drivers/ata/Kconfig

   1 #
   2 # SATA/PATA driver configuration
   3 #
   4
   5 menuconfig ATA
   6         tristate "Serial ATA and Parallel ATA drivers"
   7         depends on HAS_IOMEM
   8         depends on BLOCK
   9         depends on !(M32R || M68K) || BROKEN
  10         select SCSI
  11         ---help---
  12           If you want to use a ATA hard disk, ATA tape drive, ATA CD-ROM or
  13           any other ATA device under Linux, say Y and make sure that you know
  14           the name of your ATA host adapter (the card inside your computer
  15           that "speaks" the ATA protocol, also called ATA controller),
  16           because you will be asked for it.
  17
  18           NOTE: ATA enables basic SCSI support; *however*,
  19           'SCSI disk support', 'SCSI tape support', or
  20           'SCSI CDROM support' may also be needed,
  21           depending on your hardware configuration.
  22
  23 if ATA
  24
  25 config ATA_NONSTANDARD
  26        bool
  27        default n
  28
  29 config ATA_VERBOSE_ERROR
  30         bool "Verbose ATA error reporting"
  31         default y
  32         help
  33           This option adds parsing of ATA command descriptions and error bits
  34           in libata kernel output, making it easier to interpret.
  35           This option will enlarge the kernel by approx. 6KB. Disable it only
  36           if kernel size is more important than ease of debugging.
  37
  38           If unsure, say Y.
  39
  40 config ATA_ACPI
  41         bool "ATA ACPI Support"
  42         depends on ACPI && PCI
  43         select ACPI_DOCK
  44         default y
  45         help
  46           This option adds support for ATA-related ACPI objects.
  47           These ACPI objects add the ability to retrieve taskfiles
  48           from the ACPI BIOS and write them to the disk controller.
  49           These objects may be related to performance, security,
  50           power management, or other areas.
  51           You can disable this at kernel boot time by using the
  52           option libata.noacpi=1
  53
  54 config SATA_PMP
  55         bool "SATA Port Multiplier support"
  56         default y
  57         help
  58           This option adds support for SATA Port Multipliers
  59           (the SATA version of an ethernet hub, or SAS expander).
  60
  61 config SATA_AHCI
  62         tristate "AHCI SATA support"
  63         depends on PCI
  64         help
  65           This option enables support for AHCI Serial ATA.
  66
  67           If unsure, say N.
  68
  69 config SATA_SIL24
  70         tristate "Silicon Image 3124/3132 SATA support"
  71         depends on PCI
  72         help
  73           This option enables support for Silicon Image 3124/3132 Serial ATA.
  74
  75           If unsure, say N.
  76
  77 config SATA_FSL
  78         tristate "Freescale 3.0Gbps SATA support"
  79         depends on FSL_SOC
  80         help
  81           This option enables support for Freescale 3.0Gbps SATA controller.
  82           It can be found on MPC837x and MPC8315.
  83
  84           If unsure, say N.
  85
  86 config ATA_SFF
  87         bool "ATA SFF support"
  88         default y
  89         help
  90           This option adds support for ATA controllers with SFF
  91           compliant or similar programming interface.
  92
  93           SFF is the legacy IDE interface that has been around since
  94           the dawn of time.  Almost all PATA controllers have an
  95           SFF interface.  Many SATA controllers have an SFF interface
  96           when configured into a legacy compatibility mode.
  97
  98           For users with exclusively modern controllers like AHCI,
  99           Silicon Image 3124, or Marvell 6440, you may choose to
 100           disable this unneeded SFF support.
 101
 102           If unsure, say Y.
 103
 104 if ATA_SFF
 105
 106 config SATA_SVW
 107         tristate "ServerWorks Frodo / Apple K2 SATA support"
 108         depends on PCI
 109         help
 110           This option enables support for Broadcom/Serverworks/Apple K2
 111           SATA support.
 112
 113           If unsure, say N.
 114
 115 config ATA_PIIX
 116         tristate "Intel ESB, ICH, PIIX3, PIIX4 PATA/SATA support"
 117         depends on PCI
 118         help
 119           This option enables support for ICH5/6/7/8 Serial ATA
 120           and support for PATA on the Intel ESB/ICH/PIIX3/PIIX4 series
 121           host controllers.
