drivers/clk/ti/dpll44xx.c

   1 /*
   2  * OMAP4-specific DPLL control functions
   3  *
   4  * Copyright (C) 2011 Texas Instruments, Inc.
   5  * Rajendra Nayak
   6  *
   7  * This program is free software; you can redistribute it and/or modify
   8  * it under the terms of the GNU General Public License version 2 as
   9  * published by the Free Software Foundation.
  10  */
  11
  12 #include <linux/kernel.h>
  13 #include <linux/errno.h>
  14 #include <linux/clk.h>
  15 #include <linux/io.h>
  16 #include <linux/bitops.h>
  17 #include <linux/clk/ti.h>
  18
  19 #include "clock.h"
  20
  21 /*
  22  * Maximum DPLL input frequency (FINT) and output frequency (FOUT) that
  23  * can supported when using the DPLL low-power mode. Frequencies are
  24  * defined in OMAP4430/60 Public TRM section 3.6.3.3.2 "Enable Control,
  25  * Status, and Low-Power Operation Mode".
  26  */
  27 #define OMAP4_DPLL_LP_FINT_MAX  1000000
  28 #define OMAP4_DPLL_LP_FOUT_MAX  100000000
  29
  30 /*
  31  * Bitfield declarations
  32  */
  33 #define OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK             BIT(8)
  34 #define OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK           BIT(10)
  35 #define OMAP4430_DPLL_REGM4XEN_MASK                     BIT(11)
  36
  37 /* Static rate multiplier for OMAP4 REGM4XEN clocks */
  38 #define OMAP4430_REGM4XEN_MULT                          4
  39
  40 static void omap4_dpllmx_allow_gatectrl(struct clk_hw_omap *clk)
  41 {
  42         u32 v;
  43         u32 mask;
  44
  45         if (!clk || !clk->clksel_reg)
  46                 return;
  47
  48         mask = clk->flags & CLOCK_CLKOUTX2 ?
  49                         OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK :
  50                         OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK;
  51
  52         v = ti_clk_ll_ops->clk_readl(clk->clksel_reg);
  53         /* Clear the bit to allow gatectrl */
  54         v &= ~mask;
  55         ti_clk_ll_ops->clk_writel(v, clk->clksel_reg);
  56 }
  57
  58 static void omap4_dpllmx_deny_gatectrl(struct clk_hw_omap *clk)
  59 {
  60         u32 v;
  61         u32 mask;
  62
  63         if (!clk || !clk->clksel_reg)
  64                 return;
  65
  66         mask = clk->flags & CLOCK_CLKOUTX2 ?
  67                         OMAP4430_DPLL_CLKOUTX2_GATE_CTRL_MASK :
  68                         OMAP4430_DPLL_CLKOUT_GATE_CTRL_MASK;
  69
  70         v = ti_clk_ll_ops->clk_readl(clk->clksel_reg);
  71         /* Set the bit to deny gatectrl */
  72         v |= mask;
  73         ti_clk_ll_ops->clk_writel(v, clk->clksel_reg);
  74 }
  75
  76 const struct clk_hw_omap_ops clkhwops_omap4_dpllmx = {
  77         .allow_idle     = omap4_dpllmx_allow_gatectrl,
  78         .deny_idle      = omap4_dpllmx_deny_gatectrl,
  79 };
  80
  81 /**
  82  * omap4_dpll_lpmode_recalc - compute DPLL low-power setting
  83  * @dd: pointer to the dpll data structure
  84  *
  85  * Calculates if low-power mode can be enabled based upon the last
  86  * multiplier and divider values calculated. If low-power mode can be
  87  * enabled, then the bit to enable low-power mode is stored in the
  88  * last_rounded_lpmode variable. This implementation is based upon the
  89  * criteria for enabling low-power mode as described in the OMAP4430/60
  90  * Public TRM section 3.6.3.3.2 "Enable Control, Status, and Low-Power
  91  * Operation Mode".
  92  */
  93 static void omap4_dpll_lpmode_recalc(struct dpll_data *dd)
  94 {
  95         long fint, fout;
  96
  97         fint = __clk_get_rate(dd->clk_ref) / (dd->last_rounded_n + 1);
  98         fout = fint * dd->last_rounded_m;
  99
 100         if ((fint < OMAP4_DPLL_LP_FINT_MAX) && (fout < OMAP4_DPLL_LP_FOUT_MAX))
 101                 dd->last_rounded_lpmode = 1;
 102         else
 103                 dd->last_rounded_lpmode = 0;
 104 }
 105
 106 /**
 107  * omap4_dpll_regm4xen_recalc - compute DPLL rate, considering REGM4XEN bit
 108  * @clk: struct clk * of the DPLL to compute the rate for
 109  *
 110  * Compute the output rate for the OMAP4 DPLL represented by @clk.
