2 # GPIO infrastructure and drivers
5 config ARCH_HAVE_CUSTOM_GPIO_H
8 Selecting this config option from the architecture Kconfig allows
9 the architecture to provide a custom asm/gpio.h implementation
10 overriding the default implementations. New uses of this are
13 config ARCH_WANT_OPTIONAL_GPIOLIB
16 Select this config option from the architecture Kconfig, if
17 it is possible to use gpiolib on the architecture, but let the
18 user decide whether to actually build it or not.
19 Select this instead of ARCH_REQUIRE_GPIOLIB, if your architecture does
20 not depend on GPIOs being available, but rather let the user
21 decide whether he needs it or not.
23 config ARCH_REQUIRE_GPIOLIB
27 Platforms select gpiolib if they use this infrastructure
28 for all their GPIOs, usually starting with ones integrated
30 Selecting this from the architecture code will cause the gpiolib
31 code to always get built in.
36 depends on ARCH_WANT_OPTIONAL_GPIOLIB || ARCH_REQUIRE_GPIOLIB
38 This enables GPIO support through the generic GPIO library.
39 You only need to enable this, if you also want to enable
40 one or more of the GPIO drivers below.
58 config GPIOLIB_IRQCHIP
63 bool "Debug GPIO calls"
64 depends on DEBUG_KERNEL
66 Say Y here to add some extra checks and diagnostics to GPIO calls.
67 These checks help ensure that GPIOs have been properly initialized
68 before they are used, and that sleeping calls are not made from
69 non-sleeping contexts. They can make bitbanged serial protocols
70 slower. The diagnostics help catch the type of setup errors
71 that are most common when setting up new platforms or boards.
74 bool "/sys/class/gpio/... (sysfs interface)"
77 Say Y here to add a sysfs interface for GPIOs.
79 This is mostly useful to work around omissions in a system's
80 kernel support. Those are common in custom and semicustom
81 hardware assembled using standard kernels with a minimum of
82 custom patches. In those cases, userspace code may import
83 a given GPIO from the kernel, if no kernel driver requested it.
85 Kernel drivers may also request that a particular GPIO be
86 exported to userspace; this can be useful when debugging.
91 # put drivers in the right section, in alphabetical order
94 tristate "Dialog DA9052 GPIO"
95 depends on PMIC_DA9052
97 Say yes here to enable the GPIO driver for the DA9052 chip.
100 tristate "Dialog Semiconductor DA9055 GPIO"
101 depends on MFD_DA9055
103 Say yes here to enable the GPIO driver for the DA9055 chip.
105 The Dialog DA9055 PMIC chip has 3 GPIO pins that can be
106 be controller by this driver.
108 If driver is built as a module it will be called gpio-da9055.
113 comment "Memory mapped GPIO drivers:"
115 config GPIO_74XX_MMIO
116 tristate "GPIO driver for 74xx-ICs with MMIO access"
120 Say yes here to support GPIO functionality for 74xx-compatible ICs
121 with MMIO access. Compatible models include:
122 1 bit: 741G125 (Input), 741G74 (Output)
123 2 bits: 742G125 (Input), 7474 (Output)
124 4 bits: 74125 (Input), 74175 (Output)
125 6 bits: 74365 (Input), 74174 (Output)
126 8 bits: 74244 (Input), 74273 (Output)
127 16 bits: 741624 (Input), 7416374 (Output)
130 tristate "CLPS711X GPIO support"
131 depends on ARCH_CLPS711X || COMPILE_TEST
134 Say yes here to support GPIO on CLPS711X SoCs.
137 bool "TI Davinci/Keystone GPIO support"
138 default y if ARCH_DAVINCI
139 depends on ARM && (ARCH_DAVINCI || ARCH_KEYSTONE)
141 Say yes here to enable GPIO support for TI Davinci/Keystone SoCs.
143 config GPIO_GENERIC_PLATFORM
144 tristate "Generic memory-mapped GPIO controller support (MMIO platform device)"
147 Say yes here to support basic platform_device memory-mapped GPIO controllers.
150 tristate "Synopsys DesignWare APB GPIO driver"
154 select GENERIC_IRQ_CHIP
156 Say Y or M here to build support for the Synopsys DesignWare APB
160 tristate "IT8761E GPIO support"
161 depends on X86 # unconditional access to IO space.
