IB/qib: Remove ibport and use rdmavt version

[deliverable/linux.git] / drivers / infiniband / hw / qib / qib_iba6120.c

/*
 * Copyright (c) 2013 Intel Corporation. All rights reserved.
 * Copyright (c) 2006, 2007, 2008, 2009, 2010 QLogic Corporation.
 * All rights reserved.
 * Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
 *
 * This software is available to you under a choice of one of two
 * licenses.  You may choose to be licensed under the terms of the GNU
 * General Public License (GPL) Version 2, available from the file
 * COPYING in the main directory of this source tree, or the
 * OpenIB.org BSD license below:
 *
 *     Redistribution and use in source and binary forms, with or
 *     without modification, are permitted provided that the following
 *     conditions are met:
 *
 *      - Redistributions of source code must retain the above
 *        copyright notice, this list of conditions and the following
 *        disclaimer.
 *
 *      - Redistributions in binary form must reproduce the above
 *        copyright notice, this list of conditions and the following
 *        disclaimer in the documentation and/or other materials
 *        provided with the distribution.
 *
 * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
 * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
 * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS
 * BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN
 * ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN
 * CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
 * SOFTWARE.
 */
/*
 * This file contains all of the code that is specific to the
 * QLogic_IB 6120 PCIe chip.
 */

#include <linux/interrupt.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <rdma/ib_verbs.h>

#include "qib.h"
#include "qib_6120_regs.h"

static void qib_6120_setup_setextled(struct qib_pportdata *, u32);
static void sendctrl_6120_mod(struct qib_pportdata *ppd, u32 op);
static u8 qib_6120_phys_portstate(u64);
static u32 qib_6120_iblink_state(u64);

/*
 * This file contains all the chip-specific register information and
 * access functions for the Intel Intel_IB PCI-Express chip.
 *
 */

/* KREG_IDX uses machine-generated #defines */
#define KREG_IDX(regname) (QIB_6120_##regname##_OFFS / sizeof(u64))

/* Use defines to tie machine-generated names to lower-case names */
#define kr_extctrl KREG_IDX(EXTCtrl)
#define kr_extstatus KREG_IDX(EXTStatus)
#define kr_gpio_clear KREG_IDX(GPIOClear)
#define kr_gpio_mask KREG_IDX(GPIOMask)
#define kr_gpio_out KREG_IDX(GPIOOut)
#define kr_gpio_status KREG_IDX(GPIOStatus)
#define kr_rcvctrl KREG_IDX(RcvCtrl)
#define kr_sendctrl KREG_IDX(SendCtrl)
#define kr_partitionkey KREG_IDX(RcvPartitionKey)
#define kr_hwdiagctrl KREG_IDX(HwDiagCtrl)
#define kr_ibcstatus KREG_IDX(IBCStatus)
#define kr_ibcctrl KREG_IDX(IBCCtrl)
#define kr_sendbuffererror KREG_IDX(SendBufErr0)
#define kr_rcvbthqp KREG_IDX(RcvBTHQP)
#define kr_counterregbase KREG_IDX(CntrRegBase)
#define kr_palign KREG_IDX(PageAlign)
#define kr_rcvegrbase KREG_IDX(RcvEgrBase)
#define kr_rcvegrcnt KREG_IDX(RcvEgrCnt)
#define kr_rcvhdrcnt KREG_IDX(RcvHdrCnt)
#define kr_rcvhdrentsize KREG_IDX(RcvHdrEntSize)
#define kr_rcvhdrsize KREG_IDX(RcvHdrSize)
#define kr_rcvtidbase KREG_IDX(RcvTIDBase)
#define kr_rcvtidcnt KREG_IDX(RcvTIDCnt)
#define kr_scratch KREG_IDX(Scratch)
#define kr_sendctrl KREG_IDX(SendCtrl)
#define kr_sendpioavailaddr KREG_IDX(SendPIOAvailAddr)
#define kr_sendpiobufbase KREG_IDX(SendPIOBufBase)
#define kr_sendpiobufcnt KREG_IDX(SendPIOBufCnt)
#define kr_sendpiosize KREG_IDX(SendPIOSize)
#define kr_sendregbase KREG_IDX(SendRegBase)
#define kr_userregbase KREG_IDX(UserRegBase)
#define kr_control KREG_IDX(Control)
#define kr_intclear KREG_IDX(IntClear)
#define kr_intmask KREG_IDX(IntMask)
#define kr_intstatus KREG_IDX(IntStatus)
#define kr_errclear KREG_IDX(ErrClear)
#define kr_errmask KREG_IDX(ErrMask)
#define kr_errstatus KREG_IDX(ErrStatus)
#define kr_hwerrclear KREG_IDX(HwErrClear)
#define kr_hwerrmask KREG_IDX(HwErrMask)
#define kr_hwerrstatus KREG_IDX(HwErrStatus)
#define kr_revision KREG_IDX(Revision)
#define kr_portcnt KREG_IDX(PortCnt)
#define kr_serdes_cfg0 KREG_IDX(SerdesCfg0)
#define kr_serdes_cfg1 (kr_serdes_cfg0 + 1)
#define kr_serdes_stat KREG_IDX(SerdesStat)
#define kr_xgxs_cfg KREG_IDX(XGXSCfg)

/* These must only be written via qib_write_kreg_ctxt() */
#define kr_rcvhdraddr KREG_IDX(RcvHdrAddr0)
#define kr_rcvhdrtailaddr KREG_IDX(RcvHdrTailAddr0)

#define CREG_IDX(regname) ((QIB_6120_##regname##_OFFS - \
                        QIB_6120_LBIntCnt_OFFS) / sizeof(u64))

