arch/arm/mach-imx/Kconfig

   1 menuconfig ARCH_MXC
   2         bool "Freescale i.MX family" if ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7
   3         select ARCH_HAS_OPP
   4         select ARCH_REQUIRE_GPIOLIB
   5         select ARM_CPU_SUSPEND if PM
   6         select CLKSRC_MMIO
   7         select GENERIC_IRQ_CHIP
   8         select PINCTRL
   9         select PM_OPP if PM
  10         select SOC_BUS
  11         select SRAM
  12         help
  13           Support for Freescale MXC/iMX-based family of processors
  14
  15 if ARCH_MXC
  16
  17 config MXC_TZIC
  18         bool
  19
  20 config MXC_AVIC
  21         bool
  22
  23 config MXC_DEBUG_BOARD
  24         bool "Enable MXC debug board(for 3-stack)"
  25         help
  26           The debug board is an integral part of the MXC 3-stack(PDK)
  27           platforms, it can be attached or removed from the peripheral
  28           board. On debug board, several debug devices(ethernet, UART,
  29           buttons, LEDs and JTAG) are implemented. Between the MCU and
  30           these devices, a CPLD is added as a bridge which performs
  31           data/address de-multiplexing and decode, signal level shift,
  32           interrupt control and various board functions.
  33
  34 config HAVE_EPIT
  35         bool
  36
  37 config MXC_USE_EPIT
  38         bool "Use EPIT instead of GPT"
  39         depends on HAVE_EPIT
  40         help
  41           Use EPIT as the system timer on systems that have it. Normally you
  42           don't have a reason to do so as the EPIT has the same features and
  43           uses the same clocks as the GPT. Anyway, on some systems the GPT
  44           may be in use for other purposes.
  45
  46 config ARCH_HAS_RNGA
  47         bool
  48
  49 config HAVE_IMX_ANATOP
  50         bool
  51
  52 config HAVE_IMX_GPC
  53         bool
  54
  55 config HAVE_IMX_MMDC
  56         bool
  57
  58 config HAVE_IMX_SRC
  59         def_bool y if SMP
  60         select ARCH_HAS_RESET_CONTROLLER
  61
  62 config IMX_HAVE_IOMUX_V1
  63         bool
  64
  65 config ARCH_MXC_IOMUX_V3
  66         bool
  67
  68 config ARCH_MX1
  69         bool
  70
  71 config ARCH_MX25
  72         bool
  73
  74 config MACH_MX27
  75         bool
  76
  77 config SOC_IMX1
  78         bool
  79         select ARCH_MX1
  80         select CPU_ARM920T
  81         select IMX_HAVE_IOMUX_V1
  82         select MXC_AVIC
  83
  84 config SOC_IMX21
  85         bool
  86         select CPU_ARM926T
  87         select IMX_HAVE_IOMUX_V1
  88         select MXC_AVIC
  89
  90 config SOC_IMX25
  91         bool
  92         select ARCH_MX25
  93         select ARCH_MXC_IOMUX_V3
  94         select CPU_ARM926T
  95         select MXC_AVIC
  96         select PINCTRL_IMX25
  97
  98 config SOC_IMX27
  99         bool
 100         select ARCH_HAS_OPP
 101         select CPU_ARM926T
 102         select IMX_HAVE_IOMUX_V1
 103         select MACH_MX27
 104         select MXC_AVIC
 105         select PINCTRL_IMX27
 106
 107 config SOC_IMX31
 108         bool
 109         select CPU_V6
 110         select IMX_HAVE_PLATFORM_MXC_RNGA
 111         select MXC_AVIC
 112         select SMP_ON_UP if SMP
 113
 114 config SOC_IMX35
 115         bool
 116         select ARCH_MXC_IOMUX_V3
 117         select HAVE_EPIT
 118         select MXC_AVIC
 119         select PINCTRL_IMX35