 122
 123           If unsure, say N.
 124
 125 config SATA_MV
 126         tristate "Marvell SATA support"
 127         help
 128           This option enables support for the Marvell Serial ATA family.
 129           Currently supports 88SX[56]0[48][01] PCI(-X) chips,
 130           as well as the newer [67]042 PCI-X/PCIe and SOC devices.
 131
 132           If unsure, say N.
 133
 134 config SATA_NV
 135         tristate "NVIDIA SATA support"
 136         depends on PCI
 137         help
 138           This option enables support for NVIDIA Serial ATA.
 139
 140           If unsure, say N.
 141
 142 config PDC_ADMA
 143         tristate "Pacific Digital ADMA support"
 144         depends on PCI
 145         help
 146           This option enables support for Pacific Digital ADMA controllers
 147
 148           If unsure, say N.
 149
 150 config SATA_QSTOR
 151         tristate "Pacific Digital SATA QStor support"
 152         depends on PCI
 153         help
 154           This option enables support for Pacific Digital Serial ATA QStor.
 155
 156           If unsure, say N.
 157
 158 config SATA_PROMISE
 159         tristate "Promise SATA TX2/TX4 support"
 160         depends on PCI
 161         help
 162           This option enables support for Promise Serial ATA TX2/TX4.
 163
 164           If unsure, say N.
 165
 166 config SATA_SX4
 167         tristate "Promise SATA SX4 support (Experimental)"
 168         depends on PCI && EXPERIMENTAL
 169         help
 170           This option enables support for Promise Serial ATA SX4.
 171
 172           If unsure, say N.
 173
 174 config SATA_SIL
 175         tristate "Silicon Image SATA support"
 176         depends on PCI
 177         help
 178           This option enables support for Silicon Image Serial ATA.
 179
 180           If unsure, say N.
 181
 182 config SATA_SIS
 183         tristate "SiS 964/965/966/180 SATA support"
 184         depends on PCI
 185         select PATA_SIS
 186         help
 187           This option enables support for SiS Serial ATA on
 188           SiS 964/965/966/180 and Parallel ATA on SiS 180.
 189           The PATA support for SiS 180 requires additionally to
 190           enable the PATA_SIS driver in the config.
 191           If unsure, say N.
 192
 193 config SATA_ULI
 194         tristate "ULi Electronics SATA support"
 195         depends on PCI
 196         help
 197           This option enables support for ULi Electronics SATA.
 198
 199           If unsure, say N.
 200
 201 config SATA_VIA
 202         tristate "VIA SATA support"
 203         depends on PCI
 204         help
 205           This option enables support for VIA Serial ATA.
 206
 207           If unsure, say N.
 208
 209 config SATA_VITESSE
 210         tristate "VITESSE VSC-7174 / INTEL 31244 SATA support"
 211         depends on PCI
 212         help
 213           This option enables support for Vitesse VSC7174 and Intel 31244 Serial ATA.
 214
 215           If unsure, say N.
 216
 217 config SATA_INIC162X
 218         tristate "Initio 162x SATA support"
 219         depends on PCI
 220         help
 221           This option enables support for Initio 162x Serial ATA.
 222
 223 config PATA_ACPI
 224         tristate "ACPI firmware driver for PATA"
 225         depends on ATA_ACPI
 226         help
 227           This option enables an ACPI method driver which drives
 228           motherboard PATA controller interfaces through the ACPI
 229           firmware in the BIOS. This driver can sometimes handle
 230           otherwise unsupported hardware.
 231
 232 config PATA_ALI
 233         tristate "ALi PATA support"
 234         depends on PCI
 235         help
 236           This option enables support for the ALi ATA interfaces
 237           found on the many ALi chipsets.
 238
 239           If unsure, say N.
 240
 241 config PATA_AMD
 242         tristate "AMD/NVidia PATA support"
 243         depends on PCI
 244         help
 245           This option enables support for the AMD and NVidia PATA
 246           interfaces found on the chipsets for Athlon/Athlon64.
 247
 248           If unsure, say N.
 249
 250 config PATA_ARTOP
 251         tristate "ARTOP 6210/6260 PATA support"
 252         depends on PCI
 253         help
 254           This option enables support for ARTOP PATA controllers.
 255
 256           If unsure, say N.
 257
 258 config PATA_ATP867X
 259         tristate "ARTOP/Acard ATP867X PATA support"
 260         depends on PCI
 261         help
 262           This option enables support for ARTOP/Acard ATP867X PATA
 263           controllers.
