arch/blackfin/mach-bf527/boards/ezkit.c

   1 /*
   2  * Copyright 2004-2009 Analog Devices Inc.
   3  *                2005 National ICT Australia (NICTA)
   4  *                      Aidan Williams <aidan@nicta.com.au>
   5  *
   6  * Licensed under the GPL-2 or later.
   7  */
   8
   9 #include <linux/device.h>
  10 #include <linux/platform_device.h>
  11 #include <linux/mtd/mtd.h>
  12 #include <linux/mtd/partitions.h>
  13 #include <linux/mtd/physmap.h>
  14 #include <linux/spi/spi.h>
  15 #include <linux/spi/flash.h>
  16 #include <linux/i2c.h>
  17 #include <linux/irq.h>
  18 #include <linux/interrupt.h>
  19 #include <linux/usb/musb.h>
  20 #include <linux/leds.h>
  21 #include <linux/input.h>
  22 #include <asm/dma.h>
  23 #include <asm/bfin5xx_spi.h>
  24 #include <asm/reboot.h>
  25 #include <asm/nand.h>
  26 #include <asm/portmux.h>
  27 #include <asm/dpmc.h>
  28 #include <linux/spi/ad7877.h>
  29 #include <asm/bfin_sport.h>
  30
  31 /*
  32  * Name the Board for the /proc/cpuinfo
  33  */
  34 #ifdef CONFIG_BFIN527_EZKIT_V2
  35 const char bfin_board_name[] = "ADI BF527-EZKIT V2";
  36 #else
  37 const char bfin_board_name[] = "ADI BF527-EZKIT";
  38 #endif
  39
  40 /*
  41  *  Driver needs to know address, irq and flag pin.
  42  */
  43
  44 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
  45 #include <linux/usb/isp1760.h>
  46 static struct resource bfin_isp1760_resources[] = {
  47         [0] = {
  48                 .start  = 0x203C0000,
  49                 .end    = 0x203C0000 + 0x000fffff,
  50                 .flags  = IORESOURCE_MEM,
  51         },
  52         [1] = {
  53                 .start  = IRQ_PF7,
  54                 .end    = IRQ_PF7,
  55                 .flags  = IORESOURCE_IRQ,
  56         },
  57 };
  58
  59 static struct isp1760_platform_data isp1760_priv = {
  60         .is_isp1761 = 0,
  61         .bus_width_16 = 1,
  62         .port1_otg = 0,
  63         .analog_oc = 0,
  64         .dack_polarity_high = 0,
  65         .dreq_polarity_high = 0,
  66 };
  67
  68 static struct platform_device bfin_isp1760_device = {
  69         .name           = "isp1760",
  70         .id             = 0,
  71         .dev = {
  72                 .platform_data = &isp1760_priv,
  73         },
  74         .num_resources  = ARRAY_SIZE(bfin_isp1760_resources),
  75         .resource       = bfin_isp1760_resources,
  76 };
  77 #endif
  78
  79 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
  80 static struct resource musb_resources[] = {
  81         [0] = {
  82                 .start  = 0xffc03800,
  83                 .end    = 0xffc03cff,
  84                 .flags  = IORESOURCE_MEM,
  85         },
  86         [1] = { /* general IRQ */
  87                 .start  = IRQ_USB_INT0,
  88                 .end    = IRQ_USB_INT0,
  89                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
  90                 .name   = "mc"
  91         },
  92         [2] = { /* DMA IRQ */
  93                 .start  = IRQ_USB_DMA,
  94                 .end    = IRQ_USB_DMA,
  95                 .flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
  96                 .name   = "dma"
  97         },
  98 };
  99
 100 static struct musb_hdrc_config musb_config = {
 101         .multipoint     = 0,
 102         .dyn_fifo       = 0,
 103         .soft_con       = 1,
 104         .dma            = 1,
 105         .num_eps        = 8,
 106         .dma_channels   = 8,
 107         .gpio_vrsel     = GPIO_PG13,
 108         /* Some custom boards need to be active low, just set it to "0"
 109          * if it is the case.
 110          */
 111         .gpio_vrsel_active      = 1,
 112         .clkin          = 24,           /* musb CLKIN in MHZ */
 113 };
 114
 115 static struct musb_hdrc_platform_data musb_plat = {
 116 #if defined(CONFIG_USB_MUSB_OTG)
 117         .mode           = MUSB_OTG,
 118 #elif defined(CONFIG_USB_MUSB_HDRC_HCD)
 119         .mode           = MUSB_HOST,
 120 #elif defined(CONFIG_USB_GADGET_MUSB_HDRC)
 121         .mode           = MUSB_PERIPHERAL,
 122 #endif
 123         .config         = &musb_config,
 124 };
 125
 126 static u64 musb_dmamask = ~(u32)0;
 127
 128 static struct platform_device musb_device = {
 129         .name           = "musb-blackfin",
 130         .id             = 0,
 131         .dev = {
 132                 .dma_mask               = &musb_dmamask,
 133                 .coherent_dma_mask      = 0xffffffff,
 134                 .platform_data          = &musb_plat,
 135         },
 136         .num_resources  = ARRAY_SIZE(musb_resources),
 137         .resource       = musb_resources,
 138 };
 139 #endif
 140
 141 #if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
 142
 143 static struct resource bf52x_t350mcqb_resources[] = {
 144         {
 145                 .start = IRQ_PPI_ERROR,
 146                 .end = IRQ_PPI_ERROR,
 147                 .flags = IORESOURCE_IRQ,
 148         },
 149 };
 150
 151 static struct platform_device bf52x_t350mcqb_device = {
 152         .name           = "bfin-t350mcqb",
 153         .id             = -1,
 154         .num_resources  = ARRAY_SIZE(bf52x_t350mcqb_resources),
 155         .resource       = bf52x_t350mcqb_resources,
 156 };
 157 #endif
 158
 159 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 160 #include <asm/bfin-lq035q1.h>
 161
 162 static struct bfin_lq035q1fb_disp_info bfin_lq035q1_data = {
 163         .mode = LQ035_NORM | LQ035_RGB | LQ035_RL | LQ035_TB,
 164         .ppi_mode = USE_RGB565_8_BIT_PPI,
 165 };
 166
 167 static struct resource bfin_lq035q1_resources[] = {
 168         {
 169                 .start = IRQ_PPI_ERROR,
 170                 .end = IRQ_PPI_ERROR,
 171                 .flags = IORESOURCE_IRQ,
 172         },
 173 };
 174
 175 static struct platform_device bfin_lq035q1_device = {