#define cr_badformat CREG_IDX(RxBadFormatCnt)
#define cr_erricrc CREG_IDX(RxICRCErrCnt)
#define cr_errlink CREG_IDX(RxLinkProblemCnt)
#define cr_errlpcrc CREG_IDX(RxLPCRCErrCnt)
#define cr_errpkey CREG_IDX(RxPKeyMismatchCnt)
#define cr_rcvflowctrl_err CREG_IDX(RxFlowCtrlErrCnt)
#define cr_err_rlen CREG_IDX(RxLenErrCnt)
#define cr_errslen CREG_IDX(TxLenErrCnt)
#define cr_errtidfull CREG_IDX(RxTIDFullErrCnt)
#define cr_errtidvalid CREG_IDX(RxTIDValidErrCnt)
#define cr_errvcrc CREG_IDX(RxVCRCErrCnt)
#define cr_ibstatuschange CREG_IDX(IBStatusChangeCnt)
#define cr_lbint CREG_IDX(LBIntCnt)
#define cr_invalidrlen CREG_IDX(RxMaxMinLenErrCnt)
#define cr_invalidslen CREG_IDX(TxMaxMinLenErrCnt)
#define cr_lbflowstall CREG_IDX(LBFlowStallCnt)
#define cr_pktrcv CREG_IDX(RxDataPktCnt)
#define cr_pktrcvflowctrl CREG_IDX(RxFlowPktCnt)
#define cr_pktsend CREG_IDX(TxDataPktCnt)
#define cr_pktsendflow CREG_IDX(TxFlowPktCnt)
#define cr_portovfl CREG_IDX(RxP0HdrEgrOvflCnt)
#define cr_rcvebp CREG_IDX(RxEBPCnt)
#define cr_rcvovfl CREG_IDX(RxBufOvflCnt)
#define cr_senddropped CREG_IDX(TxDroppedPktCnt)
#define cr_sendstall CREG_IDX(TxFlowStallCnt)
#define cr_sendunderrun CREG_IDX(TxUnderrunCnt)
#define cr_wordrcv CREG_IDX(RxDwordCnt)
#define cr_wordsend CREG_IDX(TxDwordCnt)
#define cr_txunsupvl CREG_IDX(TxUnsupVLErrCnt)
#define cr_rxdroppkt CREG_IDX(RxDroppedPktCnt)
#define cr_iblinkerrrecov CREG_IDX(IBLinkErrRecoveryCnt)
#define cr_iblinkdown CREG_IDX(IBLinkDownedCnt)
#define cr_ibsymbolerr CREG_IDX(IBSymbolErrCnt)

#define SYM_RMASK(regname, fldname) ((u64)              \
        QIB_6120_##regname##_##fldname##_RMASK)
#define SYM_MASK(regname, fldname) ((u64)               \
        QIB_6120_##regname##_##fldname##_RMASK <<       \
         QIB_6120_##regname##_##fldname##_LSB)
#define SYM_LSB(regname, fldname) (QIB_6120_##regname##_##fldname##_LSB)

#define SYM_FIELD(value, regname, fldname) ((u64) \
        (((value) >> SYM_LSB(regname, fldname)) & \
         SYM_RMASK(regname, fldname)))
#define ERR_MASK(fldname) SYM_MASK(ErrMask, fldname##Mask)
#define HWE_MASK(fldname) SYM_MASK(HwErrMask, fldname##Mask)

/* link training states, from IBC */
#define IB_6120_LT_STATE_DISABLED        0x00
#define IB_6120_LT_STATE_LINKUP          0x01
#define IB_6120_LT_STATE_POLLACTIVE      0x02
#define IB_6120_LT_STATE_POLLQUIET       0x03
#define IB_6120_LT_STATE_SLEEPDELAY      0x04
#define IB_6120_LT_STATE_SLEEPQUIET      0x05
#define IB_6120_LT_STATE_CFGDEBOUNCE     0x08
#define IB_6120_LT_STATE_CFGRCVFCFG      0x09
#define IB_6120_LT_STATE_CFGWAITRMT      0x0a
#define IB_6120_LT_STATE_CFGIDLE 0x0b
#define IB_6120_LT_STATE_RECOVERRETRAIN  0x0c
#define IB_6120_LT_STATE_RECOVERWAITRMT  0x0e
#define IB_6120_LT_STATE_RECOVERIDLE     0x0f

/* link state machine states from IBC */
#define IB_6120_L_STATE_DOWN             0x0
#define IB_6120_L_STATE_INIT             0x1
#define IB_6120_L_STATE_ARM              0x2
#define IB_6120_L_STATE_ACTIVE           0x3
#define IB_6120_L_STATE_ACT_DEFER        0x4

static const u8 qib_6120_physportstate[0x20] = {
        [IB_6120_LT_STATE_DISABLED] = IB_PHYSPORTSTATE_DISABLED,
        [IB_6120_LT_STATE_LINKUP] = IB_PHYSPORTSTATE_LINKUP,
        [IB_6120_LT_STATE_POLLACTIVE] = IB_PHYSPORTSTATE_POLL,
        [IB_6120_LT_STATE_POLLQUIET] = IB_PHYSPORTSTATE_POLL,
        [IB_6120_LT_STATE_SLEEPDELAY] = IB_PHYSPORTSTATE_SLEEP,
        [IB_6120_LT_STATE_SLEEPQUIET] = IB_PHYSPORTSTATE_SLEEP,
        [IB_6120_LT_STATE_CFGDEBOUNCE] =
                IB_PHYSPORTSTATE_CFG_TRAIN,
        [IB_6120_LT_STATE_CFGRCVFCFG] =
                IB_PHYSPORTSTATE_CFG_TRAIN,
        [IB_6120_LT_STATE_CFGWAITRMT] =
                IB_PHYSPORTSTATE_CFG_TRAIN,
        [IB_6120_LT_STATE_CFGIDLE] = IB_PHYSPORTSTATE_CFG_TRAIN,
        [IB_6120_LT_STATE_RECOVERRETRAIN] =
                IB_PHYSPORTSTATE_LINK_ERR_RECOVER,
        [IB_6120_LT_STATE_RECOVERWAITRMT] =
                IB_PHYSPORTSTATE_LINK_ERR_RECOVER,
        [IB_6120_LT_STATE_RECOVERIDLE] =
                IB_PHYSPORTSTATE_LINK_ERR_RECOVER,
        [0x10] = IB_PHYSPORTSTATE_CFG_TRAIN,
        [0x11] = IB_PHYSPORTSTATE_CFG_TRAIN,
        [0x12] = IB_PHYSPORTSTATE_CFG_TRAIN,
        [0x13] = IB_PHYSPORTSTATE_CFG_TRAIN,
        [0x14] = IB_PHYSPORTSTATE_CFG_TRAIN,
        [0x15] = IB_PHYSPORTSTATE_CFG_TRAIN,
        [0x16] = IB_PHYSPORTSTATE_CFG_TRAIN,
        [0x17] = IB_PHYSPORTSTATE_CFG_TRAIN
};