 264
 265           If unsure, say N.
 266
 267 config PATA_AT32
 268         tristate "Atmel AVR32 PATA support (Experimental)"
 269         depends on AVR32 && PLATFORM_AT32AP && EXPERIMENTAL
 270         help
 271           This option enables support for the IDE devices on the
 272           Atmel AT32AP platform.
 273
 274           If unsure, say N.
 275
 276 config PATA_ATIIXP
 277         tristate "ATI PATA support"
 278         depends on PCI
 279         help
 280           This option enables support for the ATI ATA interfaces
 281           found on the many ATI chipsets.
 282
 283           If unsure, say N.
 284
 285 config PATA_CMD640_PCI
 286         tristate "CMD640 PCI PATA support (Experimental)"
 287         depends on PCI && EXPERIMENTAL
 288         help
 289           This option enables support for the CMD640 PCI IDE
 290           interface chip. Only the primary channel is currently
 291           supported.
 292
 293           If unsure, say N.
 294
 295 config PATA_CMD64X
 296         tristate "CMD64x PATA support"
 297         depends on PCI
 298         help
 299           This option enables support for the CMD64x series chips
 300           except for the CMD640.
 301
 302           If unsure, say N.
 303
 304 config PATA_CS5520
 305         tristate "CS5510/5520 PATA support"
 306         depends on PCI
 307         help
 308           This option enables support for the Cyrix 5510/5520
 309           companion chip used with the MediaGX/Geode processor family.
 310
 311           If unsure, say N.
 312
 313 config PATA_CS5530
 314         tristate "CS5530 PATA support"
 315         depends on PCI
 316         help
 317           This option enables support for the Cyrix/NatSemi/AMD CS5530
 318           companion chip used with the MediaGX/Geode processor family.
 319
 320           If unsure, say N.
 321
 322 config PATA_CS5535
 323         tristate "CS5535 PATA support (Experimental)"
 324         depends on PCI && X86 && !X86_64 && EXPERIMENTAL
 325         help
 326           This option enables support for the NatSemi/AMD CS5535
 327           companion chip used with the Geode processor family.
 328
 329           If unsure, say N.
 330
 331 config PATA_CS5536
 332         tristate "CS5536 PATA support"
 333         depends on PCI && X86 && !X86_64
 334         help
 335           This option enables support for the AMD CS5536
 336           companion chip used with the Geode LX processor family.
 337
 338           If unsure, say N.
 339
 340 config PATA_CYPRESS
 341         tristate "Cypress CY82C693 PATA support (Very Experimental)"
 342         depends on PCI && EXPERIMENTAL
 343         help
 344           This option enables support for the Cypress/Contaq CY82C693
 345           chipset found in some Alpha systems
 346
 347           If unsure, say N.
 348
 349 config PATA_EFAR
 350         tristate "EFAR SLC90E66 support"
 351         depends on PCI
 352         help
 353           This option enables support for the EFAR SLC90E66
 354           IDE controller found on some older machines.
 355
 356           If unsure, say N.
 357
 358 config ATA_GENERIC
 359         tristate "Generic ATA support"
 360         depends on PCI
 361         help
 362           This option enables support for generic BIOS configured
 363           ATA controllers via the new ATA layer
 364
 365           If unsure, say N.
 366
 367 config PATA_HPT366
 368         tristate "HPT 366/368 PATA support"
 369         depends on PCI
 370         help
 371           This option enables support for the HPT 366 and 368
 372           PATA controllers via the new ATA layer.
 373
 374           If unsure, say N.
 375
 376 config PATA_HPT37X
 377         tristate "HPT 370/370A/371/372/374/302 PATA support"
 378         depends on PCI
 379         help
 380           This option enables support for the majority of the later HPT
 381           PATA controllers via the new ATA layer.
 382
 383           If unsure, say N.
 384
 385 config PATA_HPT3X2N
 386         tristate "HPT 372N/302N PATA support"
 387         depends on PCI
 388         help
 389           This option enables support for the N variant HPT PATA
 390           controllers via the new ATA layer
 391
 392           If unsure, say N.
 393
 394 config PATA_HPT3X3
 395         tristate "HPT 343/363 PATA support"
 396         depends on PCI
 397         help
 398           This option enables support for the HPT 343/363
 399           PATA controllers via the new ATA layer
 400
 401           If unsure, say N.
 402
 403 config PATA_HPT3X3_DMA
 404         bool "HPT 343/363 DMA support"
 405         depends on PATA_HPT3X3
 406         help
 407           This option enables DMA support for the HPT343/363
 408           controllers. Enable with care as there are still some
 409           problems with DMA on this chipset.
