drivers/ata/pata_serverworks.c

   1 /*
   2  * pata_serverworks.c   - Serverworks PATA for new ATA layer
   3  *                        (C) 2005 Red Hat Inc
   4  *                        Alan Cox <alan@redhat.com>
   5  *
   6  * based upon
   7  *
   8  * serverworks.c
   9  *
  10  * Copyright (C) 1998-2000 Michel Aubry
  11  * Copyright (C) 1998-2000 Andrzej Krzysztofowicz
  12  * Copyright (C) 1998-2000 Andre Hedrick <andre@linux-ide.org>
  13  * Portions copyright (c) 2001 Sun Microsystems
  14  *
  15  *
  16  * RCC/ServerWorks IDE driver for Linux
  17  *
  18  *   OSB4: `Open South Bridge' IDE Interface (fn 1)
  19  *         supports UDMA mode 2 (33 MB/s)
  20  *
  21  *   CSB5: `Champion South Bridge' IDE Interface (fn 1)
  22  *         all revisions support UDMA mode 4 (66 MB/s)
  23  *         revision A2.0 and up support UDMA mode 5 (100 MB/s)
  24  *
  25  *         *** The CSB5 does not provide ANY register ***
  26  *         *** to detect 80-conductor cable presence. ***
  27  *
  28  *   CSB6: `Champion South Bridge' IDE Interface (optional: third channel)
  29  *
  30  * Documentation:
  31  *      Available under NDA only. Errata info very hard to get.
  32  */
  33
  34 #include <linux/kernel.h>
  35 #include <linux/module.h>
  36 #include <linux/pci.h>
  37 #include <linux/init.h>
  38 #include <linux/blkdev.h>
  39 #include <linux/delay.h>
  40 #include <scsi/scsi_host.h>
  41 #include <linux/libata.h>
  42
  43 #define DRV_NAME "pata_serverworks"
  44 #define DRV_VERSION "0.4.2"
  45
  46 #define SVWKS_CSB5_REVISION_NEW 0x92 /* min PCI_REVISION_ID for UDMA5 (A2.0) */
  47 #define SVWKS_CSB6_REVISION     0xa0 /* min PCI_REVISION_ID for UDMA4 (A1.0) */
  48
  49 /* Seagate Barracuda ATA IV Family drives in UDMA mode 5
  50  * can overrun their FIFOs when used with the CSB5 */
  51
  52 static const char *csb_bad_ata100[] = {
  53         "ST320011A",
  54         "ST340016A",
  55         "ST360021A",
  56         "ST380021A",
  57         NULL
  58 };
  59
  60 /**
  61  *      dell_cable      -       Dell serverworks cable detection
  62  *      @ap: ATA port to do cable detect
  63  *
  64  *      Dell hide the 40/80 pin select for their interfaces in the top two
  65  *      bits of the subsystem ID.
  66  */
  67
  68 static int dell_cable(struct ata_port *ap) {
  69         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  70
  71         if (pdev->subsystem_device & (1 << (ap->port_no + 14)))
  72                 return ATA_CBL_PATA80;
  73         return ATA_CBL_PATA40;
  74 }
  75
  76 /**
  77  *      sun_cable       -       Sun Cobalt 'Alpine' cable detection
  78  *      @ap: ATA port to do cable select
  79  *
  80  *      Cobalt CSB5 IDE hides the 40/80pin in the top two bits of the
  81  *      subsystem ID the same as dell. We could use one function but we may
  82  *      need to extend the Dell one in future
  83  */
  84
  85 static int sun_cable(struct ata_port *ap) {
  86         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
  87
  88         if (pdev->subsystem_device & (1 << (ap->port_no + 14)))
  89                 return ATA_CBL_PATA80;
  90         return ATA_CBL_PATA40;
  91 }
  92
  93 /**
  94  *      osb4_cable      -       OSB4 cable detect
  95  *      @ap: ATA port to check
  96  *
  97  *      The OSB4 isn't UDMA66 capable so this is easy
  98  */
  99
 100 static int osb4_cable(struct ata_port *ap) {
 101         return ATA_CBL_PATA40;
 102 }
 103
 104 /**
 105  *      csb4_cable      -       CSB5/6 cable detect
 106  *      @ap: ATA port to check
 107  *
 108  *      Serverworks default arrangement is to use the drive side detection
 109  *      only.
