arch/x86/pci/fixup.c

   1 /*
   2  * Exceptions for specific devices. Usually work-arounds for fatal design flaws.
   3  */
   4
   5 #include <linux/delay.h>
   6 #include <linux/dmi.h>
   7 #include <linux/pci.h>
   8 #include <linux/vgaarb.h>
   9 #include <asm/hpet.h>
  10 #include <asm/pci_x86.h>
  11
  12 static void pci_fixup_i450nx(struct pci_dev *d)
  13 {
  14         /*
  15          * i450NX -- Find and scan all secondary buses on all PXB's.
  16          */
  17         int pxb, reg;
  18         u8 busno, suba, subb;
  19
  20         dev_warn(&d->dev, "Searching for i450NX host bridges\n");
  21         reg = 0xd0;
  22         for(pxb = 0; pxb < 2; pxb++) {
  23                 pci_read_config_byte(d, reg++, &busno);
  24                 pci_read_config_byte(d, reg++, &suba);
  25                 pci_read_config_byte(d, reg++, &subb);
  26                 dev_dbg(&d->dev, "i450NX PXB %d: %02x/%02x/%02x\n", pxb, busno,
  27                         suba, subb);
  28                 if (busno)
  29                         pcibios_scan_root(busno);       /* Bus A */
  30                 if (suba < subb)
  31                         pcibios_scan_root(suba+1);      /* Bus B */
  32         }
  33         pcibios_last_bus = -1;
  34 }
  35 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82451NX, pci_fixup_i450nx);
  36
  37 static void pci_fixup_i450gx(struct pci_dev *d)
  38 {
  39         /*
  40          * i450GX and i450KX -- Find and scan all secondary buses.
  41          * (called separately for each PCI bridge found)
  42          */
  43         u8 busno;
  44         pci_read_config_byte(d, 0x4a, &busno);
  45         dev_info(&d->dev, "i440KX/GX host bridge; secondary bus %02x\n", busno);
  46         pcibios_scan_root(busno);
  47         pcibios_last_bus = -1;
  48 }
  49 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82454GX, pci_fixup_i450gx);
  50
  51 static void pci_fixup_umc_ide(struct pci_dev *d)
  52 {
  53         /*
  54          * UM8886BF IDE controller sets region type bits incorrectly,
  55          * therefore they look like memory despite of them being I/O.
  56          */
  57         int i;
  58
  59         dev_warn(&d->dev, "Fixing base address flags\n");
  60         for(i = 0; i < 4; i++)
  61                 d->resource[i].flags |= PCI_BASE_ADDRESS_SPACE_IO;
  62 }
  63 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_UMC, PCI_DEVICE_ID_UMC_UM8886BF, pci_fixup_umc_ide);
  64
  65 static void pci_fixup_ncr53c810(struct pci_dev *d)
  66 {
  67         /*
  68          * NCR 53C810 returns class code 0 (at least on some systems).
  69          * Fix class to be PCI_CLASS_STORAGE_SCSI
  70          */
  71         if (!d->class) {
  72                 dev_warn(&d->dev, "Fixing NCR 53C810 class code\n");
  73                 d->class = PCI_CLASS_STORAGE_SCSI << 8;
  74         }
  75 }
  76 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NCR, PCI_DEVICE_ID_NCR_53C810, pci_fixup_ncr53c810);
  77
  78 static void pci_fixup_latency(struct pci_dev *d)
  79 {
  80         /*
  81          *  SiS 5597 and 5598 chipsets require latency timer set to
  82          *  at most 32 to avoid lockups.
  83          */
  84         dev_dbg(&d->dev, "Setting max latency to 32\n");
  85         pcibios_max_latency = 32;
  86 }
  87 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5597, pci_fixup_latency);
  88 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_5598, pci_fixup_latency);
  89
  90 static void pci_fixup_piix4_acpi(struct pci_dev *d)
  91 {
  92         /*
  93          * PIIX4 ACPI device: hardwired IRQ9
  94          */
  95         d->irq = 9;
  96 }
  97 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82371AB_3, pci_fixup_piix4_acpi);
  98
  99 /*
 100  * Addresses issues with problems in the memory write queue timer in
 101  * certain VIA Northbridges.  This bugfix is per VIA's specifications,
 102  * except for the KL133/KM133: clearing bit 5 on those Northbridges seems
 103  * to trigger a bug in its integrated ProSavage video card, which
 104  * causes screen corruption.  We only clear bits 6 and 7 for that chipset,
 105  * until VIA can provide us with definitive information on why screen
 106  * corruption occurs, and what exactly those bits do.
