Change --with-targets to --enable-targets, per GNU coding standards.

[deliverable/binutils-gdb.git] / bfd / ChangeLog

Thu Jun 23 12:53:41 1994  David J. Mackenzie  (djm@rtl.cygnus.com)

        * configure.in: Change --with-targets to --enable-targets and
        --with-64-bit-bfd to --enable-64-bit-bfd.
        * Makefile.in, mpw-make.in, targets.c: Change comments.

Wed Jun 22 17:59:59 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        * config.bfd (powerpc-*-elf*): New target, just like
        powerpc-*-sysv4*.

        * linker.c (FAIL): Undefine macro before defining as enum.

Wed Jun 22 10:52:47 1994  Ian Lance Taylor  (ian@sanguine.cygnus.com)

        * linker.c (_bfd_generic_link_add_archive_symbols): Initialize
        pass from abfd->archive_pass, and save it there as well.

        * hash.c (bfd_hash_allocate): Don't call bfd_set_error if
        obstack_alloc returns NULL unless the size is non-zero.

        * linker.c (archive_hash_allocate): Define.
        (_bfd_generic_link_add_archive_symbols): Use archive_hash_allocate
        rather than obstack_alloc, for clarity.

        * elfcode.h (elf_get_reloc_upper_bound): Correct.

        * aout64.c (BMAGIC, QMAGIC): Define if not already defined.  From
        Peter Schauer <pes@regent.e-technik.tu-muenchen.de>.

        Linux ZMAGIC support from Eric Youngdale <ericy@cais.cais.com>.
        * libaout.h (struct aoutdata): Add field zmagic_disk_block_size.
        * aout-target.h (MY(callback)): Only set alignment according to
        architecture if the section sizes are aligned to that alignment,
        for backward compatibility.
        (MY(set_sizes)): Initialize zmagic_disk_block_size field.
        * aoutx.h (adjust_z_magic): Set ztih if using q_magic_format.  Set
        text section filepos to zmagic_disk_block_size if not ztih.  Use a
        different padding algorithm if not ztih.
        * i386linux.c (MY_text_includes_header): Don't define.

        * aoutx.h (aout_link_check_ar_symbols): Just skip N_STAB and N_FN
        symbols; don't look them up in the hash table.  From
        ralphc@pyramid.com (Ralph Campbell).

Tue Jun 21 11:47:20 1994  Ian Lance Taylor  (ian@sanguine.cygnus.com)

        * coff-go32.c (go32coff_archive_p): Remove unused function.

        * section.c (bfd_abs_section): Make const.
        (bfd_abs_section_ptr, bfd_is_abs_section): Define.
        (bfd_und_section): Make const.
        (bfd_und_section_ptr, bfd_is_und_section): Define.
        (bfd_com_section): Make const.
        (bfd_com_section_ptr): Define.
        (bfd_ind_section): Make const.
        (bfd_ind_section_ptr, bfd_is_ind_section): Define.
        (bfd_abs_symbol, bfd_com_symbol): Make const.
        (bfd_und_symbol, bfd_ind_symbol): Likewise.
        (global_syms): Cast initialization of section field.
        (STD_SECTION): Define as const, and cast initializations.
        * bfd-in2.h: Rebuilt.
        * Many files: Change uses of bfd_abs_section, etc., to use
        bfd_abs_section_ptr or bfd_is_abs_section, etc.

Mon Jun 20 11:06:27 1994  Ian Lance Taylor  (ian@sanguine.cygnus.com)

        * Many files: change all bfd_target vectors to be const.  Change
        all uses of bfd_target * to be const bfd_target *.  Change
        bfd_target_vector and bfd_default_vector arrays to be const
        bfd_target * const *.

        * ecoff.c, libecoff.h, ecoffswap.h, coff-alpha.c, coff-mips.c,
        elf32-mips.c: Renamed all externally visible ECOFF routines which
        are local to BFD to start with _bfd_ecoff instead of just ecoff.

        * ecoff.c (ecoff_swap_tir_in): Change input argument to const.
        (ecoff_swap_tir_out): Likewise.
        (ecoff_swap_rndx_in, ecoff_swap_rndx_out): Likewise.
        (ecoff_slurp_symbolic_info): Add new arguments to correspond to
        read_debug_info entry point in ecoff_debug_swap structure.
        Change all calls.
        * libecoff.h (ecoff_slurp_symbolic_info): Change declaration.
        * ecoffswap.h (ecoff_swap_tir_in, ecoff_swap_tir_out): Declare.
        (ecoff_swap_rndx_in, ecoff_swap_rndx_out): Declare.
        * coff-alpha.c (alpha_ecoff_backend_data): Initialize new
        ecoff_debug_swap fields.
        * coff-mips.c (mips_ecoff_backend_data): Likewise.
        * elf32-mips.c (mips_elf_read_ecoff_info): Undefine READ.
        (mips_elf_ecoff_debug_swap): Initialize new ecoff_debug_swap
        fields.
        * configure.in (bfd_elf32_bigmips_vec): Use ecoff.o and
        ecofflink.o.
        (bfd_elf32_littlemips_vec): Likewise.
        (ecoff_big_vec, ecoff_little_vec): Likewise.
        (ecoffalpha_little_vec): Likewise.
        * Makefile.in (BFD_LIBS): Remove ecoff.o and ecofflink.o.
        (BFD32_BACKENDS): Add ecoff.o and ecofflink.o.

        * aoutx.h (NAME(aout,final_link)): Check flavour of sub, not abfd,
        when computing reloc sizes.  From Eric Youngdale
        <ericy@cais.cais.com>.
        * elfcode.h (elf_bfd_final_link): Don't try to compute maximum
        reloc count or size for a non-ELF file.

        * mipsbsd.c (MY_final_link_callback): Define to avoid warning.

        * hp300hpux.c (MY_final_link_callback): Define to avoid warning.
        (BMAGIC, QMAGIC): Define; used by aoutx.h.
        (MY(slurp_symbol_table)): Change translate_from_native_sym_flags
        calls to use new parameters.

Fri Jun 17 14:45:32 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aout-target.h (MY(callback)): Set the alignments of the text,
        data and bss sections after determining the architecture.

        * sunos.c (sunos_add_one_symbol): Treat a common symbol from a
        dynamic object as being in the .bss section of the object, rather
        than as being undefined.

Fri Jun 17 11:16:50 1994  Jeff Law  (law@snake.cs.utah.edu)

        * libhppa.h (bfd_hppa_insn2fmt, hppa_rebuild_insn): Make INLINE.

        * elf32-hppa.h (elf_hppa_final_processing): Delete decl.

Thu Jun 16 23:36:23 1994  Jeff Law  (law@snake.cs.utah.edu)

        * elfcode.h (elf_link_input_bfd): Don't try to read local symbols
        if there aren't any in the input file.

Thu Jun 16 14:25:22 1994  Eric Youngdale  (ericy@cais.cais.com)

        * i386linux.c: Many new functions and definitions for linker
        support for Linux shared libraries.
        * bfd-in.h (bfd_linux_size_dynamic_sections): Declare.
        * bfd-in2.h: Rebuild.

Thu Jun 16 14:23:46 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * config.bfd: If second argument is ``_'', then, instead of
        echoing config file name, echo whether target uses leading
        underscores on symbol names.  Add appropriate settings to
        different cases.  Used by binutils/configure.in to set default for
        c++filt.

        * elfcode.h (elf_bfd_final_link): If trying to generate a shared
        object, warn and return false.

        * aoutx.h (NAME(aout,some_aout_object_p)): Accept BMAGIC objects
        and treat them as OMAGIC.

Wed Jun 15 18:02:21 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        Enable sparc v9 support for release.  Note that this is still a
        work in progress, pending release of an ABI specification.
        * config.bfd, configure.in: Include sparc v9 elf config.
        * elfcode.h (prep_headers): Handle sparc v9 (64 bit).
        * reloc.c (bfd_reloc_code_real): New reloc types.
        * elf64-sparc.c: Implement elf64-sparc target.
        * Makefile.in, targets.c: Updated.

Wed Jun 15 01:34:07 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * libelf.h (struct elf_obj_tdata): New field dt_needed_name.
        (elf_dt_needed_name): New accessor macro.
        * elfcode.h (elf_link_add_object_symbols): If elf_dt_needed_name
        is set, use that instead of the filename for the DT_NEEDED dynamic
        entry.
        * elf.c (bfd_elf_set_dt_needed_name): New function.
        * bfd-in.h (bfd_elf_set_dt_needed_name): Declare.
        * bfd-in2.h: Rebuilt.

        * elfcode.h (NAME(bfd_elf,size_dynamic_sections)): Add sinterpptr
        argument, and set it to the .interp section.
        * bfd-in.h (bfd_elf32_size_dynamic_sections): Update prototype.
        (bfd_elf64_size_dynamic_sections): Likewise.
        * bfd-in2.h: Rebuilt.

        * coff-sparc.c (SWAP_OUT_RELOC_EXTRA): Define to clear the r_spare
        field of the reloc rather than letting it be garbage.

        * archive.c (bfd_slurp_armap): Recognize __.SYMDEF/ as well as
        __.SYMDEF; the former was used in old Linux archives.  From
        jrs@world.std.com (Rick Sladkey).

        * i386linux.c (i386linux_write_object_contents): Define; like
        MY(write_object_contents) in aout-target.h, but set MACHTYPE to
        M_386.  From jrs@world.std.com (Rick Sladkey).
        (MY_write_object_contents): Define.

        * aoutx.h (translate_from_native_sym_flags): Treat N_SETV symbols
        as N_DATA symbols.
        (aout_link_add_symbols): Likewise.

        * aoutx.h: Rewrite symbol duplicate elimination to use BFD hash
        tables.
        (struct stringtab_entry, struct stringtab_data): Remove.
        (HASHMAXLEN, HASH_CHAR, hash, compare, log2, emit_strtab): Remove.
        (struct strtab_hash_entry, struct strtab_hash): Define.
        (strtab_hash_newfunc, strtab_hash_lookup): Define.
        (stringtab_free, emit_stringtab): Define.
        (stringtab_init, add_to_stringtab): Rewrite.
        (NAME(aout,write_syms)): Use new stringtab code.
        (struct aout_final_link_info, NAME(aout,final_link)): Likewise.
        (aout_link_write_symbols, aout_link_write_other_symbol): Likewise.

        * bfd-in.h (BFD_TRADITIONAL_FORMAT): Define new BFD flag to
        request BFD to write object in the traditional format, whatever
        that means for the particular backend.
        * bfd-in2.h: Rebuilt.

        * hash.c (bfd_hash_allocate): If obstack_alloc fails, set
        bfd_error_no_memory.

Tue Jun 14 13:00:04 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * libaout.h (struct aoutdata): Add q_magic_format to subformat
        enum.
        * aout-target.h (MY_bfd_copy_private_bfd_data): Define as function
        if not already defined.  Copy subformat information.
        (MY_text_includes_header): Define as 0 if not already defined.
        (MY(backend_data)): Use MY_text_includes_header rather than 0.
        (MY_final_link_callback): Rename from final_link_callback, and
        define only if MY_final_link_callback is not already defined.
        (MY_bfd_final_link): Rename use of final_link_callback to
        MY_final_link_callback.
        * aoutx.h (NAME(aout,some_aout_object_p)): Handle QMAGIC like
        ZMAGIC, but set the subformat to q_magic_format.  Abort if the
        magic number if not recognized.
        (adjust_z_magic): Use QMAGIC if q_magic_format.
        * i386linux.c (MY_text_includes_header): Define as 1.
        (i386linux_bfd_final_link): New static function.
        (MY_bfd_final_link): Define as i386linux_bfd_final_link.

        * aoutx.h (translate_to_native_sym_flags): Check both section and
        output_section against sections of abfd.

        * libecoff.h (struct ecoff_link_hash_entry): Change type of
        written from boolean to char.  Add new field small.
        * ecoff.c (ecoff_link_hash_newfunc): Initialize written to 0
        rather than false.  Initialize small to 0.
        (ecoff_link_add_externals): If ECOFF type is scSUndefined, set
        small.  If small is set, and hash table type is common, force the
        symbol into a section named SCOMMON and change the ECOFF type from
        scCommon to scSCommon.
        (ecoff_link_write_external): Set written to 1 rather than true.
        * coff-mips.c (mips_relocate_section): Correct JMPADDR reloc
        overflow check to consider section VMA of input file.

Mon Jun 13 14:20:07 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aoutf1.h (aout_32_sunos4_write_object_contents): Handle a
        machine type of 68000.
        * aoutx.h (NAME(aout,machine_type)): Add new argument unknown.
        Set *unknown to true if machine type is really unknown, as opposed
        to M_UNKNOWN for the 68000.
        (NAME(aout,set_arch_mach)): Change NAME(aout,machine_type) call
        accordingly.
        * libaout.h (NAME(aout,machine_type)): Add new argument to
        prototype.

Sun Jun 12 20:21:03 1994  Jeff Law  (law@snake.cs.utah.edu)

        * som.c (EXEC_AUX_ID): Define based on availablity of HPUX_AUX_ID
        or HIUX_AUX_ID.
        (som_begin_writing): Use EXEC_AUX_ID instead of HPUX_AUX_ID.
        (som_write_armap): Use CPU_PA_RISC1_0 as the magic number.  Note
        som.c is careful to always define CPU_PA_RISC1_0.

Sat Jun 11 16:32:30 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Add weak symbols as an extension to a.out.
        * aoutx.h (sym_in_text_section): Don't define.
        (sym_in_data_section, sym_in_bss_section): Likewise.
        (sym_is_undefined, sym_is_global_defn): Likewise.
        (sym_is_debugger_info, sym_is_fortrancommon): Likewise.
        (sym_is_absolute, sym_is_indirect): Likewise.
        (translate_from_native_sym_flags): Rewrite for clarity.  Rearrange
        arguments and change caller.  Handle weak symbols.
        (translate_to_native_sym_flags): Likewise.
        (aout_link_check_ar_symbols): Don't ignore weak symbols.  Pull
        object in from archive if a weak defintion is found for an
        existing undefined symbol.
        (aout_link_add_symbols): Put all cases in switch.  Set flags of an
        undefined symbol to 0.  Handle weak symbols.
        (aout_link_write_symbols): Handle weak symbols.
        (aout_link_write_other_symbol): Likewise.
        (aout_link_input_section_std): Likewise.
        (aout_link_input_section_ext): Likewise.
        * sunos.c (sunos_write_dynamic_symbol): Likewise.

Fri Jun 10 13:25:13 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aoutx.h (NAME(aout,canonicalize_reloc)): Handle .bss section.
        (NAME(aout,get_reloc_upper_bound)): Likewise.

        * coff-i960.c (coff_i960_reloc_type_lookup): Add BFD_RELOC_CTOR.
        * linker.c (_bfd_generic_link_write_global_symbol): Don't assume
        the section of a common symbol is not NULL.

Wed Jun  8 23:15:53 1994  Stu Grossman  (grossman@cygnus.com)

        * nlmcode.h (nlm_object_p):  Set EXEC_P and start address for GDB.

Wed Jun  8 23:57:34 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aoutx.h (aout_get_external_symbols): Don't try to read the
        strings if there are no symbols.
        (aout_link_write_other_symbol): Use the output section when
        working out the type.

Tue Jun  7 13:25:08 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elfcode.h (assign_section_numbers): Put shstrtab, symtab and
        strtab sections at end of file.  Avoids bug in some versions of
        SVR4 strip.  From Eric Youngdale <eric@tantalus.nrl.navy.mil>.

        * coffcode.h (styp_to_sec_flags): If COFF_PAGE_SIZE is defined,
        set SEC_DEBUGGING for STYP_INFO sections.
        (coff_compute_section_file_positions): If COFF_PAGE_SIZE is
        defined, and D_PAGED is set, set the file position equal to the
        section VMA modulo COFF_PAGE_SIZE.
        * coffgen.c (coff_real_object_p): If F_EXEC is set, set D_PAGED.
        * coff-i386.c: Set D_PAGED in BFD target.
        (COFF_PAGE_SIZE): Define.
        * coff-m68k.c, coff-sparc.c: Likewise.

Mon Jun  6 10:57:28 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elfcode.h (bfd_section_from_shdr): Don't turn a reloc section
        into a BFD section just because SHF_ALLOC is set; require that it
        not use the normal symbol table.
        (elf_section_from_bfd_section): Corresponding change.

        Better indirect and warning symbol handling inspired by Stuart
        Quick <stuck@cs.man.ac.uk>.
        * linker.c (enum link_action): Add REF, MIND, CWARN, REFC.
        (link_action): Change UNDEF_ROW/def and UNDEFW_ROW/def from NOACT
        to REF.  Change UNDEF_ROW/indr and UNDEFW_ROW/indr from CYCLE to
        REFC.  Change DEF_ROW/indr and COMMON_ROW/indr from CYCLE to MDEF.
        Change DEFW_ROW/indr from CYCLE to NOACT.  Change INDR_ROW/indr
        from MDEF to MIND.  Change INDR_ROW/warn from WARNC to CYCLE.
        Change WARN_ROW/def and WARN_ROW/indr from MWARN to CWARN.  Change
        WARN_ROW/com from MWARN to WARN.  Change WARN_ROW/warn from NOACT
        to CYCLE.  Change SET_ROW/warn from WARNC to CYCLE>
        (_bfd_generic_link_add_one_symbol): Handle REF, MIND, CWARN and
        REFC.  If a new indirect symbol has been referenced, push the
        reference down to the symbol it points to.  FIx handling of WARN.
        * aoutx.h (translate_from_native_sym_flags): If N_WARNING, don't
        clobber e_type of next symbol.
        (translate_to_native_sym_flags): Likewise.
        (aout_link_write_symbols): Loop on bfd_link_hash_warning as well
        as bfd_link_hash_indirect.

        * libaout.h (struct aout_link_hash_entry): New field written.
        * aoutx.h (NAME(aout,link_hash_newfunc)): Initialize written.
        (aout_link_write_symbols): Use written, not root.written.
        (aout_link_write_other_symbol): Likewise.
        * sunos.c (sunos_scan_dynamic_symbol): Likewise.
        * libecoff.h (struct ecoff_link_hash_entry): New field written.
        * ecoff.c (ecoff_link_hash_newfunc): Initialize written.
        (ecoff_link_write_external): use written, not root.written.
        * genlink.h (struct generic_link_hash_entry): New field written.
        * linker.c (_bfd_link_hash_newfunc): Don't initialize written.
        (generic_link_hash_newfunc): Initialize written.
        (_bfd_generic_link_output_symbols): Use written, not root.written.
        (_bfd_generic_link_write_global_symbol): Likewise.
        (_bfd_generic_reloc_link_order): Likewise.

        * libecoff.h (ecoff_data_type): Add linker field.
        * ecoff.c (ecoff_write_object_contents): Check new tdata linker
        field, rather than outsymbols being non-NULL, to decide whether to
        output the symbols and relocs.
        (ecoff_bfd_final_link): Set new tdata linker field to true.

        * ecoff.c (ecoff_bfd_copy_private_bfd_data): Don't try to copy
        data to a non-ECOFF file.

        * libbfd-in.h: Add warning that libbfd.h is a generated file.
        * libbfd.h: Rebuilt.

Sun Jun  5 15:02:30 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Changes to support ELF strip and objcopy on dynamically linked
        files.
        * elfcode.h (elf_fake_sections): Add prototype.
        (bfd_section_from_shdr): Make a BFD section from an SHT_HASH
        section, and from an SHT_DYNSYM section, and from the dynamic
        string table section.
        (elf_object_p): Set D_PAGED if there is a program header.
        (elf_make_sections): Remove.
        (fix_up_strtabs): Remove.
        (elf_fake_sections): Rewrite.  Now sets sh_entsize.
        (assign_section_numbers): Rewrite.  Now sets sh_link and sh_info
        for all sections.
        (elf_compute_section_file_positions):  Don't call obsolete
        functions elf_make_sections or fix_up_strtabs.
        (swap_out_syms): Set sh_addralign to FILE_ALIGN rather than 4.
        (NAME(bfd_elf,write_object_contents)): Permit writing DYNAMIC
        objects.
        (elf_section_from_bfd_section): Treat SHT_DYNSYM like other normal
        sections.  If an SHT_REL or SHT_RELA section is allocated or uses
        an unusual symbol table, permit a BFD section to map to it.
        Permit most SHT_STRTAB sections to have a BFD section mapped to
        them.
        (elf_bfd_final_link): Don't set sh_link, sh_info or sh_entsize
        fields of dynamic sections here; do it in assign_section_numbers.
        * elf32-target.h, elf64-target.h: Add D_PAGED to permitted object
        flags.

        * elf.c (_bfd_elf_make_section_from_shdr): Only set SEC_DATA if
        SEC_LOAD is set, rather than checking SEC_ALLOC.

        * libbfd-in.h (bfd_realloc): Change last arg to "size_t size".

Fri Jun  3 10:58:02 1994  Jeff Law  (law@snake.cs.utah.edu)

        * som.c (som_write_object_contents): Don't compute the file header's
        checksum here.
        (som_write_headers): Instead do it here.

        * libbfd.h (bfd_realloc): Change last arg to "size_t size".

Thu Jun  2 17:39:22 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * hosts/sun3.h: Include <stdlib.h>.  Don't declare free, exit or
        getenv.

        Add linker support for SunOS shared libraries.
        * sunos.c: Include bfdlink.h.  Add many new functions and
        definitions for SunOS shared library support.
        * bfd-in.h (bfd_sunos_record_link_assignment): Declare.
        (bfd_sunos_size_dynamic_sections): Declare.
        * bfd-in2.h: Rebuilt.
        * aoutx.h (struct aout_link_hash_entry): Move to libaout.h.
        (struct aout_link_hash_table): Likewise.
        (aout_link_hash_lookup, aout_link_hash_traverse): Likewise.
        (aout_hash_table): Likewise.
        (NAME(aout,link_hash_newfunc)): Rename from aout_link_hash_newfunc
        and make externally visible.
        (NAME(aout,link_hash_table_init)): New function.
        (NAME(aout,link_hash_table_create)): Call
        NAME(aout,link_hash_table_init), not _bfd_link_hash_table_init.
        (aout_link_add_symbols): Don't fail if no symbols.  If it exists,
        call add_dynamic_symbols backend entry point for dynamic objects.
        Use add_one_symbol backend entry point if it exists.
        (NAME(aout,final_link)): Call finish_dynamic_link backend entry
        point, if it exists.
        (aout_link_input_bfd): For a dynamic object, call
        link_dynamic_object backend entry point, if it exists.
        (aout_link_write_other_symbol): Call write_dynamic_symbol backend
        entry point, if it exists.
        (aout_link_input_section): Don't read the relocs if they have
        already been read.
        (aout_link_input_section_std): When doing a final link, for a
        reloc against an external symbol, call check_dynamic_reloc backend
        entry point, if it exists.
        (aout_link_input_section_ext): Likewise.
        * libaout.h: Protect against multiple inclusion.  Include
        bfdlink.h.
        (struct aout_link_hash_entry): Move in from aoutx.h.
        (struct aout_link_hash_table): Likewise.
        (aout_link_hash_lookup, aout_link_hash_traverse): Likewise.
        (aout_hash_table): Likewise.
        (struct aout_backend_data): Add fields add_dynamic_symbols,
        add_one_symbol, link_dynamic_object, write_dynamic_symbol,
        check_dynamic_reloc, and finish_dynamic_link.
        (struct aout_section_data_struct): Define new structure.
        (aout_section_data): Define new accessor macro.
        (NAME(aout,link_hash_newfunc)): Declare.
        (NAME(aout,link_hash_table_init)): Declare.
        * aoutf1.h (sunos4_aout_backend): Initialize new aout_backend_data
        fields.
        * aout-target.h (MY(backend_data)): Likewise.
        * i386aout.c (MY(backend_data)): Likewise.
        * i386mach3.c (MY(backend_data)): Likewise.
        * mipsbsd.c (MY(backend_data)): Likewise.
        * sparclynx.c (sparclynx_aout_backend): Likewise.

        * aoutx.h (NAME(aout,slurp_symbol_table)): Don't zero out cached
        until we know it is non-NULL.
        (aout_link_write_symbols): Don't skip a warning symbol even if it
        has already been written out.  If skipping an indirect symbol,
        skip the next symbol as well.

Wed Jun  1 14:37:50 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * hosts/sun3.h: Don't declare qsort, malloc or realloc.

Thu May 26 13:56:03 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        * nlmcode.h (nlm_swap_auxiliary_headers_in): Cast bfd_byte pointer
        to char pointer to avoid compiler warnings.

        * dep-in.sed: Remove spaces before colons.

        Merged changes back in from FSF gas release 2.3:

        * Makefile.in (stmp-bfd.h): Wrap `if' block around grep
        invocation, to avoid a bug in BSD 4.4 make.

        From Ralph Campbell:
        * mipsbsd.c (mips_fix_jmp_addr): If symbol is undefined, return an
        error.
        (mips_fix_hi16_s): Ditto.

        Fri May 13 21:21:00 1994  DJ Delorie (dj@ctron.com)

        * makefile.dos: define a default target, or archives won't work
          due to multiple matches.

        Wed May 11 22:32:00 1994  DJ Delorie (dj@ctron.com)

        * configure.bat: update for latest files
        * makefile.dos: update for correct targets and sources
        * coff-go32.c: [new] go32's COFF format (i386coff with underscores)
        * targets.c: add go32coff target
        * makefile.in: add coff-go32.c support

Thu May 26 10:10:21 1994  Jeff Law  (law@snake.cs.utah.edu)

        * som.c (som_prep_headers): Do not set the system_id here, private
        bfd data has not been copied yet.
        (som_write_headers): Instead do it here.

Tue May 24 16:17:18 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Make MIPS ELF use new ELF backend linker.  No shared library
        support yet.
        * elf32-mips.c (bfd_mips_elf32_swap_gptab_in): New function.
        (bfd_mips_elf32_swap_gptab_out): New function.
        (mips_elf_object_p): If last symbol is LOCAL, set elf_bad_symtab.
        (mips_elf_final_write_processing): Set sh_info field for .gptab.*
        sections.
        (mips_elf_fake_sections): Set sh_entsize for .gptab.* sections.
        (mips_elf_read_ecoff_info): Read and free external symbols last,
        not first, for clarity.
        (struct mips_elf_link_hash_entry): Define new structure.
        (struct mips_elf_link_hash_table): Define new structure.
        (mips_elf_link_hash_lookup): Define new macro.
        (mips_elf_link_hash_traverse): Define new macro.
        (mips_elf_hash_table): Define new macro.
        (mips_elf_link_hash_newfunc): New static function.
        (mips_elf_link_hash_table_create): New static function.
        (mips_elf_add_symbol_hook): New static function.
        (struct extsym_info): Define new structure.
        (mips_elf_get_extr, mips_elf_set_index): Remove.
        (mips_elf_output_extsym): New static function.
        (gptab_compare): New static function.
        (mips_elf_final_link): Rewrite to use ELF backend linker, and to
        merge gptab information in input files.
        (mips_elf_relocate_hi16): New static function.
        (mips_elf_relocate_section): New static function.
        (bfd_elf32_bfd_link_hash_table_create): Define as macro before
        including elf32-target.h.
        (elf_backend_relocate_section): Likewise.
        (elf_backend_add_symbol_hook): Likewise.
        * elf.c (_bfd_elf_link_hash_newfunc): Rename from
        elf_link_hash_newfunc and make globally visible.  Change caller.
        (_bfd_elf_link_hash_table_init): New function, broken out of
        _bfd_elf_link_hash_table_create.
        (_bfd_elf_link_hash_table_create): Use
        _bfd_elf_link_hash_table_init.
        * libelf.h (struct elf_obj_tdata): Add new field bad_symtab.
        (elf_bad_symtab): Define new accessor macro.
        (_bfd_elf_link_hash_newfunc): Declare.
        (_bew_elf_link_hash_table_init): Declare.
        * elfcode.h (elf_object_p): Call backend object_p hook after
        swapping in all the section headers.
        (map_program_segments): Correct typo: Internal for External.
        (elf_link_add_object_symbols): If elf_bad_symtab is set, read all
        the symbols.  Skip STB_LOCAL symbols rather than giving an error.
        (elf_bfd_final_link): If elf_bad_symtab is set, allocate space for
        all symbols, not just locals.
        (elf_link_output_extsym): Only skip a symbol not mentioned by a
        regular file if it is mentioned by a dynamic object.
        (elf_link_input_bfd): If elf_bad_symtab is set, read all the
        symbols.

