arch/arm/mach-omap2/board-n8x0.c

   1 /*
   2  * linux/arch/arm/mach-omap2/board-n8x0.c
   3  *
   4  * Copyright (C) 2005-2009 Nokia Corporation
   5  * Author: Juha Yrjola <juha.yrjola@nokia.com>
   6  *
   7  * Modified from mach-omap2/board-generic.c
   8  *
   9  * This program is free software; you can redistribute it and/or modify
  10  * it under the terms of the GNU General Public License version 2 as
  11  * published by the Free Software Foundation.
  12  */
  13
  14 #include <linux/clk.h>
  15 #include <linux/delay.h>
  16 #include <linux/gpio.h>
  17 #include <linux/init.h>
  18 #include <linux/io.h>
  19 #include <linux/stddef.h>
  20 #include <linux/i2c.h>
  21 #include <linux/spi/spi.h>
  22 #include <linux/usb/musb.h>
  23 #include <linux/platform_data/spi-omap2-mcspi.h>
  24 #include <linux/platform_data/mtd-onenand-omap2.h>
  25 #include <sound/tlv320aic3x.h>
  26
  27 #include <asm/mach/arch.h>
  28 #include <asm/mach-types.h>
  29
  30 #include "common.h"
  31 #include <plat/menelaus.h>
  32 #include <plat/mmc.h>
  33
  34 #include "mux.h"
  35
  36 #define TUSB6010_ASYNC_CS       1
  37 #define TUSB6010_SYNC_CS        4
  38 #define TUSB6010_GPIO_INT       58
  39 #define TUSB6010_GPIO_ENABLE    0
  40 #define TUSB6010_DMACHAN        0x3f
  41
  42 #if defined(CONFIG_USB_MUSB_TUSB6010) || defined(CONFIG_USB_MUSB_TUSB6010_MODULE)
  43 /*
  44  * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
  45  * 1.5 V voltage regulators of PM companion chip. Companion chip will then
  46  * provide then PGOOD signal to TUSB6010 which will release it from reset.
  47  */
  48 static int tusb_set_power(int state)
  49 {
  50         int i, retval = 0;
  51
  52         if (state) {
  53                 gpio_set_value(TUSB6010_GPIO_ENABLE, 1);
  54                 msleep(1);
  55
  56                 /* Wait until TUSB6010 pulls INT pin down */
  57                 i = 100;
  58                 while (i && gpio_get_value(TUSB6010_GPIO_INT)) {
  59                         msleep(1);
  60                         i--;
  61                 }
  62
  63                 if (!i) {
  64                         printk(KERN_ERR "tusb: powerup failed\n");
  65                         retval = -ENODEV;
  66                 }
  67         } else {
  68                 gpio_set_value(TUSB6010_GPIO_ENABLE, 0);
  69                 msleep(10);
  70         }
  71
  72         return retval;
  73 }
  74
  75 static struct musb_hdrc_config musb_config = {
  76         .multipoint     = 1,
  77         .dyn_fifo       = 1,
  78         .num_eps        = 16,
  79         .ram_bits       = 12,
  80 };
  81
  82 static struct musb_hdrc_platform_data tusb_data = {
  83 #ifdef CONFIG_USB_GADGET_MUSB_HDRC
  84         .mode           = MUSB_OTG,
  85 #else
  86         .mode           = MUSB_HOST,
  87 #endif
  88         .set_power      = tusb_set_power,
  89         .min_power      = 25,   /* x2 = 50 mA drawn from VBUS as peripheral */
  90         .power          = 100,  /* Max 100 mA VBUS for host mode */
  91         .config         = &musb_config,
  92 };
  93
  94 static void __init n8x0_usb_init(void)
  95 {
  96         int ret = 0;
  97         static char     announce[] __initdata = KERN_INFO "TUSB 6010\n";
  98
  99         /* PM companion chip power control pin */
 100         ret = gpio_request_one(TUSB6010_GPIO_ENABLE, GPIOF_OUT_INIT_LOW,
