arm: Fold irq_set_chip/irq_set_handler
[deliverable/linux.git] / arch / arm / mach-pxa / lubbock.c
1 /*
2 * linux/arch/arm/mach-pxa/lubbock.c
3 *
4 * Support for the Intel DBPXA250 Development Platform.
5 *
6 * Author: Nicolas Pitre
7 * Created: Jun 15, 2001
8 * Copyright: MontaVista Software Inc.
9 *
10 * This program is free software; you can redistribute it and/or modify
11 * it under the terms of the GNU General Public License version 2 as
12 * published by the Free Software Foundation.
13 */
14 #include <linux/module.h>
15 #include <linux/kernel.h>
16 #include <linux/init.h>
17 #include <linux/platform_device.h>
18 #include <linux/sysdev.h>
19 #include <linux/major.h>
20 #include <linux/fb.h>
21 #include <linux/interrupt.h>
22 #include <linux/mtd/mtd.h>
23 #include <linux/mtd/partitions.h>
24 #include <linux/smc91x.h>
25
26 #include <linux/spi/spi.h>
27 #include <linux/spi/ads7846.h>
28 #include <linux/spi/pxa2xx_spi.h>
29
30 #include <asm/setup.h>
31 #include <asm/memory.h>
32 #include <asm/mach-types.h>
33 #include <mach/hardware.h>
34 #include <asm/irq.h>
35 #include <asm/sizes.h>
36
37 #include <asm/mach/arch.h>
38 #include <asm/mach/map.h>
39 #include <asm/mach/irq.h>
40 #include <asm/mach/flash.h>
41
42 #include <asm/hardware/sa1111.h>
43
44 #include <mach/pxa25x.h>
45 #include <mach/gpio.h>
46 #include <mach/audio.h>
47 #include <mach/lubbock.h>
48 #include <mach/udc.h>
49 #include <mach/irda.h>
50 #include <mach/pxafb.h>
51 #include <mach/mmc.h>
52 #include <mach/pm.h>
53 #include <mach/smemc.h>
54
55 #include "generic.h"
56 #include "clock.h"
57 #include "devices.h"
58
59 static unsigned long lubbock_pin_config[] __initdata = {
60 GPIO15_nCS_1, /* CS1 - Flash */
61 GPIO78_nCS_2, /* CS2 - Baseboard FGPA */
62 GPIO79_nCS_3, /* CS3 - SMC ethernet */
63 GPIO80_nCS_4, /* CS4 - SA1111 */
64
65 /* SSP data pins */
66 GPIO23_SSP1_SCLK,
67 GPIO25_SSP1_TXD,
68 GPIO26_SSP1_RXD,
69
70 /* AC97 */
71 GPIO28_AC97_BITCLK,
72 GPIO29_AC97_SDATA_IN_0,
73 GPIO30_AC97_SDATA_OUT,
74 GPIO31_AC97_SYNC,
75
76 /* LCD - 16bpp DSTN */
77 GPIOxx_LCD_DSTN_16BPP,
78
79 /* BTUART */
80 GPIO42_BTUART_RXD,
81 GPIO43_BTUART_TXD,
82 GPIO44_BTUART_CTS,
83 GPIO45_BTUART_RTS,
84
85 /* PC Card */
86 GPIO48_nPOE,
87 GPIO49_nPWE,
88 GPIO50_nPIOR,
89 GPIO51_nPIOW,
90 GPIO52_nPCE_1,
91 GPIO53_nPCE_2,
92 GPIO54_nPSKTSEL,
93 GPIO55_nPREG,
94 GPIO56_nPWAIT,
95 GPIO57_nIOIS16,
96
97 /* MMC */
98 GPIO6_MMC_CLK,
99 GPIO8_MMC_CS0,
100
101 /* wakeup */
102 GPIO1_GPIO | WAKEUP_ON_EDGE_RISE,
103 };
104
105 #define LUB_HEXLED __LUB_REG(LUBBOCK_FPGA_PHYS + 0x010)
106 #define LUB_MISC_WR __LUB_REG(LUBBOCK_FPGA_PHYS + 0x080)
107
108 void lubbock_set_hexled(uint32_t value)
109 {
110 LUB_HEXLED = value;
111 }
112
113 void lubbock_set_misc_wr(unsigned int mask, unsigned int set)
114 {
115 unsigned long flags;
116
117 local_irq_save(flags);
118 LUB_MISC_WR = (LUB_MISC_WR & ~mask) | (set & mask);
119 local_irq_restore(flags);
120 }
121 EXPORT_SYMBOL(lubbock_set_misc_wr);
122
123 static unsigned long lubbock_irq_enabled;
124
125 static void lubbock_mask_irq(struct irq_data *d)
126 {
127 int lubbock_irq = (d->irq - LUBBOCK_IRQ(0));
128 LUB_IRQ_MASK_EN = (lubbock_irq_enabled &= ~(1 << lubbock_irq));
129 }
130
131 static void lubbock_unmask_irq(struct irq_data *d)