Fri May 20 13:38:23 1994  Jeff Law  (law@snake.cs.utah.edu)

        * som.c (som_set_reloc_info): Do not set any relocation info
        for SOM fixups which are never passed to BFD.

Fri May 20 11:57:05 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * coff-mips.c (mips_relocate_section): Add MIPS_R_JMPADDR overflow
        checking.

        * elf32-i386.c (elf_i386_size_dynamic_sections): Add DT_DEBUG to
        the dynamic linking information for the benefit of the debugger.
        From Peter Schauer.
        * elf32-sparc.c (elf32_sparc_size_dynamic_sections): Likewise.

        * elf.c (_bfd_elf_make_section_from_shdr): New function, based on
        code repeated three times in bfd_section_from_shdr in elfcode.h.
        * libelf.h (_bfd_elf_make_section_from_shdr): Declare.
        * elfcode.h (bfd_section_from_shdr): Use new function
        _bfd_elf_make_section_from_shdr to create BFD sections.  If a
        reloc section does not use the main symbol table, or it is part of
        the process image, treat it as a normal section, not relocs.
        * elf32-mips.c (mips_elf_section_from_shdr): Use new function
        _bfd_elf_make_section_from_shdr.

Thu May 19 11:37:11 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elf32-target.h, elf64-target.h: Change ar_max_namelen value from
        15 to 14 to match SVR4 ar.

        Add support for ELF shared libraries.  Loosely based on work by
        Eric Youngdale <ericy@cais.com>.
        * libelf.h (struct elf_backend_data): Add new fields for dynamic
        linking: elf_backend_create_dynamic_sections,
        elf_backend_adjust_dynamic_symbol,
        elf_backend_size_dynamic_sections,
        elf_backend_finish_dynamic_symbol,
        elf_backend_finish_dynamic_sections.
        (struct elf_link_hash_entry): Change type of align field to
        bfd_size_type.  Add fields dynindx, dynstr_index, weakdef,
        elf_link_hash_flags.
        (struct elf_link_hash_table): Add fields dynobj, dynsymcount,
        dynstr, bucketcount.
        (bfd_elf32_swap_reloc_in, bfd_elf32_swap_reloc_out): Declare.
        (bfd_elf32_swap_reloca_in, bfd_elf32_swap_reloca_out): Declare.
        (bfd_elf32_swap_dyn_in, bfd_elf32_swap_dyn_out): Declare.
        (bfd_elf32_add_dynamic_entry): Declare.
        (bfd_elf64_swap_reloc_in, bfd_elf64_swap_reloc_out): Declare.
        (bfd_elf64_swap_reloca_in, bfd_elf64_swap_reloca_out): Declare.
        (bfd_elf64_swap_dyn_in, bfd_elf64_swap_dyn_out): Declare.
        (bfd_elf64_add_dynamic_entry): Declare.
        * elfcode.h (Elf_External_Dyn): Define.
        (elf_swap_reloc_in): Define as macro using NAME.  Make externally
        visible.
        (elf_swap_reloc_out): Likewise.
        (elf_swap_reloca_in, elf_swap_reloca_out): Likewise.
        (elf_swap_dyn_in, elf_swap_dyn_out): Define as macro using NAME
        and as new externally visible function.
        (elf_fake_sections): Set section type of dynamic sections based on
        section names.
        (elf_write_phdrs): Remove.
        (assign_file_position_for_section): Add new align argument.
        Change all callers.
        (get_program_header_size): New static function.
        (struct seg_info): Remove.
        (map_program_segments): Completely rewrite.
        (assign_file_positions_except_relocs): Completely rewrite.
        (assign_file_positions_for_relocs): Don't set a file position for
        sections which already have one.  Don't bother to align the file
        position here.
        (section_from_elf_index): Handle SHT_HASH and SHT_DYNAMIC
        section types.
        (elf_section_from_bfd_section): Likewise.
        (elf_slurp_symbol_table): If section_from_elf_index fails, just
        use bfd_abs_section rather than returning an error.
        (elf_sizeof_headers): Make useful.
        (elf_link_record_dynamic_symbol): New static function.
        (elf_link_add_object_symbols): Handle dynamic objects.
        (elf_link_create_dynamic_sections): New static function.
        (elf_add_dynamic_entry): Define as macro using NAME and as new
        externally visible function.
        (NAME(bfd_elf,record_link_assignment)): New function.
        (elf_buckets): New static variable.
        (NAME(bfd_elf,size_dynamic_sections)): New function.
        (struct elf_final_link_info): Add dynsym_sec and hash_sec fields.
        (elf_bfd_final_link): Handle dynamic linking.  Create a section
        symbol for all ELF sections, not all BFD sections.  Store section
        symbol index in target_index field, not index field.  Traverse
        over global symbols even if stripping.
        (elf_link_output_extsym): Output dynamic symbols.  Mark symbols
        defined by dynamic objects as undefined.
        (elf_link_input_bfd): Ignore dynamic objects.  Use target_index
        field for section relocs, and make sure it is set.
        (elf_reloc_link_order): Use target_index field for section relocs,
        and make sure it is set.
        * elf.c (elf_link_hash_newfunc): Initialize dynindx, dynstr_index,
        weakdef and elf_link_hash_flags fields.
        (_bfd_elf_link_hash_table_create): Initialize dynobj, dynsymcount,
        dynstr and bucketcount fields.
        * elf32-target.h: Initialize new dynamic linking fields.
        * elf64-target.h: Likewise.  
        * elf32-i386.c: New functions for dynamic linking support.
        * elf32-sparc.c: Likewise.
        * bfd-in.h (bfd_elf32_record_link_assignment): Declare.
        (bfd_elf64_record_link_assignment): Declare.
        (bfd_elf32_size_dynamic_sections): Declare.
        (bfd_elf64_size_dynamic_sections): Declare.
        * bfd-in2.h: Rebuilt.

Wed May 18 08:29:04 1994  Ian Lance Taylor  (ian@cygnus.com)

        * som.c: Don't include <sys/dir.h> or <sys/user.h>.
        (som_reloc_queue_find): Call memcmp instead of bcmp.
        (som_bfd_reloc_type_lookup): Change first argument to bfd *.
        (compare_syms): Change types of arguments to const void *.
        (bfd_section_from_som_symbol): Removed unused local found.
        (som_write_armap): Add elength, map, orl_count and int arguments.
        (som_write_armap): Use %ld and cast to long for getuid result.

Wed May 18 09:09:32 1994  Jeff Law  (law@snake.cs.utah.edu)

        * elf32-hppa.h (R_HPPA_ABS_CALL): Define.
        * elf32-hppa.c (hppa_elf_gen_reloc_type): Handle absolute calls.

        * som.h (R_HPPA_ABS_CALL): Define.
        * som.c (hppa_som_gen_reloc_type): Delete complex relocation types.

Tue May 17 19:33:12 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        * coff-i960.c (icoff_little_vec, icoff_big_vec): Indicate leading
        underscore, for compatibility with Intel tool chain (gnu960v2).

Mon May 16 10:09:22 1994  Jeff Law  (law@snake.cs.utah.edu)

        * bfd-in2.h: Rebuilt.

        * elf32-hppa.c: Change .hppa_linker_stubs to .PARISC.stubs,
        likewise for other PA specific sections.
        (hppa_elf_relocate_unwind_table): Delete unused
        function.
        (elf_hppa_howto_table): Completely new table based on 94-02-02
        draft PA ELF spec.  Change relocation tags appropriately
        throughout elf32-hppa.c
        (hppa_elf_gen_reloc_type): Rewrite and simplify based on 94-02-02
        spec.
        (hppa_elf_reloc): Likewise.
        (hppa_look_for_stubs_in_section): Likewise
        (ELF_MACHINE_CODE): Change to EM_PARISC.
        * elf32-hppa.h: Include "elf/hppa.h".  Change relocation tags 
        appropriately throughout elf32-hppa.h.
        (elf32_hppa_reloc_type): New table based on 94-02-02 draft PA ELF
        spec.
        (R_HPPA_ABS_CALL, R_HPPA_COMPLEX*, R_HPPA_UNWIND): Delete definitions.
        * elfcode.h (prep_headers): Use EM_PARISC instead of EM_HPPA.
        * reloc.c (bfd_reloc_code_real): Delete unused HPPA relocations.
        * som.h (R_HPPA_ABS_CALL, R_HPPA_COMPLEX): Delete definitions.

        * libhppa.h (hppa_field_adjust): Avoid adding constant_value into
        the final value twice for LR and RR field selectors.

Sat May 14 09:09:19 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * aoutx.h (add_to_stringtab): Use BFD_ASSERT not assert.  This
        avoids __eprintf troubles.

Fri May 13 10:51:21 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * bout.c (b_out_bfd_reloc_type_lookup): Handle BFD_RELOC_CTOR.

        * config/mipsbelf.mt (SELECT_VECS): Add ecoff_big_vec and
        ecoff_little_vec since Irix 5 supports ECOFF executables.

Wed May 11 00:31:57 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * ecoff.c (ecoff_find_nearest_line): Handle fdr.adr != pdr.adr
        correctly.

        * Makefile.in (stmp-bfd.h): Use || instead of ; to force SunOS
        make to invoke the shell.

Tue May 10 14:23:43 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * section.c (SEC_COFF_SHARED_LIBRARY): Renamed from
        SEC_SHARED_LIBRARY for clarity.  Changed all uses.
        * bfd-in2.h: Rebuilt.
        * coffcode.h (sec_to_styp_flags): If SEC_COFF_SHARED_LIBRARY is
        set, set STYP_NOLOAD.
        * coffgen.c (coff_section_from_bfd_index): Don't get an assertion
        failure because of a bad shared library.

Mon May  9 18:53:40 1994  Bill Cox  (bill@rtl.cygnus.com)

        * linker.c: Add missing comment terminator.

Mon May  9 11:53:54 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * linker.c (_bfd_generic_link_add_one_symbol): If hashp and *hashp
        are not NULL, assume the caller has already looked up the symbol
        in the hash table and has stored the entry in *hashp.
        (generic_link_add_symbol_list): Set h to NULL before calling
        _bfd_generic_link_add_one_symbol.
        * ecoff.c (ecoff_link_add_externals): Likewise.

        * elfcode.h (assign_file_positions_except_relocs): Don't require
        page shared between .data and .bss segments to contain zeroes.

        * elfcode.h: Include bfdlink.h.  Added several new functions to do
        linking.
        (ELF_R_TYPE): Define.
        (bfd_add_to_strtab): Return unsigned long.  Change check for
        realloc failure.
        (elf_fake_sections): Check return value of bfd_add_to_strtab.
        (elf_compute_section_file_positions): Add link_info argument.
        Call elf_backend_begin_write_processing hook and prep_headers
        here.  Only call swap_out_syms if link_info is NULL.  Set up
        .shstrtab section here.  Pass dosyms argument to
        assign_file_positions_except_relocs.  Set output_has_begun flag.
        (assign_file_positions_for_symtab_and_strtabs): Add dosyms
        argument, and use it to control setting .symtab and .strtab file
        positions.
        (assign_file_positions_except_relocs): Add dosyms argument, and
        pass it on.
        (prep_headers): Check return value of bfd_add_to_strtab.
        (swap_out_syms): Likewise.  Also, don't set up .shstrtab here.
        (NAME(bfd_elf,write_object_contents)): Some calls moved into
        elf_compute_section_file_positions.
        (elf_set_section_contents): Likewise.
        (elf_slurp_symbol_table): SHN_LORESERV corrected to SHN_LORESERVE.
        * libelf.h: Include bfdlink.h.
        (struct elf_backend_data): Add fields collect,
        elf_add_symbol_hook, elf_backend_relocate_section.
        (struct bfd_elf_section_data): Add field rel_hashes.
        (struct elf_obj_tdata): Remove fields internal_syms and symbols.
        Add field sym_hashes.
        (obj_symbols, obj_internal_syms): Remove definitions.
        (elf_sym_hashes): Define.
        (struct elf_link_hash_entry): Define.
        (struct elf_link_hash_table): Define.
        (elf_link_hash_lookup): Define.
        (elf_link_hash_traverse): Define.
        (elf_hash_table): Define.
        (_bfd_elf_link_hash_table_create): Declare.
        (bfd_elf32_bfd_link_add_symbols): Declare.
        (bfd_elf32_bfd_final_link): Declare.
        (bfd_elf64_bfd_link_add_symbols): Declare.
        (bfd_elf64_bfd_final_link): Declare.
        * elf.c: Include bfdlink.h.
        (elf_link_hash_newfunc): New function.
        (_bfd_elf_link_hash_table_create): New function.
        * elf32-target.h (elf_backend_relocate_section): If not defined,
        define as 0 and use generic linker.  Otherwise, use ELF backend
        linker.
        (elf_backend_collect): If not defined, define as false.
        (elf_backend_add_symbol_hook): If not defined, define as 0.
        (elf32_bed): Initialize new fields.
        * elf64-target.h: Same changes as elf32-target.h.
        * elf32-i386.c: Include bfdlink.h.
        (elf_i386_relocate_section): New function.
        (elf_backend_relocate_section): Define.
        * elf32-sparc.c: Include bfdlink.h.
        (elf_info_to_howto): Change type of dst from Elf32_Internal_Rela
        to Elf_Internal_Rela (they're the same type anyhow).
        (elf_sparc_relocate_section): New function.
        (elf_backend_relocate_section): Define.
        * elf32-mips.c (elf_backend_collect): Define.

        * Makefile.in (stmp-bfd.h): Avoid useless make error message in a
        different way; touch takes a numeric argument on some systems.

Fri May  6 13:34:14 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * nlmcode.h (nlm_swap_auxiliary_headers_in): Rework custom header
        handling for latest suggested format.
        (nlm_swap_auxiliary_headers_out): Likewise.
        (nlm_compute_section_file_positions): Likewise.

Fri May  6 11:11:50 1994  D. V. Henkel-Wallace  (gumby@rtl.cygnus.com)

        * config.bfd: handle erricsson config (for OSE).

Thu May  5 15:40:47 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        Patches from Ralph Campbell:
        * mipsbsd.c (mips_fix_jmp_addr): New function.
        (mips_fix_hi16_s): Use bfd_is_com_section.
        (mips_howto_table_ext): Call mips_fix_jmp_addr for MIPS_RELOC_JMP.

Fri May  6 11:48:55 1994  Steve Chamberlain  (sac@cygnus.com)

        * config/go32.mh: XX support.

        From bill
        * Makefile.in: Build sysdep.h without causing worrying but
        harmless error message.

Wed May  4 11:09:53 1994  Ian Lance Taylor  (ian@cygnus.com)

        Changed m68k-aout to set flags to 0; m68k-sunos still uses 1.
        * aout0.c: New file.
        * targets.c (aout0_big_vec): Declare.
        (bfd_target_vector): Add aout0_big_vec.
        * config.bfd (m68*-*-aout*): Use m68k-0aout, not m68k-aout.
        * config/m68k-aout.mt (SELECT_VECS): Removed.
        * config/m68k-0aout.mt: New file.
        * configure.in (aout0_big_vec): New target vector: use aout0.o,
        aout32.o and stab-syms.o.
        * Makefile.in: Rebuilt dependencies.
        (BFD32_BACKENDS): Add aout0.o.
        (CFILES): Add aout0.c.

        * libaout.h (struct aout_backend_data): Add field exec_hdr_flags.
        * aout-target.h (MY_exec_hdr_flags): If not defined, define as 0.
        MY(backend_data): Initialize exec_hdr_flags field.
        * aoutf1.h (sunos_32_set_arch_mach): Make static.
        (aout32_sunos4_write_object_contents): Set flags from backend
        info.
        (MY_exec_hdr_flags): If not defined, define as 1.
        (sunos4_aout_backend): Initialize exec_hdr_flags field.
        * aout-encap.c (encap_write_object_contents): Set flags from
        backend info.
        (MY_exec_hdr_flags): Define as N_FLAGS_COFF_ENCAPSULATE.
        * hp300hpux.c (MY_exec_hdr_flags): Define as 0x2.
        (MY(write_object_contents)): Set flags from backend info.
        * i386aout.c (MY(backend_data)): Initialize exec_hdr_flags field.
        * i386mach3.c (MY(backend_data)): Likewise.
        * mipsbsd.c (MY(backend_data)): Likewise.
        * sparclynx.c (NAME(aout,sparclynx_write_object_contents)): Set
        flags from backend info.
        (sparclynx_aout_backend): Initialize exec_hdr_flags field.

Wed May  4 02:56:00 1994  Ken Raeburn  (raeburn@kr-pc.cygnus.com)

        * config.bfd (i386-*-gnu*): Treat like i386-*-mach*.
        (m68*-apollo-*): Treat all Apollo configs the same, don't handle
        BSD specially.

Tue May  3 19:43:21 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * cache.c: Rewrote to work correctly.
        * libbfd.h: Rebuilt.
        * opncls.c (bfd_cache_init, bfd_open_file): Don't declare.
        (bfd_fdopenr): Check return value of bfd_cache_init.

Fri Apr 29 15:08:23 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * cf-m68klynx.c (CALC_ADDEND): Check for PC relative relocs by
        enumerating them, since the reloc type can not serve as an index
        into the m68k COFF howto_table.

Fri Apr 29 09:42:39 1994  Steve Chamberlain  (sac@cygnus.com)

        * config.bfd (*-go32): Changed to coff.
        * coff-h8300.c (JMPL1): Get HOWTO right for 24bit branches.
        * srec.c (srec_write_symbols): Write out the correct number of
        symbols and don't stick in extra nulls.

Tue Apr 26 15:07:24 1994  Stan Shebs  (shebs@andros.cygnus.com)

        * cf-sparclynx.c (LYNXOS, COFF_LONG_FILENAMES): Define.
        * coff-sparc.c (BADMAG): Recognize LYNXCOFFMAGIC.
        (COFF_SPARC): Define.
        * coffcode.h (coff_new_section_hook): If COFF_SPARC, set alignment
        power of data and bss sections to 3.
        * hosts/lynx.h (__LYNXOS): Define.

Tue Apr 26 15:04:26 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * elf32-hppa.c (hppa_elf_reloc): Adjust the addend of relocations
        against section symbols to avoid losing during ld -r.

Tue Apr 26 12:16:41 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elfcode.h (shstrtab_length_fixed): Remove useless static
        variable.
        (struct elf_sect_data): Remove unused structure.
        (elf_object_p): Free memory if error occurs.  Check return value
        of bfd_default_set_arch_mach.  If elf_get_str_section fails,
        preserve error code rather than setting wrong_format.
        (null_shdr): Remove static variable.
        (assign_section_numbers): Remove shstrtab_length_fixed assignment.
        Allocate first section header on BFD obstack rather than using
        null_shdr.
        (bfd_prpsinfo): Remove unused local variable newsect.

Mon Apr 25 15:31:04 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elfcode.h (write_relocs): Undo patch of Apr 10; breaks Solaris.

        * elfcode.h (bfd_section_from_shdr): Use bfd_make_section_anyway
        to create sections.  Check return value of recursive calls.
        (bfd_section_from_phdr): Check return value of bfd_make_section.
        (elf_symbol_from_bfd_symbol): Likewise.
        (elf_object_p): Check return value of bfd_section_from_shdr.
        (section_from_elf_index): Likewise.
        (elf_slurp_symbol_table): Check return value of
        section_from_elf_index.
        (bfd_prstatus): Return boolean value.  Check return value of
        bfd_make_section.
        (bfd_fpregset): Likewise.
        (bfd_prpsinfo): Return boolean value.
        (elf_corefile_note): Check return values of bfd_prstatus,
        bfd_fpregset, and bfd_prpsinfo.
        (elf_core_file_p): Check return value of elf_corefile_note.

Fri Apr 22 11:08:38 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Get rid of the ECOFF .reginfo section hack.
        * ecoff.c (ecoff_mkobject_hook): Don't create a .reginfo section.
        (ecoff_new_section_hook): Don't handle the .reginfo section.
        (ecoff_sizeof_headers): Likewise.
        (ecoff_get_section_contents): Likewise.
        (ecoff_compute_section_file_positions): Likewise.
        (ecoff_compute_reloc_file_positions): Likewise.
        (ecoff_set_section_contents): Likewise.
        (ecoff_write_object_contents): Likewise.
        (ecoff_bfd_final_link): Likewise.
        (ecoff_bfd_copy_private_bfd_data): Copy the GP value and the
        register masks.
        (bfd_ecoff_get_gp_value): New function.
        (bfd_ecoff_set_gp_value): New function.
        (bfd_ecoff_set_regmasks): New function.
        * bfd-in.h (bfd_ecoff_get_gp_value): Declare.
        (bfd_ecoff_set_gp_value): Declare.
        (bfd_ecoff_set_regmasks): Declare.
        * bfd-in2.h: Rebuilt.

        Fix ECOFF objcopy to actually copy debugging information.
        * ecoff.c (ecoff_bfd_copy_private_bfd_data): New function.
        (ecoff_get_extr): Assume that any ECOFF symbol with local clear is
        an external symbol, rather than checking the symbol flags.  Only
        check the flags for non-ECOFF symbols.
        * ecofflink.c (bfd_ecoff_debug_externals): Don't crash if the
        output_section field of the symbol section is NULL.
        * libecoff.h (ecoff_bfd_copy_private_bfd_data): Declare as
        function rather than defining as macro.

        * ieee.c (ieee_object_p): Set bfd_error_got_wrong_format if
        appropriate.

        * targets.c (bfd_target_vector): Add bfd_elf32_powerpc_vec.

        * aout-adobe.c (aout_adobe_set_arch_mach): Check return value of
        bfd_default_set_arch_mach.  Accept bfd_arch_m68k as well as
        bfd_arch_unknown.
        * coffcode.h (coff_set_arch_mach): Check return value of
        bfd_default_set_arch_mach.
        * elfcode.h (elf_set_arch_mach): Don't check a list of ELF
        architectures, just see if the desired architecture matches what
        the ELF backend permits.

        * coffcode.h (coff_set_arch_mach_hook): Rename SHMAGIC to
        SH_ARCH_MAGIC to match change in coff/sh.h.
        (coff_set_flags): Likewise.

        Follow convention in which each NLM header has an 8 byte stamp
        followed by a four byte length.
        * libnlm.h (struct nlm_obj_tdata): Rename nlm_cygnus_section_hdr
        to nlm_cygnus_ext_header, and change type to
        Nlm_Internal_Cygnus_Ext_Header.
        (nlm_cygnus_ext_header): Rename from nlm_cygnus_section_header.
        * nlmcode.h (nlm_swap_auxiliary_headers_in): Use CyGnUsEx instead
        of CyGnUsSeCs.  Rename from cygnus_section to cygnus_ext.  Require
        length word to be 8.
        (nlm_swap_auxiliary_headers_out): Rename from cygnus_section to
        cygnus_ext.  Set length word to 8.
        (nlm_compute_section_file_positions): Rename from cygnus_section
        to cygnus_ext.

Thu Apr 21 22:54:22 1994  Stu Grossman  (grossman at cygnus.com)

        * nlmcode.h (nlm_swap_auxiliary_headers_in):  Keep section table
        (from CyGnUsSeCs) in more permanent memory to keep section names
        from getting trashed.

Thu Apr 21 09:29:37 1994  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        * libelf.h (elf_obj_tdata):  Add members for dynamic symbol table
        handling.
        * elfcode.h (bfd_section_from_shdr):  Handle dynamic symbol table.
        * elfcode.h (elf_slurp_symbol_table):  Take additional parameter
        to select static or dynamic symbol table and return number of
        symbols slurped or -1 on error.
        * elfcode.h (elf_get_symtab):  Set bfd symcount from
        elf_slurp_symbol_table result.
        * elfcode.h (elf_get_dynamic_symtab_upper_bound,
        elf_canonicalize_dynamic_symtab):  New functions to handle dynamic
        symbol table.
        * elf32-target.h, elf64-target.h (BFD_JUMP_TABLE_DYNAMIC):
        Change to handle dynamic symbol table, provide default definitions
        for dynamic relocs.
        * aoutx.h (howto_table_std, NAME(aout,swap_std_reloc_out),
        NAME(aout,swap_std_reloc_in), aout_link_input_section_std,
        aout_link_reloc_link_order):  Handle r_jmptable and r_relative
        relocations.

Thu Apr 21 11:58:19 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Clean up uses of _bfd_dummy_target (from Peter Schauer).
        * libbfd.c (_bfd_dummy_target): Set bfd_error_wrong_format.
        * nlm-target.h (nlm_core_file_p): Define as _bfd_dummy_target, not
        NULL.
        * srec.c (srec_vec): Use _bfd_dummy_target, not NULL, in
        _bfd_check_format.
        (symbolsrec_vec): Likewise.
        * tekhex.c (tekhex_vec): Likewise.

        * libnlm.h (struct nlm_obj_tdata): Add nlm_cygnus_section_hdr
        field.
        (nlm_cygnus_section_header): New accessor macro.
        * nlmcode.h (nlm_object_p): Free new tdata structure if failure.
        Add fixed sections before swapping in auxiliary headers.  After
        adding sections, treat errors as real, not as wrong format.
        (nlm_swap_auxiliary_headers_in): Swap in the sections header; add
        sections to the BFD for each section it describes.
        (nlm_swap_auxiliary_headers_out): Swap out the sections header.
        (nlm_compute_section_file_positions): Account for the size of the
        sections header.

Wed Apr 20 16:45:51 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        * coff-sparc.c (sparccoff_vec): Change minimum alignment power to
        2, so that stab sections can be multiples of 4 bytes only.

        * hosts/i386aix.h: Changes to avoid prototypes conflicts with the
        ones defined in stdlib.h.  (From Minh Tran-Le.)

Wed Apr 20 14:15:21 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * nlm32-ppc.c: Complete rewrite for new version of PowerPC
        NetWare.  Old code still present, but ifdeffed out.

        * nlmcode.h (nlm_swap_auxiliary_headers_in): Don't assume a
        particular format for the customer header.  Allocate a block of
        memory and read it into that.
        (nlm_swap_auxiliary_headers_out): Write out the block of memory.
        (nlm_compute_section_file_positions): Include length of customer
        header when computing its size.