 111  * Takes the REGM4XEN bit into consideration, which is needed for the
 112  * OMAP4 ABE DPLL.  Returns the DPLL's output rate (before M-dividers)
 113  * upon success, or 0 upon error.
 114  */
 115 unsigned long omap4_dpll_regm4xen_recalc(struct clk_hw *hw,
 116                                          unsigned long parent_rate)
 117 {
 118         struct clk_hw_omap *clk = to_clk_hw_omap(hw);
 119         u32 v;
 120         unsigned long rate;
 121         struct dpll_data *dd;
 122
 123         if (!clk || !clk->dpll_data)
 124                 return 0;
 125
 126         dd = clk->dpll_data;
 127
 128         rate = omap2_get_dpll_rate(clk);
 129
 130         /* regm4xen adds a multiplier of 4 to DPLL calculations */
 131         v = ti_clk_ll_ops->clk_readl(dd->control_reg);
 132         if (v & OMAP4430_DPLL_REGM4XEN_MASK)
 133                 rate *= OMAP4430_REGM4XEN_MULT;
 134
 135         return rate;
 136 }
 137
 138 /**
 139  * omap4_dpll_regm4xen_round_rate - round DPLL rate, considering REGM4XEN bit
 140  * @clk: struct clk * of the DPLL to round a rate for
 141  * @target_rate: the desired rate of the DPLL
 142  *
 143  * Compute the rate that would be programmed into the DPLL hardware
 144  * for @clk if set_rate() were to be provided with the rate
 145  * @target_rate.  Takes the REGM4XEN bit into consideration, which is
 146  * needed for the OMAP4 ABE DPLL.  Returns the rounded rate (before
 147  * M-dividers) upon success, -EINVAL if @clk is null or not a DPLL, or
 148  * ~0 if an error occurred in omap2_dpll_round_rate().
 149  */
 150 long omap4_dpll_regm4xen_round_rate(struct clk_hw *hw,
 151                                     unsigned long target_rate,
 152                                     unsigned long *parent_rate)
 153 {
 154         struct clk_hw_omap *clk = to_clk_hw_omap(hw);
 155         struct dpll_data *dd;
 156         long r;
 157
 158         if (!clk || !clk->dpll_data)
 159                 return -EINVAL;
 160
 161         dd = clk->dpll_data;
 162
 163         dd->last_rounded_m4xen = 0;
 164
 165         /*
 166          * First try to compute the DPLL configuration for
 167          * target rate without using the 4X multiplier.
 168          */
 169         r = omap2_dpll_round_rate(hw, target_rate, NULL);
 170         if (r != ~0)
 171                 goto out;
 172
 173         /*
 174          * If we did not find a valid DPLL configuration, try again, but
 175          * this time see if using the 4X multiplier can help. Enabling the
 176          * 4X multiplier is equivalent to dividing the target rate by 4.
 177          */
 178         r = omap2_dpll_round_rate(hw, target_rate / OMAP4430_REGM4XEN_MULT,
 179                                   NULL);
 180         if (r == ~0)
 181                 return r;
 182
 183         dd->last_rounded_rate *= OMAP4430_REGM4XEN_MULT;
 184         dd->last_rounded_m4xen = 1;
 185
 186 out:
 187         omap4_dpll_lpmode_recalc(dd);
 188
 189         return dd->last_rounded_rate;
 190 }
 191
 192 /**
 193  * omap4_dpll_regm4xen_determine_rate - determine rate for a DPLL
 194  * @hw: pointer to the clock to determine rate for
 195  * @req: target rate request
 196  *
 197  * Determines which DPLL mode to use for reaching a desired rate.
 198  * Checks whether the DPLL shall be in bypass or locked mode, and if
 199  * locked, calculates the M,N values for the DPLL via round-rate.
 200  * Returns 0 on success and a negative error value otherwise.
 201  */
 202 int omap4_dpll_regm4xen_determine_rate(struct clk_hw *hw,
 203                                        struct clk_rate_request *req)
 204 {
 205         struct clk_hw_omap *clk = to_clk_hw_omap(hw);
 206         struct dpll_data *dd;
 207
 208         if (!req->rate)
 209                 return -EINVAL;
 210
 211         dd = clk->dpll_data;
 212         if (!dd)
 213                 return -EINVAL;
 214
 215         if (__clk_get_rate(dd->clk_bypass) == req->rate &&
 216             (dd->modes & (1 << DPLL_LOW_POWER_BYPASS))) {
 217                 req->best_parent_hw = __clk_get_hw(dd->clk_bypass);
 218         } else {
 219                 req->rate = omap4_dpll_regm4xen_round_rate(hw, req->rate,
 220                                                 &req->best_parent_rate);
 221                 req->best_parent_hw = __clk_get_hw(dd->clk_ref);
 222         }
 223
 224         req->best_parent_rate = req->rate;
 225
 226         return 0;
 227 }