163 Say yes here to support GPIO functionality of IT8761E super I/O chip.
166 tristate "Emma Mobile GPIO"
167 depends on ARM && OF_GPIO
169 Say yes here to support GPIO on Renesas Emma Mobile SoCs.
173 depends on ARCH_EP93XX
177 bool "LSI ZEVIO SoC memory mapped GPIOs"
178 depends on ARM && OF_GPIO
180 Say yes here to support the GPIO controller in LSI ZEVIO SoCs.
182 config GPIO_MM_LANTIQ
183 bool "Lantiq Memory mapped GPIOs"
184 depends on LANTIQ && SOC_XWAY
186 This enables support for memory mapped GPIOs on the External Bus Unit
187 (EBU) found on Lantiq SoCs. The gpios are output only as they are
188 created by attaching a 16bit latch to the bus.
191 tristate "F71882FG and F71889F GPIO support"
194 This option enables support for GPIOs found on Fintek Super-I/O
195 chips F71882FG and F71889F.
197 To compile this driver as a module, choose M here: the module will
198 be called f7188x-gpio.
201 bool "MOXART GPIO support"
202 depends on ARCH_MOXART
205 Select this option to enable GPIO driver for
206 MOXA ART SoC devices.
210 depends on PPC_MPC52xx
213 bool "MPC512x/MPC8xxx GPIO support"
214 depends on PPC_MPC512x || PPC_MPC831x || PPC_MPC834x || PPC_MPC837x || \
215 FSL_SOC_BOOKE || PPC_86xx
217 Say Y here if you're going to use hardware that connects to the
218 MPC512x/831x/834x/837x/8572/8610 GPIOs.
221 tristate "Qualcomm MSM GPIO v1"
222 depends on GPIOLIB && ARCH_MSM && (ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50)
224 Say yes here to support the GPIO interface on ARM v6 based
225 Qualcomm MSM chips. Most of the pins on the MSM can be
226 selected for GPIO, and are controlled by this driver.
229 tristate "Qualcomm MSM GPIO v2"
230 depends on GPIOLIB && OF && ARCH_QCOM
232 Say yes here to support the GPIO interface on ARM v7 based
233 Qualcomm MSM chips. Most of the pins on the MSM can be
234 selected for GPIO, and are controlled by this driver.
238 depends on PLAT_ORION
241 select GENERIC_IRQ_CHIP
247 select GENERIC_IRQ_CHIP
253 select GENERIC_IRQ_CHIP
256 tristate "Cavium OCTEON GPIO"
257 depends on GPIOLIB && CAVIUM_OCTEON_SOC
260 Say yes here to support the on-chip GPIO lines on the OCTEON
264 bool "TI OMAP GPIO support" if COMPILE_TEST && !ARCH_OMAP2PLUS
265 default y if ARCH_OMAP
267 select GENERIC_IRQ_CHIP
268 select GPIOLIB_IRQCHIP
270 Say yes here to enable GPIO support for TI OMAP SoCs.
273 bool "PrimeCell PL061 GPIO support"
276 select GPIOLIB_IRQCHIP
278 Say yes here to support the PrimeCell PL061 GPIO device
281 bool "PXA GPIO support"
282 depends on ARCH_PXA || ARCH_MMP
284 Say yes here to support the PXA GPIO device
287 tristate "Renesas R-Car GPIO"
288 depends on ARM && (ARCH_SHMOBILE || COMPILE_TEST)
289 select GPIOLIB_IRQCHIP
291 Say yes here to support GPIO on Renesas R-Car SoCs.
295 depends on PLAT_SAMSUNG
297 Legacy GPIO support. Use only for platforms without support for
301 tristate "SMSC SCH311x SuperI/O GPIO"
303 Driver to enable the GPIOs found on SMSC SMSC SCH3112, SCH3114 and
304 SCH3116 "Super I/O" chipsets.
306 To compile this driver as a module, choose M here: the module will
307 be called gpio-sch311x.