struct qib_chip_specific {
        u64 __iomem *cregbase;
        u64 *cntrs;
        u64 *portcntrs;
        void *dummy_hdrq;   /* used after ctxt close */
        dma_addr_t dummy_hdrq_phys;
        spinlock_t kernel_tid_lock; /* no back to back kernel TID writes */
        spinlock_t user_tid_lock; /* no back to back user TID writes */
        spinlock_t rcvmod_lock; /* protect rcvctrl shadow changes */
        spinlock_t gpio_lock; /* RMW of shadows/regs for ExtCtrl and GPIO */
        u64 hwerrmask;
        u64 errormask;
        u64 gpio_out; /* shadow of kr_gpio_out, for rmw ops */
        u64 gpio_mask; /* shadow the gpio mask register */
        u64 extctrl; /* shadow the gpio output enable, etc... */
        /*
         * these 5 fields are used to establish deltas for IB symbol
         * errors and linkrecovery errors.  They can be reported on
         * some chips during link negotiation prior to INIT, and with
         * DDR when faking DDR negotiations with non-IBTA switches.
         * The chip counters are adjusted at driver unload if there is
         * a non-zero delta.
         */
        u64 ibdeltainprog;
        u64 ibsymdelta;
        u64 ibsymsnap;
        u64 iblnkerrdelta;
        u64 iblnkerrsnap;
        u64 ibcctrl; /* shadow for kr_ibcctrl */
        u32 lastlinkrecov; /* link recovery issue */
        int irq;
        u32 cntrnamelen;
        u32 portcntrnamelen;
        u32 ncntrs;
        u32 nportcntrs;
        /* used with gpio interrupts to implement IB counters */
        u32 rxfc_unsupvl_errs;
        u32 overrun_thresh_errs;
        /*
         * these count only cases where _successive_ LocalLinkIntegrity
         * errors were seen in the receive headers of IB standard packets
         */
        u32 lli_errs;
        u32 lli_counter;
        u64 lli_thresh;
        u64 sword; /* total dwords sent (sample result) */
        u64 rword; /* total dwords received (sample result) */
        u64 spkts; /* total packets sent (sample result) */
        u64 rpkts; /* total packets received (sample result) */
        u64 xmit_wait; /* # of ticks no data sent (sample result) */
        struct timer_list pma_timer;
        char emsgbuf[128];
        char bitsmsgbuf[64];
        u8 pma_sample_status;
};

/* ibcctrl bits */
#define QLOGIC_IB_IBCC_LINKINITCMD_DISABLE 1
/* cycle through TS1/TS2 till OK */
#define QLOGIC_IB_IBCC_LINKINITCMD_POLL 2
/* wait for TS1, then go on */
#define QLOGIC_IB_IBCC_LINKINITCMD_SLEEP 3
#define QLOGIC_IB_IBCC_LINKINITCMD_SHIFT 16

#define QLOGIC_IB_IBCC_LINKCMD_DOWN 1           /* move to 0x11 */
#define QLOGIC_IB_IBCC_LINKCMD_ARMED 2          /* move to 0x21 */
#define QLOGIC_IB_IBCC_LINKCMD_ACTIVE 3 /* move to 0x31 */
#define QLOGIC_IB_IBCC_LINKCMD_SHIFT 18

/*
 * We could have a single register get/put routine, that takes a group type,
 * but this is somewhat clearer and cleaner.  It also gives us some error
 * checking.  64 bit register reads should always work, but are inefficient
 * on opteron (the northbridge always generates 2 separate HT 32 bit reads),
 * so we use kreg32 wherever possible.  User register and counter register
 * reads are always 32 bit reads, so only one form of those routines.
 */

/**
 * qib_read_ureg32 - read 32-bit virtualized per-context register
 * @dd: device
 * @regno: register number
 * @ctxt: context number
 *
 * Return the contents of a register that is virtualized to be per context.
 * Returns -1 on errors (not distinguishable from valid contents at
 * runtime; we may add a separate error variable at some point).
 */
static inline u32 qib_read_ureg32(const struct qib_devdata *dd,
                                  enum qib_ureg regno, int ctxt)
{
        if (!dd->kregbase || !(dd->flags & QIB_PRESENT))
                return 0;

        if (dd->userbase)
                return readl(regno + (u64 __iomem *)
                             ((char __iomem *)dd->userbase +
                              dd->ureg_align * ctxt));
        else
                return readl(regno + (u64 __iomem *)
                             (dd->uregbase +
                              (char __iomem *)dd->kregbase +
                              dd->ureg_align * ctxt));
}

/**
 * qib_write_ureg - write 32-bit virtualized per-context register
 * @dd: device
 * @regno: register number
 * @value: value
 * @ctxt: context
 *
 * Write the contents of a register that is virtualized to be per context.
 */
static inline void qib_write_ureg(const struct qib_devdata *dd,
                                  enum qib_ureg regno, u64 value, int ctxt)
{
        u64 __iomem *ubase;

        if (dd->userbase)
                ubase = (u64 __iomem *)
                        ((char __iomem *) dd->userbase +
                         dd->ureg_align * ctxt);
        else
                ubase = (u64 __iomem *)
                        (dd->uregbase +
                         (char __iomem *) dd->kregbase +
                         dd->ureg_align * ctxt);

        if (dd->kregbase && (dd->flags & QIB_PRESENT))
                writeq(value, &ubase[regno]);
}

static inline u32 qib_read_kreg32(const struct qib_devdata *dd,
                                  const u16 regno)
{
        if (!dd->kregbase || !(dd->flags & QIB_PRESENT))
                return -1;
        return readl((u32 __iomem *)&dd->kregbase[regno]);
}

static inline u64 qib_read_kreg64(const struct qib_devdata *dd,
                                  const u16 regno)
{
        if (!dd->kregbase || !(dd->flags & QIB_PRESENT))
                return -1;

        return readq(&dd->kregbase[regno]);
}

static inline void qib_write_kreg(const struct qib_devdata *dd,
                                  const u16 regno, u64 value)
{
        if (dd->kregbase && (dd->flags & QIB_PRESENT))
                writeq(value, &dd->kregbase[regno]);
}