 101                                "TUSB6010 enable");
 102         if (ret != 0) {
 103                 printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
 104                        TUSB6010_GPIO_ENABLE);
 105                 return;
 106         }
 107         tusb_set_power(0);
 108
 109         ret = tusb6010_setup_interface(&tusb_data, TUSB6010_REFCLK_19, 2,
 110                                         TUSB6010_ASYNC_CS, TUSB6010_SYNC_CS,
 111                                         TUSB6010_GPIO_INT, TUSB6010_DMACHAN);
 112         if (ret != 0)
 113                 goto err;
 114
 115         printk(announce);
 116
 117         return;
 118
 119 err:
 120         gpio_free(TUSB6010_GPIO_ENABLE);
 121 }
 122 #else
 123
 124 static void __init n8x0_usb_init(void) {}
 125
 126 #endif /*CONFIG_USB_MUSB_TUSB6010 */
 127
 128
 129 static struct omap2_mcspi_device_config p54spi_mcspi_config = {
 130         .turbo_mode     = 0,
 131 };
 132
 133 static struct spi_board_info n800_spi_board_info[] __initdata = {
 134         {
 135                 .modalias       = "p54spi",
 136                 .bus_num        = 2,
 137                 .chip_select    = 0,
 138                 .max_speed_hz   = 48000000,
 139                 .controller_data = &p54spi_mcspi_config,
 140         },
 141 };
 142
 143 #if defined(CONFIG_MTD_ONENAND_OMAP2) || \
 144         defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
 145
 146 static struct mtd_partition onenand_partitions[] = {
 147         {
 148                 .name           = "bootloader",
 149                 .offset         = 0,
 150                 .size           = 0x20000,
 151                 .mask_flags     = MTD_WRITEABLE,        /* Force read-only */
 152         },
 153         {
 154                 .name           = "config",
 155                 .offset         = MTDPART_OFS_APPEND,
 156                 .size           = 0x60000,
 157         },
 158         {
 159                 .name           = "kernel",
 160                 .offset         = MTDPART_OFS_APPEND,
 161                 .size           = 0x200000,
 162         },
 163         {
 164                 .name           = "initfs",
 165                 .offset         = MTDPART_OFS_APPEND,
 166                 .size           = 0x400000,
 167         },
 168         {
 169                 .name           = "rootfs",
 170                 .offset         = MTDPART_OFS_APPEND,
 171                 .size           = MTDPART_SIZ_FULL,
 172         },
 173 };
 174
 175 static struct omap_onenand_platform_data board_onenand_data[] = {
 176         {
 177                 .cs             = 0,
 178                 .gpio_irq       = 26,
 179                 .parts          = onenand_partitions,
 180                 .nr_parts       = ARRAY_SIZE(onenand_partitions),
 181                 .flags          = ONENAND_SYNC_READ,
 182         }
 183 };
 184 #endif
 185
 186 #if defined(CONFIG_MENELAUS) &&                                         \
 187         (defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE))
 188
 189 /*
 190  * On both N800 and N810, only the first of the two MMC controllers is in use.
 191  * The two MMC slots are multiplexed via Menelaus companion chip over I2C.
 192  * On N800, both slots are powered via Menelaus. On N810, only one of the
 193  * slots is powered via Menelaus. The N810 EMMC is powered via GPIO.