Mon Apr 18 14:27:17 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_prep_headers): Get the space's number from the
        backend private section data rather than target_index.
        (bfd_som_set_section_attributes): Store the space's number
        in the backend private section data rather than target_index.

        * som.h (som_copyable_section_data_struct): Add space_number.

Fri Apr 15 12:22:07 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * coff-a29k.c (reloc_processing): Always set the address of a
        R_IHCONST reloc to that of the immediately preceding R_IHIHALF.
        gas does this anyhow, but some other assemblers seem to leave
        garbage in the R_IHCONST address field.

        * bfd/archive.c: Consistently use ARFMAG; from
        schwab@issan.informatik.uni-dortmund.de (Andreas Schwab).
        (_bfd_write_archive_contents): Use ARFMAG rather than '`' and
        '\012'.
        (bsd_write_armap): Likewise.
        (coff_write_armap): Likewise.

        * coff-mips.c (mips_relocate_section): When relaxing, adjust local
        relocs against the .text section as required.
        * ecofflink.c (bfd_ecoff_debug_accumulate): When relaxing, adjust
        PDR addresses as required.

        * ecoff.c (ecoff_emit_aggregate): Take fdr argument.  Map fdr
        index through rfd map if it exists.  Check for a couple of cases
        which gdb handles specially.  Change all callers.
        (ecoff_type_to_string): Take fdr argument rather than aux_ptr and
        bigendian argument.  Change all callers.
        (ecoff_print_symbol): Handle stStruct, stUnion and stEnum.

Thu Apr 14 13:05:10 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * coff-mips.c (mips_howto_table): Add dummy entries to account for
        numbering changes in include/coff/mips.h.  Add entries for
        MIPS_R_RELHI and MIPS_R_RELLO.
        (mips_ecoff_swap_reloc_in): Handle an extra bit for the reloc type
        when little endian.  Treat internal MIPS_R_RELLO or MIPS_R_RELHI
        relocs like MIPS_R_SWITCH, and convert r_offset from 24 to 32
        bits.
        (mips_ecoff_swap_reloc_out): Likewise.
        (mips_adjust_reloc_in): Handle internal MIPS_R_RELLO or
        MIPS_R_RELHI relocs like MIPS_R_SWITCH.
        (mips_adjust_reloc_out): Likewise.
        (mips_relhi_addr, mips_relhi_addend): New static variables.
        (mips_relhi_reloc, mips_rello_reloc): New functions.
        (mips_bfd_reloc_type_lookup): Turn BFD_RELOC_PCREL_HI16_S into
        MIPS_R_RELHI and turn BFD_RELOC_PCREL_LO16 into MIPS_R_RELLO.
        (mips_relocate_hi): Rename from mips_relocate_refhi, and add pcrel
        argument.  Changed all callers.
        (mips_relocate_section): Rename got_reflo to got_lo and
        reflo_int_rel to lo_int_rel.  Handle MIPS_R_RELLO and MIPS_R_RELHI
        relocs.
        (mips_relax_section): Adjust MIPS_R_RELHI/MIPS_R_RELLO pairs when
        expanding a PC relative call.

        * reloc.c (bfd_reloc_code_real_type): Add BFD_RELOC_PCREL_HI16_S
        and BFD_RELOC_PCREL_LO16.
        * bfd-in2.h: Rebuilt.

Wed Apr 13 11:50:07 1994  Stan Shebs  (shebs@andros.cygnus.com)

        * coff-sparc.c (sparccoff_vec): Set minimum alignment power to 3.

Tue Apr 12 13:36:20 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_write_fixups): Always emit at least
        one relocation for any non-bss section.

Mon Apr 11 14:41:44 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elfcode.h (assign_file_positions_except_relocs): Don't require
        the file alignment to correspond to the page size when linking
        with -N.

Sun Apr 10 01:02:24 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * elfcode.h (write_relocs): For rela relocations, adjust the
        addend for relocations involving section symbols to account
        for the lossage of 1:1 mapping from input section symbols to
        output section symbols.

Fri Apr  8 12:22:02 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aoutx.h (NAME(aout,make_sections)): New function.
        (NAME(aout,some_aout_object_p)): Call NAME(aout,make_sections)
        rather than making sections inline.
        (NAME(aout,mkobject)): Don't make any sections.
        (NAME(aout,adjust_sizes_and_vmas)): Call NAME(aout,make_sections).
        (NAME(aout,final_link)): Don't dereference obj_textsec (abfd) or
        obj_datasec (abfd) if they are NULL.
        * libaout.h (NAME(aout,make_sections)): Declare.
        * bout.c (b_out_mkobject): Don't make any sections.
        (b_out_write_object_contents): Call aout_32_make_sections.
        (b_out_set_section_contents): Likewise.
        * i386os9k.c (os9k_mkobject): Don't make any sections.
        (os9k_write_object_contents): Call aout_32_make_sections.
        (os9k_set_section_contents): Likewise.

        * aoutx.h (NAME(aout,new_section_hook)): Don't set N_EXT in target
        index.

Wed Apr  6 20:44:56 1994  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        * config.bfd, configure.host:  Add mips-*-sysv4* support.

Thu Apr  7 14:23:05 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * coff-mips.c (mips_howto_table): Add entry for MIPS_R_SWITCH.
        (mips_ecoff_swap_reloc_in): For MIPS_R_SWTICH, copy r_symndx into
        r_offset and set r_symndx to RELOC_SECTION_TEXT.
        (mips_ecoff_swap_reloc_out): For MIPS_R_SWITCH, get the r_symndx
        value from the r_offset field.
        (mips_adjust_reloc_in): Maximum r_type value is now MIPS_R_SWITCH.
        For MIPS_R_SWITCH, copy the r_offset field into the addend field.
        (mips_adjust_reloc_out): For MIPS_R_SWITCH, copy the addend field
        into the r_offset field.
        (mips_switch_reloc): New function.
        (mips_bfd_reloc_type_lookup): Translate BFD_RELOC_GPREL32 into
        MIPS_R_SWITCH.
        (mips_relocate_section): Handle MIPS_R_SWITCH.
        (mips_relax_section): Adjust MIPS_R_SWITCH offset if necessary.

Thu Apr  7 11:10:51 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * elfcode.h (elf_set_section_contents): Support calling the backend
        function elf_backend_begin_write_processing when just beginning to
        write an object file.

        * libelf.h (elf_backend_begin_write_processing): Declare.

        * elf{32,64}-target.h (elf_backend_begin_write_processing): Provide
        a default definition.
        (elf{32,64}_bed): Add elf_backend_begin_write_processing.
        
        * elf32-hppa.h (elf_hppa_tc_symbol): Delete extern declaration.
        (elf_hppa_tc_make_sections): Likewise.

        * elf32-hppa.c (symext_chain_built): Delete.
        (symext_chain_size): Renamed from symextn_contents_real_size.
        (elf32_hppa_backend_{begin,final}_write_processing): New functions.
        (add_entry_to_symext_chain): New function.
        (hppa_elf_set_section_contents): Ignore writes to the symbol extension
        section until it's been rebuilt internally.
        (hppa_elf_get_section_contents): Symbol extension section is no
        longer special.
        (elf_backend_{begin,final}_write_processing): Define.
        (elf_hppa_tc_make_sections): Simplify now that much code has
        migrated into elf32_hppa_backend_{being,final}_write_processing.

Wed Apr  6 17:24:14 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Add new target vectors to read the dynamic symbols and dynamic
        relocs.  Change a.out to use these rather than reading the dynamic
        symbols and relocs along with the normal symbols and relocs.
        * targets.c (bfd_target): Add fields
        _bfd_get_dynamic_symtab_upper_bound,
        _bfd_canonicalize_dynamic_symtab,
        _bfd_get_dynamic_reloc_upper_bound,
        _bfd_canonicalize_dynamic_reloc.
        (BFD_JUMP_TABLE_DYNAMIC): Define.
        * libbfd-in.h (_bfd_nodynamic_get_dynamic_symtab_upper_bound):
        Define.
        (_bfd_nodynamic_canonicalize_dynamic_symtab): Define.
        (_bfd_nodynamic_get_dynamic_reloc_upper_bound): Define.
        (_bfd_nodynamic_canonicalize_dynamic_reloc): Define.
        * bfd.c (bfd_get_dynamic_symtab_upper_bound): Define.
        (bfd_canonicalize_dynamic_symtab): Define.
        (bfd_get_dynamic_reloc_upper_bound): Define.
        (bfd_canonicalize_dynamic_reloc): Define.
        * sunos.c (MY_read_dynamic_symbols): Don't define.
        (MY_read_dynamic_relocs): Don't define.
        (MY_get_dynamic_symtab_upper_bound): Define.
        (MY_canonicalize_dynamic_symtab): Define.
        (MY_get_dynamic_reloc_upper_bound): Define.
        (MY_canonicalize_dynamic_reloc): Define.
        (struct sunos_dynamic_info): Change type of dynsym_count and
        dynrel_count to long.  Add fields canonical_dynsym and
        canonical_dynrel.
        (sunos_read_dynamic_info): Check that BFD had DYNAMIC flag set.
        Clear info->canonical_dynsym and info->canonical_dynrel.
        (MY(read_dynamic_symbols)): Removed.
        (MY(read_dynamic_relocs)): Removed.
        (sunos_get_dynamic_symtab_upper_bound): New function.
        (sunos_canonicalize_dynamic_symtab): New function.
        (sunos_get_dynamic_reloc_upper_bound): New function.
        (sunos_canonicalize_dynamic_reloc): New function.
        * libaout.h: Declare struct reloc_ext_external and
        reloc_std_external to avoid prototype problems.
        (struct aout_backend_data): Remove fields read_dynamic_symbols and
        read_dynamic_relocs.
        (NAME(aout,translate_symbol_table)): Declare.
        (NAME(aout,swap_ext_reloc_in)): Declare.
        (NAME(aout,swap_std_reloc_in)): Declare.
        * aoutx.h (NAME(aout,translate_symbol_table)): Renamed from
        translate_symbol_table and made non-static.  Changed all callers.
        (NAME(aout,slurp_symbol_table)): Don't read dynamic symbols.
        (NAME(aout,slurp_reloc_table)): Don't read dynamic relocs.
        (NAME(aout,get_reloc_upper_bound)): Don't count dynamic relocs.
        * aoutf1.h (aout_32_sunos4_write_object_contents): Don't bother to
        remove dynamic symbols and relocs.  They will no longer be
        present.
        (MY_read_dynamic_symbols): Don't define.
        (MY_read_dynamic_relocs): Don't define.
        (sunos4_aout_backend): Don't initialize dynamic entry points.
        * aout-target.h (MY_read_dynamic_symbols): Don't define.
        (MY_read_dynamic_relocs): Don't define.
        (MY(backend_data)): Don't initialize dynamic entry points.
        (MY_get_dynamic_symtab_upper_bound): If not defined, define to
        _bfd_nodynamic version.
        (MY_canonicalize_dynamic_symtab): Likewise.
        (MY_get_dynamic_reloc_upper_bound): Likewise.
        (MY_canonicalize_dynamic_reloc): Likewise.
        * All backends: Added BFD_JUMP_TABLE_DYNAMIC to target vector.
        * bfd-in2.h: Rebuilt.
        * libbfd.h: Rebuilt.

        * cf-m68klynx.c: Include sysdep.h.

        * hp300hpux.c: Removed some spaces in uses of NAME to avoid
        problems with traditional C compilers.

        * targets.c (bfd_target): Rearranged fields in target vector.
        Removed _bfd_debug_info_start, _bfd_debug_info_end and
        _bfd_debug_info_accumulate, which were never used.
        (BFD_JUMP_TABLE_GENERIC, BFD_JUMP_TABLE_COPY): Defined.
        (BFD_JUMP_TABLE_CORE, BFD_JUMP_TABLE_ARCHIVE): Defined.
        (BFD_JUMP_TABLE_SYMBOLS, BFD_JUMP_TABLE_RELOCS): Defined.
        (BFD_JUMP_TABLE_WRITE, BFD_JUMP_TABLE_LINK): Defined.
        * All backends: Changed to use the new BFD_JUMP_TABLE_* macros
        rather than the single JUMP_TABLE macro.  Removed many of the
        weird macro definitions needed to support the monolithic
        JUMP_TABLE.
        * bfd-in.h (JUMP_TABLE): Removed.
        * libbfd-in.h: Define a bunch of macros, and declare a few
        functions, for use with the new BFD_JUMP_TABLE_* macros.
        * libbfd.c (_bfd_dummy_new_section_hook): Removed.
        (bfd_false): Set bfd_error_invalid_operation.
        (bfd_nullvoidptr): Likewise.
        (bfd_n1): New function.
        (_bfd_nocore_core_file_matches_executable_p): Renamed from
        _bfd_dummy_core_file_matches_executable_p.
        (_bfd_nocore_core_file_failing_command): Similar rename.  Set
        bfd_error_invalid_operation.
        (_bfd_nocore_core_file_failing_signal): Likewise.
        (_bfd_generic_get_section_contents): Renamed from
        bfd_generic_get_section_contents.  Changed all callers.
        (_bfd_generic_set_section_contents): Similar rename.
        * ieee.c: #if 0 out ieee_bfd_debug_info_start,
        ieee_bfd_debug_info_end, ieee_bfd_debug_info_accumulate.  They
        were never called.
        * bfd-in2.h: Rebuilt.
        * libbfd.h: Rebuilt.

Tue Apr  5 22:10:04 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * Crude support for examining dynamic libraries.
        * som.c (som_object_setup): Set DYNAMIC flag for SHL_MAGIC and
        DL_MAGIC objects.
        (som_prep_headers): Preserve the system_id for DYNAMIC objects.
        Use SHL_MAGIC as the magic number of the DYNAMIC flag is set.
        Write exec headers for DYNAMIC objects.
        (som_begin_writing): DYNAMIC objects have the same alignment
        restrictions as D_PAGED objects.
        (bfd_section_from_som_symbol): Treat DYNAMIC objects like EXEC_P
        objects.
        (object_flags): Add DYNAMIC.

Tue Apr  5 17:48:52 1994  Stan Shebs  (shebs@andros.cygnus.com)

        * i386lynx.c, sparclynx.c (NAME): Remove embedded whitespace in
        macro uses, confuses some non-ANSI compilers.

Tue Apr  5 15:50:01 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_bfd_free_cached_info): Add missing PARAMS decl.
        Don't free anything if we don't have a bfd_object.
        (som_close_and_cleanup): Call som_bfd_free_cached_info.

Tue Apr  5 11:22:38 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elf32-mips.c (mips_elf_final_link): Don't remove empty sections.
        It turns out not to be required on Irix 5, and it causes problems
        if the sections happen to contain symbols.

        * elfcode.h (write_shdrs_and_ehdr): Correct bfd_write check.

        * aoutx.h (NAME(aout,canonicalize_reloc)): Don't error out if
        section->relocation is NULL; malloc might have returned NULL when
        given a zero size if there were no relocations.
        * bout.c (b_out_canonicalize_reloc): Likewise.
        * coffcode.h (coff_canonicalize_reloc): Likewise.
        * ecoff.c (ecoff_canonicalize_reloc): Likewise.
        * elfcode.h (elf_canonicalize_reloc): Likewise.
        * mipsbsd.c (MY(canonicalize_reloc)): Likewise.
        * i386lynx.c (NAME(lynx,canonicalize_reloc)): Likewise.
        * nlmcode.h (nlm_canonicalize_reloc): Likewise.
        * som.c (som_canonicalize_reloc): Likewise.
        * hp300hpux.c (MY(slurp_reloc_table)): Likewise.  Also, if malloc
        returns NULL, don't report an error if we asked for zero bytes.
        * i386lynx.c (NAME(lynx,slurp_reloc_table)): If malloc returns
        NULL, don't report an error if we asked for zero bytes.
        * nlmcode.h (nlm_slurp_reloc_fixups): Likewise.

Mon Apr  4 15:30:49 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aoutx.h (NAME(aout,bfd_free_cached_info)): Don't free anything
        if we don't have a bfd_object.

        Made sure that every call to bfd_read, bfd_write, and bfd_seek
        checks the return value and handled bfd_error correctly.  These
        changes are not itemised.  Also:
        * aoutx.h (emit_strtab): Change return type to boolean, and return
        errors.
        (NAME(aout,write_syms)): Check emit_strtab return value.
        (NAME(aout,final_link)): Likewise.
        * coffcode.h (coff_write_relocs): Change return type to boolean,
        and return errors.
        (coff_write_object_contents): Check coff_write_relocs return
        value.
        * i386os9k.c (os9k_swap_exec_header_in): Change return type to
        boolean.
        (os9k_object_p): Check os9k_swap_exec_header_in return value.
        * oasys.c (oasys_read_record): Change return type to boolean.
        (oasys_slurp_symbol_table: Check oasys_read_record return value.
        (oasys_object_p, oasys_slurp_section_data): Likewise.
        (oasys_write_record): Change return type to boolean.
        (oasys_write_syms): Likewise.  Also, check oasys_write_record
        return value.
        (oasys_write_sections): Check oasys_write_record return value.
        (oasys_write_header): Change return type to boolean.  Check
        oasys_write_record return value.
        (oasys_write_end, oasys_write_data): Likewise.
        (oasys_write_object_contents): Check return values of
        oasys_write_header, oasys_write_syms, oasys_write_data, and
        oasys_write_end.
        * srec.c (srec_write_record): Change return type to boolean.
        (srec_write_header): Likewise.  Also, check srec_write_record
        return value.
        (srec_write_section, srec_write_terminator): Likewise.
        (srec_write_symbols): Change return type to boolean.
        (internal_srec_write_object_contents): Check return value of
        srec_write_symbols, srec_write_header, srec_write_section, and
        srec_write_terminator.

        * Makefile.in: Rebuilt dependencies.

Mon Apr  4 10:56:45 1994  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        * aix386-core.c (aix386_bfd_is_local_label):  Correct cast from
        asection to asymbol.
        * ptrace-core.c (ptrace_unix_bfd_is_local_label):  Correct cast from
        bfd to asymbol.
        * trad-core.c (trad_unix_bfd_is_local_label):  Correct cast from
        asection to asymbol.

Sun Apr  3 18:27:29 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_slurp_string_table): Use malloc to allocate space
        for the cached copy of the native string table.
        (som_slurp_symbol_table): Likewise for the native symbol table.
        (som_slurp_reloc_table): Likewise for the native and generic
        relocation tables.
        (som_bfd_free_cached_info): Free the cached native strings,
        symbols, and relocations.  Also free the canonical cached
        relocations.

Fri Apr  1 12:40:58 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aoutx.h (aout_link_write_symbols): If keep_memory is false, make
        sure the symbol name is stored in permanent memory before adding
        it to the string table.

        * archive.c (_bfd_write_archive_contents): Once we've found an
        object, don't bother to look for more when deciding whether to
        build a map.
        (compute_and_write_armap): After adding the symbols for a BFD,
        call bfd_free_cached_info on it.

        Add bfd_free_cached_info support to a.out backends.
        * aoutx.h (aout_get_external_symbols): Renamed from
        aout_link_get_symbols.  Read strings even if symbols have been
        read.  Store string size in obj_aout_string_size.
        (NAME(aout,slurp_symbol_table)): Call aout_get_external_symbols to
        read the symbols.  Allocate the cached symbols with malloc, not
        bfd_alloc.
        (NAME(aout,slurp_reloc_table)): Allocate the cached relocs with
        malloc, not bfd_alloc.
        (NAME(aout,bfd_free_cached_info)): New function; free cached
        symbols and relocs.
        * libaout.h (struct aoutdata): Add external_string_size field.
        (obj_aout_external_string_size): New accessor macro.
        (NAME(aout,close_and_cleanup)): Don't declare.
        (NAME(aout,bfd_free_cached_info)): Declare.
        (aout_32_close_and_cleanup): Don't define.
        (aout_64_close_and_cleanup): Don't define.
        * aout-target.h (MY_bfd_free_cached_info): If not already defined,
        define as NAME(aout,free_cached_info).
        (MY_close_and_cleanup): If not already defined, define as
        MY_bfd_free_cached_info.
        * aout-adobe.c (aout_32_close_and_cleanup): Define.
        (aout_32_bfd_free_cached_info): Don't define.
        * bout.c (aout_32_close_and_cleanup): Define.
        (aout_32_bfd_free_cached_info): Don't define.
        * hp300hpux.c (MY_bfd_free_cached_info): Define as bfd_true.
        (MY_close_and_cleanup): Don't define.
        * i386lynx.c (NAME(lynx,slurp_reloc_table)): Allocate the cached
        relocs with malloc, not bfd_alloc.
        * i386os9k.c (aout_32_close_and_cleanup): Define.
        (aout_32_bfd_free_cached_info): Don't define.

        Add a new entry point to free memory cached by a BFD.
        * targets.c (bfd_target): Add _bfd_free_cached_info field.
        * bfd.c (bfd_free_cached_info): Define.
        * bfd-in.h (JUMP_TABLE): Add _bfd_free_cached_info.
        * bfd-in2.h: Rebuilt.
        * All backends: Initialize bfd_free_cached_info entry point to
        bfd_true.

        * elf32-hppa.c (elf_hppa_reloc_type_lookup): Correct type of
        first, unused, argument.
        (hppa_elf_is_local_label): Declare instead of
        som_bfd_is_local_label.

        * coff-a29k.c (a29k_reloc): Add reloc_entry->address to value of
        absolute R_IREL reloc.

Thu Mar 31 11:52:15 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Added some support for Irix 4 shared libraries.
        * ecoff.c (ecoff_new_section_hook): Set SEC_SHARED_LIBRARY for a
        .lib section.
        (ecoff_sec_to_styp_flags): Set SEC_SHARED_LIBRARY if
        STYP_ECOFF_LIB bit is set.
        (ecoff_compute_section_file_positions): Round the contents of a
        .lib section up to the next page boundary.
        (ecoff_set_section_contents): If we see a .lib section, increment
        the vma by one to count the number of shared libraries we have.
        (ecoff_write_object_contents): Don't crash if we see a
        STYP_ECOFF_LIB section, and don't adjust text_start or data_start
        or bss_size either.

        * coffcode.h (CALC_ADDEND): Change to fetch original symbol value
        from original BFD, rather than using value of current BFD symbol.
        Needed for new linker.
        * coff-sparc.c (CALC_ADDEND): Likewise.

        * ecoff.c (ecoff_write_object_contents): Set the text_start and
        data_start entries in the optional header correctly even if a text
        or data section starts at location zero.

        * reloc.c (bfd_reloc_code_real_type): Added BFD_RELOC_26 (from sef
        and raeburn).
        * bfd-in2.h: Rebuilt.

        * nlm32-i386.c (nlm_i386_read_import): Null terminate the symbol
        name.
        * nlm32-alpha.c (nlm_alpha_read_import): Likewise.
        * nlm32-sparc.c (nlm_sparc_read_import): Likewise.

        * coffgen.c (coff_write_symbol): Reindented.  Changed to return
        boolean, and changed written to unsigned int *.  Check error
        returns from called functions.
        (coff_write_alien_symbol): Likewise.
        (coff_write_native_symbol): Likewise.
        (coff_write_symbols): Likewise.  Reworked checks on whether to
        write symbol name to string table for clarity and to avoid core
        dumping when given a non COFF symbol.
        * libcoff-in.h (coff_write_symbols): Declare as returning boolean.
        * libcoff.h: Rebuilt.
        * coffcode.h (coff_write_object_contents): Check return value of
        coff_write_symbols.