/**
 * qib_write_kreg_ctxt - write a device's per-ctxt 64-bit kernel register
 * @dd: the qlogic_ib device
 * @regno: the register number to write
 * @ctxt: the context containing the register
 * @value: the value to write
 */
static inline void qib_write_kreg_ctxt(const struct qib_devdata *dd,
                                       const u16 regno, unsigned ctxt,
                                       u64 value)
{
        qib_write_kreg(dd, regno + ctxt, value);
}

static inline void write_6120_creg(const struct qib_devdata *dd,
                                   u16 regno, u64 value)
{
        if (dd->cspec->cregbase && (dd->flags & QIB_PRESENT))
                writeq(value, &dd->cspec->cregbase[regno]);
}

static inline u64 read_6120_creg(const struct qib_devdata *dd, u16 regno)
{
        if (!dd->cspec->cregbase || !(dd->flags & QIB_PRESENT))
                return 0;
        return readq(&dd->cspec->cregbase[regno]);
}

static inline u32 read_6120_creg32(const struct qib_devdata *dd, u16 regno)
{
        if (!dd->cspec->cregbase || !(dd->flags & QIB_PRESENT))
                return 0;
        return readl(&dd->cspec->cregbase[regno]);
}

/* kr_control bits */
#define QLOGIC_IB_C_RESET 1U

/* kr_intstatus, kr_intclear, kr_intmask bits */
#define QLOGIC_IB_I_RCVURG_MASK ((1U << 5) - 1)
#define QLOGIC_IB_I_RCVURG_SHIFT 0
#define QLOGIC_IB_I_RCVAVAIL_MASK ((1U << 5) - 1)
#define QLOGIC_IB_I_RCVAVAIL_SHIFT 12

#define QLOGIC_IB_C_FREEZEMODE 0x00000002
#define QLOGIC_IB_C_LINKENABLE 0x00000004
#define QLOGIC_IB_I_ERROR               0x0000000080000000ULL
#define QLOGIC_IB_I_SPIOSENT            0x0000000040000000ULL
#define QLOGIC_IB_I_SPIOBUFAVAIL        0x0000000020000000ULL
#define QLOGIC_IB_I_GPIO                0x0000000010000000ULL
#define QLOGIC_IB_I_BITSEXTANT \
                ((QLOGIC_IB_I_RCVURG_MASK << QLOGIC_IB_I_RCVURG_SHIFT) | \
                (QLOGIC_IB_I_RCVAVAIL_MASK << \
                 QLOGIC_IB_I_RCVAVAIL_SHIFT) | \
                QLOGIC_IB_I_ERROR | QLOGIC_IB_I_SPIOSENT | \
                QLOGIC_IB_I_SPIOBUFAVAIL | QLOGIC_IB_I_GPIO)

/* kr_hwerrclear, kr_hwerrmask, kr_hwerrstatus, bits */
#define QLOGIC_IB_HWE_PCIEMEMPARITYERR_MASK  0x000000000000003fULL
#define QLOGIC_IB_HWE_PCIEMEMPARITYERR_SHIFT 0
#define QLOGIC_IB_HWE_PCIEPOISONEDTLP      0x0000000010000000ULL
#define QLOGIC_IB_HWE_PCIECPLTIMEOUT       0x0000000020000000ULL
#define QLOGIC_IB_HWE_PCIEBUSPARITYXTLH    0x0000000040000000ULL
#define QLOGIC_IB_HWE_PCIEBUSPARITYXADM    0x0000000080000000ULL
#define QLOGIC_IB_HWE_PCIEBUSPARITYRADM    0x0000000100000000ULL
#define QLOGIC_IB_HWE_COREPLL_FBSLIP       0x0080000000000000ULL
#define QLOGIC_IB_HWE_COREPLL_RFSLIP       0x0100000000000000ULL
#define QLOGIC_IB_HWE_PCIE1PLLFAILED       0x0400000000000000ULL
#define QLOGIC_IB_HWE_PCIE0PLLFAILED       0x0800000000000000ULL
#define QLOGIC_IB_HWE_SERDESPLLFAILED      0x1000000000000000ULL


/* kr_extstatus bits */
#define QLOGIC_IB_EXTS_FREQSEL 0x2
#define QLOGIC_IB_EXTS_SERDESSEL 0x4
#define QLOGIC_IB_EXTS_MEMBIST_ENDTEST     0x0000000000004000
#define QLOGIC_IB_EXTS_MEMBIST_FOUND       0x0000000000008000

/* kr_xgxsconfig bits */
#define QLOGIC_IB_XGXS_RESET          0x5ULL

#define _QIB_GPIO_SDA_NUM 1
#define _QIB_GPIO_SCL_NUM 0

/* Bits in GPIO for the added IB link interrupts */
#define GPIO_RXUVL_BIT 3
#define GPIO_OVRUN_BIT 4
#define GPIO_LLI_BIT 5
#define GPIO_ERRINTR_MASK 0x38


#define QLOGIC_IB_RT_BUFSIZE_MASK 0xe0000000ULL
#define QLOGIC_IB_RT_BUFSIZE_SHIFTVAL(tid) \
        ((((tid) & QLOGIC_IB_RT_BUFSIZE_MASK) >> 29) + 11 - 1)
#define QLOGIC_IB_RT_BUFSIZE(tid) (1 << QLOGIC_IB_RT_BUFSIZE_SHIFTVAL(tid))
#define QLOGIC_IB_RT_IS_VALID(tid) \
        (((tid) & QLOGIC_IB_RT_BUFSIZE_MASK) && \
         ((((tid) & QLOGIC_IB_RT_BUFSIZE_MASK) != QLOGIC_IB_RT_BUFSIZE_MASK)))
#define QLOGIC_IB_RT_ADDR_MASK 0x1FFFFFFFULL /* 29 bits valid */
#define QLOGIC_IB_RT_ADDR_SHIFT 10

#define QLOGIC_IB_R_INTRAVAIL_SHIFT 16
#define QLOGIC_IB_R_TAILUPD_SHIFT 31
#define IBA6120_R_PKEY_DIS_SHIFT 30