 194  *
 195  * VMMC                         slot 1 on both N800 and N810
 196  * VDCDC3_APE and VMCS2_APE     slot 2 on N800
 197  * GPIO23 and GPIO9             slot 2 EMMC on N810
 198  *
 199  */
 200 #define N8X0_SLOT_SWITCH_GPIO   96
 201 #define N810_EMMC_VSD_GPIO      23
 202 #define N810_EMMC_VIO_GPIO      9
 203
 204 static int slot1_cover_open;
 205 static int slot2_cover_open;
 206 static struct device *mmc_device;
 207
 208 static int n8x0_mmc_switch_slot(struct device *dev, int slot)
 209 {
 210 #ifdef CONFIG_MMC_DEBUG
 211         dev_dbg(dev, "Choose slot %d\n", slot + 1);
 212 #endif
 213         gpio_set_value(N8X0_SLOT_SWITCH_GPIO, slot);
 214         return 0;
 215 }
 216
 217 static int n8x0_mmc_set_power_menelaus(struct device *dev, int slot,
 218                                         int power_on, int vdd)
 219 {
 220         int mV;
 221
 222 #ifdef CONFIG_MMC_DEBUG
 223         dev_dbg(dev, "Set slot %d power: %s (vdd %d)\n", slot + 1,
 224                 power_on ? "on" : "off", vdd);
 225 #endif
 226         if (slot == 0) {
 227                 if (!power_on)
 228                         return menelaus_set_vmmc(0);
 229                 switch (1 << vdd) {
 230                 case MMC_VDD_33_34:
 231                 case MMC_VDD_32_33:
 232                 case MMC_VDD_31_32:
 233                         mV = 3100;
 234                         break;
 235                 case MMC_VDD_30_31:
 236                         mV = 3000;
 237                         break;
 238                 case MMC_VDD_28_29:
 239                         mV = 2800;
 240                         break;
 241                 case MMC_VDD_165_195:
 242                         mV = 1850;
 243                         break;
 244                 default:
 245                         BUG();
 246                 }
 247                 return menelaus_set_vmmc(mV);
 248         } else {
 249                 if (!power_on)
 250                         return menelaus_set_vdcdc(3, 0);
 251                 switch (1 << vdd) {
 252                 case MMC_VDD_33_34:
 253                 case MMC_VDD_32_33:
 254                         mV = 3300;
 255                         break;
 256                 case MMC_VDD_30_31:
 257                 case MMC_VDD_29_30:
 258                         mV = 3000;
 259                         break;
 260                 case MMC_VDD_28_29:
 261                 case MMC_VDD_27_28:
 262                         mV = 2800;
 263                         break;
 264                 case MMC_VDD_24_25:
 265                 case MMC_VDD_23_24:
 266                         mV = 2400;
 267                         break;
 268                 case MMC_VDD_22_23:
 269                 case MMC_VDD_21_22:
 270                         mV = 2200;
 271                         break;
 272                 case MMC_VDD_20_21:
 273                         mV = 2000;
 274                         break;
 275                 case MMC_VDD_165_195:
 276                         mV = 1800;
 277                         break;
 278                 default:
 279                         BUG();
 280                 }
 281                 return menelaus_set_vdcdc(3, mV);
 282         }
 283         return 0;
 284 }
 285
 286 static void n810_set_power_emmc(struct device *dev,
 287                                          int power_on)
 288 {
 289         dev_dbg(dev, "Set EMMC power %s\n", power_on ? "on" : "off");
 290
 291         if (power_on) {
 292                 gpio_set_value(N810_EMMC_VSD_GPIO, 1);
 293                 msleep(1);
 294                 gpio_set_value(N810_EMMC_VIO_GPIO, 1);
 295                 msleep(1);
 296         } else {
 297                 gpio_set_value(N810_EMMC_VIO_GPIO, 0);
 298                 msleep(50);
 299                 gpio_set_value(N810_EMMC_VSD_GPIO, 0);
 300                 msleep(50);
 301         }
 302 }
 303
 304 static int n8x0_mmc_set_power(struct device *dev, int slot, int power_on,
 305                               int vdd)
 306 {
 307         if (machine_is_nokia_n800() || slot == 0)
 308                 return n8x0_mmc_set_power_menelaus(dev, slot, power_on, vdd);
 309
 310         n810_set_power_emmc(dev, power_on);
 311
 312         return 0;
 313 }
 314
