arch/arm/mach-orion5x/terastation_pro2-setup.c

   1 /*
   2  * Buffalo Terastation Pro II/Live Board Setup
   3  *
   4  * Maintainer: Sylver Bruneau <sylver.bruneau@googlemail.com>
   5  *
   6  * This program is free software; you can redistribute it and/or
   7  * modify it under the terms of the GNU General Public License
   8  * as published by the Free Software Foundation; either version
   9  * 2 of the License, or (at your option) any later version.
  10  */
  11 #include <linux/gpio.h>
  12 #include <linux/kernel.h>
  13 #include <linux/init.h>
  14 #include <linux/platform_device.h>
  15 #include <linux/pci.h>
  16 #include <linux/irq.h>
  17 #include <linux/delay.h>
  18 #include <linux/mtd/physmap.h>
  19 #include <linux/mv643xx_eth.h>
  20 #include <linux/i2c.h>
  21 #include <linux/serial_reg.h>
  22 #include <asm/mach-types.h>
  23 #include <asm/mach/arch.h>
  24 #include <asm/mach/pci.h>
  25 #include <mach/orion5x.h>
  26 #include "common.h"
  27 #include "mpp.h"
  28
  29 /*****************************************************************************
  30  * Terastation Pro 2/Live Info
  31  ****************************************************************************/
  32
  33 /*
  34  * Terastation Pro 2 hardware :
  35  * - Marvell 88F5281-D0
  36  * - Marvell 88SX6042 SATA controller (PCI)
  37  * - Marvell 88E1118 Gigabit Ethernet PHY
  38  * - 256KB NOR flash
  39  * - 128MB of DDR RAM
  40  * - PCIe port (not equipped)
  41  */
  42
  43 /*
  44  * 256K NOR flash Device bus boot chip select
  45  */
  46
  47 #define TSP2_NOR_BOOT_BASE      0xf4000000
  48 #define TSP2_NOR_BOOT_SIZE      SZ_256K
  49
  50 /*****************************************************************************
  51  * 256KB NOR Flash on BOOT Device
  52  ****************************************************************************/
  53
  54 static struct physmap_flash_data tsp2_nor_flash_data = {
  55         .width    = 1,
  56 };
  57
  58 static struct resource tsp2_nor_flash_resource = {
  59         .flags = IORESOURCE_MEM,
  60         .start = TSP2_NOR_BOOT_BASE,
  61         .end   = TSP2_NOR_BOOT_BASE + TSP2_NOR_BOOT_SIZE - 1,
  62 };
  63
  64 static struct platform_device tsp2_nor_flash = {
  65         .name          = "physmap-flash",
  66         .id            = 0,
  67         .dev           = {
  68                 .platform_data  = &tsp2_nor_flash_data,
  69         },
  70         .num_resources = 1,
  71         .resource      = &tsp2_nor_flash_resource,
  72 };
  73
  74 /*****************************************************************************
  75  * PCI
  76  ****************************************************************************/
  77 #define TSP2_PCI_SLOT0_OFFS             7
  78 #define TSP2_PCI_SLOT0_IRQ_PIN          11
  79
  80 static void __init tsp2_pci_preinit(void)
  81 {
  82         int pin;
  83
  84         /*
  85          * Configure PCI GPIO IRQ pins
  86          */
  87         pin = TSP2_PCI_SLOT0_IRQ_PIN;
  88         if (gpio_request(pin, "PCI Int1") == 0) {
  89                 if (gpio_direction_input(pin) == 0) {
  90                         irq_set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW);
  91                 } else {
  92                         printk(KERN_ERR "tsp2_pci_preinit failed "
  93                                         "to set_irq_type pin %d\n", pin);
  94                         gpio_free(pin);
  95                 }
  96         } else {
  97                 printk(KERN_ERR "tsp2_pci_preinit failed to "
  98                                 "gpio_request %d\n", pin);
  99         }
 100 }
 101
 102 static int __init tsp2_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
 103 {
 104         int irq;
 105
 106         /*
 107          * Check for devices with hard-wired IRQs.
 108          */
 109         irq = orion5x_pci_map_irq(dev, slot, pin);
 110         if (irq != -1)
 111                 return irq;
 112
 113         /*
 114          * PCI IRQs are connected via GPIOs.
