davinci: mityomapl138: make file local data static
[deliverable/linux.git] / arch / arm / mach-davinci / board-mityomapl138.c
1 /*
2 * Critical Link MityOMAP-L138 SoM
3 *
4 * Copyright (C) 2010 Critical Link LLC - http://www.criticallink.com
5 *
6 * This file is licensed under the terms of the GNU General Public License
7 * version 2. This program is licensed "as is" without any warranty of
8 * any kind, whether express or implied.
9 */
10
11 #include <linux/kernel.h>
12 #include <linux/init.h>
13 #include <linux/console.h>
14 #include <linux/platform_device.h>
15 #include <linux/mtd/partitions.h>
16 #include <linux/regulator/machine.h>
17 #include <linux/i2c.h>
18 #include <linux/i2c/at24.h>
19 #include <linux/etherdevice.h>
20
21 #include <asm/mach-types.h>
22 #include <asm/mach/arch.h>
23 #include <mach/common.h>
24 #include <mach/cp_intc.h>
25 #include <mach/da8xx.h>
26 #include <mach/nand.h>
27 #include <mach/mux.h>
28
29 #define MITYOMAPL138_PHY_ID "0:03"
30
31 #define FACTORY_CONFIG_MAGIC 0x012C0138
32 #define FACTORY_CONFIG_VERSION 0x00010001
33
34 /* Data Held in On-Board I2C device */
35 struct factory_config {
36 u32 magic;
37 u32 version;
38 u8 mac[6];
39 u32 fpga_type;
40 u32 spare;
41 u32 serialnumber;
42 char partnum[32];
43 };
44
45 static struct factory_config factory_config;
46
47 static void read_factory_config(struct memory_accessor *a, void *context)
48 {
49 int ret;
50 struct davinci_soc_info *soc_info = &davinci_soc_info;
51
52 ret = a->read(a, (char *)&factory_config, 0, sizeof(factory_config));
53 if (ret != sizeof(struct factory_config)) {
54 pr_warning("MityOMAPL138: Read Factory Config Failed: %d\n",
55 ret);
56 return;
57 }
58
59 if (factory_config.magic != FACTORY_CONFIG_MAGIC) {
60 pr_warning("MityOMAPL138: Factory Config Magic Wrong (%X)\n",
61 factory_config.magic);
62 return;
63 }
64
65 if (factory_config.version != FACTORY_CONFIG_VERSION) {
66 pr_warning("MityOMAPL138: Factory Config Version Wrong (%X)\n",
67 factory_config.version);
68 return;
69 }
70
71 pr_info("MityOMAPL138: Found MAC = %pM\n", factory_config.mac);
72 pr_info("MityOMAPL138: Part Number = %s\n", factory_config.partnum);
73 if (is_valid_ether_addr(factory_config.mac))
74 memcpy(soc_info->emac_pdata->mac_addr,
75 factory_config.mac, ETH_ALEN);
76 else
77 pr_warning("MityOMAPL138: Invalid MAC found "
78 "in factory config block\n");
79 }
80
81 static struct at24_platform_data mityomapl138_fd_chip = {
82 .byte_len = 256,
83 .page_size = 8,
84 .flags = AT24_FLAG_READONLY | AT24_FLAG_IRUGO,
85 .setup = read_factory_config,
86 .context = NULL,
87 };
88
89 static struct davinci_i2c_platform_data mityomap_i2c_0_pdata = {
90 .bus_freq = 100, /* kHz */
91 .bus_delay = 0, /* usec */
92 };
93
94 /* TPS65023 voltage regulator support */
95 /* 1.2V Core */
96 static struct regulator_consumer_supply tps65023_dcdc1_consumers[] = {
97 {
98 .supply = "cvdd",
99 },
100 };
101
102 /* 1.8V */
103 static struct regulator_consumer_supply tps65023_dcdc2_consumers[] = {
104 {
105 .supply = "usb0_vdda18",
106 },
107 {
108 .supply = "usb1_vdda18",
109 },
110 {
111 .supply = "ddr_dvdd18",
112 },
113 {
114 .supply = "sata_vddr",
115 },
116 };
117
118 /* 1.2V */
119 static struct regulator_consumer_supply tps65023_dcdc3_consumers[] = {
120 {
121 .supply = "sata_vdd",
122 },
123 {
124 .supply = "usb_cvdd",
125 },
126 {
127 .supply = "pll0_vdda",
128 },
129 {
130 .supply = "pll1_vdda",
131 },
132 };
133
134 /* 1.8V Aux LDO, not used */
135 static struct regulator_consumer_supply tps65023_ldo1_consumers[] = {
136 {
137 .supply = "1.8v_aux",
138 },
139 };
140
141 /* FPGA VCC Aux (2.5 or 3.3) LDO */
142 static struct regulator_consumer_supply tps65023_ldo2_consumers[] = {
143 {
144 .supply = "vccaux",
145 },
146 };
147
148 static struct regulator_init_data tps65023_regulator_data[] = {
