arch/arm/mach-pxa/am300epd.c

   1 /*
   2  * am300epd.c -- Platform device for AM300 EPD kit
   3  *
   4  * Copyright (C) 2008, Jaya Kumar
   5  *
   6  * This file is subject to the terms and conditions of the GNU General Public
   7  * License. See the file COPYING in the main directory of this archive for
   8  * more details.
   9  *
  10  * This work was made possible by help and equipment support from E-Ink
  11  * Corporation. http://support.eink.com/community
  12  *
  13  * This driver is written to be used with the Broadsheet display controller.
  14  * on the AM300 EPD prototype kit/development kit with an E-Ink 800x600
  15  * Vizplex EPD on a Gumstix board using the Broadsheet interface board.
  16  *
  17  */
  18
  19 #include <linux/module.h>
  20 #include <linux/kernel.h>
  21 #include <linux/errno.h>
  22 #include <linux/string.h>
  23 #include <linux/delay.h>
  24 #include <linux/interrupt.h>
  25 #include <linux/fb.h>
  26 #include <linux/init.h>
  27 #include <linux/platform_device.h>
  28 #include <linux/irq.h>
  29 #include <linux/gpio.h>
  30
  31 #include <mach/gumstix.h>
  32 #include <mach/mfp-pxa25x.h>
  33 #include <linux/platform_data/video-pxafb.h>
  34
  35 #include "generic.h"
  36
  37 #include <video/broadsheetfb.h>
  38
  39 static unsigned int panel_type = 6;
  40 static struct platform_device *am300_device;
  41 static struct broadsheet_board am300_board;
  42
  43 static unsigned long am300_pin_config[] __initdata = {
  44         GPIO16_GPIO,
  45         GPIO17_GPIO,
  46         GPIO32_GPIO,
  47         GPIO48_GPIO,
  48         GPIO49_GPIO,
  49         GPIO51_GPIO,
  50         GPIO74_GPIO,
  51         GPIO75_GPIO,
  52         GPIO76_GPIO,
  53         GPIO77_GPIO,
  54
  55         /* this is the 16-bit hdb bus 58-73 */
  56         GPIO58_GPIO,
  57         GPIO59_GPIO,
  58         GPIO60_GPIO,
  59         GPIO61_GPIO,
  60
  61         GPIO62_GPIO,
  62         GPIO63_GPIO,
  63         GPIO64_GPIO,
  64         GPIO65_GPIO,
  65
  66         GPIO66_GPIO,
  67         GPIO67_GPIO,
  68         GPIO68_GPIO,
  69         GPIO69_GPIO,
  70
  71         GPIO70_GPIO,
  72         GPIO71_GPIO,
  73         GPIO72_GPIO,
  74         GPIO73_GPIO,
  75 };
  76
  77 /* register offsets for gpio control */
  78 #define PWR_GPIO_PIN    16
  79 #define CFG_GPIO_PIN    17
  80 #define RDY_GPIO_PIN    32
  81 #define DC_GPIO_PIN     48
  82 #define RST_GPIO_PIN    49
  83 #define LED_GPIO_PIN    51
  84 #define RD_GPIO_PIN     74
  85 #define WR_GPIO_PIN     75
  86 #define CS_GPIO_PIN     76
  87 #define IRQ_GPIO_PIN    77
  88
  89 /* hdb bus */
  90 #define DB0_GPIO_PIN    58
  91 #define DB15_GPIO_PIN   73
  92
  93 static int gpios[] = { PWR_GPIO_PIN, CFG_GPIO_PIN, RDY_GPIO_PIN, DC_GPIO_PIN,
  94                         RST_GPIO_PIN, RD_GPIO_PIN, WR_GPIO_PIN, CS_GPIO_PIN,
  95                         IRQ_GPIO_PIN, LED_GPIO_PIN };
  96 static char *gpio_names[] = { "PWR", "CFG", "RDY", "DC", "RST", "RD", "WR",
  97                                 "CS", "IRQ", "LED" };
  98
  99 static int am300_wait_event(struct broadsheetfb_par *par)
 100 {
 101         /* todo: improve err recovery */
 102         wait_event(par->waitq, gpio_get_value(RDY_GPIO_PIN));
 103         return 0;
 104 }
 105
 106 static int am300_init_gpio_regs(struct broadsheetfb_par *par)
 107 {
 108         int i;
 109         int err;
 110         char dbname[8];
 111
 112         for (i = 0; i < ARRAY_SIZE(gpios); i++) {
 113                 err = gpio_request(gpios[i], gpio_names[i]);
 114                 if (err) {
 115                         dev_err(&am300_device->dev, "failed requesting "
 116                                 "gpio %s, err=%d\n", gpio_names[i], err);
 117                         goto err_req_gpio;
 118                 }
 119         }
 120
 121         /* we also need to take care of the hdb bus */
 122         for (i = DB0_GPIO_PIN; i <= DB15_GPIO_PIN; i++) {
 123                 sprintf(dbname, "DB%d", i);
 124                 err = gpio_request(i, dbname);
 125                 if (err) {
 126                         dev_err(&am300_device->dev, "failed requesting "
 127                                 "gpio %d, err=%d\n", i, err);
 128                         goto err_req_gpio2;
 129                 }
 130         }
 131
 132         /* setup the outputs and init values */
 133         gpio_direction_output(PWR_GPIO_PIN, 0);
 134         gpio_direction_output(CFG_GPIO_PIN, 1);
 135         gpio_direction_output(DC_GPIO_PIN, 0);
 136         gpio_direction_output(RD_GPIO_PIN, 1);
 137         gpio_direction_output(WR_GPIO_PIN, 1);
 138         gpio_direction_output(CS_GPIO_PIN, 1);
 139         gpio_direction_output(RST_GPIO_PIN, 0);
 140
 141         /* setup the inputs */