 315 static int n8x0_mmc_set_bus_mode(struct device *dev, int slot, int bus_mode)
 316 {
 317         int r;
 318
 319         dev_dbg(dev, "Set slot %d bus mode %s\n", slot + 1,
 320                 bus_mode == MMC_BUSMODE_OPENDRAIN ? "open-drain" : "push-pull");
 321         BUG_ON(slot != 0 && slot != 1);
 322         slot++;
 323         switch (bus_mode) {
 324         case MMC_BUSMODE_OPENDRAIN:
 325                 r = menelaus_set_mmc_opendrain(slot, 1);
 326                 break;
 327         case MMC_BUSMODE_PUSHPULL:
 328                 r = menelaus_set_mmc_opendrain(slot, 0);
 329                 break;
 330         default:
 331                 BUG();
 332         }
 333         if (r != 0 && printk_ratelimit())
 334                 dev_err(dev, "MMC: unable to set bus mode for slot %d\n",
 335                         slot);
 336         return r;
 337 }
 338
 339 static int n8x0_mmc_get_cover_state(struct device *dev, int slot)
 340 {
 341         slot++;
 342         BUG_ON(slot != 1 && slot != 2);
 343         if (slot == 1)
 344                 return slot1_cover_open;
 345         else
 346                 return slot2_cover_open;
 347 }
 348
 349 static void n8x0_mmc_callback(void *data, u8 card_mask)
 350 {
 351         int bit, *openp, index;
 352
 353         if (machine_is_nokia_n800()) {
 354                 bit = 1 << 1;
 355                 openp = &slot2_cover_open;
 356                 index = 1;
 357         } else {
 358                 bit = 1;
 359                 openp = &slot1_cover_open;
 360                 index = 0;
 361         }
 362
 363         if (card_mask & bit)
 364                 *openp = 1;
 365         else
 366                 *openp = 0;
 367
 368 #ifdef CONFIG_MMC_OMAP
 369         omap_mmc_notify_cover_event(mmc_device, index, *openp);
 370 #else
 371         pr_warn("MMC: notify cover event not available\n");
 372 #endif
 373 }
 374
 375 static int n8x0_mmc_late_init(struct device *dev)
 376 {
 377         int r, bit, *openp;
 378         int vs2sel;
 379
 380         mmc_device = dev;
 381
 382         r = menelaus_set_slot_sel(1);
 383         if (r < 0)
 384                 return r;
 385
 386         if (machine_is_nokia_n800())
 387                 vs2sel = 0;
 388         else
 389                 vs2sel = 2;
 390
 391         r = menelaus_set_mmc_slot(2, 0, vs2sel, 1);
 392         if (r < 0)
 393                 return r;
 394
 395         n8x0_mmc_set_power(dev, 0, MMC_POWER_ON, 16); /* MMC_VDD_28_29 */
 396         n8x0_mmc_set_power(dev, 1, MMC_POWER_ON, 16);
 397
 398         r = menelaus_set_mmc_slot(1, 1, 0, 1);
 399         if (r < 0)
 400                 return r;
 401         r = menelaus_set_mmc_slot(2, 1, vs2sel, 1);
 402         if (r < 0)
 403                 return r;
 404
 405         r = menelaus_get_slot_pin_states();
 406         if (r < 0)
 407                 return r;
 408
 409         if (machine_is_nokia_n800()) {
 410                 bit = 1 << 1;
 411                 openp = &slot2_cover_open;
 412         } else {
 413                 bit = 1;
 414                 openp = &slot1_cover_open;
 415                 slot2_cover_open = 0;
 416         }
 417
 418         /* All slot pin bits seem to be inversed until first switch change */
 419         if (r == 0xf || r == (0xf & ~bit))
 420                 r = ~r;
 421
 422         if (r & bit)
 423                 *openp = 1;
 424         else
 425                 *openp = 0;
 426
 427         r = menelaus_register_mmc_callback(n8x0_mmc_callback, NULL);
 428
 429         return r;
 430 }
 431
 432 static void n8x0_mmc_shutdown(struct device *dev)
 433 {
 434         int vs2sel;
 435
 436         if (machine_is_nokia_n800())
 437                 vs2sel = 0;
 438         else
 439                 vs2sel = 2;
 440
 441         menelaus_set_mmc_slot(1, 0, 0, 0);
 442         menelaus_set_mmc_slot(2, 0, vs2sel, 0);
 443 }
 444
 445 static void n8x0_mmc_cleanup(struct device *dev)
 446 {
 447         menelaus_unregister_mmc_callback();
 448
 449         gpio_free(N8X0_SLOT_SWITCH_GPIO);
 450
 451         if (machine_is_nokia_n810()) {
 452                 gpio_free(N810_EMMC_VSD_GPIO);
 453                 gpio_free(N810_EMMC_VIO_GPIO);
 454         }
 455 }
 456
 457 /*
 458  * MMC controller1 has two slots that are multiplexed via I2C.