Wed Mar 30 16:25:41 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Changes to let BFD return an error indication from
        get_symtab_upper_bound, bfd_canonicalize_symtab,
        bfd_get_reloc_upper_bound, and bfd_canonicalize_reloc.  They now
        return long instead of unsigned int, and use -1 to indicate an
        error.  Along the way, rename get_symtab_upper_bound to
        bfd_get_symtab_upper_bound.
        * bfd.c (bfd_get_reloc_upper_bound): Return long, and -1 on
        errors.
        (bfd_canonicalize_reloc): Likewise.
        * syms.c (bfd_get_symtab_upper_bound): Renamed from
        get_symtab_upper_bound.
        * targets.c (bfd_target): Renamed _get_symtab_upper_bound to
        _bfd_get_symtab_upper_bound, and changed it and
        _bfd_canonicalize_symtab and _get_reloc_upper_bound and
        _bfd_canonicalize_reloc to all return long.
        * aoutx.h (NAME(aout,get_symtab)): Return long, and -1 on errors.
        (NAME(aout,canonicalize_reloc)): Likewise.
        (NAME(aout,get_reloc_upper_bound)): Likewise.
        (NAME(aout,get_symtab_upper_bound)): Likewise.
        * bout.c (b_out_canonicalize_reloc): Likewise.
        (b_out_get_reloc_upper_bound): Likewise.
        * coffcode.h (coff_canonicalize_reloc): Likewise.
        * coffgen.c (coff_get_symtab_upper_bound): Likewise.
        (coff_get_symtab): Likewise.
        (coff_get_reloc_upper_bound): Likewise.
        * ecoff.c (ecoff_get_symtab_upper_bound): Likewise.
        (ecoff_get_symtab): Likewise.
        (ecoff_canonicalize_reloc): Likewise.
        * elfcode.h (elf_get_symtab_upper_bound): Likewise.
        (elf_get_reloc_upper_bound): Likewise.
        (elf_canonicalize_reloc): Likewise.
        (elf_get_symtab): Likewise.
        * hp300hpux.c (MY(get_symtab)): Likewise.
        (MY(get_symtab_upper_bound)): Likewise.
        (MY(canonicalize_reloc)): Likewise.
        * i386lynx.c (NAME(lynx,canonicalize_reloc)): Likewise.
        * ieee.c (ieee_slurp_external_symbols): Change return type to
        boolean.  Check for errors from get_symbol.
        (ieee_slurp_symbol_table): Change return type to boolean.  Check
        for errors from ieee_slurp_external_symbols.
        (ieee_get_symtab_upper_bound): Return long, and -1 on errors.
        (ieee_get_symtab): Likewise.
        (ieee_get_reloc_upper_bound): Likewise.
        (ieee_canonicalize_reloc): Likewise.
        * mipsbsd.c (MY(canonicalize_reloc)): Likewise.
        * nlmcode.h (nlm_get_symtab_upper_bound): Likewise.
        (nlm_get_symtab): Likewise.
        (nlm_get_reloc_upper_bound): Likewise.
        (nlm_canonicalize_reloc): Likewise.
        * oasys.c (oasys_get_symtab_upper_bound): Likewise.
        (oasys_get_symtab): Likewise.
        (oasys_get_reloc_upper_bound): Likewise.
        (oasys_canonicalize_reloc): Likewise.
        * som.c (som_get_symtab_upper_bound): Likewise.
        (som_get_symtab): Likewise.
        (som_get_reloc_upper_bound): Likewise.
        (som_canonicalize_reloc): Likewise.
        * srec.c (srec_get_symtab_upper_bound): Likewise.
        (srec_get_symtab): Likewise.
        (srec_get_reloc_upper_bound): Define as bfd_0l.
        (srec_canonicalize_reloc): Likewise.
        * tekhex.c (tekhex_get_symtab): Return long, and -1 on errors.
        (tekhex_get_symtab_upper_bound): Likewise.
        (tekhex_get_reloc_upper_bound): Define as bfd_0l.
        (tekhex_canonicalize_reloc): Likewise.
        * libaout.h (NAME(aout,get_symtab_upper_bound)): Change
        declaration to return long.
        (NAME(aout,get_symtab)): Likewise.
        (NAME(aout,canonicalize_reloc)): Likewise.
        (NAME(aout,get_reloc_upper_bound)): Likewise.
        * libcoff-in.h (coff_get_symtab_upper_bound): Likewise.
        (coff_get_symtab): Likewise.
        (coff_get_reloc_upper_bound): Likewise.
        * libecoff.h (ecoff_get_symtab_upper_bound): Likewise.
        (ecoff_get_symtab): Likewise.
        (ecoff_canonicalize_reloc): Likewise.
        * libelf.h (bfd_elf32_get_symtab_upper_bound): Likewise.
        (bfd_elf32_get_symtab): Likewise.
        (bfd_elf32_get_reloc_upper_bound): Likewise.
        (bfd_elf32_canonicalize_reloc): Likewise.
        (bfd_elf64_get_symtab_upper_bound): Likewise.
        (bfd_elf64_get_symtab): Likewise.
        (bfd_elf64_get_reloc_upper_bound): Likewise.
        (bfd_elf64_canonicalize_reloc): Likewise.
        * libnlm.h (nlmNAME(get_symtab_upper_bound)): Likewise.
        (nlmNAME(get_symtab)): Likewise.
        (nlmNAME(get_reloc_upper_bound)): Likewise.
        (nlmNAME(canonicalize_reloc)): Likewise.
        * archive.c (compute_and_write_armap): Use error_return and
        no_memory_return labels rather than freeing information in various
        places.  Change storage, symcount and src_count to long.  Check
        errors from bfd_get_symtab_upper_bound and
        bfd_canonicalize_symtab.
        * bout.c (b_out_relax_section): Change reloc_size to long.  Check
        for errors from bfd_get_reloc_upper_bound and
        bfd_canonicalize_reloc.
        (b_out_get_relocated_section_contents): Likewise.
        * coff-alpha.c (alpha_ecoff_get_relocated_section_contents):
        Likewise.
        * elf32-mips.c: Likewise.
        * elf32-hppa.c (hppa_elf_stub_finish): Likewise.
        (hppa_look_for_stubs_in_section): Check for errors from
        bfd_get_symtab_upper_bound, bfd_canonicalize_symtab, and
        bfd_canonicalize_reloc.
        * ecofflink.c (bfd_ecoff_debug_accumulate_other): Check for errors
        from bfd_get_symtab_upper_bound and bfd_canonicalize_symtab.
        * linker.c (generic_link_read_symbols): Likewise.
        (_bfd_generic_final_link): Check for errors from
        bfd_get_reloc_upper_bound and bfd_canonicalize_reloc.
        * reloc.c (bfd_generic_get_relocated_section_contents): Likewise.
        * reloc16.c (bfd_coff_reloc16_relax_section): Likewise.
        (bfd_coff_reloc16_get_relocated_section_contents): Likewise.
        * libbfd.c (bfd_0l): New function.
        * libbfd-in.h (bfd_0l): Declare.
        * aix386-core.c: Change get_symtab_upper_bound, get_symtab,
        get_reloc_upper_bound, and canonicalize_reloc to use bfd_0l rather
        than bfd_0u.
        * cisco-core.c, hppabsd-core.c, hpux-core.c: Likewise.
        * irix-core.c, osf-core.c, ptrace-core.c, trad-core.c: Likewise.
        * bfd-in2.h: Rebuilt.
        * libbfd.h: Rebuilt.
        * libcoff.h: Rebuilt.

        * nlm32-sparc.c (nlm_sparc_read_reloc): Remove unused variables
        temp and name.

Wed Mar 30 08:33:04 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * hosts/dpx2.h: Define POSIX_UTIME.

Wed Mar 30 00:31:49 1994  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        * i386dynix.c, config/i386-dynix.mt:  New files, handling Dynix
        variant of a.out.
        * configure.in, config.bfd:  Use them for Dynix.
        * Makefile.in:  Add dependencies for i386dynix.o. 
        * targets.c:  Add definition for i386dynix_vec.
        * hosts/symmetry.h:  Do not define TRAD_CORE_USER_OFFSET for Dynix.
        Define HOST_DATA_START_ADDR and TRAD_UNIX_CORE_FILE_FAILING_SIGNAL
        for Dynix. Remove inclusion of dynix3.h, Dynix bfd is now handled by
        i386dynix.c

Mon Mar 28 12:53:27 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * Makefile.in (BFD32_BACKENDS): Add coff-sparc.o.

        * coffcode.h (coff_set_flags): Handle bfd_arch_powerpc like
        bfd_arch_rs6000.

        * config.bfd (powerpc-*-aix*): New target; use rs6000.mt.
        * config/rs6000.mt (SELECT_ARCHITECTURES): Add bfd_powerpc_arch.

        * aoutx.h (translate_from_native_sym_flags): Set SEC_RELOC flag
        for generated constructor section.

Sun Mar 27 16:25:22 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_begin_writing): New approach at dealing with holes
        in executables left by the HP linker.  Does not rely on subspace
        alignments as subspaces are *NOT* guaranteed to be properly
        aligned in an executable (can you believe that!).

Sat Mar 26 10:25:43 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_get_section_contents): New function.  Do not try
        to actually read data from a section that doesn't have either
        SEC_LOAD or SEC_DEBUGGING set (eg $BSS$) just return true.

        * libbfd.c (bfd_read): Set bfd_error as appropriate for a short
        read. (bfd_error_system_call or bfd_error_file_truncated).

        * som.c: Do not blindly set bfd_error_system_call after a
        failing bfd_read, bfd_write, or bfd_seek.  In a few places
        (like som_object_p) override the error status set by bfd_read.

        * aix386-core.c, aout-encap,c archive.c, bout.c: Likewise.
        * coff-rs6000.c, coffgen.c ecoff.c, elf.c: Likewise.
        * elf32-hppa.c, elfcode.h, hp300hpux.c, i386lynx.c: Likewise.
        * nlm32-alpha.c, nlm32-i386.c, nlm32-sparc.c: Likewise.

        * som.c: Check return values from several bfd_{seek,read,write}
        calls that we just assumed were not failing.

Fri Mar 25 11:44:06 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * hosts/sysv4.h (HAVE_PROCFS): Add comments about ptx4.
        * config/sysv4.mh: Add comment.
        * config/symmetry.mh: Change comment.
        * configure.host: Use sysv4, not symmetry, for i[34]86-sequent-sysv4*.

Fri Mar 25 17:10:45 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Changes to support linker relaxing of embedded MIPS PIC code to
        use a five instruction sequence for function calls which are out of
        range of the bal instruction.
        * libecoff.h (struct ecoff_section_tdata): Define.
        (ecoff_section_data): Define.
        (ecoff_bfd_relax_section): Don't define.
        * ecoff.c (ecoff_final_link_debug_accumulate): Don't read or free
        the debugging information if it has already been read.
        (ecoff_indirect_link_order): Handle _cooked_size being different
        from _raw_size.  Don't reread the contents or the relocs if they
        have already been read in.
        * coff-mips.c (mips_howto_table): Change bitsize of PCREL16 from
        18 to 16.
        (PCREL16_EXPANSION_ADJUSTMENT): Define.
        (mips_relocate_refhi): Take adjust argument.
        (mips_relocate_section): Handle reloc offsets stored in section
        used_by_bfd field.  Call mips_relax_pcrel16 to handle details of
        expanding an out of range PCREL16.  Keep trace of adjustments
        required by expansions.  Set s and unset h when converting a reloc
        from undefined to section.  Change handling of PC relative relocs:
        if against a section, they are correct in the object file, if
        against an external symbol they are pcrel_offset.
        (mips_relax_section): New function.
        (mips_relax_pcrel16): New function.
        (ecoff_bfd_relax_section): Define.
        * coff-alpha.c (ecoff_bfd_relax_section): Define.
        * ecofflink.c (bfd_ecoff_debug_accumulate): Handle adjustments
        built by mips_relax_section when writing out addresses.
        * elf32-mips.c (mips_elf_read_ecoff_info): Clear adjust field.

        * aoutx.h (NAME(aout,find_nearest_line)): The caller expects
        functionname_ptr to be set to a symbol name, so prepend
        symbol_leading_char.

Thu Mar 24 11:33:46 1994  Steve Chamberlain  (sac@jonny.cygnus.com)

        * coff-h8300.c (h8300_reloc16_extra_cases): Add relaxing info
        for 16bit relative branches.
        * coff-h8500.c (r_high8, r_low16, r_high16): Don't complain on
        overflow.

Thu Mar 24 09:21:13 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_bfd_prep_for_ar_write): Ignore non-SOM objects.
        (som_bfd_ar_write_symbol_stuff, som_write_armap): Likewise.

Wed Mar 23 14:29:31 1994  David J. Mackenzie  (djm@rtl.cygnus.com)

        * netbsd386.c (N_SET_FLAGS): Delete the old definition.

Wed Mar 23 14:58:44 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Clean up the relaxing code for the new linker.
        * targets.c (_bfd_relax_section): Take boolean *again argument
        rather than asymbol list.
        * bfd.c (bfd_relax_section): Change name of fourth argument from
        symbols to again.
        * reloc.c (bfd_generic_relax_section): Take boolean *again
        argument rather than asymbol list.  Always return true.
        * bout.c: Include genlink.h.
        (aligncode, perform_slip): Declare.
        (perform_slip): Take BFD argument rather than asymbol list.
        Changed all callers.  Get the symbols from the BFD.  Change the
        hash table entry value as well as the symbol value.
        (abs32code): Take BFD argument rather than asymbol list.  Changed
        all callers.
        (aligncode): Likewise.
        (b_out_relax_section): Take boolean *again argument rather than
        asymbol list.  Only return false if an error occurred.  Set *again
        to false.  Get symbols from BFD.
        * reloc16.c: Include genlink.h.
        (bfd_perform_slip): Take BFD argument rather than asymbol list.
        Get the symbols from the BFD.  Change the hash table entry value
        as well as the symbol value.
        (bfd_coff_reloc16_relax_section): Take boolean *again argument
        rather than asymbol list.  Only return false if an error occurred.
        Set *again to false.  Get symbols from BFD.
        * coffcode.h (bfd_coff_backend_data): Change
        _bfd_coff_reloc16_estimate to take BFD argument rather than
        asymbol list.
        (bfd_coff_reloc16_estimate): Corresponding change.
        (dummy_reloc16_estimate): Corresponding change.
        * libcoff-in.h (bfd_coff_reloc16_relax_section): Change
        declaration to take boolean * rather than asymbol list.
        (bfd_perform_slip): Change declaration to take BFD rather than
        asymbol list.
        * coff-h8300.c (h300_reloc16_estimate): Take BFD argument rather
        than asymbol list.  Changed calls to bfd_perform_slip.
        * bfd-in2.h: Rebuilt.
        * libbfd.h: Rebuilt.
        * libcoff.h: Rebuilt.
        * Makefile.in: Rebuilt dependencies.

        * genlink.h (_bfd_generic_link_get_symbols): Define.
        (_bfd_generic_link_get_symcount): Define.
        * linker.c (generic_link_read_symbols): New function.
        (generic_link_add_object_symbols): Use it.  Use
        _bfd_generic_link_get_symbols and _bfd_generic_link_get_symcount
        to get the symbols from the BFD.
        (generic_link_check_archive_element): Likewise.
        (_bfd_generic_final_link): Likewise.
        (_bfd_generic_link_output_symbols): Likewise.
        (default_indirect_link_order): Likewise.
        (generic_link_add_symbol_list): Store pointer to hash table entry
        in asymbol udata field.

Tue Mar 22 13:09:44 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * coff-mips.c (mips_howto_table): Add entry for new MIPS_R_PCREL16
        reloc, used in embedded PIC code.
        (mips_adjust_reloc_in): Change sanity check to permit new reloc.
        (mips_bfd_reloc_type_lookup): Turn BFD_RELOC_16_PCREL_S2 into
        MIPS_R_PCREL16.

        * elf32-mips.c (mips_elf_final_link): Account for link_order
        relocs when allocating space for relocations.  Set SEC_RELOC flag
        for any section which has relocs.  Handle link_order relocs in
        link_order loop.  Use _bfd_generic_link_add_symbols_collect for
        add_symbls entry point.

        * linker.c (_bfd_generic_final_link): Set reloc_count to 0 before
        counting relocs.  Set SEC_RELOC flag for any section which has
        relocs.

        * linker.c (_bfd_default_link_order): Handle bfd_data_link_order.

        * linker.c (_bfd_generic_link_add_symbols): Just call
        generic_link_add_symbols.
        (_bfd_generic_link_add_symbols_collect): New function, like
        _bfd_generic_link_add_symbols but also collect constructors and
        destructors by name as collect2 does.
        (generic_link_add_symbols): New function, like old
        _bfd_generic_link_add_symbols but with collect argument.
        (generic_link_add_object_symbols): Take collect argument.
        (generic_link_check_archive_element_no_collect): New function.
        (generic_link_check_archive_element_collect): New function.
        (generic_link_check_archive_element): Take collect argument.
        (generic_link_add_symbol_list): Take collect argument.
        (_bfd_generic_link_add_one_symbol): Rename constructor argument to
        collect.
        * libbfd-in.h (_bfd_generic_link_add_symbols_collect): Declare.
        * libbfd.h: Rebuilt.

Tue Mar 22 10:04:00 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * archive.c (bfd_construct_extended_name_table): Use ar_padchar
        for first character in an extended name.
        (_bfd_write_archive_contents): If ar_padchar == '/', then use
        "//" as the name of the special archive member holding the
        extended name table.

Mon Mar 21 12:28:19 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Support for link_order types which generate relocs in order to
        support -Ur in the linker.
        * linker.c (generic_link_add_symbol_list): Remove bitsize argument
        from call to _bfd_generic_link_add_one_symbol.
        (_bfd_generic_link_add_one_symbol): Remove bitsize argument.
        Don't pass bitsize to constructor call back.  Pass BFD_RELOC_CTOR
        instead of bitsize to add_to_set call back.
        (_bfd_generic_final_link): Account for link_order relocs when
        allocating space for relocations.  Handle them in link_order loop.
        (_bfd_generic_reloc_link_order): New function.
        (_bfd_default_link_order): If a reloc_link_order is seen here,
        abort.
        (_bfd_count_link_order_relocs): New function.
        * libbfd-in.h (_bfd_generic_link_add_one_symbol): Remove bitsize
        argument from declaration.
        (_bfd_generic_reloc_link_order): Declare.
        (_bfd_count_link_order_relocs): Declare.
        * libbfd.h: Rebuilt.
        * aoutx.h (aout_link_add_symbols): Remove bitsize argument from
        call to _bfd_generic_link_add_one_symbol.
        (NAME(aout,final_link)): Account for link_order relocs when
        allocating space for relocations.  Handle them after handling all
        input BFDs.
        (aout_link_reloc_link_order): New function.
        * ecoff.c (ecoff_link_add_externals): Remove bitsize argument from
        call to _bfd_generic_link_add_one_symbol.
        (ecoff_bfd_final_link): Account for link_order relocs when
        allocating space for relocations.  Handle them in link_order loop.
        (ecoff_link_write_external): Set the storage class of a defined
        linker created symbol based on the section it is in.  Correct
        bfd_link_hash_weak case to use .sc rather than .st.
        (ecoff_reloc_link_order): New function.
        * coff-alpha.c (alpha_bfd_reloc_type_lookup): Handle
        BFD_RELOC_CTOR.
        * coff-mips.c (mips_bfd_reloc_type_lookup): Likewise.

        * sunos.c (sunos_read_dynamic_info): Remove unused locals dynsym
        and buf.

        * cisco-core.c (cisco_core_file_p): Only pass one argument to
        bfd_zmalloc.  Free a pointer, not a union.
        (cisco_bfd_is_local_label): Correct cast from asection to asymbol.

Sun Mar 20 09:24:36 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * bfd/som.c (som_begin_writing): Fix thinko (off by one error).

        * som.c (bfd_section_from_som_symbol): Only to do the value
        comparison for function symbols within executables.

        * som.c (bfd_section_from_som_symbol): Renamed from
        som_section_from_subspace_index.  Pass in a native SOM symbol.
        For executables, iterate through the sections to find out
        which contains the symbol's address rather than using the
        symbol_info field.  (symbol_info has a different meaning for
        dynamicly linked executables.)

        * trad-core.c (trad_unix_core_file_p): Don't pass abfd to
        bfd_zmalloc.

        * som.c (som_begin_writing): Fix braino (one call to align
        space/subspace data was done unconditionally rather than
        just for executables.)

        * som.c (som_begin_writing): Align text in all executables to
        make HPUX kernel happy.  Fixes strip/objcopy for shared
        executables.

Sat Mar 19 07:06:59 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_begin_writing): Account for alignment needs of
        subspaces too when writing executables.  Never request a negative
        bss size.  Fixes some problems with demand paged executables,
        still having problems with pure executables and shared executables.

Fri Mar 18 19:12:47 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * trad-core.c (trad_unix_core_file_p): Call bfd_zmalloc not
        bfd_zalloc for rawptr, because later on we may call free, not
        bfd_release, on it.

        * bfd.c (struct _bfd): Add cisco_core_struct to tdata union.
        * libbfd.c (bfd_read, bfd_seek): Add comments regarding errors.
        * cisco-core.c: New file.
        * Makefile.in: Change accordingly.
        * configure.in: Recognize cisco_core_vec.
        * config/m68k-aout.mt (SELECT_VECS): Add cisco_core_vec.
        * targets.c: Add cisco_core_vec.
        * bfd-in2.h: Rebuilt.

Fri Mar 18 18:13:49 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.h (som_copyable_section_data_struct): New structure
        containing all the private section information which needs
        to be copied from input section to output section during
        objcopy or strip.
        (som_section_data_struct): Remove several fields now in
        som_copyable_section_data_struct.  Make the space and 
        subspace dictionaries be pointers (to save space when
        only reading objects).

        * som.c (bfd_som_set_section_attributes): Now returns a boolean;
        some references changed.  Allocate a copyable data stucture if
        none exists.  Store info into the copyable data structure.
        (bfd_som_set_subsection_attributes): Likewise.
        (som_is_space, som_is_subspace, som_is_container): New functions.
        Use these instead of directly accessing private data.
        (som_prep_headers): Allocate space and subspace headers here.
        Fill in some fields in the space/subspace headers from the
        copyable data.
        (som_bfd_copy_private_section_data): Only copy the stuff
        that we really need to make objcopy and strip work.  Allocate
        the copy_data structure for the output bfd before copying.

        * som.h (struct som_exec_data): New structure to hold exec
        info that must be preserved when running objcopy/strip.
        (struct somdata): Add new "exec_data" field and accessor
        macro.  Add some comments on how the various fields are used.
        (som_section_data_struct): Make is_space and is_subspace bitfields.
        Delete unused subspace_index.  All references now use the
        target_index field within the section structure itself.

        * som.c (make_unique_section): Delete unused declaration.
        (som_bfd_copy_private_bfd_data): New function.
        (som_object_setup): Allocate space for and save exec information
        that needs to be copied during objcopy/strip.
        (som_mkobject): Do not allocate space for a file header here.
        It is not used when only reading SOM objects.
        (som_prep_headers): Allocate space for and attach a file header
        to the output bfd.  For executables, use the saved system_id
        value rather than trying to guess the right value.  Do not abort
        wwhen setting file_hdr->entry* for executables.
        (som_begin_writing): For executables, set the exec_entry and
        exec_flags fields.
        (som_copy_private_backend_section_data): Always return a value.

        * libhppa.h (PA_PAGESIZE): Define.

        * som.c (SOM_ALIGN): Define.
        (som_begin_writing): If writing an executable, initialize all
        fields in the exec header to zero.  Update fields in the exec
        header as sizes of loadable subspaces are computed.  Carefully
        preserve alignments when building executables.  Actually write the
        exec after all the fields are filled in.

        * Better long-filename handling.  Reads SOM ABI compliant extended
        names, but doesn't quite write compliant extended names yet.
        * som.c (som_slurp_extended_name_table): Delete function.  The
        generic code will handle things correctly.
        (som_slurp_armap): Seek to the beginning of the next member.
        (normalize): New function.
        (som_bfd_ar_write_symbol_stuff): Take the size of the extended
        name table into account when computing the file offsets in the
        SOM dictionary.  Make sure to align to an even boundary.
        (som_write_armap): Initialize the checksum to zero.
        (ar_maxchars): Fix.  Opps.

Fri Mar 18 20:35:24 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        * aoutx.h (reloc_type_lookup): Handle BFD_RELOC_CTOR on a 64-bit
        machine.  Handle BFD_RELOC_SPARC13 and BFD_RELOC_SPARC_BASE13.

Thu Mar 17 18:26:46 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        * bfd-in.h (BFD_VERSION): Use @VERSION@.
        * Makefile.in (bfd.h): Replace it with contents of VERSION file.
        * bfd-in2.h: Regenerated.

        * trad-core.c (trad_unix_bfd_is_local_label): Fixed typo where
        this was also named trad_unix_bfd_copy_private_bfd_data.

Thu Mar 17 10:37:07 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * aoutx.h, elfcode.h, coff-alpha.c, bout.c, ecoff.c, ecofflink.c,
        elf32-hppa.c, elf32-mips.c, linker.c, som.c, sunos.c: If malloc(0)
        returns NULL, it is not an error.  It's possible that some of
        these checks are not necessary (because the size can never be
        zero), but putting in the checks is the conservative thing to do
        in light of the fact that some of these malloc calls replaced
        unchecked alloca calls, in which a zero argument would work fine.

Thu Mar 17 11:44:45 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * osf-core.c (osf_core_bfd_copy_private_bfd_data): Remove
        duplicate definition.
        (osf_core_bfd_is_local_label): Define.

        * reloc.c (bfd_generic_get_relocated_section_contents): Don't fail
        if malloc (0) fails.  bfd_canonicalize_reloc returning 0 is not a
        failure indication, it merely means there are no relocs.

        * elfcode.h (NAME(bfd_elf,write_object_contents)): Don't use space
        after NAME, since SunOS /bin/cc can't handle it.

Wed Mar 16 16:43:33 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * netbsd386.c (N_SET_FLAGS): Don't nuke the machine id field.
        From sukes@glue.umd.edu (Tasuki Hirata).

Wed Mar 16 07:55:54 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * aoutf1.h (4 places): Use a simple #if on ARCH_SIZE, rather than
        all that convoluted stuff with NAME, CAT3, etc.  The convoluted
        stuff broke for SunOS4 /bin/cc (due to DEFUN elimination, I guess).

Wed Mar 16 00:02:05 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_prep_for_fixups): Detect section symbols based
        on either the lack of private data or the symbol flags.  Do not
        munge section symbol names anymore -- they no longer confuse GDB.
        (som_begin_writing): Leave space for an exec header if writing
        an executable.
        (som_slurp_symbol_table): Recognize both forms of section symbol
        names "L$0\002" and "$<FOO>$".  Change the name of "L$0\002"
        section symbols to be the name of the section they represent.
        Debugging  symbols begin with "L$0\001", not just "L$".

Tue Mar 15 22:58:28 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * bfd-in2.h, libbfd.h, libcoff.h: Rebuilt.

        * bfd-in.h (JUMP_TABLE): Add new entries to the jump table
        for bfd_copy_private_section_data, bfd_copy_private_bfd_data,
        and bfd_is_local_label.

        * targets.c: Add new entries to the bfd_target structure.
        
        * bfd.c (bfd_copy_private_bfd_data): New definition.

        * section.c (bfd_copy_private_section_data): New definition.

        * syms.c (bfd_is_local_label): New definition.

        * libbfd-in.h (bfd_generic_is_local_label): Declare.

        * libbfd.c (bfd_generic_is_local_label): New function.

        * *-core.c: Provide default definitions for new functions in
        the target vector which all point to bfd_false.

        * aout-target.h, coffcode.h, elf32-target.h elf64-target.h, ieee.c
        libaout.h, libecoff.h, nlm-target.h, oasys.c, srec.c, tekhex.c
        Default new vectors for copying private backend data to bfd_true.
        Default new vector for determining if a symbol is a local label
        to bfd_generic_is_local_label.

        * som.c (som_bfd_copy_private_section_data): New function.
        (som_bfd_is_local_label): New function.
        (som_bfd_copy_private_bfd_data): For now default to bfd_true.

        * elf32-hppa.c (hppa_elf_is_local_label): New function.

Tue Mar 15 23:55:47 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * cf-m68klynx.c (CALC_ADDEND): Use _bfd_m68klynx_howto_table.

Tue Mar 15 04:41:13 1994  David J. Mackenzie  (djm@rtl.cygnus.com)

        * Most files:
        Replace DEFUN and DEFUN_VOID with K&R-style function definition.
        Indent some of them to GNU standards.

        * aout32.c, archures.c, core.c, cpu-h8300.c, cpu-i960.c,
        cpu-m68k.c, cpu-m88k.c, cpu-mips.c, cpu-vax.c, ctor.c, demo64.c,
        elf32-hppa.h, gen-aout.c, host-aout.c, init.c, libhppa.h,
        libieee.h, liboasys.h, newsos3.c, som.h, stab-syms.c, sunos.c:
        Update copyright years.

Mon Mar 14 11:41:23 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_prep_for_fixups): A relocation involving the section
        symbol for the *ABS* section is really a relocation involving
        no symbol.
        (som_slurp_symbol_table): Do not set BSF_GLOBAL or BSF_EXPORT for
        undefined symbols.  Correctly distinguish between debugger symbols
        and section symbols.

        * som (setup_sections): Set SEC_DEBUGGING and the section attributes
        for spaces and subspaces.

        * som.c (som_bfd_count_ar_symbols): Fix typo.

        * som.c (som_object_setup): Set EXEC_P, D_PAGED, WP_TEXT, and
        HAS_RELOC based on the object's magic number.
        (make_unique_section): Delete function.  BFD and its users are
        prepared to handle multiple sections with the same name.
        (setup_sections): Allocate space on the BFD's obstack to hold
        section names.  Use bfd_make_setion_anyway rather than the
        obsolete make_unique_section.
        (som_prep_headers): Choose the correct SOM magic number based
        on the BFD's flags.
        (som_bfd_fill_in_ar_symbols): Return false, not NULL on error.

Sat Mar 12 09:46:09 1994  Ian Lance Taylor  (ian@cygnus.com)

        * elf32-ppc.c: Renamed from elf32-powerpc.c.
        * nlm32-ppc.c: Renamed from nlm32-powerpc.c.
        * Makefile.in, configure.in: Corresponding changes.

Fri Mar 11 22:27:19 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elf32-powerpc.c: Extensive changes to update to preliminary ABI.

Fri Mar 11 00:34:59 1994  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        * sunos.c (sunos_read_dynamic_info):  Assume that dynamic info
        is always located at the start of the data section to allow
        recovery of the dynamic info from a stripped executable.
        * ecoff.c (ecoff_styp_to_sec_flags):  Handle STYP_PDATA, STYP_XDATA
        and STYP_COMMENT.

