arch/blackfin/mach-bf527/boards/ezkit.c

   1 /*
   2  * File:         arch/blackfin/mach-bf527/boards/ezkit.c
   3  * Based on:     arch/blackfin/mach-bf537/boards/stamp.c
   4  * Author:       Aidan Williams <aidan@nicta.com.au>
   5  *
   6  * Created:
   7  * Description:
   8  *
   9  * Modified:
  10  *               Copyright 2005 National ICT Australia (NICTA)
  11  *               Copyright 2004-2008 Analog Devices Inc.
  12  *
  13  * Bugs:         Enter bugs at http://blackfin.uclinux.org/
  14  *
  15  * This program is free software; you can redistribute it and/or modify
  16  * it under the terms of the GNU General Public License as published by
  17  * the Free Software Foundation; either version 2 of the License, or
  18  * (at your option) any later version.
  19  *
  20  * This program is distributed in the hope that it will be useful,
  21  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  22  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  23  * GNU General Public License for more details.
  24  *
  25  * You should have received a copy of the GNU General Public License
  26  * along with this program; if not, see the file COPYING, or write
  27  * to the Free Software Foundation, Inc.,
  28  * 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
  29  */
  30
  31 #include <linux/device.h>
  32 #include <linux/platform_device.h>
  33 #include <linux/mtd/mtd.h>
  34 #include <linux/mtd/partitions.h>
  35 #include <linux/mtd/physmap.h>
  36 #include <linux/spi/spi.h>
  37 #include <linux/spi/flash.h>
  38 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
  39 #include <linux/usb/isp1362.h>
  40 #endif
  41 #include <linux/i2c.h>
  42 #include <linux/irq.h>
  43 #include <linux/interrupt.h>
  44 #include <linux/usb/sl811.h>
  45 #include <linux/usb/musb.h>
  46 #include <asm/dma.h>
  47 #include <asm/bfin5xx_spi.h>
  48 #include <asm/reboot.h>
  49 #include <asm/nand.h>
  50 #include <asm/portmux.h>
  51 #include <asm/dpmc.h>
  52 #include <linux/spi/ad7877.h>
  53
  54 /*
  55  * Name the Board for the /proc/cpuinfo
  56  */
  57 const char bfin_board_name[] = "ADI BF527-EZKIT";
  58
  59 /*
  60  *  Driver needs to know address, irq and flag pin.
  61  */
  62
  63 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
  64 #include <linux/usb/isp1760.h>
  65 static struct resource bfin_isp1760_resources[] = {
  66         [0] = {
  67                 .start  = 0x203C0000,
  68                 .end    = 0x203C0000 + 0x000fffff,
  69                 .flags  = IORESOURCE_MEM,
  70         },
  71         [1] = {
  72                 .start  = IRQ_PF7,
  73                 .end    = IRQ_PF7,
  74                 .flags  = IORESOURCE_IRQ,
  75         },
  76 };
  77
  78 static struct isp1760_platform_data isp1760_priv = {
  79         .is_isp1761 = 0,
  80         .bus_width_16 = 1,
  81         .port1_otg = 0,
  82         .analog_oc = 0,
  83         .dack_polarity_high = 0,
  84         .dreq_polarity_high = 0,
  85 };
  86
  87 static struct platform_device bfin_isp1760_device = {
  88         .name           = "isp1760-hcd",
  89         .id             = 0,
  90         .dev = {
  91                 .platform_data = &isp1760_priv,
  92         },
  93         .num_resources  = ARRAY_SIZE(bfin_isp1760_resources),
  94         .resource       = bfin_isp1760_resources,
  95 };
  96 #endif
  97
  98 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
  99 static struct resource musb_resources[] = {
 100         [0] = {
 101                 .start  = 0xffc03800,
 102                 .end    = 0xffc03cff,
 103                 .flags  = IORESOURCE_MEM,
 104         },
 105         [1] = { /* general IRQ */
 106                 .start  = IRQ_USB_INT0,
 107                 .end    = IRQ_USB_INT0,
 108                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 109         },
 110         [2] = { /* DMA IRQ */
 111                 .start  = IRQ_USB_DMA,
 112                 .end    = IRQ_USB_DMA,
 113                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 114         },
 115 };
 116
 117 static struct musb_hdrc_config musb_config = {
 118         .multipoint     = 0,
 119         .dyn_fifo       = 0,
 120         .soft_con       = 1,
 121         .dma            = 1,
 122         .num_eps        = 8,
 123         .dma_channels   = 8,
 124         .gpio_vrsel     = GPIO_PG13,
 125 };
 126
 127 static struct musb_hdrc_platform_data musb_plat = {
 128 #if defined(CONFIG_USB_MUSB_OTG)
 129         .mode           = MUSB_OTG,
 130 #elif defined(CONFIG_USB_MUSB_HDRC_HCD)
 131         .mode           = MUSB_HOST,