 176         .name           = "bfin-lq035q1",
 177         .id             = -1,
 178         .num_resources  = ARRAY_SIZE(bfin_lq035q1_resources),
 179         .resource       = bfin_lq035q1_resources,
 180         .dev            = {
 181                 .platform_data = &bfin_lq035q1_data,
 182         },
 183 };
 184 #endif
 185
 186 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
 187 static struct mtd_partition ezkit_partitions[] = {
 188         {
 189                 .name       = "bootloader(nor)",
 190                 .size       = 0x40000,
 191                 .offset     = 0,
 192         }, {
 193                 .name       = "linux kernel(nor)",
 194                 .size       = 0x1C0000,
 195                 .offset     = MTDPART_OFS_APPEND,
 196         }, {
 197                 .name       = "file system(nor)",
 198                 .size       = MTDPART_SIZ_FULL,
 199                 .offset     = MTDPART_OFS_APPEND,
 200         }
 201 };
 202
 203 static struct physmap_flash_data ezkit_flash_data = {
 204         .width      = 2,
 205         .parts      = ezkit_partitions,
 206         .nr_parts   = ARRAY_SIZE(ezkit_partitions),
 207 };
 208
 209 static struct resource ezkit_flash_resource = {
 210         .start = 0x20000000,
 211         .end   = 0x203fffff,
 212         .flags = IORESOURCE_MEM,
 213 };
 214
 215 static struct platform_device ezkit_flash_device = {
 216         .name          = "physmap-flash",
 217         .id            = 0,
 218         .dev = {
 219                 .platform_data = &ezkit_flash_data,
 220         },
 221         .num_resources = 1,
 222         .resource      = &ezkit_flash_resource,
 223 };
 224 #endif
 225
 226 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
 227 static struct mtd_partition partition_info[] = {
 228         {
 229                 .name = "bootloader(nand)",
 230                 .offset = 0,
 231                 .size = 0x40000,
 232         }, {
 233                 .name = "linux kernel(nand)",
 234                 .offset = MTDPART_OFS_APPEND,
 235                 .size = 4 * 1024 * 1024,
 236         },
 237         {
 238                 .name = "file system(nand)",
 239                 .offset = MTDPART_OFS_APPEND,
 240                 .size = MTDPART_SIZ_FULL,
 241         },
 242 };
 243
 244 static struct bf5xx_nand_platform bf5xx_nand_platform = {
 245         .data_width = NFC_NWIDTH_8,
 246         .partitions = partition_info,
 247         .nr_partitions = ARRAY_SIZE(partition_info),
 248         .rd_dly = 3,
 249         .wr_dly = 3,
 250 };
 251
 252 static struct resource bf5xx_nand_resources[] = {
 253         {
 254                 .start = NFC_CTL,
 255                 .end = NFC_DATA_RD + 2,
 256                 .flags = IORESOURCE_MEM,
 257         },
 258         {
 259                 .start = CH_NFC,
 260                 .end = CH_NFC,
 261                 .flags = IORESOURCE_IRQ,
 262         },
 263 };
 264
 265 static struct platform_device bf5xx_nand_device = {
 266         .name = "bf5xx-nand",
 267         .id = 0,
 268         .num_resources = ARRAY_SIZE(bf5xx_nand_resources),
 269         .resource = bf5xx_nand_resources,
 270         .dev = {
 271                 .platform_data = &bf5xx_nand_platform,
 272         },
 273 };
 274 #endif
 275
 276 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
 277 static struct resource bfin_pcmcia_cf_resources[] = {
 278         {
 279                 .start = 0x20310000, /* IO PORT */
 280                 .end = 0x20312000,
 281                 .flags = IORESOURCE_MEM,
 282         }, {
 283                 .start = 0x20311000, /* Attribute Memory */
 284                 .end = 0x20311FFF,
 285                 .flags = IORESOURCE_MEM,
 286         }, {
 287                 .start = IRQ_PF4,
 288                 .end = IRQ_PF4,
 289                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
 290         }, {
 291                 .start = 6, /* Card Detect PF6 */
 292                 .end = 6,
 293                 .flags = IORESOURCE_IRQ,
 294         },
 295 };
 296
 297 static struct platform_device bfin_pcmcia_cf_device = {
 298         .name = "bfin_cf_pcmcia",
 299         .id = -1,
 300         .num_resources = ARRAY_SIZE(bfin_pcmcia_cf_resources),
 301         .resource = bfin_pcmcia_cf_resources,
 302 };
 303 #endif
 304
 305 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
 306 static struct platform_device rtc_device = {
 307         .name = "rtc-bfin",
 308         .id   = -1,
 309 };
 310 #endif
 311
 312 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
 313 #include <linux/smc91x.h>
 314
 315 static struct smc91x_platdata smc91x_info = {
 316         .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
 317         .leda = RPC_LED_100_10,
 318         .ledb = RPC_LED_TX_RX,
 319 };
 320
 321 static struct resource smc91x_resources[] = {
 322         {
 323                 .name = "smc91x-regs",
 324                 .start = 0x20300300,
 325                 .end = 0x20300300 + 16,
 326                 .flags = IORESOURCE_MEM,
 327         }, {
 328
 329                 .start = IRQ_PF7,
 330                 .end = IRQ_PF7,
 331                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 332         },
 333 };
 334 static struct platform_device smc91x_device = {
 335         .name = "smc91x",
 336         .id = 0,
 337         .num_resources = ARRAY_SIZE(smc91x_resources),
 338         .resource = smc91x_resources,
 339         .dev    = {
 340                 .platform_data  = &smc91x_info,
 341         },
 342 };
 343 #endif
 344
 345 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
 346 static struct resource dm9000_resources[] = {
 347         [0] = {
 348                 .start  = 0x203FB800,
 349                 .end    = 0x203FB800 + 1,
 350                 .flags  = IORESOURCE_MEM,