Wed Mar  9 17:17:53 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * libbfd-in.h: Remove alloca cruft.  It was missing some necessary
        cruft (like the #pragma alloca for AIX).
        In addition to that problem, the C alloca calls xmalloc, which
        means checking for being out of memory can't work right.  The
        following changes remove all uses of alloca from BFD.
        * hosts/solaris2.h: Remove alloca cruft.
        * som.c: Replace alloca with a fixed size auto array.
        * aoutx.h, elfcode.h, nlmcode.h, bout.c, coff-alpha.c, ecoff.c,
        ecofflink.c, elf32-hppa.c, elf32-mips.c, linker.c, reloc.c, som.c,
        sunos.c: Replace alloca with malloc and appropriate error checking and
        freeing.
        * linker.c: Replace alloca with obstack_alloc.
        * libbfd.h: Rebuilt.

Tue Mar  8 12:10:38 1994  Ian Lance Taylor  (ian@cygnus.com)

        * coff-mips.c (mips_relocate_section): Handle MIPS_R_LITERAL like
        MIPS_R_GPREL.

Sat Mar  5 14:08:54 1994  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        * elf32-hppa.h, elfcode.h:  Replace uses of Elf*_Half, Elf*_Word,
        Elf*_Off typedefs by their expansion, the typedefs have been
        removed from include/elf/internal.h.
        * elfcode.h (bfd_section_from_shdr):  Handle SHT_DYNAMIC section like
        SHT_PROGBITS section.

Thu Mar  3 20:03:39 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.h (_PA_RISC_ID): Treat HOST_HPPAOSF just like HOST_HPPABSD.

Wed Mar  2 13:28:06 1994  Jim Kingdon  (kingdon@deneb.cygnus.com)

        * configure.host: Recognize i[34]86-sequent-*.

        * trad-core.c (trad_unix_core_file_p): A non-zero, not zero,
        return from bfd_seek indicates an error.
        New macro TRAD_CORE_DSIZE_INCLUDES_TSIZE to replace
        TRAD_CORE_STACK_OFFSET.
        * hosts/symmetry.h: Define TRAD_CORE_DSIZE_INCLUDES_TSIZE and
        TRAD_CORE_USER_OFFSET but not HOST_STACK_OFFSET.

Wed Mar  2 11:57:03 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.[ch]: Do not include libhppa.h in som.c, instead include
        it in som.h.

        * elf32-hppa.[ch]: Do not include libhppa.h in elf32-hppa.c, instead
        include it in elf32-hppa.h.

        * som.c (log2): Return -1 on error rather than aborting.
        (setup_sections): Bubble up an error from log2.

        * Changes to make HP C compiler happy in both traditional
        and ANSI mode.
        * som.c (hppa_som_gen_reloc_type): Use correct enum type for
        field parameter.
        (bfd_som_set_section_attributes): Use unsigned int rather than
        unsigned char to avoid GNU-C extensions.
        (bfd_som_attach_aux_hdr): Return a boolean to indicate success
        or failure rather than aborting on failure.

        * som.h (bfd_som_set_section_attributes): Fix prototype to match
        som.c changes.
        (bfd_som_attach_aux_hdr): Add prototype.
        (hppa_som-gen_reloc_type): Likewise.

        * elf32-hppa.c: Add a couple casts to make HP compiler happy.
        (hppa_look_for_stubs_in_section): Do not return false on failure
        until rest of code is ready to handle it.  Abort for now.

Tue Mar  1 18:33:59 1994  Jim Kingdon  (kingdon@deneb.cygnus.com)

        * bfd-in2.h: Rebuilt.

Tue Mar  1 13:06:53 1994  Kung Hsu  (kung@mexican.cygnus.com)

        * i386os9k.c: use new functions bfd_set_error and bfd_get_error.
        * Makefile.in: delete an extra blank.
        * configure.in : Add i396os9k_vec.

Mon Feb 28 15:41:01 1994  Kung Hsu  (kung@mexican.cygnus.com)

        * config.bfd : Add i386-os9k.
        * config/i386-os9k.mt : Newly add os9k target makefile.

        * i386os9k.c : new file to handle os9k format bfd.
        * Makefile.in : Handle new file i386os9k.c
        * targets.c : Add bfd_target_os9k_flavour and i386os9k_vec.
        * cache.c : Initialize cache_sentinel to 0.

Sun Feb 27 16:30:55 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * elf32-hppa.c (mismatches, retval_mismatches): Fix mismatch
        action in case where caller specified no argument relocation.
        (hppa_elf_build_linker_stub): Try again to get the sym_ptr_ptr
        right in the original relocation and the stub's relocation.

        * elf32-hppa.h (hppa_look_for_stub_in_section): Fix typo.  Delete
        unused symbols argument.

        * elf32-hppa.c (hppa_elf_stub_reloc): Accept asymbol ** rather
        than asymbol * for original target symbol.  All callers changed.
        Set reloc->sym_ptr_ptr appropriately.
        (hppa_elf_build_linker_stub): Set reloc->sym_ptr_ptr correctly.
        (hppa_elf_look_for_stubs_in_section): No longer need symbols
        argument.  Use the output symbols when canonicalizing the relocs,
        creating them if necessary.

        * linker.c (_bfd_generic_link_output_symbols): Do not
        rebuild/clobber the output symbols if they already exist.

Sun Feb 27 15:22:36 1994  Stan Shebs  (shebs@andros.cygnus.com)

        * targets.c (BFD_SEND, BFD_SEND_FMT): Add debugging versions that
        check all the pointer dereferences.  Enabled via DEBUG_BFD_SEND.
        * bfd-in2.h: Rebuilt.

        * srec.c (hex_value): Always set to a size of 256 bytes.
        (srec_init): Cosmetic changes.

Sun Feb 27 11:18:47 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * elf32-hppa.c: Second half of major cleanup.  More comments,
        PARAMize and staticize rest of functions.  Delete unused
        functions.  Delete unused/unnecessary arguments to some functions.
        Group static vars together.  Abort for bad errors until we have
        error code propogation working.  Work on spacing and indention.
        Add FIXMEs for unresolved problems.  Use enums rather than
        #defines for lots of things.  Merge two functions which build
        linker stubs into a single function (so they can easily share a
        ton of common code).

Sat Feb 26 10:00:45 1994  Ian Lance Taylor  (ian@cygnus.com)

        * reloc.c (_bfd_relocate_contents): Adjust handling of overflow to
        avoid depending upon right shifts of signed numbers, and to
        correct handling of src_mask with lower bits zero.

        * aoutx.h, archive.c: Add casts to avoid warnings from SVR4 cc.
        * ecoff.c, ecofflink.c, ecoffswap.h, srec.c: Likewise.
        * elf32-i386.c: Likewise.
        * elfcode.h (bfd_section_from_shdr): Make i unsigned; remove old
        #if 0 code.
        (elf_write_phdrs): Make i unsigned.
        (map_program_segments): Make i and n_left unsigned.
        (assign_file_positions_except_relocs): Make i unsigned.
        (write_shdrs_and_ehdr): Make count unsigned.
        (assign_file_positions_for_relocs): Make i unsigned.
        (NAME(bfd,elf_write_object_contents)): Make count unsigned.
        (section_from_elf_index): Make index argument unsigned.

Fri Feb 25 21:34:58 1994  Ian Lance Taylor  (ian@cygnus.com)

        * elfcode.h: Don't include assert.h.
        (swap_out_syms): Use BFD_ASSERT rather than assert.

        * linker.c (_bfd_generic_link_write_global_symbol): Add missing
        break in switch.

        * hosts/i386v4.h (qsort, strtol): Remove incorrect and useless
        declarations.

Fri Feb 25 16:35:57 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * libhppa.h (hppa_rebuild_insn): Moved here from elf32-hppa.c.

        * elf32-hppa.h (elf_hppa_tc_symbol): Add new arguments.
        (elf_hppa_tc_make_sections): Likewise.
        (elf_hppa_final_processing): Add extern decl.

        * elf32-hppa.c: First half of major cleanup.  Add/cleanup lots of
        comments.  PARAMize some static functions.  Delete unused functions.
        Delete unused/unnecessary arguments to many functions.  Group
        static vars together.  Collapse common case statements together
        in many places.  Use default case when possible instead of listing
        each case separately.  Abort for bad errors until we get error
        code propogation working.  Work on spacing and indention problems.
        Add FIXMEs for some unresolved problems.  Delete hopelessly broken 
        COMPLEX relocation support (it's never used anyway).
        (hppa_elf_rebuild_insn): Delete.  Moved into libhppa.h.
        (elf_hppa_tc_symbol): Accept and use new arguments (symext chains).
        (elf_hppa_tc_make_sections): Likewise.

        * format.c (bfd_check_format_matches): Initialize matching_vector
        to keep gcc -Wall quiet.

        * elfcode.h (elf_slurp_reloca_table): Fix typo.

        * som.c (som_get_symtab_upper_bound): Use "sizeof (asymbol *)"
        not "sizeof (som_symbol_type *)".

        * elfcode.h (elf_get_symtab_upper_bound): Use "sizeof (asymbol *)"
        not "sizeof (asymbol").  Opps.

Fri Feb 25 13:19:04 1994  Ted Lemon  (mellon@pepper.ncd.com)

        * bfd.c (bfd_get_gp_size): Can't return gp value on an archive.
        (bfd_set_gp_size):  Can't set gp value on an archive.

Fri Feb 25 12:57:00 1994  Steve Chamberlain  (sac@jonny.cygnus.com)

        * srec.c (pass_over): Don't skip too many characters when
        end of line seen.

Fri Feb 25 11:41:57 1994  Ian Lance Taylor  (ian@cygnus.com)

        * ecoff.c (ecoff_sizeof_headers): Align result to 16 byte
        boundary.

Thu Feb 24 07:13:22 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_bfd_derive_misc_symbol_info): Derive symbol_info
        field for absolute symbols in the same manner as undefined
        and common symbols.

Thu Feb 24 04:29:19 1994  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        * elfcode.h (elf_core_file_p):  Check for core file e_machine match
        like in elf_object_p.

Wed Feb 23 18:28:37 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * elfcode.h (alloca): Delete declaration.

        * som.c (som_prep_headers): Use CPU_PA_RISC1_0 for magic
        number rather than HP9000S800_ID.  Note som.c is careful
        to make sure CPU_PA_RISC1_0 is always defined.

Mon Feb 21 10:12:02 1994  Stan Shebs  (shebs@andros.cygnus.com)

        * Makefile.in (targets.o, archures.o): Use ALL_CFLAGS to supply
        flags to explicit compile actions.

Mon Feb 21 09:50:06 1994  Ian Lance Taylor  (ian@lisa.cygnus.com)

        * ecofflink.c (ecoff_write_symhdr): Set symhdr->magic here.
        * ecoff.c (ecoff_write_object_contents): Make sure .bss section
        ends on a page boundary if there is no symbol table.
        (ecoff_bfd_final_link): Don't set symhdr->magic here.

        * hosts/hp300.h: Include <stdlib.h>; don't declare free.

        * som.c (som_bfd_count_ar_symbols): Use a pointer and alloca
        rather than an array of variable size.
        (som_bfd_fill_in_ar_symbols): Likewise.
        (som_bfd_ar_write_symbol_stuff): Likewise.

        * coff-alpha.c (alpha_relocate_section): Rewrite mask and shift
        operation to avoid OSF 1.3 cc bug.
        * ecoff.c (ecoff_write_object_contents): Make text_size, data_size
        and bss_size bfd_size_type instead of unsigned long.  Make
        text_start and data_start bfd_vma instead of unsigned long.
        * ecofflink.c (ecoff_add_string): Remove incorrect cast of return
        value.

Sun Feb 20 16:06:54 1994  Ian Lance Taylor  (ian@lisa.cygnus.com)

        * linker.c (_bfd_generic_link_add_archive_symbols): Consider
        symbols in the order they appear in the archive map.

Sat Feb 19 03:17:32 1994  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        * coff-alpha.c (reloc_nil):  Add forward declaration, add missing
        error_message argument.
        * coff-sparc.c (bfd_coff_generic_reloc):  Add forward declaration,
        add missing error_message argument.
        * mipsbsd.c (mips_fix_hi16_s):  Add forward declaration, add missing
        error_message argument.

Fri Feb 18 11:41:58 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Support for PowerPC NetWare.
        * nlm32-powerpc.c: New file.
        * config.bfd (powerpc-*-netware*): New target; use ppc-nlm.
        * config/ppc-nlm.mt: New file.
        * configure.in (nlm32_powerpc_vec): New target vector; use
        nlm32-powerpc.o, nlm32.o, nlm.o.
        * targets.c (nlm32_powerpc_vec): Declare.
        * Makefile.in (BFD32_BACKENDS): Add nlm32-powerpc.o.
        (CFILES): Add nlm32-powerpc.c.

        Initial support for PowerPC ELF.  Done without an ABI, and
        probably to be changed when I get an ABI.
        * config.bfd (powerpc-*-sysv4*): New target; use ppc-elf.
        * config/ppc-elf.mt: New file.
        * configure.in (bfd_elf32_powerpc_vec): New target vector; use
        elf32-powerpc.o, elf32.o, elf.o.
        * elf32-powerpc.c: New file.
        * elfcode.h (prep_headers): Add bfd_arch_powerpc case.
        (elf_set_arch_mach): Likewise.
        * targets.c (bfd_elf32_powerpc_vec): Declare.
        * Makefile.in (BFD32_BACKENDS): Add elf32-powerpc.o.
        (CFILES): Add elf32-powerpc.c.
        Rebuilt dependencies.

Thu Feb 17 15:29:55 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * coffgen.c (coff_write_linenumbers): Always return a value.

        * elfcode.h (elf_slurp_symbol_table): Handle zero symbols
        reasonably.  Allocate x_symp using alloca.

        * elfcode.h (map_program_segments): ELF program header entries
        must be sorted by load address.  This used to generate the entries
        in reverse order.

        * section.c (SEC_IN_MEMORY): Define.
        (asection): Rename unused field otheruserdata to contents, and
        make it char *.
        (bfd_make_section_anyway): Initialize contents field to NULL.
        (bfd_get_section_contents): If SEC_IN_MEMORY is set, get section
        contents from contents field rather than from file.
        * bfd-in2.h: Rebuilt.

Thu Feb 17 08:30:53 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * bfd.c (bfd_get_error, bfd_set_error): New functions.
        (bfd_error): Make static.
        (bfd_error_type): Renamed from bfd_ec.  Prepend "bfd_error_" to
        all values.
        * bfd-in2.h: Regenerated.
        * aix386-core.c, aout-adobe.c, aout-encap.c, aout-target.h, 
        aoutf1.h, aoutx.h, archive.c, archures.c, 
        bfd.c, bout.c, cache.c, coff-alpha.c, coff-mips.c, 
        coff-rs6000.c, coffcode.h, coffgen.c, core.c, ctor.c, 
        ecoff.c, ecofflink.c, elf.c, elf32-hppa.c, elf32-mips.c, 
        elfcode.h, format.c, hash.c, hp300hpux.c, hppabsd-core.c, 
        i386lynx.c, ieee.c, libbfd.c, libelf.h, linker.c, 
        lynx-core.c, nlm.c, nlm32-alpha.c, nlm32-i386.c, 
        nlm32-sparc.c, nlmcode.h, oasys.c, opncls.c, osf-core.c, 
        ptrace-core.c, reloc16.c, rs6000-core.c, section.c, som.c, 
        srec.c, sunos.c, syms.c, targets.c, tekhex.c, 
        trad-core.c: Change callers.

Tue Feb 15 22:27:27 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c: Remove FIXMEs for things which have been dealt with.

Tue Feb 15 19:39:24 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        * section.c (bfd_get_section_contents): Since this function reads
        unrelocated contents, the section's raw size is always the one to
        use for bounds checking.

        * linker.c (default_indirect_link_order): In assertion, compare
        link_order size field against cooked size, not raw size, of input
        section.

        * bout.c (b_out_get_reloc_upper_bound): For BSS section, just
        return 0.
        (aligncode): When shrinking, the addend should be set to the
        current offset in the section plus the number of bytes of padding
        that will actually be retained.
        (b_out_relax_section): If a section contains no relocations, don't
        bother processing them.
        (b_out_get_relocated_section_contents): Set reloc_done.  Assert
        that bfd_get_section_contents returns true.  Check that relocs are
        properly ordered.
        (b_out_get_relocated_section_contents, case ALIGNDONE): Assert
        that reloc->addend falls between the current source offset and the
        raw size of the input section.

        * config.bfd: Support i960 vxworks versions > 5.0 with coff, not
        bout.  Default with no version number is still bout.  Support
        explicit i960-coff target too.

        * bout.c: Changed some indentation, deleted trailing whitespace,
        fixed some comments, removed some "#if 1" lines.
        (output_addr): New macro.
        (calljx_callback, callj_callback, get_value, abs32code, aligncode,
        b_out_get_relocated_section_contents): Use it for readability.

Tue Feb 15 09:00:16 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_bfd_prep_for_ar_write): Iterate through the SOM
        symbols, not the BFD symbols.
        (som_bfd_ar_write_symbol_stuff): Likewise.

Mon Feb 14 22:55:20 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_slurp_symbol_table): Do not die if a BFD doesn't
        have any symbols.

        * Finish basic read-write support for SOM archive libraries.  Bugs
        surely remain as this hasn't been tested all that much.
        * som.c (SOM_LST_HASH_SIZE, SOM_LST_MODULE_LIMIT): Define.
        (struct som_misc_symbol_info): New structure to hold info necessary
        to build both normal and library symbol tables.
        (som_derive_misc_symbol_info): New function to derive info necessary
        to build both normal and library symbol tables.
        (som_build_and_write_symbol_table): Use new function to derive misc
        symbol information.
        (som_slurp_symbol_table): Update backend private data for symbols
        appropriately.
        (som_bfd_prep_for_ar_write): New function.
        (som_bfd_ar_symbol_hash): New function.
        (som_bfd_ar_write_symbol_stuff): New function.
        (som_write_armap): Flesh out.
        (som_vec): Fix ar padding character.

        * som.c: Consistently use memset rather than bzero.

Mon Feb 14 17:02:28 1994  Stu Grossman  (grossman at cygnus.com)

        * coff-rs6000.c:  Add Lynx core file support, use HOST_AIX, where
        appropriate.
        * rs6000-core.c:  Use HOST_AIX instead of COREFILES_PLEASE.
        * config/rs6000.mh:  Remove defs of ARCHIVES_PLEASE and
        COREFILES_PLEASE.
        * config/rs6000lynx.mh:  Turn on Lynx core file support.
        * hosts/rs6000.h:  #define HOST_AIX.
        * hosts/rs6000lynx.h:  Create this to enable Lynx host support.

Sun Feb 13 14:30:00 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.h (som_symbol_data): Safely access backend private data
        for BFD symbols.  All callers changed.

        * Read-only SOM archive support.
        * som.c (som_bfd_count_ar_symbols): New helper function.
        (som_bfd_fill_in_ar_symbols): New helper function.
        (som_slurp_armap): New function to read a SOM LST.

        * som.h: Include <lst.h> and <ar.h>.

Sat Feb 12 22:34:14 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * elfcode.h (elf_map_symbols): Fix typo.
        (write_object_contents): Check return values from prep_headers and
        elf_compute_section_file_positions.
        (set_section_contents): Likewise.

Fri Feb 11 16:56:50 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * archive.c (normalize) [VMS]: Call malloc, not bfd_xmalloc.
        (bfd_construct_extended_name_table): Check result of normalize.

Tue Feb  8 08:57:31 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        Make all callers of malloc or realloc (including via obstacks)
        check the result for NULL.  Most set bfd_error to no_memory and
        return in that case; a few are harder to fix, and are marked
        with "FIXME <return type>".

        * elf32-hppa.c (hppa_elf_build_arg_reloc_stub
        hppa_elf_build_long_branch_stub):  Check bfd_make_empty_symbol return.
        * linker.c (_bfd_generic_link_output_symbols
        _bfd_generic_link_write_global_symbol): Ditto
        * section.c (bfd_make_section_anyway): Ditto.

        * tekhex.c (find_chunk tekhex_mkobject): Check bfd_alloc.
        (first_phase): Ditto.  FIXME void
        (tekhex_make_empty_symbol): Check bfd_zalloc.

        * sunos.c (sunos_read_dynamic_info): Check bfd_zalloc.
        (MY(read_dynamic_symbols) MY(read_dynamic_relocs)): Check bfd_alloc.

        * stringhash.c (_bfd_stringtab_hash_newfunc): Check bfd_hash_allocate.

        * srec.c: Indent.
        (fillup_symbols): Check bfd_alloc.  FIXME void
        (srec_mkobject srec_get_section_contents
        srec_set_section_contents): Check bfd_alloc. 
        (srec_make_empty_symbol): Check bfd_zalloc.

        * som.c (hppa_som_gen_reloc_type): Check bfd_alloc_by_size_t.
        (make_unique_section): Check bfd_alloc.
        (som_new_section_hook): Check bfd_zalloc.
        (bfd_som_attach_aux_hdr): Ditto.  FIXME void

        * rs6000-core.c (rs6000coff_core_p): Check bfd_zalloc.

        * osf-core.c (osf_core_make_empty_symbol): Check bfd_zalloc.
        (osf_core_core_file_p): Check bfd_alloc.

        * oasys.c (oasys_slurp_symbol_table oasys_archive_p
        oasys_mkobject oasys_object_p oasys_new_section_hook
        oasys_set_section_contents): Check bfd_alloc.
        (oasys_slurp_section_data): Check bfd_zalloc and bfd_alloc.
        (oasys_make_empty_symbol): Check bfd_zalloc.

        * nlmcode.h (nlm_make_empty_symbol): Check bfd_zalloc.
        (nlm_slurp_symbol_table): Check bfd_zalloc and bfd_alloc.

        * nlm32-sparc.c (nlm_sparc_read_import): Check bfd_alloc.

        * nlm32-i386.c (nlm_i386_read_import): Check bfd_alloc.

        * nlm32-alpha.c (nlm_alpha_read_import): Check bfd_alloc.

        * linker.c (_bfd_link_hash_newfunc
        (generic_link_hash_newfunc
        (archive_hash_newfunc
        (_bfd_generic_link_add_one_symbol): Check bfd_hash_allocate.
        (_bfd_generic_final_link
        (_bfd_generic_link_output_symbols
        (default_indirect_link_order): Check bfd_alloc.
        (bfd_new_link_order): Check bfd_alloc_by_size_t.

        * irix-core.c (irix_core_make_empty_symbol): Check bfd_zalloc.

        * ieee.c: Indent.
        (read_id get_symbol get_section_entry ieee_archive_p ieee_object_p
        ieee_slurp_section_data ieee_new_section_hook): Check bfd_alloc.
        (do_one): Check bfd_alloc.  Return a boolean.
        (ieee_slurp_section_data): Check it.
        (init_for_output): Check bfd_alloc.  Return a boolean.
        (ieee_set_section_contents): Check it.
        (do_with_relocs):  Check bfd_alloc.  Return a boolean.
        (ieee_bfd_debug_info_accumulate): Ditto.  FIXME void.
        (ieee_mkobject): Check bfd_zalloc.
        (ieee_make_empty_symbol): Check bfd_zmalloc.

        * hpux-core.c (hpux_core_make_empty_symbol): Check
        bfd_zalloc.

        * hppabsd-core.c (hppabsd_core_make_empty_symbol): Check
        bfd_zalloc.
        (hppabsd_core_core_file_p): Check bfd_zalloc.

        * hp300hpux.c (MY(slurp_symbol_table)): Check bfd_alloc.

        * elfcode.h (elf_new_section_hook): Check bfd_alloc.
        (bfd_section_from_phdr): Ditto.
        (write_relocs): Ditto.  FIXME void
        (elf_map_symbols assign_section_numbers map_program_segments):
        Ditto.  Return a boolean. 
        (swap_out_syms): Ditto.  Check elf_map_symbols.
        (elf_slurp_symbol_table): Check bfd_zalloc.
        (elf_slurp_reloca_table): Check bfd_alloc.
        (elf_slurp_reloc_table): Ditto.
        (elf_compute_section_file_positions): Check assign_section_numbers.
        (assign_file_positions_except_relocs): Return a boolean.
        Check map_program_segments.
        (elf_compute_section_file_positions): Check it.

        * elf32-mips.c (mips_elf_final_link): Check bfd_alloc.

        * elf32-hppa.c (hppa_elf_stub_branch_reloc): Check bfd_zmalloc and
        realloc. 
        (hppa_elf_stub_reloc): Ditto.
        (hppa_elf_build_arg_reloc_stub): Check bfd_zalloc.
        (hppa_elf_build_long_branch_stub): Ditto.
        (elf32_hppa_backend_symbol_table_processing): Ditto.

        * ecoff.c (ecoff_set_symbol_info): Check bfd_alloc.  Return a boolean.
        (ecoff_slurp_symbol_table): Check it.
        (ecoff_slurp_armap): Check bfd_alloc.
        (ecoff_write_armap): Check bfd_zalloc.
        (ecoff_link_hash_newfunc): Check bfd_hash_allocate and
        _bfd_link_hash_newfunc. 
        (ecoff_link_add_externals): Check bfd_alloc.

        * ctor.c (bfd_constructor_entry): Check bfd_alloc.

        * coffgen.c (coff_real_object_p): Check bfd_alloc.
        (coff_renumber_symbols): Check bfd_alloc_by_size_t.  Return a boolean.
        (coff_write_symbol): Check bfd_alloc.  FIXME int
        (coff_write_linenumbers): Check bfd_alloc.  Return a boolean.
        (coff_section_symbol): Check bfd_alloc_by_size_t.
        (coff_get_normalized_symtab): Check bfd_alloc.
        (coff_bfd_make_debug_symbol): Check bfd_zalloc.
        * libcoff-in.h: Change decls of coff_renumber_symbols,
        coff_write_linenumbers.
        * libcoff.h: Rebuilt.
        * coffcode.h (coff_write_object_contents): Check
        coff_renumber_symbols, coff_write_linenumbers.

        * coffcode.h: Indent.
        (coff_add_missing_symbols): Check bfd_alloc_by_size_t.  Return a
        boolean. 
        (coff_write_object_contents): Check it.

        * coff-alpha.c (alpha_relocate_section): Check bfd_alloc.
        * coff-mips.c (mips_relocate_section): Ditto.

        * archive.c (bfd_slurp_bsd_armap_f2): Check bfd_alloc value.
        (do_slurp_bsd_armap): Ditto.
        (compute_and_write_armap): Check bfd_realloc value.

        * aoutx.h (translate_from_native_sym_flags): Check bfd_alloc
        return value.  Return boolean value.
        (NAME(aout,make_empty_symbol)): Check bfd_zalloc return value.
        (NAME(aout,slurp_symbol_table)): Check bf_alloc and bfd_zalloc
        return value.
        (add_to_stringtab): Ditto.  FIXME void
        (aout_link_hash_newfunc): Check bfd_hash_allocate return value.
        (aout_link_add_symbols): Check bfd_alloc value.
        (translate_symbol_table): Check translate_from_native_sym_flags.
        * hp300hpux.c (MY(slurp_symbol_table)): Ditto.
        * aoutx.h (aout_link_hash_newfunc): Check _bfd_link_hash_newfunc.