 132 #elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
 133         .mode           = MUSB_PERIPHERAL,
 134 #endif
 135         .config         = &musb_config,
 136 };
 137
 138 static u64 musb_dmamask = ~(u32)0;
 139
 140 static struct platform_device musb_device = {
 141         .name           = "musb_hdrc",
 142         .id             = 0,
 143         .dev = {
 144                 .dma_mask               = &musb_dmamask,
 145                 .coherent_dma_mask      = 0xffffffff,
 146                 .platform_data          = &musb_plat,
 147         },
 148         .num_resources  = ARRAY_SIZE(musb_resources),
 149         .resource       = musb_resources,
 150 };
 151 #endif
 152
 153 #if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
 154
 155 static struct resource bf52x_t350mcqb_resources[] = {
 156         {
 157                 .start = IRQ_PPI_ERROR,
 158                 .end = IRQ_PPI_ERROR,
 159                 .flags = IORESOURCE_IRQ,
 160         },
 161 };
 162
 163 static struct platform_device bf52x_t350mcqb_device = {
 164         .name           = "bfin-t350mcqb",
 165         .id             = -1,
 166         .num_resources  = ARRAY_SIZE(bf52x_t350mcqb_resources),
 167         .resource       = bf52x_t350mcqb_resources,
 168 };
 169 #endif
 170
 171 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 172 static struct mtd_partition ezkit_partitions[] = {
 173         {
 174                 .name       = "bootloader(nor)",
 175                 .size       = 0x40000,
 176                 .offset     = 0,
 177         }, {
 178                 .name       = "linux kernel(nor)",
 179                 .size       = 0x1C0000,
 180                 .offset     = MTDPART_OFS_APPEND,
 181         }, {
 182                 .name       = "file system(nor)",
 183                 .size       = MTDPART_SIZ_FULL,
 184                 .offset     = MTDPART_OFS_APPEND,
 185         }
 186 };
 187
 188 static struct physmap_flash_data ezkit_flash_data = {
 189         .width      = 2,
 190         .parts      = ezkit_partitions,
 191         .nr_parts   = ARRAY_SIZE(ezkit_partitions),
 192 };
 193
 194 static struct resource ezkit_flash_resource = {
 195         .start = 0x20000000,
 196         .end   = 0x203fffff,
 197         .flags = IORESOURCE_MEM,
 198 };
 199
 200 static struct platform_device ezkit_flash_device = {
 201         .name          = "physmap-flash",
 202         .id            = 0,
 203         .dev = {
 204                 .platform_data = &ezkit_flash_data,
 205         },
 206         .num_resources = 1,
 207         .resource      = &ezkit_flash_resource,
 208 };
 209 #endif
 210
 211 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
 212 static struct mtd_partition partition_info[] = {
 213         {
 214                 .name = "linux kernel(nand)",
 215                 .offset = 0,
 216                 .size = 4 * 1024 * 1024,
 217         },
 218         {
 219                 .name = "file system(nand)",
 220                 .offset = MTDPART_OFS_APPEND,
 221                 .size = MTDPART_SIZ_FULL,
 222         },
 223 };
 224
 225 static struct bf5xx_nand_platform bf5xx_nand_platform = {
 226         .page_size = NFC_PG_SIZE_256,
 227         .data_width = NFC_NWIDTH_8,
 228         .partitions = partition_info,
 229         .nr_partitions = ARRAY_SIZE(partition_info),
 230         .rd_dly = 3,
 231         .wr_dly = 3,
 232 };
 233
 234 static struct resource bf5xx_nand_resources[] = {
 235         {
 236                 .start = NFC_CTL,
 237                 .end = NFC_DATA_RD + 2,
 238                 .flags = IORESOURCE_MEM,
 239         },
 240         {
 241                 .start = CH_NFC,
 242                 .end = CH_NFC,
 243                 .flags = IORESOURCE_IRQ,
 244         },
 245 };
 246
 247 static struct platform_device bf5xx_nand_device = {
 248         .name = "bf5xx-nand",
 249         .id = 0,
 250         .num_resources = ARRAY_SIZE(bf5xx_nand_resources),
 251         .resource = bf5xx_nand_resources,
 252         .dev = {
 253                 .platform_data = &bf5xx_nand_platform,
 254         },
 255 };
 256 #endif
 257
 258 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
 259 static struct resource bfin_pcmcia_cf_resources[] = {
 260         {
 261                 .start = 0x20310000, /* IO PORT */
 262                 .end = 0x20312000,
 263                 .flags = IORESOURCE_MEM,
 264         }, {
 265                 .start = 0x20311000, /* Attribute Memory */
 266                 .end = 0x20311FFF,
 267                 .flags = IORESOURCE_MEM,
 268         }, {
