arch/avr32/boards/atstk1000/Kconfig

   1 # STK1000 customization
   2
   3 if BOARD_ATSTK1002
   4
   5 config BOARD_ATSTK1002_CUSTOM
   6         bool "Non-default STK-1002 jumper settings"
   7         help
   8           You will normally leave the jumpers on the CPU card at their
   9           default settings.  If you need to use certain peripherals,
  10           you will need to change some of those jumpers.
  11
  12 if BOARD_ATSTK1002_CUSTOM
  13
  14 config BOARD_ATSTK1002_SW1_CUSTOM
  15         bool "SW1: use SSC1 (not SPI0)"
  16         help
  17           This also prevents using the external DAC as an audio interface,
  18           and means you can't initialize the on-board QVGA display.
  19
  20 config BOARD_ATSTK1002_SW2_CUSTOM
  21         bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)"
  22         help
  23           If you change this you'll want an updated boot loader putting
  24           the console on UART-C not UART-A.
  25
  26 config BOARD_ATSTK1002_SW3_CUSTOM
  27         bool "SW3: use TIMER1 (not SSC0 and GCLK)"
  28         help
  29           This also prevents using the external DAC as an audio interface.
  30
  31 config BOARD_ATSTK1002_SW4_CUSTOM
  32         bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)"
  33         help
  34           To use the camera interface you'll need a custom card (on the
  35           PCI-format connector) connect a video sensor.
  36
  37 config BOARD_ATSTK1002_SW5_CUSTOM
  38         bool "SW5: use MACB1 (not LCDC)"
  39
  40 config BOARD_ATSTK1002_SW6_CUSTOM
  41         bool "SW6: more GPIOs (not MACB0)"
  42
  43 endif   # custom
  44
  45 config BOARD_ATSTK1002_SPI1
  46         bool "Configure SPI1 controller"
  47         depends on !BOARD_ATSTK1002_SW4_CUSTOM
  48         help
  49           All the signals for the second SPI controller are available on
  50           GPIO lines and accessed through the J1 jumper block.  Say "y"
  51           here to configure that SPI controller.
  52
  53 config BOARD_ATSTK1002_J2_LED
  54         bool
  55         default BOARD_ATSTK1002_J2_LED8 || BOARD_ATSTK1002_J2_RGB
  56
  57 choice
  58         prompt "LEDs connected to J2:"
  59         depends on LEDS_GPIO && !BOARD_ATSTK1002_SW4_CUSTOM
  60         optional
  61         help
  62           Select this if you have jumpered the J2 jumper block to the
  63           LED0..LED7 amber leds, or to the RGB leds, using a ten-pin
  64           IDC cable.  A default "heartbeat" trigger is provided, but
  65           you can of course override this.
  66
  67 config BOARD_ATSTK1002_J2_LED8
  68         bool "LED0..LED7"
  69         help
  70           Select this if J2 is jumpered to LED0..LED7 amber leds.
  71
  72 config BOARD_ATSTK1002_J2_RGB
  73         bool "RGB leds"
  74         help
  75           Select this if J2 is jumpered to the RGB leds.
  76
  77 endchoice
  78
  79 endif   # stk 1002