 351         },
 352         [1] = {
 353                 .start  = 0x203FB800 + 4,
 354                 .end    = 0x203FB800 + 5,
 355                 .flags  = IORESOURCE_MEM,
 356         },
 357         [2] = {
 358                 .start  = IRQ_PF9,
 359                 .end    = IRQ_PF9,
 360                 .flags  = (IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE),
 361         },
 362 };
 363
 364 static struct platform_device dm9000_device = {
 365         .name           = "dm9000",
 366         .id             = -1,
 367         .num_resources  = ARRAY_SIZE(dm9000_resources),
 368         .resource       = dm9000_resources,
 369 };
 370 #endif
 371
 372 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
 373 #include <linux/bfin_mac.h>
 374 static const unsigned short bfin_mac_peripherals[] = P_RMII0;
 375
 376 static struct bfin_phydev_platform_data bfin_phydev_data[] = {
 377         {
 378                 .addr = 1,
 379                 .irq = IRQ_MAC_PHYINT,
 380         },
 381 };
 382
 383 static struct bfin_mii_bus_platform_data bfin_mii_bus_data = {
 384         .phydev_number = 1,
 385         .phydev_data = bfin_phydev_data,
 386         .phy_mode = PHY_INTERFACE_MODE_RMII,
 387         .mac_peripherals = bfin_mac_peripherals,
 388 };
 389
 390 static struct platform_device bfin_mii_bus = {
 391         .name = "bfin_mii_bus",
 392         .dev = {
 393                 .platform_data = &bfin_mii_bus_data,
 394         }
 395 };
 396
 397 static struct platform_device bfin_mac_device = {
 398         .name = "bfin_mac",
 399         .dev = {
 400                 .platform_data = &bfin_mii_bus,
 401         }
 402 };
 403 #endif
 404
 405 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
 406 static struct resource net2272_bfin_resources[] = {
 407         {
 408                 .start = 0x20300000,
 409                 .end = 0x20300000 + 0x100,
 410                 .flags = IORESOURCE_MEM,
 411         }, {
 412                 .start = 1,
 413                 .flags = IORESOURCE_BUS,
 414         }, {
 415                 .start = IRQ_PF7,
 416                 .end = IRQ_PF7,
 417                 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
 418         },
 419 };
 420
 421 static struct platform_device net2272_bfin_device = {
 422         .name = "net2272",
 423         .id = -1,
 424         .num_resources = ARRAY_SIZE(net2272_bfin_resources),
 425         .resource = net2272_bfin_resources,
 426 };
 427 #endif
 428
 429 #if defined(CONFIG_MTD_M25P80) \
 430         || defined(CONFIG_MTD_M25P80_MODULE)
 431 static struct mtd_partition bfin_spi_flash_partitions[] = {
 432         {
 433                 .name = "bootloader(spi)",
 434                 .size = 0x00040000,
 435                 .offset = 0,
 436                 .mask_flags = MTD_CAP_ROM
 437         }, {
 438                 .name = "linux kernel(spi)",
 439                 .size = MTDPART_SIZ_FULL,
 440                 .offset = MTDPART_OFS_APPEND,
 441         }
 442 };
 443
 444 static struct flash_platform_data bfin_spi_flash_data = {
 445         .name = "m25p80",
 446         .parts = bfin_spi_flash_partitions,
 447         .nr_parts = ARRAY_SIZE(bfin_spi_flash_partitions),
 448         .type = "m25p16",
 449 };
 450
 451 /* SPI flash chip (m25p64) */
 452 static struct bfin5xx_spi_chip spi_flash_chip_info = {
 453         .enable_dma = 0,         /* use dma transfer with this chip*/
 454         .bits_per_word = 8,
 455 };
 456 #endif
 457
 458 #if defined(CONFIG_BFIN_SPI_ADC) \
 459         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 460 /* SPI ADC chip */
 461 static struct bfin5xx_spi_chip spi_adc_chip_info = {
 462         .enable_dma = 1,         /* use dma transfer with this chip*/
 463         .bits_per_word = 16,
 464 };
 465 #endif
 466
 467 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
 468         || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 469 static struct bfin5xx_spi_chip ad1836_spi_chip_info = {
 470         .enable_dma = 0,
 471         .bits_per_word = 16,
 472 };
 473 #endif
 474
 475 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 476 static struct bfin5xx_spi_chip  mmc_spi_chip_info = {
 477         .enable_dma = 0,
 478         .bits_per_word = 8,
 479 };
 480 #endif
 481
 482 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 483 static struct bfin5xx_spi_chip spi_ad7877_chip_info = {
 484         .enable_dma = 0,
 485         .bits_per_word = 16,
 486 };
 487
 488 static const struct ad7877_platform_data bfin_ad7877_ts_info = {
 489         .model                  = 7877,
 490         .vref_delay_usecs       = 50,   /* internal, no capacitor */
 491         .x_plate_ohms           = 419,
 492         .y_plate_ohms           = 486,
 493         .pressure_max           = 1000,
 494         .pressure_min           = 0,
 495         .stopacq_polarity       = 1,
 496         .first_conversion_delay = 3,
 497         .acquisition_time       = 1,
 498         .averaging              = 1,
 499         .pen_down_acc_interval  = 1,
 500 };
 501 #endif
 502
 503 #if defined(CONFIG_TOUCHSCREEN_AD7879) || defined(CONFIG_TOUCHSCREEN_AD7879_MODULE)
 504 #include <linux/spi/ad7879.h>
 505 static const struct ad7879_platform_data bfin_ad7879_ts_info = {
 506         .model                  = 7879, /* Model = AD7879 */
 507         .x_plate_ohms           = 620,  /* 620 Ohm from the touch datasheet */
 508         .pressure_max           = 10000,
 509         .pressure_min           = 0,
 510         .first_conversion_delay = 3,    /* wait 512us before do a first conversion */
 511         .acquisition_time       = 1,    /* 4us acquisition time per sample */
 512         .median                 = 2,    /* do 8 measurements */
 513         .averaging              = 1,    /* take the average of 4 middle samples */