 120         select SMP_ON_UP if SMP
 121
 122 config SOC_IMX5
 123         bool
 124         select ARCH_HAS_OPP
 125         select ARCH_MXC_IOMUX_V3
 126         select MXC_TZIC
 127
 128 config  SOC_IMX51
 129         bool
 130         select HAVE_IMX_SRC
 131         select PINCTRL_IMX51
 132         select SOC_IMX5
 133
 134 if ARCH_MULTI_V4T
 135
 136 comment "MX1 platforms:"
 137 config MACH_MXLADS
 138         bool
 139
 140 config ARCH_MX1ADS
 141         bool "MX1ADS platform"
 142         select IMX_HAVE_PLATFORM_IMX_I2C
 143         select IMX_HAVE_PLATFORM_IMX_UART
 144         select MACH_MXLADS
 145         select SOC_IMX1
 146         help
 147           Say Y here if you are using Motorola MX1ADS/MXLADS boards
 148
 149 config MACH_SCB9328
 150         bool "Synertronixx scb9328"
 151         select IMX_HAVE_PLATFORM_IMX_UART
 152         select SOC_IMX1
 153         help
 154           Say Y here if you are using a Synertronixx scb9328 board
 155
 156 config MACH_APF9328
 157         bool "APF9328"
 158         select IMX_HAVE_PLATFORM_IMX_I2C
 159         select IMX_HAVE_PLATFORM_IMX_UART
 160         select SOC_IMX1
 161         help
 162           Say Yes here if you are using the Armadeus APF9328 development board
 163
 164 endif
 165
 166 if ARCH_MULTI_V5
 167
 168 comment "MX21 platforms:"
 169
 170 config MACH_MX21ADS
 171         bool "MX21ADS platform"
 172         select IMX_HAVE_PLATFORM_IMX_FB
 173         select IMX_HAVE_PLATFORM_IMX_UART
 174         select IMX_HAVE_PLATFORM_MXC_MMC
 175         select IMX_HAVE_PLATFORM_MXC_NAND
 176         select SOC_IMX21
 177         help
 178           Include support for MX21ADS platform. This includes specific
 179           configurations for the board and its peripherals.
 180
 181 comment "MX25 platforms:"
 182
 183 config MACH_MX25_3DS
 184         bool "Support MX25PDK (3DS) Platform"
 185         select IMX_HAVE_PLATFORM_FLEXCAN
 186         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 187         select IMX_HAVE_PLATFORM_IMX2_WDT
 188         select IMX_HAVE_PLATFORM_IMXDI_RTC
 189         select IMX_HAVE_PLATFORM_IMX_FB
 190         select IMX_HAVE_PLATFORM_IMX_I2C
 191         select IMX_HAVE_PLATFORM_IMX_KEYPAD
 192         select IMX_HAVE_PLATFORM_IMX_UART
 193         select IMX_HAVE_PLATFORM_MXC_EHCI
 194         select IMX_HAVE_PLATFORM_MXC_NAND
 195         select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 196         select SOC_IMX25
 197
 198 config MACH_EUKREA_CPUIMX25SD
 199         bool "Support Eukrea CPUIMX25 Platform"
 200         select IMX_HAVE_PLATFORM_FLEXCAN
 201         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 202         select IMX_HAVE_PLATFORM_IMX2_WDT
 203         select IMX_HAVE_PLATFORM_IMXDI_RTC
 204         select IMX_HAVE_PLATFORM_IMX_FB
 205         select IMX_HAVE_PLATFORM_IMX_I2C
 206         select IMX_HAVE_PLATFORM_IMX_UART
 207         select IMX_HAVE_PLATFORM_MXC_EHCI
 208         select IMX_HAVE_PLATFORM_MXC_NAND
 209         select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 210         select USB_ULPI_VIEWPORT if USB_ULPI
 211         select SOC_IMX25
 212
 213 choice
 214         prompt "Baseboard"
 215         depends on MACH_EUKREA_CPUIMX25SD
 216         default MACH_EUKREA_MBIMXSD25_BASEBOARD
 217
 218 config MACH_EUKREA_MBIMXSD25_BASEBOARD
 219         bool "Eukrea MBIMXSD development board"
