arch/arm/mach-omap2/board-3430sdp.c

   1 /*
   2  * linux/arch/arm/mach-omap2/board-3430sdp.c
   3  *
   4  * Copyright (C) 2007 Texas Instruments
   5  *
   6  * Modified from mach-omap2/board-generic.c
   7  *
   8  * Initial code: Syed Mohammed Khasim
   9  *
  10  * This program is free software; you can redistribute it and/or modify
  11  * it under the terms of the GNU General Public License version 2 as
  12  * published by the Free Software Foundation.
  13  */
  14
  15 #include <linux/kernel.h>
  16 #include <linux/init.h>
  17 #include <linux/platform_device.h>
  18 #include <linux/delay.h>
  19 #include <linux/input.h>
  20 #include <linux/input/matrix_keypad.h>
  21 #include <linux/spi/spi.h>
  22 #include <linux/i2c/twl.h>
  23 #include <linux/regulator/machine.h>
  24 #include <linux/io.h>
  25 #include <linux/gpio.h>
  26 #include <linux/mmc/host.h>
  27 #include <linux/platform_data/spi-omap2-mcspi.h>
  28 #include <linux/platform_data/omap-twl4030.h>
  29 #include <linux/usb/phy.h>
  30
  31 #include <asm/mach-types.h>
  32 #include <asm/mach/arch.h>
  33 #include <asm/mach/map.h>
  34
  35 #include "common.h"
  36 #include <linux/omap-dma.h>
  37 #include <video/omapdss.h>
  38 #include <video/omap-panel-data.h>
  39
  40 #include "gpmc.h"
  41 #include "gpmc-smc91x.h"
  42
  43 #include "soc.h"
  44 #include "board-flash.h"
  45 #include "mux.h"
  46 #include "sdram-qimonda-hyb18m512160af-6.h"
  47 #include "hsmmc.h"
  48 #include "pm.h"
  49 #include "control.h"
  50 #include "common-board-devices.h"
  51
  52 #define CONFIG_DISABLE_HFCLK 1
  53
  54 #define SDP3430_TS_GPIO_IRQ_SDPV1       3
  55 #define SDP3430_TS_GPIO_IRQ_SDPV2       2
  56
  57 #define ENABLE_VAUX3_DEDICATED  0x03
  58 #define ENABLE_VAUX3_DEV_GRP    0x20
  59
  60 #define TWL4030_MSECURE_GPIO 22
  61
  62 static uint32_t board_keymap[] = {
  63         KEY(0, 0, KEY_LEFT),
  64         KEY(0, 1, KEY_RIGHT),
  65         KEY(0, 2, KEY_A),
  66         KEY(0, 3, KEY_B),
  67         KEY(0, 4, KEY_C),
  68         KEY(1, 0, KEY_DOWN),
  69         KEY(1, 1, KEY_UP),
  70         KEY(1, 2, KEY_E),
  71         KEY(1, 3, KEY_F),
  72         KEY(1, 4, KEY_G),
  73         KEY(2, 0, KEY_ENTER),
  74         KEY(2, 1, KEY_I),
  75         KEY(2, 2, KEY_J),
  76         KEY(2, 3, KEY_K),
  77         KEY(2, 4, KEY_3),
  78         KEY(3, 0, KEY_M),
  79         KEY(3, 1, KEY_N),
  80         KEY(3, 2, KEY_O),
  81         KEY(3, 3, KEY_P),
  82         KEY(3, 4, KEY_Q),
  83         KEY(4, 0, KEY_R),
  84         KEY(4, 1, KEY_4),
  85         KEY(4, 2, KEY_T),
  86         KEY(4, 3, KEY_U),
  87         KEY(4, 4, KEY_D),
  88         KEY(5, 0, KEY_V),
  89         KEY(5, 1, KEY_W),
  90         KEY(5, 2, KEY_L),
  91         KEY(5, 3, KEY_S),
  92         KEY(5, 4, KEY_H),
  93         0
  94 };
  95
  96 static struct matrix_keymap_data board_map_data = {
  97         .keymap                 = board_keymap,
  98         .keymap_size            = ARRAY_SIZE(board_keymap),
  99 };
 100
 101 static struct twl4030_keypad_data sdp3430_kp_data = {
 102         .keymap_data    = &board_map_data,
 103         .rows           = 5,
 104         .cols           = 6,
 105         .rep            = 1,
 106 };
 107
 108 #define SDP3430_LCD_PANEL_BACKLIGHT_GPIO        8
 109 #define SDP3430_LCD_PANEL_ENABLE_GPIO           5
 110
 111 static void __init sdp3430_display_init(void)
 112 {
 113         int r;
 114
 115         /*
 116          * the backlight GPIO doesn't directly go to the panel, it enables
 117          * an internal circuit on 3430sdp to create the signal V_BKL_28V,
 118          * this is connected to LED+ pin of the sharp panel. This GPIO
 119          * is left enabled in the board file, and not passed to the panel
 120          * as platform_data.