        * opncls.c (bfd_zalloc bfd_realloc): Check result of bfd_alloc.

        * opncls.c (obstack_chunk_alloc): Define as malloc, not
        bfd_xmalloc_by_size_t. 
        (_bfd_new_bfd): Check obstack_begin for 0 return.

        * ieee.c (obstack_chunk_alloc): Define as malloc, not
        bfd_xmalloc_by_size_t. 
        (ieee_archive_p): Check obstack_begin for 0 return and
        obstack_finish for NULL return.

        * hash.c (obstack_chunk_alloc): Define as malloc, not
        bfd_xmalloc_by_size_t. 
        (bfd_hash_table_init_n): Check obstack_begin for 0 return and
        obstack_finish for NULL return.
        (bfd_hash_lookup): Check obstack_alloc for NULL return.

        * ecofflink.c (obstack_chunk_alloc): Define as malloc, not
        bfd_xmalloc_by_size_t. 
        bfd_ecoff_debug_accumulate
        bfd_ecoff_debug_accumulate_other): Check obstack_alloc.
        (add_file_shuffle add_memory_shuffle): Check obstack_alloc for
        NULL return.  Return boolean, not void.
        (bfd_ecoff_debug_init): Check obstack_begin for 0 return.
        (bfd_ecoff_debug_accumulate): Check add_file_shuffle
        and add_memory_shuffle return. 
        (string_hash_newfunc): Check bfd_hash_allocate and bfd_hash_newfunc.
        (bfd_ecoff_debug_accumulate): Check bfd_alloc.
        (ecoff_add_string): Check add_memory_shuffle return.

        * libbfd-in.h (xmalloc, bfd_xmalloc, bfd_xmalloc_by_size_t):
        Remove decls. 
        * libbfd.h: Rebuilt.

Fri Feb 11 15:35:32 1994  Stu Grossman  (grossman at cygnus.com)

        * configure.host:  Add Lynx/rs6000 support.
        * config/i386-nlm.mt:  Enable a.out file support.
        * config/rs6000lynx.mh:  Lynx/rs6000 host support.

Fri Feb 11 17:25:58 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * archive.c (compute_and_write_armap): Rewrite somewhat to improve
        memory usage.

Fri Feb 11 13:10:42 1994  Stan Shebs  (shebs@andros.cygnus.com)

        * archive.c: Change all references to '\n' in archive magic
        to '\012', for greater portability.
        * ecoff.c (ecoff_write_armap): Ditto.

Thu Feb 10 12:58:48 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aoutx.h (aout_link_write_other_symbol): Check strip settings to
        see whether symbol should be output.
        * genlink.h (struct generic_write_global_symbol_info): Added info
        field.
        * linker.c (_bfd_generic_final_link): Initialize wginfo.info.
        (_bfd_generic_link_write_global_symbol): Check strip settings to
        see whether symbol should be output.
        * elf32-mips.c (mips_elf_final_link): Initialize wginfo.info.

Wed Feb  9 21:34:58 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_reloc_queue_find): Do not examine a NULL queue entry.

        * som.c: Cast return values from BFD memory allocation routines to
        avoid warnings from the HP compiler.

Wed Feb  9 12:55:02 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * coff-alpha.c (alpha_relocate_section): Accept a LITERAL
        reloc on an "ldl" instruction too.

        * archive.c (bfd_ar_hdr_from_filesystem): Cast status elements
        when passing them to sprintf.  Use %ld instead of %d.

        * coff-rs6000.c (rs6000coff_mkarchive): Return false.
        (rs6000_coff_snarf_ar_hdr): Don't declare errno; it's not used.
        Also removed unused variable namelen.
        (rs6000coff_write_armap): Declare orl_count and stridx parameters.

Tue Feb  8 18:00:34 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * libbfd-in.h (xmalloc): Don't declare parameter type, to avoid
        conflicts.
        * libbfd.h: Rebuilt.

Tue Feb  8 15:55:50 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        * coff-alpha.c (reloc_nil): New function.
        (alpha_howto_table): Use it as special_function to prevent certain
        relocs from being adjusted by bfd_perform_relocation.  IGNORE
        reloc should be partial_inplace.
        (alpha_ecoff_get_relocated_section_contents): Accept a LITERAL
        reloc on an "ldl" instruction too.

Tue Feb  8 00:32:28 1994  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        * elf32-hppa.c (CURRENT_STUB_OFFSET, hppa_elf_build_arg_reloc_stub,
        hppa_elf_build_long_branch_stub):  Cast to char * instead of int
        before performing pointer arithmetic.

Mon Feb  7 20:56:27 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * config.bfd (hppa*-*-osf*): Use bfd_name hppaosf for this
        configuration.
        (hppa*-*-*elf*): This configuration used hppa-elf now.

        * som.c: This file is also used for HOST_HPPAOSF.

        * targets.c (bfd_target_vector): Enable som_vec for HOST_HPPAOSF.

        * hosts/hppaosf.h: New host configuration file.

        * config/hppabsd.mt (SELECT_VECS): Add bfd_elf32_hppa_vec as
        BSD handles both SOM and ELF object files.

        * config/hppaosf.mh (HDEFINES): Delete.  No longer needed.
        (RANLIB): Doesn't do anything, define it to be "echo".

        * config/hppaosf.mt: New target makefile fragment for a PA running
        OSF1.

Mon Feb  7 15:02:06 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * archures.c (enum bfd_architecture): Added bfd_arch_powerpc.
        (archures_init_table): If SELECT_ARCHITECTURES is not defined,
        added bfd_powerpc_arch.
        * bfd-in2.h: Rebuilt.
        * cpu-powerpc.c: New file.
        * Makefile.in (ALL_MACHINES, CFILES): Added cpu-powerpc.c.
        Rebuilt dependencies.

        * elfcode.h (bfd_section_from_shdr): Get vma and alignment_power
        of an SHT_STRTAB section from sh_addr and sh_addralign, rather
        than just setting them to zero.

Sun Feb  6 20:04:10 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * elfcode.h (prep_headers, swap_out_syms): Check for NULL return
        from bfd_new_strtab. 
        (elf_compute_section_file_positions): Check for false return from
        swap_out_syms. 

        * linker.c (default_indirect_link_order): Check for NULL return
        from bfd_get_relocated_section_contents.

        * syms.c: Make example application in doc call xmalloc, not
        bfd_xmalloc. 

        * aoutx.h (NAME(aout,slurp_symbol_table),
        aout_link_get_symbols, NAME(aout,link_hash_table_create)):
        * bout.c (b_out_slurp_reloc_table, b_out_squirt_out_relocs):
        * ecoff.c (ecoff_bfd_link_hash_table_create): 
        * ecofflink.c (bfd_ecoff_debug_init): 
        * format.c (bfd_check_format_matches): 
        * linker.c (_bfd_generic_link_hash_table_create): 
        (_bfd_generic_final_link): 
        * reloc16.c (bfd_coff_reloc16_relax_section): 
        (bfd_coff_reloc16_get_relocated_section_contents): 
        * elf32-hppa.c (hppa_elf_build_arg_reloc_stub): 
        * elf32-mips.c (mips_elf_final_link): 
        * elfcode.h (bfd_new_strtab): 
        (bfd_add_2_to_strtab): 
        (elf_slurp_symbol_table): 
        (elf_corefile_note): 
        * libbfd.c (bfd_zmalloc): 
        Use malloc and check the result, instead of bfd_xmalloc.

Sat Feb  5 12:39:28 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * config.bfd: Put m68*-*-sysv* line after m68*-*-sysv4*.

Sat Feb  5 05:32:44 1994  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        * srec.c (srec_write_record):  Put CONST keyword for "src" before
        "unsigned", some compilers don't like it after "unsigned".
        * libcoff.h, libcoff-in.h (bfd_perform_slip):  Rename "value" to
        "val" in prototype declaration because some compilers don't like
        arguments whose names are the same as types.

Sat Feb  5 01:14:38 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aoutx.h (aout_link_check_ar_symbols): Correct test for whether
        object file defines symbol.  Also, if skipping a symbol, skip the
        second symbol of a N_WARNING or N_INDR symbol as well.

Fri Feb  4 23:55:44 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Add basic support for writing RS/6000 XCOFF files.
        * coff-rs6000.c (dummy_reloc): Removed.
        (rs6000coff_howto_table): Defined XCOFF relocs.
        (RTYPE2HOWTO): Defined to use rs6000coff_rtype2howto.
        (rs6000coff_rtype2howto): New function.
        (coff_bfd_reloc_type_lookup): Defined to use
        rs6000coff_reloc_type_lookup. 
        (rs6000coff_reloc_type_lookup): New function.
        (SELECT_RELOC): Defined to set r_type and r_size fields.
        (COFF_LONG_FILENAMES): Defined.
        * coffcode.h (combined_entry_type): Changed fix_tag and fix_end
        fields to bitfields.  Added fields fix_value and fix_scnlen.
        (sec_to_styp_flags): If STYP_DEBUG is defined, use it rather than
        STYP_INFO for the type of a section named .debug.
        (coff_add_missing_symbols): Don't define if RS6000COFF_C.
        (coff_write_object_contents): If RS6000COFF_C, don't call
        coff_add_missing_symbols.
        (coff_slurp_symbol_table): If RS6000COFF_C, then if the last aux
        entry has type STY_LD change the x_scnlen into a pointer to a
        symbol and set fix_scnlen.  Also, for a C_BSTAT symbol, change the
        value into a pointer to a symbol and set fix_value.
        * libcoff.h: Rebuilt.
        * coffgen.c (coff_mangle_symbols): Reindent.  If fix_value is set,
        get the symbol offset. Likewise for fix_scnlen.
        (string_size): Change type to bfd_size_type.
        (debug_string_size, debug_string_section): New static variables.
        (coff_fix_symbol_name): If bfd_coff_symname_in_debug returns true,
        write the symbol name into the .debug section; assume that the
        section has already been created with the right size.
        (coff_write_symbols): Initialize debug_string_size to 0.  If
        bfd_coff_symname_in_debug returns true, don't put symbol name in
        usual string table.  After writing out all symbols, if
        debug_string_size is not 0, check that it matches the size of the
        .debug section.
        (coff_get_normalized_symtab): Clear new fix_value and fix_scnlen
        fields.  If the string offset is 0, always use an empty string as
        the name.
        (coff_make_empty_symbol): Zero out the symbol structure.
        * reloc.c (bfd_perform_relocation): Work around one gross hack
        with another: actually look at the target name to avoid the broken
        COFF check.
        (bfd_reloc_code_real_type): Add BFD_RELOC_PPC_B26,
        BFD_RELOC_PPC_BA26 and BFD_RELOC_PPC_TOC16.
        * bfd-in2.h: Rebuilt.

Fri Feb  4 17:28:32 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * libbfd.c (bfd_zmalloc): Call bfd_xmalloc instead of malloc.
        (bfd_xmalloc, bfd_xmalloc_by_size_t): Functions deleted.
        * libbfd-in.h: Define them as macros calling xmalloc and declare
        xmalloc. 
        * libbfd.h: Rebuilt.

Thu Feb  3 16:49:35 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * ecofflink.c (bfd_ecoff_debug_externals): If a small undefined
        symbol has a value in the ECOFF symbol but not in the BFD symbol,
        keep the value in the ECOFF symbol.  This helps gas.

        * linker.c (_bfd_generic_link_output_symbols,
        _bfd_generic_link_write_global_symbol): Don't require that all
        references to a common symbol be themselves common symbols.

        * aoutx.h (aout_reloc_index_to_section): Handle N_UNDF.

Wed Feb  2 20:37:19 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * libbfd.c, bfd-in.h, hosts/alphaosf.h, hosts/sparc-ll.h, aoutf1.h,
        sparclynx.c, Makefile.in: Change HOST_64_BIT to BFD_HOST_64_BIT.
        * bfd-in2.h: Rebuilt.

Wed Feb  2 12:30:13 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * coffswap.h (coff_swap_reloc_out): If RS6000COFF_C, handle type
        and size correctly.
        (coff_swap_aux_in): If RS6000COFF_C, change x_csect.x_scnlen to
        x_csect.x_scnlen.l to match change in coff/internal.h.
        (coff_swap_aux_out): Likewise.

        * coff-mips.c (mips_ecoff_backend_data), coff-alpha.c
        (alpha_ecoff_backend_data): Change casts of aux_in and aux_out
        fields to match yesterday's changes.

        * coffcode.h (coff_write_relocs): If SELECT_RELOC is defined, pass
        in the internal_reloc itself, not the type.
        * coff-apollo.c, coff-h8300.c, coff-h8500.c, coff-i386.c,
        coff-m68k.c, coff-sh.c, coff-we32k.c, coff-z8k.c: Changed
        definition of SELECT_RELOC accordingly.

Tue Feb  1 12:05:44 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * coffcode.h (bfd_coff_backend_data): Added new arguments to
        _bfd_coff_swap_aux_in and _bfd_coff_swap_aux_out: aux index number
        and number of aux entries.
        (bfd_coff_swap_aux_in, bfd_coff_swap_aux_out): Changed
        accordingly.
        * libcoff.h: Rebuilt.
        * coffswap.h (coff_swap_aux_in, coff_swap_aux_out): Accept new
        arguments.  If RS6000COFF_C, only treat C_EXT and C_HIDEXT
        specially if this is the last aux entry.
        * coffgen.c (coff_write_symbol, coff_get_normalized_symtab): Pass
        new arguments to swap_aux functions.

Sun Jan 30 15:14:36 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        * gen-aout.c (main): Set DEFAULT_ARCH based on preprocessor macros
        (only testing for m68k and vax at the moment); do verify that the
        preprocessor didn't trash the arch name inside the string version.
        Don't print out "pagesize =" line that prevents output from
        compiling.  Derive BYTES_IN_WORD and ARCH values from sizeof
        results.
        * Makefile.in (aout-params.h): Pass gen-aout a dummy target name.
        (check, installcheck): Identify directory in "no testsuites"
        message.

Sun Jan 30 13:25:28 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aoutx.h (aout_link_write_symbols): Write out correct value for
        object file symbol.

Fri Jan 28 18:34:05 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        * hosts/vaxbsd.h (HOST_STACK_END_ADDR): Vax BSD doesn't define
        KERNBASE, so hard-code 0x80000000 instead.

Thu Jan 27 13:54:08 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * linker.c (generic_link_add_symbol_list): If symbol is common,
        set the BSF_OLD_COMMON flag.

Wed Jan 26 13:47:15 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * format.c (bfd_check_format_matches): Put the new entry in the
        correct element of matching_vector.

Tue Jan 25 11:43:28 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * som.c, som.h (bfd_som_set_section_attributes,
        bfd_som_set_subsection_attributes): Change parameters from char
        to int.  Following a prototype with an old-style function definition
        in the presence of widened parameters is a GCC-ism not supported
        by the HP compiler in ANSI mode.

Tue Jan 25 11:46:46 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * reloc.c (bfd_get_reloc_size): Size of type -2 is 4 bytes, not 2.

        * hp300hpux.c (MY(write_object_contents)): Write out the symbols
        before writing out the relocs, so that the right symbol indices
        are used.

        * archive.c (do_slurp_bsd_armap, bfd_slurp_bsd_armap_f2): Do not
        try to overlay the internal carsyms on the external symdefs.  That
        can not work if the size of a host pointer is larger than 4 bytes.

        * format.c (bfd_check_format_matches): Cast result of
        bfd_xmalloc_by_size_t.
        * opncls.c (_bfd_new_bfd): Avoid ANSI C prototype.

        * archive.c: Reindented to GNU standards.

Mon Jan 24 14:41:23 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * opncls.c (_bfd_new_bfd, _bfd_new_bfd_contained_in): Add
        "_bfd_" to function names.
        * archive.c (_bfd_create_empty_archive_element_shell),
        libbfd-in.h: Change callers.

        * libbfd.c (bfd_zmalloc): Renamed from zalloc.
        * libbfd.c (bfd_add_to_string_table),
        trad-core.c (trad_unix_core_file_p),
        targets.c (bfd_target_list),
        ptrace-core.c (ptrace_unix_core_file_p),
        opncls.c (new_bfd), libbfd-in.h,
        ieee.c (ieee_make_empty_symbol),
        elf32-hppa.c (hppa_elf_stub_branch_reloc),
        (hppa_elf_stub_reloc): Change callers.
        * libbfd.h: Regenerated.

        * archive.c (_bfd_look_for_bfd_in_cache): Add "_bfd_" to name.
        (_bfd_get_elt_at_filepos), 
        coff-rs6000.c (rs6000coff_get_elt_at_filepos), libbfd-in.h:
        Change callers.

        * format.c (bfd_check_format_matches), libbfd-in.h, targets.c,
        elfcode.h (elf_object_p): Rename target_vector to bfd_target_vector
        and default_vector to bfd_default_vector.
        * libbfd.h: Regenerated.

        * format.c (bfd_check_format_matches): New function.
        (bfd_check_format): Call it.
        (bfd_matching_formats): Function removed.
        * targets.c: Replace the vector added on Jan 21 with a count of
        entries in default_vector.
        * bfd-in2.h: Regenerated.

Mon Jan 24 12:38:54 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * coff-alpha.c (alpha_ecoff_object_p): New function.  Set size of
        .pdata section based on lnnoptr field, not section header.
        (alpha_relocate_section): Don't bother to check if r_symndx >= 0,
        since it is unsigned.
        (ecoffalpha_little_vec): Use alpha_ecoff_object_p rather than
        coff_object_p.
        * ecoff.c (ecoff_new_section_hook): Set alignment_power field of
        .pdata section to 3.
        (ecoff_compute_section_file_positions): Save the size of the
        .pdata section in the line_filepos field, and actually align the
        .pdata section to an alignment power of 4.
        (ecoff_compute_reloc_file_positions): Set output_has_begun after
        calling ecoff_compute_section_file_positions.
        (ecoff_write_object_contents): Set s_lnnoptr for the .pdata
        section from the line_filepos field.  Set vstamp for the optional
        header from the vstamp of the symbolic header.
        (ecoff_bfd_final_link): Set vstamp of the symbolic header to the
        vstamp used by the first object file in the link.

        * ecofflink.c (ecoff_align_debug): Align RFDs to debug_align.

        * linker.c (generic_link_check_achive_element): Set SEC_ALLOC flag
        for a created common section.
        (_bfd_generic_link_add_one_symbol): Likewise.

        * elfcode.h (swap_out_syms): Use elf_section_from_bfd_section to
        get the index of a common section, rather than always using
        SHN_COMMON (MIPS has multiple common sections).

        * elf32-hppa.c (hppa_elf_gen_reloc_type): Typo (== for =).

        * bfd/aoutx.h (aout_link_input_section_std,
        aout_link_input_section_ext): Pass additional arguments to
        reloc_overflow callback.
        * coff-alpha.c (alpha_ecoff_get_relocated_section_contents,
        alpha_relocat_section): Likewise.
        * coff-h8300.c (h8300_reloc16_extra_cases): Likewise.
        * coff-h8500.c (extra_case): Likewise.
        * coff-mips.c (mips_relocate_section): Likewise.
        * coff-z8k.c (extra_case): Likewise.
        * elf32-hppa.c (hppa_elf_stub_finish): Likewise.
        * reloc.c (bfd_generic_get_relocated_section_contents): Likewise.

        * bout.c (calljx_callback, callj_callback): Use get_value to get
        the symbol value and check for undefined symbols.
        (get_value): If the symbol is undefined, look it up in the linker
        hash table.
        (b_out_get_relocated_section_contents): For PCREL24 and PCREL13
        use get_value to get the symbol value and check for undefined
        symbols.
        * reloc16.c (bfd_coff_reloc16_get_value): If the symbol is
        undefined, look it up in the linker hash table.

        * aoutx.h (translate_symbol_table): The string index 0 has a
        special meaning for normal symbols, but not for dynamic symbols.

Sat Jan 22 12:26:01 1994  Stu Grossman  (grossman at cygnus.com)

        * sparclynx.c:  Setup appropriate macros to enable core file
        support.

Fri Jan 21 16:25:35 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * targets.c: Add a vector of matching format names.
        * format.c (bfd_matching_formats): New function to return it.
        (bfd_check_format): Set it.
        * bfd-in2.h: Regenerated.

        * bfd-in.h: Remove decls of bfd_ec type and error printing functions.
        Remove decl of type symclass; wasn't used.
        * bfd.c: Document error handling, including code fragments
        containing the error decls that were in bfd-in.h.
        Remove DEFUNs.
        * bfd-in2.h: Regenerated.

Fri Jan 21 14:11:16 1994  Sean Fagan  (sef@cygnus.com)

        * nlmcode.h, liblnm.h, nlm32-alpha.c nlm32-i386.c nlm32-sparc.c:
        The sparc (and possibly other?) NLM format requires a different
        way to write exports, so add a write_export field to the backend
        data (and set it to NULL for everything but the sparc).

Fri Jan 21 14:11:16 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * sunos.c (MY(read_dynamic_relocs)): Compare info->dynrel with NULL,
        not (struct external_nlist *) NULL.  info->dynrel is a PTR, not
        a struct external_nlist *.

Fri Jan 21 09:29:01 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * bfd.c: Remove error strings for errors removed below.
        * aoutx.h (translate_to_native_sym_flags), bfd-in.h (bfd_ec),
        oasys.c (oasys_write_sections): Rename
        bfd_error_nonrepresentable_section to nonrepresentable_section.
        None of the other bfd error names start with "bfd_error".
        Remove errors symbol_not_found and no_relocation_info, which seem
        to be unused.
        * bfd-in2.h: Regenerated.

Fri Jan 21 01:11:55 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * bfd.c (bfd_get_gp_size): Added support for ELF.

        * syms.c (BSF_DYNAMIC): New symbol flag.
        (bfd_print_symbol_vandf): Print it.
        * bfd-in2.h: Rebuilt.
        * libaout.h (struct aout_backend_data): New read_dynamic_symbols
        and read_dynamic_relocs fields.
        (struct aoutdata): New dynamic_info field.
        (obj_aout_dynamic_info): New accessor macro.
        * sunos.c (struct sunos_dynamic_info): New structure.
        (sunos_read_dynamic_info, MY(read_dynamic_symbols),
        MY(read_dynamic_relocs)): New functions to read dynamic symbols
        and relocs.
        * aoutx.h (NAME(aout,some_aout_object_p)): If the object is
        dynamically linked, set SEC_RELOC for both the .text and .data
        sections.
        (translate_from_native_sym_flags): Don't set BSF_LOCAL for an
        undefined symbol.
        (translate_symbol_table): New function, split out of
        slurp_symbol_table; set the BSF_DYNAMIC flag appropriately.
        (NAME(aout,slurp_symbol_table)): Read dynamic symbols, if any.
        (NAME(aout,slurp_reloc_table)): Read dynamic relocs, if any.
        (NAME(aout,get_reloc_upper_bound)): Include dynamic reloc count in
        return value.
        * aoutf1.h (NAME(aout,sunos4_write_object_contents)): Don't write
        out dynamic symbols or relocs against reloc symbols, since they
        are already in the .text section and we wouldn't know where to
        write them anyhow.
        (sunos4_aout_backend): Initialize read_dynamic_symbols and
        read_dynamic_relocs fields.
        * aout-target.h (MY(backend_data)): Initialize
        read_dynamic_symbols and read_dynamic_relocs fields.

Thu Jan 20 20:57:27 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        * hosts/alphaosf.h (uint64e_type, uint64_type, int64_type): Delete
        typedefs, since HOST_64_BIT will take care of defining them in
        bfd.h.

Wed Jan 19 17:28:59 1994  Ken Raeburn  (raeburn@cujo.cygnus.com)

        * config/alphaosf.mh (HDEFINES): Don't define HOST_64_BIT here;
        that's dealt with elsewhere.
        * hosts/alphaosf.h (sprintf_vma, fprintf_vma): New macros.
        (uint64_typeHIGH, uint64_typeLOW): Comment with HOST_64_BIT so
        they get copied to bfd.h.

        * reloc.c (enum bfd_reloc_code_real): Add some Alpha relocation
        types.  Reorganized some of the existing ones.
        * coff-alpha.c (alpha_howto_table): Construct 64-bit negative one
        values in case of compilation on a 32-bit machine.  Fix pcrel
        fields of some reloc types.
        (alpha_bfd_reloc_type_lookup): Handle more relocation types.

        * bfd-in.h (uint64_typeHIGH, uint64_typeLOW): Supply default
        definitions when not defined, regardless of whether uint64_type is
        a defined macro or not.
        (fprintf_vma, sprintf_vma): Define only if fprintf_vma is not
        already defined.

Wed Jan 19 00:02:54 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aoutx.h (translate_to_native_sym_flags): Set the type of a
        BSF_WARNING symbol to N_WARNING.

Tue Jan 18 16:43:19 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aoutx.h (aout_link_add_symbols): Increment sym_hash as well as p
        for an indirect or warning symbol.
        (aout_link_write_symbols): Update sym_hash with the target of an
        indirect or warning symbol.  If an indirect symbol is defined,
        output the calculated value and don't output the target symbol.

Tue Jan 18 03:54:59 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * aoutx.h (translate_from_native_sym_flags): Give warning symbols
        an (unused) nonzero section value, needed for check below.

Mon Jan 17 15:12:07 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * aoutx.h (translate_from_native_sym_flags,
        aout_link_add_symbols): Treat N_SET[ABDT] | N_EXT like
        N_SET[ABDT].

Fri Jan 14 16:45:43 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elfcode.h (elf_object_p): If there is a SHT_DYNAMIC section, set
        the DYNAMIC flag for the BFD.
        (NAME(bfd_elf,write_object_contents)): Don't try to write out a
        BFD with the DYNAMIC flag set, since we don't generate the program
        header table correctly.

Fri Jan 14 01:04:36 1994  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        * elfcode.h (elf_slurp_symbol_table):  Free x_symp at the end
        of the function to avoid storage leak.

Thu Jan 13 23:07:32 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * ecoff.c (ecoff_link_write_external): An ifd can be -1.

Thu Jan 13 12:33:27 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_set_reloc_info): Provide a default symbol for
        relocations which don't actually have an associated symbol.

        * som.c (hppa_som_reloc): Add new "error message" argument.

Wed Jan 12 13:36:43 1994  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        Enable gdb to write to core files on more core file readers.
        * libbfd.c (bfd_generic_set_section_contents):  Remove range check
        for section size, it is already done in bfd_set_section_contents
        with bfd_get_section_size_now.
        * aix386-core.c, hppabsd-core.c, hpux-core.c, irix-core.c,
        osf-core.c, ptrace-core.c, trad-core.c (*_set_section_contents):
        Use bfd_generic_set_section_contents instead of bfd_false.

Wed Jan 12 15:31:57 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * linker.c: Added initial documentation.

        * linker.c (default_indirect_link_order): Don't expect space for
        output relocations if there aren't any input relocations.

Tue Jan 11 14:37:12 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * aoutx.h (NAME(aout,final_link)): Set a_entry before computing
        file offsets.

        * elfcode.h (swap_out_syms): A common symbol is STT_OBJECT, not
        STT_NOTYPE.