 269                 .start = IRQ_PF4,
 270                 .end = IRQ_PF4,
 271                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
 272         }, {
 273                 .start = 6, /* Card Detect PF6 */
 274                 .end = 6,
 275                 .flags = IORESOURCE_IRQ,
 276         },
 277 };
 278
 279 static struct platform_device bfin_pcmcia_cf_device = {
 280         .name = "bfin_cf_pcmcia",
 281         .id = -1,
 282         .num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources),
 283         .resource = bfin_pcmcia_cf_resources,
 284 };
 285 #endif
 286
 287 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 288 static struct platform_device rtc_device = {
 289         .name = "rtc-bfin",
 290         .id   = -1,
 291 };
 292 #endif
 293
 294 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 295 #include <linux/smc91x.h>
 296
 297 static struct smc91x_platdata smc91x_info = {
 298         .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 299         .leda = RPC_LED_100_10,
 300         .ledb = RPC_LED_TX_RX,
 301 };
 302
 303 static struct resource smc91x_resources[] = {
 304         {
 305                 .name = "smc91x-regs",
 306                 .start = 0x20300300,
 307                 .end = 0x20300300 + 16,
 308                 .flags = IORESOURCE_MEM,
 309         }, {
 310
 311                 .start = IRQ_PF7,
 312                 .end = IRQ_PF7,
 313                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 314         },
 315 };
 316 static struct platform_device smc91x_device = {
 317         .name = "smc91x",
 318         .id = 0,
 319         .num_resources = ARRAY_SIZE(smc91x_resources),
 320         .resource = smc91x_resources,
 321         .dev    = {
 322                 .platform_data  = &smc91x_info,
 323         },
 324 };
 325 #endif
 326
 327 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
 328 static struct resource dm9000_resources[] = {
 329         [0] = {
 330                 .start  = 0x203FB800,
 331                 .end    = 0x203FB800 + 1,
 332                 .flags  = IORESOURCE_MEM,
 333         },
 334         [1] = {
 335                 .start  = 0x203FB800 + 4,
 336                 .end    = 0x203FB800 + 5,
 337                 .flags  = IORESOURCE_MEM,
 338         },
 339         [2] = {
 340                 .start  = IRQ_PF9,
 341                 .end    = IRQ_PF9,
 342                 .flags  = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
 343         },
 344 };
 345
 346 static struct platform_device dm9000_device = {
 347         .name           = "dm9000",
 348         .id             = -1,
 349         .num_resources  = ARRAY_SIZE(dm9000_resources),
 350         .resource       = dm9000_resources,
 351 };
 352 #endif
 353
 354 #if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
 355 static struct resource sl811_hcd_resources[] = {
 356         {
 357                 .start = 0x20340000,
 358                 .end = 0x20340000,
 359                 .flags = IORESOURCE_MEM,
 360         }, {
 361                 .start = 0x20340004,
 362                 .end = 0x20340004,
 363                 .flags = IORESOURCE_MEM,
 364         }, {
 365                 .start = CONFIG_USB_SL811_BFIN_IRQ,
 366                 .end = CONFIG_USB_SL811_BFIN_IRQ,
 367                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 368         },
 369 };
 370
 371 #if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
 372 void sl811_port_power(struct device *dev, int is_on)
 373 {
 374         gpio_request(CONFIG_USB_SL811_BFIN_GPIO_VBUS, "usb:SL811_VBUS");
 375         gpio_direction_output(CONFIG_USB_SL811_BFIN_GPIO_VBUS, is_on);
 376 }
 377 #endif
 378
 379 static struct sl811_platform_data sl811_priv = {
 380         .potpg = 10,
 381         .power = 250,       /* == 500mA */
 382 #if defined(CONFIG_USB_SL811_BFIN_USE_VBUS)
 383         .port_power = &sl811_port_power,
 384 #endif
 385 };
 386
 387 static struct platform_device sl811_hcd_device = {
 388         .name = "sl811-hcd",
 389         .id = 0,
 390         .dev = {
 391                 .platform_data = &sl811_priv,
 392         },
 393         .num_resources = ARRAY_SIZE(sl811_hcd_resources),
 394         .resource = sl811_hcd_resources,
 395 };
 396 #endif
 397
 398 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 399 static struct resource isp1362_hcd_resources[] = {
 400         {
 401                 .start = 0x20360000,
 402                 .end = 0x20360000,
 403                 .flags = IORESOURCE_MEM,
 404         }, {
 405                 .start = 0x20360004,
