arch/cris/arch-v32/drivers/Kconfig

   1 if ETRAX_ARCH_V32
   2
   3 config ETRAX_ETHERNET
   4         bool "Ethernet support"
   5         depends on ETRAX_ARCH_V32
   6         select ETHERNET
   7         select MII
   8         help
   9           This option enables the ETRAX FS built-in 10/100Mbit Ethernet
  10           controller.
  11
  12 config ETRAX_NO_PHY
  13         bool "PHY not present"
  14         depends on ETRAX_ETHERNET
  15         default N
  16         help
  17           This option disables all MDIO communication with an ethernet
  18           transceiver connected to the MII interface. This option shall
  19           typically be enabled if the MII interface is connected to a
  20           switch. This option should normally be disabled. If enabled,
  21           speed and duplex will be locked to 100 Mbit and full duplex.
  22
  23 config ETRAX_ETHERNET_IFACE0
  24         depends on ETRAX_ETHERNET
  25         bool "Enable network interface 0"
  26
  27 config ETRAX_ETHERNET_IFACE1
  28         depends on (ETRAX_ETHERNET && ETRAXFS)
  29         bool "Enable network interface 1 (uses DMA6 and DMA7)"
  30
  31 config ETRAX_ETHERNET_GBIT
  32         depends on (ETRAX_ETHERNET && CRIS_MACH_ARTPEC3)
  33         bool "Enable gigabit Ethernet support"
  34
  35 choice
  36         prompt "Eth0 led group"
  37         depends on ETRAX_ETHERNET_IFACE0
  38         default ETRAX_ETH0_USE_LEDGRP0
  39
  40 config ETRAX_ETH0_USE_LEDGRP0
  41         bool "Use LED grp 0"
  42         depends on ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO
  43         help
  44           Use LED grp 0 for eth0
  45
  46 config ETRAX_ETH0_USE_LEDGRP1
  47         bool "Use LED grp 1"
  48         depends on ETRAX_NBR_LED_GRP_TWO
  49         help
  50           Use LED grp 1 for eth0
  51
  52 config ETRAX_ETH0_USE_LEDGRPNULL
  53         bool "Use no LEDs for eth0"
  54         help
  55           Use no LEDs for eth0
  56 endchoice
  57
  58 choice
  59         prompt "Eth1 led group"
  60         depends on ETRAX_ETHERNET_IFACE1
  61         default ETRAX_ETH1_USE_LEDGRP1
  62
  63 config ETRAX_ETH1_USE_LEDGRP0
  64         bool "Use LED grp 0"
  65         depends on ETRAX_NBR_LED_GRP_ONE || ETRAX_NBR_LED_GRP_TWO
  66         help
  67           Use LED grp 0 for eth1
  68
  69 config ETRAX_ETH1_USE_LEDGRP1
  70         bool "Use LED grp 1"
  71         depends on ETRAX_NBR_LED_GRP_TWO
  72         help
  73           Use LED grp 1 for eth1
  74
  75 config ETRAX_ETH1_USE_LEDGRPNULL
  76         bool "Use no LEDs for eth1"
  77         help
  78           Use no LEDs for eth1
  79 endchoice
  80
  81 config ETRAXFS_SERIAL
  82         bool "Serial-port support"
  83         depends on ETRAX_ARCH_V32
  84         select SERIAL_CORE
  85         select SERIAL_CORE_CONSOLE
  86         help
  87           Enables the ETRAX FS serial driver for ser0 (ttyS0)
  88           You probably want this enabled.
  89
  90 config ETRAX_RS485
  91         bool "RS-485 support"
  92         depends on ETRAXFS_SERIAL
  93         help
  94           Enables support for RS-485 serial communication.
  95
  96 config ETRAX_RS485_DISABLE_RECEIVER
  97         bool "Disable serial receiver"
  98         depends on ETRAX_RS485
  99         help
 100           It is necessary to disable the serial receiver to avoid serial
 101           loopback.  Not all products are able to do this in software only.
 102
 103 config ETRAX_SERIAL_PORT0
 104         bool "Serial port 0 enabled"
 105         depends on ETRAXFS_SERIAL
 106         help
 107           Enables the ETRAX FS serial driver for ser0 (ttyS0)
 108           Normally you want this on. You can control what DMA channels to use
 109           if you do not need DMA to something else.
 110           ser0 can use dma4 or dma6 for output and dma5 or dma7 for input.