 410
 411 config PATA_ISAPNP
 412         tristate "ISA Plug and Play PATA support"
 413         depends on ISAPNP
 414         help
 415           This option enables support for ISA plug & play ATA
 416           controllers such as those found on old soundcards.
 417
 418           If unsure, say N.
 419
 420 config PATA_IT821X
 421         tristate "IT8211/2 PATA support"
 422         depends on PCI
 423         help
 424           This option enables support for the ITE 8211 and 8212
 425           PATA controllers via the new ATA layer, including RAID
 426           mode.
 427
 428           If unsure, say N.
 429
 430 config PATA_IT8213
 431         tristate "IT8213 PATA support (Experimental)"
 432         depends on PCI && EXPERIMENTAL
 433         help
 434           This option enables support for the ITE 821 PATA
 435           controllers via the new ATA layer.
 436
 437           If unsure, say N.
 438
 439 config PATA_JMICRON
 440         tristate "JMicron PATA support"
 441         depends on PCI
 442         help
 443           Enable support for the JMicron IDE controller, via the new
 444           ATA layer.
 445
 446           If unsure, say N.
 447
 448 config PATA_LEGACY
 449         tristate "Legacy ISA PATA support (Experimental)"
 450         depends on ISA && EXPERIMENTAL
 451         help
 452           This option enables support for ISA/VLB bus legacy PATA
 453           ports and allows them to be accessed via the new ATA layer.
 454
 455           If unsure, say N.
 456
 457 config PATA_TRIFLEX
 458         tristate "Compaq Triflex PATA support"
 459         depends on PCI
 460         help
 461           Enable support for the Compaq 'Triflex' IDE controller as found
 462           on many Compaq Pentium-Pro systems, via the new ATA layer.
 463
 464           If unsure, say N.
 465
 466 config PATA_MARVELL
 467         tristate "Marvell PATA support via legacy mode"
 468         depends on PCI
 469         help
 470           This option enables limited support for the Marvell 88SE61xx ATA
 471           controllers. If you wish to use only the SATA ports then select
 472           the AHCI driver alone. If you wish to the use the PATA port or
 473           both SATA and PATA include this driver.
 474
 475           If unsure, say N.
 476
 477 config PATA_MPC52xx
 478         tristate "Freescale MPC52xx SoC internal IDE"
 479         depends on PPC_MPC52xx && PPC_BESTCOMM
 480         select PPC_BESTCOMM_ATA
 481         help
 482           This option enables support for integrated IDE controller
 483           of the Freescale MPC52xx SoC.
 484
 485           If unsure, say N.
 486
 487 config PATA_MPIIX
 488         tristate "Intel PATA MPIIX support"
 489         depends on PCI
 490         help
 491           This option enables support for MPIIX PATA support.
 492
 493           If unsure, say N.
 494
 495 config PATA_OLDPIIX
 496         tristate "Intel PATA old PIIX support"
 497         depends on PCI
 498         help
 499           This option enables support for early PIIX PATA support.
 500
 501           If unsure, say N.
 502
 503 config PATA_NETCELL
 504         tristate "NETCELL Revolution RAID support"
 505         depends on PCI
 506         help
 507           This option enables support for the Netcell Revolution RAID
 508           PATA controller.
 509
 510           If unsure, say N.
 511
 512 config PATA_NINJA32
 513         tristate "Ninja32/Delkin Cardbus ATA support"
 514         depends on PCI
 515         help
 516           This option enables support for the Ninja32, Delkin and
 517           possibly other brands of Cardbus ATA adapter
 518
 519           If unsure, say N.
 520
 521 config PATA_NS87410
 522         tristate "Nat Semi NS87410 PATA support"
 523         depends on PCI
 524         help
 525           This option enables support for the National Semiconductor
 526           NS87410 PCI-IDE controller.
 527
 528           If unsure, say N.
 529
 530 config PATA_NS87415
 531         tristate "Nat Semi NS87415 PATA support"
 532         depends on PCI
 533         help
 534           This option enables support for the National Semiconductor
 535           NS87415 PCI-IDE controller.
 536
 537           If unsure, say N.
 538
 539 config PATA_OPTI
 540         tristate "OPTI621/6215 PATA support (Very Experimental)"
 541         depends on PCI && EXPERIMENTAL
 542         help
 543           This option enables full PIO support for the early Opti ATA
 544           controllers found on some old motherboards.