 406                 .end = 0x20360004,
 407                 .flags = IORESOURCE_MEM,
 408         }, {
 409                 .start = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
 410                 .end = CONFIG_USB_ISP1362_BFIN_GPIO_IRQ,
 411                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 412         },
 413 };
 414
 415 static struct isp1362_platform_data isp1362_priv = {
 416         .sel15Kres = 1,
 417         .clknotstop = 0,
 418         .oc_enable = 0,
 419         .int_act_high = 0,
 420         .int_edge_triggered = 0,
 421         .remote_wakeup_connected = 0,
 422         .no_power_switching = 1,
 423         .power_switching_mode = 0,
 424 };
 425
 426 static struct platform_device isp1362_hcd_device = {
 427         .name = "isp1362-hcd",
 428         .id = 0,
 429         .dev = {
 430                 .platform_data = &isp1362_priv,
 431         },
 432         .num_resources = ARRAY_SIZE(isp1362_hcd_resources),
 433         .resource = isp1362_hcd_resources,
 434 };
 435 #endif
 436
 437 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 438 static struct platform_device bfin_mii_bus = {
 439         .name = "bfin_mii_bus",
 440 };
 441
 442 static struct platform_device bfin_mac_device = {
 443         .name = "bfin_mac",
 444         .dev.platform_data = &bfin_mii_bus,
 445 };
 446 #endif
 447
 448 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 449 static struct resource net2272_bfin_resources[] = {
 450         {
 451                 .start = 0x20300000,
 452                 .end = 0x20300000 + 0x100,
 453                 .flags = IORESOURCE_MEM,
 454         }, {
 455                 .start = IRQ_PF7,
 456                 .end = IRQ_PF7,
 457                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 458         },
 459 };
 460
 461 static struct platform_device net2272_bfin_device = {
 462         .name = "net2272",
 463         .id = -1,
 464         .num_resources = ARRAY_SIZE(net2272_bfin_resources),
 465         .resource = net2272_bfin_resources,
 466 };
 467 #endif
 468
 469 #if defined(CONFIG_MTD_M25P80) \
 470         || defined(CONFIG_MTD_M25P80_MODULE)
 471 static struct mtd_partition bfin_spi_flash_partitions[] = {
 472         {
 473                 .name = "bootloader(spi)",
 474                 .size = 0x00040000,
 475                 .offset = 0,
 476                 .mask_flags = MTD_CAP_ROM
 477         }, {
 478                 .name = "linux kernel(spi)",
 479                 .size = MTDPART_SIZ_FULL,
 480                 .offset = MTDPART_OFS_APPEND,
 481         }
 482 };
 483
 484 static struct flash_platform_data bfin_spi_flash_data = {
 485         .name = "m25p80",
 486         .parts = bfin_spi_flash_partitions,
 487         .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
 488         .type = "m25p16",
 489 };
 490
 491 /* SPI flash chip (m25p64) */
 492 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 493         .enable_dma = 0,         /* use dma transfer with this chip*/
 494         .bits_per_word = 8,
 495 };
 496 #endif
 497
 498 #if defined(CONFIG_BFIN_SPI_ADC) \
 499         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 500 /* SPI ADC chip */
 501 static struct bfin5xx_spi_chip spi_adc_chip_info = {
 502         .enable_dma = 1,         /* use dma transfer with this chip*/
 503         .bits_per_word = 16,
 504 };
 505 #endif
 506
 507 #if defined(CONFIG_SND_BLACKFIN_AD1836) \
 508         || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 509 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 510         .enable_dma = 0,
 511         .bits_per_word = 16,
 512 };
 513 #endif
 514
 515 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 516 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 517         .enable_dma = 0,
 518         .bits_per_word = 8,
 519 };
 520 #endif
 521
 522 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 523 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 524         .enable_dma = 0,
 525         .bits_per_word = 16,
 526 };
 527
 528 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 529         .model                  = 7877,
 530         .vref_delay_usecs       = 50,   /* internal, no capacitor */
 531         .x_plate_ohms           = 419,
 532         .y_plate_ohms           = 486,
 533         .pressure_max           = 1000,
 534         .pressure_min           = 0,
 535         .stopacq_polarity       = 1,
 536         .first_conversion_delay = 3,
 537         .acquisition_time       = 1,
 538         .averaging              = 1,
 539         .pen_down_acc_interval  = 1,
