arch/arm/mach-s3c64xx/Kconfig

   1 # Copyright 2008 Openmoko, Inc.
   2 #       Simtec Electronics, Ben Dooks <ben@simtec.co.uk>
   3 #
   4 # Licensed under GPLv2
   5
   6 # temporary until we can eliminate all drivers using it.
   7 config PLAT_S3C64XX
   8         bool
   9         depends on ARCH_S3C64XX
  10         default y
  11         help
  12           Base platform code for any Samsung S3C64XX device
  13
  14
  15 # Configuration options for the S3C6410 CPU
  16
  17 config CPU_S3C6400
  18         bool
  19         help
  20           Enable S3C6400 CPU support
  21
  22 config CPU_S3C6410
  23         bool
  24         help
  25           Enable S3C6410 CPU support
  26
  27 config S3C64XX_DMA
  28         bool "S3C64XX DMA"
  29         select S3C_DMA
  30
  31 config S3C64XX_SETUP_SDHCI
  32         select S3C64XX_SETUP_SDHCI_GPIO
  33         bool
  34         help
  35           Internal configuration for default SDHCI setup for S3C6400 and
  36           S3C6410 SoCs.
  37
  38 config S3C64XX_DEV_ONENAND1
  39         bool
  40         help
  41           Compile in platform device definition for OneNAND1 controller
  42
  43 # platform specific device setup
  44
  45 config S3C64XX_SETUP_I2C0
  46         bool
  47         default y
  48         help
  49           Common setup code for i2c bus 0.
  50
  51           Note, currently since i2c0 is always compiled, this setup helper
  52           is always compiled with it.
  53
  54 config S3C64XX_SETUP_I2C1
  55         bool
  56         help
  57           Common setup code for i2c bus 1.
  58
  59 config S3C64XX_SETUP_FB_24BPP
  60         bool
  61         help
  62           Common setup code for S3C64XX with an 24bpp RGB display helper.
  63
  64 config S3C64XX_SETUP_SDHCI_GPIO
  65         bool
  66         help
  67           Common setup code for S3C64XX SDHCI GPIO configurations
  68
  69 # S36400 Macchine support
  70
  71 config MACH_SMDK6400
  72        bool "SMDK6400"
  73         select CPU_S3C6400
  74         select S3C_DEV_HSMMC
  75         select S3C_DEV_NAND
  76         select S3C64XX_SETUP_SDHCI
  77         help
  78           Machine support for the Samsung SMDK6400
  79
  80 # S3C6410 machine support
  81
  82 config MACH_ANW6410
  83         bool "A&W6410"
  84         select CPU_S3C6410
  85         select S3C_DEV_FB
  86         select S3C64XX_SETUP_FB_24BPP
  87         help
  88           Machine support for the A&W6410
  89
  90 config MACH_SMDK6410
  91         bool "SMDK6410"
  92         select CPU_S3C6410
  93         select SAMSUNG_DEV_ADC
  94         select S3C_DEV_HSMMC
  95         select S3C_DEV_HSMMC1
  96         select S3C_DEV_I2C1
  97         select S3C_DEV_FB
  98         select SAMSUNG_DEV_TS
  99         select S3C_DEV_USB_HOST
 100         select S3C_DEV_USB_HSOTG
 101         select S3C_DEV_WDT
 102         select HAVE_S3C2410_WATCHDOG
 103         select S3C64XX_SETUP_SDHCI
 104         select S3C64XX_SETUP_I2C1
 105         select S3C64XX_SETUP_FB_24BPP
 106         help
 107           Machine support for the Samsung SMDK6410
 108
 109 # At least some of the SMDK6410s were shipped with the card detect
 110 # for the MMC/SD slots connected to the same input. This means that
 111 # either the boards need to be altered to have channel0 to an alternate
 112 # configuration or that only one slot can be used.
 113
 114 choice
 115         prompt "SMDK6410 MMC/SD slot setup"
 116         depends on MACH_SMDK6410
 117
 118 config SMDK6410_SD_CH0
 119         bool "Use channel 0 only"
 120         depends on MACH_SMDK6410
 121         help
 122           Select CON7 (channel 0) as the MMC/SD slot, as
 123           at least some SMDK6410 boards come with the
 124           resistors fitted so that the card detects for
 125           channels 0 and 1 are the same.