132 {
133 int lubbock_irq = (d->irq - LUBBOCK_IRQ(0));
134 /* the irq can be acknowledged only if deasserted, so it's done here */
135 LUB_IRQ_SET_CLR &= ~(1 << lubbock_irq);
136 LUB_IRQ_MASK_EN = (lubbock_irq_enabled |= (1 << lubbock_irq));
137 }
138
139 static struct irq_chip lubbock_irq_chip = {
140 .name = "FPGA",
141 .irq_ack = lubbock_mask_irq,
142 .irq_mask = lubbock_mask_irq,
143 .irq_unmask = lubbock_unmask_irq,
144 };
145
146 static void lubbock_irq_handler(unsigned int irq, struct irq_desc *desc)
147 {
148 unsigned long pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
149 do {
150 /* clear our parent irq */
151 desc->irq_data.chip->irq_ack(&desc->irq_data);
152 if (likely(pending)) {
153 irq = LUBBOCK_IRQ(0) + __ffs(pending);
154 generic_handle_irq(irq);
155 }
156 pending = LUB_IRQ_SET_CLR & lubbock_irq_enabled;
157 } while (pending);
158 }
159
160 static void __init lubbock_init_irq(void)
161 {
162 int irq;
163
164 pxa25x_init_irq();
165
166 /* setup extra lubbock irqs */
167 for (irq = LUBBOCK_IRQ(0); irq <= LUBBOCK_LAST_IRQ; irq++) {
168 irq_set_chip_and_handler(irq, &lubbock_irq_chip,
169 handle_level_irq);
170 set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
171 }
172
173 irq_set_chained_handler(IRQ_GPIO(0), lubbock_irq_handler);
174 irq_set_irq_type(IRQ_GPIO(0), IRQ_TYPE_EDGE_FALLING);
175 }
176
177 #ifdef CONFIG_PM
178
179 static int lubbock_irq_resume(struct sys_device *dev)
180 {
181 LUB_IRQ_MASK_EN = lubbock_irq_enabled;
182 return 0;
183 }
184
185 static struct sysdev_class lubbock_irq_sysclass = {
186 .name = "cpld_irq",
187 .resume = lubbock_irq_resume,
188 };
189
190 static struct sys_device lubbock_irq_device = {
191 .cls = &lubbock_irq_sysclass,
192 };
193
194 static int __init lubbock_irq_device_init(void)
195 {
196 int ret = -ENODEV;
197
198 if (machine_is_lubbock()) {
199 ret = sysdev_class_register(&lubbock_irq_sysclass);
200 if (ret == 0)
201 ret = sysdev_register(&lubbock_irq_device);
202 }
203 return ret;
204 }
205
206 device_initcall(lubbock_irq_device_init);
207
208 #endif
209
210 static int lubbock_udc_is_connected(void)
211 {
212 return (LUB_MISC_RD & (1 << 9)) == 0;
213 }
214
215 static struct pxa2xx_udc_mach_info udc_info __initdata = {
216 .udc_is_connected = lubbock_udc_is_connected,
217 // no D+ pullup; lubbock can't connect/disconnect in software
218 };
219
220 static struct resource sa1111_resources[] = {
221 [0] = {
222 .start = 0x10000000,
223 .end = 0x10001fff,
224 .flags = IORESOURCE_MEM,
225 },
226 [1] = {
227 .start = LUBBOCK_SA1111_IRQ,
228 .end = LUBBOCK_SA1111_IRQ,
229 .flags = IORESOURCE_IRQ,
230 },
231 };
232
233 static struct sa1111_platform_data sa1111_info = {
234 .irq_base = LUBBOCK_SA1111_IRQ_BASE,
235 };
236
237 static struct platform_device sa1111_device = {
238 .name = "sa1111",
239 .id = -1,
240 .num_resources = ARRAY_SIZE(sa1111_resources),
241 .resource = sa1111_resources,
242 .dev = {
243 .platform_data = &sa1111_info,
244 },
245 };
246
247 /* ADS7846 is connected through SSP ... and if your board has J5 populated,
248 * you can select it to replace the ucb1400 by switching the touchscreen cable
249 * (to J5) and poking board registers (as done below). Else it's only useful
250 * for the temperature sensors.