 514         .pen_down_acc_interval  = 255,  /* 9.4 ms */
 515         .gpio_export            = 0,    /* Export GPIO to gpiolib */
 516 };
 517 #endif
 518
 519 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 520 static struct bfin5xx_spi_chip spi_ad7879_chip_info = {
 521         .enable_dma = 0,
 522         .bits_per_word = 16,
 523 };
 524 #endif
 525
 526 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 527 static struct bfin5xx_spi_chip spidev_chip_info = {
 528         .enable_dma = 0,
 529         .bits_per_word = 8,
 530 };
 531 #endif
 532
 533 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
 534         defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
 535
 536 static const u16 bfin_snd_pin[][7] = {
 537         {P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
 538                 P_SPORT0_DRPRI, P_SPORT0_RSCLK, 0, 0},
 539         {P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
 540                 P_SPORT1_DRPRI, P_SPORT1_RSCLK, P_SPORT1_TFS, 0},
 541 };
 542
 543 static struct bfin_snd_platform_data bfin_snd_data[] = {
 544         {
 545                 .pin_req = &bfin_snd_pin[0][0],
 546         },
 547         {
 548                 .pin_req = &bfin_snd_pin[1][0],
 549         },
 550 };
 551
 552 #define BFIN_SND_RES(x) \
 553         [x] = { \
 554                 { \
 555                         .start = SPORT##x##_TCR1, \
 556                         .end = SPORT##x##_TCR1, \
 557                         .flags = IORESOURCE_MEM \
 558                 }, \
 559                 { \
 560                         .start = CH_SPORT##x##_RX, \
 561                         .end = CH_SPORT##x##_RX, \
 562                         .flags = IORESOURCE_DMA, \
 563                 }, \
 564                 { \
 565                         .start = CH_SPORT##x##_TX, \
 566                         .end = CH_SPORT##x##_TX, \
 567                         .flags = IORESOURCE_DMA, \
 568                 }, \
 569                 { \
 570                         .start = IRQ_SPORT##x##_ERROR, \
 571                         .end = IRQ_SPORT##x##_ERROR, \
 572                         .flags = IORESOURCE_IRQ, \
 573                 } \
 574         }
 575
 576 static struct resource bfin_snd_resources[][4] = {
 577         BFIN_SND_RES(0),
 578         BFIN_SND_RES(1),
 579 };
 580
 581 static struct platform_device bfin_pcm = {
 582         .name = "bfin-pcm-audio",
 583         .id = -1,
 584 };
 585 #endif
 586
 587 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
 588 static struct platform_device bfin_i2s = {
 589         .name = "bfin-i2s",
 590         .id = CONFIG_SND_BF5XX_SPORT_NUM,
 591         .num_resources = ARRAY_SIZE(bfin_snd_resources[CONFIG_SND_BF5XX_SPORT_NUM]),
 592         .resource = bfin_snd_resources[CONFIG_SND_BF5XX_SPORT_NUM],
 593         .dev = {
 594                 .platform_data = &bfin_snd_data[CONFIG_SND_BF5XX_SPORT_NUM],
 595         },
 596 };
 597 #endif
 598
 599 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
 600 static struct platform_device bfin_tdm = {
 601         .name = "bfin-tdm",
 602         .id = CONFIG_SND_BF5XX_SPORT_NUM,
 603         .num_resources = ARRAY_SIZE(bfin_snd_resources[CONFIG_SND_BF5XX_SPORT_NUM]),
 604         .resource = bfin_snd_resources[CONFIG_SND_BF5XX_SPORT_NUM],
 605         .dev = {
 606                 .platform_data = &bfin_snd_data[CONFIG_SND_BF5XX_SPORT_NUM],
 607         },
 608 };
 609 #endif
 610
 611 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 612 static struct bfin5xx_spi_chip lq035q1_spi_chip_info = {
 613         .enable_dma     = 0,
 614         .bits_per_word  = 8,
 615 };
 616 #endif
 617
 618 static struct spi_board_info bfin_spi_board_info[] __initdata = {
 619 #if defined(CONFIG_MTD_M25P80) \
 620         || defined(CONFIG_MTD_M25P80_MODULE)
 621         {
 622                 /* the modalias must be the same as spi device driver name */
 623                 .modalias = "m25p80", /* Name of spi_driver for this device */
 624                 .max_speed_hz = 25000000,     /* max spi clock (SCK) speed in HZ */
 625                 .bus_num = 0, /* Framework bus number */
 626                 .chip_select = 1, /* Framework chip select. On STAMP537 it is SPISSEL1*/
 627                 .platform_data = &bfin_spi_flash_data,
 628                 .controller_data = &spi_flash_chip_info,
 629                 .mode = SPI_MODE_3,
 630         },
 631 #endif
 632
 633 #if defined(CONFIG_BFIN_SPI_ADC) \
 634         || defined(CONFIG_BFIN_SPI_ADC_MODULE)
 635         {
 636                 .modalias = "bfin_spi_adc", /* Name of spi_driver for this device */
 637                 .max_speed_hz = 6250000,     /* max spi clock (SCK) speed in HZ */
 638                 .bus_num = 0, /* Framework bus number */
 639                 .chip_select = 1, /* Framework chip select. */
 640                 .platform_data = NULL, /* No spi_driver specific config */
 641                 .controller_data = &spi_adc_chip_info,
 642         },
 643 #endif
 644
 645 #if defined(CONFIG_SND_BF5XX_SOC_AD183X) \
 646         || defined(CONFIG_SND_BF5XX_SOC_AD183X_MODULE)
 647         {
 648                 .modalias = "ad183x",
 649                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 650                 .bus_num = 0,
 651                 .chip_select = 4,
 652                 .platform_data = "ad1836",
 653                 .controller_data = &ad1836_spi_chip_info,
 654                 .mode = SPI_MODE_3,
 655         },
 656 #endif
 657 #if defined(CONFIG_MMC_SPI) || defined(CONFIG_MMC_SPI_MODULE)
 658         {
 659                 .modalias = "mmc_spi",
 660                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 661                 .bus_num = 0,
 662                 .chip_select = 3,
 663                 .controller_data = &mmc_spi_chip_info,