#define PBC_6120_VL15_SEND_CTRL (1ULL << 31) /* pbc; VL15; link_buf only */

#define IBCBUSFRSPCPARITYERR HWE_MASK(IBCBusFromSPCParityErr)
#define IBCBUSTOSPCPARITYERR HWE_MASK(IBCBusToSPCParityErr)

#define SYM_MASK_BIT(regname, fldname, bit) ((u64) \
        ((1ULL << (SYM_LSB(regname, fldname) + (bit)))))

#define TXEMEMPARITYERR_PIOBUF \
        SYM_MASK_BIT(HwErrMask, TXEMemParityErrMask, 0)
#define TXEMEMPARITYERR_PIOPBC \
        SYM_MASK_BIT(HwErrMask, TXEMemParityErrMask, 1)
#define TXEMEMPARITYERR_PIOLAUNCHFIFO \
        SYM_MASK_BIT(HwErrMask, TXEMemParityErrMask, 2)

#define RXEMEMPARITYERR_RCVBUF \
        SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 0)
#define RXEMEMPARITYERR_LOOKUPQ \
        SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 1)
#define RXEMEMPARITYERR_EXPTID \
        SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 2)
#define RXEMEMPARITYERR_EAGERTID \
        SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 3)
#define RXEMEMPARITYERR_FLAGBUF \
        SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 4)
#define RXEMEMPARITYERR_DATAINFO \
        SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 5)
#define RXEMEMPARITYERR_HDRINFO \
        SYM_MASK_BIT(HwErrMask, RXEMemParityErrMask, 6)

/* 6120 specific hardware errors... */
static const struct qib_hwerror_msgs qib_6120_hwerror_msgs[] = {
        /* generic hardware errors */
        QLOGIC_IB_HWE_MSG(IBCBUSFRSPCPARITYERR, "QIB2IB Parity"),
        QLOGIC_IB_HWE_MSG(IBCBUSTOSPCPARITYERR, "IB2QIB Parity"),

        QLOGIC_IB_HWE_MSG(TXEMEMPARITYERR_PIOBUF,
                          "TXE PIOBUF Memory Parity"),
        QLOGIC_IB_HWE_MSG(TXEMEMPARITYERR_PIOPBC,
                          "TXE PIOPBC Memory Parity"),
        QLOGIC_IB_HWE_MSG(TXEMEMPARITYERR_PIOLAUNCHFIFO,
                          "TXE PIOLAUNCHFIFO Memory Parity"),

        QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_RCVBUF,
                          "RXE RCVBUF Memory Parity"),
        QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_LOOKUPQ,
                          "RXE LOOKUPQ Memory Parity"),
        QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_EAGERTID,
                          "RXE EAGERTID Memory Parity"),
        QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_EXPTID,
                          "RXE EXPTID Memory Parity"),
        QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_FLAGBUF,
                          "RXE FLAGBUF Memory Parity"),
        QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_DATAINFO,
                          "RXE DATAINFO Memory Parity"),
        QLOGIC_IB_HWE_MSG(RXEMEMPARITYERR_HDRINFO,
                          "RXE HDRINFO Memory Parity"),

        /* chip-specific hardware errors */
        QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIEPOISONEDTLP,
                          "PCIe Poisoned TLP"),
        QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIECPLTIMEOUT,
                          "PCIe completion timeout"),
        /*
         * In practice, it's unlikely wthat we'll see PCIe PLL, or bus
         * parity or memory parity error failures, because most likely we
         * won't be able to talk to the core of the chip.  Nonetheless, we
         * might see them, if they are in parts of the PCIe core that aren't
         * essential.
         */
        QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIE1PLLFAILED,
                          "PCIePLL1"),
        QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIE0PLLFAILED,
                          "PCIePLL0"),
        QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIEBUSPARITYXTLH,
                          "PCIe XTLH core parity"),
        QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIEBUSPARITYXADM,
                          "PCIe ADM TX core parity"),
        QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_PCIEBUSPARITYRADM,
                          "PCIe ADM RX core parity"),
        QLOGIC_IB_HWE_MSG(QLOGIC_IB_HWE_SERDESPLLFAILED,
                          "SerDes PLL"),
};

#define TXE_PIO_PARITY (TXEMEMPARITYERR_PIOBUF | TXEMEMPARITYERR_PIOPBC)
#define _QIB_PLL_FAIL (QLOGIC_IB_HWE_COREPLL_FBSLIP |   \
                QLOGIC_IB_HWE_COREPLL_RFSLIP)

        /* variables for sanity checking interrupt and errors */
#define IB_HWE_BITSEXTANT \
        (HWE_MASK(RXEMemParityErr) |                                    \
         HWE_MASK(TXEMemParityErr) |                                    \
         (QLOGIC_IB_HWE_PCIEMEMPARITYERR_MASK <<                        \
          QLOGIC_IB_HWE_PCIEMEMPARITYERR_SHIFT) |                       \
         QLOGIC_IB_HWE_PCIE1PLLFAILED |                                 \
         QLOGIC_IB_HWE_PCIE0PLLFAILED |                                 \
         QLOGIC_IB_HWE_PCIEPOISONEDTLP |                                \
         QLOGIC_IB_HWE_PCIECPLTIMEOUT |                                 \
         QLOGIC_IB_HWE_PCIEBUSPARITYXTLH |                              \
         QLOGIC_IB_HWE_PCIEBUSPARITYXADM |                              \
         QLOGIC_IB_HWE_PCIEBUSPARITYRADM |                              \
         HWE_MASK(PowerOnBISTFailed) |                                  \
         QLOGIC_IB_HWE_COREPLL_FBSLIP |                                 \
         QLOGIC_IB_HWE_COREPLL_RFSLIP |                                 \
         QLOGIC_IB_HWE_SERDESPLLFAILED |                                \
         HWE_MASK(IBCBusToSPCParityErr) |                               \
         HWE_MASK(IBCBusFromSPCParityErr))