 220         select IMX_HAVE_PLATFORM_GPIO_KEYS
 221         select IMX_HAVE_PLATFORM_IMX_SSI
 222         select IMX_HAVE_PLATFORM_SPI_IMX
 223         select LEDS_GPIO_REGISTER
 224         help
 225           This adds board specific devices that can be found on Eukrea's
 226           MBIMXSD evaluation board.
 227
 228 endchoice
 229
 230 config MACH_IMX25_DT
 231         bool "Support i.MX25 platforms from device tree"
 232         select SOC_IMX25
 233         help
 234           Include support for Freescale i.MX25 based platforms
 235           using the device tree for discovery
 236
 237 comment "MX27 platforms:"
 238
 239 config MACH_MX27ADS
 240         bool "MX27ADS platform"
 241         select IMX_HAVE_PLATFORM_IMX_FB
 242         select IMX_HAVE_PLATFORM_IMX_I2C
 243         select IMX_HAVE_PLATFORM_IMX_UART
 244         select IMX_HAVE_PLATFORM_MXC_MMC
 245         select IMX_HAVE_PLATFORM_MXC_NAND
 246         select IMX_HAVE_PLATFORM_MXC_W1
 247         select SOC_IMX27
 248         help
 249           Include support for MX27ADS platform. This includes specific
 250           configurations for the board and its peripherals.
 251
 252 config MACH_PCM038
 253         bool "Phytec phyCORE-i.MX27 CPU module (pcm038)"
 254         select IMX_HAVE_PLATFORM_IMX2_WDT
 255         select IMX_HAVE_PLATFORM_IMX_I2C
 256         select IMX_HAVE_PLATFORM_IMX_UART
 257         select IMX_HAVE_PLATFORM_MXC_EHCI
 258         select IMX_HAVE_PLATFORM_MXC_NAND
 259         select IMX_HAVE_PLATFORM_MXC_W1
 260         select IMX_HAVE_PLATFORM_SPI_IMX
 261         select USB_ULPI_VIEWPORT if USB_ULPI
 262         select SOC_IMX27
 263         help
 264           Include support for phyCORE-i.MX27 (aka pcm038) platform. This
 265           includes specific configurations for the module and its peripherals.
 266
 267 choice
 268         prompt "Baseboard"
 269         depends on MACH_PCM038
 270         default MACH_PCM970_BASEBOARD
 271
 272 config MACH_PCM970_BASEBOARD
 273         bool "PHYTEC PCM970 development board"
 274         select IMX_HAVE_PLATFORM_IMX_FB
 275         select IMX_HAVE_PLATFORM_MXC_MMC
 276         help
 277           This adds board specific devices that can be found on Phytec's
 278           PCM970 evaluation board.
 279
 280 endchoice
 281
 282 config MACH_CPUIMX27
 283         bool "Eukrea CPUIMX27 module"
 284         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 285         select IMX_HAVE_PLATFORM_IMX2_WDT
 286         select IMX_HAVE_PLATFORM_IMX_I2C
 287         select IMX_HAVE_PLATFORM_IMX_UART
 288         select IMX_HAVE_PLATFORM_MXC_EHCI
 289         select IMX_HAVE_PLATFORM_MXC_NAND
 290         select IMX_HAVE_PLATFORM_MXC_W1
 291         select USB_ULPI_VIEWPORT if USB_ULPI
 292         select SOC_IMX27
 293         help
 294           Include support for Eukrea CPUIMX27 platform. This includes
 295           specific configurations for the module and its peripherals.
 296
 297 config MACH_EUKREA_CPUIMX27_USESDHC2
 298         bool "CPUIMX27 integrates SDHC2 module"
 299         depends on MACH_CPUIMX27
 300         select IMX_HAVE_PLATFORM_MXC_MMC
 301         help
 302           This adds support for the internal SDHC2 used on CPUIMX27
 303           for wifi or eMMC.
 304
 305 config MACH_EUKREA_CPUIMX27_USEUART4
 306         bool "CPUIMX27 integrates UART4 module"
 307         depends on MACH_CPUIMX27
 308         help
 309           This adds support for the internal UART4 used on CPUIMX27
 310           for bluetooth.
