[deliverable/linux.git] / drivers / ide / pci / siimage.c

/*
 * Copyright (C) 2001-2002      Andre Hedrick <andre@linux-ide.org>
 * Copyright (C) 2003           Red Hat <alan@redhat.com>
 * Copyright (C) 2007-2008      MontaVista Software, Inc.
 * Copyright (C) 2007-2008      Bartlomiej Zolnierkiewicz
 *
 *  May be copied or modified under the terms of the GNU General Public License
 *
 *  Documentation for CMD680:
 *  http://gkernel.sourceforge.net/specs/sii/sii-0680a-v1.31.pdf.bz2
 *
 *  Documentation for SiI 3112:
 *  http://gkernel.sourceforge.net/specs/sii/3112A_SiI-DS-0095-B2.pdf.bz2
 *
 *  Errata and other documentation only available under NDA.
 *
 *
 *  FAQ Items:
 *      If you are using Marvell SATA-IDE adapters with Maxtor drives
 *      ensure the system is set up for ATA100/UDMA5, not UDMA6.
 *
 *      If you are using WD drives with SATA bridges you must set the
 *      drive to "Single". "Master" will hang.
 *
 *      If you have strange problems with nVidia chipset systems please
 *      see the SI support documentation and update your system BIOS
 *      if necessary
 *
 *  The Dell DRAC4 has some interesting features including effectively hot
 *  unplugging/replugging the virtual CD interface when the DRAC is reset.
 *  This often causes drivers/ide/siimage to panic but is ok with the rather
 *  smarter code in libata.
 *
 * TODO:
 * - IORDY fixes
 * - VDMA support
 */

#include <linux/types.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/hdreg.h>
#include <linux/ide.h>
#include <linux/init.h>
#include <linux/io.h>

/**
 *      pdev_is_sata            -       check if device is SATA
 *      @pdev:  PCI device to check
 *
 *      Returns true if this is a SATA controller
 */

static int pdev_is_sata(struct pci_dev *pdev)
{
#ifdef CONFIG_BLK_DEV_IDE_SATA
        switch (pdev->device) {
        case PCI_DEVICE_ID_SII_3112:
        case PCI_DEVICE_ID_SII_1210SA:
                return 1;
        case PCI_DEVICE_ID_SII_680:
                return 0;
        }
        BUG();
#endif
        return 0;
}

/**
 *      is_sata                 -       check if hwif is SATA
 *      @hwif:  interface to check
 *
 *      Returns true if this is a SATA controller
 */

static inline int is_sata(ide_hwif_t *hwif)
{
        return pdev_is_sata(to_pci_dev(hwif->dev));
}

/**
 *      siimage_selreg          -       return register base
 *      @hwif: interface
 *      @r: config offset
 *
 *      Turn a config register offset into the right address in either
 *      PCI space or MMIO space to access the control register in question
 *      Thankfully this is a configuration operation, so isn't performance
 *      critical.
 */

static unsigned long siimage_selreg(ide_hwif_t *hwif, int r)
{
        unsigned long base = (unsigned long)hwif->hwif_data;

        base += 0xA0 + r;
        if (hwif->mmio)
                base += hwif->channel << 6;
        else
                base += hwif->channel << 4;
        return base;
}

/**
 *      siimage_seldev          -       return register base
 *      @hwif: interface
 *      @r: config offset
 *
 *      Turn a config register offset into the right address in either
 *      PCI space or MMIO space to access the control register in question
 *      including accounting for the unit shift.
 */

static inline unsigned long siimage_seldev(ide_drive_t *drive, int r)
{
        ide_hwif_t *hwif        = HWIF(drive);
        unsigned long base      = (unsigned long)hwif->hwif_data;

        base += 0xA0 + r;
        if (hwif->mmio)
                base += hwif->channel << 6;
        else
                base += hwif->channel << 4;
        base |= drive->select.b.unit << drive->select.b.unit;
        return base;
}

static u8 sil_ioread8(struct pci_dev *dev, unsigned long addr)
{
        u8 tmp = 0;