 121          */
 122         r = gpio_request_one(SDP3430_LCD_PANEL_BACKLIGHT_GPIO,
 123                                 GPIOF_OUT_INIT_HIGH, "LCD Backlight");
 124         if (r)
 125                 pr_err("failed to get LCD Backlight GPIO\n");
 126
 127 }
 128
 129 static struct panel_sharp_ls037v7dw01_platform_data sdp3430_lcd_pdata = {
 130         .name                   = "lcd",
 131         .source                 = "dpi.0",
 132
 133         .data_lines             = 16,
 134
 135         .resb_gpio              = SDP3430_LCD_PANEL_ENABLE_GPIO,
 136         .ini_gpio               = -1,
 137         .mo_gpio                = -1,
 138         .lr_gpio                = -1,
 139         .ud_gpio                = -1,
 140 };
 141
 142 static struct platform_device sdp3430_lcd_device = {
 143         .name                   = "panel-sharp-ls037v7dw01",
 144         .id                     = 0,
 145         .dev.platform_data      = &sdp3430_lcd_pdata,
 146 };
 147
 148 static struct connector_dvi_platform_data sdp3430_dvi_connector_pdata = {
 149         .name                   = "dvi",
 150         .source                 = "tfp410.0",
 151         .i2c_bus_num            = -1,
 152 };
 153
 154 static struct platform_device sdp3430_dvi_connector_device = {
 155         .name                   = "connector-dvi",
 156         .id                     = 0,
 157         .dev.platform_data      = &sdp3430_dvi_connector_pdata,
 158 };
 159
 160 static struct encoder_tfp410_platform_data sdp3430_tfp410_pdata = {
 161         .name                   = "tfp410.0",
 162         .source                 = "dpi.0",
 163         .data_lines             = 24,
 164         .power_down_gpio        = -1,
 165 };
 166
 167 static struct platform_device sdp3430_tfp410_device = {
 168         .name                   = "tfp410",
 169         .id                     = 0,
 170         .dev.platform_data      = &sdp3430_tfp410_pdata,
 171 };
 172
 173 static struct connector_atv_platform_data sdp3430_tv_pdata = {
 174         .name = "tv",
 175         .source = "venc.0",
 176         .connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
 177         .invert_polarity = false,
 178 };
 179
 180 static struct platform_device sdp3430_tv_connector_device = {
 181         .name                   = "connector-analog-tv",
 182         .id                     = 0,
 183         .dev.platform_data      = &sdp3430_tv_pdata,
 184 };
 185
 186 static struct omap_dss_board_info sdp3430_dss_data = {
 187         .default_display_name = "lcd",
 188 };
 189
 190 static struct omap2_hsmmc_info mmc[] = {
 191         {
 192                 .mmc            = 1,
 193                 /* 8 bits (default) requires S6.3 == ON,
 194                  * so the SIM card isn't used; else 4 bits.