 110  */
 111
 112 static int csb_cable(struct ata_port *ap) {
 113         return ATA_CBL_PATA80;
 114 }
 115
 116 struct sv_cable_table {
 117         int device;
 118         int subvendor;
 119         int (*cable_detect)(struct ata_port *ap);
 120 };
 121
 122 /*
 123  *      Note that we don't copy the old serverworks code because the old
 124  *      code contains obvious mistakes
 125  */
 126
 127 static struct sv_cable_table cable_detect[] = {
 128         { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_DELL, dell_cable },
 129         { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_VENDOR_ID_DELL, dell_cable },
 130         { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_VENDOR_ID_SUN,  sun_cable },
 131         { PCI_DEVICE_ID_SERVERWORKS_OSB4IDE, PCI_ANY_ID, osb4_cable },
 132         { PCI_DEVICE_ID_SERVERWORKS_CSB5IDE, PCI_ANY_ID, csb_cable },
 133         { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE, PCI_ANY_ID, csb_cable },
 134         { PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2, PCI_ANY_ID, csb_cable },
 135         { PCI_DEVICE_ID_SERVERWORKS_HT1000IDE, PCI_ANY_ID, csb_cable },
 136         { }
 137 };
 138
 139 /**
 140  *      serverworks_cable_detect        -       cable detection
 141  *      @ap: ATA port
 142  *      @deadline: deadline jiffies for the operation
 143  *
 144  *      Perform cable detection according to the device and subvendor
 145  *      identifications
 146  */
 147
 148 static int serverworks_cable_detect(struct ata_port *ap)
 149 {
 150         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 151         struct sv_cable_table *cb = cable_detect;
 152
 153         while(cb->device) {
 154                 if (cb->device == pdev->device &&
 155                     (cb->subvendor == pdev->subsystem_vendor ||
 156                       cb->subvendor == PCI_ANY_ID)) {
 157                         return cb->cable_detect(ap);
 158                 }
 159                 cb++;
 160         }
 161
 162         BUG();
 163         return -1;      /* kill compiler warning */
 164 }
 165
 166 /**
 167  *      serverworks_is_csb      -       Check for CSB or OSB
 168  *      @pdev: PCI device to check
 169  *
 170  *      Returns true if the device being checked is known to be a CSB
 171  *      series device.
 172  */
 173
 174 static u8 serverworks_is_csb(struct pci_dev *pdev)
 175 {
 176         switch (pdev->device) {
 177                 case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
 178                 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
 179                 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
 180                 case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
 181                         return 1;
 182                 default:
 183                         break;
 184         }
 185         return 0;
 186 }
 187
 188 /**
 189  *      serverworks_osb4_filter -       mode selection filter
 190  *      @adev: ATA device
 191  *      @mask: Mask of proposed modes
 192  *
 193  *      Filter the offered modes for the device to apply controller
 194  *      specific rules. OSB4 requires no UDMA for disks due to a FIFO
 195  *      bug we hit.
 196  */
 197
 198 static unsigned long serverworks_osb4_filter(struct ata_device *adev, unsigned long mask)
 199 {
 200         if (adev->class == ATA_DEV_ATA)
 201                 mask &= ~ATA_MASK_UDMA;
 202         return ata_pci_default_filter(adev, mask);
 203 }
 204
 205
 206 /**
 207  *      serverworks_csb_filter  -       mode selection filter
 208  *      @adev: ATA device
 209  *      @mask: Mask of proposed modes
 210  *
 211  *      Check the blacklist and disable UDMA5 if matched
 212  */
 213
 214 static unsigned long serverworks_csb_filter(struct ata_device *adev, unsigned long mask)
 215 {
 216         const char *p;
 217         char model_num[ATA_ID_PROD_LEN + 1];
 218         int i;
 219
 220         /* Disk, UDMA */
 221         if (adev->class != ATA_DEV_ATA)
 222                 return ata_pci_default_filter(adev, mask);
 223
 224         /* Actually do need to check */
 225         ata_id_c_string(adev->id, model_num, ATA_ID_PROD, sizeof(model_num));
 226
 227         for (i = 0; (p = csb_bad_ata100[i]) != NULL; i++) {
 228                 if (!strcmp(p, model_num))
 229                         mask &= ~(0x1F << ATA_SHIFT_UDMA);
 230         }
 231         return ata_pci_default_filter(adev, mask);
 232 }
 233
 234
 235 /**
 236  *      serverworks_set_piomode -       set initial PIO mode data
 237  *      @ap: ATA interface
 238  *      @adev: ATA device
 239  *
 240  *      Program the OSB4/CSB5 timing registers for PIO. The PIO register
 241  *      load is done as a simple lookup.
