arch/mips/pmc-sierra/msp71xx/msp_serial.c

   1 /*
   2  * The setup file for serial related hardware on PMC-Sierra MSP processors.
   3  *
   4  * Copyright 2005 PMC-Sierra, Inc.
   5  *
   6  *  This program is free software; you can redistribute  it and/or modify it
   7  *  under  the terms of  the GNU General  Public License as published by the
   8  *  Free Software Foundation;  either version 2 of the  License, or (at your
   9  *  option) any later version.
  10  *
  11  *  THIS  SOFTWARE  IS PROVIDED   ``AS  IS'' AND   ANY  EXPRESS OR IMPLIED
  12  *  WARRANTIES,   INCLUDING, BUT NOT  LIMITED  TO, THE IMPLIED WARRANTIES OF
  13  *  MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.  IN
  14  *  NO  EVENT  SHALL   THE AUTHOR  BE    LIABLE FOR ANY   DIRECT, INDIRECT,
  15  *  INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
  16  *  NOT LIMITED   TO, PROCUREMENT OF  SUBSTITUTE GOODS  OR SERVICES; LOSS OF
  17  *  USE, DATA,  OR PROFITS; OR  BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
  18  *  ANY THEORY OF LIABILITY, WHETHER IN  CONTRACT, STRICT LIABILITY, OR TORT
  19  *  (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
  20  *  THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  21  *
  22  *  You should have received a copy of the  GNU General Public License along
  23  *  with this program; if not, write  to the Free Software Foundation, Inc.,
  24  *  675 Mass Ave, Cambridge, MA 02139, USA.
  25  */
  26
  27 #include <linux/serial.h>
  28 #include <linux/serial_core.h>
  29 #include <linux/serial_reg.h>
  30
  31 #include <asm/bootinfo.h>
  32 #include <asm/io.h>
  33 #include <asm/processor.h>
  34 #include <asm/serial.h>
  35 #include <linux/serial_8250.h>
  36
  37 #include <msp_prom.h>
  38 #include <msp_int.h>
  39 #include <msp_regs.h>
  40
  41 #ifdef CONFIG_KGDB
  42 /*
  43  * kgdb uses serial port 1 so the console can remain on port 0.
  44  * To use port 0 change the definition to read as follows:
  45  * #define DEBUG_PORT_BASE KSEG1ADDR(MSP_UART0_BASE)
  46  */
  47 #define DEBUG_PORT_BASE KSEG1ADDR(MSP_UART1_BASE)
  48
  49 int putDebugChar(char c)
  50 {
  51         volatile uint32_t *uart = (volatile uint32_t *)DEBUG_PORT_BASE;
  52         uint32_t val = (uint32_t)c;
  53
  54         local_irq_disable();
  55         while( !(uart[5] & 0x20) ); /* Wait for TXRDY */
  56         uart[0] = val;
  57         while( !(uart[5] & 0x20) ); /* Wait for TXRDY */
  58         local_irq_enable();
  59
  60         return 1;
  61 }
  62
  63 char getDebugChar(void)
  64 {
  65         volatile uint32_t *uart = (volatile uint32_t *)DEBUG_PORT_BASE;
  66         uint32_t val;
  67
  68         while( !(uart[5] & 0x01) ); /* Wait for RXRDY */
  69         val = uart[0];
  70
  71         return (char)val;
  72 }
  73
  74 void initDebugPort(unsigned int uartclk, unsigned int baudrate)
  75 {
  76         unsigned int baud_divisor = (uartclk + 8 * baudrate)/(16 * baudrate);
  77
  78         /* Enable FIFOs */
  79         writeb(UART_FCR_ENABLE_FIFO | UART_FCR_CLEAR_RCVR |
  80                         UART_FCR_CLEAR_XMIT | UART_FCR_TRIGGER_4,
  81                 (char *)DEBUG_PORT_BASE + (UART_FCR * 4));
  82
  83         /* Select brtc divisor */
  84         writeb(UART_LCR_DLAB, (char *)DEBUG_PORT_BASE + (UART_LCR * 4));
  85
  86         /* Store divisor lsb */