 540 };
 541 #endif
 542
 543 #if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
 544 #include <linux/spi/ad7879.h>
 545 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 546         .model                  = 7879, /* Model = AD7879 */
 547         .x_plate_ohms           = 620,  /* 620 Ohm from the touch datasheet */
 548         .pressure_max           = 10000,
 549         .pressure_min           = 0,
 550         .first_conversion_delay = 3,    /* wait 512us before do a first conversion */
 551         .acquisition_time       = 1,    /* 4us acquisition time per sample */
 552         .median                 = 2,    /* do 8 measurements */
 553         .averaging              = 1,    /* take the average of 4 middle samples */
 554         .pen_down_acc_interval  = 255,  /* 9.4 ms */
 555         .gpio_output            = 1,    /* configure AUX/VBAT/GPIO as GPIO output */
 556         .gpio_default           = 1,    /* During initialization set GPIO = HIGH */
 557 };
 558 #endif
 559
 560 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 561 static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
 562         .enable_dma = 0,
 563         .bits_per_word = 16,
 564 };
 565 #endif
 566
 567 #if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
 568          && defined(CONFIG_SND_SOC_WM8731_SPI)
 569 static struct bfin5xx_spi_chip spi_wm8731_chip_info = {
 570         .enable_dma = 0,
 571         .bits_per_word = 16,
 572 };
 573 #endif
 574
 575 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 576 static struct bfin5xx_spi_chip spidev_chip_info = {
 577         .enable_dma = 0,
 578         .bits_per_word = 8,
 579 };
 580 #endif
 581
 582 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 583 #if defined(CONFIG_MTD_M25P80) \
 584         || defined(CONFIG_MTD_M25P80_MODULE)
 585         {
 586                 /* the modalias must be the same as spi device driver name */
 587                 .modalias = "m25p80", /* Name of spi_driver for this device */
 588                 .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
 589                 .bus_num = 0, /* Framework bus number */
 590                 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
 591                 .platform_data = &bfin_spi_flash_data,
 592                 .controller_data = &spi_flash_chip_info,
 593                 .mode = SPI_MODE_3,
 594         },
 595 #endif
 596
 597 #if defined(CONFIG_BFIN_SPI_ADC) \
 598         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 599         {
 600                 .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
 601                 .max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
 602                 .bus_num = 0, /* Framework bus number */
 603                 .chip_select = 1, /* Framework chip select. */
 604                 .platform_data = NULL, /* No spi_driver specific config */
 605                 .controller_data = &spi_adc_chip_info,
 606         },
 607 #endif
 608
 609 #if defined(CONFIG_SND_BLACKFIN_AD1836) \
 610         || defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
 611         {
 612                 .modalias = "ad1836",
 613                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 614                 .bus_num = 0,
 615                 .chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
 616                 .controller_data = &ad1836_spi_chip_info,
 617         },
 618 #endif
 619 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 620         {
 621                 .modalias = "mmc_spi",
 622                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 623                 .bus_num = 0,
 624                 .chip_select = 3,
 625                 .controller_data = &mmc_spi_chip_info,
 626                 .mode = SPI_MODE_0,
 627         },
 628 #endif
 629
 630 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 631         {
 632                 .modalias               = "ad7877",
 633                 .platform_data          = &bfin_ad7877_ts_info,
 634                 .irq                    = IRQ_PF8,
 635                 .max_speed_hz   = 12500000,     /* max spi clock (SCK) speed in HZ */
 636                 .bus_num        = 0,
 637                 .chip_select  = 2,
 638                 .controller_data = &spi_ad7877_chip_info,
 639         },
 640 #endif
 641 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 642         {
 643                 .modalias = "ad7879",
 644                 .platform_data = &bfin_ad7879_ts_info,
 645                 .irq = IRQ_PF8,
 646                 .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
