[ARM] 5281/1: pxa: split cm-x2xx.c to cm-x2xx.c and cm-x270.c
[deliverable/linux.git] / arch / arm / mach-pxa / cm-x2xx.c
1 /*
2 * linux/arch/arm/mach-pxa/cm-x2xx.c
3 *
4 * Copyright (C) 2008 CompuLab, Ltd.
5 * Mike Rapoport <mike@compulab.co.il>
6 *
7 * This program is free software; you can redistribute it and/or modify
8 * it under the terms of the GNU General Public License version 2 as
9 * published by the Free Software Foundation.
10 */
11
12 #include <linux/platform_device.h>
13 #include <linux/sysdev.h>
14 #include <linux/irq.h>
15 #include <linux/gpio.h>
16
17 #include <linux/dm9000.h>
18 #include <linux/leds.h>
19
20 #include <asm/mach/arch.h>
21 #include <asm/mach-types.h>
22 #include <asm/mach/map.h>
23
24 #include <mach/pxa2xx-regs.h>
25 #include <mach/mfp-pxa27x.h>
26 #include <mach/pxa-regs.h>
27 #include <mach/audio.h>
28 #include <mach/pxafb.h>
29
30 #include <asm/hardware/it8152.h>
31
32 #include "generic.h"
33 #include "cm-x2xx-pci.h"
34
35 extern void cmx270_init(void);
36
37 /* virtual addresses for statically mapped regions */
38 #define CMX2XX_VIRT_BASE (0xe8000000)
39 #define CMX2XX_IT8152_VIRT (CMX2XX_VIRT_BASE)
40
41 /* physical address if local-bus attached devices */
42 #define CMX270_DM9000_PHYS_BASE (PXA_CS1_PHYS + (6 << 22))
43
44 /* leds */
45 #define CMX270_GPIO_RED (93)
46 #define CMX270_GPIO_GREEN (94)
47
48 /* GPIO IRQ usage */
49 #define GPIO10_ETHIRQ (10)
50 #define CMX270_GPIO_IT8152_IRQ (22)
51
52 #define CMX270_ETHIRQ IRQ_GPIO(GPIO10_ETHIRQ)
53
54 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
55 static struct resource cmx270_dm9000_resource[] = {
56 [0] = {
57 .start = CMX270_DM9000_PHYS_BASE,
58 .end = CMX270_DM9000_PHYS_BASE + 3,
59 .flags = IORESOURCE_MEM,
60 },
61 [1] = {
62 .start = CMX270_DM9000_PHYS_BASE + 8,
63 .end = CMX270_DM9000_PHYS_BASE + 8 + 500,
64 .flags = IORESOURCE_MEM,
65 },
66 [2] = {
67 .start = CMX270_ETHIRQ,
68 .end = CMX270_ETHIRQ,
69 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
70 }
71 };
72
73 static struct dm9000_plat_data cmx270_dm9000_platdata = {
74 .flags = DM9000_PLATF_32BITONLY,
75 };
76
77 static struct platform_device cmx2xx_dm9000_device = {
78 .name = "dm9000",
79 .id = 0,
80 .num_resources = ARRAY_SIZE(cmx270_dm9000_resource),
81 .dev = {
82 .platform_data = &cmx270_dm9000_platdata,
83 }
84 };
85
86 static void __init cmx2xx_init_dm9000(void)
87 {
88 cmx2xx_dm9000_device.resource = cmx270_dm9000_resource,
89 platform_device_register(&cmx2xx_dm9000_device);
90 }
91 #else
92 static inline void cmx2xx_init_dm9000(void) {}
93 #endif
94
95 /* UCB1400 touchscreen controller */
96 #if defined(CONFIG_TOUCHSCREEN_UCB1400) || defined(CONFIG_TOUCHSCREEN_UCB1400_MODULE)
97 static struct platform_device cmx2xx_ts_device = {
98 .name = "ucb1400_ts",
99 .id = -1,
100 };
101
102 static void __init cmx2xx_init_touchscreen(void)
103 {
104 platform_device_register(&cmx2xx_ts_device);
105 }
106 #else
107 static inline void cmx2xx_init_touchscreen(void) {}
108 #endif
109
110 /* CM-X270 LEDs */
111 #if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