309 config GPIO_SPEAR_SPICS
310 bool "ST SPEAr13xx SPI Chip Select as GPIO support"
311 depends on PLAT_SPEAR
312 select GENERIC_IRQ_CHIP
314 Say yes here to support ST SPEAr SPI Chip Select as GPIO device
317 bool "STA2x11/ConneXt GPIO support"
318 depends on MFD_STA2X11
319 select GENERIC_IRQ_CHIP
321 Say yes here to support the STA2x11/ConneXt GPIO device.
322 The GPIO module has 128 GPIO pins with alternate functions.
325 tristate "GPIO based on SYSCON"
326 depends on MFD_SYSCON && OF
328 Say yes here to support GPIO functionality though SYSCON driver.
331 tristate "TS-5500 DIO blocks and compatibles"
332 depends on TS5500 || COMPILE_TEST
334 This driver supports Digital I/O exposed by pin blocks found on some
335 Technologic Systems platforms. It includes, but is not limited to, 3
336 blocks of the TS-5500: DIO1, DIO2 and the LCD port, and the TS-5600
340 bool "Toumaz Xenif TZ1090 GPIO support"
341 depends on SOC_TZ1090
342 select GENERIC_IRQ_CHIP
345 Say yes here to support Toumaz Xenif TZ1090 GPIOs.
347 config GPIO_TZ1090_PDC
348 bool "Toumaz Xenif TZ1090 PDC GPIO support"
349 depends on SOC_TZ1090
352 Say yes here to support Toumaz Xenif TZ1090 PDC GPIOs.
356 depends on ARCH_MXC && SOC_VF610
357 select GPIOLIB_IRQCHIP
359 Say yes here to support Vybrid vf610 GPIOs.
362 bool "APM X-Gene GPIO controller support"
363 depends on ARM64 && OF_GPIO
365 This driver is to support the GPIO block within the APM X-Gene SoC
366 platform's generic flash controller. The GPIO pins are muxed with
367 the generic flash controller's address and data pins. Say yes
368 here to enable the GFC GPIO functionality.
371 tristate "Xilinx GPIO support"
372 depends on OF_GPIO && (PPC_OF || MICROBLAZE || ARCH_ZYNQ || ARCH_X86)
374 Say yes here to support the Xilinx FPGA GPIO device
377 tristate "Xilinx Zynq GPIO support"
379 select GPIOLIB_IRQCHIP
381 Say yes here to support Xilinx Zynq GPIO controller.
384 bool "Xtensa GPIO32 support"
386 depends on HAVE_XTENSA_GPIO32
389 Say yes here to support the Xtensa internal GPIO32 IMPWIRE (input)
390 and EXPSTATE (output) ports
393 tristate "NEC VR4100 series General-purpose I/O Uint support"
394 depends on CPU_VR41XX
396 Say yes here to support the NEC VR4100 series General-purpose I/O Uint
399 tristate "Intel SCH/TunnelCreek/Centerton/Quark X1000 GPIO"
400 depends on PCI && X86
404 Say yes here to support GPIO interface on Intel Poulsbo SCH,
405 Intel Tunnel Creek processor, Intel Centerton processor or
406 Intel Quark X1000 SoC.
408 The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are
409 powered by the core power rail and are turned off during sleep
410 modes (S3 and higher). The remaining four GPIOs are powered by
411 the Intel SCH suspend power supply. These GPIOs remain
412 active during S3. The suspend powered GPIOs can be used to wake the
413 system from the Suspend-to-RAM state.
415 The Intel Tunnel Creek processor has 5 GPIOs powered by the
416 core power rail and 9 from suspend power supply.