 459  * MMC controller2 is not in use.
 460  */
 461 static struct omap_mmc_platform_data mmc1_data = {
 462         .nr_slots                       = 2,
 463         .switch_slot                    = n8x0_mmc_switch_slot,
 464         .init                           = n8x0_mmc_late_init,
 465         .cleanup                        = n8x0_mmc_cleanup,
 466         .shutdown                       = n8x0_mmc_shutdown,
 467         .max_freq                       = 24000000,
 468         .slots[0] = {
 469                 .wires                  = 4,
 470                 .set_power              = n8x0_mmc_set_power,
 471                 .set_bus_mode           = n8x0_mmc_set_bus_mode,
 472                 .get_cover_state        = n8x0_mmc_get_cover_state,
 473                 .ocr_mask               = MMC_VDD_165_195 | MMC_VDD_30_31 |
 474                                                 MMC_VDD_32_33   | MMC_VDD_33_34,
 475                 .name                   = "internal",
 476         },
 477         .slots[1] = {
 478                 .set_power              = n8x0_mmc_set_power,
 479                 .set_bus_mode           = n8x0_mmc_set_bus_mode,
 480                 .get_cover_state        = n8x0_mmc_get_cover_state,
 481                 .ocr_mask               = MMC_VDD_165_195 | MMC_VDD_20_21 |
 482                                                 MMC_VDD_21_22 | MMC_VDD_22_23 |
 483                                                 MMC_VDD_23_24 | MMC_VDD_24_25 |
 484                                                 MMC_VDD_27_28 | MMC_VDD_28_29 |
 485                                                 MMC_VDD_29_30 | MMC_VDD_30_31 |
 486                                                 MMC_VDD_32_33 | MMC_VDD_33_34,
 487                 .name                   = "external",
 488         },
 489 };
 490
 491 static struct omap_mmc_platform_data *mmc_data[OMAP24XX_NR_MMC];
 492
 493 static struct gpio n810_emmc_gpios[] __initdata = {
 494         { N810_EMMC_VSD_GPIO, GPIOF_OUT_INIT_LOW,  "MMC slot 2 Vddf" },
 495         { N810_EMMC_VIO_GPIO, GPIOF_OUT_INIT_LOW,  "MMC slot 2 Vdd"  },
 496 };
 497
 498 static void __init n8x0_mmc_init(void)
 499 {
 500         int err;
 501
 502         if (machine_is_nokia_n810()) {
 503                 mmc1_data.slots[0].name = "external";
 504
 505                 /*
 506                  * Some Samsung Movinand chips do not like open-ended
 507                  * multi-block reads and fall to braind-dead state
 508                  * while doing so. Reducing the number of blocks in
 509                  * the transfer or delays in clock disable do not help
 510                  */
 511                 mmc1_data.slots[1].name = "internal";
 512                 mmc1_data.slots[1].ban_openended = 1;
 513         }
 514
 515         err = gpio_request_one(N8X0_SLOT_SWITCH_GPIO, GPIOF_OUT_INIT_LOW,
 516                                "MMC slot switch");
 517         if (err)
 518                 return;
 519
 520         if (machine_is_nokia_n810()) {
 521                 err = gpio_request_array(n810_emmc_gpios,
 522                                          ARRAY_SIZE(n810_emmc_gpios));
 523                 if (err) {
 524                         gpio_free(N8X0_SLOT_SWITCH_GPIO);
 525                         return;
