2 * linux/arch/arm/mach-omap2/board-n8x0.c
4 * Copyright (C) 2005-2009 Nokia Corporation
5 * Author: Juha Yrjola <juha.yrjola@nokia.com>
7 * Modified from mach-omap2/board-generic.c
9 * This program is free software; you can redistribute it and/or modify
10 * it under the terms of the GNU General Public License version 2 as
11 * published by the Free Software Foundation.
14 #include <linux/clk.h>
15 #include <linux/delay.h>
16 #include <linux/gpio.h>
17 #include <linux/init.h>
19 #include <linux/stddef.h>
20 #include <linux/i2c.h>
21 #include <linux/spi/spi.h>
22 #include <linux/usb/musb.h>
23 #include <linux/platform_data/spi-omap2-mcspi.h>
24 #include <linux/platform_data/mtd-onenand-omap2.h>
25 #include <linux/mfd/menelaus.h>
26 #include <sound/tlv320aic3x.h>
28 #include <asm/mach/arch.h>
29 #include <asm/mach-types.h>
35 #include "gpmc-onenand.h"
37 #define TUSB6010_ASYNC_CS 1
38 #define TUSB6010_SYNC_CS 4
39 #define TUSB6010_GPIO_INT 58
40 #define TUSB6010_GPIO_ENABLE 0
41 #define TUSB6010_DMACHAN 0x3f
43 #if defined(CONFIG_USB_MUSB_TUSB6010) || defined(CONFIG_USB_MUSB_TUSB6010_MODULE)
45 * Enable or disable power to TUSB6010. When enabling, turn on 3.3 V and
46 * 1.5 V voltage regulators of PM companion chip. Companion chip will then
47 * provide then PGOOD signal to TUSB6010 which will release it from reset.
49 static int tusb_set_power(int state
)
54 gpio_set_value(TUSB6010_GPIO_ENABLE
, 1);
57 /* Wait until TUSB6010 pulls INT pin down */
59 while (i
&& gpio_get_value(TUSB6010_GPIO_INT
)) {
65 printk(KERN_ERR
"tusb: powerup failed\n");
69 gpio_set_value(TUSB6010_GPIO_ENABLE
, 0);
76 static struct musb_hdrc_config musb_config
= {
83 static struct musb_hdrc_platform_data tusb_data
= {
84 #ifdef CONFIG_USB_GADGET_MUSB_HDRC
89 .set_power
= tusb_set_power
,
90 .min_power
= 25, /* x2 = 50 mA drawn from VBUS as peripheral */
91 .power
= 100, /* Max 100 mA VBUS for host mode */
92 .config
= &musb_config
,
95 static void __init
n8x0_usb_init(void)
98 static char announce
[] __initdata
= KERN_INFO
"TUSB 6010\n";
100 /* PM companion chip power control pin */
101 ret
= gpio_request_one(TUSB6010_GPIO_ENABLE
, GPIOF_OUT_INIT_LOW
,
104 printk(KERN_ERR
"Could not get TUSB power GPIO%i\n",
105 TUSB6010_GPIO_ENABLE
);
110 ret
= tusb6010_setup_interface(&tusb_data
, TUSB6010_REFCLK_19
, 2,
111 TUSB6010_ASYNC_CS
, TUSB6010_SYNC_CS
,
112 TUSB6010_GPIO_INT
, TUSB6010_DMACHAN
);
121 gpio_free(TUSB6010_GPIO_ENABLE
);
125 static void __init
n8x0_usb_init(void) {}
127 #endif /*CONFIG_USB_MUSB_TUSB6010 */
130 static struct omap2_mcspi_device_config p54spi_mcspi_config
= {
134 static struct spi_board_info n800_spi_board_info
[] __initdata
= {
136 .modalias
= "p54spi",
139 .max_speed_hz
= 48000000,
140 .controller_data
= &p54spi_mcspi_config
,
144 #if defined(CONFIG_MTD_ONENAND_OMAP2) || \
145 defined(CONFIG_MTD_ONENAND_OMAP2_MODULE)
147 static struct mtd_partition onenand_partitions
[] = {
149 .name
= "bootloader",
152 .mask_flags
= MTD_WRITEABLE
, /* Force read-only */
156 .offset
= MTDPART_OFS_APPEND
,
161 .offset
= MTDPART_OFS_APPEND
,
166 .offset
= MTDPART_OFS_APPEND
,
171 .offset
= MTDPART_OFS_APPEND
,
172 .size
= MTDPART_SIZ_FULL
,
176 static struct omap_onenand_platform_data board_onenand_data
[] = {
180 .parts
= onenand_partitions
,
181 .nr_parts
= ARRAY_SIZE(onenand_partitions
),
182 .flags
= ONENAND_SYNC_READ
,
187 #if defined(CONFIG_MENELAUS) && \
188 (defined(CONFIG_MMC_OMAP) || defined(CONFIG_MMC_OMAP_MODULE))
191 * On both N800 and N810, only the first of the two MMC controllers is in use.