 126
 127 config SMDK6410_SD_CH1
 128         bool "Use channel 1 only"
 129         depends on MACH_SMDK6410
 130         help
 131           Select CON6 (channel 1) as the MMC/SD slot, as
 132           at least some SMDK6410 boards come with the
 133           resistors fitted so that the card detects for
 134           channels 0 and 1 are the same.
 135
 136 endchoice
 137
 138 config SMDK6410_WM1190_EV1
 139         bool "Support Wolfson Microelectronics 1190-EV1 PMIC card"
 140         depends on MACH_SMDK6410
 141         select REGULATOR
 142         select REGULATOR_WM8350
 143         select S3C24XX_GPIO_EXTRA64
 144         select MFD_WM8350_I2C
 145         select MFD_WM8350_CONFIG_MODE_0
 146         select MFD_WM8350_CONFIG_MODE_3
 147         select MFD_WM8352_CONFIG_MODE_0
 148         help
 149           The Wolfson Microelectronics 1190-EV1 is a WM835x based PMIC
 150           and audio daughtercard for the Samsung SMDK6410 reference
 151           platform.  Enabling this option will build support for this
 152           module into the kernel.  The presence of the module will be
 153           detected at runtime so the the resulting kernel can be used
 154           with or without the 1190-EV1 fitted.
 155
 156 config SMDK6410_WM1192_EV1
 157         bool "Support Wolfson Microelectronics 1192-EV1 PMIC card"
 158         depends on MACH_SMDK6410
 159         select REGULATOR
 160         select REGULATOR_WM831X
 161         select S3C24XX_GPIO_EXTRA64
 162         select MFD_WM831X
 163         help
 164           The Wolfson Microelectronics 1192-EV1 is a WM831x based PMIC
 165           daughtercard for the Samsung SMDK6410 reference platform.
 166           Enabling this option will build support for this module into
 167           the kernel.  The presence of the daughtercard will be
 168           detected at runtime so the the resulting kernel can be used
 169           with or without the 1192-EV1 fitted.
 170
 171 config MACH_NCP
 172         bool "NCP"
 173         select CPU_S3C6410
 174         select S3C_DEV_I2C1
 175         select S3C_DEV_HSMMC1
 176         select S3C64XX_SETUP_I2C1
 177         help
 178           Machine support for the Samsung NCP
 179
 180 config MACH_HMT
 181         bool "Airgoo HMT"
 182         select CPU_S3C6410
 183         select S3C_DEV_FB
 184         select S3C_DEV_NAND
 185         select S3C_DEV_USB_HOST
 186         select S3C64XX_SETUP_FB_24BPP
 187         select HAVE_PWM
 188         help
 189           Machine support for the Airgoo HMT
 190
 191 config MACH_SMARTQ
 192         bool
 193         select CPU_S3C6410
 194         select S3C_DEV_HSMMC
 195         select S3C_DEV_HSMMC1
 196         select S3C_DEV_HSMMC2
 197         select S3C_DEV_FB
 198         select S3C_DEV_HWMON
 199         select S3C_DEV_RTC
 200         select S3C_DEV_USB_HSOTG
 201         select S3C_DEV_USB_HOST
 202         select S3C64XX_SETUP_SDHCI
 203         select S3C64XX_SETUP_FB_24BPP
 204         select SAMSUNG_DEV_ADC
 205         select SAMSUNG_DEV_TS
 206         select HAVE_PWM
 207         help
 208             Shared machine support for SmartQ 5/7
 209
 210 config MACH_SMARTQ5
 211         bool "SmartQ 5"
 212         select MACH_SMARTQ
 213         help
 214             Machine support for the SmartQ 5
 215
 216 config MACH_SMARTQ7
 217         bool "SmartQ 7"
 218         select MACH_SMARTQ
 219         help
 220             Machine support for the SmartQ 7