#define IB_E_BITSEXTANT \
        (ERR_MASK(RcvFormatErr) | ERR_MASK(RcvVCRCErr) |                \
         ERR_MASK(RcvICRCErr) | ERR_MASK(RcvMinPktLenErr) |             \
         ERR_MASK(RcvMaxPktLenErr) | ERR_MASK(RcvLongPktLenErr) |       \
         ERR_MASK(RcvShortPktLenErr) | ERR_MASK(RcvUnexpectedCharErr) | \
         ERR_MASK(RcvUnsupportedVLErr) | ERR_MASK(RcvEBPErr) |          \
         ERR_MASK(RcvIBFlowErr) | ERR_MASK(RcvBadVersionErr) |          \
         ERR_MASK(RcvEgrFullErr) | ERR_MASK(RcvHdrFullErr) |            \
         ERR_MASK(RcvBadTidErr) | ERR_MASK(RcvHdrLenErr) |              \
         ERR_MASK(RcvHdrErr) | ERR_MASK(RcvIBLostLinkErr) |             \
         ERR_MASK(SendMinPktLenErr) | ERR_MASK(SendMaxPktLenErr) |      \
         ERR_MASK(SendUnderRunErr) | ERR_MASK(SendPktLenErr) |          \
         ERR_MASK(SendDroppedSmpPktErr) |                               \
         ERR_MASK(SendDroppedDataPktErr) |                              \
         ERR_MASK(SendPioArmLaunchErr) |                                \
         ERR_MASK(SendUnexpectedPktNumErr) |                            \
         ERR_MASK(SendUnsupportedVLErr) | ERR_MASK(IBStatusChanged) |   \
         ERR_MASK(InvalidAddrErr) | ERR_MASK(ResetNegated) |            \
         ERR_MASK(HardwareErr))

#define QLOGIC_IB_E_PKTERRS ( \
                ERR_MASK(SendPktLenErr) |                               \
                ERR_MASK(SendDroppedDataPktErr) |                       \
                ERR_MASK(RcvVCRCErr) |                                  \
                ERR_MASK(RcvICRCErr) |                                  \
                ERR_MASK(RcvShortPktLenErr) |                           \
                ERR_MASK(RcvEBPErr))

/* These are all rcv-related errors which we want to count for stats */
#define E_SUM_PKTERRS                                           \
        (ERR_MASK(RcvHdrLenErr) | ERR_MASK(RcvBadTidErr) |              \
         ERR_MASK(RcvBadVersionErr) | ERR_MASK(RcvHdrErr) |             \
         ERR_MASK(RcvLongPktLenErr) | ERR_MASK(RcvShortPktLenErr) |     \
         ERR_MASK(RcvMaxPktLenErr) | ERR_MASK(RcvMinPktLenErr) |        \
         ERR_MASK(RcvFormatErr) | ERR_MASK(RcvUnsupportedVLErr) |       \
         ERR_MASK(RcvUnexpectedCharErr) | ERR_MASK(RcvEBPErr))

/* These are all send-related errors which we want to count for stats */
#define E_SUM_ERRS                                                      \
        (ERR_MASK(SendPioArmLaunchErr) |                                \
         ERR_MASK(SendUnexpectedPktNumErr) |                            \
         ERR_MASK(SendDroppedDataPktErr) |                              \
         ERR_MASK(SendDroppedSmpPktErr) |                               \
         ERR_MASK(SendMaxPktLenErr) | ERR_MASK(SendUnsupportedVLErr) |  \
         ERR_MASK(SendMinPktLenErr) | ERR_MASK(SendPktLenErr) |         \
         ERR_MASK(InvalidAddrErr))

/*
 * this is similar to E_SUM_ERRS, but can't ignore armlaunch, don't ignore
 * errors not related to freeze and cancelling buffers.  Can't ignore
 * armlaunch because could get more while still cleaning up, and need
 * to cancel those as they happen.
 */
#define E_SPKT_ERRS_IGNORE \
        (ERR_MASK(SendDroppedDataPktErr) |                              \
         ERR_MASK(SendDroppedSmpPktErr) |                               \
         ERR_MASK(SendMaxPktLenErr) | ERR_MASK(SendMinPktLenErr) |      \
         ERR_MASK(SendPktLenErr))

/*
 * these are errors that can occur when the link changes state while
 * a packet is being sent or received.  This doesn't cover things
 * like EBP or VCRC that can be the result of a sending having the
 * link change state, so we receive a "known bad" packet.
 */
#define E_SUM_LINK_PKTERRS              \
        (ERR_MASK(SendDroppedDataPktErr) |                              \
         ERR_MASK(SendDroppedSmpPktErr) |                               \
         ERR_MASK(SendMinPktLenErr) | ERR_MASK(SendPktLenErr) |         \
         ERR_MASK(RcvShortPktLenErr) | ERR_MASK(RcvMinPktLenErr) |      \
         ERR_MASK(RcvUnexpectedCharErr))

static void qib_6120_put_tid_2(struct qib_devdata *, u64 __iomem *,
                               u32, unsigned long);

/*
 * On platforms using this chip, and not having ordered WC stores, we
 * can get TXE parity errors due to speculative reads to the PIO buffers,
 * and this, due to a chip issue can result in (many) false parity error
 * reports.  So it's a debug print on those, and an info print on systems
 * where the speculative reads don't occur.
 */
static void qib_6120_txe_recover(struct qib_devdata *dd)
{
        if (!qib_unordered_wc())
                qib_devinfo(dd->pcidev,
                            "Recovering from TXE PIO parity error\n");
}

/* enable/disable chip from delivering interrupts */
static void qib_6120_set_intr_state(struct qib_devdata *dd, u32 enable)
{
        if (enable) {
                if (dd->flags & QIB_BADINTR)
                        return;
                qib_write_kreg(dd, kr_intmask, ~0ULL);
                /* force re-interrupt of any pending interrupts. */
                qib_write_kreg(dd, kr_intclear, 0ULL);
        } else
                qib_write_kreg(dd, kr_intmask, 0ULL);
}

/*
 * Try to cleanup as much as possible for anything that might have gone
 * wrong while in freeze mode, such as pio buffers being written by user
 * processes (causing armlaunch), send errors due to going into freeze mode,
 * etc., and try to avoid causing extra interrupts while doing so.
 * Forcibly update the in-memory pioavail register copies after cleanup
 * because the chip won't do it while in freeze mode (the register values
 * themselves are kept correct).
 * Make sure that we don't lose any important interrupts by using the chip
 * feature that says that writing 0 to a bit in *clear that is set in
 * *status will cause an interrupt to be generated again (if allowed by
 * the *mask value).
 * This is in chip-specific code because of all of the register accesses,
 * even though the details are similar on most chips
 */
static void qib_6120_clear_freeze(struct qib_devdata *dd)
{
        /* disable error interrupts, to avoid confusion */
        qib_write_kreg(dd, kr_errmask, 0ULL);