 526                 }
 527         }
 528
 529         mmc_data[0] = &mmc1_data;
 530         omap242x_init_mmc(mmc_data);
 531 }
 532 #else
 533
 534 void __init n8x0_mmc_init(void)
 535 {
 536 }
 537 #endif  /* CONFIG_MMC_OMAP */
 538
 539 #ifdef CONFIG_MENELAUS
 540
 541 static int n8x0_auto_sleep_regulators(void)
 542 {
 543         u32 val;
 544         int ret;
 545
 546         val = EN_VPLL_SLEEP | EN_VMMC_SLEEP    \
 547                 | EN_VAUX_SLEEP | EN_VIO_SLEEP \
 548                 | EN_VMEM_SLEEP | EN_DC3_SLEEP \
 549                 | EN_VC_SLEEP | EN_DC2_SLEEP;
 550
 551         ret = menelaus_set_regulator_sleep(1, val);
 552         if (ret < 0) {
 553                 pr_err("Could not set regulators to sleep on menelaus: %u\n",
 554                        ret);
 555                 return ret;
 556         }
 557         return 0;
 558 }
 559
 560 static int n8x0_auto_voltage_scale(void)
 561 {
 562         int ret;
 563
 564         ret = menelaus_set_vcore_hw(1400, 1050);
 565         if (ret < 0) {
 566                 pr_err("Could not set VCORE voltage on menelaus: %u\n", ret);
 567                 return ret;
 568         }
 569         return 0;
 570 }
 571
 572 static int n8x0_menelaus_late_init(struct device *dev)
 573 {
 574         int ret;
 575
 576         ret = n8x0_auto_voltage_scale();
 577         if (ret < 0)
 578                 return ret;
 579         ret = n8x0_auto_sleep_regulators();
 580         if (ret < 0)
 581                 return ret;
 582         return 0;
 583 }
 584
 585 #else
 586 static int n8x0_menelaus_late_init(struct device *dev)
 587 {
 588         return 0;
 589 }
 590 #endif
 591
 592 static struct menelaus_platform_data n8x0_menelaus_platform_data __initdata = {
 593         .late_init = n8x0_menelaus_late_init,
 594 };
 595
 596 static struct i2c_board_info __initdata n8x0_i2c_board_info_1[] __initdata = {
 597         {
 598                 I2C_BOARD_INFO("menelaus", 0x72),
 599                 .irq = 7 + OMAP_INTC_START,
 600                 .platform_data = &n8x0_menelaus_platform_data,
 601         },
 602 };
 603
 604 static struct aic3x_pdata n810_aic33_data __initdata = {
 605         .gpio_reset = 118,
 606 };
 607
 608 static struct i2c_board_info n810_i2c_board_info_2[] __initdata = {
 609         {
 610                 I2C_BOARD_INFO("tlv320aic3x", 0x18),
 611                 .platform_data = &n810_aic33_data,
 612         },
 613 };
 614
 615 #ifdef CONFIG_OMAP_MUX
 616 static struct omap_board_mux board_mux[] __initdata = {
 617         /* I2S codec port pins for McBSP block */
 618         OMAP2420_MUX(EAC_AC_SCLK, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
 619         OMAP2420_MUX(EAC_AC_FS, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
 620         OMAP2420_MUX(EAC_AC_DIN, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
 621         OMAP2420_MUX(EAC_AC_DOUT, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
 622         { .reg_offset = OMAP_MUX_TERMINATOR },
 623 };
 624
 625 static struct omap_device_pad serial2_pads[] __initdata = {
 626         {
 627                 .name   = "uart3_rx_irrx.uart3_rx_irrx",
 628                 .flags  = OMAP_DEVICE_PAD_REMUX | OMAP_DEVICE_PAD_WAKEUP,
 629                 .enable = OMAP_MUX_MODE0,