 311
 312 choice
 313         prompt "Baseboard"
 314         depends on MACH_CPUIMX27
 315         default MACH_EUKREA_MBIMX27_BASEBOARD
 316
 317 config MACH_EUKREA_MBIMX27_BASEBOARD
 318         bool "Eukrea MBIMX27 development board"
 319         select IMX_HAVE_PLATFORM_IMX_FB
 320         select IMX_HAVE_PLATFORM_IMX_KEYPAD
 321         select IMX_HAVE_PLATFORM_IMX_SSI
 322         select IMX_HAVE_PLATFORM_IMX_UART
 323         select IMX_HAVE_PLATFORM_MXC_MMC
 324         select IMX_HAVE_PLATFORM_SPI_IMX
 325         select LEDS_GPIO_REGISTER
 326         help
 327           This adds board specific devices that can be found on Eukrea's
 328           MBIMX27 evaluation board.
 329
 330 endchoice
 331
 332 config MACH_MX27_3DS
 333         bool "MX27PDK platform"
 334         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 335         select IMX_HAVE_PLATFORM_IMX2_WDT
 336         select IMX_HAVE_PLATFORM_IMX_FB
 337         select IMX_HAVE_PLATFORM_IMX_I2C
 338         select IMX_HAVE_PLATFORM_IMX_KEYPAD
 339         select IMX_HAVE_PLATFORM_IMX_SSI
 340         select IMX_HAVE_PLATFORM_IMX_UART
 341         select IMX_HAVE_PLATFORM_MX2_CAMERA
 342         select IMX_HAVE_PLATFORM_MXC_EHCI
 343         select IMX_HAVE_PLATFORM_MXC_MMC
 344         select IMX_HAVE_PLATFORM_SPI_IMX
 345         select MXC_DEBUG_BOARD
 346         select USB_ULPI_VIEWPORT if USB_ULPI
 347         select SOC_IMX27
 348         help
 349           Include support for MX27PDK platform. This includes specific
 350           configurations for the board and its peripherals.
 351
 352 config MACH_IMX27_VISSTRIM_M10
 353         bool "Vista Silicon i.MX27 Visstrim_m10"
 354         select IMX_HAVE_PLATFORM_GPIO_KEYS
 355         select IMX_HAVE_PLATFORM_IMX_I2C
 356         select IMX_HAVE_PLATFORM_IMX_SSI
 357         select IMX_HAVE_PLATFORM_IMX_UART
 358         select IMX_HAVE_PLATFORM_MX2_CAMERA
 359         select IMX_HAVE_PLATFORM_MX2_EMMA
 360         select IMX_HAVE_PLATFORM_MXC_EHCI
 361         select IMX_HAVE_PLATFORM_MXC_MMC
 362         select LEDS_GPIO_REGISTER
 363         select SOC_IMX27
 364         help
 365           Include support for Visstrim_m10 platform and its different variants.
 366           This includes specific configurations for the board and its
 367           peripherals.
 368
 369 config MACH_IMX27LITE
 370         bool "LogicPD MX27 LITEKIT platform"
 371         select IMX_HAVE_PLATFORM_IMX_SSI
 372         select IMX_HAVE_PLATFORM_IMX_UART
 373         select SOC_IMX27
 374         help
 375           Include support for MX27 LITEKIT platform. This includes specific
 376           configurations for the board and its peripherals.
 377
 378 config MACH_PCA100
 379         bool "Phytec phyCARD-s (pca100)"
 380         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 381         select IMX_HAVE_PLATFORM_IMX2_WDT
 382         select IMX_HAVE_PLATFORM_IMX_FB
 383         select IMX_HAVE_PLATFORM_IMX_I2C
 384         select IMX_HAVE_PLATFORM_IMX_SSI
 385         select IMX_HAVE_PLATFORM_IMX_UART
 386         select IMX_HAVE_PLATFORM_MXC_EHCI
 387         select IMX_HAVE_PLATFORM_MXC_MMC
 388         select IMX_HAVE_PLATFORM_MXC_NAND
 389         select IMX_HAVE_PLATFORM_MXC_W1
 390         select IMX_HAVE_PLATFORM_SPI_IMX
 391         select USB_ULPI_VIEWPORT if USB_ULPI
 392         select SOC_IMX27
 393         help
 394           Include support for phyCARD-s (aka pca100) platform. This
 395           includes specific configurations for the module and its peripherals.
 396
 397 config MACH_MXT_TD60
 398         bool "Maxtrack i-MXT TD60"
 399         select IMX_HAVE_PLATFORM_IMX_FB
 400         select IMX_HAVE_PLATFORM_IMX_I2C
 401         select IMX_HAVE_PLATFORM_IMX_UART
 402         select IMX_HAVE_PLATFORM_MXC_MMC
 403         select IMX_HAVE_PLATFORM_MXC_NAND
 404         select SOC_IMX27
 405         help
 406           Include support for i-MXT (aka td60) platform. This
 407           includes specific configurations for the module and its peripherals.