        if (pci_get_drvdata(dev))
                tmp = readb((void __iomem *)addr);
        else
                pci_read_config_byte(dev, addr, &tmp);

        return tmp;
}

static u16 sil_ioread16(struct pci_dev *dev, unsigned long addr)
{
        u16 tmp = 0;

        if (pci_get_drvdata(dev))
                tmp = readw((void __iomem *)addr);
        else
                pci_read_config_word(dev, addr, &tmp);

        return tmp;
}

static void sil_iowrite8(struct pci_dev *dev, u8 val, unsigned long addr)
{
        if (pci_get_drvdata(dev))
                writeb(val, (void __iomem *)addr);
        else
                pci_write_config_byte(dev, addr, val);
}

static void sil_iowrite16(struct pci_dev *dev, u16 val, unsigned long addr)
{
        if (pci_get_drvdata(dev))
                writew(val, (void __iomem *)addr);
        else
                pci_write_config_word(dev, addr, val);
}

static void sil_iowrite32(struct pci_dev *dev, u32 val, unsigned long addr)
{
        if (pci_get_drvdata(dev))
                writel(val, (void __iomem *)addr);
        else
                pci_write_config_dword(dev, addr, val);
}

/**
 *      sil_udma_filter         -       compute UDMA mask
 *      @drive: IDE device
 *
 *      Compute the available UDMA speeds for the device on the interface.
 *
 *      For the CMD680 this depends on the clocking mode (scsc), for the
 *      SI3112 SATA controller life is a bit simpler.
 */

static u8 sil_pata_udma_filter(ide_drive_t *drive)
{
        ide_hwif_t *hwif        = drive->hwif;
        struct pci_dev *dev     = to_pci_dev(hwif->dev);
        unsigned long base      = (unsigned long)hwif->hwif_data;
        u8 scsc, mask           = 0;

        scsc = sil_ioread8(dev, base + (hwif->mmio ? 0x4A : 0x8A));

        switch (scsc & 0x30) {
        case 0x10:      /* 133 */
                mask = ATA_UDMA6;
                break;
        case 0x20:      /* 2xPCI */
                mask = ATA_UDMA6;
                break;
        case 0x00:      /* 100 */
                mask = ATA_UDMA5;
                break;
        default:        /* Disabled ? */
                BUG();
        }

        return mask;
}

static u8 sil_sata_udma_filter(ide_drive_t *drive)
{
        return strstr(drive->id->model, "Maxtor") ? ATA_UDMA5 : ATA_UDMA6;
}

/**
 *      sil_set_pio_mode        -       set host controller for PIO mode
 *      @drive: drive
 *      @pio: PIO mode number
 *
 *      Load the timing settings for this device mode into the
 *      controller. If we are in PIO mode 3 or 4 turn on IORDY
 *      monitoring (bit 9). The TF timing is bits 31:16
 */

static void sil_set_pio_mode(ide_drive_t *drive, u8 pio)
{
        static const u16 tf_speed[]   = { 0x328a, 0x2283, 0x1281, 0x10c3, 0x10c1 };
        static const u16 data_speed[] = { 0x328a, 0x2283, 0x1104, 0x10c3, 0x10c1 };

        ide_hwif_t *hwif        = HWIF(drive);
        struct pci_dev *dev     = to_pci_dev(hwif->dev);
        ide_drive_t *pair       = ide_get_paired_drive(drive);
        u32 speedt              = 0;
        u16 speedp              = 0;
        unsigned long addr      = siimage_seldev(drive, 0x04);
        unsigned long tfaddr    = siimage_selreg(hwif,  0x02);
        unsigned long base      = (unsigned long)hwif->hwif_data;
        u8 tf_pio               = pio;
        u8 addr_mask            = hwif->channel ? (hwif->mmio ? 0xF4 : 0x84)
                                                : (hwif->mmio ? 0xB4 : 0x80);
        u8 mode                 = 0;
        u8 unit                 = drive->select.b.unit;

