arch/m68k/include/asm/m5249sim.h

   1 /****************************************************************************/
   2
   3 /*
   4  *      m5249sim.h -- ColdFire 5249 System Integration Module support.
   5  *
   6  *      (C) Copyright 2002, Greg Ungerer (gerg@snapgear.com)
   7  */
   8
   9 /****************************************************************************/
  10 #ifndef m5249sim_h
  11 #define m5249sim_h
  12 /****************************************************************************/
  13
  14 /*
  15  *      Define the 5249 SIM register set addresses.
  16  */
  17 #define MCFSIM_RSR              0x00            /* Reset Status reg (r/w) */
  18 #define MCFSIM_SYPCR            0x01            /* System Protection reg (r/w)*/
  19 #define MCFSIM_SWIVR            0x02            /* SW Watchdog intr reg (r/w) */
  20 #define MCFSIM_SWSR             0x03            /* SW Watchdog service (r/w) */
  21 #define MCFSIM_PAR              0x04            /* Pin Assignment reg (r/w) */
  22 #define MCFSIM_IRQPAR           0x06            /* Interrupt Assignment reg (r/w) */
  23 #define MCFSIM_MPARK            0x0C            /* BUS Master Control Reg*/
  24 #define MCFSIM_IPR              0x40            /* Interrupt Pend reg (r/w) */
  25 #define MCFSIM_IMR              0x44            /* Interrupt Mask reg (r/w) */
  26 #define MCFSIM_AVR              0x4b            /* Autovector Ctrl reg (r/w) */
  27 #define MCFSIM_ICR0             0x4c            /* Intr Ctrl reg 0 (r/w) */
  28 #define MCFSIM_ICR1             0x4d            /* Intr Ctrl reg 1 (r/w) */
  29 #define MCFSIM_ICR2             0x4e            /* Intr Ctrl reg 2 (r/w) */
  30 #define MCFSIM_ICR3             0x4f            /* Intr Ctrl reg 3 (r/w) */
  31 #define MCFSIM_ICR4             0x50            /* Intr Ctrl reg 4 (r/w) */
  32 #define MCFSIM_ICR5             0x51            /* Intr Ctrl reg 5 (r/w) */
  33 #define MCFSIM_ICR6             0x52            /* Intr Ctrl reg 6 (r/w) */
  34 #define MCFSIM_ICR7             0x53            /* Intr Ctrl reg 7 (r/w) */
  35 #define MCFSIM_ICR8             0x54            /* Intr Ctrl reg 8 (r/w) */
  36 #define MCFSIM_ICR9             0x55            /* Intr Ctrl reg 9 (r/w) */
  37 #define MCFSIM_ICR10            0x56            /* Intr Ctrl reg 10 (r/w) */
  38 #define MCFSIM_ICR11            0x57            /* Intr Ctrl reg 11 (r/w) */
  39
  40 #define MCFSIM_CSAR0            0x80            /* CS 0 Address 0 reg (r/w) */
  41 #define MCFSIM_CSMR0            0x84            /* CS 0 Mask 0 reg (r/w) */
  42 #define MCFSIM_CSCR0            0x8a            /* CS 0 Control reg (r/w) */
  43 #define MCFSIM_CSAR1            0x8c            /* CS 1 Address reg (r/w) */
  44 #define MCFSIM_CSMR1            0x90            /* CS 1 Mask reg (r/w) */
  45 #define MCFSIM_CSCR1            0x96            /* CS 1 Control reg (r/w) */
  46 #define MCFSIM_CSAR2            0x98            /* CS 2 Address reg (r/w) */
  47 #define MCFSIM_CSMR2            0x9c            /* CS 2 Mask reg (r/w) */
  48 #define MCFSIM_CSCR2            0xa2            /* CS 2 Control reg (r/w) */
  49 #define MCFSIM_CSAR3            0xa4            /* CS 3 Address reg (r/w) */
  50 #define MCFSIM_CSMR3            0xa8            /* CS 3 Mask reg (r/w) */
  51 #define MCFSIM_CSCR3            0xae            /* CS 3 Control reg (r/w) */
  52
  53 #define MCFSIM_DCR              0x100           /* DRAM Control reg (r/w) */
  54 #define MCFSIM_DACR0            0x108           /* DRAM 0 Addr and Ctrl (r/w) */
  55 #define MCFSIM_DMR0             0x10c           /* DRAM 0 Mask reg (r/w) */
  56 #define MCFSIM_DACR1            0x110           /* DRAM 1 Addr and Ctrl (r/w) */
  57 #define MCFSIM_DMR1             0x114           /* DRAM 1 Mask reg (r/w) */
  58
  59
  60 /*
  61  *      Some symbol defines for the above...