 664                 .mode = SPI_MODE_0,
 665         },
 666 #endif
 667
 668 #if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
 669         {
 670                 .modalias               = "ad7877",
 671                 .platform_data          = &bfin_ad7877_ts_info,
 672                 .irq                    = IRQ_PF8,
 673                 .max_speed_hz   = 12500000,     /* max spi clock (SCK) speed in HZ */
 674                 .bus_num        = 0,
 675                 .chip_select  = 2,
 676                 .controller_data = &spi_ad7877_chip_info,
 677         },
 678 #endif
 679 #if defined(CONFIG_TOUCHSCREEN_AD7879_SPI) || defined(CONFIG_TOUCHSCREEN_AD7879_SPI_MODULE)
 680         {
 681                 .modalias = "ad7879",
 682                 .platform_data = &bfin_ad7879_ts_info,
 683                 .irq = IRQ_PF8,
 684                 .max_speed_hz = 5000000,     /* max spi clock (SCK) speed in HZ */
 685                 .bus_num = 0,
 686                 .chip_select = 3,
 687                 .controller_data = &spi_ad7879_chip_info,
 688                 .mode = SPI_CPHA | SPI_CPOL,
 689         },
 690 #endif
 691 #if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
 692         {
 693                 .modalias = "spidev",
 694                 .max_speed_hz = 3125000,     /* max spi clock (SCK) speed in HZ */
 695                 .bus_num = 0,
 696                 .chip_select = 1,
 697                 .controller_data = &spidev_chip_info,
 698         },
 699 #endif
 700 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
 701         {
 702                 .modalias = "bfin-lq035q1-spi",
 703                 .max_speed_hz = 20000000,     /* max spi clock (SCK) speed in HZ */
 704                 .bus_num = 0,
 705                 .chip_select = 7,
 706                 .controller_data = &lq035q1_spi_chip_info,
 707                 .mode = SPI_CPHA | SPI_CPOL,
 708         },
 709 #endif
 710 };
 711
 712 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
 713 /* SPI controller data */
 714 static struct bfin5xx_spi_master bfin_spi0_info = {
 715         .num_chipselect = 8,
 716         .enable_dma = 1,  /* master has the ability to do dma transfer */
 717         .pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
 718 };
 719
 720 /* SPI (0) */
 721 static struct resource bfin_spi0_resource[] = {
 722         [0] = {
 723                 .start = SPI0_REGBASE,
 724                 .end   = SPI0_REGBASE + 0xFF,
 725                 .flags = IORESOURCE_MEM,
 726                 },
 727         [1] = {
 728                 .start = CH_SPI,
 729                 .end   = CH_SPI,
 730                 .flags = IORESOURCE_DMA,
 731         },
 732         [2] = {
 733                 .start = IRQ_SPI,
 734                 .end   = IRQ_SPI,
 735                 .flags = IORESOURCE_IRQ,
 736         },
 737 };
 738
 739 static struct platform_device bfin_spi0_device = {
 740         .name = "bfin-spi",
 741         .id = 0, /* Bus number */
 742         .num_resources = ARRAY_SIZE(bfin_spi0_resource),
 743         .resource = bfin_spi0_resource,
 744         .dev = {
 745                 .platform_data = &bfin_spi0_info, /* Passed to driver */
 746         },
 747 };
 748 #endif  /* spi master and devices */
 749
 750 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
 751 #ifdef CONFIG_SERIAL_BFIN_UART0
 752 static struct resource bfin_uart0_resources[] = {
 753         {
 754                 .start = UART0_THR,
 755                 .end = UART0_GCTL+2,
 756                 .flags = IORESOURCE_MEM,
 757         },
 758         {
 759                 .start = IRQ_UART0_RX,
 760                 .end = IRQ_UART0_RX+1,
 761                 .flags = IORESOURCE_IRQ,
 762         },
 763         {
 764                 .start = IRQ_UART0_ERROR,
 765                 .end = IRQ_UART0_ERROR,
 766                 .flags = IORESOURCE_IRQ,
 767         },
 768         {
 769                 .start = CH_UART0_TX,
 770                 .end = CH_UART0_TX,
 771                 .flags = IORESOURCE_DMA,
 772         },
 773         {
 774                 .start = CH_UART0_RX,
 775                 .end = CH_UART0_RX,
 776                 .flags = IORESOURCE_DMA,
 777         },
 778 };
 779
 780 static unsigned short bfin_uart0_peripherals[] = {
 781         P_UART0_TX, P_UART0_RX, 0
 782 };
 783
 784 static struct platform_device bfin_uart0_device = {
 785         .name = "bfin-uart",
 786         .id = 0,
 787         .num_resources = ARRAY_SIZE(bfin_uart0_resources),
 788         .resource = bfin_uart0_resources,
 789         .dev = {
 790                 .platform_data = &bfin_uart0_peripherals, /* Passed to driver */
 791         },
 792 };
 793 #endif
 794 #ifdef CONFIG_SERIAL_BFIN_UART1
 795 static struct resource bfin_uart1_resources[] = {
 796         {
 797                 .start = UART1_THR,
 798                 .end = UART1_GCTL+2,
 799                 .flags = IORESOURCE_MEM,
 800         },
 801         {
 802                 .start = IRQ_UART1_RX,
 803                 .end = IRQ_UART1_RX+1,
 804                 .flags = IORESOURCE_IRQ,
 805         },
 806         {
 807                 .start = IRQ_UART1_ERROR,
 808                 .end = IRQ_UART1_ERROR,
 809                 .flags = IORESOURCE_IRQ,
 810         },
 811         {
 812                 .start = CH_UART1_TX,
 813                 .end = CH_UART1_TX,
 814                 .flags = IORESOURCE_DMA,
 815         },
 816         {
 817                 .start = CH_UART1_RX,
 818                 .end = CH_UART1_RX,
 819                 .flags = IORESOURCE_DMA,
 820         },
 821 #ifdef CONFIG_BFIN_UART1_CTSRTS
 822         {       /* CTS pin */
 823                 .start = GPIO_PF9,
 824                 .end = GPIO_PF9,
 825                 .flags = IORESOURCE_IO,
 826         },
 827         {       /* RTS pin */