        /* trim *taskfile* PIO to the slowest of the master/slave */
        if (pair->present) {
                u8 pair_pio = ide_get_best_pio_mode(pair, 255, 4);

                if (pair_pio < tf_pio)
                        tf_pio = pair_pio;
        }

        /* cheat for now and use the docs */
        speedp = data_speed[pio];
        speedt = tf_speed[tf_pio];

        sil_iowrite16(dev, speedp, addr);
        sil_iowrite16(dev, speedt, tfaddr);

        /* now set up IORDY */
        speedp = sil_ioread16(dev, tfaddr - 2);
        speedp &= ~0x200;
        if (pio > 2)
                speedp |= 0x200;
        sil_iowrite16(dev, speedp, tfaddr - 2);

        mode = sil_ioread8(dev, base + addr_mask);
        mode &= ~(unit ? 0x30 : 0x03);
        mode |= unit ? 0x10 : 0x01;
        sil_iowrite8(dev, mode, base + addr_mask);
}

/**
 *      sil_set_dma_mode        -       set host controller for DMA mode
 *      @drive: drive
 *      @speed: DMA mode
 *
 *      Tune the SiI chipset for the desired DMA mode.
 */

static void sil_set_dma_mode(ide_drive_t *drive, const u8 speed)
{
        static const u8 ultra6[] = { 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 };
        static const u8 ultra5[] = { 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01 };
        static const u16 dma[]   = { 0x2208, 0x10C2, 0x10C1 };

        ide_hwif_t *hwif        = HWIF(drive);
        struct pci_dev *dev     = to_pci_dev(hwif->dev);
        u16 ultra = 0, multi    = 0;
        u8 mode = 0, unit       = drive->select.b.unit;
        unsigned long base      = (unsigned long)hwif->hwif_data;
        u8 scsc = 0, addr_mask  = hwif->channel ?
                                        (hwif->mmio ? 0xF4 : 0x84) :
                                        (hwif->mmio ? 0xB4 : 0x80);
        unsigned long ma        = siimage_seldev(drive, 0x08);
        unsigned long ua        = siimage_seldev(drive, 0x0C);

        scsc  = sil_ioread8 (dev, base + (hwif->mmio ? 0x4A : 0x8A));
        mode  = sil_ioread8 (dev, base + addr_mask);
        multi = sil_ioread16(dev, ma);
        ultra = sil_ioread16(dev, ua);

        mode  &= ~(unit ? 0x30 : 0x03);
        ultra &= ~0x3F;
        scsc = ((scsc & 0x30) == 0x00) ? 0 : 1;

        scsc = is_sata(hwif) ? 1 : scsc;

        if (speed >= XFER_UDMA_0) {
                multi  = dma[2];
                ultra |= scsc ? ultra6[speed - XFER_UDMA_0] :
                                ultra5[speed - XFER_UDMA_0];
                mode  |= unit ? 0x30 : 0x03;
        } else {
                multi = dma[speed - XFER_MW_DMA_0];
                mode |= unit ? 0x20 : 0x02;
        }

        sil_iowrite8 (dev, mode, base + addr_mask);
        sil_iowrite16(dev, multi, ma);
        sil_iowrite16(dev, ultra, ua);
}

/* returns 1 if dma irq issued, 0 otherwise */
static int siimage_io_dma_test_irq(ide_drive_t *drive)
{
        ide_hwif_t *hwif        = HWIF(drive);
        struct pci_dev *dev     = to_pci_dev(hwif->dev);
        u8 dma_altstat          = 0;
        unsigned long addr      = siimage_selreg(hwif, 1);

        /* return 1 if INTR asserted */
        if (hwif->INB(hwif->dma_status) & 4)
                return 1;