112 static struct gpio_led cmx2xx_leds[] = {
113 [0] = {
114 .name = "cm-x2xx:red",
115 .default_trigger = "nand-disk",
116 .active_low = 1,
117 },
118 [1] = {
119 .name = "cm-x2xx:green",
120 .default_trigger = "heartbeat",
121 .active_low = 1,
122 },
123 };
124
125 static struct gpio_led_platform_data cmx2xx_gpio_led_pdata = {
126 .num_leds = ARRAY_SIZE(cmx2xx_leds),
127 .leds = cmx2xx_leds,
128 };
129
130 static struct platform_device cmx2xx_led_device = {
131 .name = "leds-gpio",
132 .id = -1,
133 .dev = {
134 .platform_data = &cmx2xx_gpio_led_pdata,
135 },
136 };
137
138 static void __init cmx2xx_init_leds(void)
139 {
140 cmx2xx_leds[0].gpio = CMX270_GPIO_RED;
141 cmx2xx_leds[1].gpio = CMX270_GPIO_GREEN;
142 platform_device_register(&cmx2xx_led_device);
143 }
144 #else
145 static inline void cmx2xx_init_leds(void) {}
146 #endif
147
148 #if defined(CONFIG_FB_PXA) || defined(CONFIG_FB_PXA_MODULE)
149 /*
150 Display definitions
151 keep these for backwards compatibility, although symbolic names (as
152 e.g. in lpd270.c) looks better
153 */
154 #define MTYPE_STN320x240 0
155 #define MTYPE_TFT640x480 1
156 #define MTYPE_CRT640x480 2
157 #define MTYPE_CRT800x600 3
158 #define MTYPE_TFT320x240 6
159 #define MTYPE_STN640x480 7
160
161 static struct pxafb_mode_info generic_stn_320x240_mode = {
162 .pixclock = 76923,
163 .bpp = 8,
164 .xres = 320,
165 .yres = 240,
166 .hsync_len = 3,
167 .vsync_len = 2,
168 .left_margin = 3,
169 .upper_margin = 0,
170 .right_margin = 3,
171 .lower_margin = 0,
172 .sync = (FB_SYNC_HOR_HIGH_ACT |
173 FB_SYNC_VERT_HIGH_ACT),
174 .cmap_greyscale = 0,
175 };
176
177 static struct pxafb_mach_info generic_stn_320x240 = {
178 .modes = &generic_stn_320x240_mode,
179 .num_modes = 1,
180 .lccr0 = 0,
181 .lccr3 = (LCCR3_PixClkDiv(0x03) |
182 LCCR3_Acb(0xff) |
183 LCCR3_PCP),
184 .cmap_inverse = 0,
185 .cmap_static = 0,
186 };
187
188 static struct pxafb_mode_info generic_tft_640x480_mode = {
189 .pixclock = 38461,
190 .bpp = 8,
191 .xres = 640,
192 .yres = 480,
193 .hsync_len = 60,
194 .vsync_len = 2,
195 .left_margin = 70,
196 .upper_margin = 10,
197 .right_margin = 70,
198 .lower_margin = 5,
199 .sync = 0,
200 .cmap_greyscale = 0,
201 };
202
203 static struct pxafb_mach_info generic_tft_640x480 = {
204 .modes = &generic_tft_640x480_mode,
205 .num_modes = 1,
206 .lccr0 = (LCCR0_PAS),
207 .lccr3 = (LCCR3_PixClkDiv(0x01) |
208 LCCR3_Acb(0xff) |
209 LCCR3_PCP),
210 .cmap_inverse = 0,
211 .cmap_static = 0,
212 };
213
214 static struct pxafb_mode_info generic_crt_640x480_mode = {
215 .pixclock = 38461,
216 .bpp = 8,
217 .xres = 640,
218 .yres = 480,
219 .hsync_len = 63,
220 .vsync_len = 2,
221 .left_margin = 81,
222 .upper_margin = 33,
223 .right_margin = 16,
224 .lower_margin = 10,
225 .sync = (FB_SYNC_HOR_HIGH_ACT |
226 FB_SYNC_VERT_HIGH_ACT),
227 .cmap_greyscale = 0,
228 };
229
230 static struct pxafb_mach_info generic_crt_640x480 = {
231 .modes = &generic_crt_640x480_mode,
232 .num_modes = 1,
233 .lccr0 = (LCCR0_PAS),
234 .lccr3 = (LCCR3_PixClkDiv(0x01) |