192 * The two MMC slots are multiplexed via Menelaus companion chip over I2C.
193 * On N800, both slots are powered via Menelaus. On N810, only one of the
194 * slots is powered via Menelaus. The N810 EMMC is powered via GPIO.
196 * VMMC slot 1 on both N800 and N810
197 * VDCDC3_APE and VMCS2_APE slot 2 on N800
198 * GPIO23 and GPIO9 slot 2 EMMC on N810
201 #define N8X0_SLOT_SWITCH_GPIO 96
202 #define N810_EMMC_VSD_GPIO 23
203 #define N810_EMMC_VIO_GPIO 9
205 static int slot1_cover_open
;
206 static int slot2_cover_open
;
207 static struct device
*mmc_device
;
209 static int n8x0_mmc_switch_slot(struct device
*dev
, int slot
)
211 #ifdef CONFIG_MMC_DEBUG
212 dev_dbg(dev
, "Choose slot %d\n", slot
+ 1);
214 gpio_set_value(N8X0_SLOT_SWITCH_GPIO
, slot
);
218 static int n8x0_mmc_set_power_menelaus(struct device
*dev
, int slot
,
219 int power_on
, int vdd
)
223 #ifdef CONFIG_MMC_DEBUG
224 dev_dbg(dev
, "Set slot %d power: %s (vdd %d)\n", slot
+ 1,
225 power_on
? "on" : "off", vdd
);
229 return menelaus_set_vmmc(0);
242 case MMC_VDD_165_195
:
248 return menelaus_set_vmmc(mV
);
251 return menelaus_set_vdcdc(3, 0);
276 case MMC_VDD_165_195
:
282 return menelaus_set_vdcdc(3, mV
);
287 static void n810_set_power_emmc(struct device
*dev
,
290 dev_dbg(dev
, "Set EMMC power %s\n", power_on
? "on" : "off");
293 gpio_set_value(N810_EMMC_VSD_GPIO
, 1);
295 gpio_set_value(N810_EMMC_VIO_GPIO
, 1);
298 gpio_set_value(N810_EMMC_VIO_GPIO
, 0);
300 gpio_set_value(N810_EMMC_VSD_GPIO
, 0);
305 static int n8x0_mmc_set_power(struct device
*dev
, int slot
, int power_on
,
308 if (machine_is_nokia_n800() || slot
== 0)
309 return n8x0_mmc_set_power_menelaus(dev
, slot
, power_on
, vdd
);
311 n810_set_power_emmc(dev
, power_on
);
316 static int n8x0_mmc_set_bus_mode(struct device
*dev
, int slot
, int bus_mode
)
320 dev_dbg(dev
, "Set slot %d bus mode %s\n", slot
+ 1,
321 bus_mode
== MMC_BUSMODE_OPENDRAIN
? "open-drain" : "push-pull");
322 BUG_ON(slot
!= 0 && slot
!= 1);
325 case MMC_BUSMODE_OPENDRAIN