 408
 409 config MACH_IMX27IPCAM
 410         bool "IMX27 IPCAM platform"
 411         select IMX_HAVE_PLATFORM_IMX2_WDT
 412         select IMX_HAVE_PLATFORM_IMX_UART
 413         select SOC_IMX27
 414         help
 415           Include support for IMX27 IPCAM platform. This includes specific
 416           configurations for the board and its peripherals.
 417
 418 config MACH_IMX27_DT
 419         bool "Support i.MX27 platforms from device tree"
 420         select SOC_IMX27
 421         help
 422           Include support for Freescale i.MX27 based platforms
 423           using the device tree for discovery
 424
 425 endif
 426
 427 if ARCH_MULTI_V6
 428
 429 comment "MX31 platforms:"
 430
 431 config MACH_MX31ADS
 432         bool "Support MX31ADS platforms"
 433         default y
 434         select IMX_HAVE_PLATFORM_IMX_I2C
 435         select IMX_HAVE_PLATFORM_IMX_SSI
 436         select IMX_HAVE_PLATFORM_IMX_UART
 437         select SOC_IMX31
 438         help
 439           Include support for MX31ADS platform. This includes specific
 440           configurations for the board and its peripherals.
 441
 442 config MACH_MX31ADS_WM1133_EV1
 443         bool "Support Wolfson Microelectronics 1133-EV1 module"
 444         depends on MACH_MX31ADS
 445         depends on MFD_WM8350_I2C
 446         depends on REGULATOR_WM8350 = y
 447         help
 448           Include support for the Wolfson Microelectronics 1133-EV1 PMU
 449           and audio module for the MX31ADS platform.
 450
 451 config MACH_MX31LILLY
 452         bool "Support MX31 LILLY-1131 platforms (INCO startec)"
 453         select IMX_HAVE_PLATFORM_IMX_UART
 454         select IMX_HAVE_PLATFORM_IPU_CORE
 455         select IMX_HAVE_PLATFORM_MXC_EHCI
 456         select IMX_HAVE_PLATFORM_MXC_MMC
 457         select IMX_HAVE_PLATFORM_SPI_IMX
 458         select USB_ULPI_VIEWPORT if USB_ULPI
 459         select SOC_IMX31
 460         help
 461           Include support for mx31 based LILLY1131 modules. This includes
 462           specific configurations for the board and its peripherals.
 463
 464 config MACH_MX31LITE
 465         bool "Support MX31 LITEKIT (LogicPD)"
 466         select IMX_HAVE_PLATFORM_IMX2_WDT
 467         select IMX_HAVE_PLATFORM_IMX_UART
 468         select IMX_HAVE_PLATFORM_MXC_EHCI
 469         select IMX_HAVE_PLATFORM_MXC_MMC
 470         select IMX_HAVE_PLATFORM_MXC_NAND
 471         select IMX_HAVE_PLATFORM_MXC_RTC
 472         select IMX_HAVE_PLATFORM_SPI_IMX
 473         select LEDS_GPIO_REGISTER
 474         select USB_ULPI_VIEWPORT if USB_ULPI
 475         select SOC_IMX31
 476         help
 477           Include support for MX31 LITEKIT platform. This includes specific
 478           configurations for the board and its peripherals.
 479
 480 config MACH_PCM037
 481         bool "Support Phytec pcm037 (i.MX31) platforms"
 482         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 483         select IMX_HAVE_PLATFORM_IMX2_WDT
 484         select IMX_HAVE_PLATFORM_IMX_I2C
 485         select IMX_HAVE_PLATFORM_IMX_UART
 486         select IMX_HAVE_PLATFORM_IPU_CORE
 487         select IMX_HAVE_PLATFORM_MXC_EHCI
 488         select IMX_HAVE_PLATFORM_MXC_MMC
 489         select IMX_HAVE_PLATFORM_MXC_NAND
 490         select IMX_HAVE_PLATFORM_MXC_W1
 491         select USB_ULPI_VIEWPORT if USB_ULPI
 492         select SOC_IMX31
 493         help
 494           Include support for Phytec pcm037 platform. This includes
 495           specific configurations for the board and its peripherals.