        /* return 1 if Device INTR asserted */
        pci_read_config_byte(dev, addr, &dma_altstat);
        if (dma_altstat & 8)
                return 0;       /* return 1; */

        return 0;
}

/**
 *      siimage_mmio_dma_test_irq       -       check we caused an IRQ
 *      @drive: drive we are testing
 *
 *      Check if we caused an IDE DMA interrupt. We may also have caused
 *      SATA status interrupts, if so we clean them up and continue.
 */

static int siimage_mmio_dma_test_irq(ide_drive_t *drive)
{
        ide_hwif_t *hwif        = HWIF(drive);
        unsigned long addr      = siimage_selreg(hwif, 0x1);
        void __iomem *sata_error_addr
                = (void __iomem *)hwif->sata_scr[SATA_ERROR_OFFSET];

        if (sata_error_addr) {
                unsigned long base      = (unsigned long)hwif->hwif_data;
                u32 ext_stat            = readl((void __iomem *)(base + 0x10));
                u8 watchdog             = 0;

                if (ext_stat & ((hwif->channel) ? 0x40 : 0x10)) {
                        u32 sata_error = readl(sata_error_addr);

                        writel(sata_error, sata_error_addr);
                        watchdog = (sata_error & 0x00680000) ? 1 : 0;
                        printk(KERN_WARNING "%s: sata_error = 0x%08x, "
                                "watchdog = %d, %s\n",
                                drive->name, sata_error, watchdog, __func__);
                } else
                        watchdog = (ext_stat & 0x8000) ? 1 : 0;

                ext_stat >>= 16;
                if (!(ext_stat & 0x0404) && !watchdog)
                        return 0;
        }

        /* return 1 if INTR asserted */
        if (readb((void __iomem *)hwif->dma_status) & 0x04)
                return 1;

        /* return 1 if Device INTR asserted */
        if (readb((void __iomem *)addr) & 8)
                return 0;       /* return 1; */

        return 0;
}

static int siimage_dma_test_irq(ide_drive_t *drive)
{
        if (drive->hwif->mmio)
                return siimage_mmio_dma_test_irq(drive);
        else
                return siimage_io_dma_test_irq(drive);
}

/**
 *      sil_sata_reset_poll     -       wait for SATA reset
 *      @drive: drive we are resetting
 *
 *      Poll the SATA phy and see whether it has come back from the dead
 *      yet.
 */

static int sil_sata_reset_poll(ide_drive_t *drive)
{
        ide_hwif_t *hwif = drive->hwif;
        void __iomem *sata_status_addr
                = (void __iomem *)hwif->sata_scr[SATA_STATUS_OFFSET];

        if (sata_status_addr) {
                /* SATA Status is available only when in MMIO mode */
                u32 sata_stat = readl(sata_status_addr);

                if ((sata_stat & 0x03) != 0x03) {
                        printk(KERN_WARNING "%s: reset phy dead, status=0x%08x\n",
                                            hwif->name, sata_stat);
                        HWGROUP(drive)->polling = 0;
                        return ide_started;
                }
        }

        return 0;
}

/**
 *      sil_sata_pre_reset      -       reset hook
 *      @drive: IDE device being reset
 *
 *      For the SATA devices we need to handle recalibration/geometry
 *      differently
 */

static void sil_sata_pre_reset(ide_drive_t *drive)
{
        if (drive->media == ide_disk) {
                drive->special.b.set_geometry = 0;
                drive->special.b.recalibrate = 0;
        }
}

/**
 *      setup_mmio_siimage      -       switch controller into MMIO mode
 *      @dev: PCI device we are configuring
 *      @name: device name
 *
 *      Attempt to put the device into MMIO mode. There are some slight
 *      complications here with certain systems where the MMIO BAR isn't
 *      mapped, so we have to be sure that we can fall back to I/O.
 */

static unsigned int setup_mmio_siimage(struct pci_dev *dev, const char *name)
{
        resource_size_t bar5    = pci_resource_start(dev, 5);
        unsigned long barsize   = pci_resource_len(dev, 5);
        void __iomem *ioaddr;