 647                 .bus_num = 0,
 648                 .chip_select = 3,
 649                 .controller_data = &spi_ad7879_chip_info,
 650                 .mode = SPI_CPHA | SPI_CPOL,
 651         },
 652 #endif
 653 #if defined(CONFIG_SND_SOC_WM8731) || defined(CONFIG_SND_SOC_WM8731_MODULE) \
 654          && defined(CONFIG_SND_SOC_WM8731_SPI)
 655         {
 656                 .modalias       = "wm8731",
 657                 .max_speed_hz   = 3125000,     /* max spi clock (SCK) speed in HZ */
 658                 .bus_num        = 0,
 659                 .chip_select    = 5,
 660                 .controller_data = &spi_wm8731_chip_info,
 661                 .mode = SPI_MODE_0,
 662         },
 663 #endif
 664 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 665         {
 666                 .modalias = "spidev",
 667                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 668                 .bus_num = 0,
 669                 .chip_select = 1,
 670                 .controller_data = &spidev_chip_info,
 671         },
 672 #endif
 673 };
 674
 675 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 676 /* SPI controller data */
 677 static struct bfin5xx_spi_master bfin_spi0_info = {
 678         .num_chipselect = 8,
 679         .enable_dma = 1,  /* master has the ability to do dma transfer */
 680         .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 681 };
 682
 683 /* SPI (0) */
 684 static struct resource bfin_spi0_resource[] = {
 685         [0] = {
 686                 .start = SPI0_REGBASE,
 687                 .end   = SPI0_REGBASE + 0xFF,
 688                 .flags = IORESOURCE_MEM,
 689                 },
 690         [1] = {
 691                 .start = CH_SPI,
 692                 .end   = CH_SPI,
 693                 .flags = IORESOURCE_DMA,
 694         },
 695         [2] = {
 696                 .start = IRQ_SPI,
 697                 .end   = IRQ_SPI,
 698                 .flags = IORESOURCE_IRQ,
 699         },
 700 };
 701
 702 static struct platform_device bfin_spi0_device = {
 703         .name = "bfin-spi",
 704         .id = 0, /* Bus number */
 705         .num_resources = ARRAY_SIZE(bfin_spi0_resource),
 706         .resource = bfin_spi0_resource,
 707         .dev = {
 708                 .platform_data = &bfin_spi0_info, /* Passed to driver */
 709         },
 710 };
 711 #endif  /* spi master and devices */
 712
 713 #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
 714 static struct platform_device bfin_fb_device = {
 715         .name = "bf537-lq035",
 716 };
 717 #endif
 718
 719 #if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
 720 static struct platform_device bfin_fb_adv7393_device = {
 721         .name = "bfin-adv7393",
 722 };
 723 #endif
 724
 725 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
 726 static struct resource bfin_uart_resources[] = {
 727 #ifdef CONFIG_SERIAL_BFIN_UART0
 728         {
 729                 .start = 0xFFC00400,
 730                 .end = 0xFFC004FF,
 731                 .flags = IORESOURCE_MEM,
 732         },
 733 #endif
 734 #ifdef CONFIG_SERIAL_BFIN_UART1
 735         {
 736                 .start = 0xFFC02000,
 737                 .end = 0xFFC020FF,
 738                 .flags = IORESOURCE_MEM,
 739         },
 740 #endif
 741 };
 742
 743 static struct platform_device bfin_uart_device = {
 744         .name = "bfin-uart",
 745         .id = 1,
 746         .num_resources = ARRAY_SIZE(bfin_uart_resources),
 747         .resource = bfin_uart_resources,
 748 };
 749 #endif
 750
 751 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 752 #ifdef CONFIG_BFIN_SIR0
 753 static struct resource bfin_sir0_resources[] = {
 754         {
 755                 .start = 0xFFC00400,
 756                 .end = 0xFFC004FF,
 757                 .flags = IORESOURCE_MEM,
 758         },
 759         {
 760                 .start = IRQ_UART0_RX,
 761                 .end = IRQ_UART0_RX+1,
 762                 .flags = IORESOURCE_IRQ,
 763         },
 764         {
 765                 .start = CH_UART0_RX,
 766                 .end = CH_UART0_RX+1,
 767                 .flags = IORESOURCE_DMA,
 768         },
 769 };
 770
 771 static struct platform_device bfin_sir0_device = {
 772         .name = "bfin_sir",
 773         .id = 0,
 774         .num_resources = ARRAY_SIZE(bfin_sir0_resources),
 775         .resource = bfin_sir0_resources,
 776 };
 777 #endif
 778 #ifdef CONFIG_BFIN_SIR1
 779 static struct resource bfin_sir1_resources[] = {
 780         {
 781                 .start = 0xFFC02000,
 782                 .end = 0xFFC020FF,