 496
 497 config MACH_PCM037_EET
 498         bool "Support pcm037 EET board extensions"
 499         depends on MACH_PCM037
 500         select IMX_HAVE_PLATFORM_GPIO_KEYS
 501         select IMX_HAVE_PLATFORM_SPI_IMX
 502         help
 503           Add support for PCM037 EET baseboard extensions. If you are using the
 504           OLED display with EET, use "video=mx3fb:CMEL-OLED" kernel
 505           command-line parameter.
 506
 507 config MACH_MX31_3DS
 508         bool "Support MX31PDK (3DS)"
 509         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 510         select IMX_HAVE_PLATFORM_IMX2_WDT
 511         select IMX_HAVE_PLATFORM_IMX_I2C
 512         select IMX_HAVE_PLATFORM_IMX_KEYPAD
 513         select IMX_HAVE_PLATFORM_IMX_SSI
 514         select IMX_HAVE_PLATFORM_IMX_UART
 515         select IMX_HAVE_PLATFORM_IPU_CORE
 516         select IMX_HAVE_PLATFORM_MXC_EHCI
 517         select IMX_HAVE_PLATFORM_MXC_MMC
 518         select IMX_HAVE_PLATFORM_MXC_NAND
 519         select IMX_HAVE_PLATFORM_SPI_IMX
 520         select MXC_DEBUG_BOARD
 521         select USB_ULPI_VIEWPORT if USB_ULPI
 522         select SOC_IMX31
 523         help
 524           Include support for MX31PDK (3DS) platform. This includes specific
 525           configurations for the board and its peripherals.
 526
 527 config MACH_MX31_3DS_MXC_NAND_USE_BBT
 528         bool "Make the MXC NAND driver use the in flash Bad Block Table"
 529         depends on MACH_MX31_3DS
 530         depends on MTD_NAND_MXC
 531         help
 532           Enable this if you want that the MXC NAND driver uses the in flash
 533           Bad Block Table to know what blocks are bad instead of scanning the
 534           entire flash looking for bad block markers.
 535
 536 config MACH_MX31MOBOARD
 537         bool "Support mx31moboard platforms (EPFL Mobots group)"
 538         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 539         select IMX_HAVE_PLATFORM_IMX2_WDT
 540         select IMX_HAVE_PLATFORM_IMX_I2C
 541         select IMX_HAVE_PLATFORM_IMX_SSI
 542         select IMX_HAVE_PLATFORM_IMX_UART
 543         select IMX_HAVE_PLATFORM_IPU_CORE
 544         select IMX_HAVE_PLATFORM_MXC_EHCI
 545         select IMX_HAVE_PLATFORM_MXC_MMC
 546         select IMX_HAVE_PLATFORM_SPI_IMX
 547         select LEDS_GPIO_REGISTER
 548         select USB_ULPI_VIEWPORT if USB_ULPI
 549         select SOC_IMX31
 550         help
 551           Include support for mx31moboard platform. This includes specific
 552           configurations for the board and its peripherals.
 553
 554 config MACH_QONG
 555         bool "Support Dave/DENX QongEVB-LITE platform"
 556         select IMX_HAVE_PLATFORM_IMX2_WDT
 557         select IMX_HAVE_PLATFORM_IMX_UART
 558         select SOC_IMX31
 559         help
 560           Include support for Dave/DENX QongEVB-LITE platform. This includes
 561           specific configurations for the board and its peripherals.
 562
 563 config MACH_ARMADILLO5X0
 564         bool "Support Atmark Armadillo-500 Development Base Board"
 565         select IMX_HAVE_PLATFORM_GPIO_KEYS
 566         select IMX_HAVE_PLATFORM_IMX_I2C
 567         select IMX_HAVE_PLATFORM_IMX_UART
 568         select IMX_HAVE_PLATFORM_IPU_CORE
 569         select IMX_HAVE_PLATFORM_MXC_EHCI
 570         select IMX_HAVE_PLATFORM_MXC_MMC
 571         select IMX_HAVE_PLATFORM_MXC_NAND
 572         select USB_ULPI_VIEWPORT if USB_ULPI
 573         select SOC_IMX31
 574         help
 575           Include support for Atmark Armadillo-500 platform. This includes
 576           specific configurations for the board and its peripherals.