Tue Jan 11 09:10:56 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * config.bfd: Use ELF, not COFF for m88*-*-dgux*.
        Combine m88k-*-* and m88110-*-* cases into m88*-*-*.

Tue Jan 11 00:07:19 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * ecofflink.c: Extensive changes to compress and merge debugging
        information, and to write some of out directly rather than saving
        it in memory.  Several new functions and structures, and new
        arguments to existing functions.
        * ecoff.c (ecoff_compute_reloc_file_positions): Compute
        sym_filepos as well.
        (ecoff_get_extr): Use ifdmap instead of ifdbase.
        (ecoff_write_object_contents): Don't compute sym_filepos here.
        Only output symbols if outsymbols is not NULL.
        (ecoff_bfd_final_link): Adjust for changes in ecoff_debug_info and
        bfd_ecoff_debug functions.  Write out debugging information here.
        (ecoff_final_link_debug_accumulate): Adjust for changes in
        bfd_ecoff_debug functions.
        (ecoff_link_write_external): Use ifdmap rather than ifdbase.
        * elf32-mips.c (mips_elf_read_ecoff_info): Read external symbols
        first, to put them in the first memory buffer.  Clear fdr field.
        (mips_elf_get_extr): Use pointer to unswapped external symbol.
        (mips_elf_final_link): Adjust for changes in bfd_ecoff functions.
        Preserve .text, .data and .bss even if they are empty.  Save
        pointer to unswapped external symbol rather than copying it.
        Don't free up the external symbols.
        * libelf.h (elf_symbol_type): Change mips_extr to PTR.
        * bfd-in.h (bfd_ecoff_debug_init, bfd_ecoff_debug_free): Declare.
        (bfd_ecoff_debug_accumulate): Update declaration.
        (bfd_ecoff_debug_accumulate_other): Rename declaration from
        bfd_ecoff_debug_link_other and update.
        (bfd_ecoff_write_accumulated_debug): Declare.
        * bfd-in2.h: Rebuilt.
        * Makefile.in: Rebuilt dependencies.

Mon Jan 10 20:46:53 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * Makefile.in (install): Remove "@" which follows a backslash.  In
        this position it just causes errors, not suppresses echoes.

Mon Jan 10 09:06:21 1994  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (hppa_som_gen_reloc_type): Fix handling of LT and RT
        field selectors.

Sun Jan  9 04:32:25 1994  Ken Raeburn  (raeburn@kr-pc.cygnus.com)

        * config/i386-netbsd.mt (SELECT_VECS): Include i386bsd_vec.

Fri Jan  7 10:27:27 1994  David J. Mackenzie  (djm@rtl.cygnus.com)

        * aoutx.h (adjust_z_magic): Don't merge the start of bss with the
        end of data if they are not contiguous.

        * aoutf1.h (sunos4_aout_backend): Comment the fields' meanings.

Fri Jan  7 15:40:16 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * ecoff.c (ecoff_mkobject_hook): Don't set SEC_SHARED_LIBRARY flag
        for .reginfo section here.
        (ecoff_new_section_hook): Set it here instead.

Fri Jan  7 10:29:27 1994  Stan Shebs  (shebs@andros.cygnus.com)

        * bfd-in.h: (bfd_boolean): Add workaround for systems that also
        define true and false as enums.
        (ALMOST_STDC): Add as alternative to __STDC__.
        * bfd-in2.h: Rebuilt.
        * syms.c (bfd_print_symbol_vandf): Convert a PTR to FILE*.

Thu Jan  6 14:24:44 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * aoutx.h (translate_to_native_sym_flags): Catch the case where
        there is no output section.

Thu Jan  6 14:37:42 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * nlmcode.h (nlm_object_p): If we can't read the fixed header,
        count it as a wrong format error, not a system call error, since
        the object file might simply be too small.

        * targets.c (target_vector): Added nlm32_alpha_vec inside #ifdef
        BFD64.
        * Makefile.in (BFD32_BACKENDS): Remove nlm32-alpha.o.
        (BFD64_BACKENDS): Add nlm32-alpha.o.  It depends on 64 bit
        support, even though it is for an Alpha in 32 bit mode.
        * configure.in (nlm32_alpha_vec): Set target64 to true.

        * nlm32-gen.c, nlm64-gen.c: Removed.  All nlm targets are
        different, so there is no point to providing a generic one.
        * libnlm.h: Don't bother to check for nlm_backend(bfd) being NULL
        in the backend accessor macros; that should no longer be possible.
        * targets.c (target_vector): Removed nlm32_big_generic_vec,
        nlm64_big_generic_vec, nlm64_little_generic_vec.
        * configure.in (nlm32_big_generic_vec, nlm32_little_generic_vec,
        nlm64_big_generic_vec, nlm64_little_generic_vec): Removed.
        * Makefile.in: Rebuilt dependencies, and
        (BFD32_BACKENDS): Removed nlm32-gen.o.
        (BFD64_BACKENDS): Removed nlm64-gen.o.
        (CFILES): Removed nlm32-gen.c and nlm64-gen.c.

        * hp300hpux.c (ARCH_SIZE): Define before including aoutx.h.

        * linker.c (_bfd_generic_link_add_one_symbol): Add constructor and
        bitsize arguments.  Changed all callers (aoutx.h).
        * libbfd-in.h (_bfd_generic_link_add_one_symbol): Add constructor
        and bitsize arguments to declaration.
        * libbfd.h: Rebuilt.

        * ecoff.c: First cut at new style of linker backend for
        ECOFF--added a bunch of functions.  Also:
        (ecoff_sec_to_styp_flags): Set flags for .pdata and .xdata.
        (ecoff_slurp_symbolic_header): New function.
        (ecoff_slurp_symbolic_info): Call ecoff_slurp_symbolic_header.
        (ecoff_compute_reloc_file_positions): New function.
        (ecoff_set_section_contents): Get out quickly if count is zero.
        Check errors better.
        (ecoff_write_object_contents): Put .xdata section in data segment.
        Call ecoff_compute_reloc_file_positions.  Don't output relocs or
        external symbols if outsymbols is NULL.
        (ecoff_bfd_final_link): Completely rewritten.
        * libecoff.h: Include bfdlink.h.
        (struct ecoff_backend_data): Add relocate_section field.
        (ecoff_data_type): Add sym_hashes and symndx_to_section fields.
        (struct ecoff_link_hash_entry): Define.
        (struct ecoff_link_hash_table): Define.
        (ecoff_bfd_link_add_symbols): Declare as function, not macro.
        (ecoff_bfd_link_hash_table_create): Likewise.
        * ecofflink.c (bfd_ecoff_debug_one_external): New function.
        (bfd_ecoff_debug_externals): Call bfd_ecoff_debug_one_external.
        * bfd-in.h (bfd_ecoff_debug_one_external): Declare.
        * bfd-in2.h: Rebuilt.
        * coff-alpha.c (alpha_howto_table): Mark BRADDR as
        partial_inplace, and set the src_mask to 0x1fffff.
        (alpha_ecoff_get_relocated_section_contents): Remove unused
        variable gp_warned.
        (alpha_convert_external_reloc): New static function.
        (alpha_relocate_section): New static function.
        (alpha_ecoff_backend_data): Initialize relocate_section field.
        * coff-mips.c (mips_relocate_refhi): New static function.
        (mips_relocate_section): New static function.
        (mips_ecoff_backend_data): Initialize relocate_section field.

        * reloc.c (_bfd_relocate_contents): Corrected signed overflow
        checking when there is an addend.

        * aoutx.h (NAME(aout,final_link)): Don't abort when trying to link
        a non a.out file, just pass it to _bfd_default_link_order.
        (aout_link_input_section_std): When doing a final PC relative link
        against a section symbol, subtract the VMA of the input section.
        (aout_link_input_section_ext): Likewise.

        * linker.c (default_indirect_link_order): Renamed from
        _bfd_generic_indirect_link_order and made static.
        (_bfd_generic_final_link): Don't switch on link_order type, just
        call _bfd_default_link_order.
        (_bfd_default_link_order): Handle bfd_indirect_link_order type.
        * genlink.h: Removed declaration of
        _bfd_generic_indirect_link_order.
        * elf32-mips.c (mips_elf_final_link): Don't switch on link_order
        type, just call _bfd_default_link_order.

Tue Jan  4 21:23:37 1994  Ian Lance Taylor  (ian@cygnus.com)

        * linker.c (generic_link_check_archive_element): Base the name of
        the created common section on the name of the section the symbol
        came from.
        (_bfd_generic_link_add_one_symbol): (case BIG): A common symbol
        must have a section, so don't bother to create one.

Mon Jan  3 15:32:16 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * aout-target.h (MY(vec)): Add DYNAMIC to mask of object flags.
        * aoutf1.h (NAME(aout,sunos4_write_object_contents)):
        If the DYNAMIC flag is set, set it in the exec header.
        * aoutx.h (NAME(aout,some_aout_object_p)): If the object is
        dynamically linked, set the DYNAMIC flag in the BFD.
        * libaout.h (N_SET_DYNAMIC): New macro.
        (N_DYNAMIC): Add missing 0 in mask.

Mon Jan  3 11:41:45 1994  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * ecoff.c (ecoff_get_extr): Don't output section symbols as
        external symbols.

        * bfd-in.h, hash.c: Change bfd_hash_allocate argument from size_t
        to unsigned int, because size_t may not be defined in bfd.h.
        * bfd-in2.h: Rebuilt.

        * bfd-in.h (bfd_get{b,l}[_signed_]{16,32,64}): Declare argument to
        be a const pointer.
        * bfd-in2.h: Rebuilt.
        * libbfd.c (bfd_get{b,l}[_signed_]{16,32,64}): Declare argument to
        be a const pointer.
        * targets.c (bfd_target): Change swap function pointers
        accordingly.
        * archive.c (do_slurp_coff_armap): Change swap accordingly.
        * aix386-core.c: Change NO_GET and NO_GETS accordingly.
        * hppabsd-core.c, hpux-core.c, irix-core.c, osf-core.c,
        ptrace-core.c, trad-core.c: Change NO_GET and NO_SIGNED_GET
        accordingly.

        * libbfd-in.h (struct artdata): Added tdata field.
        (_bfd_add_bfd_to_archive_cache): Declare.
        (_bfd_get_elt_at_filepos): Declare.
        (_bfd_snarf_ar_hdr): Renamed from snarf_ar_hdr.
        * libbfd.h: Rebuilt.
        * archive.c: Cleaned up some more.
        (_bfd_generic_mkarchive, bfd_generic_archive_p): Initialize
        pointer elements of artdata.
        (_bfd_add_bfd_to_archive_cache): Renamed from add_bfd_to_cache.
        (_bfd_snarf_ar_hdr): Renamed from snarf_ar_hdr.
        (_bfd_get_elt_at_filepos): Renamed from get_elt_at_filepos.
        (get_extended_arelt_filename, bfd_construct_extended_name_table,
        bfd_ar_hdr_from_filesystem, compute_and_write_armap): Made static.
        * ecoff.c: Some comment changes.
        (ecoff_slurp_armap): Handle rename of snarf_ar_hdr.  Set
        ardata->tdata to raw_armap.
        (ecoff_archive_p): Initialize pointer elements of artdata.
        * coff-rs6000.c (rs6000coff_get_elt_at_filepos): Handle rename of
        add_bfd_to_cache.

        * hash.c: Added some documentation.

Mon Jan  3 11:09:28 1994  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * aout-target.h, netbsd386.c: Replace NO_SWAP_MAGIC with SWAP_MAGIC,
        and do the swapping here rather than calling ntohl from the N_*
        macros.  This cleans up assumptions about the size of a host long,
        the existence to ntohl, etc.

Sat Jan  1 13:50:05 1994  Rob Savoye  (rob@darkstar.cygnus.com)

        * config.bfd: Add support for VSTa micro-kernel. It currently uses
        i386-aout.

Sat Jan  1 10:18:54 1994  David J. Mackenzie  (djm@thepub.cygnus.com)

        * hosts/i386mach3.h (HOST_SEGMENT_SIZE): Fix value.
        * i386mach3.c (SEGMENT_SIZE): Fix value.

Fri Dec 31 16:23:43 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Minor cleanups suggested by CodeCenter.
        * aoutx.h, coffgen.c, ecoff.c, ecofflink.c, elf.c, libbfd.c,
        linker.c, reloc.c, section.c, srec.c: Added /*ARGSUSED*/ as
        appropriate.
        * aoutx.h (struct external_exec): Removed unnecessary declaration.
        (NAME(aout,some_aout_object_p)): Set some tdata pointers to NULL.
        (adjust_z_magic): Removed useless variable data_vma.
        (stringtab_init): Initialize hash_zero.
        (add_to_stringtab): Removed unused fourth argument.
        (NAME(aout,swap_std_reloc_out)): Removed useless variable
        r_addend.
        (aout_link_input_section): Added some casts.
        * archive.c (get_extended_arelt_filename, do_slurp_coff_armap,
        bfd_ar_hdr_from_filesystem, bsd_write_armap, coff_write_armap):
        Minor code rewriting to make it more C like.
        (do_slurp_bsd_armap): Added some casts.
        * ecoff.c (ecoff_write_object_contents): Removed useless variable
        scn_base.
        (ecoff_write_armap): Added some casts.  Use "" rather than "\0".
        * ecofflink.c (bfd_ecoff_write_debug): Added a cast.
        * libaout.h (struct internal_exec): Removed unnecessary
        declaration.
        * linker.c (_bfd_generic_indirect_link_order): Added a cast.
        * opncls.c (new_bfd): Removed a cast.
        * reloc.c (bfd_generic_get_relocated_section_contents): Added
        some casts.
        * srec.c (internal_srec_write_object_contents): Removed useless
        variable bytes_written.

Fri Dec 31 11:46:13 1993  David J. Mackenzie  (djm@thepub.cygnus.com)

        * i386mach3.c (N_TXTADDR): Don't define after all.
        (TEXT_START_ADDR): Don't include exec header size in value.

Thu Dec 30 15:47:54 1993  David J. Mackenzie  (djm@thepub.cygnus.com)

        * i386mach3.c (N_TXTADDR): Define.

Thu Dec 30 13:37:24 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        Extensive changes to move the bulk of the linker into BFD so that
        more efficient backend code can be written for specific object
        files.  Only existing efficient backend is a.out.
        * seclet.c, seclet.h: Removed.
        * hash.c, linker.c, genlink.h: New files.
        * bfd-in.h: Removed bfd_error_vector.  Declared hash table
        structures and functions.
        (JUMP_TABLE): Removed bfd_seclet_link, added
        bfd_link_hash_table_create, bfd_link_add_symbols and
        bfd_final_link.
        * All backends: Changed accordingly.
        * bfd-in2.h: Rebuilt.
        * bfd.c (struct _bfd): Added link_next and archive_pass fields.
        Removed ld_symbols field.
        (bfd_nonrepresentable_section, bfd_undefined_symbol,
        bfd_reloc_value_truncated, bfd_reloc_is_dangerous,
        bfd_error_vector): Removed.
        (bfd_default_error_trap, bfd_error_trap,
        bfd_error_nonrepresentabltrap): Removed.
        (bfd_get_relocated_section_contents): Pass link_info.  Pass
        link_order instead of seclet.  Pass symbols.
        (bfd_relax_section): Pass link_info.
        (bfd_seclet_link): Removed.
        (bfd_link_hash_table_create, bfd_link_add_symbols,
        bfd_final_link): New macros.
        * libbfd-in.h: If __GNUC__ is defined and alloca is not, define
        alloca as __builtin_alloca.  Declare internal linking functions.
        * libbfd.h: Rebuilt.
        * libbfd.c (bfd_seek): Comment out fseek assertion.  It's worked
        for months.
        * reloc.c (reloc_howto_type): Added error_message argument to
        special_function field.  Changed all callers and all definitions.
        (bfd_get_reloc_size): Make argument a const pointer.
        (bfd_perform_relocation): Add error_message argument to hold
        string set if return value if bfd_reloc_dangerous.  Changed all
        callers.
        (_bfd_final_link_relocate, _bfd_relocate_contents): New functions.
        * section.c (asection): Renamed seclets_head and seclets_tail to
        link_order_head and link_order_tail.
        * targets.c (bfd_target): Replaced seclet argument with link_info
        and link_order and symbols arguments in
        bfd_get_relocated_section_contents.  Added symbols argument to
        bfd_relax_section.  Removed bfd_seclet_link.  Added
        bfd_link_hash_table_create, bfd_link_add_symbols and
        bfd_final_link.
        * libaout.h (struct aoutdata): Added external_syms,
        external_sym_count, external_strings, sym_hashes fields.
        (obj_aout_external_syms, obj_aout_external_sym_count,
        obj_aout_external_strings, obj_aout_sym_hashes): New accessor
        macros.
        (WRITE_HEADERS): Only output symbols if outsymbols is not NULL.
        * aoutx.h: Wrote new back end linker routines.
        (translate_to_native_sym_flags): Return boolean value.  Don't use
        bfd_error_vector.
        (NAME(aout,write_syms)): Return boolean value.  Check return value
        of translate_to_native_sym_flags and bfd_write.
        * aout-target.h (final_link_callback): New function.
        (MY_bfd_final_link): New function.
        * aout-adobe.c (aout_adobe_write_object_contents): Check return
        value of aout_32_write_syms.
        * hp300hpux.c (MY(write_object_contents)): Likewise.
        * i386lynx.c (WRITE_HEADERS): Likewise.
        * libaout.h (WRITE_HEADERS): Likewise.
        * bout.c: Changed functions to use link_info->callbacks rather
        than bfd_error_vector, and link_orders rather than seclets.
        * coff-alpha.c: Likewise.
        * coff-h8300.c: Likewise.
        * coff-h8500.c: Likewise.
        * coff-sh.c: Likewise.
        * coff-z8k.c: Likewise.
        * elf32-hppa.c: Likewise.
        * reloc16.c: Likewise.
        * coff-alpha.c (alpha_ecoff_get_relocated_section_contents): Look
        up _gp in the hash table rather than in outsymbols.
        * coff-a29k.c (a29k_reloc): Pass errors back in new error_message
        argument rather than printing them.
        * coffcode.h (bfd_coff_reloc16_extra_cases): Take link_info and
        link_order arguments rather than seclet.  Changed all uses and
        definitions.
        (bfd_coff_reloc16_estimate): Pass link_info arguments.  Changed
        all uses and definitions.
        * libcoff.h: Rebuilt.
        * ecoff.c (ecoff_get_extr): If symbol is defined by linker, but
        not by ECOFF, make it scAbs.
        (ecoff_bfd_final_link): Renamed from ecoff_bfd_seclet_link and
        rewritten.
        * elf32-mips.c (mips_elf_final_link): Renamed from
        mips_elf_seclet_link and rewritten.
        * elf32-hppa.c (elf32_hppa_stub_description): Added link_info
        field.
        (new_stub, add_stub_by_name, hppa_elf_build_arg_reloc_stub,
        hppa_elf_build_long_branch_stub, hppa_look_for_stubs_in_section):
        Added link_info arguments.  Changed all callers.
        * elfcode.h (elf_slurp_symbol_table): Don't quit if outsymbols is
        not NULL.
        * oasys.c (oasys_write_sections): Return boolean value rather than
        using bfd_error_vector.
        (oasys_write_object_contents): Check return value of
        oasys_write_sections.
        * hosts/std-host.h: Don't declare qsort or strtol.
        * Makefile.in: Rebuild dependencies.
        (BFD_LIBS): Removed seclet.o.  Added hash.o and linker.o.
        (CFILES): Removed seclet.c.  Added hash.c and linker.c.
        (HFILES): Removed seclet.h.  Added genlink.h.

Thu Dec 30 07:41:36 1993  Peter Schauer  (pes@regent.e-technik.tu-muenchen.de)

        * section.c (bfd_get_section_contents):  Return zero filled buffer
        if section has no contents.

Tue Dec 28 12:43:54 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elf.c (bfd_elf_generic_reloc): If this is not an inplace reloc,
        then skip bfd_perform_relocation even if the addend is non-zero.

Tue Dec 21 09:22:19 1993  Ken Raeburn  (raeburn@rtl.cygnus.com)

        * coffcode.h (coff_write_relocs) [SWAP_OUT_RELOC_OFFSET]: Copy
        addend to r_offset field.

        * Makefile.in (CFILES): Added coff-sparc.c.  Rebuild dependencies.

        * coff-sparc.c (SWAP_IN_RELOC_OFFSET, SWAP_OUT_RELOC_OFFSET,
        CALC_ADDEND): Define.

        * aix386-core.c (aix386_core_file_p): Use cd_regs[0] for computing
        the offsetof because AIX /bin/cc does not like to take the address
        of an array.  (From Minh Tran-Le.)

Thu Dec 16 13:06:32 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * Thu Dec 16 15:41:06 1993  Peter Hoogenboom  (hoogen@cs.utah.edu)

        * elf32-hppa.c (hppa_elf_build_arg_reloc_stub): Make sure to copy
        the return pointer into %r2 if no jump-in-call-delay-slot
        optimization was done.

        * hosts/hp300bsd.h: Correctly identify 4.3BSD vs 4.4BSD.

Wed Dec 15 08:04:16 1993  David J. Mackenzie  (djm@thepub.cygnus.com)

        * hosts/std-host.h: (time): Don't declare; conflicts on Mach3.

        * hosts/i386mach3.h (HOST_PAGE_SIZE): Set to 1 to avoid padding.
        (HOST_SEGMENT_SIZE): Set to 0 for same reason.

        * i386mach3.c (PAGE_SIZE, SEGMENT_SIZE): Same changes as above.
        (TEXT_START_ADDR): Correct.
        (MY_backend_data): Define.

        * aoutx.h (adjust_o_magic, adjust_z_magic, adjust_n_magic):
        New functions; code moved from aout_<size>_adjust_sizes_and_vmas.

Tue Dec 14 21:48:33 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_begin_writing): Fix thinkos in auxiliary header
        support.
        (bfd_som_attach_aux_hdr): Likewise.

Mon Dec 13 23:34:48 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * elf32-hppa.c (hppa_elf_gen_reloc_type): Handle 'T' field
        selectors for PIC code.

        * som.c (hppa_som_gen_reloc_type): Handle 'T' field selectors.
        (som_write_fixups): Handle R_DLT_REL, R_FSEL, R_RSEL, R_LSEL
        relocations needed by PIC.

Tue Dec  7 15:47:51 1993  Stu Grossman  (grossman at cygnus.com)

        * nlmcode.h:  Fixes to avoid compiler warnings...

Tue Dec  7 15:10:54 1993  Ian Lance Taylor  (ian@cygnus.com)

        * libnlm.h (nlm_backend_data): Removed macro definition.
        (nlm_alpha_backend_data): Adjusted accordingly.

Sun Dec  5 19:32:08 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_begin_writing): Flesh out code for handling simple
        auxiliary headers.
        (bfd_som_attach_aux_hdr): New function.

        * som.h (struct somdata): Add fields for attaching version and
        copyright headers.  Add accessor macros.

        * som.c (R_DLT_REL, R_AUX_UNWIND, R_SEC_STMT): Add protected
        definitions for old versions of HPUX which fail to define them.
        (som_hppa_howto_talbe): Add R_DLT_REL, R_AUX_UNWIND, and R_SEC_STMT
        now that they're safe.  Delete bogus R_STATEMENT relocations.

        * som.c (som_hppa_howto_table): Add missing R_END_TRY.  Delete 
        extra R_DATA_OVERRIDE.
        (hppa_som_gen_reloc_type): Generate a relocation for the rounding
        mode selector if needed.
        (som_write_fixups): Handle requests for a change in the default
        rounding mode.  Rounding modes do not consume input bytes, but
        are just markers much like R_ENTRY and R_EXIT.

Sat Dec  4 19:40:32 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        Fri Dec  3 09:55:17 1993  Pete Hoogenboom  (hoogen@cs.utah.edu)

        * elf32-hppa.c: (hppa_elf_reloc):  Do not do code reordering when
        the branch instruction as originally been nullified.
        hppa_elf_reloc):  Avoid useless call to bfd_put_32 () in the
        case of no code reordering due to an LDO instruction in the
        delay slot of the branch.  Make sure to relocate the correct
        instruction.  Do not perform instruction reordering for millicode
        calls.
        (hppa_elf_build_arg_reloc_stub):  Change the relocation type
        to R_HPPA_STUB_CALL_17 when special processing might be needed.
        (hppa_elf_build_long_branch_stub): Prevent code reordering on
        a call from a linker stub to another linker stub and for millicode
        calls.  Do not trash the return register for calls from one linker
        stub to a second linker stub.

        * elf32-hppa.c: (elf_hppa_howto_table):  PLABEL and DLT
        relocations are not pc-relative.

        * hppa_stubs.h: (BLE_N_XXX_0_31):  New instruction used in
        linker stub code. 
        (COPY_2_31):  Likewise.

Fri Dec  3 18:40:58 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * config/solaris2.mh (HDEFINES): Remove -Dconst=
        * hosts/solaris.h: If not __GNUC__, define const as empty.

Thu Dec  2 15:43:32 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * ecoff.c: Added various casts for 32/64 bit cross targeting.
        (ecoff_mkobject_hook): Set SEC_SHARED_LIBRARY for the .reginfo
        section so that the linker ignores it.
        * ecofflink.c: Added various casts for 32/64 bit cross targeting.
        (ecoff_add_bytes): Changed need argument to size_t.
        (bfd_ecoff_debug_link_other): Check return value of
        ecoff_add_string.

        * libbfd-in.h (new_bfd): Use void rather than an empty parameter
        list.
        * libbfd.h: Rebuilt.

        * libnlm.h (struct nlm_obj_tdata): New field backend_data.
        (nlm_backend_data, nlm_alpha_backend_data): New accessor macros.
        (struct nlm_backend_data): New field no_uninitialized_data.
        (nlm_no_uninitialized_data): New accessor macro.
        * nlmcode.h (nlm_compute_section_file_positions): Handle
        no_uninitialized_data.
        (nlm_external_reloc_compare): Sort relocs by address for a
        particular symbol, to make the sort more stable.
        (nlm_write_object_contents): Cast the arguments to qsort.  Get the
        value of a debugging symbol the same way we get the value of a
        normal symbol.
        * nlm32-alpha.c: Various changes.  Write out GP and .lita relocs.
        Set no_uninitialized_data to true.
        * nlm32-i386.c (nlm32_i386_backend), nlm32-sparc.c
        (nlm32_sparc_backend): Set no_uninitialized_data field false.
        * nlmswap.h (nlm_swap_fixed_header_out): Zero out destination
        before filling it in.

Wed Dec  1 21:47:58 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_section_type, som_decode_symcalss): New functions.
        (som_get_symbol_info): Use them.
        (som_slurp_symbol_table): Set the section of common and undefined
        symbols correctly.

Wed Dec  1 14:15:10 1993  Ken Raeburn  (raeburn@cygnus.com)

        * elfcode.h (write_relocs): Initialize local var LAST_SYM_IDX, to
        make gcc happy.

        * mipsbsd.c: Changes from Ralph Campbell:
        (mips_howto_table_ext): MIPS_RELOC_LO16 should use
        complain_overflow_dont.
        (aout_mips_*_vec): Make name use "a.out" instead of "aout", to
        make gdb happy.

        * bfd.c (bfd_errmsgs): Reword invalid-target message.