 107  *
 108  * VIA 8363,8622,8361 Northbridges:
 109  *  - bits  5, 6, 7 at offset 0x55 need to be turned off
 110  * VIA 8367 (KT266x) Northbridges:
 111  *  - bits  5, 6, 7 at offset 0x95 need to be turned off
 112  * VIA 8363 rev 0x81/0x84 (KL133/KM133) Northbridges:
 113  *  - bits     6, 7 at offset 0x55 need to be turned off
 114  */
 115
 116 #define VIA_8363_KL133_REVISION_ID 0x81
 117 #define VIA_8363_KM133_REVISION_ID 0x84
 118
 119 static void pci_fixup_via_northbridge_bug(struct pci_dev *d)
 120 {
 121         u8 v;
 122         int where = 0x55;
 123         int mask = 0x1f; /* clear bits 5, 6, 7 by default */
 124
 125         if (d->device == PCI_DEVICE_ID_VIA_8367_0) {
 126                 /* fix pci bus latency issues resulted by NB bios error
 127                    it appears on bug free^Wreduced kt266x's bios forces
 128                    NB latency to zero */
 129                 pci_write_config_byte(d, PCI_LATENCY_TIMER, 0);
 130
 131                 where = 0x95; /* the memory write queue timer register is
 132                                 different for the KT266x's: 0x95 not 0x55 */
 133         } else if (d->device == PCI_DEVICE_ID_VIA_8363_0 &&
 134                         (d->revision == VIA_8363_KL133_REVISION_ID ||
 135                         d->revision == VIA_8363_KM133_REVISION_ID)) {
 136                         mask = 0x3f; /* clear only bits 6 and 7; clearing bit 5
 137                                         causes screen corruption on the KL133/KM133 */
 138         }
 139
 140         pci_read_config_byte(d, where, &v);
 141         if (v & ~mask) {
 142                 dev_warn(&d->dev, "Disabling VIA memory write queue (PCI ID %04x, rev %02x): [%02x] %02x & %02x -> %02x\n", \
 143                         d->device, d->revision, where, v, mask, v & mask);
 144                 v &= mask;
 145                 pci_write_config_byte(d, where, v);
 146         }
 147 }
 148 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, pci_fixup_via_northbridge_bug);
 149 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8622, pci_fixup_via_northbridge_bug);
 150 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, pci_fixup_via_northbridge_bug);
 151 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8367_0, pci_fixup_via_northbridge_bug);
 152 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8363_0, pci_fixup_via_northbridge_bug);
 153 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8622, pci_fixup_via_northbridge_bug);
 154 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8361, pci_fixup_via_northbridge_bug);
 155 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8367_0, pci_fixup_via_northbridge_bug);
 156
 157 /*
 158  * For some reasons Intel decided that certain parts of their
 159  * 815, 845 and some other chipsets must look like PCI-to-PCI bridges
 160  * while they are obviously not. The 82801 family (AA, AB, BAM/CAM,
 161  * BA/CA/DB and E) PCI bridges are actually HUB-to-PCI ones, according
 162  * to Intel terminology. These devices do forward all addresses from
 163  * system to PCI bus no matter what are their window settings, so they are
 164  * "transparent" (or subtractive decoding) from programmers point of view.
 165  */
 166 static void pci_fixup_transparent_bridge(struct pci_dev *dev)
 167 {
 168         if ((dev->device & 0xff00) == 0x2400)
 169                 dev->transparent = 1;
 170 }
 171 DECLARE_PCI_FIXUP_CLASS_HEADER(PCI_VENDOR_ID_INTEL, PCI_ANY_ID,
 172                          PCI_CLASS_BRIDGE_PCI, 8, pci_fixup_transparent_bridge);
 173
 174 /*
 175  * Fixup for C1 Halt Disconnect problem on nForce2 systems.