:
326 r
= menelaus_set_mmc_opendrain(slot
, 1);
328 case MMC_BUSMODE_PUSHPULL
:
329 r
= menelaus_set_mmc_opendrain(slot
, 0);
334 if (r
!= 0 && printk_ratelimit())
335 dev_err(dev
, "MMC: unable to set bus mode for slot %d\n",
340 static int n8x0_mmc_get_cover_state(struct device
*dev
, int slot
)
343 BUG_ON(slot
!= 1 && slot
!= 2);
345 return slot1_cover_open
;
347 return slot2_cover_open
;
350 static void n8x0_mmc_callback(void *data
, u8 card_mask
)
352 int bit
, *openp
, index
;
354 if (machine_is_nokia_n800()) {
356 openp
= &slot2_cover_open
;
360 openp
= &slot1_cover_open
;
369 #ifdef CONFIG_MMC_OMAP
370 omap_mmc_notify_cover_event(mmc_device
, index
, *openp
);
372 pr_warn("MMC: notify cover event not available\n");
376 static int n8x0_mmc_late_init(struct device
*dev
)
383 r
= menelaus_set_slot_sel(1);
387 if (machine_is_nokia_n800())
392 r
= menelaus_set_mmc_slot(2, 0, vs2sel
, 1);
396 n8x0_mmc_set_power(dev
, 0, MMC_POWER_ON
, 16); /* MMC_VDD_28_29 */
397 n8x0_mmc_set_power(dev
, 1, MMC_POWER_ON
, 16);
399 r
= menelaus_set_mmc_slot(1, 1, 0, 1);
402 r
= menelaus_set_mmc_slot(2, 1, vs2sel
, 1);
406 r
= menelaus_get_slot_pin_states();
410 if (machine_is_nokia_n800()) {
412 openp
= &slot2_cover_open
;
415 openp
= &slot1_cover_open
;
416 slot2_cover_open
= 0;
419 /* All slot pin bits seem to be inversed until first switch change */
420 if (r
== 0xf || r
== (0xf & ~bit
))
428 r
= menelaus_register_mmc_callback(n8x0_mmc_callback
, NULL
);
433 static void n8x0_mmc_shutdown(struct device
*dev
)
437 if (machine_is_nokia_n800())
442 menelaus_set_mmc_slot(1, 0, 0, 0);
443 menelaus_set_mmc_slot(2, 0, vs2sel
, 0);
446 static void n8x0_mmc_cleanup(struct device
*dev
)
448 menelaus_unregister_mmc_callback();
450 gpio_free(N8X0_SLOT_SWITCH_GPIO
);
452 if (machine_is_nokia_n810()) {
453 gpio_free(N810_EMMC_VSD_GPIO
);
454 gpio_free(N810_EMMC_VIO_GPIO
);
459 * MMC controller1 has two slots that are multiplexed via I2C.
460 * MMC controller2 is not in use.