 783                 .flags = IORESOURCE_MEM,
 784         },
 785         {
 786                 .start = IRQ_UART1_RX,
 787                 .end = IRQ_UART1_RX+1,
 788                 .flags = IORESOURCE_IRQ,
 789         },
 790         {
 791                 .start = CH_UART1_RX,
 792                 .end = CH_UART1_RX+1,
 793                 .flags = IORESOURCE_DMA,
 794         },
 795 };
 796
 797 static struct platform_device bfin_sir1_device = {
 798         .name = "bfin_sir",
 799         .id = 1,
 800         .num_resources = ARRAY_SIZE(bfin_sir1_resources),
 801         .resource = bfin_sir1_resources,
 802 };
 803 #endif
 804 #endif
 805
 806 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 807 static struct resource bfin_twi0_resource[] = {
 808         [0] = {
 809                 .start = TWI0_REGBASE,
 810                 .end   = TWI0_REGBASE,
 811                 .flags = IORESOURCE_MEM,
 812         },
 813         [1] = {
 814                 .start = IRQ_TWI,
 815                 .end   = IRQ_TWI,
 816                 .flags = IORESOURCE_IRQ,
 817         },
 818 };
 819
 820 static struct platform_device i2c_bfin_twi_device = {
 821         .name = "i2c-bfin-twi",
 822         .id = 0,
 823         .num_resources = ARRAY_SIZE(bfin_twi0_resource),
 824         .resource = bfin_twi0_resource,
 825 };
 826 #endif
 827
 828 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 829 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
 830         {
 831                 I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 832         },
 833 #endif
 834 #if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
 835         {
 836                 I2C_BOARD_INFO("pcf8574_keypad", 0x27),
 837                 .irq = IRQ_PF8,
 838         },
 839 #endif
 840 };
 841
 842 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
 843 static struct platform_device bfin_sport0_uart_device = {
 844         .name = "bfin-sport-uart",
 845         .id = 0,
 846 };
 847
 848 static struct platform_device bfin_sport1_uart_device = {
 849         .name = "bfin-sport-uart",
 850         .id = 1,
 851 };
 852 #endif
 853
 854 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
 855 #include <linux/input.h>
 856 #include <linux/gpio_keys.h>
 857
 858 static struct gpio_keys_button bfin_gpio_keys_table[] = {
 859         {BTN_0, GPIO_PG0, 1, "gpio-keys: BTN0"},
 860         {BTN_1, GPIO_PG13, 1, "gpio-keys: BTN1"},
 861 };
 862
 863 static struct gpio_keys_platform_data bfin_gpio_keys_data = {
 864         .buttons        = bfin_gpio_keys_table,
 865         .nbuttons       = ARRAY_SIZE(bfin_gpio_keys_table),
 866 };
 867
 868 static struct platform_device bfin_device_gpiokeys = {
 869         .name      = "gpio-keys",
 870         .dev = {
 871                 .platform_data = &bfin_gpio_keys_data,
 872         },
 873 };
 874 #endif
 875
 876 #if defined(CONFIG_JOYSTICK_BFIN_ROTARY) || defined(CONFIG_JOYSTICK_BFIN_ROTARY_MODULE)
 877 #include <linux/input.h>
 878 #include <asm/bfin_rotary.h>
 879
 880 static struct bfin_rotary_platform_data bfin_rotary_data = {
 881         /*.rotary_up_key     = KEY_UP,*/
 882         /*.rotary_down_key   = KEY_DOWN,*/
 883         .rotary_rel_code   = REL_WHEEL,
 884         .rotary_button_key = KEY_ENTER,
 885         .debounce          = 10,        /* 0..17 */
 886         .mode              = ROT_QUAD_ENC | ROT_DEBE,
 887 };
 888
 889 static struct resource bfin_rotary_resources[] = {
 890         {
 891                 .start = IRQ_CNT,
 892                 .end = IRQ_CNT,
 893                 .flags = IORESOURCE_IRQ,
 894         },
 895 };
 896
 897 static struct platform_device bfin_rotary_device = {
 898         .name           = "bfin-rotary",
 899         .id             = -1,
 900         .num_resources  = ARRAY_SIZE(bfin_rotary_resources),
 901         .resource       = bfin_rotary_resources,
 902         .dev            = {
 903                 .platform_data = &bfin_rotary_data,
 904         },
 905 };
 906 #endif
 907
 908 static struct resource bfin_gpios_resources = {
 909         .start = 0,
 910         .end   = MAX_BLACKFIN_GPIOS - 1,
 911         .flags = IORESOURCE_IRQ,
 912 };
 913
 914 static struct platform_device bfin_gpios_device = {
 915         .name = "simple-gpio",
 916         .id = -1,
 917         .num_resources = 1,
 918         .resource = &bfin_gpios_resources,
 919 };
 920
 921 static const unsigned int cclk_vlev_datasheet[] =
 922 {
 923         VRPAIR(VLEV_100, 400000000),
 924         VRPAIR(VLEV_105, 426000000),
 925         VRPAIR(VLEV_110, 500000000),