 176  *
 177  * From information provided by "Allen Martin" <AMartin@nvidia.com>:
 178  *
 179  * A hang is caused when the CPU generates a very fast CONNECT/HALT cycle
 180  * sequence.  Workaround is to set the SYSTEM_IDLE_TIMEOUT to 80 ns.
 181  * This allows the state-machine and timer to return to a proper state within
 182  * 80 ns of the CONNECT and probe appearing together.  Since the CPU will not
 183  * issue another HALT within 80 ns of the initial HALT, the failure condition
 184  * is avoided.
 185  */
 186 static void pci_fixup_nforce2(struct pci_dev *dev)
 187 {
 188         u32 val;
 189
 190         /*
 191          * Chip  Old value   New value
 192          * C17   0x1F0FFF01  0x1F01FF01
 193          * C18D  0x9F0FFF01  0x9F01FF01
 194          *
 195          * Northbridge chip version may be determined by
 196          * reading the PCI revision ID (0xC1 or greater is C18D).
 197          */
 198         pci_read_config_dword(dev, 0x6c, &val);
 199
 200         /*
 201          * Apply fixup if needed, but don't touch disconnect state
 202          */
 203         if ((val & 0x00FF0000) != 0x00010000) {
 204                 dev_warn(&dev->dev, "nForce2 C1 Halt Disconnect fixup\n");
 205                 pci_write_config_dword(dev, 0x6c, (val & 0xFF00FFFF) | 0x00010000);
 206         }
 207 }
 208 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2, pci_fixup_nforce2);
 209 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_NVIDIA, PCI_DEVICE_ID_NVIDIA_NFORCE2, pci_fixup_nforce2);
 210
 211 /* Max PCI Express root ports */
 212 #define MAX_PCIEROOT    6
 213 static int quirk_aspm_offset[MAX_PCIEROOT << 3];
 214
 215 #define GET_INDEX(a, b) ((((a) - PCI_DEVICE_ID_INTEL_MCH_PA) << 3) + ((b) & 7))
 216
 217 static int quirk_pcie_aspm_read(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 *value)
 218 {
 219         return raw_pci_read(pci_domain_nr(bus), bus->number,
 220                                                 devfn, where, size, value);
 221 }
 222
 223 /*
 224  * Replace the original pci bus ops for write with a new one that will filter
 225  * the request to insure ASPM cannot be enabled.
 226  */
 227 static int quirk_pcie_aspm_write(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 value)
 228 {
 229         u8 offset;
 230
 231         offset = quirk_aspm_offset[GET_INDEX(bus->self->device, devfn)];
 232
 233         if ((offset) && (where == offset))
 234                 value = value & ~PCI_EXP_LNKCTL_ASPMC;
 235
 236         return raw_pci_write(pci_domain_nr(bus), bus->number,
 237                                                 devfn, where, size, value);
 238 }
 239
 240 static struct pci_ops quirk_pcie_aspm_ops = {
 241         .read = quirk_pcie_aspm_read,
 242         .write = quirk_pcie_aspm_write,
 243 };
 244
 245 /*
 246  * Prevents PCI Express ASPM (Active State Power Management) being enabled.
 247  *
 248  * Save the register offset, where the ASPM control bits are located,
 249  * for each PCI Express device that is in the device list of
 250  * the root port in an array for fast indexing. Replace the bus ops
 251  * with the modified one.
 252  */
 253 static void pcie_rootport_aspm_quirk(struct pci_dev *pdev)
 254 {
 255         int i;
 256         struct pci_bus  *pbus;
 257         struct pci_dev *dev;
 258
 259         if ((pbus = pdev->subordinate) == NULL)
 260                 return;
 261
 262         /*
 263          * Check if the DID of pdev matches one of the six root ports. This
 264          * check is needed in the case this function is called directly by the
 265          * hot-plug driver.
 266          */
 267         if ((pdev->device < PCI_DEVICE_ID_INTEL_MCH_PA) ||
 268             (pdev->device > PCI_DEVICE_ID_INTEL_MCH_PC1))
 269                 return;
 270
 271         if (list_empty(&pbus->devices)) {
 272                 /*
 273                  * If no device is attached to the root port at power-up or
 274                  * after hot-remove, the pbus->devices is empty and this code
 275                  * will set the offsets to zero and the bus ops to parent's bus
 276                  * ops, which is unmodified.