 111
 112 choice
 113         prompt "Ser0 default port type "
 114         depends on ETRAX_SERIAL_PORT0
 115         default ETRAX_SERIAL_PORT0_TYPE_232
 116         help
 117           Type of serial port.
 118
 119 config ETRAX_SERIAL_PORT0_TYPE_232
 120         bool "Ser0 is a RS-232 port"
 121         help
 122           Configure serial port 0 to be a RS-232 port.
 123
 124 config ETRAX_SERIAL_PORT0_TYPE_485HD
 125         bool "Ser0 is a half duplex RS-485 port"
 126         depends on ETRAX_RS485
 127         help
 128           Configure serial port 0 to be a half duplex (two wires) RS-485 port.
 129
 130 config ETRAX_SERIAL_PORT0_TYPE_485FD
 131         bool "Ser0 is a full duplex RS-485 port"
 132         depends on ETRAX_RS485
 133         help
 134           Configure serial port 0 to be a full duplex (four wires) RS-485 port.
 135 endchoice
 136
 137 config ETRAX_SER0_DTR_BIT
 138         string "Ser 0 DTR bit (empty = not used)"
 139         depends on ETRAX_SERIAL_PORT0
 140
 141 config ETRAX_SER0_RI_BIT
 142         string "Ser 0 RI bit (empty = not used)"
 143         depends on ETRAX_SERIAL_PORT0
 144
 145 config ETRAX_SER0_DSR_BIT
 146         string "Ser 0 DSR bit (empty = not used)"
 147         depends on ETRAX_SERIAL_PORT0
 148
 149 config ETRAX_SER0_CD_BIT
 150         string "Ser 0 CD bit (empty = not used)"
 151         depends on ETRAX_SERIAL_PORT0
 152
 153 config ETRAX_SERIAL_PORT1
 154         bool "Serial port 1 enabled"
 155         depends on ETRAXFS_SERIAL
 156         help
 157           Enables the ETRAX FS serial driver for ser1 (ttyS1).
 158
 159 choice
 160         prompt "Ser1 default port type"
 161         depends on ETRAX_SERIAL_PORT1
 162         default ETRAX_SERIAL_PORT1_TYPE_232
 163         help
 164           Type of serial port.
 165
 166 config ETRAX_SERIAL_PORT1_TYPE_232
 167         bool "Ser1 is a RS-232 port"
 168         help
 169           Configure serial port 1 to be a RS-232 port.
 170
 171 config ETRAX_SERIAL_PORT1_TYPE_485HD
 172         bool "Ser1 is a half duplex RS-485 port"
 173         depends on ETRAX_RS485
 174         help
 175           Configure serial port 1 to be a half duplex (two wires) RS-485 port.
 176
 177 config ETRAX_SERIAL_PORT1_TYPE_485FD
 178         bool "Ser1 is a full duplex RS-485 port"
 179         depends on ETRAX_RS485
 180         help
 181           Configure serial port 1 to be a full duplex (four wires) RS-485 port.
 182 endchoice
 183
 184 config ETRAX_SER1_DTR_BIT
 185         string "Ser 1 DTR bit (empty = not used)"
 186         depends on ETRAX_SERIAL_PORT1
 187
 188 config ETRAX_SER1_RI_BIT
 189         string "Ser 1 RI bit (empty = not used)"
 190         depends on ETRAX_SERIAL_PORT1
 191
 192 config ETRAX_SER1_DSR_BIT
 193         string "Ser 1 DSR bit (empty = not used)"
 194         depends on ETRAX_SERIAL_PORT1
 195
 196 config ETRAX_SER1_CD_BIT
 197         string "Ser 1 CD bit (empty = not used)"
 198         depends on ETRAX_SERIAL_PORT1
 199
 200 config ETRAX_SERIAL_PORT2
 201         bool "Serial port 2 enabled"
 202         depends on ETRAXFS_SERIAL
 203         help
 204           Enables the ETRAX FS serial driver for ser2 (ttyS2).
 205
 206 choice
 207         prompt "Ser2 default port type"
 208         depends on ETRAX_SERIAL_PORT2
 209         default ETRAX_SERIAL_PORT2_TYPE_232
 210         help
 211           What DMA channel to use for ser2
 212
 213 config ETRAX_SERIAL_PORT2_TYPE_232
 214         bool "Ser2 is a RS-232 port"
 215         help
 216           Configure serial port 2 to be a RS-232 port.
 217
 218 config ETRAX_SERIAL_PORT2_TYPE_485HD
 219         bool "Ser2 is a half duplex RS-485 port"
