10 config ARCH_DAVINCI_DMx
14 menu "TI DaVinci Implementations"
16 comment "DaVinci Core Type"
18 config ARCH_DAVINCI_DM644x
19 bool "DaVinci 644x based system"
21 select ARCH_DAVINCI_DMx
23 config ARCH_DAVINCI_DM355
24 bool "DaVinci 355 based system"
26 select ARCH_DAVINCI_DMx
28 config ARCH_DAVINCI_DM646x
29 bool "DaVinci 646x based system"
31 select ARCH_DAVINCI_DMx
33 config ARCH_DAVINCI_DA830
34 bool "DA830/OMAP-L137/AM17x based system"
35 depends on !ARCH_DAVINCI_DMx || AUTO_ZRELADDR
36 select ARCH_DAVINCI_DA8XX
37 # needed on silicon revs 1.0, 1.1:
38 select CPU_DCACHE_WRITETHROUGH if !CPU_DCACHE_DISABLE
41 config ARCH_DAVINCI_DA850
42 bool "DA850/OMAP-L138/AM18x based system"
43 depends on !ARCH_DAVINCI_DMx || AUTO_ZRELADDR
44 select ARCH_DAVINCI_DA8XX
47 config ARCH_DAVINCI_DA8XX
51 config ARCH_DAVINCI_DM365
52 bool "DaVinci 365 based system"
54 select ARCH_DAVINCI_DMx
56 comment "DaVinci Board Type"
59 bool "Support DA8XX platforms using device tree"
61 depends on ARCH_DAVINCI_DA8XX
64 Say y here to include support for TI DaVinci DA850 based using
65 Flattened Device Tree. More information at Documentation/devicetree
67 config MACH_DAVINCI_EVM
69 default ARCH_DAVINCI_DM644x
70 depends on ARCH_DAVINCI_DM644x
74 Configure this option to specify the whether the board used
75 for development is a DM644x EVM
79 depends on ARCH_DAVINCI_DM644x
83 Say Y here to select the Lyrtech Small Form Factor
84 Software Defined Radio (SFFSDR) board.
86 config MACH_NEUROS_OSD2
87 bool "Neuros OSD2 Open Television Set Top Box"
88 depends on ARCH_DAVINCI_DM644x
90 Configure this option to specify the whether the board used
91 for development is a Neuros OSD2 Open Set Top Box.
93 config MACH_DAVINCI_DM355_EVM
95 default ARCH_DAVINCI_DM355
96 depends on ARCH_DAVINCI_DM355
98 Configure this option to specify the whether the board used
99 for development is a DM355 EVM
101 config MACH_DM355_LEOPARD
102 bool "DM355 Leopard board"
103 depends on ARCH_DAVINCI_DM355
105 Configure this option to specify the whether the board used
106 for development is a DM355 Leopard board.
108 config MACH_DAVINCI_DM6467_EVM
110 default ARCH_DAVINCI_DM646x
111 depends on ARCH_DAVINCI_DM646x
114 select MACH_DAVINCI_DM6467TEVM
116 Configure this option to specify the whether the board used
117 for development is a DM6467 EVM
119 config MACH_DAVINCI_DM6467TEVM
122 config MACH_DAVINCI_DM365_EVM
124 default ARCH_DAVINCI_DM365
125 depends on ARCH_DAVINCI_DM365
129 Configure this option to specify whether the board used
130 for development is a DM365 EVM
132 config MACH_DAVINCI_DA830_EVM
133 bool "TI DA830/OMAP-L137/AM17x Reference Platform"
134 default ARCH_DAVINCI_DA830
135 depends on ARCH_DAVINCI_DA830
140 Say Y here to select the TI DA830/OMAP-L137/AM17x Evaluation Module.
143 prompt "Select DA830/OMAP-L137/AM17x UI board peripheral"
144 depends on MACH_DAVINCI_DA830_EVM
146 The presence of UI card on the DA830/OMAP-L137/AM17x EVM is
147 detected automatically based on successful probe of the I2C
148 based GPIO expander on that board. This option selected in this
149 menu has an effect only in case of a successful UI card detection.
154 Say Y here to use the LCD as a framebuffer or simple character
160 Say Y here to use the NAND flash. Do not forget to setup
161 the switch correctly.
164 config MACH_DAVINCI_DA850_EVM
165 bool "TI DA850/OMAP-L138/AM18x Reference Platform"
166 default ARCH_DAVINCI_DA850
167 depends on ARCH_DAVINCI_DA850
169 Say Y here to select the TI DA850/OMAP-L138/AM18x Evaluation Module.
172 prompt "Select peripherals connected to expander on UI board"
173 depends on MACH_DAVINCI_DA850_EVM
175 The presence of User Interface (UI) card on the DA850/OMAP-L138/AM18x
176 EVM is detected automatically based on successful probe of the I2C
177 based GPIO expander on that card. This option selected in this
178 menu has an effect only in case of a successful UI card detection.
181 bool "No peripheral is enabled"
183 Say Y if you do not want to enable any of the peripherals connected
184 to TCA6416 expander on DA850/OMAP-L138/AM18x EVM UI card
187 bool "RMII Ethernet PHY"
189 Say Y if you want to use the RMII PHY on the DA850/OMAP-L138/AM18x
190 EVM. This PHY is found on the UI daughter card that is supplied with
192 NOTE: Please take care while choosing this option, MII PHY will
193 not be functional if RMII mode is selected.
195 config DA850_UI_SD_VIDEO_PORT
196 bool "Video Port Interface"
198 Say Y if you want to use Video Port Interface (VPIF) on the
199 DA850/OMAP-L138 EVM. The Video decoders/encoders are found on the
200 UI daughter card that is supplied with the EVM.
204 config MACH_MITYOMAPL138
205 bool "Critical Link MityDSP-L138/MityARM-1808 SoM"
206 depends on ARCH_DAVINCI_DA850
210 Say Y here to select the Critical Link MityDSP-L138/MityARM-1808
211 System on Module. Information on this SoM may be found at
212 http://www.mitydsp.com
214 config MACH_OMAPL138_HAWKBOARD
215 bool "TI AM1808 / OMAPL-138 Hawkboard platform"
216 depends on ARCH_DAVINCI_DA850
218 Say Y here to select the TI AM1808 / OMAPL-138 Hawkboard platform .
219 Information of this board may be found at
220 http://www.hawkboard.org/
223 bool "DAVINCI multiplexing support"
224 depends on ARCH_DAVINCI
227 Pin multiplexing support for DAVINCI boards. If your bootloader
228 sets the multiplexing correctly, say N. Otherwise, or if unsure,
231 config DAVINCI_MUX_DEBUG
232 bool "Multiplexing debug output"
233 depends on DAVINCI_MUX
235 Makes the multiplexing functions print out a lot of debug info.
236 This is useful if you want to find out the correct values of the
237 multiplexing registers.
239 config DAVINCI_MUX_WARNINGS
240 bool "Warn about pins the bootloader didn't set up"
241 depends on DAVINCI_MUX
243 Choose Y here to warn whenever driver initialization logic needs
244 to change the pin multiplexing setup. When there are no warnings
245 printed, it's safe to deselect DAVINCI_MUX for your product.
247 config DAVINCI_RESET_CLOCKS
248 bool "Reset unused clocks during boot"
249 depends on ARCH_DAVINCI
251 Say Y if you want to reset unused clocks during boot.
252 This option saves power, but assumes all drivers are
253 using the clock framework. Broken drivers that do not
254 yet use clock framework may not work with this option.
255 If you are booting from another operating system, you
256 probably do not want this option enabled until your
257 device drivers work properly.