235 LCCR3_Acb(0xff)),
236 .cmap_inverse = 0,
237 .cmap_static = 0,
238 };
239
240 static struct pxafb_mode_info generic_crt_800x600_mode = {
241 .pixclock = 28846,
242 .bpp = 8,
243 .xres = 800,
244 .yres = 600,
245 .hsync_len = 63,
246 .vsync_len = 2,
247 .left_margin = 26,
248 .upper_margin = 21,
249 .right_margin = 26,
250 .lower_margin = 11,
251 .sync = (FB_SYNC_HOR_HIGH_ACT |
252 FB_SYNC_VERT_HIGH_ACT),
253 .cmap_greyscale = 0,
254 };
255
256 static struct pxafb_mach_info generic_crt_800x600 = {
257 .modes = &generic_crt_800x600_mode,
258 .num_modes = 1,
259 .lccr0 = (LCCR0_PAS),
260 .lccr3 = (LCCR3_PixClkDiv(0x02) |
261 LCCR3_Acb(0xff)),
262 .cmap_inverse = 0,
263 .cmap_static = 0,
264 };
265
266 static struct pxafb_mode_info generic_tft_320x240_mode = {
267 .pixclock = 134615,
268 .bpp = 16,
269 .xres = 320,
270 .yres = 240,
271 .hsync_len = 63,
272 .vsync_len = 7,
273 .left_margin = 75,
274 .upper_margin = 0,
275 .right_margin = 15,
276 .lower_margin = 15,
277 .sync = 0,
278 .cmap_greyscale = 0,
279 };
280
281 static struct pxafb_mach_info generic_tft_320x240 = {
282 .modes = &generic_tft_320x240_mode,
283 .num_modes = 1,
284 .lccr0 = (LCCR0_PAS),
285 .lccr3 = (LCCR3_PixClkDiv(0x06) |
286 LCCR3_Acb(0xff) |
287 LCCR3_PCP),
288 .cmap_inverse = 0,
289 .cmap_static = 0,
290 };
291
292 static struct pxafb_mode_info generic_stn_640x480_mode = {
293 .pixclock = 57692,
294 .bpp = 8,
295 .xres = 640,
296 .yres = 480,
297 .hsync_len = 4,
298 .vsync_len = 2,
299 .left_margin = 10,
300 .upper_margin = 5,
301 .right_margin = 10,
302 .lower_margin = 5,
303 .sync = (FB_SYNC_HOR_HIGH_ACT |
304 FB_SYNC_VERT_HIGH_ACT),
305 .cmap_greyscale = 0,
306 };
307
308 static struct pxafb_mach_info generic_stn_640x480 = {
309 .modes = &generic_stn_640x480_mode,
310 .num_modes = 1,
311 .lccr0 = 0,
312 .lccr3 = (LCCR3_PixClkDiv(0x02) |
313 LCCR3_Acb(0xff)),
314 .cmap_inverse = 0,
315 .cmap_static = 0,
316 };
317
318 static struct pxafb_mach_info *cmx2xx_display = &generic_crt_640x480;
319
320 static int __init cmx2xx_set_display(char *str)
321 {
322 int disp_type = simple_strtol(str, NULL, 0);
323 switch (disp_type) {
324 case MTYPE_STN320x240:
325 cmx2xx_display = &generic_stn_320x240;
326 break;
327 case MTYPE_TFT640x480:
328 cmx2xx_display = &generic_tft_640x480;
329 break;
330 case MTYPE_CRT640x480:
331 cmx2xx_display = &generic_crt_640x480;
332 break;
333 case MTYPE_CRT800x600:
334 cmx2xx_display = &generic_crt_800x600;
335 break;
336 case MTYPE_TFT320x240:
337 cmx2xx_display = &generic_tft_320x240;
338 break;
339 case MTYPE_STN640x480:
340 cmx2xx_display = &generic_stn_640x480;
341 break;
342 default: /* fallback to CRT 640x480 */
343 cmx2xx_display = &generic_crt_640x480;
344 break;
345 }
346 return 1;
347 }
348
349 /*
350 This should be done really early to get proper configuration for
351 frame buffer.
352 Indeed, pxafb parameters can be used istead, but CM-X2XX bootloader
353 has limitied line length for kernel command line, and also it will
354 break compatibitlty with proprietary releases already in field.