 220         depends on ETRAX_RS485
 221         help
 222           Configure serial port 2 to be a half duplex (two wires) RS-485 port.
 223
 224 config ETRAX_SERIAL_PORT2_TYPE_485FD
 225         bool "Ser2 is a full duplex RS-485 port"
 226         depends on ETRAX_RS485
 227         help
 228           Configure serial port 2 to be a full duplex (four wires) RS-485 port.
 229 endchoice
 230
 231
 232 config ETRAX_SER2_DTR_BIT
 233         string "Ser 2 DTR bit (empty = not used)"
 234         depends on ETRAX_SERIAL_PORT2
 235
 236 config ETRAX_SER2_RI_BIT
 237         string "Ser 2 RI bit (empty = not used)"
 238         depends on ETRAX_SERIAL_PORT2
 239
 240 config ETRAX_SER2_DSR_BIT
 241         string "Ser 2 DSR bit (empty = not used)"
 242         depends on ETRAX_SERIAL_PORT2
 243
 244 config ETRAX_SER2_CD_BIT
 245         string "Ser 2 CD bit (empty = not used)"
 246         depends on ETRAX_SERIAL_PORT2
 247
 248 config ETRAX_SERIAL_PORT3
 249         bool "Serial port 3 enabled"
 250         depends on ETRAXFS_SERIAL
 251         help
 252           Enables the ETRAX FS serial driver for ser3 (ttyS3).
 253
 254 choice
 255         prompt "Ser3 default port type"
 256         depends on ETRAX_SERIAL_PORT3
 257         default ETRAX_SERIAL_PORT3_TYPE_232
 258         help
 259           What DMA channel to use for ser3.
 260
 261 config ETRAX_SERIAL_PORT3_TYPE_232
 262         bool "Ser3 is a RS-232 port"
 263         help
 264           Configure serial port 3 to be a RS-232 port.
 265
 266 config ETRAX_SERIAL_PORT3_TYPE_485HD
 267         bool "Ser3 is a half duplex RS-485 port"
 268         depends on ETRAX_RS485
 269         help
 270           Configure serial port 3 to be a half duplex (two wires) RS-485 port.
 271
 272 config ETRAX_SERIAL_PORT3_TYPE_485FD
 273         bool "Ser3 is a full duplex RS-485 port"
 274         depends on ETRAX_RS485
 275         help
 276           Configure serial port 3 to be a full duplex (four wires) RS-485 port.
 277 endchoice
 278
 279 config ETRAX_SER3_DTR_BIT
 280         string "Ser 3 DTR bit (empty = not used)"
 281         depends on ETRAX_SERIAL_PORT3
 282
 283 config ETRAX_SER3_RI_BIT
 284         string "Ser 3 RI bit (empty = not used)"
 285         depends on ETRAX_SERIAL_PORT3
 286
 287 config ETRAX_SER3_DSR_BIT
 288         string "Ser 3 DSR bit (empty = not used)"
 289         depends on ETRAX_SERIAL_PORT3
 290
 291 config ETRAX_SER3_CD_BIT
 292         string "Ser 3 CD bit (empty = not used)"
 293         depends on ETRAX_SERIAL_PORT3
 294
 295 config ETRAX_SERIAL_PORT4
 296         bool "Serial port 4 enabled"
 297         depends on ETRAXFS_SERIAL && CRIS_MACH_ARTPEC3
 298         help
 299           Enables the ETRAX FS serial driver for ser4 (ttyS4).
 300
 301 choice
 302         prompt "Ser4 default port type"
 303         depends on ETRAX_SERIAL_PORT4
 304         default ETRAX_SERIAL_PORT4_TYPE_232
 305         help
 306           What DMA channel to use for ser4.
 307
 308 config ETRAX_SERIAL_PORT4_TYPE_232
 309         bool "Ser4 is a RS-232 port"
 310         help
 311           Configure serial port 4 to be a RS-232 port.
 312
 313 config ETRAX_SERIAL_PORT4_TYPE_485HD
 314         bool "Ser4 is a half duplex RS-485 port"
 315         depends on ETRAX_RS485
 316         help
 317           Configure serial port 4 to be a half duplex (two wires) RS-485 port.
 318
 319 config ETRAX_SERIAL_PORT4_TYPE_485FD
 320         bool "Ser4 is a full duplex RS-485 port"