        /* also disable interrupts; errormask is sometimes overwriten */
        qib_6120_set_intr_state(dd, 0);

        qib_cancel_sends(dd->pport);

        /* clear the freeze, and be sure chip saw it */
        qib_write_kreg(dd, kr_control, dd->control);
        qib_read_kreg32(dd, kr_scratch);

        /* force in-memory update now we are out of freeze */
        qib_force_pio_avail_update(dd);

        /*
         * force new interrupt if any hwerr, error or interrupt bits are
         * still set, and clear "safe" send packet errors related to freeze
         * and cancelling sends.  Re-enable error interrupts before possible
         * force of re-interrupt on pending interrupts.
         */
        qib_write_kreg(dd, kr_hwerrclear, 0ULL);
        qib_write_kreg(dd, kr_errclear, E_SPKT_ERRS_IGNORE);
        qib_write_kreg(dd, kr_errmask, dd->cspec->errormask);
        qib_6120_set_intr_state(dd, 1);
}

/**
 * qib_handle_6120_hwerrors - display hardware errors.
 * @dd: the qlogic_ib device
 * @msg: the output buffer
 * @msgl: the size of the output buffer
 *
 * Use same msg buffer as regular errors to avoid excessive stack
 * use.  Most hardware errors are catastrophic, but for right now,
 * we'll print them and continue.  Reuse the same message buffer as
 * handle_6120_errors() to avoid excessive stack usage.
 */
static void qib_handle_6120_hwerrors(struct qib_devdata *dd, char *msg,
                                     size_t msgl)
{
        u64 hwerrs;
        u32 bits, ctrl;
        int isfatal = 0;
        char *bitsmsg;
        int log_idx;

        hwerrs = qib_read_kreg64(dd, kr_hwerrstatus);
        if (!hwerrs)
                return;
        if (hwerrs == ~0ULL) {
                qib_dev_err(dd,
                        "Read of hardware error status failed (all bits set); ignoring\n");
                return;
        }
        qib_stats.sps_hwerrs++;

        /* Always clear the error status register, except MEMBISTFAIL,
         * regardless of whether we continue or stop using the chip.
         * We want that set so we know it failed, even across driver reload.
         * We'll still ignore it in the hwerrmask.  We do this partly for
         * diagnostics, but also for support */
        qib_write_kreg(dd, kr_hwerrclear,
                       hwerrs & ~HWE_MASK(PowerOnBISTFailed));

        hwerrs &= dd->cspec->hwerrmask;

        /* We log some errors to EEPROM, check if we have any of those. */
        for (log_idx = 0; log_idx < QIB_EEP_LOG_CNT; ++log_idx)
                if (hwerrs & dd->eep_st_masks[log_idx].hwerrs_to_log)
                        qib_inc_eeprom_err(dd, log_idx, 1);

        /*
         * Make sure we get this much out, unless told to be quiet,
         * or it's occurred within the last 5 seconds.
         */
        if (hwerrs & ~(TXE_PIO_PARITY | RXEMEMPARITYERR_EAGERTID))
                qib_devinfo(dd->pcidev,
                        "Hardware error: hwerr=0x%llx (cleared)\n",
                        (unsigned long long) hwerrs);

        if (hwerrs & ~IB_HWE_BITSEXTANT)
                qib_dev_err(dd,
                        "hwerror interrupt with unknown errors %llx set\n",
                        (unsigned long long)(hwerrs & ~IB_HWE_BITSEXTANT));

        ctrl = qib_read_kreg32(dd, kr_control);
        if ((ctrl & QLOGIC_IB_C_FREEZEMODE) && !dd->diag_client) {
                /*
                 * Parity errors in send memory are recoverable,
                 * just cancel the send (if indicated in * sendbuffererror),
                 * count the occurrence, unfreeze (if no other handled
                 * hardware error bits are set), and continue. They can
                 * occur if a processor speculative read is done to the PIO
                 * buffer while we are sending a packet, for example.
                 */
                if (hwerrs & TXE_PIO_PARITY) {
                        qib_6120_txe_recover(dd);
                        hwerrs &= ~TXE_PIO_PARITY;
                }

                if (!hwerrs) {
                        static u32 freeze_cnt;

                        freeze_cnt++;
                        qib_6120_clear_freeze(dd);
                } else
                        isfatal = 1;
        }

        *msg = '\0';

        if (hwerrs & HWE_MASK(PowerOnBISTFailed)) {
                isfatal = 1;
                strlcat(msg,
                        "[Memory BIST test failed, InfiniPath hardware unusable]",
                        msgl);
                /* ignore from now on, so disable until driver reloaded */
                dd->cspec->hwerrmask &= ~HWE_MASK(PowerOnBISTFailed);
                qib_write_kreg(dd, kr_hwerrmask, dd->cspec->hwerrmask);
        }

        qib_format_hwerrors(hwerrs, qib_6120_hwerror_msgs,
                            ARRAY_SIZE(qib_6120_hwerror_msgs), msg, msgl);

        bitsmsg = dd->cspec->bitsmsgbuf;
        if (hwerrs & (QLOGIC_IB_HWE_PCIEMEMPARITYERR_MASK <<
                      QLOGIC_IB_HWE_PCIEMEMPARITYERR_SHIFT)) {
                bits = (u32) ((hwerrs >>
                               QLOGIC_IB_HWE_PCIEMEMPARITYERR_SHIFT) &
                              QLOGIC_IB_HWE_PCIEMEMPARITYERR_MASK);
                snprintf(bitsmsg, sizeof(dd->cspec->bitsmsgbuf),
                         "[PCIe Mem Parity Errs %x] ", bits);
                strlcat(msg, bitsmsg, msgl);
        }