251 */
252 static struct pxa2xx_spi_master pxa_ssp_master_info = {
253 .num_chipselect = 1,
254 };
255
256 static int lubbock_ads7846_pendown_state(void)
257 {
258 /* TS_BUSY is bit 8 in LUB_MISC_RD, but pendown is irq-only */
259 return 0;
260 }
261
262 static struct ads7846_platform_data ads_info = {
263 .model = 7846,
264 .vref_delay_usecs = 100, /* internal, no cap */
265 .get_pendown_state = lubbock_ads7846_pendown_state,
266 // .x_plate_ohms = 500, /* GUESS! */
267 // .y_plate_ohms = 500, /* GUESS! */
268 };
269
270 static void ads7846_cs(u32 command)
271 {
272 static const unsigned TS_nCS = 1 << 11;
273 lubbock_set_misc_wr(TS_nCS, (command == PXA2XX_CS_ASSERT) ? 0 : TS_nCS);
274 }
275
276 static struct pxa2xx_spi_chip ads_hw = {
277 .tx_threshold = 1,
278 .rx_threshold = 2,
279 .cs_control = ads7846_cs,
280 };
281
282 static struct spi_board_info spi_board_info[] __initdata = { {
283 .modalias = "ads7846",
284 .platform_data = &ads_info,
285 .controller_data = &ads_hw,
286 .irq = LUBBOCK_BB_IRQ,
287 .max_speed_hz = 120000 /* max sample rate at 3V */
288 * 26 /* command + data + overhead */,
289 .bus_num = 1,
290 .chip_select = 0,
291 },
292 };
293
294 static struct resource smc91x_resources[] = {
295 [0] = {
296 .name = "smc91x-regs",
297 .start = 0x0c000c00,
298 .end = 0x0c0fffff,
299 .flags = IORESOURCE_MEM,
300 },
301 [1] = {
302 .start = LUBBOCK_ETH_IRQ,
303 .end = LUBBOCK_ETH_IRQ,
304 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
305 },
306 [2] = {
307 .name = "smc91x-attrib",
308 .start = 0x0e000000,
309 .end = 0x0e0fffff,
310 .flags = IORESOURCE_MEM,
311 },
312 };
313
314 static struct smc91x_platdata lubbock_smc91x_info = {
315 .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT | SMC91X_IO_SHIFT_2,
316 };
317
318 static struct platform_device smc91x_device = {
319 .name = "smc91x",
320 .id = -1,
321 .num_resources = ARRAY_SIZE(smc91x_resources),
322 .resource = smc91x_resources,
323 .dev = {
324 .platform_data = &lubbock_smc91x_info,
325 },
326 };
327
328 static struct resource flash_resources[] = {
329 [0] = {
330 .start = 0x00000000,
331 .end = SZ_64M - 1,
332 .flags = IORESOURCE_MEM,
333 },
334 [1] = {
335 .start = 0x04000000,
336 .end = 0x04000000 + SZ_64M - 1,
337 .flags = IORESOURCE_MEM,
338 },
339 };
340
341 static struct mtd_partition lubbock_partitions[] = {
342 {
343 .name = "Bootloader",
344 .size = 0x00040000,
345 .offset = 0,
346 .mask_flags = MTD_WRITEABLE /* force read-only */
347 },{
348 .name = "Kernel",
349 .size = 0x00100000,
350 .offset = 0x00040000,
351 },{
352 .name = "Filesystem",
353 .size = MTDPART_SIZ_FULL,
354 .offset = 0x00140000
355 }
356 };
357
358 static struct flash_platform_data lubbock_flash_data[2] = {
359 {
360 .map_name = "cfi_probe",
361 .parts = lubbock_partitions,
362 .nr_parts = ARRAY_SIZE(lubbock_partitions),