418 The Intel Centerton processor has a total of 30 GPIO pins.
419 Twenty-one are powered by the core power rail and 9 from the
420 suspend power supply.
422 The Intel Quark X1000 SoC has 2 GPIOs powered by the core
423 power well and 6 from the suspend power well.
426 tristate "Intel ICH GPIO"
427 depends on PCI && X86
431 Say yes here to support the GPIO functionality of a number of Intel
432 ICH-based chipsets. Currently supported devices: ICH6, ICH7, ICH8
433 ICH9, ICH10, Series 5/3400 (eg Ibex Peak), Series 6/C200 (eg
434 Cougar Point), NM10 (Tiger Point), and 3100 (Whitmore Lake).
439 tristate "Intel IOP GPIO"
440 depends on ARM && (ARCH_IOP32X || ARCH_IOP33X)
442 Say yes here to support the GPIO functionality of a number of Intel
448 tristate "VIA VX855/VX875 GPIO"
453 Support access to the VX855/VX875 GPIO lines through the gpio library.
455 This driver provides common support for accessing the device,
456 additional drivers must be enabled in order to use the
457 functionality of the device.
460 bool "GE FPGA based GPIO"
463 Support for common GPIO functionality provided on some GE Single Board
466 This driver provides basic support (configure as input or output, read
467 and write pin state) for GPIO implemented in a number of GE single
470 config GPIO_LYNXPOINT
471 tristate "Intel Lynxpoint GPIO support"
472 depends on ACPI && X86
473 select GPIOLIB_IRQCHIP
475 driver for GPIO functionality on Intel Lynxpoint PCH chipset
476 Requires ACPI device enumeration code to set up a platform device.
479 tristate "Aeroflex Gaisler GRGPIO support"
484 Select this to support Aeroflex Gaisler GRGPIO cores from the GRLIB
485 VHDL IP core library.
489 select GENERIC_IRQ_CHIP
492 comment "I2C GPIO expanders:"
495 tristate "Wolfson Microelectronics Arizona class devices"
496 depends on MFD_ARIZONA
498 Support for GPIOs on Wolfson Arizona class devices.
500 config GPIO_CRYSTAL_COVE
501 tristate "GPIO support for Crystal Cove PMIC"
502 depends on INTEL_SOC_PMIC
503 select GPIOLIB_IRQCHIP
505 Support for GPIO pins on Crystal Cove PMIC.
507 Say Yes if you have a Intel SoC based tablet with Crystal Cove PMIC
510 This driver can also be built as a module. If so, the module will be
511 called gpio-crystalcove.
514 tristate "TI/National Semiconductor LP3943 GPIO expander"
515 depends on MFD_LP3943
517 GPIO driver for LP3943 MFD.
518 LP3943 can be used as a GPIO expander which provides up to 16 GPIOs.
519 Open drain outputs are required for this usage.
522 tristate "Maxim MAX7300 GPIO expander"
526 GPIO driver for Maxim MAX7300 I2C-based GPIO expander.
529 tristate "MAX7319, MAX7320-7327 I2C Port Expanders"
532 Say yes here to support the MAX7319, MAX7320-7327 series of I2C
533 Port Expanders. Each IO port on these chips has a fixed role of
534 Input (designated by 'I'), Push-Pull Output ('O'), or Open-Drain
535 Input and Output (designed by 'P'). The combinations are listed
538 8 bits: max7319 (8I), max7320 (8O), max7321 (8P),
539 max7322 (4I4O), max7323 (4P4O)
541 16 bits: max7324 (8I8O), max7325 (8P8O),
542 max7326 (4I12O), max7327 (4P12O)
544 Board setup code must specify the model to use, and the start
545 number for these GPIOs.
547 config GPIO_MAX732X_IRQ
548 bool "Interrupt controller support for MAX732x"
549 depends on GPIO_MAX732X=y
551 Say yes here to enable the max732x to be used as an interrupt
552 controller. It requires the driver to be built in the kernel.
