arch/avr32/boards/atstk1000/Kconfig

   1 # STK1000 customization
   2
   3 if BOARD_ATSTK1000
   4
   5 choice
   6         prompt "ATSTK1000 CPU daughterboard type"
   7         default BOARD_ATSTK1002
   8
   9 config BOARD_ATSTK1002
  10         bool "ATSTK1002"
  11         select CPU_AT32AP7000
  12
  13 config BOARD_ATSTK1003
  14         bool "ATSTK1003"
  15         select CPU_AT32AP7001
  16
  17 config BOARD_ATSTK1004
  18         bool "ATSTK1004"
  19         select CPU_AT32AP7002
  20
  21 endchoice
  22
  23
  24 config BOARD_ATSTK100X_CUSTOM
  25         bool "Non-default STK1002/STK1003/STK1004 jumper settings"
  26         help
  27           You will normally leave the jumpers on the CPU card at their
  28           default settings.  If you need to use certain peripherals,
  29           you will need to change some of those jumpers.
  30
  31 if BOARD_ATSTK100X_CUSTOM
  32
  33 config BOARD_ATSTK100X_SW1_CUSTOM
  34         bool "SW1: use SSC1 (not SPI0)"
  35         help
  36           This also prevents using the external DAC as an audio interface,
  37           and means you can't initialize the on-board QVGA display.
  38
  39 config BOARD_ATSTK100X_SW2_CUSTOM
  40         bool "SW2: use IRDA or TIMER0 (not UART-A, MMC/SD, and PS2-A)"
  41         help
  42           If you change this you'll want an updated boot loader putting
  43           the console on UART-C not UART-A.
  44
  45 config BOARD_ATSTK100X_SW3_CUSTOM
  46         bool "SW3: use TIMER1 (not SSC0 and GCLK)"
  47         help
  48           This also prevents using the external DAC as an audio interface.
  49
  50 config BOARD_ATSTK100X_SW4_CUSTOM
  51         bool "SW4: use ISI/Camera (not GPIOs, SPI1, and PS2-B)"
  52         help
  53           To use the camera interface you'll need a custom card (on the
  54           PCI-format connector) connect a video sensor.
  55
  56 config BOARD_ATSTK1002_SW5_CUSTOM
  57         bool "SW5: use MACB1 (not LCDC)"
  58         depends on BOARD_ATSTK1002
  59
  60 config BOARD_ATSTK1002_SW6_CUSTOM
  61         bool "SW6: more GPIOs (not MACB0)"
  62         depends on BOARD_ATSTK1002
  63
  64 endif   # custom
  65
  66 config BOARD_ATSTK100X_SPI1
  67         bool "Configure SPI1 controller"
  68         depends on !BOARD_ATSTK100X_SW4_CUSTOM
  69         help
  70           All the signals for the second SPI controller are available on
  71           GPIO lines and accessed through the J1 jumper block.  Say "y"
  72           here to configure that SPI controller.
  73
  74 config BOARD_ATSTK1000_J2_LED
  75         bool
  76         default BOARD_ATSTK1000_J2_LED8 || BOARD_ATSTK1000_J2_RGB
  77
  78 choice
  79         prompt "LEDs connected to J2:"
  80         depends on LEDS_GPIO && !BOARD_ATSTK100X_SW4_CUSTOM
  81         optional
  82         help
  83           Select this if you have jumpered the J2 jumper block to the
  84           LED0..LED7 amber leds, or to the RGB leds, using a ten-pin
  85           IDC cable.  A default "heartbeat" trigger is provided, but
  86           you can of course override this.
  87
  88 config BOARD_ATSTK1000_J2_LED8
  89         bool "LED0..LED7"
  90         help
  91           Select this if J2 is jumpered to LED0..LED7 amber leds.
  92
  93 config BOARD_ATSTK1000_J2_RGB
  94         bool "RGB leds"
  95         help
  96           Select this if J2 is jumpered to the RGB leds.
  97
  98 endchoice
  99
 100 config BOARD_ATSTK1000_EXTDAC
 101         bool
 102         depends on !BOARD_ATSTK100X_SW1_CUSTOM && !BOARD_ATSTK100X_SW3_CUSTOM
 103         default y
 104
 105 endif   # stk 1000