 577
 578 config MACH_KZM_ARM11_01
 579         bool "Support KZM-ARM11-01(Kyoto Microcomputer)"
 580         select IMX_HAVE_PLATFORM_IMX_UART
 581         select SOC_IMX31
 582         help
 583           Include support for KZM-ARM11-01. This includes specific
 584           configurations for the board and its peripherals.
 585
 586 config MACH_BUG
 587         bool "Support Buglabs BUGBase platform"
 588         default y
 589         select IMX_HAVE_PLATFORM_IMX_UART
 590         select SOC_IMX31
 591         help
 592           Include support for BUGBase 1.3 platform. This includes specific
 593           configurations for the board and its peripherals.
 594
 595 config MACH_IMX31_DT
 596         bool "Support i.MX31 platforms from device tree"
 597         select SOC_IMX31
 598         help
 599           Include support for Freescale i.MX31 based platforms
 600           using the device tree for discovery.
 601
 602 comment "MX35 platforms:"
 603
 604 config MACH_IMX35_DT
 605         bool "Support i.MX35 platforms from device tree"
 606         select SOC_IMX35
 607         help
 608           Include support for Freescale i.MX35 based platforms
 609           using the device tree for discovery.
 610
 611 config MACH_PCM043
 612         bool "Support Phytec pcm043 (i.MX35) platforms"
 613         select IMX_HAVE_PLATFORM_FLEXCAN
 614         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 615         select IMX_HAVE_PLATFORM_IMX2_WDT
 616         select IMX_HAVE_PLATFORM_IMX_I2C
 617         select IMX_HAVE_PLATFORM_IMX_SSI
 618         select IMX_HAVE_PLATFORM_IMX_UART
 619         select IMX_HAVE_PLATFORM_IPU_CORE
 620         select IMX_HAVE_PLATFORM_MXC_EHCI
 621         select IMX_HAVE_PLATFORM_MXC_NAND
 622         select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 623         select USB_ULPI_VIEWPORT if USB_ULPI
 624         select SOC_IMX35
 625         help
 626           Include support for Phytec pcm043 platform. This includes
 627           specific configurations for the board and its peripherals.
 628
 629 config MACH_MX35_3DS
 630         bool "Support MX35PDK platform"
 631         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 632         select IMX_HAVE_PLATFORM_IMX2_WDT
 633         select IMX_HAVE_PLATFORM_IMX_FB
 634         select IMX_HAVE_PLATFORM_IMX_I2C
 635         select IMX_HAVE_PLATFORM_IMX_UART
 636         select IMX_HAVE_PLATFORM_IPU_CORE
 637         select IMX_HAVE_PLATFORM_MXC_EHCI
 638         select IMX_HAVE_PLATFORM_MXC_NAND
 639         select IMX_HAVE_PLATFORM_MXC_RTC
 640         select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 641         select MXC_DEBUG_BOARD
 642         select SOC_IMX35
 643         help
 644           Include support for MX35PDK platform. This includes specific
 645           configurations for the board and its peripherals.
 646
 647 config MACH_EUKREA_CPUIMX35SD
 648         bool "Support Eukrea CPUIMX35 Platform"
 649         select IMX_HAVE_PLATFORM_FLEXCAN
 650         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 651         select IMX_HAVE_PLATFORM_IMX2_WDT
 652         select IMX_HAVE_PLATFORM_IMX_I2C
 653         select IMX_HAVE_PLATFORM_IMX_UART
 654         select IMX_HAVE_PLATFORM_MXC_EHCI
 655         select IMX_HAVE_PLATFORM_MXC_NAND
 656         select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 657         select USB_ULPI_VIEWPORT if USB_ULPI
 658         select SOC_IMX35
 659         help
 660           Include support for Eukrea CPUIMX35 platform. This includes
 661           specific configurations for the board and its peripherals.