554 config GPIO_MC9S08DZ60
555 bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions"
556 depends on I2C=y && MACH_MX35_3DS
558 Select this to enable the MC9S08DZ60 GPIO driver
561 tristate "PCA95[357]x, PCA9698, TCA64xx, and MAX7310 I/O ports"
564 Say yes here to provide access to several register-oriented
565 SMBus I/O expanders, made mostly by NXP or TI. Compatible
568 4 bits: pca9536, pca9537
570 8 bits: max7310, max7315, pca6107, pca9534, pca9538, pca9554,
571 pca9556, pca9557, pca9574, tca6408, xra1202
573 16 bits: max7312, max7313, pca9535, pca9539, pca9555, pca9575,
578 40 bits: pca9505, pca9698
580 config GPIO_PCA953X_IRQ
581 bool "Interrupt controller support for PCA953x"
582 depends on GPIO_PCA953X=y
583 select GPIOLIB_IRQCHIP
585 Say yes here to enable the pca953x to be used as an interrupt
586 controller. It requires the driver to be built in the kernel.
589 tristate "PCF857x, PCA{85,96}7x, and MAX732[89] I2C GPIO expanders"
593 Say yes here to provide access to most "quasi-bidirectional" I2C
594 GPIO expanders used for additional digital outputs or inputs.
595 Most of these parts are from NXP, though TI is a second source for
596 some of them. Compatible models include:
598 8 bits: pcf8574, pcf8574a, pca8574, pca8574a,
599 pca9670, pca9672, pca9674, pca9674a,
602 16 bits: pcf8575, pcf8575c, pca8575,
603 pca9671, pca9673, pca9675
605 Your board setup code will need to declare the expanders in
606 use, and assign numbers to the GPIOs they expose. Those GPIOs
607 can then be used from drivers and other kernel code, just like
608 other GPIOs, but only accessible from task contexts.
610 This driver provides an in-kernel interface to those GPIOs using
611 platform-neutral GPIO calls.
614 bool "RICOH RC5T583 GPIO"
615 depends on MFD_RC5T583
617 Select this option to enable GPIO driver for the Ricoh RC5T583
619 This driver provides the support for driving/reading the gpio pins
620 of RC5T583 device through standard gpio library.
623 bool "Semtech SX150x I2C GPIO expander"
625 select GPIOLIB_IRQCHIP
628 Say yes here to provide support for Semtech SX150-series I2C
629 GPIO expanders. Compatible models include:
637 select GPIOLIB_IRQCHIP
639 This enables support for the GPIOs found on the STMPE I/O
643 bool "XWAY STP GPIOs"
646 This enables support for the Serial To Parallel (STP) unit found on
647 XWAY SoC. The STP allows the SoC to drive a shift registers cascade,
648 that can be up to 24 bit. This peripheral is aimed at driving leds.
649 Some of the gpios/leds can be auto updated by the soc with dsl and
654 depends on MFD_TC3589X
655 select GPIOLIB_IRQCHIP
657 This enables support for the GPIOs found on the TC3589X
661 tristate "TI TPS65912 GPIO"
662 depends on (MFD_TPS65912_I2C || MFD_TPS65912_SPI)
664 This driver supports TPS65912 gpio chip
667 tristate "TWL4030, TWL5030, and TPS659x0 GPIOs"
668 depends on TWL4030_CORE
670 Say yes here to access the GPIO signals of various multi-function
671 power management chips from Texas Instruments.
674 tristate "TWL6040 GPO"
675 depends on TWL6040_CORE
677 Say yes here to access the GPO signals of twl6040
678 audio chip from Texas Instruments.
681 tristate "WM831x GPIOs"
682 depends on MFD_WM831X
684 Say yes here to access the GPIO signals of WM831x power management
685 chips from Wolfson Microelectronics.
688 tristate "WM8350 GPIOs"
689 depends on MFD_WM8350
691 Say yes here to access the GPIO signals of WM8350 power management
692 chips from Wolfson Microelectronics.