 277                  */
 278                 for (i = GET_INDEX(pdev->device, 0); i <= GET_INDEX(pdev->device, 7); ++i)
 279                         quirk_aspm_offset[i] = 0;
 280
 281                 pci_bus_set_ops(pbus, pbus->parent->ops);
 282         } else {
 283                 /*
 284                  * If devices are attached to the root port at power-up or
 285                  * after hot-add, the code loops through the device list of
 286                  * each root port to save the register offsets and replace the
 287                  * bus ops.
 288                  */
 289                 list_for_each_entry(dev, &pbus->devices, bus_list)
 290                         /* There are 0 to 8 devices attached to this bus */
 291                         quirk_aspm_offset[GET_INDEX(pdev->device, dev->devfn)] =
 292                                 dev->pcie_cap + PCI_EXP_LNKCTL;
 293
 294                 pci_bus_set_ops(pbus, &quirk_pcie_aspm_ops);
 295                 dev_info(&pbus->dev, "writes to ASPM control bits will be ignored\n");
 296         }
 297
 298 }
 299 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,    PCI_DEVICE_ID_INTEL_MCH_PA,     pcie_rootport_aspm_quirk);
 300 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,    PCI_DEVICE_ID_INTEL_MCH_PA1,    pcie_rootport_aspm_quirk);
 301 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,    PCI_DEVICE_ID_INTEL_MCH_PB,     pcie_rootport_aspm_quirk);
 302 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,    PCI_DEVICE_ID_INTEL_MCH_PB1,    pcie_rootport_aspm_quirk);
 303 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,    PCI_DEVICE_ID_INTEL_MCH_PC,     pcie_rootport_aspm_quirk);
 304 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL,    PCI_DEVICE_ID_INTEL_MCH_PC1,    pcie_rootport_aspm_quirk);
 305
 306 /*
 307  * Fixup to mark boot BIOS video selected by BIOS before it changes
 308  *
 309  * From information provided by "Jon Smirl" <jonsmirl@gmail.com>
 310  *
 311  * The standard boot ROM sequence for an x86 machine uses the BIOS
 312  * to select an initial video card for boot display. This boot video
 313  * card will have it's BIOS copied to C0000 in system RAM.
 314  * IORESOURCE_ROM_SHADOW is used to associate the boot video
 315  * card with this copy. On laptops this copy has to be used since
 316  * the main ROM may be compressed or combined with another image.
 317  * See pci_map_rom() for use of this flag. Before marking the device
 318  * with IORESOURCE_ROM_SHADOW check if a vga_default_device is already set
 319  * by either arch cde or vga-arbitration, if so only apply the fixup to this
 320  * already determined primary video card.
 321  */
 322
 323 static void pci_fixup_video(struct pci_dev *pdev)
 324 {
 325         struct pci_dev *bridge;
 326         struct pci_bus *bus;
 327         u16 config;
 328
 329         /* Is VGA routed to us? */
 330         bus = pdev->bus;
 331         while (bus) {
 332                 bridge = bus->self;
 333
 334                 /*
 335                  * From information provided by
 336                  * "David Miller" <davem@davemloft.net>
 337                  * The bridge control register is valid for PCI header
 338                  * type BRIDGE, or CARDBUS. Host to PCI controllers use
 339                  * PCI header type NORMAL.
 340                  */
 341                 if (bridge && (pci_is_bridge(bridge))) {
 342                         pci_read_config_word(bridge, PCI_BRIDGE_CONTROL,
 343                                                 &config);
 344                         if (!(config & PCI_BRIDGE_CTL_VGA))
 345                                 return;
 346                 }
 347                 bus = bus->parent;
 348         }
 349         if (!vga_default_device() || pdev == vga_default_device()) {
 350                 pci_read_config_word(pdev, PCI_COMMAND, &config);
 351                 if (config & (PCI_COMMAND_IO | PCI_COMMAND_MEMORY)) {
 352                         pdev->resource[PCI_ROM_RESOURCE].flags |= IORESOURCE_ROM_SHADOW;
 353                         dev_printk(KERN_DEBUG, &pdev->dev, "Video device with shadowed ROM\n");
 354                 }
 355         }
 356 }
 357 DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,
 358                                 PCI_CLASS_DISPLAY_VGA, 8, pci_fixup_video);
 359
 360
 361 static const struct dmi_system_id msi_k8t_dmi_table[] = {
 362         {
 363                 .ident = "MSI-K8T-Neo2Fir",
 364                 .matches = {
 365                         DMI_MATCH(DMI_SYS_VENDOR, "MSI"),
 366                         DMI_MATCH(DMI_PRODUCT_NAME, "MS-6702E"),
 367                 },
 368         },
 369         {}
 370 };
 371
 372 /*
 373  * The AMD-Athlon64 board MSI "K8T Neo2-FIR" disables the onboard sound
 374  * card if a PCI-soundcard is added.