 662
 663 choice
 664         prompt "Baseboard"
 665         depends on MACH_EUKREA_CPUIMX35SD
 666         default MACH_EUKREA_MBIMXSD35_BASEBOARD
 667
 668 config MACH_EUKREA_MBIMXSD35_BASEBOARD
 669         bool "Eukrea MBIMXSD development board"
 670         select IMX_HAVE_PLATFORM_GPIO_KEYS
 671         select IMX_HAVE_PLATFORM_IMX_SSI
 672         select IMX_HAVE_PLATFORM_IPU_CORE
 673         select IMX_HAVE_PLATFORM_SPI_IMX
 674         select LEDS_GPIO_REGISTER
 675         help
 676           This adds board specific devices that can be found on Eukrea's
 677           MBIMXSD evaluation board.
 678
 679 endchoice
 680
 681 config MACH_VPR200
 682         bool "Support VPR200 platform"
 683         select IMX_HAVE_PLATFORM_FSL_USB2_UDC
 684         select IMX_HAVE_PLATFORM_GPIO_KEYS
 685         select IMX_HAVE_PLATFORM_IMX2_WDT
 686         select IMX_HAVE_PLATFORM_IMX_I2C
 687         select IMX_HAVE_PLATFORM_IMX_UART
 688         select IMX_HAVE_PLATFORM_IPU_CORE
 689         select IMX_HAVE_PLATFORM_MXC_EHCI
 690         select IMX_HAVE_PLATFORM_MXC_NAND
 691         select IMX_HAVE_PLATFORM_SDHCI_ESDHC_IMX
 692         select SOC_IMX35
 693         help
 694           Include support for VPR200 platform. This includes specific
 695           configurations for the board and its peripherals.
 696
 697 endif
 698
 699 if ARCH_MULTI_V7
 700
 701 comment "Device tree only"
 702
 703 config  SOC_IMX50
 704         bool "i.MX50 support"
 705         select HAVE_IMX_SRC
 706         select PINCTRL_IMX50
 707         select SOC_IMX5
 708
 709         help
 710           This enables support for Freescale i.MX50 processor.
 711
 712 config MACH_IMX51_DT
 713         bool "i.MX51 support"
 714         select SOC_IMX51
 715         help
 716           This enables support for Freescale i.MX51 processor
 717
 718 config  SOC_IMX53
 719         bool "i.MX53 support"
 720         select HAVE_IMX_SRC
 721         select PINCTRL_IMX53
 722         select SOC_IMX5
 723
 724         help
 725           This enables support for Freescale i.MX53 processor.
 726
 727 config SOC_IMX6
 728         bool
 729         select ARM_ERRATA_754322
 730         select ARM_ERRATA_775420
 731         select ARM_GIC
 732         select HAVE_IMX_ANATOP
 733         select HAVE_IMX_GPC
 734         select HAVE_IMX_MMDC
 735         select HAVE_IMX_SRC
 736         select MFD_SYSCON
 737         select PL310_ERRATA_588369 if CACHE_L2X0
 738         select PL310_ERRATA_727915 if CACHE_L2X0
 739         select PL310_ERRATA_769419 if CACHE_L2X0
 740
 741 config SOC_IMX6Q
 742         bool "i.MX6 Quad/DualLite support"
 743         select ARM_ERRATA_764369 if SMP
 744         select HAVE_ARM_SCU if SMP
 745         select HAVE_ARM_TWD if SMP
 746         select PCI_DOMAINS if PCI
 747         select PINCTRL_IMX6Q
 748         select SOC_IMX6
 749
 750         help
 751           This enables support for Freescale i.MX6 Quad processor.
 752
 753 config SOC_IMX6SL
 754         bool "i.MX6 SoloLite support"
 755         select PINCTRL_IMX6SL
 756         select SOC_IMX6
 757
 758         help
 759           This enables support for Freescale i.MX6 SoloLite processor.
 760
 761 config SOC_IMX6SX
 762         bool "i.MX6 SoloX support"
 763         select PINCTRL_IMX6SX
 764         select SOC_IMX6
 765
 766         help
 767           This enables support for Freescale i.MX6 SoloX processor.
 768
 769 config SOC_VF610
 770         bool "Vybrid Family VF610 support"
 771         select ARM_GIC
 772         select PINCTRL_VF610
 773         select VF_PIT_TIMER
 774         select PL310_ERRATA_588369 if CACHE_L2X0
 775         select PL310_ERRATA_727915 if CACHE_L2X0
 776         select PL310_ERRATA_769419 if CACHE_L2X0
 777
 778         help
 779           This enable support for Freescale Vybrid VF610 processor.
 780
 781 endif
 782
 783 source "arch/arm/mach-imx/devices/Kconfig"
 784
 785 endif