        /*
         *      Drop back to PIO if we can't map the MMIO. Some systems
         *      seem to get terminally confused in the PCI spaces.
         */
        if (!request_mem_region(bar5, barsize, name)) {
                printk(KERN_WARNING "siimage: IDE controller MMIO ports not "
                                    "available.\n");
                return 0;
        }

        ioaddr = ioremap(bar5, barsize);
        if (ioaddr == NULL) {
                release_mem_region(bar5, barsize);
                return 0;
        }

        pci_set_master(dev);
        pci_set_drvdata(dev, (void *) ioaddr);

        return 1;
}

/**
 *      init_chipset_siimage    -       set up an SI device
 *      @dev: PCI device
 *      @name: device name
 *
 *      Perform the initial PCI set up for this device. Attempt to switch
 *      to 133 MHz clocking if the system isn't already set up to do it.
 */

static unsigned int __devinit init_chipset_siimage(struct pci_dev *dev,
                                                   const char *name)
{
        unsigned long base, scsc_addr;
        void __iomem *ioaddr = NULL;
        u8 rev = dev->revision, tmp, BA5_EN;

        pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, rev ? 1 : 255);

        pci_read_config_byte(dev, 0x8A, &BA5_EN);

        if ((BA5_EN & 0x01) || pci_resource_start(dev, 5))
                if (setup_mmio_siimage(dev, name))
                        ioaddr = pci_get_drvdata(dev);

        base = (unsigned long)ioaddr;

        if (ioaddr && pdev_is_sata(dev)) {
                u32 tmp32, irq_mask;

                /* make sure IDE0/1 interrupts are not masked */
                irq_mask = (1 << 22) | (1 << 23);
                tmp32 = readl(ioaddr + 0x48);
                if (tmp32 & irq_mask) {
                        tmp32 &= ~irq_mask;
                        writel(tmp32, ioaddr + 0x48);
                        readl(ioaddr + 0x48); /* flush */
                }
                writel(0, ioaddr + 0x148);
                writel(0, ioaddr + 0x1C8);
        }

        sil_iowrite8(dev, 0, base ? (base + 0xB4) : 0x80);
        sil_iowrite8(dev, 0, base ? (base + 0xF4) : 0x84);

        scsc_addr = base ? (base + 0x4A) : 0x8A;
        tmp = sil_ioread8(dev, scsc_addr);

        switch (tmp & 0x30) {
        case 0x00:
                /* On 100 MHz clocking, try and switch to 133 MHz */
                sil_iowrite8(dev, tmp | 0x10, scsc_addr);
                break;
        case 0x30:
                /* Clocking is disabled, attempt to force 133MHz clocking. */
                sil_iowrite8(dev, tmp & ~0x20, scsc_addr);
        case 0x10:
                /* On 133Mhz clocking. */
                break;
        case 0x20:
                /* On PCIx2 clocking. */
                break;
        }

        tmp = sil_ioread8(dev, scsc_addr);

        sil_iowrite8 (dev,       0x72, base + 0xA1);
        sil_iowrite16(dev,     0x328A, base + 0xA2);
        sil_iowrite32(dev, 0x62DD62DD, base + 0xA4);
        sil_iowrite32(dev, 0x43924392, base + 0xA8);
        sil_iowrite32(dev, 0x40094009, base + 0xAC);
        sil_iowrite8 (dev,       0x72, base ? (base + 0xE1) : 0xB1);
        sil_iowrite16(dev,     0x328A, base ? (base + 0xE2) : 0xB2);
        sil_iowrite32(dev, 0x62DD62DD, base ? (base + 0xE4) : 0xB4);
        sil_iowrite32(dev, 0x43924392, base ? (base + 0xE8) : 0xB8);
        sil_iowrite32(dev, 0x40094009, base ? (base + 0xEC) : 0xBC);

        if (base && pdev_is_sata(dev)) {
                writel(0xFFFF0000, ioaddr + 0x108);
                writel(0xFFFF0000, ioaddr + 0x188);
                writel(0x00680000, ioaddr + 0x148);
                writel(0x00680000, ioaddr + 0x1C8);
        }

