arch/arm/mach-davinci/Kconfig

   1 if ARCH_DAVINCI
   2
   3 config AINTC
   4         bool
   5
   6 config CP_INTC
   7         bool
   8         select IRQ_DOMAIN
   9
  10 config ARCH_DAVINCI_DMx
  11         bool
  12         select CPU_ARM926T
  13
  14 menu "TI DaVinci Implementations"
  15
  16 comment "DaVinci Core Type"
  17
  18 config ARCH_DAVINCI_DM644x
  19         bool "DaVinci 644x based system"
  20         select AINTC
  21         select ARCH_DAVINCI_DMx
  22
  23 config ARCH_DAVINCI_DM355
  24         bool "DaVinci 355 based system"
  25         select AINTC
  26         select ARCH_DAVINCI_DMx
  27
  28 config ARCH_DAVINCI_DM646x
  29         bool "DaVinci 646x based system"
  30         select AINTC
  31         select ARCH_DAVINCI_DMx
  32
  33 config ARCH_DAVINCI_DA830
  34         bool "DA830/OMAP-L137/AM17x based system"
  35         select ARCH_DAVINCI_DA8XX
  36         select CPU_DCACHE_WRITETHROUGH # needed on silicon revs 1.0, 1.1
  37         select CP_INTC
  38
  39 config ARCH_DAVINCI_DA850
  40         bool "DA850/OMAP-L138/AM18x based system"
  41         select ARCH_DAVINCI_DA8XX
  42         select ARCH_HAS_CPUFREQ
  43         select CP_INTC
  44
  45 config ARCH_DAVINCI_DA8XX
  46         bool
  47         select CPU_ARM926T
  48
  49 config ARCH_DAVINCI_DM365
  50         bool "DaVinci 365 based system"
  51         select AINTC
  52         select ARCH_DAVINCI_DMx
  53
  54 comment "DaVinci Board Type"
  55
  56 config MACH_DA8XX_DT
  57         bool "Support DA8XX platforms using device tree"
  58         default y
  59         depends on ARCH_DAVINCI_DA8XX
  60         select PINCTRL
  61         help
  62           Say y here to include support for TI DaVinci DA850 based using
  63           Flattened Device Tree. More information at Documentation/devicetree
  64
  65 config MACH_DAVINCI_EVM
  66         bool "TI DM644x EVM"
  67         default ARCH_DAVINCI_DM644x
  68         depends on ARCH_DAVINCI_DM644x
  69         select EEPROM_AT24
  70         select I2C
  71         help
  72           Configure this option to specify the whether the board used
  73           for development is a DM644x EVM
  74
  75 config MACH_SFFSDR
  76         bool "Lyrtech SFFSDR"
  77         depends on ARCH_DAVINCI_DM644x
  78         select EEPROM_AT24
  79         select I2C
  80         help
  81           Say Y here to select the Lyrtech Small Form Factor
  82           Software Defined Radio (SFFSDR) board.
  83
  84 config MACH_NEUROS_OSD2
  85         bool "Neuros OSD2 Open Television Set Top Box"
  86         depends on ARCH_DAVINCI_DM644x
  87         help
  88           Configure this option to specify the whether the board used
  89           for development is a Neuros OSD2 Open Set Top Box.
  90
  91 config MACH_DAVINCI_DM355_EVM
  92         bool "TI DM355 EVM"
  93         default ARCH_DAVINCI_DM355
  94         depends on ARCH_DAVINCI_DM355
  95         help
  96           Configure this option to specify the whether the board used
  97           for development is a DM355 EVM
  98
  99 config MACH_DM355_LEOPARD
 100         bool "DM355 Leopard board"
 101         depends on ARCH_DAVINCI_DM355
 102         help
 103           Configure this option to specify the whether the board used
 104           for development is a DM355 Leopard board.
 105
 106 config MACH_DAVINCI_DM6467_EVM
 107         bool "TI DM6467 EVM"
 108         default ARCH_DAVINCI_DM646x
 109         depends on ARCH_DAVINCI_DM646x
 110         select EEPROM_AT24
 111         select I2C
 112         select MACH_DAVINCI_DM6467TEVM
 113         help
 114           Configure this option to specify the whether the board used
 115           for development is a DM6467 EVM
 116
 117 config MACH_DAVINCI_DM6467TEVM
 118         bool
 119
 120 config MACH_DAVINCI_DM365_EVM
 121         bool "TI DM365 EVM"
 122         default ARCH_DAVINCI_DM365
 123         depends on ARCH_DAVINCI_DM365
 124         select EEPROM_AT24
 125         select I2C
 126         help
 127           Configure this option to specify whether the board used
 128           for development is a DM365 EVM
 129
 130 config MACH_DAVINCI_DA830_EVM
 131         bool "TI DA830/OMAP-L137/AM17x Reference Platform"
 132         default ARCH_DAVINCI_DA830
 133         depends on ARCH_DAVINCI_DA830
 134         select EEPROM_AT24
 135         select GPIO_PCF857X
 136         select I2C
 137         help
 138           Say Y here to select the TI DA830/OMAP-L137/AM17x Evaluation Module.
 139
 140 choice
 141         prompt "Select DA830/OMAP-L137/AM17x UI board peripheral"
 142         depends on MACH_DAVINCI_DA830_EVM
 143         help
 144           The presence of UI card on the DA830/OMAP-L137/AM17x EVM is
 145           detected automatically based on successful probe of the I2C
 146           based GPIO expander on that board. This option selected in this
 147           menu has an effect only in case of a successful UI card detection.