 828                 .start = GPIO_PF10,
 829                 .end = GPIO_PF10,
 830                 .flags = IORESOURCE_IO,
 831         },
 832 #endif
 833 };
 834
 835 static unsigned short bfin_uart1_peripherals[] = {
 836         P_UART1_TX, P_UART1_RX, 0
 837 };
 838
 839 static struct platform_device bfin_uart1_device = {
 840         .name = "bfin-uart",
 841         .id = 1,
 842         .num_resources = ARRAY_SIZE(bfin_uart1_resources),
 843         .resource = bfin_uart1_resources,
 844         .dev = {
 845                 .platform_data = &bfin_uart1_peripherals, /* Passed to driver */
 846         },
 847 };
 848 #endif
 849 #endif
 850
 851 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
 852 #ifdef CONFIG_BFIN_SIR0
 853 static struct resource bfin_sir0_resources[] = {
 854         {
 855                 .start = 0xFFC00400,
 856                 .end = 0xFFC004FF,
 857                 .flags = IORESOURCE_MEM,
 858         },
 859         {
 860                 .start = IRQ_UART0_RX,
 861                 .end = IRQ_UART0_RX+1,
 862                 .flags = IORESOURCE_IRQ,
 863         },
 864         {
 865                 .start = CH_UART0_RX,
 866                 .end = CH_UART0_RX+1,
 867                 .flags = IORESOURCE_DMA,
 868         },
 869 };
 870
 871 static struct platform_device bfin_sir0_device = {
 872         .name = "bfin_sir",
 873         .id = 0,
 874         .num_resources = ARRAY_SIZE(bfin_sir0_resources),
 875         .resource = bfin_sir0_resources,
 876 };
 877 #endif
 878 #ifdef CONFIG_BFIN_SIR1
 879 static struct resource bfin_sir1_resources[] = {
 880         {
 881                 .start = 0xFFC02000,
 882                 .end = 0xFFC020FF,
 883                 .flags = IORESOURCE_MEM,
 884         },
 885         {
 886                 .start = IRQ_UART1_RX,
 887                 .end = IRQ_UART1_RX+1,
 888                 .flags = IORESOURCE_IRQ,
 889         },
 890         {
 891                 .start = CH_UART1_RX,
 892                 .end = CH_UART1_RX+1,
 893                 .flags = IORESOURCE_DMA,
 894         },
 895 };
 896
 897 static struct platform_device bfin_sir1_device = {
 898         .name = "bfin_sir",
 899         .id = 1,
 900         .num_resources = ARRAY_SIZE(bfin_sir1_resources),
 901         .resource = bfin_sir1_resources,
 902 };
 903 #endif
 904 #endif
 905
 906 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
 907 static struct resource bfin_twi0_resource[] = {
 908         [0] = {
 909                 .start = TWI0_REGBASE,
 910                 .end   = TWI0_REGBASE,
 911                 .flags = IORESOURCE_MEM,
 912         },
 913         [1] = {
 914                 .start = IRQ_TWI,
 915                 .end   = IRQ_TWI,
 916                 .flags = IORESOURCE_IRQ,
 917         },
 918 };
 919
 920 static struct platform_device i2c_bfin_twi_device = {
 921         .name = "i2c-bfin-twi",
 922         .id = 0,
 923         .num_resources = ARRAY_SIZE(bfin_twi0_resource),
 924         .resource = bfin_twi0_resource,
 925 };
 926 #endif
 927
 928 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
 929 #include <linux/mfd/adp5520.h>
 930
 931         /*
 932          *  ADP5520/5501 LEDs Data
 933          */
 934
 935 static struct led_info adp5520_leds[] = {
 936         {
 937                 .name = "adp5520-led1",
 938                 .default_trigger = "none",
 939                 .flags = FLAG_ID_ADP5520_LED1_ADP5501_LED0 | ADP5520_LED_OFFT_600ms,
 940         },
 941 };
 942
 943 static struct adp5520_leds_platform_data adp5520_leds_data = {
 944         .num_leds = ARRAY_SIZE(adp5520_leds),
 945         .leds = adp5520_leds,
 946         .fade_in = ADP5520_FADE_T_600ms,
 947         .fade_out = ADP5520_FADE_T_600ms,
 948         .led_on_time = ADP5520_LED_ONT_600ms,
 949 };
 950
 951         /*
 952          *  ADP5520 Keypad Data
 953          */
 954
 955 static const unsigned short adp5520_keymap[ADP5520_KEYMAPSIZE] = {
 956         [ADP5520_KEY(3, 3)]     = KEY_1,
 957         [ADP5520_KEY(2, 3)]     = KEY_2,
 958         [ADP5520_KEY(1, 3)]     = KEY_3,
 959         [ADP5520_KEY(0, 3)]     = KEY_UP,
 960         [ADP5520_KEY(3, 2)]     = KEY_4,
 961         [ADP5520_KEY(2, 2)]     = KEY_5,
 962         [ADP5520_KEY(1, 2)]     = KEY_6,
 963         [ADP5520_KEY(0, 2)]     = KEY_DOWN,
 964         [ADP5520_KEY(3, 1)]     = KEY_7,
 965         [ADP5520_KEY(2, 1)]     = KEY_8,
 966         [ADP5520_KEY(1, 1)]     = KEY_9,
 967         [ADP5520_KEY(0, 1)]     = KEY_DOT,
 968         [ADP5520_KEY(3, 0)]     = KEY_BACKSPACE,
 969         [ADP5520_KEY(2, 0)]     = KEY_0,
 970         [ADP5520_KEY(1, 0)]     = KEY_HELP,
 971         [ADP5520_KEY(0, 0)]     = KEY_ENTER,
 972 };
 973
 974 static struct adp5520_keys_platform_data adp5520_keys_data = {
 975         .rows_en_mask   = ADP5520_ROW_R3 | ADP5520_ROW_R2 | ADP5520_ROW_R1 | ADP5520_ROW_R0,
 976         .cols_en_mask   = ADP5520_COL_C3 | ADP5520_COL_C2 | ADP5520_COL_C1 | ADP5520_COL_C0,
 977         .keymap         = adp5520_keymap,
 978         .keymapsize     = ARRAY_SIZE(adp5520_keymap),
 979         .repeat         = 0,
 980 };
 981
 982         /*
 983          *  ADP5520/5501 Multifunction Device Init Data
 984          */
 985
 986 static struct adp5520_platform_data adp5520_pdev_data = {
 987         .leds = &adp5520_leds_data,
 988         .keys = &adp5520_keys_data,
 989 };
 990
 991 #endif
 992
 993 static struct i2c_board_info __initdata bfin_i2c_board_info[] = {
 994 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
 995         {
 996                 I2C_BOARD_INFO("pcf8574_lcd", 0x22),
 997         },
 998 #endif
 999 #if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
1000         {
1001                 I2C_BOARD_INFO("pcf8574_keypad", 0x27),
1002                 .irq = IRQ_PF8,
1003         },