 195                  */
 196                 .caps           = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 197                 .gpio_wp        = 4,
 198                 .deferred       = true,
 199         },
 200         {
 201                 .mmc            = 2,
 202                 .caps           = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
 203                 .gpio_wp        = 7,
 204                 .deferred       = true,
 205         },
 206         {}      /* Terminator */
 207 };
 208
 209 static struct omap_tw4030_pdata omap_twl4030_audio_data = {
 210         .voice_connected = true,
 211         .custom_routing = true,
 212
 213         .has_hs         = OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
 214         .has_hf         = OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
 215
 216         .has_mainmic    = true,
 217         .has_submic     = true,
 218         .has_hsmic      = true,
 219         .has_linein     = OMAP_TWL4030_LEFT | OMAP_TWL4030_RIGHT,
 220 };
 221
 222 static int sdp3430_twl_gpio_setup(struct device *dev,
 223                 unsigned gpio, unsigned ngpio)
 224 {
 225         /* gpio + 0 is "mmc0_cd" (input/IRQ),
 226          * gpio + 1 is "mmc1_cd" (input/IRQ)
 227          */
 228         mmc[0].gpio_cd = gpio + 0;
 229         mmc[1].gpio_cd = gpio + 1;
 230         omap_hsmmc_late_init(mmc);
 231
 232         /* gpio + 7 is "sub_lcd_en_bkl" (output/PWM1) */
 233         gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "sub_lcd_en_bkl");
 234
 235         /* gpio + 15 is "sub_lcd_nRST" (output) */
 236         gpio_request_one(gpio + 15, GPIOF_OUT_INIT_LOW, "sub_lcd_nRST");
 237
 238         omap_twl4030_audio_data.jack_detect = gpio + 2;
 239         omap_twl4030_audio_init("SDP3430", &omap_twl4030_audio_data);
 240
 241         return 0;
 242 }
 243
 244 static struct twl4030_gpio_platform_data sdp3430_gpio_data = {
 245         .pulldowns      = BIT(2) | BIT(6) | BIT(8) | BIT(13)
 246                                 | BIT(16) | BIT(17),
 247         .setup          = sdp3430_twl_gpio_setup,
 248 };
 249
 250 /* regulator consumer mappings */
 251
 252 /* ads7846 on SPI */
 253 static struct regulator_consumer_supply sdp3430_vaux3_supplies[] = {
 254         REGULATOR_SUPPLY("vcc", "spi1.0"),
 255 };
 256
 257 static struct regulator_consumer_supply sdp3430_vmmc1_supplies[] = {
 258         REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
 259 };
 260
 261 static struct regulator_consumer_supply sdp3430_vsim_supplies[] = {
 262         REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
 263 };
 264
 265 static struct regulator_consumer_supply sdp3430_vmmc2_supplies[] = {
 266         REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
 267 };
 268
 269 /*
 270  * Apply all the fixed voltages since most versions of U-Boot
 271  * don't bother with that initialization.
 272  */
 273
 274 /* VAUX1 for mainboard (irda and sub-lcd) */
 275 static struct regulator_init_data sdp3430_vaux1 = {
 276         .constraints = {
 277                 .min_uV                 = 2800000,
 278                 .max_uV                 = 2800000,
 279                 .apply_uV               = true,
 280                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 281                                         | REGULATOR_MODE_STANDBY,
 282                 .valid_ops_mask         = REGULATOR_CHANGE_MODE
 283                                         | REGULATOR_CHANGE_STATUS,
 284         },
 285 };
 286
 287 /* VAUX2 for camera module */
 288 static struct regulator_init_data sdp3430_vaux2 = {
 289         .constraints = {
 290                 .min_uV                 = 2800000,
 291                 .max_uV                 = 2800000,
 292                 .apply_uV               = true,
 293                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 294                                         | REGULATOR_MODE_STANDBY,
 295                 .valid_ops_mask         = REGULATOR_CHANGE_MODE
 296                                         | REGULATOR_CHANGE_STATUS,
 297         },
 298 };
 299
 300 /* VAUX3 for LCD board */
 301 static struct regulator_init_data sdp3430_vaux3 = {
 302         .constraints = {
 303                 .min_uV                 = 2800000,
 304                 .max_uV                 = 2800000,
 305                 .apply_uV               = true,
 306                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 307                                         | REGULATOR_MODE_STANDBY,