  62  */
  63 #define MCFSIM_SWDICR           MCFSIM_ICR0     /* Watchdog timer ICR */
  64 #define MCFSIM_TIMER1ICR        MCFSIM_ICR1     /* Timer 1 ICR */
  65 #define MCFSIM_TIMER2ICR        MCFSIM_ICR2     /* Timer 2 ICR */
  66 #define MCFSIM_UART1ICR         MCFSIM_ICR4     /* UART 1 ICR */
  67 #define MCFSIM_UART2ICR         MCFSIM_ICR5     /* UART 2 ICR */
  68 #define MCFSIM_DMA0ICR          MCFSIM_ICR6     /* DMA 0 ICR */
  69 #define MCFSIM_DMA1ICR          MCFSIM_ICR7     /* DMA 1 ICR */
  70 #define MCFSIM_DMA2ICR          MCFSIM_ICR8     /* DMA 2 ICR */
  71 #define MCFSIM_DMA3ICR          MCFSIM_ICR9     /* DMA 3 ICR */
  72
  73 /*
  74  *      Define system peripheral IRQ usage.
  75  */
  76 #define MCF_IRQ_TIMER           30              /* Timer0, Level 6 */
  77 #define MCF_IRQ_PROFILER        31              /* Timer1, Level 7 */
  78
  79 /*
  80  *      General purpose IO registers (in MBAR2).
  81  */
  82 #define MCFSIM2_GPIOREAD        (MCF_MBAR2 + 0x000)     /* GPIO read values */
  83 #define MCFSIM2_GPIOWRITE       (MCF_MBAR2 + 0x004)     /* GPIO write values */
  84 #define MCFSIM2_GPIOENABLE      (MCF_MBAR2 + 0x008)     /* GPIO enabled */
  85 #define MCFSIM2_GPIOFUNC        (MCF_MBAR2 + 0x00C)     /* GPIO function */
  86 #define MCFSIM2_GPIO1READ       (MCF_MBAR2 + 0x0B0)     /* GPIO1 read values */
  87 #define MCFSIM2_GPIO1WRITE      (MCF_MBAR2 + 0x0B4)     /* GPIO1 write values */
  88 #define MCFSIM2_GPIO1ENABLE     (MCF_MBAR2 + 0x0B8)     /* GPIO1 enabled */
  89 #define MCFSIM2_GPIO1FUNC       (MCF_MBAR2 + 0x0BC)     /* GPIO1 function */
  90
  91 #define MCFSIM2_GPIOINTSTAT     0xc0            /* GPIO interrupt status */
  92 #define MCFSIM2_GPIOINTCLEAR    0xc0            /* GPIO interrupt clear */
  93 #define MCFSIM2_GPIOINTENABLE   0xc4            /* GPIO interrupt enable */
  94
  95 #define MCFSIM2_INTLEVEL1       0x140           /* Interrupt level reg 1 */
  96 #define MCFSIM2_INTLEVEL2       0x144           /* Interrupt level reg 2 */
  97 #define MCFSIM2_INTLEVEL3       0x148           /* Interrupt level reg 3 */
  98 #define MCFSIM2_INTLEVEL4       0x14c           /* Interrupt level reg 4 */
  99 #define MCFSIM2_INTLEVEL5       0x150           /* Interrupt level reg 5 */
 100 #define MCFSIM2_INTLEVEL6       0x154           /* Interrupt level reg 6 */
 101 #define MCFSIM2_INTLEVEL7       0x158           /* Interrupt level reg 7 */
 102 #define MCFSIM2_INTLEVEL8       0x15c           /* Interrupt level reg 8 */
 103
 104 #define MCFSIM2_DMAROUTE        0x188           /* DMA routing */
 105
 106 #define MCFSIM2_IDECONFIG1      0x18c           /* IDEconfig1 */
 107 #define MCFSIM2_IDECONFIG2      0x190           /* IDEconfig2 */
 108
 109 /*
 110  * Define the base interrupt for the second interrupt controller.
 111  * We set it to 128, out of the way of the base interrupts, and plenty
 112  * of room for its 64 interrupts.