462 static struct omap_mmc_platform_data mmc1_data
= {
464 .switch_slot
= n8x0_mmc_switch_slot
,
465 .init
= n8x0_mmc_late_init
,
466 .cleanup
= n8x0_mmc_cleanup
,
467 .shutdown
= n8x0_mmc_shutdown
,
468 .max_freq
= 24000000,
471 .set_power
= n8x0_mmc_set_power
,
472 .set_bus_mode
= n8x0_mmc_set_bus_mode
,
473 .get_cover_state
= n8x0_mmc_get_cover_state
,
474 .ocr_mask
= MMC_VDD_165_195
| MMC_VDD_30_31
|
475 MMC_VDD_32_33
| MMC_VDD_33_34
,
479 .set_power
= n8x0_mmc_set_power
,
480 .set_bus_mode
= n8x0_mmc_set_bus_mode
,
481 .get_cover_state
= n8x0_mmc_get_cover_state
,
482 .ocr_mask
= MMC_VDD_165_195
| MMC_VDD_20_21
|
483 MMC_VDD_21_22
| MMC_VDD_22_23
|
484 MMC_VDD_23_24
| MMC_VDD_24_25
|
485 MMC_VDD_27_28
| MMC_VDD_28_29
|
486 MMC_VDD_29_30
| MMC_VDD_30_31
|
487 MMC_VDD_32_33
| MMC_VDD_33_34
,
492 static struct omap_mmc_platform_data
*mmc_data
[OMAP24XX_NR_MMC
];
494 static struct gpio n810_emmc_gpios
[] __initdata
= {
495 { N810_EMMC_VSD_GPIO
, GPIOF_OUT_INIT_LOW
, "MMC slot 2 Vddf" },
496 { N810_EMMC_VIO_GPIO
, GPIOF_OUT_INIT_LOW
, "MMC slot 2 Vdd" },
499 static void __init
n8x0_mmc_init(void)
503 if (machine_is_nokia_n810()) {
504 mmc1_data
.slots
[0].name
= "external";
507 * Some Samsung Movinand chips do not like open-ended
508 * multi-block reads and fall to braind-dead state
509 * while doing so. Reducing the number of blocks in
510 * the transfer or delays in clock disable do not help
512 mmc1_data
.slots
[1].name
= "internal";
513 mmc1_data
.slots
[1].ban_openended
= 1;
516 err
= gpio_request_one(N8X0_SLOT_SWITCH_GPIO
, GPIOF_OUT_INIT_LOW
,
521 if (machine_is_nokia_n810()) {
522 err
= gpio_request_array(n810_emmc_gpios
,
523 ARRAY_SIZE(n810_emmc_gpios
));
525 gpio_free(N8X0_SLOT_SWITCH_GPIO
);
530 mmc_data
[0] = &mmc1_data
;
531 omap242x_init_mmc(mmc_data
);
535 void __init
n8x0_mmc_init(void)
538 #endif /* CONFIG_MMC_OMAP */
540 #ifdef CONFIG_MENELAUS
542 static int n8x0_auto_sleep_regulators(void)
547 val
= EN_VPLL_SLEEP
| EN_VMMC_SLEEP \
548 | EN_VAUX_SLEEP
| EN_VIO_SLEEP \
549 | EN_VMEM_SLEEP
| EN_DC3_SLEEP \
550 | EN_VC_SLEEP
| EN_DC2_SLEEP
;
552 ret
= menelaus_set_regulator_sleep(1, val
);
554 pr_err("Could not set regulators to sleep on menelaus: %u\n",
561 static int n8x0_auto_voltage_scale(void)
565 ret
= menelaus_set_vcore_hw(1400, 1050);
567 pr_err("Could not set VCORE voltage on menelaus: %u\n", ret
);
573 static int n8x0_menelaus_late_init(struct device
*dev
)
577 ret
= n8x0_auto_voltage_scale();
580 ret
= n8x0_auto_sleep_regulators();
587 static int n8x0_menelaus_late_init(struct device
*dev
)
593 static struct menelaus_platform_data n8x0_menelaus_platform_data __initdata
= {
594 .late_init
= n8x0_menelaus_late_init
,
597 static struct i2c_board_info __initdata n8x0_i2c_board_info_1
[] __initdata
= {
599 I2C_BOARD_INFO("menelaus", 0x72),
600 .irq
= 7 + OMAP_INTC_START
,
601 .platform_data
= &n8x0_menelaus_platform_data
,
605 static struct aic3x_pdata n810_aic33_data __initdata