 308                 .valid_ops_mask         = REGULATOR_CHANGE_MODE
 309                                         | REGULATOR_CHANGE_STATUS,
 310         },
 311         .num_consumer_supplies          = ARRAY_SIZE(sdp3430_vaux3_supplies),
 312         .consumer_supplies              = sdp3430_vaux3_supplies,
 313 };
 314
 315 /* VAUX4 for OMAP VDD_CSI2 (camera) */
 316 static struct regulator_init_data sdp3430_vaux4 = {
 317         .constraints = {
 318                 .min_uV                 = 1800000,
 319                 .max_uV                 = 1800000,
 320                 .apply_uV               = true,
 321                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 322                                         | REGULATOR_MODE_STANDBY,
 323                 .valid_ops_mask         = REGULATOR_CHANGE_MODE
 324                                         | REGULATOR_CHANGE_STATUS,
 325         },
 326 };
 327
 328 /* VMMC1 for OMAP VDD_MMC1 (i/o) and MMC1 card */
 329 static struct regulator_init_data sdp3430_vmmc1 = {
 330         .constraints = {
 331                 .min_uV                 = 1850000,
 332                 .max_uV                 = 3150000,
 333                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 334                                         | REGULATOR_MODE_STANDBY,
 335                 .valid_ops_mask         = REGULATOR_CHANGE_VOLTAGE
 336                                         | REGULATOR_CHANGE_MODE
 337                                         | REGULATOR_CHANGE_STATUS,
 338         },
 339         .num_consumer_supplies  = ARRAY_SIZE(sdp3430_vmmc1_supplies),
 340         .consumer_supplies      = sdp3430_vmmc1_supplies,
 341 };
 342
 343 /* VMMC2 for MMC2 card */
 344 static struct regulator_init_data sdp3430_vmmc2 = {
 345         .constraints = {
 346                 .min_uV                 = 1850000,
 347                 .max_uV                 = 1850000,
 348                 .apply_uV               = true,
 349                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 350                                         | REGULATOR_MODE_STANDBY,
 351                 .valid_ops_mask         = REGULATOR_CHANGE_MODE
 352                                         | REGULATOR_CHANGE_STATUS,
 353         },
 354         .num_consumer_supplies  = ARRAY_SIZE(sdp3430_vmmc2_supplies),
 355         .consumer_supplies      = sdp3430_vmmc2_supplies,
 356 };
 357
 358 /* VSIM for OMAP VDD_MMC1A (i/o for DAT4..DAT7) */
 359 static struct regulator_init_data sdp3430_vsim = {
 360         .constraints = {
 361                 .min_uV                 = 1800000,
 362                 .max_uV                 = 3000000,
 363                 .valid_modes_mask       = REGULATOR_MODE_NORMAL
 364                                         | REGULATOR_MODE_STANDBY,
 365                 .valid_ops_mask         = REGULATOR_CHANGE_VOLTAGE
 366                                         | REGULATOR_CHANGE_MODE
 367                                         | REGULATOR_CHANGE_STATUS,
 368         },
 369         .num_consumer_supplies  = ARRAY_SIZE(sdp3430_vsim_supplies),
 370         .consumer_supplies      = sdp3430_vsim_supplies,
 371 };
 372
 373 static struct twl4030_platform_data sdp3430_twldata = {
 374         /* platform_data for children goes here */
 375         .gpio           = &sdp3430_gpio_data,
 376         .keypad         = &sdp3430_kp_data,
 377
 378         .vaux1          = &sdp3430_vaux1,
 379         .vaux2          = &sdp3430_vaux2,
 380         .vaux3          = &sdp3430_vaux3,
 381         .vaux4          = &sdp3430_vaux4,
 382         .vmmc1          = &sdp3430_vmmc1,
 383         .vmmc2          = &sdp3430_vmmc2,
 384         .vsim           = &sdp3430_vsim,
 385 };
 386
 387 static int __init omap3430_i2c_init(void)
 388 {
 389         /* i2c1 for PMIC only */
 390         omap3_pmic_get_config(&sdp3430_twldata,
 391                         TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_BCI |
 392                         TWL_COMMON_PDATA_MADC | TWL_COMMON_PDATA_AUDIO,
 393                         TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
 394         sdp3430_twldata.vdac->constraints.apply_uV = true;
 395         sdp3430_twldata.vpll2->constraints.apply_uV = true;
 396         sdp3430_twldata.vpll2->constraints.name = "VDVI";
 397
 398         sdp3430_twldata.audio->codec->hs_extmute = 1;