        /* report the clocking mode of the controller */
        if (!pdev_is_sata(dev)) {
                static const char *clk_str[] =
                        { "== 100", "== 133", "== 2X PCI", "DISABLED!" };

                tmp >>= 4;
                printk(KERN_INFO "%s: BASE CLOCK %s\n", name, clk_str[tmp & 3]);
        }

        return 0;
}

/**
 *      init_mmio_iops_siimage  -       set up the iops for MMIO
 *      @hwif: interface to set up
 *
 *      The basic setup here is fairly simple, we can use standard MMIO
 *      operations. However we do have to set the taskfile register offsets
 *      by hand as there isn't a standard defined layout for them this time.
 *
 *      The hardware supports buffered taskfiles and also some rather nice
 *      extended PRD tables. For better SI3112 support use the libata driver
 */

static void __devinit init_mmio_iops_siimage(ide_hwif_t *hwif)
{
        struct pci_dev *dev     = to_pci_dev(hwif->dev);
        void *addr              = pci_get_drvdata(dev);
        u8 ch                   = hwif->channel;
        struct ide_io_ports *io_ports = &hwif->io_ports;
        unsigned long base;

        /*
         *      Fill in the basic hwif bits
         */
        hwif->host_flags |= IDE_HFLAG_MMIO;
        default_hwif_mmiops(hwif);
        hwif->hwif_data = addr;

        /*
         *      Now set up the hw. We have to do this ourselves as the
         *      MMIO layout isn't the same as the standard port based I/O.
         */
        memset(io_ports, 0, sizeof(*io_ports));

        base = (unsigned long)addr;
        if (ch)
                base += 0xC0;
        else
                base += 0x80;

        /*
         *      The buffered task file doesn't have status/control, so we
         *      can't currently use it sanely since we want to use LBA48 mode.
         */
        io_ports->data_addr     = base;
        io_ports->error_addr    = base + 1;
        io_ports->nsect_addr    = base + 2;
        io_ports->lbal_addr     = base + 3;
        io_ports->lbam_addr     = base + 4;
        io_ports->lbah_addr     = base + 5;
        io_ports->device_addr   = base + 6;
        io_ports->status_addr   = base + 7;
        io_ports->ctl_addr      = base + 10;

        if (pdev_is_sata(dev)) {
                base = (unsigned long)addr;
                if (ch)
                        base += 0x80;
                hwif->sata_scr[SATA_STATUS_OFFSET]      = base + 0x104;
                hwif->sata_scr[SATA_ERROR_OFFSET]       = base + 0x108;
                hwif->sata_scr[SATA_CONTROL_OFFSET]     = base + 0x100;
        }

        hwif->irq = dev->irq;

        hwif->dma_base = (unsigned long)addr + (ch ? 0x08 : 0x00);

        hwif->mmio = 1;
}

static int is_dev_seagate_sata(ide_drive_t *drive)
{
        const char *s   = &drive->id->model[0];
        unsigned len    = strnlen(s, sizeof(drive->id->model));

        if ((len > 4) && (!memcmp(s, "ST", 2)))
                if ((!memcmp(s + len - 2, "AS", 2)) ||
                    (!memcmp(s + len - 3, "ASL", 3))) {
                        printk(KERN_INFO "%s: applying pessimistic Seagate "
                                         "errata fix\n", drive->name);
                        return 1;
                }

        return 0;
}

/**
 *      sil_quirkproc           -       post probe fixups
 *      @drive: drive
 *
 *      Called after drive probe we use this to decide whether the
 *      Seagate fixup must be applied. This used to be in init_iops but
 *      that can occur before we know what drives are present.
 */

static void __devinit sil_quirkproc(ide_drive_t *drive)
{
        ide_hwif_t *hwif = drive->hwif;

        /* Try and rise the rqsize */
        if (!is_sata(hwif) || !is_dev_seagate_sata(drive))
                hwif->rqsize = 128;
}

/**
 *      init_iops_siimage       -       set up iops
 *      @hwif: interface to set up
 *
 *      Do the basic setup for the SIIMAGE hardware interface
 *      and then do the MMIO setup if we can. This is the first
 *      look in we get for setting up the hwif so that we
 *      can get the iops right before using them.
 */

static void __devinit init_iops_siimage(ide_hwif_t *hwif)
{
        struct pci_dev *dev = to_pci_dev(hwif->dev);

        hwif->hwif_data = NULL;