= {
609 static struct i2c_board_info n810_i2c_board_info_2
[] __initdata
= {
611 I2C_BOARD_INFO("tlv320aic3x", 0x18),
612 .platform_data
= &n810_aic33_data
,
616 #ifdef CONFIG_OMAP_MUX
617 static struct omap_board_mux board_mux
[] __initdata
= {
618 /* I2S codec port pins for McBSP block */
619 OMAP2420_MUX(EAC_AC_SCLK
, OMAP_MUX_MODE1
| OMAP_PIN_INPUT
),
620 OMAP2420_MUX(EAC_AC_FS
, OMAP_MUX_MODE1
| OMAP_PIN_INPUT
),
621 OMAP2420_MUX(EAC_AC_DIN
, OMAP_MUX_MODE1
| OMAP_PIN_INPUT
),
622 OMAP2420_MUX(EAC_AC_DOUT
, OMAP_MUX_MODE1
| OMAP_PIN_OUTPUT
),
623 { .reg_offset
= OMAP_MUX_TERMINATOR
},
626 static struct omap_device_pad serial2_pads
[] __initdata
= {
628 .name
= "uart3_rx_irrx.uart3_rx_irrx",
629 .flags
= OMAP_DEVICE_PAD_REMUX
| OMAP_DEVICE_PAD_WAKEUP
,
630 .enable
= OMAP_MUX_MODE0
,
631 .idle
= OMAP_MUX_MODE3
/* Mux as GPIO for idle */
635 static inline void board_serial_init(void)
637 struct omap_board_data bdata
;
644 omap_serial_init_port(&bdata
, NULL
);
647 omap_serial_init_port(&bdata
, NULL
);
650 bdata
.pads
= serial2_pads
;
651 bdata
.pads_cnt
= ARRAY_SIZE(serial2_pads
);
652 omap_serial_init_port(&bdata
, NULL
);
657 static inline void board_serial_init(void)
664 static void __init
n8x0_init_machine(void)
666 omap2420_mux_init(board_mux
, OMAP_PACKAGE_ZAC
);
667 /* FIXME: add n810 spi devices */
668 spi_register_board_info(n800_spi_board_info
,
669 ARRAY_SIZE(n800_spi_board_info
));
670 omap_register_i2c_bus(1, 400, n8x0_i2c_board_info_1
,
671 ARRAY_SIZE(n8x0_i2c_board_info_1
));
672 omap_register_i2c_bus(2, 400, NULL
, 0);
673 if (machine_is_nokia_n810())
674 i2c_register_board_info(2, n810_i2c_board_info_2
,
675 ARRAY_SIZE(n810_i2c_board_info_2
));
677 omap_sdrc_init(NULL
, NULL
);
678 gpmc_onenand_init(board_onenand_data
);
683 MACHINE_START(NOKIA_N800
, "Nokia N800")
684 .atag_offset
= 0x100,
685 .reserve
= omap_reserve
,
686 .map_io
= omap242x_map_io
,
687 .init_early
= omap2420_init_early
,
688 .init_irq
= omap2_init_irq
,
689 .handle_irq
= omap2_intc_handle_irq
,
690 .init_machine
= n8x0_init_machine
,
691 .init_late
= omap2420_init_late
,
692 .timer
= &omap2_timer
,
693 .restart
= omap2xxx_restart
,
696 MACHINE_START(NOKIA_N810
, "Nokia N810")
697 .atag_offset
= 0x100,
698 .reserve
= omap_reserve
,
699 .map_io
= omap242x_map_io
,
700 .init_early
= omap2420_init_early
,
701 .init_irq
= omap2_init_irq
,
702 .handle_irq
= omap2_intc_handle_irq
,
703 .init_machine
= n8x0_init_machine
,
704 .init_late
= omap2420_init_late
,
705 .timer
= &omap2_timer
,
706 .restart
= omap2xxx_restart
,
709 MACHINE_START(NOKIA_N810_WIMAX
, "Nokia N810 WiMAX")
710 .atag_offset
= 0x100,
711 .reserve
= omap_reserve
,
712 .map_io
= omap242x_map_io
,
713 .init_early
= omap2420_init_early
,
714 .init_irq
= omap2_init_irq
,
715 .handle_irq
= omap2_intc_handle_irq
,
716 .init_machine
= n8x0_init_machine
,
717 .init_late
= omap2420_init_late
,
718 .timer
= &omap2_timer
,
719 .restart
= omap2xxx_restart
,