 926         VRPAIR(VLEV_115, 533000000),
 927         VRPAIR(VLEV_120, 600000000),
 928 };
 929
 930 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
 931         .tuple_tab = cclk_vlev_datasheet,
 932         .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
 933         .vr_settling_time = 25 /* us */,
 934 };
 935
 936 static struct platform_device bfin_dpmc = {
 937         .name = "bfin dpmc",
 938         .dev = {
 939                 .platform_data = &bfin_dmpc_vreg_data,
 940         },
 941 };
 942
 943 static struct platform_device *stamp_devices[] __initdata = {
 944
 945         &bfin_dpmc,
 946
 947 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
 948         &bf5xx_nand_device,
 949 #endif
 950
 951 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
 952         &bfin_pcmcia_cf_device,
 953 #endif
 954
 955 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 956         &rtc_device,
 957 #endif
 958
 959 #if defined(CONFIG_USB_SL811_HCD) || defined(CONFIG_USB_SL811_HCD_MODULE)
 960         &sl811_hcd_device,
 961 #endif
 962
 963 #if defined(CONFIG_USB_ISP1362_HCD) || defined(CONFIG_USB_ISP1362_HCD_MODULE)
 964         &isp1362_hcd_device,
 965 #endif
 966
 967 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
 968         &bfin_isp1760_device,
 969 #endif
 970
 971 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
 972         &musb_device,
 973 #endif
 974
 975 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 976         &smc91x_device,
 977 #endif
 978
 979 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
 980         &dm9000_device,
 981 #endif
 982
 983 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 984         &bfin_mii_bus,
 985         &bfin_mac_device,
 986 #endif
 987
 988 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 989         &net2272_bfin_device,
 990 #endif
 991
 992 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 993         &bfin_spi0_device,
 994 #endif
 995
 996 #if defined(CONFIG_FB_BF537_LQ035) || defined(CONFIG_FB_BF537_LQ035_MODULE)
 997         &bfin_fb_device,
 998 #endif
 999
1000 #if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
1001         &bf52x_t350mcqb_device,
1002 #endif
1003
1004 #if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
1005         &bfin_fb_adv7393_device,
1006 #endif
1007
1008 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
1009         &bfin_uart_device,
1010 #endif
1011
1012 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
1013 #ifdef CONFIG_BFIN_SIR0
1014         &bfin_sir0_device,
1015 #endif
1016 #ifdef CONFIG_BFIN_SIR1
1017         &bfin_sir1_device,
1018 #endif
1019 #endif
1020
1021 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
1022         &i2c_bfin_twi_device,
1023 #endif
1024
1025 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
1026         &bfin_sport0_uart_device,
1027         &bfin_sport1_uart_device,
1028 #endif
1029
1030 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
1031         &bfin_device_gpiokeys,
1032 #endif
1033
1034 #if defined(CONFIG_JOYSTICK_BFIN_ROTARY) || defined(CONFIG_JOYSTICK_BFIN_ROTARY_MODULE)
1035         &bfin_rotary_device,
1036 #endif
1037
1038 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
1039         &ezkit_flash_device,
1040 #endif
1041
1042         &bfin_gpios_device,
1043 };
1044
1045 static int __init ezkit_init(void)
1046 {
1047         printk(KERN_INFO "%s(): registering device resources\n", __func__);
1048         i2c_register_board_info(0, bfin_i2c_board_info,
1049                                 ARRAY_SIZE(bfin_i2c_board_info));
1050         platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
1051         spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
1052         return 0;
1053 }
1054
1055 arch_initcall(ezkit_init);
1056
1057 void native_machine_restart(char *cmd)
1058 {
1059         /* workaround reboot hang when booting from SPI */
1060         if ((bfin_read_SYSCR() & 0x7) == 0x3)
1061                 bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
1062 }
1063
1064 void bfin_get_ether_addr(char *addr)
1065 {
1066         /* the MAC is stored in OTP memory page 0xDF */
1067         u32 ret;
1068         u64 otp_mac;
1069         u32 (*otp_read)(u32 page, u32 flags, u64 *page_content) = (void *)0xEF00001A;
1070
1071         ret = otp_read(0xDF, 0x00, &otp_mac);
1072         if (!(ret & 0x1)) {
1073                 char *otp_mac_p = (char *)&otp_mac;
1074                 for (ret = 0; ret < 6; ++ret)
1075                         addr[ret] = otp_mac_p[5 - ret];
1076         }
1077 }
1078 EXPORT_SYMBOL(bfin_get_ether_addr);