 113  */
 114 #define MCFINTC2_VECBASE        128
 115
 116 #define MCFINTC2_GPIOIRQ0       (MCFINTC2_VECBASE + 32)
 117 #define MCFINTC2_GPIOIRQ1       (MCFINTC2_VECBASE + 33)
 118 #define MCFINTC2_GPIOIRQ2       (MCFINTC2_VECBASE + 34)
 119 #define MCFINTC2_GPIOIRQ3       (MCFINTC2_VECBASE + 35)
 120 #define MCFINTC2_GPIOIRQ4       (MCFINTC2_VECBASE + 36)
 121 #define MCFINTC2_GPIOIRQ5       (MCFINTC2_VECBASE + 37)
 122 #define MCFINTC2_GPIOIRQ6       (MCFINTC2_VECBASE + 38)
 123 #define MCFINTC2_GPIOIRQ7       (MCFINTC2_VECBASE + 39)
 124
 125 /*
 126  * Generic GPIO support
 127  */
 128 #define MCFGPIO_PIN_MAX         64
 129 #define MCFGPIO_IRQ_MAX         -1
 130 #define MCFGPIO_IRQ_VECBASE     -1
 131
 132 /****************************************************************************/
 133
 134 #ifdef __ASSEMBLER__
 135
 136 /*
 137  *      The M5249C3 board needs a little help getting all its SIM devices
 138  *      initialized at kernel start time. dBUG doesn't set much up, so
 139  *      we need to do it manually.
 140  */
 141 .macro m5249c3_setup
 142         /*
 143          *      Set MBAR1 and MBAR2, just incase they are not set.
 144          */
 145         movel   #0x10000001,%a0
 146         movec   %a0,%MBAR                       /* map MBAR region */
 147         subql   #1,%a0                          /* get MBAR address in a0 */
 148
 149         movel   #0x80000001,%a1
 150         movec   %a1,#3086                       /* map MBAR2 region */
 151         subql   #1,%a1                          /* get MBAR2 address in a1 */
 152
 153         /*
 154          *      Move secondary interrupts to their base (128).
 155          */
 156         moveb   #MCFINTC2_VECBASE,%d0
 157         moveb   %d0,0x16b(%a1)                  /* interrupt base register */
 158
 159         /*
 160          *      Work around broken CSMR0/DRAM vector problem.
 161          */
 162         movel   #0x001F0021,%d0                 /* disable C/I bit */
 163         movel   %d0,0x84(%a0)                   /* set CSMR0 */
 164
 165         /*
 166          *      Disable the PLL firstly. (Who knows what state it is
 167          *      in here!).
 168          */
 169         movel   0x180(%a1),%d0                  /* get current PLL value */
 170         andl    #0xfffffffe,%d0                 /* PLL bypass first */
 171         movel   %d0,0x180(%a1)                  /* set PLL register */
 172         nop
 173
 174 #if CONFIG_CLOCK_FREQ == 140000000
 175         /*
 176          *      Set initial clock frequency. This assumes M5249C3 board
 177          *      is fitted with 11.2896MHz crystal. It will program the
 178          *      PLL for 140MHz. Lets go fast :-)
 179          */
 180         movel   #0x125a40f0,%d0                 /* set for 140MHz */
 181         movel   %d0,0x180(%a1)                  /* set PLL register */
 182         orl     #0x1,%d0
 183         movel   %d0,0x180(%a1)                  /* set PLL register */
 184 #endif
 185
 186         /*
 187          *      Setup CS1 for ethernet controller.
 188          *      (Setup as per M5249C3 doco).
 189          */
 190         movel  #0xe0000000,%d0                  /* CS1 mapped at 0xe0000000 */
 191         movel  %d0,0x8c(%a0)
 192         movel  #0x001f0021,%d0                  /* CS1 size of 1Mb */
 193         movel  %d0,0x90(%a0)
 194         movew  #0x0080,%d0                      /* CS1 = 16bit port, AA */
 195         movew  %d0,0x96(%a0)
 196
 197         /*
 198          *      Setup CS2 for IDE interface.
 199          */
 200         movel   #0x50000000,%d0                 /* CS2 mapped at 0x50000000 */
 201         movel   %d0,0x98(%a0)
 202         movel   #0x001f0001,%d0                 /* CS2 size of 1MB */
 203         movel   %d0,0x9c(%a0)
 204         movew   #0x0080,%d0                     /* CS2 = 16bit, TA */
 205         movew   %d0,0xa2(%a0)
 206
 207         movel   #0x00107000,%d0                 /* IDEconfig1 */
 208         movel   %d0,0x18c(%a1)
 209         movel   #0x000c0400,%d0                 /* IDEconfig2 */
 210         movel   %d0,0x190(%a1)
 211
 212         movel   #0x00080000,%d0                 /* GPIO19, IDE reset bit */
 213         orl     %d0,0xc(%a1)                    /* function GPIO19 */
 214         orl     %d0,0x8(%a1)                    /* enable GPIO19 as output */
 215         orl     %d0,0x4(%a1)                    /* de-assert IDE reset */
 216 .endm
 217
 218 #define PLATFORM_SETUP  m5249c3_setup
 219
 220 #endif /* __ASSEMBLER__ */
 221
 222 /****************************************************************************/
 223 #endif  /* m5249sim_h */