149 /* dcdc1 */
150 {
151 .constraints = {
152 .min_uV = 1150000,
153 .max_uV = 1350000,
154 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
155 REGULATOR_CHANGE_STATUS,
156 .boot_on = 1,
157 },
158 .num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc1_consumers),
159 .consumer_supplies = tps65023_dcdc1_consumers,
160 },
161 /* dcdc2 */
162 {
163 .constraints = {
164 .min_uV = 1800000,
165 .max_uV = 1800000,
166 .valid_ops_mask = REGULATOR_CHANGE_STATUS,
167 .boot_on = 1,
168 },
169 .num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc2_consumers),
170 .consumer_supplies = tps65023_dcdc2_consumers,
171 },
172 /* dcdc3 */
173 {
174 .constraints = {
175 .min_uV = 1200000,
176 .max_uV = 1200000,
177 .valid_ops_mask = REGULATOR_CHANGE_STATUS,
178 .boot_on = 1,
179 },
180 .num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc3_consumers),
181 .consumer_supplies = tps65023_dcdc3_consumers,
182 },
183 /* ldo1 */
184 {
185 .constraints = {
186 .min_uV = 1800000,
187 .max_uV = 1800000,
188 .valid_ops_mask = REGULATOR_CHANGE_STATUS,
189 .boot_on = 1,
190 },
191 .num_consumer_supplies = ARRAY_SIZE(tps65023_ldo1_consumers),
192 .consumer_supplies = tps65023_ldo1_consumers,
193 },
194 /* ldo2 */
195 {
196 .constraints = {
197 .min_uV = 2500000,
198 .max_uV = 3300000,
199 .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
200 REGULATOR_CHANGE_STATUS,
201 .boot_on = 1,
202 },
203 .num_consumer_supplies = ARRAY_SIZE(tps65023_ldo2_consumers),
204 .consumer_supplies = tps65023_ldo2_consumers,
205 },
206 };
207
208 static struct i2c_board_info __initdata mityomap_tps65023_info[] = {
209 {
210 I2C_BOARD_INFO("tps65023", 0x48),
211 .platform_data = &tps65023_regulator_data[0],
212 },
213 {
214 I2C_BOARD_INFO("24c02", 0x50),
215 .platform_data = &mityomapl138_fd_chip,
216 },
217 };
218
219 static int __init pmic_tps65023_init(void)
220 {
221 return i2c_register_board_info(1, mityomap_tps65023_info,
222 ARRAY_SIZE(mityomap_tps65023_info));
223 }
224
225 /*
226 * MityDSP-L138 includes a 256 MByte large-page NAND flash
227 * (128K blocks).
228 */
229 static struct mtd_partition mityomapl138_nandflash_partition[] = {
230 {
231 .name = "rootfs",
232 .offset = 0,
233 .size = SZ_128M,
234 .mask_flags = 0, /* MTD_WRITEABLE, */
235 },
236 {
237 .name = "homefs",
238 .offset = MTDPART_OFS_APPEND,
239 .size = MTDPART_SIZ_FULL,
240 .mask_flags = 0,
241 },
242 };
243
244 static struct davinci_nand_pdata mityomapl138_nandflash_data = {
245 .parts = mityomapl138_nandflash_partition,
246 .nr_parts = ARRAY_SIZE(mityomapl138_nandflash_partition),
247 .ecc_mode = NAND_ECC_HW,
248 .options = NAND_USE_FLASH_BBT | NAND_BUSWIDTH_16,
249 .ecc_bits = 1, /* 4 bit mode is not supported with 16 bit NAND */
250 };
251
252 static struct resource mityomapl138_nandflash_resource[] = {
253 {
254 .start = DA8XX_AEMIF_CS3_BASE,
255 .end = DA8XX_AEMIF_CS3_BASE + SZ_512K + 2 * SZ_1K - 1,
256 .flags = IORESOURCE_MEM,
257 },
258 {
259 .start = DA8XX_AEMIF_CTL_BASE,
260 .end = DA8XX_AEMIF_CTL_BASE + SZ_32K - 1,
261 .flags = IORESOURCE_MEM,
262 },
263 };
264
265 static struct platform_device mityomapl138_nandflash_device = {
266 .name = "davinci_nand",
267 .id = 0,
268 .dev = {
269 .platform_data = &mityomapl138_nandflash_data,
270 },
271 .num_resources = ARRAY_SIZE(mityomapl138_nandflash_resource),
272 .resource = mityomapl138_nandflash_resource,
273 };
274
275 static struct platform_device *mityomapl138_devices[] __initdata = {
276 &mityomapl138_nandflash_device,
277 };
278
279 static void __init mityomapl138_setup_nand(void)
280 {
281 platform_add_devices(mityomapl138_devices,
282 ARRAY_SIZE(mityomapl138_devices));
283 }
284
285 static struct davinci_uart_config mityomapl138_uart_config __initdata = {
286 .enabled_uarts = 0x7,
287 };
288