 321         depends on ETRAX_RS485
 322         help
 323           Configure serial port 4 to be a full duplex (four wires) RS-485 port.
 324 endchoice
 325
 326 choice
 327         prompt "Ser4 DMA in channel "
 328         depends on ETRAX_SERIAL_PORT4
 329         default ETRAX_SERIAL_PORT4_NO_DMA_IN
 330         help
 331           What DMA channel to use for ser4.
 332
 333
 334 config ETRAX_SERIAL_PORT4_NO_DMA_IN
 335         bool "Ser4 uses no DMA for input"
 336         help
 337           Do not use DMA for ser4 input.
 338
 339 config ETRAX_SERIAL_PORT4_DMA9_IN
 340         bool "Ser4 uses DMA9 for input"
 341         depends on ETRAX_SERIAL_PORT4
 342         help
 343           Enables the DMA9 input channel for ser4 (ttyS4).
 344           If you do not enable DMA, an interrupt for each character will be
 345           used when receiving data.
 346           Normally you want to use DMA, unless you use the DMA channel for
 347           something else.
 348
 349 endchoice
 350
 351 config ETRAX_SER4_DTR_BIT
 352         string "Ser 4 DTR bit (empty = not used)"
 353         depends on ETRAX_SERIAL_PORT4
 354
 355 config ETRAX_SER4_RI_BIT
 356         string "Ser 4 RI bit (empty = not used)"
 357         depends on ETRAX_SERIAL_PORT4
 358
 359 config ETRAX_SER4_DSR_BIT
 360         string "Ser 4 DSR bit (empty = not used)"
 361         depends on ETRAX_SERIAL_PORT4
 362
 363 config ETRAX_SER4_CD_BIT
 364         string "Ser 4 CD bit (empty = not used)"
 365         depends on ETRAX_SERIAL_PORT4
 366
 367 config ETRAX_SYNCHRONOUS_SERIAL
 368         bool "Synchronous serial-port support"
 369         depends on ETRAX_ARCH_V32
 370         help
 371           Enables the ETRAX FS synchronous serial driver.
 372
 373 config ETRAX_SYNCHRONOUS_SERIAL_PORT0
 374          bool "Synchronous serial port 0 enabled"
 375          depends on ETRAX_SYNCHRONOUS_SERIAL
 376          help
 377            Enabled synchronous serial port 0.
 378
 379 config ETRAX_SYNCHRONOUS_SERIAL0_DMA
 380          bool "Enable DMA on synchronous serial port 0."
 381          depends on ETRAX_SYNCHRONOUS_SERIAL_PORT0
 382          help
 383            A synchronous serial port can run in manual or DMA mode.
 384            Selecting this option will make it run in DMA mode.
 385
 386 config ETRAX_SYNCHRONOUS_SERIAL_PORT1
 387          bool "Synchronous serial port 1 enabled"
 388          depends on ETRAX_SYNCHRONOUS_SERIAL && ETRAXFS
 389          help
 390            Enabled synchronous serial port 1.
 391
 392 config ETRAX_SYNCHRONOUS_SERIAL1_DMA
 393          bool "Enable DMA on synchronous serial port 1."
 394          depends on ETRAX_SYNCHRONOUS_SERIAL_PORT1
 395          help
 396            A synchronous serial port can run in manual or DMA mode.
 397            Selecting this option will make it run in DMA mode.
 398
 399 config ETRAX_AXISFLASHMAP
 400         bool "Axis flash-map support"
 401         depends on ETRAX_ARCH_V32
 402         select MTD
 403         select MTD_CFI
 404         select MTD_CFI_AMDSTD
 405         select MTD_JEDECPROBE
 406         select MTD_BLOCK
 407         select MTD_COMPLEX_MAPPINGS
 408         help
 409           This option enables MTD mapping of flash devices.  Needed to use
 410           flash memories.  If unsure, say Y.
 411
 412 config ETRAX_AXISFLASHMAP_MTD0WHOLE
 413         bool "MTD0 is whole boot flash device"
 414         depends on ETRAX_AXISFLASHMAP
 415         default N
 416         help
 417           When this option is not set, mtd0 refers to the first partition
 418           on the boot flash device. When set, mtd0 refers to the whole
 419           device, with mtd1 referring to the first partition etc.
 420
 421 config ETRAX_PTABLE_SECTOR
 422         int "Byte-offset of partition table sector"
 423         depends on ETRAX_AXISFLASHMAP
 424         default "65536"
 425         help
 426           Byte-offset of the partition table in the first flash chip.
 427           The default value is 64kB and should not be changed unless
 428           you know exactly what you are doing. The only valid reason
 429           for changing this is when the flash block size is bigger
 430           than 64kB (e.g. when using two parallel 16 bit flashes).