355 */
356 __setup("monitor=", cmx2xx_set_display);
357
358 static void __init cmx2xx_init_display(void)
359 {
360 set_pxa_fb_info(cmx2xx_display);
361 }
362 #else
363 static inline void cmx2xx_init_display(void) {}
364 #endif
365
366 #ifdef CONFIG_PM
367 static unsigned long sleep_save_msc[10];
368
369 static int cmx2xx_suspend(struct sys_device *dev, pm_message_t state)
370 {
371 cmx2xx_pci_suspend();
372
373 /* save MSC registers */
374 sleep_save_msc[0] = MSC0;
375 sleep_save_msc[1] = MSC1;
376 sleep_save_msc[2] = MSC2;
377
378 /* setup power saving mode registers */
379 PCFR = 0x0;
380 PSLR = 0xff400000;
381 PMCR = 0x00000005;
382 PWER = 0x80000000;
383 PFER = 0x00000000;
384 PRER = 0x00000000;
385 PGSR0 = 0xC0018800;
386 PGSR1 = 0x004F0002;
387 PGSR2 = 0x6021C000;
388 PGSR3 = 0x00020000;
389
390 return 0;
391 }
392
393 static int cmx2xx_resume(struct sys_device *dev)
394 {
395 cmx2xx_pci_resume();
396
397 /* restore MSC registers */
398 MSC0 = sleep_save_msc[0];
399 MSC1 = sleep_save_msc[1];
400 MSC2 = sleep_save_msc[2];
401
402 return 0;
403 }
404
405 static struct sysdev_class cmx2xx_pm_sysclass = {
406 .name = "pm",
407 .resume = cmx2xx_resume,
408 .suspend = cmx2xx_suspend,
409 };
410
411 static struct sys_device cmx2xx_pm_device = {
412 .cls = &cmx2xx_pm_sysclass,
413 };
414
415 static int __init cmx2xx_pm_init(void)
416 {
417 int error;
418 error = sysdev_class_register(&cmx2xx_pm_sysclass);
419 if (error == 0)
420 error = sysdev_register(&cmx2xx_pm_device);
421 return error;
422 }
423 #else
424 static int __init cmx2xx_pm_init(void) { return 0; }
425 #endif
426
427 #if defined(CONFIG_SND_PXA2XX_AC97) || defined(CONFIG_SND_PXA2XX_AC97_MODULE)
428 static void __init cmx2xx_init_ac97(void)
429 {
430 pxa_set_ac97_info(NULL);
431 }
432 #else
433 static inline void cmx2xx_init_ac97(void) {}
434 #endif
435
436 static void __init cmx2xx_init(void)
437 {
438 cmx2xx_pm_init();
439
440 cmx270_init();
441
442 cmx2xx_init_dm9000();
443 cmx2xx_init_display();
444 cmx2xx_init_ac97();
445 cmx2xx_init_touchscreen();
446 cmx2xx_init_leds();
447 }
448
449 static void __init cmx2xx_init_irq(void)
450 {
451 pxa27x_init_irq();
452
453 cmx2xx_pci_init_irq(CMX270_GPIO_IT8152_IRQ);
454 }
455
456 #ifdef CONFIG_PCI
457 /* Map PCI companion statically */
458 static struct map_desc cmx2xx_io_desc[] __initdata = {
459 [0] = { /* PCI bridge */
460 .virtual = CMX2XX_IT8152_VIRT,
461 .pfn = __phys_to_pfn(PXA_CS4_PHYS),
462 .length = SZ_64M,
463 .type = MT_DEVICE
464 },
465 };
466
467 static void __init cmx2xx_map_io(void)
468 {
469 pxa_map_io();
470 iotable_init(cmx2xx_io_desc, ARRAY_SIZE(cmx2xx_io_desc));
471
472 it8152_base_address = CMX2XX_IT8152_VIRT;
473 }
474 #else
475 static void __init cmx2xx_map_io(void)
476 {
477 pxa_map_io();
478 }
479 #endif
480
481 MACHINE_START(ARMCORE, "Compulab CM-X2XX")
482 .boot_params = 0xa0000100,
483 .phys_io = 0x40000000,
484 .io_pg_offst = (io_p2v(0x40000000) >> 18) & 0xfffc,
485 .map_io = cmx2xx_map_io,
486 .init_irq = cmx2xx_init_irq,
487 .timer = &pxa_timer,
488 .init_machine = cmx2xx_init,
489 MACHINE_END
This page took 0.040761 seconds and 5 git commands to generate.