363 }, {
364 .map_name = "cfi_probe",
365 .parts = NULL,
366 .nr_parts = 0,
367 }
368 };
369
370 static struct platform_device lubbock_flash_device[2] = {
371 {
372 .name = "pxa2xx-flash",
373 .id = 0,
374 .dev = {
375 .platform_data = &lubbock_flash_data[0],
376 },
377 .resource = &flash_resources[0],
378 .num_resources = 1,
379 },
380 {
381 .name = "pxa2xx-flash",
382 .id = 1,
383 .dev = {
384 .platform_data = &lubbock_flash_data[1],
385 },
386 .resource = &flash_resources[1],
387 .num_resources = 1,
388 },
389 };
390
391 static struct platform_device *devices[] __initdata = {
392 &sa1111_device,
393 &smc91x_device,
394 &lubbock_flash_device[0],
395 &lubbock_flash_device[1],
396 };
397
398 static struct pxafb_mode_info sharp_lm8v31_mode = {
399 .pixclock = 270000,
400 .xres = 640,
401 .yres = 480,
402 .bpp = 16,
403 .hsync_len = 1,
404 .left_margin = 3,
405 .right_margin = 3,
406 .vsync_len = 1,
407 .upper_margin = 0,
408 .lower_margin = 0,
409 .sync = FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
410 .cmap_greyscale = 0,
411 };
412
413 static struct pxafb_mach_info sharp_lm8v31 = {
414 .modes = &sharp_lm8v31_mode,
415 .num_modes = 1,
416 .cmap_inverse = 0,
417 .cmap_static = 0,
418 .lcd_conn = LCD_COLOR_DSTN_16BPP | LCD_PCLK_EDGE_FALL |
419 LCD_AC_BIAS_FREQ(255),
420 };
421
422 #define MMC_POLL_RATE msecs_to_jiffies(1000)
423
424 static void lubbock_mmc_poll(unsigned long);
425 static irq_handler_t mmc_detect_int;
426
427 static struct timer_list mmc_timer = {
428 .function = lubbock_mmc_poll,
429 };
430
431 static void lubbock_mmc_poll(unsigned long data)
432 {
433 unsigned long flags;
434
435 /* clear any previous irq state, then ... */
436 local_irq_save(flags);
437 LUB_IRQ_SET_CLR &= ~(1 << 0);
438 local_irq_restore(flags);
439
440 /* poll until mmc/sd card is removed */
441 if (LUB_IRQ_SET_CLR & (1 << 0))
442 mod_timer(&mmc_timer, jiffies + MMC_POLL_RATE);
443 else {
444 (void) mmc_detect_int(LUBBOCK_SD_IRQ, (void *)data);
445 enable_irq(LUBBOCK_SD_IRQ);
446 }
447 }
448
449 static irqreturn_t lubbock_detect_int(int irq, void *data)
450 {
451 /* IRQ is level triggered; disable, and poll for removal */
452 disable_irq(irq);
453 mod_timer(&mmc_timer, jiffies + MMC_POLL_RATE);
454
455 return mmc_detect_int(irq, data);
456 }
457
458 static int lubbock_mci_init(struct device *dev,
459 irq_handler_t detect_int,
460 void *data)
461 {
462 /* detect card insert/eject */
463 mmc_detect_int = detect_int;
464 init_timer(&mmc_timer);
465 mmc_timer.data = (unsigned long) data;
466 return request_irq(LUBBOCK_SD_IRQ, lubbock_detect_int,
467 IRQF_SAMPLE_RANDOM, "lubbock-sd-detect", data);
468 }
469
470 static int lubbock_mci_get_ro(struct device *dev)
471 {
472 return (LUB_MISC_RD & (1 << 2)) != 0;
473 }
474
475 static void lubbock_mci_exit(struct device *dev, void *data)
476 {