 431
 432 config ETRAX_NANDFLASH
 433         bool "NAND flash support"
 434         depends on ETRAX_ARCH_V32
 435         select MTD_NAND
 436         select MTD_NAND_IDS
 437         help
 438           This option enables MTD mapping of NAND flash devices.  Needed to use
 439           NAND flash memories.  If unsure, say Y.
 440
 441 config ETRAX_NANDBOOT
 442         bool "Boot from NAND flash"
 443         depends on ETRAX_NANDFLASH
 444         help
 445           This options enables booting from NAND flash devices.
 446           Say Y if your boot code, kernel and root file system is in
 447           NAND flash. Say N if they are in NOR flash.
 448
 449 config ETRAX_I2C
 450         bool "I2C driver"
 451         depends on ETRAX_ARCH_V32
 452         help
 453           This option enables the I2C driver used by e.g. the RTC driver.
 454
 455 config ETRAX_V32_I2C_DATA_PORT
 456         string "I2C data pin"
 457         depends on ETRAX_I2C
 458         help
 459           The pin to use for I2C data.
 460
 461 config ETRAX_V32_I2C_CLK_PORT
 462         string "I2C clock pin"
 463         depends on ETRAX_I2C
 464         help
 465           The pin to use for I2C clock.
 466
 467 config ETRAX_GPIO
 468         bool "GPIO support"
 469         depends on ETRAX_ARCH_V32
 470         ---help---
 471           Enables the ETRAX general port device (major 120, minors 0-4).
 472           You can use this driver to access the general port bits. It supports
 473           these ioctl's:
 474           #include <linux/etraxgpio.h>
 475           fd = open("/dev/gpioa", O_RDWR); // or /dev/gpiob
 476           ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_SETBITS), bits_to_set);
 477           ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_CLRBITS), bits_to_clear);
 478           err = ioctl(fd, _IO(ETRAXGPIO_IOCTYPE, IO_READ_INBITS), &val);
 479           Remember that you need to setup the port directions appropriately in
 480           the General configuration.
 481
 482 config ETRAX_VIRTUAL_GPIO
 483         bool "Virtual GPIO support"
 484         depends on ETRAX_GPIO
 485         help
 486           Enables the virtual Etrax general port device (major 120, minor 6).
 487           It uses an I/O expander for the I2C-bus.
 488
 489 config ETRAX_VIRTUAL_GPIO_INTERRUPT_PA_PIN
 490         int "Virtual GPIO interrupt pin on PA pin"
 491         range 0 7
 492         depends on ETRAX_VIRTUAL_GPIO
 493         help
 494           The pin to use on PA for virtual gpio interrupt.
 495
 496 config ETRAX_PA_CHANGEABLE_DIR
 497         hex "PA user changeable dir mask"
 498         depends on ETRAX_GPIO
 499         default "0x00" if ETRAXFS
 500         default "0x00000000" if !ETRAXFS
 501         help
 502           This is a bitmask (8 bits) with information of what bits in PA that a
 503           user can change direction on using ioctl's.
 504           Bit set = changeable.
 505           You probably want 0 here, but it depends on your hardware.
 506
 507 config ETRAX_PA_CHANGEABLE_BITS
 508         hex "PA user changeable bits mask"
 509         depends on ETRAX_GPIO
 510         default "0x00" if ETRAXFS
 511         default "0x00000000" if !ETRAXFS
 512         help
 513           This is a bitmask (8 bits) with information of what bits in PA
 514           that a user can change the value on using ioctl's.
 515           Bit set = changeable.
 516
 517 config ETRAX_PB_CHANGEABLE_DIR
 518         hex "PB user changeable dir mask"
 519         depends on ETRAX_GPIO
 520         default "0x00000" if ETRAXFS
 521         default "0x00000000" if !ETRAXFS
 522         help
 523           This is a bitmask (18 bits) with information of what bits in PB
 524           that a user can change direction on using ioctl's.
 525           Bit set = changeable.
 526           You probably want 0 here, but it depends on your hardware.
 527
 528 config ETRAX_PB_CHANGEABLE_BITS
 529         hex "PB user changeable bits mask"
 530         depends on ETRAX_GPIO
 531         default "0x00000" if ETRAXFS
 532         default "0x00000000" if !ETRAXFS
 533         help
 534           This is a bitmask (18 bits) with information of what bits in PB
 535           that a user can change the value on using ioctl's.