 115          */
 116         if (slot == TSP2_PCI_SLOT0_OFFS)
 117                 return gpio_to_irq(TSP2_PCI_SLOT0_IRQ_PIN);
 118
 119         return -1;
 120 }
 121
 122 static struct hw_pci tsp2_pci __initdata = {
 123         .nr_controllers = 2,
 124         .preinit        = tsp2_pci_preinit,
 125         .setup          = orion5x_pci_sys_setup,
 126         .scan           = orion5x_pci_sys_scan_bus,
 127         .map_irq        = tsp2_pci_map_irq,
 128 };
 129
 130 static int __init tsp2_pci_init(void)
 131 {
 132         if (machine_is_terastation_pro2())
 133                 pci_common_init(&tsp2_pci);
 134
 135         return 0;
 136 }
 137
 138 subsys_initcall(tsp2_pci_init);
 139
 140 /*****************************************************************************
 141  * Ethernet
 142  ****************************************************************************/
 143
 144 static struct mv643xx_eth_platform_data tsp2_eth_data = {
 145         .phy_addr       = 0,
 146 };
 147
 148 /*****************************************************************************
 149  * RTC 5C372a on I2C bus
 150  ****************************************************************************/
 151
 152 #define TSP2_RTC_GPIO   9
 153
 154 static struct i2c_board_info __initdata tsp2_i2c_rtc = {
 155         I2C_BOARD_INFO("rs5c372a", 0x32),
 156 };
 157
 158 /*****************************************************************************
 159  * Terastation Pro II specific power off method via UART1-attached
 160  * microcontroller
 161  ****************************************************************************/
 162
 163 #define UART1_REG(x)    (UART1_VIRT_BASE + ((UART_##x) << 2))
 164
 165 static int tsp2_miconread(unsigned char *buf, int count)
 166 {
 167         int i;
 168         int timeout;
 169
 170         for (i = 0; i < count; i++) {
 171                 timeout = 10;
 172
 173                 while (!(readl(UART1_REG(LSR)) & UART_LSR_DR)) {
 174                         if (--timeout == 0)
 175                                 break;
 176                         udelay(1000);
 177                 }
 178
 179                 if (timeout == 0)
 180                         break;
 181                 buf[i] = readl(UART1_REG(RX));
 182         }
 183
 184         /* return read bytes */
 185         return i;
 186 }
 187
 188 static int tsp2_miconwrite(const unsigned char *buf, int count)
 189 {
 190         int i = 0;
 191
 192         while (count--) {
 193                 while (!(readl(UART1_REG(LSR)) & UART_LSR_THRE))
 194                         barrier();
 195                 writel(buf[i++], UART1_REG(TX));
 196         }
 197
 198         return 0;
 199 }
 200
 201 static int tsp2_miconsend(const unsigned char *data, int count)
 202 {
 203         int i;
 204         unsigned char checksum = 0;
 205         unsigned char recv_buf[40];
 206         unsigned char send_buf[40];
 207         unsigned char correct_ack[3];
 208         int retry = 2;
 209
 210         /* Generate checksum */
 211         for (i = 0; i < count; i++)
 212                 checksum -=  data[i];
 213
 214         do {
 215                 /* Send data */
 216                 tsp2_miconwrite(data, count);
 217
 218                 /* send checksum */
 219                 tsp2_miconwrite(&checksum, 1);
 220
 221                 if (tsp2_miconread(recv_buf, sizeof(recv_buf)) <= 3) {
 222                         printk(KERN_ERR ">%s: receive failed.\n", __func__);
 223
 224                         /* send preamble to clear the receive buffer */
 225                         memset(&send_buf, 0xff, sizeof(send_buf));
 226                         tsp2_miconwrite(send_buf, sizeof(send_buf));
 227
 228                         /* make dummy reads */
 229                         mdelay(100);
 230                         tsp2_miconread(recv_buf, sizeof(recv_buf));
 231                 } else {
 232                         /* Generate expected ack */
 233                         correct_ack[0] = 0x01;
 234                         correct_ack[1] = data[1];
 235                         correct_ack[2] = 0x00;
 236
 237                         /* checksum Check */
 238                         if ((recv_buf[0] + recv_buf[1] + recv_buf[2] +
 239                              recv_buf[3]) & 0xFF) {
 240                                 printk(KERN_ERR ">%s: Checksum Error : "
 241                                         "Received data[%02x, %02x, %02x, %02x]"
 242                                         "\n", __func__, recv_buf[0],
 243                                         recv_buf[1], recv_buf[2], recv_buf[3]);
 244                         } else {
 245                                 /* Check Received Data */
 246                                 if (correct_ack[0] == recv_buf[0] &&
 247                                     correct_ack[1] == recv_buf[1] &&
 248                                     correct_ack[2] == recv_buf[2]) {
 249                                         /* Interval for next command */