 375  *
 376  * The BIOS only gives options "DISABLED" and "AUTO". This code sets
 377  * the corresponding register-value to enable the soundcard.
 378  *
 379  * The soundcard is only enabled, if the mainborad is identified
 380  * via DMI-tables and the soundcard is detected to be off.
 381  */
 382 static void pci_fixup_msi_k8t_onboard_sound(struct pci_dev *dev)
 383 {
 384         unsigned char val;
 385         if (!dmi_check_system(msi_k8t_dmi_table))
 386                 return; /* only applies to MSI K8T Neo2-FIR */
 387
 388         pci_read_config_byte(dev, 0x50, &val);
 389         if (val & 0x40) {
 390                 pci_write_config_byte(dev, 0x50, val & (~0x40));
 391
 392                 /* verify the change for status output */
 393                 pci_read_config_byte(dev, 0x50, &val);
 394                 if (val & 0x40)
 395                         dev_info(&dev->dev, "Detected MSI K8T Neo2-FIR; "
 396                                         "can't enable onboard soundcard!\n");
 397                 else
 398                         dev_info(&dev->dev, "Detected MSI K8T Neo2-FIR; "
 399                                         "enabled onboard soundcard\n");
 400         }
 401 }
 402 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237,
 403                 pci_fixup_msi_k8t_onboard_sound);
 404 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8237,
 405                 pci_fixup_msi_k8t_onboard_sound);
 406
 407 /*
 408  * Some Toshiba laptops need extra code to enable their TI TSB43AB22/A.
 409  *
 410  * We pretend to bring them out of full D3 state, and restore the proper
 411  * IRQ, PCI cache line size, and BARs, otherwise the device won't function
 412  * properly.  In some cases, the device will generate an interrupt on
 413  * the wrong IRQ line, causing any devices sharing the line it's
 414  * *supposed* to use to be disabled by the kernel's IRQ debug code.
 415  */
 416 static u16 toshiba_line_size;
 417
 418 static const struct dmi_system_id toshiba_ohci1394_dmi_table[] = {
 419         {
 420                 .ident = "Toshiba PS5 based laptop",
 421                 .matches = {
 422                         DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
 423                         DMI_MATCH(DMI_PRODUCT_VERSION, "PS5"),
 424                 },
 425         },
 426         {
 427                 .ident = "Toshiba PSM4 based laptop",
 428                 .matches = {
 429                         DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
 430                         DMI_MATCH(DMI_PRODUCT_VERSION, "PSM4"),
 431                 },
 432         },
 433         {
 434                 .ident = "Toshiba A40 based laptop",
 435                 .matches = {
 436                         DMI_MATCH(DMI_SYS_VENDOR, "TOSHIBA"),
 437                         DMI_MATCH(DMI_PRODUCT_VERSION, "PSA40U"),
 438                 },
 439         },
 440         { }
 441 };
 442
 443 static void pci_pre_fixup_toshiba_ohci1394(struct pci_dev *dev)
 444 {
 445         if (!dmi_check_system(toshiba_ohci1394_dmi_table))
 446                 return; /* only applies to certain Toshibas (so far) */
 447
 448         dev->current_state = PCI_D3cold;
 449         pci_read_config_word(dev, PCI_CACHE_LINE_SIZE, &toshiba_line_size);
 450 }
 451 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_TI, 0x8032,
 452                          pci_pre_fixup_toshiba_ohci1394);
 453
 454 static void pci_post_fixup_toshiba_ohci1394(struct pci_dev *dev)
 455 {
 456         if (!dmi_check_system(toshiba_ohci1394_dmi_table))
 457                 return; /* only applies to certain Toshibas (so far) */
 458
 459         /* Restore config space on Toshiba laptops */
 460         pci_write_config_word(dev, PCI_CACHE_LINE_SIZE, toshiba_line_size);
 461         pci_read_config_byte(dev, PCI_INTERRUPT_LINE, (u8 *)&dev->irq);
 462         pci_write_config_dword(dev, PCI_BASE_ADDRESS_0,
 463                                pci_resource_start(dev, 0));
 464         pci_write_config_dword(dev, PCI_BASE_ADDRESS_1,
 465                                pci_resource_start(dev, 1));
 466 }
 467 DECLARE_PCI_FIXUP_ENABLE(PCI_VENDOR_ID_TI, 0x8032,
 468                          pci_post_fixup_toshiba_ohci1394);
 469
 470
 471 /*
 472  * Prevent the BIOS trapping accesses to the Cyrix CS5530A video device
 473  * configuration space.