 536           Bit set = changeable.
 537
 538 config ETRAX_PC_CHANGEABLE_DIR
 539         hex "PC user changeable dir mask"
 540         depends on ETRAX_GPIO
 541         default "0x00000" if ETRAXFS
 542         default "0x00000000" if !ETRAXFS
 543         help
 544           This is a bitmask (18 bits) with information of what bits in PC
 545           that a user can change direction on using ioctl's.
 546           Bit set = changeable.
 547           You probably want 0 here, but it depends on your hardware.
 548
 549 config ETRAX_PC_CHANGEABLE_BITS
 550         hex "PC user changeable bits mask"
 551         depends on ETRAX_GPIO
 552         default "0x00000" if ETRAXFS
 553         default "0x00000000" if ETRAXFS
 554         help
 555           This is a bitmask (18 bits) with information of what bits in PC
 556           that a user can change the value on using ioctl's.
 557           Bit set = changeable.
 558
 559 config ETRAX_PD_CHANGEABLE_DIR
 560         hex "PD user changeable dir mask"
 561         depends on ETRAX_GPIO && ETRAXFS
 562         default "0x00000"
 563         help
 564           This is a bitmask (18 bits) with information of what bits in PD
 565           that a user can change direction on using ioctl's.
 566           Bit set = changeable.
 567           You probably want 0x00000 here, but it depends on your hardware.
 568
 569 config ETRAX_PD_CHANGEABLE_BITS
 570         hex "PD user changeable bits mask"
 571         depends on ETRAX_GPIO && ETRAXFS
 572         default "0x00000"
 573         help
 574           This is a bitmask (18 bits) with information of what bits in PD
 575           that a user can change the value on using ioctl's.
 576           Bit set = changeable.
 577
 578 config ETRAX_PE_CHANGEABLE_DIR
 579         hex "PE user changeable dir mask"
 580         depends on ETRAX_GPIO && ETRAXFS
 581         default "0x00000"
 582         help
 583           This is a bitmask (18 bits) with information of what bits in PE
 584           that a user can change direction on using ioctl's.
 585           Bit set = changeable.
 586           You probably want 0x00000 here, but it depends on your hardware.
 587
 588 config ETRAX_PE_CHANGEABLE_BITS
 589         hex "PE user changeable bits mask"
 590         depends on ETRAX_GPIO && ETRAXFS
 591         default "0x00000"
 592         help
 593           This is a bitmask (18 bits) with information of what bits in PE
 594           that a user can change the value on using ioctl's.
 595           Bit set = changeable.
 596
 597 config ETRAX_PV_CHANGEABLE_DIR
 598         hex "PV user changeable dir mask"
 599         depends on ETRAX_VIRTUAL_GPIO
 600         default "0x0000"
 601         help
 602           This is a bitmask (16 bits) with information of what bits in PV
 603           that a user can change direction on using ioctl's.
 604           Bit set = changeable.
 605           You probably want 0x0000 here, but it depends on your hardware.
 606
 607 config ETRAX_PV_CHANGEABLE_BITS
 608         hex "PV user changeable bits mask"
 609         depends on ETRAX_VIRTUAL_GPIO
 610         default "0x0000"
 611         help
 612           This is a bitmask (16 bits) with information of what bits in PV
 613           that a user can change the value on using ioctl's.
 614           Bit set = changeable.
 615
 616 config ETRAX_CARDBUS
 617         bool "Cardbus support"
 618         depends on ETRAX_ARCH_V32
 619         select HOTPLUG
 620         help
 621          Enabled the ETRAX Cardbus driver.
 622
 623 config PCI
 624        bool
 625        depends on ETRAX_CARDBUS
 626        default y
 627        select HAVE_GENERIC_DMA_COHERENT
 628
 629 config ETRAX_IOP_FW_LOAD
 630         tristate "IO-processor hotplug firmware loading support"
 631         depends on ETRAX_ARCH_V32
 632         select FW_LOADER
 633         help
 634           Enables IO-processor hotplug firmware loading support.
 635
 636 config ETRAX_STREAMCOPROC
 637         tristate "Stream co-processor driver enabled"
 638         depends on ETRAX_ARCH_V32
 639         help
 640           This option enables a driver for the stream co-processor
 641           for cryptographic operations.