 399         sdp3430_twldata.audio->codec->hs_extmute_gpio = -EINVAL;
 400
 401         omap3_pmic_init("twl4030", &sdp3430_twldata);
 402
 403         /* i2c2 on camera connector (for sensor control) and optional isp1301 */
 404         omap_register_i2c_bus(2, 400, NULL, 0);
 405         /* i2c3 on display connector (for DVI, tfp410) */
 406         omap_register_i2c_bus(3, 400, NULL, 0);
 407         return 0;
 408 }
 409
 410 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 411
 412 static struct omap_smc91x_platform_data board_smc91x_data = {
 413         .cs             = 3,
 414         .flags          = GPMC_MUX_ADD_DATA | GPMC_TIMINGS_SMC91C96 |
 415                                 IORESOURCE_IRQ_LOWLEVEL,
 416 };
 417
 418 static void __init board_smc91x_init(void)
 419 {
 420         if (omap_rev() > OMAP3430_REV_ES1_0)
 421                 board_smc91x_data.gpio_irq = 6;
 422         else
 423                 board_smc91x_data.gpio_irq = 29;
 424
 425         gpmc_smc91x_init(&board_smc91x_data);
 426 }
 427
 428 #else
 429
 430 static inline void board_smc91x_init(void)
 431 {
 432 }
 433
 434 #endif
 435
 436 static void enable_board_wakeup_source(void)
 437 {
 438         /* T2 interrupt line (keypad) */
 439         omap_mux_init_signal("sys_nirq",
 440                 OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
 441 }
 442
 443 static struct usbhs_phy_data phy_data[] __initdata = {
 444         {
 445                 .port = 1,
 446                 .reset_gpio = 57,
 447                 .vcc_gpio = -EINVAL,
 448         },
 449         {
 450                 .port = 2,
 451                 .reset_gpio = 61,
 452                 .vcc_gpio = -EINVAL,
 453         },
 454 };
 455
 456 static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
 457
 458         .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
 459         .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
 460 };
 461
 462 #ifdef CONFIG_OMAP_MUX
 463 static struct omap_board_mux board_mux[] __initdata = {
 464         { .reg_offset = OMAP_MUX_TERMINATOR },
 465 };
 466 #else
 467 #define board_mux       NULL
 468 #endif
 469
 470 /*
 471  * SDP3430 V2 Board CS organization
 472  * Different from SDP3430 V1. Now 4 switches used to specify CS
 473  *
 474  * See also the Switch S8 settings in the comments.
 475  */
 476 static char chip_sel_3430[][GPMC_CS_NUM] = {
 477         {PDC_NOR, PDC_NAND, PDC_ONENAND, DBG_MPDB, 0, 0, 0, 0}, /* S8:1111 */
 478         {PDC_ONENAND, PDC_NAND, PDC_NOR, DBG_MPDB, 0, 0, 0, 0}, /* S8:1110 */
 479         {PDC_NAND, PDC_ONENAND, PDC_NOR, DBG_MPDB, 0, 0, 0, 0}, /* S8:1101 */
 480 };
 481
 482 static struct mtd_partition sdp_nor_partitions[] = {
 483         /* bootloader (U-Boot, etc) in first sector */
 484         {
 485                 .name           = "Bootloader-NOR",
 486                 .offset         = 0,
 487                 .size           = SZ_256K,
 488                 .mask_flags     = MTD_WRITEABLE, /* force read-only */
 489         },
 490         /* bootloader params in the next sector */
 491         {
 492                 .name           = "Params-NOR",
 493                 .offset         = MTDPART_OFS_APPEND,
 494                 .size           = SZ_256K,
 495                 .mask_flags     = 0,
 496         },
 497         /* kernel */
 498         {
 499                 .name           = "Kernel-NOR",
 500                 .offset         = MTDPART_OFS_APPEND,
 501                 .size           = SZ_2M,
 502                 .mask_flags     = 0
 503         },
 504         /* file system */
 505         {
 506                 .name           = "Filesystem-NOR",
 507                 .offset         = MTDPART_OFS_APPEND,
 508                 .size           = MTDPART_SIZ_FULL,
 509                 .mask_flags     = 0
 510         }
 511 };
 512
 513 static struct mtd_partition sdp_onenand_partitions[] = {
 514         {
 515                 .name           = "X-Loader-OneNAND",
 516                 .offset         = 0,
 517                 .size           = 4 * (64 * 2048),
 518                 .mask_flags     = MTD_WRITEABLE  /* force read-only */
 519         },
 520         {
 521                 .name           = "U-Boot-OneNAND",
 522                 .offset         = MTDPART_OFS_APPEND,
 523                 .size           = 2 * (64 * 2048),
 524                 .mask_flags     = MTD_WRITEABLE  /* force read-only */
 525         },
 526         {