695 tristate "WM8994 GPIOs"
696 depends on MFD_WM8994
698 Say yes here to access the GPIO signals of WM8994 audio hub
699 CODECs from Wolfson Microelectronics.
702 tristate "GPIO Support for ADP5520 PMIC"
703 depends on PMIC_ADP5520
705 This option enables support for on-chip GPIO found
706 on Analog Devices ADP5520 PMICs.
709 tristate "ADP5588 I2C GPIO expander"
712 This option enables support for 18 GPIOs found
713 on Analog Devices ADP5588 GPIO Expanders.
715 config GPIO_ADP5588_IRQ
716 bool "Interrupt controller support for ADP5588"
717 depends on GPIO_ADP5588=y
719 Say yes here to enable the adp5588 to be used as an interrupt
720 controller. It requires the driver to be built in the kernel.
723 tristate "Avionic Design N-bit GPIO expander"
724 depends on I2C && OF_GPIO
725 select GPIOLIB_IRQCHIP
727 This option enables support for N GPIOs found on Avionic Design
728 I2C GPIO expanders. The register space will be extended by powers
729 of two, so the controller will need to accommodate for that. For
730 example: if a controller provides 48 pins, 6 registers will be
731 enough to represent all pins, but the driver will assume a
732 register layout for 64 pins (8 registers).
734 comment "PCI GPIO expanders:"
737 tristate "AMD CS5535/CS5536 GPIO support"
738 depends on MFD_CS5535
740 The AMD CS5535 and CS5536 southbridges support 28 GPIO pins that
741 can be used for quite a number of things. The CS5535/6 is found on
742 AMD Geode and Lemote Yeeloong devices.
747 tristate "BT8XX GPIO abuser"
748 depends on PCI && VIDEO_BT848=n
750 The BT8xx frame grabber chip has 24 GPIO pins that can be abused
751 as a cheap PCI GPIO card.
753 This chip can be found on Miro, Hauppauge and STB TV-cards.
755 The card needs to be physically altered for using it as a
756 GPIO card. For more information on how to build a GPIO card
757 from a BT8xx TV card, see the documentation file at
758 Documentation/bt8xxgpio.txt
763 tristate "AMD 8111 GPIO driver"
766 The AMD 8111 south bridge contains 32 GPIO pins which can be used.
768 Note, that usually system firmware/ACPI handles GPIO pins on their
769 own and users might easily break their systems with uncarefull usage
774 config GPIO_INTEL_MID
775 bool "Intel Mid GPIO support"
776 depends on PCI && X86
777 select GPIOLIB_IRQCHIP
779 Say Y here to support Intel Mid GPIO.
782 tristate "Intel EG20T PCH/LAPIS Semiconductor IOH(ML7223/ML7831) GPIO"
783 depends on PCI && (X86_32 || COMPILE_TEST)
784 select GENERIC_IRQ_CHIP
786 This driver is for PCH(Platform controller Hub) GPIO of Intel Topcliff
787 which is an IOH(Input/Output Hub) for x86 embedded processor.
788 This driver can access PCH GPIO device.
790 This driver also can be used for LAPIS Semiconductor IOH(Input/
791 Output Hub), ML7223 and ML7831.
792 ML7223 IOH is for MP(Media Phone) use.
793 ML7831 IOH is for general purpose use.
794 ML7223/ML7831 is companion chip for Intel Atom E6xx series.
795 ML7223/ML7831 is completely compatible for Intel EG20T PCH.
798 tristate "OKI SEMICONDUCTOR ML7213 IOH GPIO support"