 545
 546           If unsure, say N.
 547
 548 config PATA_OPTIDMA
 549         tristate "OPTI FireStar PATA support (Very Experimental)"
 550         depends on PCI && EXPERIMENTAL
 551         help
 552           This option enables DMA/PIO support for the later OPTi
 553           controllers found on some old motherboards and in some
 554           laptops.
 555
 556           If unsure, say N.
 557
 558 config PATA_PALMLD
 559         tristate "Palm LifeDrive PATA support"
 560         depends on MACH_PALMLD
 561         help
 562           This option enables support for Palm LifeDrive's internal ATA
 563           port via the new ATA layer.
 564
 565           If unsure, say N.
 566
 567 config PATA_PCMCIA
 568         tristate "PCMCIA PATA support"
 569         depends on PCMCIA
 570         help
 571           This option enables support for PCMCIA ATA interfaces, including
 572           compact flash card adapters via the new ATA layer.
 573
 574           If unsure, say N.
 575
 576 config PATA_PDC2027X
 577         tristate "Promise PATA 2027x support"
 578         depends on PCI
 579         help
 580           This option enables support for Promise PATA pdc20268 to pdc20277 host adapters.
 581
 582           If unsure, say N.
 583
 584 config PATA_PDC_OLD
 585         tristate "Older Promise PATA controller support"
 586         depends on PCI
 587         help
 588           This option enables support for the Promise 20246, 20262, 20263,
 589           20265 and 20267 adapters.
 590
 591           If unsure, say N.
 592
 593 config PATA_QDI
 594         tristate "QDI VLB PATA support"
 595         depends on ISA
 596         help
 597           Support for QDI 6500 and 6580 PATA controllers on VESA local bus.
 598
 599 config PATA_RADISYS
 600         tristate "RADISYS 82600 PATA support (Experimental)"
 601         depends on PCI && EXPERIMENTAL
 602         help
 603           This option enables support for the RADISYS 82600
 604           PATA controllers via the new ATA layer
 605
 606           If unsure, say N.
 607
 608 config PATA_RB532
 609         tristate "RouterBoard 532 PATA CompactFlash support"
 610         depends on MIKROTIK_RB532
 611         help
 612           This option enables support for the RouterBoard 532
 613           PATA CompactFlash controller.
 614
 615           If unsure, say N.
 616
 617 config PATA_RDC
 618         tristate "RDC PATA support"
 619         depends on PCI
 620         help
 621           This option enables basic support for the later RDC PATA controllers
 622           controllers via the new ATA layer. For the RDC 1010, you need to
 623           enable the IT821X driver instead.
 624
 625           If unsure, say N.
 626
 627 config PATA_RZ1000
 628         tristate "PC Tech RZ1000 PATA support"
 629         depends on PCI
 630         help
 631           This option enables basic support for the PC Tech RZ1000/1
 632           PATA controllers via the new ATA layer
 633
 634           If unsure, say N.
 635
 636 config PATA_SC1200
 637         tristate "SC1200 PATA support"
 638         depends on PCI
 639         help
 640           This option enables support for the NatSemi/AMD SC1200 SoC
 641           companion chip used with the Geode processor family.
 642
 643           If unsure, say N.
 644
 645 config PATA_SERVERWORKS
 646         tristate "SERVERWORKS OSB4/CSB5/CSB6/HT1000 PATA support"
 647         depends on PCI
 648         help
 649           This option enables support for the Serverworks OSB4/CSB5/CSB6 and
 650           HT1000 PATA controllers, via the new ATA layer.
 651
 652           If unsure, say N.
 653
 654 config PATA_SIL680
 655         tristate "CMD / Silicon Image 680 PATA support"
 656         depends on PCI
 657         help
 658           This option enables support for CMD / Silicon Image 680 PATA.
 659
 660           If unsure, say N.
 661
 662 config PATA_SIS
 663         tristate "SiS PATA support"
 664         depends on PCI
 665         help
 666           This option enables support for SiS PATA controllers
 667
 668           If unsure, say N.
 669
 670 config PATA_TOSHIBA
 671         tristate "Toshiba Piccolo support (Experimental)"
 672         depends on PCI && EXPERIMENTAL
 673         help
 674           Support for the Toshiba Piccolo controllers. Currently only the
 675           primary channel is supported by this driver.