 250                                         mdelay(10);
 251
 252                                         /* Receive ACK */
 253                                         return 0;
 254                                 }
 255                         }
 256                         /* Received NAK or illegal Data */
 257                         printk(KERN_ERR ">%s: Error : NAK or Illegal Data "
 258                                         "Received\n", __func__);
 259                 }
 260         } while (retry--);
 261
 262         /* Interval for next command */
 263         mdelay(10);
 264
 265         return -1;
 266 }
 267
 268 static void tsp2_power_off(void)
 269 {
 270         const unsigned char watchdogkill[]      = {0x01, 0x35, 0x00};
 271         const unsigned char shutdownwait[]      = {0x00, 0x0c};
 272         const unsigned char poweroff[]          = {0x00, 0x06};
 273         /* 38400 baud divisor */
 274         const unsigned divisor = ((orion5x_tclk + (8 * 38400)) / (16 * 38400));
 275
 276         pr_info("%s: triggering power-off...\n", __func__);
 277
 278         /* hijack uart1 and reset into sane state (38400,8n1,even parity) */
 279         writel(0x83, UART1_REG(LCR));
 280         writel(divisor & 0xff, UART1_REG(DLL));
 281         writel((divisor >> 8) & 0xff, UART1_REG(DLM));
 282         writel(0x1b, UART1_REG(LCR));
 283         writel(0x00, UART1_REG(IER));
 284         writel(0x07, UART1_REG(FCR));
 285         writel(0x00, UART1_REG(MCR));
 286
 287         /* Send the commands to shutdown the Terastation Pro II */
 288         tsp2_miconsend(watchdogkill, sizeof(watchdogkill)) ;
 289         tsp2_miconsend(shutdownwait, sizeof(shutdownwait)) ;
 290         tsp2_miconsend(poweroff, sizeof(poweroff));
 291 }
 292
 293 /*****************************************************************************
 294  * General Setup
 295  ****************************************************************************/
 296 static unsigned int tsp2_mpp_modes[] __initdata = {
 297         MPP0_PCIE_RST_OUTn,
 298         MPP1_UNUSED,
 299         MPP2_UNUSED,
 300         MPP3_UNUSED,
 301         MPP4_NAND,              /* BOOT NAND Flash REn */
 302         MPP5_NAND,              /* BOOT NAND Flash WEn */
 303         MPP6_NAND,              /* BOOT NAND Flash HREn[0] */
 304         MPP7_NAND,              /* BOOT NAND Flash WEn[0] */
 305         MPP8_GPIO,              /* MICON int */
 306         MPP9_GPIO,              /* RTC int */
 307         MPP10_UNUSED,
 308         MPP11_GPIO,             /* PCI Int A */
 309         MPP12_UNUSED,
 310         MPP13_GPIO,             /* UPS on UART0 enable */
 311         MPP14_GPIO,             /* UPS low battery detection */
 312         MPP15_UNUSED,
 313         MPP16_UART,             /* UART1 RXD */
 314         MPP17_UART,             /* UART1 TXD */
 315         MPP18_UART,             /* UART1 CTSn */
 316         MPP19_UART,             /* UART1 RTSn */
 317         0,
 318 };
 319
 320 static void __init tsp2_init(void)
 321 {
 322         /*
 323          * Setup basic Orion functions. Need to be called early.
 324          */
 325         orion5x_init();
 326
 327         orion5x_mpp_conf(tsp2_mpp_modes);
 328
 329         /*
 330          * Configure peripherals.
 331          */
 332         mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET,
 333                                     ORION_MBUS_DEVBUS_BOOT_ATTR,
 334                                     TSP2_NOR_BOOT_BASE,
 335                                     TSP2_NOR_BOOT_SIZE);
 336         platform_device_register(&tsp2_nor_flash);
 337
 338         orion5x_ehci0_init();
 339         orion5x_eth_init(&tsp2_eth_data);
 340         orion5x_i2c_init();
 341         orion5x_uart0_init();
 342         orion5x_uart1_init();
 343
 344         /* Get RTC IRQ and register the chip */
 345         if (gpio_request(TSP2_RTC_GPIO, "rtc") == 0) {
 346                 if (gpio_direction_input(TSP2_RTC_GPIO) == 0)
 347                         tsp2_i2c_rtc.irq = gpio_to_irq(TSP2_RTC_GPIO);
 348                 else
 349                         gpio_free(TSP2_RTC_GPIO);
 350         }
 351         if (tsp2_i2c_rtc.irq == 0)
 352                 pr_warn("tsp2_init: failed to get RTC IRQ\n");
 353         i2c_register_board_info(0, &tsp2_i2c_rtc, 1);
 354
 355         /* register Terastation Pro II specific power-off method */
 356         pm_power_off = tsp2_power_off;
 357 }
 358
 359 MACHINE_START(TERASTATION_PRO2, "Buffalo Terastation Pro II/Live")
 360         /* Maintainer:  Sylver Bruneau <sylver.bruneau@googlemail.com> */
 361         .atag_offset    = 0x100,
 362         .init_machine   = tsp2_init,
 363         .map_io         = orion5x_map_io,
 364         .init_early     = orion5x_init_early,
 365         .init_irq       = orion5x_init_irq,
 366         .init_time      = orion5x_timer_init,
 367         .fixup          = tag_fixup_mem32,
 368         .restart        = orion5x_restart,
 369 MACHINE_END