 474  */
 475 static void pci_early_fixup_cyrix_5530(struct pci_dev *dev)
 476 {
 477         u8 r;
 478         /* clear 'F4 Video Configuration Trap' bit */
 479         pci_read_config_byte(dev, 0x42, &r);
 480         r &= 0xfd;
 481         pci_write_config_byte(dev, 0x42, r);
 482 }
 483 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY,
 484                         pci_early_fixup_cyrix_5530);
 485 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY,
 486                         pci_early_fixup_cyrix_5530);
 487
 488 /*
 489  * Siemens Nixdorf AG FSC Multiprocessor Interrupt Controller:
 490  * prevent update of the BAR0, which doesn't look like a normal BAR.
 491  */
 492 static void pci_siemens_interrupt_controller(struct pci_dev *dev)
 493 {
 494         dev->resource[0].flags |= IORESOURCE_PCI_FIXED;
 495 }
 496 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_SIEMENS, 0x0015,
 497                           pci_siemens_interrupt_controller);
 498
 499 /*
 500  * SB600: Disable BAR1 on device 14.0 to avoid HPET resources from
 501  * confusing the PCI engine:
 502  */
 503 static void sb600_disable_hpet_bar(struct pci_dev *dev)
 504 {
 505         u8 val;
 506
 507         /*
 508          * The SB600 and SB700 both share the same device
 509          * ID, but the PM register 0x55 does something different
 510          * for the SB700, so make sure we are dealing with the
 511          * SB600 before touching the bit:
 512          */
 513
 514         pci_read_config_byte(dev, 0x08, &val);
 515
 516         if (val < 0x2F) {
 517                 outb(0x55, 0xCD6);
 518                 val = inb(0xCD7);
 519
 520                 /* Set bit 7 in PM register 0x55 */
 521                 outb(0x55, 0xCD6);
 522                 outb(val | 0x80, 0xCD7);
 523         }
 524 }
 525 DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_ATI, 0x4385, sb600_disable_hpet_bar);
 526
 527 #ifdef CONFIG_HPET_TIMER
 528 static void sb600_hpet_quirk(struct pci_dev *dev)
 529 {
 530         struct resource *r = &dev->resource[1];
 531
 532         if (r->flags & IORESOURCE_MEM && r->start == hpet_address) {
 533                 r->flags |= IORESOURCE_PCI_FIXED;
 534                 dev_info(&dev->dev, "reg 0x14 contains HPET; making it immovable\n");
 535         }
 536 }
 537 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_ATI, 0x4385, sb600_hpet_quirk);
 538 #endif
 539
 540 /*
 541  * Twinhead H12Y needs us to block out a region otherwise we map devices
 542  * there and any access kills the box.
 543  *
 544  *   See: https://bugzilla.kernel.org/show_bug.cgi?id=10231
 545  *
 546  * Match off the LPC and svid/sdid (older kernels lose the bridge subvendor)
 547  */
 548 static void twinhead_reserve_killing_zone(struct pci_dev *dev)
 549 {
 550         if (dev->subsystem_vendor == 0x14FF && dev->subsystem_device == 0xA003) {
 551                 pr_info("Reserving memory on Twinhead H12Y\n");
 552                 request_mem_region(0xFFB00000, 0x100000, "twinhead");
 553         }
 554 }
 555 DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x27B9, twinhead_reserve_killing_zone);