 527                 .name           = "U-Boot Environment-OneNAND",
 528                 .offset         = MTDPART_OFS_APPEND,
 529                 .size           = 1 * (64 * 2048),
 530         },
 531         {
 532                 .name           = "Kernel-OneNAND",
 533                 .offset         = MTDPART_OFS_APPEND,
 534                 .size           = 16 * (64 * 2048),
 535         },
 536         {
 537                 .name           = "File System-OneNAND",
 538                 .offset         = MTDPART_OFS_APPEND,
 539                 .size           = MTDPART_SIZ_FULL,
 540         },
 541 };
 542
 543 static struct mtd_partition sdp_nand_partitions[] = {
 544         /* All the partition sizes are listed in terms of NAND block size */
 545         {
 546                 .name           = "X-Loader-NAND",
 547                 .offset         = 0,
 548                 .size           = 4 * (64 * 2048),
 549                 .mask_flags     = MTD_WRITEABLE,        /* force read-only */
 550         },
 551         {
 552                 .name           = "U-Boot-NAND",
 553                 .offset         = MTDPART_OFS_APPEND,   /* Offset = 0x80000 */
 554                 .size           = 10 * (64 * 2048),
 555                 .mask_flags     = MTD_WRITEABLE,        /* force read-only */
 556         },
 557         {
 558                 .name           = "Boot Env-NAND",
 559
 560                 .offset         = MTDPART_OFS_APPEND,   /* Offset = 0x1c0000 */
 561                 .size           = 6 * (64 * 2048),
 562         },
 563         {
 564                 .name           = "Kernel-NAND",
 565                 .offset         = MTDPART_OFS_APPEND,   /* Offset = 0x280000 */
 566                 .size           = 40 * (64 * 2048),
 567         },
 568         {
 569                 .name           = "File System - NAND",
 570                 .size           = MTDPART_SIZ_FULL,
 571                 .offset         = MTDPART_OFS_APPEND,   /* Offset = 0x780000 */
 572         },
 573 };
 574
 575 static struct flash_partitions sdp_flash_partitions[] = {
 576         {
 577                 .parts = sdp_nor_partitions,
 578                 .nr_parts = ARRAY_SIZE(sdp_nor_partitions),
 579         },
 580         {
 581                 .parts = sdp_onenand_partitions,
 582                 .nr_parts = ARRAY_SIZE(sdp_onenand_partitions),
 583         },
 584         {
 585                 .parts = sdp_nand_partitions,
 586                 .nr_parts = ARRAY_SIZE(sdp_nand_partitions),
 587         },
 588 };
 589
 590 static void __init omap_3430sdp_init(void)
 591 {
 592         int gpio_pendown;
 593
 594         omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
 595         omap_hsmmc_init(mmc);
 596         omap3430_i2c_init();
 597         omap_display_init(&sdp3430_dss_data);
 598         platform_device_register(&sdp3430_lcd_device);
 599         platform_device_register(&sdp3430_tfp410_device);
 600         platform_device_register(&sdp3430_dvi_connector_device);
 601         platform_device_register(&sdp3430_tv_connector_device);
 602
 603         if (omap_rev() > OMAP3430_REV_ES1_0)
 604                 gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV2;
 605         else
 606                 gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV1;
 607         omap_ads7846_init(1, gpio_pendown, 310, NULL);
 608         omap_serial_init();
 609         omap_sdrc_init(hyb18m512160af6_sdrc_params, NULL);
 610         usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
 611         usb_musb_init(NULL);
 612         board_smc91x_init();
 613         board_flash_init(sdp_flash_partitions, chip_sel_3430, 0);
 614         sdp3430_display_init();
 615         enable_board_wakeup_source();
 616
 617         usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
 618         usbhs_init(&usbhs_bdata);
 619 }
 620
 621 MACHINE_START(OMAP_3430SDP, "OMAP3430 3430SDP board")
 622         /* Maintainer: Syed Khasim - Texas Instruments Inc */
 623         .atag_offset    = 0x100,
 624         .reserve        = omap_reserve,
 625         .map_io         = omap3_map_io,
 626         .init_early     = omap3430_init_early,
 627         .init_irq       = omap3_init_irq,
 628         .handle_irq     = omap3_intc_handle_irq,
 629         .init_machine   = omap_3430sdp_init,
 630         .init_late      = omap3430_init_late,
 631         .init_time      = omap3_sync32k_timer_init,
 632         .restart        = omap3xxx_restart,
 633 MACHINE_END