289 static const short mityomap_mii_pins[] = {
290 DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3,
291 DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER,
292 DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3,
293 DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK,
294 DA850_MDIO_D,
295 -1
296 };
297
298 static const short mityomap_rmii_pins[] = {
299 DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN,
300 DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1,
301 DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK,
302 DA850_MDIO_D,
303 -1
304 };
305
306 static void __init mityomapl138_config_emac(void)
307 {
308 void __iomem *cfg_chip3_base;
309 int ret;
310 u32 val;
311 struct davinci_soc_info *soc_info = &davinci_soc_info;
312
313 soc_info->emac_pdata->rmii_en = 0; /* hardcoded for now */
314
315 cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
316 val = __raw_readl(cfg_chip3_base);
317
318 if (soc_info->emac_pdata->rmii_en) {
319 val |= BIT(8);
320 ret = davinci_cfg_reg_list(mityomap_rmii_pins);
321 pr_info("RMII PHY configured\n");
322 } else {
323 val &= ~BIT(8);
324 ret = davinci_cfg_reg_list(mityomap_mii_pins);
325 pr_info("MII PHY configured\n");
326 }
327
328 if (ret) {
329 pr_warning("mii/rmii mux setup failed: %d\n", ret);
330 return;
331 }
332
333 /* configure the CFGCHIP3 register for RMII or MII */
334 __raw_writel(val, cfg_chip3_base);
335
336 soc_info->emac_pdata->phy_id = MITYOMAPL138_PHY_ID;
337
338 ret = da8xx_register_emac();
339 if (ret)
340 pr_warning("emac registration failed: %d\n", ret);
341 }
342
343 static struct davinci_pm_config da850_pm_pdata = {
344 .sleepcount = 128,
345 };
346
347 static struct platform_device da850_pm_device = {
348 .name = "pm-davinci",
349 .dev = {
350 .platform_data = &da850_pm_pdata,
351 },
352 .id = -1,
353 };
354
355 static void __init mityomapl138_init(void)
356 {
357 int ret;
358
359 /* for now, no special EDMA channels are reserved */
360 ret = da850_register_edma(NULL);
361 if (ret)
362 pr_warning("edma registration failed: %d\n", ret);
363
364 ret = da8xx_register_watchdog();
365 if (ret)
366 pr_warning("watchdog registration failed: %d\n", ret);
367
368 davinci_serial_init(&mityomapl138_uart_config);
369
370 ret = da8xx_register_i2c(0, &mityomap_i2c_0_pdata);
371 if (ret)
372 pr_warning("i2c0 registration failed: %d\n", ret);
373
374 ret = pmic_tps65023_init();
375 if (ret)
376 pr_warning("TPS65023 PMIC init failed: %d\n", ret);
377
378 mityomapl138_setup_nand();
379
380 mityomapl138_config_emac();
381
382 ret = da8xx_register_rtc();
383 if (ret)
384 pr_warning("rtc setup failed: %d\n", ret);
385
386 ret = da850_register_cpufreq("pll0_sysclk3");
387 if (ret)
388 pr_warning("cpufreq registration failed: %d\n", ret);
389
390 ret = da8xx_register_cpuidle();
391 if (ret)
392 pr_warning("cpuidle registration failed: %d\n", ret);
393
394 ret = da850_register_pm(&da850_pm_device);
395 if (ret)
396 pr_warning("da850_evm_init: suspend registration failed: %d\n",
397 ret);
398 }
399
400 #ifdef CONFIG_SERIAL_8250_CONSOLE
401 static int __init mityomapl138_console_init(void)
402 {
403 if (!machine_is_mityomapl138())
404 return 0;
405
406 return add_preferred_console("ttyS", 1, "115200");
407 }
408 console_initcall(mityomapl138_console_init);
409 #endif
410
411 static void __init mityomapl138_map_io(void)
412 {
413 da850_init();
414 }
415
416 MACHINE_START(MITYOMAPL138, "MityDSP-L138/MityARM-1808")
417 .phys_io = IO_PHYS,
418 .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc,
419 .boot_params = (DA8XX_DDR_BASE + 0x100),
420 .map_io = mityomapl138_map_io,
421 .init_irq = cp_intc_init,
422 .timer = &davinci_timer,
423 .init_machine = mityomapl138_init,
424 MACHINE_END
This page took 0.090664 seconds and 5 git commands to generate.