 642
 643 source drivers/mmc/Kconfig
 644
 645 config ETRAX_MMC_IOP
 646         tristate "MMC/SD host driver using IO-processor"
 647         depends on ETRAX_ARCH_V32 && MMC
 648         help
 649           This option enables the SD/MMC host controller interface.
 650           The host controller is implemented using the built in
 651           IO-Processor. Only the SPU is used in this implementation.
 652
 653 config ETRAX_SPI_MMC
 654 # Make this one of several "choices" (possible simultaneously but
 655 # suggested uniquely) when an IOP driver emerges for "real" MMC/SD
 656 # protocol support.
 657         tristate
 658         depends on !ETRAX_MMC_IOP
 659         default MMC
 660         select SPI
 661         select MMC_SPI
 662         select ETRAX_SPI_MMC_BOARD
 663
 664 # For the parts that can't be a module (due to restrictions in
 665 # framework elsewhere).
 666 config ETRAX_SPI_MMC_BOARD
 667        boolean
 668        default n
 669
 670 # While the board info is MMC_SPI only, the drivers are written to be
 671 # independent of MMC_SPI, so we'll keep SPI non-dependent on the
 672 # MMC_SPI config choices (well, except for a single depends-on-line
 673 # for the board-info file until a separate non-MMC SPI board file
 674 # emerges).
 675 # FIXME: When that happens, we'll need to be able to ask for and
 676 # configure non-MMC SPI ports together with MMC_SPI ports (if multiple
 677 # SPI ports are enabled).
 678
 679 config SPI_ETRAX_SSER
 680         tristate
 681         depends on SPI_MASTER && ETRAX_ARCH_V32
 682         select SPI_BITBANG
 683         help
 684           This enables using an synchronous serial (sser) port as a
 685           SPI master controller on Axis ETRAX FS and later.  The
 686           driver can be configured to use any sser port.
 687
 688 config SPI_ETRAX_GPIO
 689         tristate
 690         depends on SPI_MASTER && ETRAX_ARCH_V32
 691         select SPI_BITBANG
 692         help
 693           This enables using GPIO pins port as a SPI master controller
 694           on Axis ETRAX FS and later.  The driver can be configured to
 695           use any GPIO pins.
 696
 697 config ETRAX_SPI_SSER0
 698         tristate "SPI using synchronous serial port 0 (sser0)"
 699         depends on ETRAX_SPI_MMC
 700         default m if MMC_SPI=m
 701         default y if MMC_SPI=y
 702         default y if MMC_SPI=n
 703         select SPI_ETRAX_SSER
 704         help
 705           Say Y for an MMC/SD socket connected to synchronous serial port 0,
 706           or for devices using the SPI protocol on that port.  Say m if you
 707           want to build it as a module, which will be named spi_crisv32_sser.
 708           (You need to select MMC separately.)
 709
 710 config ETRAX_SPI_SSER0_DMA
 711         bool "DMA for SPI on sser0 enabled"
 712         depends on ETRAX_SPI_SSER0
 713         depends on !ETRAX_SERIAL_PORT1_DMA4_OUT && !ETRAX_SERIAL_PORT1_DMA5_IN
 714         default y
 715         help
 716           Say Y if using DMA (dma4/dma5) for SPI on synchronous serial port 0.
 717
 718 config ETRAX_SPI_MMC_CD_SSER0_PIN
 719         string "MMC/SD card detect pin for SPI on sser0"
 720         depends on ETRAX_SPI_SSER0 && MMC_SPI
 721         default "pd11"
 722         help
 723           The pin to use for SD/MMC card detect.  This pin should be pulled up
 724           and grounded when a card is present.  If defined as " " (space), no
 725           pin is selected.  A card must then always be inserted for proper
 726           action.
 727
 728 config ETRAX_SPI_MMC_WP_SSER0_PIN
 729         string "MMC/SD card write-protect pin for SPI on sser0"
 730         depends on ETRAX_SPI_SSER0 && MMC_SPI
 731         default "pd10"
 732         help
 733           The pin to use for the SD/MMC write-protect signal for a memory
 734           card.  If defined as " " (space), the card is considered writable.
 735
 736 config ETRAX_SPI_SSER1
 737         tristate "SPI using synchronous serial port 1 (sser1)"
 738         depends on ETRAX_SPI_MMC
 739         default m if MMC_SPI=m && ETRAX_SPI_SSER0=n
 740         default y if MMC_SPI=y && ETRAX_SPI_SSER0=n
 741         default y if MMC_SPI=n && ETRAX_SPI_SSER0=n
 742         select SPI_ETRAX_SSER
 743         help
 744           Say Y for an MMC/SD socket connected to synchronous serial port 1,
 745           or for devices using the SPI protocol on that port.  Say m if you
 746           want to build it as a module, which will be named spi_crisv32_sser.