        * config.bfd: For sparc*-*-coff, use sparc-coff.
        * configure.in: Handle sparccoff_vec.
        * targets.c (sparccoff_vec): Declare.

        * reloc.c (bfd_get_reloc_size): New function.
        (struct reloc_howto_type): Update documentation of size field.

Wed Dec  1 14:39:05 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * nlm32-alpha.c: New file; preliminary Alpha NetWare support.
        * config.bfd (alpha-*-netware*): New target; use alpha-nlm.
        * config/alpha-nlm.mt: New file.
        * configure.in (nlm32_alpha_vec): New vector; use nlm32-alpha.o,
        nlm32.o, and nlm.o.
        * Makefile.in (BFD32_BACKENDS): Added nlm32-alpha.o.
        (CFILES): Added nlm32-alpha.c.
        Rebuilt dependencies.
        * targets.c (nlm32_alpha_vec): Declare.

        * libnlm.h (struct nlm_backend_data): New fields
        optional_prefix_size, nlm_backend_object_p, nlm_write_prefix,
        nlm_set_public_section, nlm_get_public_offset.  Removed unused
        nlm_write_reloc field.  Changed nlm_write_import to remove
        unnecessary symbol argument.  Renamed nlm_write_externals to
        nlm_write_external, and changed cound argument from bfd_vma to
        bfd_size_type.
        (nlm_optional_prefix_size, nlm_backend_object_p_func,
        nlm_write_prefix_func, nlm_set_public_section_func,
        nlm_get_public_offset_func): New accessor macros.
        (nlm_write_reloc_func): Removed.
        (nlm_write_external_func): Adjusted for field renaming.
        * nlm32-i386.c (nlm_i386_write_import): Renamed from
        nlm_i386_write_reloc.  Removed old nlm_i386_write_import which
        just called old nlm_i386_write_reloc.
        (nlm_i386_write_external): Renamed from nlm_i386_write_externals.
        Declared.  Changed second argument from bfd_vma to bfd_size_type.
        (nlm32_i386_backend): Adjusted for changes to fields and names.
        * nlm32-sparc.c (nlm_sparc_mangle_relocs): Removed unused,
        ifdeffed out code.
        (nlm_sparc_write_import): Removed second argument.
        (nlm_sparc_write_external): Renamed from
        nlm_sparc_write_externals.  Changed second argument from bfd_vma
        to bfd_size_type.
        (nlm32_sparc_backend): Adjusted for changes to fields and names.
        * nlmcode.h: Removed some unused code.
        (nlm_object_p): Don't destroy tdata pointer.  Call
        backend_object_p function if it exists.
        (nlm_slurp_symbol_table): Removed unused variable rcount.  Call
        set_public_section_func if it exists instead of checking
        NLM_HIBIT.
        (nlm_compute_section_file_positions): Account for
        optional_prefix_size.
        (nlm_write_object_contents): Account for optional_prefix_size.
        Removed useless variable write_reloc_func.  Changed declaration
        and call of write_import_func.  Call write_prefix_func if it
        exists.  Removed unused variables len and temp.  Call
        get_public_offset_func if it exists rather than setting NLM_HIBIT.
        * nlmswap.h: Declare functions.

        * bfd-in.h (uint64_typeLOW, uint64_typeHIGH): Fully parenthesize
        for clarity.
        (fprintf_vma, sprintf_vma): Use %lx, not %x.
        * bfd-in2.h: Rebuilt.
        * hosts/alphaosf.h (uint64_typeLOW, uint64_typeHIGH): Cast results
        to unsigned long.

        * config.bfd: Don't set target64 here, as the setting is ignored.
        * configure.in (ecoffalpha_little_vec): Set target64.

        * config/alphaosf.mt (TDEFINES): Removed; setting host parameters
        in TDEFINES is wrong.

        * coff-alpha.c (alpha_ecoff_get_relocated_section_contents):
        Remove unused variable output_section.

Tue Nov 30 16:45:23 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * irix-core.c: New file for Irix 4 and Irix 5 core support.
        Functions taken out of coff-mips.c.  Handle vmap type VMAPFILE.
        * coff-mips.c: Irix 4 core file support moved to irix-core.c.
        * targets.c: If IRIX_CORE defined, include irix_core_vec in
        target_vector.
        * config/irix4.mh (HDEFINES): Add -DIRIX_CORE.
        (HDEPFILES): Define to be irix-core.o.
        * config/irix5.mh (HDEFINES): Define to be -DIRIX_CORE.
        (HDEPFILES): Define to be irix-core.o.
        * Makefile.in (OPTIONAL_BACKENDS): Added irix-core.o.  Removed
        sco-core.o, which no longer exists.
        (CFILES): Added all *-core.c files.
        Rebuilt dependencies.

Wed Nov 24 02:02:41 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elfcode.h (map_program_segments): Restore check of file_size !=
        mem_size, but only if SHT_PROGBITS.

        * ecofflink.c: New file to hold ECOFF debug information linking
        routines.
        * ecoff.c (ecoff_clear_output_flags, ecoff_rel, ecoff_dump_seclet,
        ecoff_add_string, ecoff_get_debug): Removed.  Functionality now in
        ecofflink.c.
        (ecoff_get_extr, ecoff_set_index): New functions.
        (ecoff_slurp_symbolic_info): Don't save raw_size.
        (ecoff_bfd_seclet_link): Rewrote to use ecofflink.c functions.
        (ecoff_compute_section_file_positions): Don't set EXEC_P just
        because there is a start address.
        (ecoff_write_object_contents): Handle external symbols here.  Use
        ecofflink.c functions to write out debugging information.
        * elf32-mips.c (mips_elf_read_ecoff_info, mips_elf_get_extr,
        mips_elf_set_index): New functions.
        (mips_elf_seclet_link): Discard empty sections, the .options
        section and .gptab sections.  Handle linking .mdebug section.
        * libecoff.h (ecoff_data_type): Removed raw_size and ifdbase.
        * libelf.h (elf_symbol_type): Added mips_extr to tc_data union.
        * bfd-in.h: Added prototypes for routines in ecofflink.c (some are
        called by gas, so they are public).
        * bfd-in2.h: Rebuilt.
        * Makefile.in (BFD_LIBS): Added ecofflink.o.
        (CFILES): Added ecofflink.c.
        (ecofflink.o): New target.  Rebuilt dependencies.

Mon Nov 22 22:26:42 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (hppa_object_p): Also recognize SHARED_MAGIC_CNX as
        a valid magic number if it's been defined.

Mon Nov 22 14:17:36 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * ecoff.c (ecoff_mkobject): Don't create .scommon section; linker
        no longer requires it.
        (ecoff_bfd_seclet_link, ecoff_sizeof_headers,
        ecoff_write_object_contents): Don't treat .scommon section
        specially.

Mon Nov 22 10:54:27 1993  Fred Fish  (fnf@cygnus.com)

        Merged changes from kev@spuds.geg.mot.com (Kevin A. Buettner):
        * bfd/config/delta88.mh (HDEFINES): Define this to be -DPTRACE_CORE.
        * bfd/config/delta88.mh (HDEPFILES): Defined to be ptrace-core.o.
        * bfd/ptrace-core.c:  New file for dealing with core files with
        start with the ptrace_user structure found on BCS compliant systems.
        * bfd/targets.c (ptrace_core_vec):  New vector.

Mon Nov 22 02:33:12 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * Minimal support for reading SOM fixup streams.  Allows
        objdump -r to do something reasonable.
        * som.c (som_get_reloc_upper_bound): Implement.
        (som_canonicalize_reloc): Implement.
        (som_set_reloc_info, som_slurp_reloc_table): New functions.

Sun Nov 21 13:46:55 1993  Ken Raeburn  (raeburn@cambridge.cygnus.com)

        * hosts/lynx.h (FPRINTF_ALREADY_DECLARED): Define.
        * hosts/sparclynx.h: Include lynx.h instead of duplicating it.

Fri Nov 19 14:34:04 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * coff-a29k.c (a29k_reloc): For R_IREL, don't left shift
        signed_value before sign extending it.  Don't subtract out
        reloc_entry->address.  This makes it compatible with what gas is
        generating.

        * elfcode.h (elf_fake_sections): Accept .sbss as the name for a
        SHT_NOBITS sections.
        (map_program_segments): Don't leave the loop after the first
        SHT_NOBITS section.
        (assign_file_positions_except_relocs): Only force sh_offset and
        sh_addr to match modulo maxpagesize for a section which is not
        SHT_NOBITS.  Changed the method used to force page alignment after
        a SHT_NOBITS section to only do it for the last such consecutive
        section, and to really force page alignment.

Fri Nov 19 04:02:01 1993  Ken Raeburn  (raeburn@cambridge.cygnus.com)

        * coffcode.h (coff_slurp_symbol_table): Print more verbose message
        in the case of an unknown (or unhandled) storage class.

        * config/i386-lynx.mt (TDEFINES): FPRINTF_ALREADY_DECLARED should
        not be defined here, since it is a host attribute, not a target
        one.
        * config/m68k-lynx.mt, config/sparc-lynx.mt: Ditto.

        * coffcode.h (coff_bfd_reloc_type_lookup): Don't define if already
        defined.

        * coff-sparc.c: Define some relocations, based on ELF relocations.
        (enum reloc_type, bfd_coff_generic_reloc, coff_sparc_howto_table,
        struct coff_reloc_map, sparc_reloc_map,
        coff_sparc_reloc_type_lookup): Borrowed from elf32-sparc.c and
        elf.c, renamed.
        (coff_bfd_reloc_type_lookup): Define to be coff_sparc_reloc_....
        (rtype2howto): Index into coff_sparc_howto_table using
        dst->r_type.

Thu Nov 18 11:45:39 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * config.bfd (mips*-*-irix5*): New target; use mipsbelf.
        * configure.host (mips-sgi-irix5*) New host; use irix5 (no
        hosts/irix5.h created; just use std-host.h).
        * config/irix5.mh: New file; like irix4.mh, but don't use -G or
        -lmalloc.
        * Makefile.in: Rebuilt dependencies.

        * ecoffswap.h: Changed type of internal pointers for swap out
        functions to const *.

        * elf32-mips.c (mips_elf_got16_reloc): New function.  Handle GOT16
        correctly for assembler, but linker support not implemented.
        (elf_mips_howto_table): Use mips_elf_got16_reloc for GOT16.
        (mips_elf_sym_is_global): New function; at least on Irix 5, all
        non section symbols are considered global.
        (elf_backend_sym_is_global): Define.
        (mips_elf_final_write_processing): New function.  Set the MIPS
        architecture level correctly.
        (elf_backend_final_write_processing): Define.
        (mips_elf_section_from_shdr): Handle SHT_MIPS_OPTIONS.
        (mips_elf_fake_sections): Set entsize of .mdebug or .reginfo
        section to 1.  Handle .options section.
        (mips_elf_acom_section, mips_elf_acom_symbol,
        mips_elf_acom_symbol_ptr): New static variables, used to build a
        generic .acommon section to hold SHN_MIPS_ACOMMON symbols.
        (mips_elf_symbol_processing): Handle SHN_MIPS_ACOMMON symbols by
        putting them all in a global .acommon section.

        * elfcode.h (bfd_section_from_shdr): Don't dump core if target
        section has no ELF section data.
        (elf_make_sections): Set addralign of reloc section to 4.
        (elf_fake_sections): Likewise.
        (map_program_segments): Don't consider section 0.
        (assign_file_positions_except_relocs): Don't consider section 0.
        In the main loop, skip the symtab and strtab sections, since their
        positions are set elsewhere.
        (swap_out_syms): Set addralign of symtab section to 4.  Set
        addralign of strtab sections to 1.
        (assign_file_positions_for_relocs): Don't consider section 0.
        (write_object_contents): Don't write out section 0.

        * libelf.h (struct elf_backend_data): Added fields
        elf_backend_sym_is_global and elf_backend_final_write_processing.
        * elf32-target.h (elf32_bed): Added corresponding initializers.
        * elf64-target.h (elf64_bed): Likewise.
        * elfcode.h (sym_is_global): Take abfd argument.  Call
        elf_backend_sym_is_global if it is not NULL.
        (elf_map_symbols): Pass abfd to sym_is_global.
        (write_object_contents): Call elf_backend_final_write_processing
        if it is defined.

Wed Nov 17 18:43:28 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * libecoff.h: Include coff/ecoff.h.
        (struct ecoff_backend_data): Move external debugging information
        fields into a single field pointing to an ecoff_debug_swap
        structure.
        (ecoff_data_type): Move debugging information fields into a single
        field pointing to an ecoff_debug_info structure.
        * coff-alpha.c, coff-mips.c, ecoff.c: Corresponding changes.

Wed Nov 17 17:38:58 1993  Sean Eric Fagan  (sef@cygnus.com)

        * nlmswap.h: New file to swap fixed header.  Included by NLM
        backends.
        * libnlm.h (struct reloc_and_sec): Define.
        (struct nlm_backend_data): Add fields fixed_header_size,
        nlm_read_import, nlm_write_import, nlm_swap_fhdr_in,
        nlm_swap_fhdr_out.
        (nlm_fixed_header_size, nlm_read_import_func,
        nlm_write_import_func, nlm_swap_fixed_header_in_func,
        nlm_swap_fixed_header_out_func, nlm_write_external_func): New
        accessor macros.
        * nlmcode.h: Use new functions.
        * nlm32-i386.c: Provide new functions.
        * nlm32-sparc.c: New file; SPARC NLM backend.

Wed Nov 17 13:56:10 1993  Stan Shebs  (shebs@rtl.cygnus.com)

        * i386lynx.c (swap_std_reloc_in, swap_ext_reloc_in): Ignore
        garbage bits appearing in the upper end of symbolnums.

        * config/sparc-lynx.mt (TDEFINES): Add -DFPRINTF_ALREADY_DECLARED.

Tue Nov 16 17:03:41 1993  Stu Grossman  (grossman at cygnus.com)

        * lynx-core.c (lynx_core_file_p):  Change bfd_zalloc to bfd_alloc.
        * m68klynx.c:  Define core file macros.
        * hosts/i386lynx.h, hosts/m68klynx.h, hosts/lynx.h:  Move all
        non-architecture specific stuff into lynx.h.

Tue Nov 16 15:45:54 1993  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * i386linux.c: Define new macro ZMAGIC_DISK_BLOCK_SIZE to 1024, and
        change PAGE_SIZE to 4096.

Mon Nov 15 11:48:08 1993  Ken Raeburn  (raeburn@rtl.cygnus.com)

        * Makefile.in (diststuff): New target.

        * VERSION: Updated.

Sun Nov 14 23:33:01 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_object_setup): Do not create dummy ".text", ".data",
        and ".bss" sections.
        (setup_sections): Do not set SEC_HAS_CONTENTS if a section's size
        is zero.  Recognize BSS type sections and turn off SEC_LOAD and
        SEC_DATA (so binutils/size works).  Set the correct value for
        a section's _raw_size.
        (som_slurp_symbol_table): Program entry points, and millicode are
        also functions.  Mark them as such.  Also mark L$* symbols as
        debugging symbols.

        * bfd-in2.h: Rebuilt.

Sat Nov 13 15:27:15 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_bfd_reloc_type_lookup): Add missing prototype.  Returns
        a pointer to constant data.  Delete bogus #define which made the 
        function useless.

        * som.c (som_prep_for_fixups): New function.
        (som_write_fixups): New function.
        (som_write_space_strings): New function.
        (som_write_symbol_strings): New function.
        (som_begin_writing): New function.

Fri Nov 12 15:29:36 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * som.c (som_write_object_contents): Do not abort.  Flesh out.
        (som_set_section_contents): Do not abort.  Flesh out.

        * som.c (som_write_headers): New function.
        (som_prep_headers): New function.
        (som_build_and_write_symbol_table): New function.

        * som.c (som_sizeof_headers): Add missing prototype.
        (som_set_arch_mach): Do not abort.

        * som.c (som_count_spaces): New function.
        (som_count_subspaces): New function.
        (compare_syms): New function.
        (som_compute_checksum): New function.

        * som.c (hppa_som_gen_reloc_type): New function.
        (som_bfd_reloc_type_lookup): New function.

        * som.c (try_prev_fixup): New function.
        (som_reloc_skip): New function.
        (som_reloc_addend): New function.
        (som_reloc_call): New function.

        * som.c (som_initialize_reloc_queue): New function.
        (som_reloc_queue_insert): Likewise.
        (som_reloc_queue_fix): Likewise.
        (som_reloc_queue_find): Likewise.

        * som.c (som_hppa_howto_table): SOM howto relocation table.
        (hppa_som_reloc): New function.

        * som.c (struct reloc_queue): New structure to keep track of
        the last four multibyte relocations emitted.
        (enum pa_symbol_type): Type to fully describe the symbol types
        associated with .import/.export assembler directives.

        * som.c: Include libhppa.h

        * som.c (bfd_som_set_section_attributes): New function.
        (bfd_som_set_subsection_attributes): Likewise.
        (bfd_som_set_symboL_type): Likewise.
        (bfd_som_attach_unwind_info): Likewise.
        * som.h: Declare new exported functions.

        * som.h (struct som_symbol): Add new fields to hold additional
        information needed to build/write symbol tables and fixup streams.
        (struct som_section_data_struct): Add new fields to hold additional
        information needed to build/write space and subspace headers.
        (som_symbol_data): New accessor macro for SOM symbol information.
        (R_HPPA_*): Basic relocation types to be used by the assembler.

Fri Nov 12 11:00:28 1993  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * trad-core.c (trad_unix_core_file_p): If new hook
        TRAD_CORE_ALLOW_ANY_EXTRA_SIZE defined, then skip the check for the
        corefile being too big.
        * hosts/i386sco.h: Define it.

Thu Nov 11 15:16:28 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * bfd.c (struct _bfd): Add hppabsd_core_data.
        * targets.c (target_vector): Add hppabsd_core_vec.
        * hpux-core.c (hpux_core_core_file_p): Fail if an unknown core
        section is encountered during core section scanning.
        * hppabsd-core.c: New file.
        * config/hppabsd.mh: Enable HPPA BSD core files.

        * elf32-hppa.c (hppa_elf_reloc): Remove DEFUN crud.  Remove code
        which is either commented out or ifdef'd out.  Add, update and
        clean comments.  Fix various indention and spacing problems.  Handle
        problems related to using "ble" to jump to a stub rather than "bl"
        (%r31 is trashed by "ble", but not by "bl").
        (NEW_INSTRUCTION): Put inside curly braces.
        (CURRENT_STUB_OFFSET): Fix indention problems.
        (hppa_elf_build_arg_reloc_stub): Fix indention and spacing problems.
        Add, update and clean comments.  Handle "ble" %r31 lossage problems.
        (hppa_elf_build_long_branch_stub): Likewise.
        (hppa_look_for_stubs_in_section): Likewise.
        (hppa_elf_stub_check): Remove obsolete function.

        * hppa_stubs.h: Add new instructions to deal with %r31 lossage
        problems.  Delete unused instructions.
        
Tue Nov  9 11:40:27 1993  Stan Shebs  (shebs@rtl.cygnus.com)

        * m68klynx.c (TARGET_IS_BIG_ENDIAN_P): Define.

Tue Nov  9 11:26:05 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elfcode.h (elf_object_p): Rather than looking through an array
        of architectures, get the ELF EM_xxx code from the backend
        information.  Let the generic ELF target match any EM_xxx code not
        matched by another ELF target.  Call elf_backend_object_p to let
        the backend do more checks and set global information.
        * libelf.h (struct elf_backend_data): Added elf_machine_code and
        elf_backend_object_p fields.
        (struct bfd_elf_arch_map): Removed.
        (bfd_elf_arch_map, bfd_elf_arch_map_size): Don't declare.
        * elf32-target.h, elf64-target.h: Initialize elf_machine_code
        field with ELF_MACHINE_CODE.  Initialize elf_backend_object_p
        field with elf_backend_object_p (if it is defined).
        * elf32-gen.c, elf32-hppa.c, elf32-i386.c, elf32-i860.c,
        elf32-m68k.c, elf32-m88k.c, elf32-mips.c, elf32-sparc.c,
        elf64-gen.c (ELF_MACHINE_CODE): Defined.
        * elf32-mips.c: Include ecoffswap.h to get ECOFF swapping
        routines.
        (mips_elf_object_p): Set the right machine number.
        (mips_elf_ecoff_debug_swap): Defined.
        (elf_backend_object_p): Defined to be mips_elf_object_p.
        (elf_backend_ecoff_debug_swap): Defined to be
        mips_elf_ecoff_debug_swap.
        * elf.c (bfd_elf_arch_map, bfd_elf_arch_map_size): Removed.

        * libbfd-in.h (target_vector, default_vector): Declare.
        * libbfd.h: Rebuilt.
        * format.c (target_vector, default_vector): Don't declare.

        * elf32-mips.c (elf_mips_howto_table): Don't complain on overflow
        for R_MIPS_26.  Correct overflow detection requires matching the
        upper four bits of the destination against the PC.  From Ted Lemon
        <mellon@pepper.ncd.com>.

        * bout.c (b_out_reloc_type_lookup): Return type should point to
        const data.
        * coff-i960.c (coff_i960_reloc_type_lookup): Likewise.
        * elf32-hppa.c (elf_hppa_reloc_type_lookup): Likewise.
        * mipsbsd.c (MY(reloc_howto_type_lookup)): Likewise.
        * coff-i386.c (coff_i386_reloc): Made howto const.
        * oasys.c (oasys_write_data): Made how const.

        * libelf.h: Added some comments.
        (struct elf_backend_data): Added elf_backend_ecoff_debug_swap
        field.  Removed unused write_relocs field.
        * elf32-target.h: Adjusted elf_backend_data initialization
        accordingly.
        * elf64-target.h: Corrected elf_backend_data initialization to
        fill in all fields and to set elf_64_p to 1.

Mon Nov  8 18:13:14 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elfcode.h (bfd_section_from_shdr): Remove duplicate assignment
        to filepos in SHT_STRTAB case.
        (assign_file_position_for_section): Set BFD section filepos as
        well as ELF section sh_offset.

        * reloc.c: Use const instead of CONST.
        (bfd_perform_relocation): Make variable howto a const pointer.
        * bfd-in2.h, libbfd.h: Rebuilt.

Mon Nov  8 12:19:15 1993  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * Makefile.in (realclean): Don't remove generated headers.  Reverts
        change of 2 Jul 1993.

Mon Nov  8 06:08:31 1993  D. V. Henkel-Wallace  (gumby@cirdan.cygnus.com)

        * configure.bfd: make unixware equivalent to sysv4.

        * config/i386-nlm.mt: bring in elf config; make it the default.

Sun Nov  7 20:21:38 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * libbfd.c (bfd_put_8): Add parens around reference to "val"
        argument.

Fri Nov  5 21:45:09 1993  David J. Mackenzie  (djm@thepub.cygnus.com)

        * hosts/i386mach3.h (HOST_SEGMENT_SIZE),
        i386mach3.c (SEGMENT_SIZE, TEXT_START_ADDR): Correct values (?).

Fri Nov  5 15:17:57 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * coffcode.h (coff_write_object_contents): Zero out internal_a.

Fri Nov  5 10:41:07 1993  David J. Mackenzie  (djm@thepub.cygnus.com)

        * aoutx.h, archive.c, archures.c, bfd.c, cache.c, coffcode.h,
        core.c, ctor.c, format.c, init.c, libbfd.c, opncls.c, reloc.c,
        section.c, syms.c, targets.c:
        Doc cleanup (spelling, punctuation, grammar, formatting).
        * bfd-in2.h, libbfd.h: Rebuild.

Thu Nov  4 14:46:14 1993  John Gilmore  (gnu@rtl.cygnus.com)

        * bfd-in.h (bfd_get_cacheable, bfd_set_cacheable):  New accessors.
        * bfd.c, opncls.c:  Improve comments on file descriptor cacheing.

Thu Nov  4 08:54:30 1993  Jeffrey A. Law  (law@snake.cs.utah.edu)

        * From Pete Hoogenboom (hoogen@cs.utah.edu)
        * elf32-hppa.c (hppa_elf_get_section_contents): Fix logic error
        in last change.  Always rebuild symbol extension section the first
        time though if output sections exist (fixes ld -r problems).

Thu Nov 04 08:08:46 1993  Jeffrey Wheat  (cassidy@cygnus.com)

        * Makefile.in: Add .PHONY for check and installcheck rules.

Tue Nov  2 14:42:27 1993  Bill Cox (bill@tarkas.cygnus.com)

        * libbfd-in.h (artdata): Use long, not time_t for portability, at
          least to HPUX.  File below is a derived file.

Tue Nov  2 14:42:27 1993  Bill Cox (bill@tarkas.cygnus.com)

        * libbfd.h (artdata): Use long, not time_t for portability, at
          least to HPUX.

Tue Nov  2 09:32:25 1993  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * config.bfd: Use bigmips for mips*-*-bsd*.

Mon Nov  1 14:30:09 1993  Ian Lance Taylor  (ian@tweedledumb.cygnus.com)

        * elfcode.h (elf_slurp_reloca_table, elf_slurp_reloc_table):
        Handle symbol number of zero.

        * reloc.c (enum bfd_reloc_code_real): Added
        BFD_RELOC_MIPS_LITERAL, BFD_RELOC_MIPS_GOT16,
        BFD_RELOC_MIPS_CALL16, BFD_RELOC_MIPS_GPREL32.
        * bfd-in2.h: Rebuilt.
        * coff-mips.c (mips_bfd_reloc_type_lookup): Handle
        BFD_RELOC_MIPS_LITERAL.
        * elf32-mips.c (mips_reloc_map): Handle new relocs.
        (mips_elf_hi16_reloc, mips_elf_lo16_reloc): Rearrange _gp_disp
        checks slightly.

        * aout-target.h (MY_bfd_debug_info_start, MY_bfd_debug_info_end,
        MY_bfd_debug_info_accumulat [sic]): Remove unused definitions.
        (MY_bfd_get_relocated_section_contents, MY_bfd_relax_section,
        MY_bfd_seclet_link): Define.
        (MY_bfd_reloc_type_lookup): Rename from
        MY_reloc_howto_type_lookup.
        (MY_bfd_make_debug_symbol): Rename from MY_make_debug_symbol.
        (MY(vec)): Use JUMP_TABLE rather than listing functions.
        * hp300hpux.c (MY_get_symtab, MY_get_symtab_upper_bound,
        MY_canonicalize_reloc, MY_write_object_contents): Don't define in
        terms of MY, because that causes a recusive invocation of CAT when
        expanded within JUMP_TABLE, and ANSI compilers don't expand
        recursive macros.
        * mipsbsd.c (MY_bfd_reloc_type_lookup): Rename from
        MY_reloc_howto_type_lookup, and don't define in terms of MY.
        (MY_canonicalize_reloc): Don't define in terms of MY.
        (aout_mips_little_vec, aout_mips_big_vec): Use JUMP_TABLE rather
        than listing functions.

Mon Nov  1 09:12:25 1993  Jim Kingdon  (kingdon@lioth.cygnus.com)

        * config.bfd: Use m68k-elf for m68*-*-sysv4*.

See file ChangeLog.1

\f
Local Variables:
mode: indented-text
left-margin: 8
fill-column: 74
version-control: never
End: