIO expander on that card. This option selected in this
 181           menu has an effect only in case of a successful UI card detection.
 182
 183 config DA850_UI_NONE
 184         bool "No peripheral is enabled"
 185         help
 186           Say Y if you do not want to enable any of the peripherals connected
 187           to TCA6416 expander on DA850/OMAP-L138/AM18x EVM UI card
 188
 189 config DA850_UI_RMII
 190         bool "RMII Ethernet PHY"
 191         help
 192           Say Y if you want to use the RMII PHY on the DA850/OMAP-L138/AM18x
 193           EVM. This PHY is found on the UI daughter card that is supplied with
 194           the EVM.
 195           NOTE: Please take care while choosing this option, MII PHY will
 196           not be functional if RMII mode is selected.
 197
 198 config DA850_UI_SD_VIDEO_PORT
 199         bool "Video Port Interface"
 200         help
 201           Say Y if you want to use Video Port Interface (VPIF) on the
 202           DA850/OMAP-L138 EVM. The Video decoders/encoders are found on the
 203           UI daughter card that is supplied with the EVM.
 204
 205 endchoice
 206
 207 config DA850_WL12XX
 208         bool "AM18x wl1271 daughter board"
 209         depends on MACH_DAVINCI_DA850_EVM
 210         help
 211           The wl1271 daughter card for AM18x EVMs is a combo wireless
 212           connectivity add-on card, based on the LS Research TiWi module with
 213           Texas Instruments' wl1271 solution.
 214           Say Y if you want to use a wl1271 expansion card connected to the
 215           AM18x EVM.
 216
 217 config GPIO_PCA953X
 218         default MACH_DAVINCI_DA850_EVM
 219
 220 config KEYBOARD_GPIO_POLLED
 221         default MACH_DAVINCI_DA850_EVM
 222
 223 config MACH_TNETV107X
 224         bool "TI TNETV107X Reference Platform"
 225         default ARCH_DAVINCI_TNETV107X
 226         depends on ARCH_DAVINCI_TNETV107X
 227         help
 228           Say Y here to select the TI TNETV107X Evaluation Module.
 229
 230 config MACH_MITYOMAPL138
 231         bool "Critical Link MityDSP-L138/MityARM-1808 SoM"
 232         depends on ARCH_DAVINCI_DA850
 233         select EEPROM_AT24
 234         select I2C
 235         help
 236           Say Y here to select the Critical Link MityDSP-L138/MityARM-1808
 237           System on Module.  Information on this SoM may be found at
 238           http://www.mitydsp.com
 239
 240 config MACH_OMAPL138_HAWKBOARD
 241         bool "TI AM1808 / OMAPL-138 Hawkboard platform"
 242         depends on ARCH_DAVINCI_DA850
 243         help
 244           Say Y here to select the TI AM1808 / OMAPL-138 Hawkboard platform .
 245           Information of this board may be found at
 246           http://www.hawkboard.org/
 247
 248 config DAVINCI_MUX
 249         bool "DAVINCI multiplexing support"
 250         depends on ARCH_DAVINCI
 251         default y
 252         help
 253           Pin multiplexing support for DAVINCI boards. If your bootloader
 254           sets the multiplexing correctly, say N. Otherwise, or if unsure,
 255           say Y.
 256
 257 config DAVINCI_MUX_DEBUG
 258         bool "Multiplexing debug output"
 259         depends on DAVINCI_MUX
 260         help
 261           Makes the multiplexing functions print out a lot of debug info.
 262           This is useful if you want to find out the correct values of the
 263           multiplexing registers.
 264
 265 config DAVINCI_MUX_WARNINGS
 266         bool "Warn about pins the bootloader didn't set up"
 267         depends on DAVINCI_MUX
 268         help
 269           Choose Y here to warn whenever driver initialization logic needs
 270           to change the pin multiplexing setup. When there are no warnings
 271           printed, it's safe to deselect DAVINCI_MUX for your product.
 272
 273 config DAVINCI_RESET_CLOCKS
 274         bool "Reset unused clocks during boot"
 275         depends on ARCH_DAVINCI
 276         help
 277           Say Y if you want to reset unused clocks during boot.
 278           This option saves power, but assumes all drivers are
 279           using the clock framework. Broken drivers that do not
 280           yet use clock framework may not work with this option.
 281           If you are booting from another operating system, you
 282           probably do not want this option enabled until your
 283           device drivers work properly.
 284
 285 endmenu
 286
 287 endif