 747           (You need to select MMC separately.)
 748
 749 config ETRAX_SPI_SSER1_DMA
 750         bool "DMA for SPI on sser1 enabled"
 751         depends on ETRAX_SPI_SSER1 && !ETRAX_ETHERNET_IFACE1
 752         depends on !ETRAX_SERIAL_PORT0_DMA6_OUT && !ETRAX_SERIAL_PORT0_DMA7_IN
 753         default y
 754         help
 755           Say Y if using DMA (dma6/dma7) for SPI on synchronous serial port 1.
 756
 757 config ETRAX_SPI_MMC_CD_SSER1_PIN
 758         string "MMC/SD card detect pin for SPI on sser1"
 759         depends on ETRAX_SPI_SSER1 && MMC_SPI
 760         default "pd12"
 761         help
 762           The pin to use for SD/MMC card detect.  This pin should be pulled up
 763           and grounded when a card is present.  If defined as " " (space), no
 764           pin is selected.  A card must then always be inserted for proper
 765           action.
 766
 767 config ETRAX_SPI_MMC_WP_SSER1_PIN
 768         string "MMC/SD card write-protect pin for SPI on sser1"
 769         depends on ETRAX_SPI_SSER1 && MMC_SPI
 770         default "pd9"
 771         help
 772           The pin to use for the SD/MMC write-protect signal for a memory
 773           card.  If defined as " " (space), the card is considered writable.
 774
 775 config ETRAX_SPI_GPIO
 776         tristate "Bitbanged SPI using gpio pins"
 777         depends on ETRAX_SPI_MMC
 778         select SPI_ETRAX_GPIO
 779         default m if MMC_SPI=m && ETRAX_SPI_SSER0=n && ETRAX_SPI_SSER1=n
 780         default y if MMC_SPI=y && ETRAX_SPI_SSER0=n && ETRAX_SPI_SSER1=n
 781         default y if MMC_SPI=n && ETRAX_SPI_SSER0=n && ETRAX_SPI_SSER1=n
 782         help
 783           Say Y for an MMC/SD socket connected to general I/O pins (but not
 784           a complete synchronous serial ports), or for devices using the SPI
 785           protocol on general I/O pins.  Slow and slows down the system.
 786           Say m to build it as a module, which will be called spi_crisv32_gpio.
 787           (You need to select MMC separately.)
 788
 789 # The default match that of sser0, only because that's how it was tested.
 790 config ETRAX_SPI_CS_PIN
 791         string "SPI chip select pin"
 792         depends on ETRAX_SPI_GPIO
 793         default "pc3"
 794         help
 795           The pin to use for SPI chip select.
 796
 797 config ETRAX_SPI_CLK_PIN
 798         string "SPI clock pin"
 799         depends on ETRAX_SPI_GPIO
 800         default "pc1"
 801         help
 802           The pin to use for the SPI clock.
 803
 804 config ETRAX_SPI_DATAIN_PIN
 805         string "SPI MISO (data in) pin"
 806         depends on ETRAX_SPI_GPIO
 807         default "pc16"
 808         help
 809           The pin to use for SPI data in from the device.
 810
 811 config ETRAX_SPI_DATAOUT_PIN
 812         string "SPI MOSI (data out) pin"
 813         depends on ETRAX_SPI_GPIO
 814         default "pc0"
 815         help
 816           The pin to use for SPI data out to the device.
 817
 818 config ETRAX_SPI_MMC_CD_GPIO_PIN
 819         string "MMC/SD card detect pin for SPI using gpio (space for none)"
 820         depends on ETRAX_SPI_GPIO && MMC_SPI
 821         default "pd11"
 822         help
 823           The pin to use for SD/MMC card detect.  This pin should be pulled up
 824           and grounded when a card is present.  If defined as " " (space), no
 825           pin is selected.  A card must then always be inserted for proper
 826           action.
 827
 828 config ETRAX_SPI_MMC_WP_GPIO_PIN
 829         string "MMC/SD card write-protect pin for SPI using gpio (space for none)"
 830         depends on ETRAX_SPI_GPIO && MMC_SPI
 831         default "pd10"
 832         help
 833           The pin to use for the SD/MMC write-protect signal for a memory
 834           card.  If defined as " " (space), the card is considered writable.
 835
 836 # Avoid choices causing non-working configs by conditionalizing the inclusion.
 837 if ETRAX_SPI_MMC
 838 source drivers/spi/Kconfig
 839 endif
 840
 841 endif