1004 #endif
1005 #if defined(CONFIG_FB_BFIN_7393) || defined(CONFIG_FB_BFIN_7393_MODULE)
1006         {
1007                 I2C_BOARD_INFO("bfin-adv7393", 0x2B),
1008         },
1009 #endif
1010 #if defined(CONFIG_TOUCHSCREEN_AD7879_I2C) || defined(CONFIG_TOUCHSCREEN_AD7879_I2C_MODULE)
1011         {
1012                 I2C_BOARD_INFO("ad7879", 0x2C),
1013                 .irq = IRQ_PF8,
1014                 .platform_data = (void *)&bfin_ad7879_ts_info,
1015         },
1016 #endif
1017 #if defined(CONFIG_PMIC_ADP5520) || defined(CONFIG_PMIC_ADP5520_MODULE)
1018         {
1019                 I2C_BOARD_INFO("pmic-adp5520", 0x32),
1020                 .irq = IRQ_PF9,
1021                 .platform_data = (void *)&adp5520_pdev_data,
1022         },
1023 #endif
1024 #if defined(CONFIG_SND_SOC_SSM2602) || defined(CONFIG_SND_SOC_SSM2602_MODULE)
1025         {
1026                 I2C_BOARD_INFO("ssm2602", 0x1b),
1027         },
1028 #endif
1029 #if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
1030         {
1031                 I2C_BOARD_INFO("ad5252", 0x2f),
1032         },
1033 #endif
1034 #if defined(CONFIG_SND_SOC_ADAU1373) || defined(CONFIG_SND_SOC_ADAU1373_MODULE)
1035         {
1036                 I2C_BOARD_INFO("adau1373", 0x1A),
1037         },
1038 #endif
1039 };
1040
1041 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
1042 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1043 static struct resource bfin_sport0_uart_resources[] = {
1044         {
1045                 .start = SPORT0_TCR1,
1046                 .end = SPORT0_MRCS3+4,
1047                 .flags = IORESOURCE_MEM,
1048         },
1049         {
1050                 .start = IRQ_SPORT0_RX,
1051                 .end = IRQ_SPORT0_RX+1,
1052                 .flags = IORESOURCE_IRQ,
1053         },
1054         {
1055                 .start = IRQ_SPORT0_ERROR,
1056                 .end = IRQ_SPORT0_ERROR,
1057                 .flags = IORESOURCE_IRQ,
1058         },
1059 };
1060
1061 static unsigned short bfin_sport0_peripherals[] = {
1062         P_SPORT0_TFS, P_SPORT0_DTPRI, P_SPORT0_TSCLK, P_SPORT0_RFS,
1063         P_SPORT0_DRPRI, P_SPORT0_RSCLK, 0
1064 };
1065
1066 static struct platform_device bfin_sport0_uart_device = {
1067         .name = "bfin-sport-uart",
1068         .id = 0,
1069         .num_resources = ARRAY_SIZE(bfin_sport0_uart_resources),
1070         .resource = bfin_sport0_uart_resources,
1071         .dev = {
1072                 .platform_data = &bfin_sport0_peripherals, /* Passed to driver */
1073         },
1074 };
1075 #endif
1076 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1077 static struct resource bfin_sport1_uart_resources[] = {
1078         {
1079                 .start = SPORT1_TCR1,
1080                 .end = SPORT1_MRCS3+4,
1081                 .flags = IORESOURCE_MEM,
1082         },
1083         {
1084                 .start = IRQ_SPORT1_RX,
1085                 .end = IRQ_SPORT1_RX+1,
1086                 .flags = IORESOURCE_IRQ,
1087         },
1088         {
1089                 .start = IRQ_SPORT1_ERROR,
1090                 .end = IRQ_SPORT1_ERROR,
1091                 .flags = IORESOURCE_IRQ,
1092         },
1093 };
1094
1095 static unsigned short bfin_sport1_peripherals[] = {
1096         P_SPORT1_TFS, P_SPORT1_DTPRI, P_SPORT1_TSCLK, P_SPORT1_RFS,
1097         P_SPORT1_DRPRI, P_SPORT1_RSCLK, 0
1098 };
1099
1100 static struct platform_device bfin_sport1_uart_device = {
1101         .name = "bfin-sport-uart",
1102         .id = 1,
1103         .num_resources = ARRAY_SIZE(bfin_sport1_uart_resources),
1104         .resource = bfin_sport1_uart_resources,
1105         .dev = {
1106                 .platform_data = &bfin_sport1_peripherals, /* Passed to driver */
1107         },
1108 };
1109 #endif
1110 #endif
1111
1112 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
1113 #include <linux/gpio_keys.h>
1114
1115 static struct gpio_keys_button bfin_gpio_keys_table[] = {
1116         {BTN_0, GPIO_PG0, 1, "gpio-keys: BTN0"},
1117         {BTN_1, GPIO_PG13, 1, "gpio-keys: BTN1"},
1118 };
1119
1120 static struct gpio_keys_platform_data bfin_gpio_keys_data = {
1121         .buttons        = bfin_gpio_keys_table,
1122         .nbuttons       = ARRAY_SIZE(bfin_gpio_keys_table),
1123 };
1124
1125 static struct platform_device bfin_device_gpiokeys = {
1126         .name      = "gpio-keys",
1127         .dev = {
1128                 .platform_data = &bfin_gpio_keys_data,
1129         },
1130 };
1131 #endif
1132
1133 #if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
1134 #include <asm/bfin_rotary.h>
1135
1136 static struct bfin_rotary_platform_data bfin_rotary_data = {
1137         /*.rotary_up_key     = KEY_UP,*/
1138         /*.rotary_down_key   = KEY_DOWN,*/
1139         .rotary_rel_code   = REL_WHEEL,
1140         .rotary_button_key = KEY_ENTER,
1141         .debounce          = 10,        /* 0..17 */
1142         .mode              = ROT_QUAD_ENC | ROT_DEBE,
1143 };
1144
1145 static struct resource bfin_rotary_resources[] = {
1146         {
1147                 .start = IRQ_CNT,
1148                 .end = IRQ_CNT,
1149                 .flags = IORESOURCE_IRQ,
1150         },
1151 };
1152
1153 static struct platform_device bfin_rotary_device = {
1154         .name           = "bfin-rotary",
1155         .id             = -1,
1156         .num_resources  = ARRAY_SIZE(bfin_rotary_resources),
1157         .resource       = bfin_rotary_resources,
1158         .dev            = {
1159                 .platform_data = &bfin_rotary_data,
1160         },
1161 };
1162 #endif
1163
1164 static const unsigned int cclk_vlev_datasheet[] =
1165 {
1166         VRPAIR(VLEV_100, 400000000),
1167         VRPAIR(VLEV_105, 426000000),
1168         VRPAIR(VLEV_110, 500000000),
1169         VRPAIR(VLEV_115, 533000000),
1170         VRPAIR(VLEV_120, 600000000),
1171 };