 242  */
 243 static void serverworks_set_piomode(struct ata_port *ap, struct ata_device *adev)
 244 {
 245         static const u8 pio_mode[] = { 0x5d, 0x47, 0x34, 0x22, 0x20 };
 246         int offset = 1 + (2 * ap->port_no) - adev->devno;
 247         int devbits = (2 * ap->port_no + adev->devno) * 4;
 248         u16 csb5_pio;
 249         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 250         int pio = adev->pio_mode - XFER_PIO_0;
 251
 252         pci_write_config_byte(pdev, 0x40 + offset, pio_mode[pio]);
 253
 254         /* The OSB4 just requires the timing but the CSB series want the
 255            mode number as well */
 256         if (serverworks_is_csb(pdev)) {
 257                 pci_read_config_word(pdev, 0x4A, &csb5_pio);
 258                 csb5_pio &= ~(0x0F << devbits);
 259                 pci_write_config_byte(pdev, 0x4A, csb5_pio | (pio << devbits));
 260         }
 261 }
 262
 263 /**
 264  *      serverworks_set_dmamode -       set initial DMA mode data
 265  *      @ap: ATA interface
 266  *      @adev: ATA device
 267  *
 268  *      Program the MWDMA/UDMA modes for the serverworks OSB4/CSB5
 269  *      chipset. The MWDMA mode values are pulled from a lookup table
 270  *      while the chipset uses mode number for UDMA.
 271  */
 272
 273 static void serverworks_set_dmamode(struct ata_port *ap, struct ata_device *adev)
 274 {
 275         static const u8 dma_mode[] = { 0x77, 0x21, 0x20 };
 276         int offset = 1 + 2 * ap->port_no - adev->devno;
 277         int devbits = (2 * ap->port_no + adev->devno);
 278         u8 ultra;
 279         u8 ultra_cfg;
 280         struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 281
 282         pci_read_config_byte(pdev, 0x54, &ultra_cfg);
 283
 284         if (adev->dma_mode >= XFER_UDMA_0) {
 285                 pci_write_config_byte(pdev, 0x44 + offset,  0x20);
 286
 287                 pci_read_config_byte(pdev, 0x56 + ap->port_no, &ultra);
 288                 ultra &= ~(0x0F << (ap->port_no * 4));
 289                 ultra |= (adev->dma_mode - XFER_UDMA_0)
 290                                         << (ap->port_no * 4);
 291                 pci_write_config_byte(pdev, 0x56 + ap->port_no, ultra);
 292
 293                 ultra_cfg |=  (1 << devbits);
 294         } else {
 295                 pci_write_config_byte(pdev, 0x44 + offset,
 296                         dma_mode[adev->dma_mode - XFER_MW_DMA_0]);
 297                 ultra_cfg &= ~(1 << devbits);
 298         }
 299         pci_write_config_byte(pdev, 0x54, ultra_cfg);
 300 }
 301
 302 static struct scsi_host_template serverworks_sht = {
 303         .module                 = THIS_MODULE,
 304         .name                   = DRV_NAME,
 305         .ioctl                  = ata_scsi_ioctl,
 306         .queuecommand           = ata_scsi_queuecmd,
 307         .can_queue              = ATA_DEF_QUEUE,
 308         .this_id                = ATA_SHT_THIS_ID,
 309         .sg_tablesize           = LIBATA_MAX_PRD,
 310         .cmd_per_lun            = ATA_SHT_CMD_PER_LUN,
 311         .emulated               = ATA_SHT_EMULATED,
 312         .use_clustering         = ATA_SHT_USE_CLUSTERING,
 313         .proc_name              = DRV_NAME,
 314         .dma_boundary           = ATA_DMA_BOUNDARY,
 315         .slave_configure        = ata_scsi_slave_config,
 316         .slave_destroy          = ata_scsi_slave_destroy,
 317         .bios_param             = ata_std_bios_param,
 318 };
 319
 320 static struct ata_port_operations serverworks_osb4_port_ops = {
 321         .set_piomode    = serverworks_set_piomode,
 322         .set_dmamode    = serverworks_set_dmamode,
 323         .mode_filter    = serverworks_osb4_filter,
 324
 325         .tf_load        = ata_tf_load,
 326         .tf_read        = ata_tf_read,