        /* Pessimal until we finish probing */
        hwif->rqsize = 15;

        if (pci_get_drvdata(dev) == NULL)
                return;

        init_mmio_iops_siimage(hwif);
}

/**
 *      sil_cable_detect        -       cable detection
 *      @hwif: interface to check
 *
 *      Check for the presence of an ATA66 capable cable on the interface.
 */

static u8 __devinit sil_cable_detect(ide_hwif_t *hwif)
{
        struct pci_dev *dev     = to_pci_dev(hwif->dev);
        unsigned long addr      = siimage_selreg(hwif, 0);
        u8 ata66                = sil_ioread8(dev, addr);

        return (ata66 & 0x01) ? ATA_CBL_PATA80 : ATA_CBL_PATA40;
}

static const struct ide_port_ops sil_pata_port_ops = {
        .set_pio_mode           = sil_set_pio_mode,
        .set_dma_mode           = sil_set_dma_mode,
        .quirkproc              = sil_quirkproc,
        .udma_filter            = sil_pata_udma_filter,
        .cable_detect           = sil_cable_detect,
};

static const struct ide_port_ops sil_sata_port_ops = {
        .set_pio_mode           = sil_set_pio_mode,
        .set_dma_mode           = sil_set_dma_mode,
        .reset_poll             = sil_sata_reset_poll,
        .pre_reset              = sil_sata_pre_reset,
        .quirkproc              = sil_quirkproc,
        .udma_filter            = sil_sata_udma_filter,
        .cable_detect           = sil_cable_detect,
};

static struct ide_dma_ops sil_dma_ops = {
        .dma_test_irq           = siimage_dma_test_irq,
};

#define DECLARE_SII_DEV(name_str, p_ops)                \
        {                                               \
                .name           = name_str,             \
                .init_chipset   = init_chipset_siimage, \
                .init_iops      = init_iops_siimage,    \
                .port_ops       = p_ops,                \
                .dma_ops        = &sil_dma_ops,         \
                .pio_mask       = ATA_PIO4,             \
                .mwdma_mask     = ATA_MWDMA2,           \
                .udma_mask      = ATA_UDMA6,            \
        }

static const struct ide_port_info siimage_chipsets[] __devinitdata = {
        /* 0 */ DECLARE_SII_DEV("SiI680",               &sil_pata_port_ops),
        /* 1 */ DECLARE_SII_DEV("SiI3112 Serial ATA",   &sil_sata_port_ops),
        /* 2 */ DECLARE_SII_DEV("Adaptec AAR-1210SA",   &sil_sata_port_ops)
};

/**
 *      siimage_init_one        -       PCI layer discovery entry
 *      @dev: PCI device
 *      @id: ident table entry
 *
 *      Called by the PCI code when it finds an SiI680 or SiI3112 controller.
 *      We then use the IDE PCI generic helper to do most of the work.
 */

static int __devinit siimage_init_one(struct pci_dev *dev,
                                      const struct pci_device_id *id)
{
        struct ide_port_info d;
        u8 idx = id->driver_data;

        d = siimage_chipsets[idx];

        if (idx) {
                static int first = 1;

                if (first) {
                        printk(KERN_INFO "siimage: For full SATA support you "
                                "should use the libata sata_sil module.\n");
                        first = 0;
                }

                d.host_flags |= IDE_HFLAG_NO_ATAPI_DMA;
        }

        return ide_setup_pci_device(dev, &d);
}

static const struct pci_device_id siimage_pci_tbl[] = {
        { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_680),    0 },
#ifdef CONFIG_BLK_DEV_IDE_SATA
        { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_3112),   1 },
        { PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_1210SA), 2 },
#endif
        { 0, },
};
MODULE_DEVICE_TABLE(pci, siimage_pci_tbl);

static struct pci_driver driver = {
        .name           = "SiI_IDE",
        .id_table       = siimage_pci_tbl,
        .probe          = siimage_init_one,
};

static int __init siimage_ide_init(void)
{
        return ide_pci_register_driver(&driver);
}

module_init(siimage_ide_init);

MODULE_AUTHOR("Andre Hedrick, Alan Cox");
MODULE_DESCRIPTION("PCI driver module for SiI IDE");
MODULE_LICENSE("GPL");