1172
1173 static struct bfin_dpmc_platform_data bfin_dmpc_vreg_data = {
1174         .tuple_tab = cclk_vlev_datasheet,
1175         .tabsize = ARRAY_SIZE(cclk_vlev_datasheet),
1176         .vr_settling_time = 25 /* us */,
1177 };
1178
1179 static struct platform_device bfin_dpmc = {
1180         .name = "bfin dpmc",
1181         .dev = {
1182                 .platform_data = &bfin_dmpc_vreg_data,
1183         },
1184 };
1185
1186 static struct platform_device *stamp_devices[] __initdata = {
1187
1188         &bfin_dpmc,
1189
1190 #if defined(CONFIG_MTD_NAND_BF5XX) || defined(CONFIG_MTD_NAND_BF5XX_MODULE)
1191         &bf5xx_nand_device,
1192 #endif
1193
1194 #if defined(CONFIG_BFIN_CFPCMCIA) || defined(CONFIG_BFIN_CFPCMCIA_MODULE)
1195         &bfin_pcmcia_cf_device,
1196 #endif
1197
1198 #if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
1199         &rtc_device,
1200 #endif
1201
1202 #if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
1203         &bfin_isp1760_device,
1204 #endif
1205
1206 #if defined(CONFIG_USB_MUSB_HDRC) || defined(CONFIG_USB_MUSB_HDRC_MODULE)
1207         &musb_device,
1208 #endif
1209
1210 #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
1211         &smc91x_device,
1212 #endif
1213
1214 #if defined(CONFIG_DM9000) || defined(CONFIG_DM9000_MODULE)
1215         &dm9000_device,
1216 #endif
1217
1218 #if defined(CONFIG_BFIN_MAC) || defined(CONFIG_BFIN_MAC_MODULE)
1219         &bfin_mii_bus,
1220         &bfin_mac_device,
1221 #endif
1222
1223 #if defined(CONFIG_USB_NET2272) || defined(CONFIG_USB_NET2272_MODULE)
1224         &net2272_bfin_device,
1225 #endif
1226
1227 #if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
1228         &bfin_spi0_device,
1229 #endif
1230
1231 #if defined(CONFIG_FB_BFIN_T350MCQB) || defined(CONFIG_FB_BFIN_T350MCQB_MODULE)
1232         &bf52x_t350mcqb_device,
1233 #endif
1234
1235 #if defined(CONFIG_FB_BFIN_LQ035Q1) || defined(CONFIG_FB_BFIN_LQ035Q1_MODULE)
1236         &bfin_lq035q1_device,
1237 #endif
1238
1239 #if defined(CONFIG_SERIAL_BFIN) || defined(CONFIG_SERIAL_BFIN_MODULE)
1240 #ifdef CONFIG_SERIAL_BFIN_UART0
1241         &bfin_uart0_device,
1242 #endif
1243 #ifdef CONFIG_SERIAL_BFIN_UART1
1244         &bfin_uart1_device,
1245 #endif
1246 #endif
1247
1248 #if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
1249 #ifdef CONFIG_BFIN_SIR0
1250         &bfin_sir0_device,
1251 #endif
1252 #ifdef CONFIG_BFIN_SIR1
1253         &bfin_sir1_device,
1254 #endif
1255 #endif
1256
1257 #if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
1258         &i2c_bfin_twi_device,
1259 #endif
1260
1261 #if defined(CONFIG_SERIAL_BFIN_SPORT) || defined(CONFIG_SERIAL_BFIN_SPORT_MODULE)
1262 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1263         &bfin_sport0_uart_device,
1264 #endif
1265 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1266         &bfin_sport1_uart_device,
1267 #endif
1268 #endif
1269
1270 #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
1271         &bfin_device_gpiokeys,
1272 #endif
1273
1274 #if defined(CONFIG_INPUT_BFIN_ROTARY) || defined(CONFIG_INPUT_BFIN_ROTARY_MODULE)
1275         &bfin_rotary_device,
1276 #endif
1277
1278 #if defined(CONFIG_MTD_PHYSMAP) || defined(CONFIG_MTD_PHYSMAP_MODULE)
1279         &ezkit_flash_device,
1280 #endif
1281
1282 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE) || \
1283         defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
1284         &bfin_pcm,
1285 #endif
1286
1287 #if defined(CONFIG_SND_BF5XX_I2S) || defined(CONFIG_SND_BF5XX_I2S_MODULE)
1288         &bfin_i2s,
1289 #endif
1290
1291 #if defined(CONFIG_SND_BF5XX_TDM) || defined(CONFIG_SND_BF5XX_TDM_MODULE)
1292         &bfin_tdm,
1293 #endif
1294 };
1295
1296 static int __init ezkit_init(void)
1297 {
1298         printk(KERN_INFO "%s(): registering device resources\n", __func__);
1299         i2c_register_board_info(0, bfin_i2c_board_info,
1300                                 ARRAY_SIZE(bfin_i2c_board_info));
1301         platform_add_devices(stamp_devices, ARRAY_SIZE(stamp_devices));
1302         spi_register_board_info(bfin_spi_board_info, ARRAY_SIZE(bfin_spi_board_info));
1303         return 0;
1304 }
1305
1306 arch_initcall(ezkit_init);
1307
1308 static struct platform_device *ezkit_early_devices[] __initdata = {
1309 #if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
1310 #ifdef CONFIG_SERIAL_BFIN_UART0
1311         &bfin_uart0_device,
1312 #endif
1313 #ifdef CONFIG_SERIAL_BFIN_UART1
1314         &bfin_uart1_device,
1315 #endif
1316 #endif
1317
1318 #if defined(CONFIG_SERIAL_BFIN_SPORT_CONSOLE)
1319 #ifdef CONFIG_SERIAL_BFIN_SPORT0_UART
1320         &bfin_sport0_uart_device,
1321 #endif
1322 #ifdef CONFIG_SERIAL_BFIN_SPORT1_UART
1323         &bfin_sport1_uart_device,
1324 #endif
1325 #endif
1326 };
1327
1328 void __init native_machine_early_platform_add_devices(void)
1329 {
1330         printk(KERN_INFO "register early platform devices\n");
1331         early_platform_add_devices(ezkit_early_devices,
1332                 ARRAY_SIZE(ezkit_early_devices));
1333 }
1334
1335 void native_machine_restart(char *cmd)
1336 {
1337         /* workaround reboot hang when booting from SPI */
1338         if ((bfin_read_SYSCR() & 0x7) == 0x3)
1339                 bfin_reset_boot_spi_cs(P_DEFAULT_BOOT_SPI_CS);
1340 }
1341
1342 void bfin_get_ether_addr(char *addr)
1343 {
1344         /* the MAC is stored in OTP memory page 0xDF */
1345         u32 ret;
1346         u64 otp_mac;
1347         u32 (*otp_read)(u32 page, u32 flags, u64 *page_content) = (void *)0xEF00001A;
1348
1349         ret = otp_read(0xDF, 0x00, &otp_mac);
1350         if (!(ret & 0x1)) {
1351                 char *otp_mac_p = (char *)&otp_mac;
1352                 for (ret = 0; ret < 6; ++ret)
1353                         addr[ret] = otp_mac_p[5 - ret];
1354         }
1355 }
1356 EXPORT_SYMBOL(bfin_get_ether_addr);