 148
 149 config DA830_UI_LCD
 150         bool "LCD"
 151         help
 152           Say Y here to use the LCD as a framebuffer or simple character
 153           display.
 154
 155 config DA830_UI_NAND
 156         bool "NAND flash"
 157         help
 158           Say Y here to use the NAND flash. Do not forget to setup
 159           the switch correctly.
 160 endchoice
 161
 162 config MACH_DAVINCI_DA850_EVM
 163         bool "TI DA850/OMAP-L138/AM18x Reference Platform"
 164         default ARCH_DAVINCI_DA850
 165         depends on ARCH_DAVINCI_DA850
 166         help
 167           Say Y here to select the TI DA850/OMAP-L138/AM18x Evaluation Module.
 168
 169 choice
 170         prompt "Select peripherals connected to expander on UI board"
 171         depends on MACH_DAVINCI_DA850_EVM
 172         help
 173           The presence of User Interface (UI) card on the DA850/OMAP-L138/AM18x
 174           EVM is detected automatically based on successful probe of the I2C
 175           based GPIO expander on that card. This option selected in this
 176           menu has an effect only in case of a successful UI card detection.
 177
 178 config DA850_UI_NONE
 179         bool "No peripheral is enabled"
 180         help
 181           Say Y if you do not want to enable any of the peripherals connected
 182           to TCA6416 expander on DA850/OMAP-L138/AM18x EVM UI card
 183
 184 config DA850_UI_RMII
 185         bool "RMII Ethernet PHY"
 186         help
 187           Say Y if you want to use the RMII PHY on the DA850/OMAP-L138/AM18x
 188           EVM. This PHY is found on the UI daughter card that is supplied with
 189           the EVM.
 190           NOTE: Please take care while choosing this option, MII PHY will
 191           not be functional if RMII mode is selected.
 192
 193 config DA850_UI_SD_VIDEO_PORT
 194         bool "Video Port Interface"
 195         help
 196           Say Y if you want to use Video Port Interface (VPIF) on the
 197           DA850/OMAP-L138 EVM. The Video decoders/encoders are found on the
 198           UI daughter card that is supplied with the EVM.
 199
 200 endchoice
 201
 202 config DA850_WL12XX
 203         bool "AM18x wl1271 daughter board"
 204         depends on MACH_DAVINCI_DA850_EVM
 205         help
 206           The wl1271 daughter card for AM18x EVMs is a combo wireless
 207           connectivity add-on card, based on the LS Research TiWi module with
 208           Texas Instruments' wl1271 solution.
 209           Say Y if you want to use a wl1271 expansion card connected to the
 210           AM18x EVM.
 211
 212
 213 config MACH_MITYOMAPL138
 214         bool "Critical Link MityDSP-L138/MityARM-1808 SoM"
 215         depends on ARCH_DAVINCI_DA850
 216         select EEPROM_AT24
 217         select I2C
 218         help
 219           Say Y here to select the Critical Link MityDSP-L138/MityARM-1808
 220           System on Module.  Information on this SoM may be found at
 221           http://www.mitydsp.com
 222
 223 config MACH_OMAPL138_HAWKBOARD
 224         bool "TI AM1808 / OMAPL-138 Hawkboard platform"
 225         depends on ARCH_DAVINCI_DA850
 226         help
 227           Say Y here to select the TI AM1808 / OMAPL-138 Hawkboard platform .
 228           Information of this board may be found at
 229           http://www.hawkboard.org/
 230
 231 config DAVINCI_MUX
 232         bool "DAVINCI multiplexing support"
 233         depends on ARCH_DAVINCI
 234         default y
 235         help
 236           Pin multiplexing support for DAVINCI boards. If your bootloader
 237           sets the multiplexing correctly, say N. Otherwise, or if unsure,
 238           say Y.
 239
 240 config DAVINCI_MUX_DEBUG
 241         bool "Multiplexing debug output"
 242         depends on DAVINCI_MUX
 243         help
 244           Makes the multiplexing functions print out a lot of debug info.
 245           This is useful if you want to find out the correct values of the
 246           multiplexing registers.
 247
 248 config DAVINCI_MUX_WARNINGS
 249         bool "Warn about pins the bootloader didn't set up"
 250         depends on DAVINCI_MUX
 251         help
 252           Choose Y here to warn whenever driver initialization logic needs
 253           to change the pin multiplexing setup. When there are no warnings
 254           printed, it's safe to deselect DAVINCI_MUX for your product.
 255
 256 config DAVINCI_RESET_CLOCKS
 257         bool "Reset unused clocks during boot"
 258         depends on ARCH_DAVINCI
 259         help
 260           Say Y if you want to reset unused clocks during boot.
 261           This option saves power, but assumes all drivers are
 262           using the clock framework. Broken drivers that do not
 263           yet use clock framework may not work with this option.
 264           If you are booting from another operating system, you
 265           probably do not want this option enabled until your
 266           device drivers work properly.
 267
 268 endmenu
 269
 270 endif