477 free_irq(LUBBOCK_SD_IRQ, data);
478 del_timer_sync(&mmc_timer);
479 }
480
481 static struct pxamci_platform_data lubbock_mci_platform_data = {
482 .ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
483 .detect_delay_ms = 10,
484 .init = lubbock_mci_init,
485 .get_ro = lubbock_mci_get_ro,
486 .exit = lubbock_mci_exit,
487 .gpio_card_detect = -1,
488 .gpio_card_ro = -1,
489 .gpio_power = -1,
490 };
491
492 static void lubbock_irda_transceiver_mode(struct device *dev, int mode)
493 {
494 unsigned long flags;
495
496 local_irq_save(flags);
497 if (mode & IR_SIRMODE) {
498 LUB_MISC_WR &= ~(1 << 4);
499 } else if (mode & IR_FIRMODE) {
500 LUB_MISC_WR |= 1 << 4;
501 }
502 pxa2xx_transceiver_mode(dev, mode);
503 local_irq_restore(flags);
504 }
505
506 static struct pxaficp_platform_data lubbock_ficp_platform_data = {
507 .gpio_pwdown = -1,
508 .transceiver_cap = IR_SIRMODE | IR_FIRMODE,
509 .transceiver_mode = lubbock_irda_transceiver_mode,
510 };
511
512 static void __init lubbock_init(void)
513 {
514 int flashboot = (LUB_CONF_SWITCHES & 1);
515
516 pxa2xx_mfp_config(ARRAY_AND_SIZE(lubbock_pin_config));
517
518 pxa_set_ffuart_info(NULL);
519 pxa_set_btuart_info(NULL);
520 pxa_set_stuart_info(NULL);
521
522 clk_add_alias("SA1111_CLK", NULL, "GPIO11_CLK", NULL);
523 pxa_set_udc_info(&udc_info);
524 set_pxa_fb_info(&sharp_lm8v31);
525 pxa_set_mci_info(&lubbock_mci_platform_data);
526 pxa_set_ficp_info(&lubbock_ficp_platform_data);
527 pxa_set_ac97_info(NULL);
528
529 lubbock_flash_data[0].width = lubbock_flash_data[1].width =
530 (__raw_readl(BOOT_DEF) & 1) ? 2 : 4;
531 /* Compensate for the nROMBT switch which swaps the flash banks */
532 printk(KERN_NOTICE "Lubbock configured to boot from %s (bank %d)\n",
533 flashboot?"Flash":"ROM", flashboot);
534
535 lubbock_flash_data[flashboot^1].name = "application-flash";
536 lubbock_flash_data[flashboot].name = "boot-rom";
537 (void) platform_add_devices(devices, ARRAY_SIZE(devices));
538
539 pxa2xx_set_spi_info(1, &pxa_ssp_master_info);
540 spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
541 }
542
543 static struct map_desc lubbock_io_desc[] __initdata = {
544 { /* CPLD */
545 .virtual = LUBBOCK_FPGA_VIRT,
546 .pfn = __phys_to_pfn(LUBBOCK_FPGA_PHYS),
547 .length = 0x00100000,
548 .type = MT_DEVICE
549 }
550 };
551
552 static void __init lubbock_map_io(void)
553 {
554 pxa25x_map_io();
555 iotable_init(lubbock_io_desc, ARRAY_SIZE(lubbock_io_desc));
556
557 PCFR |= PCFR_OPDE;
558 }
559
560 MACHINE_START(LUBBOCK, "Intel DBPXA250 Development Platform (aka Lubbock)")
561 /* Maintainer: MontaVista Software Inc. */
562 .map_io = lubbock_map_io,
563 .nr_irqs = LUBBOCK_NR_IRQS,
564 .init_irq = lubbock_init_irq,
565 .timer = &pxa_timer,
566 .init_machine = lubbock_init,
567 MACHINE_END
This page took 0.044634 seconds and 5 git commands to generate.