800 select GENERIC_IRQ_CHIP
802 ML7213 is companion chip for Intel Atom E6xx series.
803 This driver can be used for OKI SEMICONDUCTOR ML7213 IOH(Input/Output
804 Hub) which is for IVI(In-Vehicle Infotainment) use.
805 This driver can access the IOH's GPIO device.
807 config GPIO_SODAVILLE
808 bool "Intel Sodaville GPIO support"
809 depends on X86 && PCI && OF
811 select GENERIC_IRQ_CHIP
813 Say Y here to support Intel Sodaville GPIO.
815 config GPIO_TIMBERDALE
816 bool "Support for timberdale GPIO IP"
817 depends on MFD_TIMBERDALE
819 Add support for the GPIO IP in the timberdale FPGA.
822 tristate "RDC R-321x GPIO support"
827 Support for the RDC R321x SoC GPIOs over southbridge
828 PCI configuration space.
830 comment "SPI GPIO expanders:"
833 tristate "Maxim MAX7301 GPIO expander"
834 depends on SPI_MASTER
837 GPIO driver for Maxim MAX7301 SPI-based GPIO expander.
840 tristate "Microchip MCP23xxx I/O expander"
841 depends on (SPI_MASTER && !I2C) || I2C
843 SPI/I2C driver for Microchip MCP23S08/MCP23S17/MCP23008/MCP23017
845 This provides a GPIO interface supporting inputs and outputs.
846 The I2C versions of the chips can be used as interrupt-controller.
849 tristate "Freescale MC33880 high-side/low-side switch"
850 depends on SPI_MASTER
852 SPI driver for Freescale MC33880 high-side/low-side switch.
853 This provides GPIO interface supporting inputs and outputs.
856 tristate "74x164 serial-in/parallel-out 8-bits shift register"
857 depends on SPI_MASTER && OF
859 Driver for 74x164 compatible serial-in/parallel-out 8-outputs
860 shift registers. This driver can be used to provide access
861 to more gpio outputs.
863 comment "AC97 GPIO expanders:"
866 tristate "Philips UCB1400 GPIO"
867 depends on UCB1400_CORE
869 This enables support for the Philips UCB1400 GPIO pins.
870 The UCB1400 is an AC97 audio codec.
872 comment "LPC GPIO expanders:"
875 tristate "Kontron ETX / COMexpress GPIO"
876 depends on MFD_KEMPLD
878 This enables support for the PLD GPIO interface on some Kontron ETX
879 and COMexpress (ETXexpress) modules.
881 This driver can also be built as a module. If so, the module will be
884 comment "MODULbus GPIO expanders:"
887 tristate "Janz VMOD-TTL Digital IO Module"
888 depends on MFD_JANZ_CMODIO
890 This enables support for the Janz VMOD-TTL Digital IO module.
891 This driver provides support for driving the pins in output
892 mode only. Input mode is not supported.
895 bool "TI PALMAS series PMICs GPIO"
896 depends on MFD_PALMAS
898 Select this option to enable GPIO driver for the TI PALMAS
903 depends on MFD_TPS6586X
905 Select this option to enable GPIO driver for the TPS6586X
910 depends on MFD_TPS65910
912 Select this option to enable GPIO driver for the TPS65910
916 bool "Intel MSIC mixed signal gpio support"
917 depends on MFD_INTEL_MSIC
919 Enable support for GPIO on intel MSIC controllers found in
923 bool "Broadcom Kona GPIO"
924 depends on OF_GPIO && (ARCH_BCM_MOBILE || COMPILE_TEST)
926 Turn on GPIO support for Broadcom "Kona" chips.
928 comment "USB GPIO expanders:"
930 config GPIO_VIPERBOARD
931 tristate "Viperboard GPIO a & b support"
932 depends on MFD_VIPERBOARD && USB
934 Say yes here to access the GPIO signals of Nano River
935 Technologies Viperboard. There are two GPIO chips on the
936 board: gpioa and gpiob.
937 See viperboard API specification and Nano
938 River Tech's viperboard.h for detailed meaning
939 of the module parameters.
942 tristate "Diolan DLN2 GPIO support"
944 select GPIOLIB_IRQCHIP
947 Select this option to enable GPIO driver for the Diolan DLN2
950 This driver can also be built as a module. If so, the module
951 will be called gpio-dln2.