 630                 .idle   = OMAP_MUX_MODE3        /* Mux as GPIO for idle */
 631         },
 632 };
 633
 634 static inline void board_serial_init(void)
 635 {
 636         struct omap_board_data bdata;
 637
 638         bdata.flags = 0;
 639         bdata.pads = NULL;
 640         bdata.pads_cnt = 0;
 641
 642         bdata.id = 0;
 643         omap_serial_init_port(&bdata, NULL);
 644
 645         bdata.id = 1;
 646         omap_serial_init_port(&bdata, NULL);
 647
 648         bdata.id = 2;
 649         bdata.pads = serial2_pads;
 650         bdata.pads_cnt = ARRAY_SIZE(serial2_pads);
 651         omap_serial_init_port(&bdata, NULL);
 652 }
 653
 654 #else
 655
 656 static inline void board_serial_init(void)
 657 {
 658         omap_serial_init();
 659 }
 660
 661 #endif
 662
 663 static void __init n8x0_init_machine(void)
 664 {
 665         omap2420_mux_init(board_mux, OMAP_PACKAGE_ZAC);
 666         /* FIXME: add n810 spi devices */
 667         spi_register_board_info(n800_spi_board_info,
 668                                 ARRAY_SIZE(n800_spi_board_info));
 669         omap_register_i2c_bus(1, 400, n8x0_i2c_board_info_1,
 670                               ARRAY_SIZE(n8x0_i2c_board_info_1));
 671         omap_register_i2c_bus(2, 400, NULL, 0);
 672         if (machine_is_nokia_n810())
 673                 i2c_register_board_info(2, n810_i2c_board_info_2,
 674                                         ARRAY_SIZE(n810_i2c_board_info_2));
 675         board_serial_init();
 676         omap_sdrc_init(NULL, NULL);
 677         gpmc_onenand_init(board_onenand_data);
 678         n8x0_mmc_init();
 679         n8x0_usb_init();
 680 }
 681
 682 MACHINE_START(NOKIA_N800, "Nokia N800")
 683         .atag_offset    = 0x100,
 684         .reserve        = omap_reserve,
 685         .map_io         = omap242x_map_io,
 686         .init_early     = omap2420_init_early,
 687         .init_irq       = omap2_init_irq,
 688         .handle_irq     = omap2_intc_handle_irq,
 689         .init_machine   = n8x0_init_machine,
 690         .init_late      = omap2420_init_late,
 691         .timer          = &omap2_timer,
 692         .restart        = omap_prcm_restart,
 693 MACHINE_END
 694
 695 MACHINE_START(NOKIA_N810, "Nokia N810")
 696         .atag_offset    = 0x100,
 697         .reserve        = omap_reserve,
 698         .map_io         = omap242x_map_io,
 699         .init_early     = omap2420_init_early,
 700         .init_irq       = omap2_init_irq,
 701         .handle_irq     = omap2_intc_handle_irq,
 702         .init_machine   = n8x0_init_machine,
 703         .init_late      = omap2420_init_late,
 704         .timer          = &omap2_timer,
 705         .restart        = omap_prcm_restart,
 706 MACHINE_END
 707
 708 MACHINE_START(NOKIA_N810_WIMAX, "Nokia N810 WiMAX")
 709         .atag_offset    = 0x100,
 710         .reserve        = omap_reserve,
 711         .map_io         = omap242x_map_io,
 712         .init_early     = omap2420_init_early,
 713         .init_irq       = omap2_init_irq,
 714         .handle_irq     = omap2_intc_handle_irq,
 715         .init_machine   = n8x0_init_machine,
 716         .init_late      = omap2420_init_late,
 717         .timer          = &omap2_timer,
 718         .restart        = omap_prcm_restart,
 719 MACHINE_END