 327         .check_status   = ata_check_status,
 328         .exec_command   = ata_exec_command,
 329         .dev_select     = ata_std_dev_select,
 330
 331         .freeze         = ata_bmdma_freeze,
 332         .thaw           = ata_bmdma_thaw,
 333         .error_handler  = ata_bmdma_error_handler,
 334         .post_internal_cmd = ata_bmdma_post_internal_cmd,
 335         .cable_detect   = serverworks_cable_detect,
 336
 337         .bmdma_setup    = ata_bmdma_setup,
 338         .bmdma_start    = ata_bmdma_start,
 339         .bmdma_stop     = ata_bmdma_stop,
 340         .bmdma_status   = ata_bmdma_status,
 341
 342         .qc_prep        = ata_qc_prep,
 343         .qc_issue       = ata_qc_issue_prot,
 344
 345         .data_xfer      = ata_data_xfer,
 346
 347         .irq_handler    = ata_interrupt,
 348         .irq_clear      = ata_bmdma_irq_clear,
 349         .irq_on         = ata_irq_on,
 350
 351         .port_start     = ata_sff_port_start,
 352 };
 353
 354 static struct ata_port_operations serverworks_csb_port_ops = {
 355         .set_piomode    = serverworks_set_piomode,
 356         .set_dmamode    = serverworks_set_dmamode,
 357         .mode_filter    = serverworks_csb_filter,
 358
 359         .tf_load        = ata_tf_load,
 360         .tf_read        = ata_tf_read,
 361         .check_status   = ata_check_status,
 362         .exec_command   = ata_exec_command,
 363         .dev_select     = ata_std_dev_select,
 364
 365         .freeze         = ata_bmdma_freeze,
 366         .thaw           = ata_bmdma_thaw,
 367         .error_handler  = ata_bmdma_error_handler,
 368         .post_internal_cmd = ata_bmdma_post_internal_cmd,
 369         .cable_detect   = serverworks_cable_detect,
 370
 371         .bmdma_setup    = ata_bmdma_setup,
 372         .bmdma_start    = ata_bmdma_start,
 373         .bmdma_stop     = ata_bmdma_stop,
 374         .bmdma_status   = ata_bmdma_status,
 375
 376         .qc_prep        = ata_qc_prep,
 377         .qc_issue       = ata_qc_issue_prot,
 378
 379         .data_xfer      = ata_data_xfer,
 380
 381         .irq_handler    = ata_interrupt,
 382         .irq_clear      = ata_bmdma_irq_clear,
 383         .irq_on         = ata_irq_on,
 384
 385         .port_start     = ata_sff_port_start,
 386 };
 387
 388 static int serverworks_fixup_osb4(struct pci_dev *pdev)
 389 {
 390         u32 reg;
 391         struct pci_dev *isa_dev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
 392                   PCI_DEVICE_ID_SERVERWORKS_OSB4, NULL);
 393         if (isa_dev) {
 394                 pci_read_config_dword(isa_dev, 0x64, &reg);
 395                 reg &= ~0x00002000; /* disable 600ns interrupt mask */
 396                 if (!(reg & 0x00004000))
 397                         printk(KERN_DEBUG DRV_NAME ": UDMA not BIOS enabled.\n");
 398                 reg |=  0x00004000; /* enable UDMA/33 support */
 399                 pci_write_config_dword(isa_dev, 0x64, reg);
 400                 pci_dev_put(isa_dev);
 401                 return 0;
 402         }
 403         printk(KERN_WARNING "ata_serverworks: Unable to find bridge.\n");
 404         return -ENODEV;
 405 }
 406
 407 static int serverworks_fixup_csb(struct pci_dev *pdev)
 408 {
 409         u8 btr;
 410
 411         /* Third Channel Test */
 412         if (!(PCI_FUNC(pdev->devfn) & 1)) {
 413                 struct pci_dev * findev = NULL;
 414                 u32 reg4c = 0;
 415                 findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
 416                         PCI_DEVICE_ID_SERVERWORKS_CSB5, NULL);
 417                 if (findev) {
 418                         pci_read_config_dword(findev, 0x4C, &reg4c);
 419                         reg4c &= ~0x000007FF;
 420                         reg4c |=  0x00000040;
 421                         reg4c |=  0x00000020;
 422                         pci_write_config_dword(findev, 0x4C, reg4c);
 423                         pci_dev_put(findev);
 424                 }
 425         } else {
 426                 struct pci_dev * findev = NULL;
 427                 u8 reg41 = 0;
 428
 429                 findev = pci_get_device(PCI_VENDOR_ID_SERVERWORKS,
 430                                 PCI_DEVICE_ID_SERVERWORKS_CSB6, NULL);
 431                 if (findev) {
 432                         pci_read_config_byte(findev, 0x41, &reg41);
 433                         reg41 &= ~0x40;
 434                         pci_write_config_byte(findev, 0x41, reg41);
 435                         pci_dev_put(findev);
 436                 }
 437         }
 438         /* setup the UDMA Control register
 439          *
 440          * 1. clear bit 6 to enable DMA
 441          * 2. enable DMA modes with bits 0-1
 442          *      00 : legacy
 443          *      01 : udma2
 444          *      10 : udma2/udma4
 445          *      11 : udma2/udma4/udma5
 446          */
 447         pci_read_config_byte(pdev, 0x5A, &btr);
 448         btr &= ~0x40;
 449         if (!(PCI_FUNC(pdev->devfn) & 1))
 450                 btr |= 0x2;
 451         else
 452                 btr |= (pdev->revision >= SVWKS_CSB5_REVISION_NEW) ? 0x3 : 0x2;
 453         pci_write_config_byte(pdev, 0x5A, btr);
 454
 455         return btr;
 456 }
 457
 458 static void serverworks_fixup_ht1000(struct pci_dev *pdev)
 459 {
 460         u8 btr;
 461         /* Setup HT1000 SouthBridge Controller - Single Channel Only */
 462         pci_read_config_byte(pdev, 0x5A, &btr);
 463         btr &= ~0x40;
 464         btr |= 0x3;
 465         pci_write_config_byte(pdev, 0x5A, btr);
 466 }
 467
 468
 469 static int serverworks_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
 470 {
 471         static const struct ata_port_info info[4] = {
 472                 { /* OSB4 */
 473                         .sht = &serverworks_sht,
 474                         .flags = ATA_FLAG_SLAVE_POSS,
 475                         .pio_mask = 0x1f,
 476                         .mwdma_mask = 0x07,
 477                         .udma_mask = 0x07,
 478                         .port_ops = &serverworks_osb4_port_ops
 479                 }, { /* OSB4 no UDMA */
 480                         .sht = &serverworks_sht,
 481                         .flags = ATA_FLAG_SLAVE_POSS,
 482                         .pio_mask = 0x1f,
 483                         .mwdma_mask = 0x07,
 484                         .udma_mask = 0x00,
 485                         .port_ops = &serverworks_osb4_port_ops
 486                 }, { /* CSB5 */
 487                         .sht = &serverworks_sht,
 488                         .flags = ATA_FLAG_SLAVE_POSS,
 489                         .pio_mask = 0x1f,
 490                         .mwdma_mask = 0x07,
 491                         .udma_mask = ATA_UDMA4,
 492                         .port_ops = &serverworks_csb_port_ops
 493                 }, { /* CSB5 - later revisions*/
 494                         .sht = &serverworks_sht,
 495                         .flags = ATA_FLAG_SLAVE_POSS,
 496                         .pio_mask = 0x1f,
 497                         .mwdma_mask = 0x07,
 498                         .udma_mask = ATA_UDMA5,
 499                         .port_ops = &serverworks_csb_port_ops
 500                 }
 501         };
 502         const struct ata_port_info *ppi[] = { &info[id->driver_data], NULL };
 503
 504         /* Force master latency timer to 64 PCI clocks */
 505         pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40);
 506
 507         /* OSB4 : South Bridge and IDE */
 508         if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_OSB4IDE) {
 509                 /* Select non UDMA capable OSB4 if we can't do fixups */