  87         writeb(baud_divisor, (char *)DEBUG_PORT_BASE + (UART_TX * 4));
  88
  89         /* Store divisor msb */
  90         writeb(baud_divisor >> 8, (char *)DEBUG_PORT_BASE + (UART_IER * 4));
  91
  92         /* Set 8N1 mode */
  93         writeb(UART_LCR_WLEN8, (char *)DEBUG_PORT_BASE + (UART_LCR * 4));
  94
  95         /* Disable flow control */
  96         writeb(0, (char *)DEBUG_PORT_BASE + (UART_MCR * 4));
  97
  98         /* Disable receive interrupt(!) */
  99         writeb(0, (char *)DEBUG_PORT_BASE + (UART_IER * 4));
 100 }
 101 #endif
 102
 103 void __init msp_serial_setup(void)
 104 {
 105         char    *s;
 106         char    *endp;
 107         struct uart_port up;
 108         unsigned int uartclk;
 109
 110         memset(&up, 0, sizeof(up));
 111
 112         /* Check if clock was specified in environment */
 113         s = prom_getenv("uartfreqhz");
 114         if(!(s && *s && (uartclk = simple_strtoul(s, &endp, 10)) && *endp == 0))
 115                 uartclk = MSP_BASE_BAUD;
 116         ppfinit("UART clock set to %d\n", uartclk);
 117
 118         /* Initialize first serial port */
 119         up.mapbase      = MSP_UART0_BASE;
 120         up.membase      = ioremap_nocache(up.mapbase,MSP_UART_REG_LEN);
 121         up.irq          = MSP_INT_UART0;
 122         up.uartclk      = uartclk;
 123         up.regshift     = 2;
 124         up.iotype       = UPIO_DWAPB; /* UPIO_MEM like */
 125         up.flags        = STD_COM_FLAGS;
 126         up.type         = PORT_16550A;
 127         up.line         = 0;
 128         up.private_data         = (void*)UART0_STATUS_REG;
 129         if (early_serial_setup(&up))
 130                 printk(KERN_ERR "Early serial init of port 0 failed\n");
 131
 132         /* Initialize the second serial port, if one exists */
 133         switch (mips_machtype) {
 134                 case MACH_MSP4200_EVAL:
 135                 case MACH_MSP4200_GW:
 136                 case MACH_MSP4200_FPGA:
 137                 case MACH_MSP7120_EVAL:
 138                 case MACH_MSP7120_GW:
 139                 case MACH_MSP7120_FPGA:
 140                         /* Enable UART1 on MSP4200 and MSP7120 */
 141                         *GPIO_CFG2_REG = 0x00002299;
 142
 143 #ifdef CONFIG_KGDB
 144                         /* Initialize UART1 for kgdb since PMON doesn't */
 145                         if( DEBUG_PORT_BASE == KSEG1ADDR(MSP_UART1_BASE) ) {
 146                                 if( mips_machtype == MACH_MSP4200_FPGA
 147                                  || mips_machtype == MACH_MSP7120_FPGA )
 148                                         initDebugPort(uartclk,19200);
 149                                 else
 150                                         initDebugPort(uartclk,57600);
 151                         }
 152 #endif
 153                         break;
 154
 155                 default:
 156                         return; /* No second serial port, good-bye. */
 157         }
 158
 159         up.mapbase      = MSP_UART1_BASE;
 160         up.membase      = ioremap_nocache(up.mapbase,MSP_UART_REG_LEN);
 161         up.irq          = MSP_INT_UART1;
 162         up.line         = 1;
 163         up.private_data         = (void*)UART1_STATUS_REG;
 164         if (early_serial_setup(&up))
 165                 printk(KERN_ERR "Early serial init of port 1 failed\n");
 166 }