 676
 677           If unsure, say N.
 678
 679 config PATA_VIA
 680         tristate "VIA PATA support"
 681         depends on PCI
 682         help
 683           This option enables support for the VIA PATA interfaces
 684           found on the many VIA chipsets.
 685
 686           If unsure, say N.
 687
 688 config PATA_WINBOND
 689         tristate "Winbond SL82C105 PATA support"
 690         depends on PCI
 691         help
 692           This option enables support for SL82C105 PATA devices found in the
 693           Netwinder and some other systems
 694
 695           If unsure, say N.
 696
 697 config PATA_WINBOND_VLB
 698         tristate "Winbond W83759A VLB PATA support (Experimental)"
 699         depends on ISA && EXPERIMENTAL
 700         help
 701           Support for the Winbond W83759A controller on Vesa Local Bus
 702           systems.
 703
 704 config HAVE_PATA_PLATFORM
 705         bool
 706         help
 707           This is an internal configuration node for any machine that
 708           uses pata-platform driver to enable the relevant driver in the
 709           configuration structure without having to submit endless patches
 710           to update the PATA_PLATFORM entry.
 711
 712 config PATA_PLATFORM
 713         tristate "Generic platform device PATA support"
 714         depends on EMBEDDED || PPC || HAVE_PATA_PLATFORM
 715         help
 716           This option enables support for generic directly connected ATA
 717           devices commonly found on embedded systems.
 718
 719           If unsure, say N.
 720
 721 config PATA_AT91
 722         tristate "PATA support for AT91SAM9260"
 723         depends on ARM && ARCH_AT91
 724         help
 725           This option enables support for IDE devices on the Atmel AT91SAM9260 SoC.
 726
 727           If unsure, say N.
 728
 729 config PATA_OF_PLATFORM
 730         tristate "OpenFirmware platform device PATA support"
 731         depends on PATA_PLATFORM && PPC_OF
 732         help
 733           This option enables support for generic directly connected ATA
 734           devices commonly found on embedded systems with OpenFirmware
 735           bindings.
 736
 737           If unsure, say N.
 738
 739 config PATA_ICSIDE
 740         tristate "Acorn ICS PATA support"
 741         depends on ARM && ARCH_ACORN
 742         help
 743           On Acorn systems, say Y here if you wish to use the ICS PATA
 744           interface card.  This is not required for ICS partition support.
 745           If you are unsure, say N to this.
 746
 747 config PATA_IXP4XX_CF
 748         tristate "IXP4XX Compact Flash support"
 749         depends on ARCH_IXP4XX
 750         help
 751           This option enables support for a Compact Flash connected on
 752           the ixp4xx expansion bus. This driver had been written for
 753           Loft/Avila boards in mind but can work with others.
 754
 755           If unsure, say N.
 756
 757 config PATA_OCTEON_CF
 758         tristate "OCTEON Boot Bus Compact Flash support"
 759         depends on CPU_CAVIUM_OCTEON
 760         help
 761           This option enables a polled compact flash driver for use with
 762           compact flash cards attached to the OCTEON boot bus.
 763
 764           If unsure, say N.
 765
 766 config PATA_SCC
 767         tristate "Toshiba's Cell Reference Set IDE support"
 768         depends on PCI && PPC_CELLEB
 769         help
 770           This option enables support for the built-in IDE controller on
 771           Toshiba Cell Reference Board.
 772
 773           If unsure, say N.
 774
 775 config PATA_SCH
 776         tristate "Intel SCH PATA support"
 777         depends on PCI
 778         help
 779           This option enables support for Intel SCH PATA on the Intel
 780           SCH (US15W, US15L, UL11L) series host controllers.
 781
 782           If unsure, say N.
 783
 784 config PATA_BF54X
 785         tristate "Blackfin 54x ATAPI support"
 786         depends on BF542 || BF548 || BF549
 787         help
 788           This option enables support for the built-in ATAPI controller on
 789           Blackfin 54x family chips.
 790
 791           If unsure, say N.
 792
 793 config PATA_MACIO
 794         tristate "Apple PowerMac/PowerBook internal 'MacIO' IDE"
 795         depends on PPC_PMAC
 796         help
 797           Most IDE capable PowerMacs have IDE busses driven by a variant
 798           of this controller which is part of the Apple chipset used on
 799           most PowerMac models. Some models have multiple busses using
 800           different chipsets, though generally, MacIO is one of them.
 801
 802
 803 endif # ATA_SFF
 804 endif # ATA