 510                 if ( serverworks_fixup_osb4(pdev) < 0)
 511                         ppi[0] = &info[1];
 512         }
 513         /* setup CSB5/CSB6 : South Bridge and IDE option RAID */
 514         else if ((pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE) ||
 515                  (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE) ||
 516                  (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)) {
 517
 518                  /* If the returned btr is the newer revision then
 519                     select the right info block */
 520                  if (serverworks_fixup_csb(pdev) == 3)
 521                         ppi[0] = &info[3];
 522
 523                 /* Is this the 3rd channel CSB6 IDE ? */
 524                 if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2)
 525                         ppi[1] = &ata_dummy_port_info;
 526         }
 527         /* setup HT1000E */
 528         else if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_HT1000IDE)
 529                 serverworks_fixup_ht1000(pdev);
 530
 531         if (pdev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5IDE)
 532                 ata_pci_clear_simplex(pdev);
 533
 534         return ata_pci_init_one(pdev, ppi);
 535 }
 536
 537 #ifdef CONFIG_PM
 538 static int serverworks_reinit_one(struct pci_dev *pdev)
 539 {
 540         /* Force master latency timer to 64 PCI clocks */
 541         pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x40);
 542
 543         switch (pdev->device)
 544         {
 545                 case PCI_DEVICE_ID_SERVERWORKS_OSB4IDE:
 546                         serverworks_fixup_osb4(pdev);
 547                         break;
 548                 case PCI_DEVICE_ID_SERVERWORKS_CSB5IDE:
 549                         ata_pci_clear_simplex(pdev);
 550                         /* fall through */
 551                 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE:
 552                 case PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2:
 553                         serverworks_fixup_csb(pdev);
 554                         break;
 555                 case PCI_DEVICE_ID_SERVERWORKS_HT1000IDE:
 556                         serverworks_fixup_ht1000(pdev);
 557                         break;
 558         }
 559         return ata_pci_device_resume(pdev);
 560 }
 561 #endif
 562
 563 static const struct pci_device_id serverworks[] = {
 564         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_OSB4IDE), 0},
 565         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB5IDE), 2},
 566         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE), 2},
 567         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_CSB6IDE2), 2},
 568         { PCI_VDEVICE(SERVERWORKS, PCI_DEVICE_ID_SERVERWORKS_HT1000IDE), 2},
 569
 570         { },
 571 };
 572
 573 static struct pci_driver serverworks_pci_driver = {
 574         .name           = DRV_NAME,
 575         .id_table       = serverworks,
 576         .probe          = serverworks_init_one,
 577         .remove         = ata_pci_remove_one,
 578 #ifdef CONFIG_PM
 579         .suspend        = ata_pci_device_suspend,
 580         .resume         = serverworks_reinit_one,
 581 #endif
 582 };
 583
 584 static int __init serverworks_init(void)
 585 {
 586         return pci_register_driver(&serverworks_pci_driver);
 587 }
 588
 589 static void __exit serverworks_exit(void)
 590 {
 591         pci_unregister_driver(&serverworks_pci_driver);
 592 }
 593
 594 MODULE_AUTHOR("Alan Cox");
 595 MODULE_DESCRIPTION("low-level driver for Serverworks OSB4/CSB5/CSB6");
 596 MODULE_LICENSE("GPL");
 597 MODULE_DEVICE_TABLE(pci, serverworks);
 598 MODULE_VERSION(DRV_VERSION);
 599
 600 module_init(serverworks_init);
 601 module_exit(serverworks_exit);