 142         gpio_direction_input(RDY_GPIO_PIN);
 143         gpio_direction_input(IRQ_GPIO_PIN);
 144
 145         /* start the hdb bus as an input */
 146         for (i = DB0_GPIO_PIN; i <= DB15_GPIO_PIN; i++)
 147                 gpio_direction_output(i, 0);
 148
 149         /* go into command mode */
 150         gpio_set_value(CFG_GPIO_PIN, 1);
 151         gpio_set_value(RST_GPIO_PIN, 0);
 152         msleep(10);
 153         gpio_set_value(RST_GPIO_PIN, 1);
 154         msleep(10);
 155         am300_wait_event(par);
 156
 157         return 0;
 158
 159 err_req_gpio2:
 160         while (--i >= DB0_GPIO_PIN)
 161                 gpio_free(i);
 162         i = ARRAY_SIZE(gpios);
 163 err_req_gpio:
 164         while (--i >= 0)
 165                 gpio_free(gpios[i]);
 166
 167         return err;
 168 }
 169
 170 static int am300_init_board(struct broadsheetfb_par *par)
 171 {
 172         return am300_init_gpio_regs(par);
 173 }
 174
 175 static void am300_cleanup(struct broadsheetfb_par *par)
 176 {
 177         int i;
 178
 179         free_irq(PXA_GPIO_TO_IRQ(RDY_GPIO_PIN), par);
 180
 181         for (i = 0; i < ARRAY_SIZE(gpios); i++)
 182                 gpio_free(gpios[i]);
 183
 184         for (i = DB0_GPIO_PIN; i <= DB15_GPIO_PIN; i++)
 185                 gpio_free(i);
 186
 187 }
 188
 189 static u16 am300_get_hdb(struct broadsheetfb_par *par)
 190 {
 191         u16 res = 0;
 192         int i;
 193
 194         for (i = 0; i <= (DB15_GPIO_PIN - DB0_GPIO_PIN) ; i++)
 195                 res |= (gpio_get_value(DB0_GPIO_PIN + i)) ? (1 << i) : 0;
 196
 197         return res;
 198 }
 199
 200 static void am300_set_hdb(struct broadsheetfb_par *par, u16 data)
 201 {
 202         int i;
 203
 204         for (i = 0; i <= (DB15_GPIO_PIN - DB0_GPIO_PIN) ; i++)
 205                 gpio_set_value(DB0_GPIO_PIN + i, (data >> i) & 0x01);
 206 }
 207
 208
 209 static void am300_set_ctl(struct broadsheetfb_par *par, unsigned char bit,
 210                                 u8 state)
 211 {
 212         switch (bit) {
 213         case BS_CS:
 214                 gpio_set_value(CS_GPIO_PIN, state);
 215                 break;
 216         case BS_DC:
 217                 gpio_set_value(DC_GPIO_PIN, state);
 218                 break;
 219         case BS_WR:
 220                 gpio_set_value(WR_GPIO_PIN, state);
 221                 break;
 222         }
 223 }
 224
 225 static int am300_get_panel_type(void)
 226 {
 227         return panel_type;
 228 }
 229
 230 static irqreturn_t am300_handle_irq(int irq, void *dev_id)
 231 {
 232         struct broadsheetfb_par *par = dev_id;
 233
 234         wake_up(&par->waitq);
 235         return IRQ_HANDLED;
 236 }
 237
 238 static int am300_setup_irq(struct fb_info *info)
 239 {
 240         int ret;
 241         struct broadsheetfb_par *par = info->par;
 242
 243         ret = request_irq(PXA_GPIO_TO_IRQ(RDY_GPIO_PIN), am300_handle_irq,
 244                                 IRQF_TRIGGER_RISING, "AM300", par);
 245         if (ret)
 246                 dev_err(&am300_device->dev, "request_irq failed: %d\n", ret);
 247
 248         return ret;
 249 }
 250
 251 static struct broadsheet_board am300_board = {
 252         .owner                  = THIS_MODULE,
 253         .init                   = am300_init_board,
 254         .cleanup                = am300_cleanup,
 255         .set_hdb                = am300_set_hdb,
 256         .get_hdb                = am300_get_hdb,
 257         .set_ctl                = am300_set_ctl,
 258         .wait_for_rdy           = am300_wait_event,
 259         .get_panel_type         = am300_get_panel_type,
 260         .setup_irq              = am300_setup_irq,
 261 };
 262
 263 int __init am300_init(void)
 264 {
 265         int ret;
 266
 267         pxa2xx_mfp_config(ARRAY_AND_SIZE(am300_pin_config));
 268
 269         /* request our platform independent driver */
 270         request_module("broadsheetfb");
 271
 272         am300_device = platform_device_alloc("broadsheetfb", -1);
 273         if (!am300_device)
 274                 return -ENOMEM;
 275
 276         /* the am300_board that will be seen by broadsheetfb is a copy */
 277         platform_device_add_data(am300_device, &am300_board,
 278                                         sizeof(am300_board));
 279
 280         ret = platform_device_add(am300_device);
 281
 282         if (ret) {
 283                 platform_device_put(am300_device);
 284                 return ret;
 285         }
 286
 287         return 0;
 288 }
 289
 290 module_param(panel_type, uint, 0);
 291 MODULE_PARM_DESC(panel_type, "Select the panel type: 37, 6, 97");
 292
 293 MODULE_DESCRIPTION("board driver for am300 epd kit");
 294 MODULE_AUTHOR("Jaya Kumar");
 295 MODULE_LICENSE("GPL");