        if (hwerrs & _QIB_PLL_FAIL) {
                isfatal = 1;
                snprintf(bitsmsg, sizeof(dd->cspec->bitsmsgbuf),
                         "[PLL failed (%llx), InfiniPath hardware unusable]",
                         (unsigned long long) hwerrs & _QIB_PLL_FAIL);
                strlcat(msg, bitsmsg, msgl);
                /* ignore from now on, so disable until driver reloaded */
                dd->cspec->hwerrmask &= ~(hwerrs & _QIB_PLL_FAIL);
                qib_write_kreg(dd, kr_hwerrmask, dd->cspec->hwerrmask);
        }

        if (hwerrs & QLOGIC_IB_HWE_SERDESPLLFAILED) {
                /*
                 * If it occurs, it is left masked since the external
                 * interface is unused
                 */
                dd->cspec->hwerrmask &= ~QLOGIC_IB_HWE_SERDESPLLFAILED;
                qib_write_kreg(dd, kr_hwerrmask, dd->cspec->hwerrmask);
        }

        if (hwerrs)
                /*
                 * if any set that we aren't ignoring; only
                 * make the complaint once, in case it's stuck
                 * or recurring, and we get here multiple
                 * times.
                 */
                qib_dev_err(dd, "%s hardware error\n", msg);
        else
                *msg = 0; /* recovered from all of them */

        if (isfatal && !dd->diag_client) {
                qib_dev_err(dd,
                        "Fatal Hardware Error, no longer usable, SN %.16s\n",
                        dd->serial);
                /*
                 * for /sys status file and user programs to print; if no
                 * trailing brace is copied, we'll know it was truncated.
                 */
                if (dd->freezemsg)
                        snprintf(dd->freezemsg, dd->freezelen,
                                 "{%s}", msg);
                qib_disable_after_error(dd);
        }
}

/*
 * Decode the error status into strings, deciding whether to always
 * print * it or not depending on "normal packet errors" vs everything
 * else.   Return 1 if "real" errors, otherwise 0 if only packet
 * errors, so caller can decide what to print with the string.
 */
static int qib_decode_6120_err(struct qib_devdata *dd, char *buf, size_t blen,
                               u64 err)
{
        int iserr = 1;

        *buf = '\0';
        if (err & QLOGIC_IB_E_PKTERRS) {
                if (!(err & ~QLOGIC_IB_E_PKTERRS))
                        iserr = 0;
                if ((err & ERR_MASK(RcvICRCErr)) &&
                    !(err&(ERR_MASK(RcvVCRCErr)|ERR_MASK(RcvEBPErr))))
                        strlcat(buf, "CRC ", blen);
                if (!iserr)
                        goto done;
        }
        if (err & ERR_MASK(RcvHdrLenErr))
                strlcat(buf, "rhdrlen ", blen);
        if (err & ERR_MASK(RcvBadTidErr))
                strlcat(buf, "rbadtid ", blen);
        if (err & ERR_MASK(RcvBadVersionErr))
                strlcat(buf, "rbadversion ", blen);
        if (err & ERR_MASK(RcvHdrErr))
                strlcat(buf, "rhdr ", blen);
        if (err & ERR_MASK(RcvLongPktLenErr))
                strlcat(buf, "rlongpktlen ", blen);
        if (err & ERR_MASK(RcvMaxPktLenErr))
                strlcat(buf, "rmaxpktlen ", blen);
        if (err & ERR_MASK(RcvMinPktLenErr))
                strlcat(buf, "rminpktlen ", blen);
        if (err & ERR_MASK(SendMinPktLenErr))
                strlcat(buf, "sminpktlen ", blen);
        if (err & ERR_MASK(RcvFormatErr))
                strlcat(buf, "rformaterr ", blen);
        if (err & ERR_MASK(RcvUnsupportedVLErr))
                strlcat(buf, "runsupvl ", blen);
        if (err & ERR_MASK(RcvUnexpectedCharErr))
                strlcat(buf, "runexpchar ", blen);
        if (err & ERR_MASK(RcvIBFlowErr))
                strlcat(buf, "ribflow ", blen);
        if (err & ERR_MASK(SendUnderRunErr))
                strlcat(buf, "sunderrun ", blen);
        if (err & ERR_MASK(SendPioArmLaunchErr))
                strlcat(buf, "spioarmlaunch ", blen);
        if (err & ERR_MASK(SendUnexpectedPktNumErr))
                strlcat(buf, "sunexperrpktnum ", blen);
        if (err & ERR_MASK(SendDroppedSmpPktErr))
                strlcat(buf, "sdroppedsmppkt ", blen);
        if (err & ERR_MASK(SendMaxPktLenErr))
                strlcat(buf, "smaxpktlen ", blen);
        if (err & ERR_MASK(SendUnsupportedVLErr))
                strlcat(buf, "sunsupVL ", blen);
        if (err & ERR_MASK(InvalidAddrErr))
                strlcat(buf, "invalidaddr ", blen);
        if (err & ERR_MASK(RcvEgrFullErr))
                strlcat(buf, "rcvegrfull ", blen);
        if (err & ERR_MASK(RcvHdrFullErr))
                strlcat(buf, "rcvhdrfull ", blen);
        if (err & ERR_MASK(IBStatusChanged))
                strlcat(buf, "ibcstatuschg ", blen);
        if (err & ERR_MASK(RcvIBLostLinkErr))
                strlcat(buf, "riblostlink ", blen);
        if (err & ERR_MASK(HardwareErr))
                strlcat(buf, "hardware ", blen);
        if (err & ERR_MASK(ResetNegated))
                strlcat(buf, "reset ", blen);
done:
        return iserr;
}

/*
 * Called when we might have an error that is specific to a particular
 * PIO buffer, and may need to cancel that buffer, so it can be re-used.
 */
static void qib_disarm_6120_senderrbufs(struct qib_pportdata *ppd)
{
        unsigned long sbuf[2];
        struct qib_devdata *dd = ppd->dd;

        /*
         * It's possible that sendbuffererror could have bits set; might
         * have already done this as a result of hardware error handling.
         */
        sbuf[0] = qib_read_kreg64(dd, kr_sendbuffererror);
        sbuf[1] = qib_read_kreg64(dd, kr_sendbuffererror + 1);

        if (sbuf[0] || sbuf[1])
                qib_disarm_piobufs_set(dd, sbuf,
                                       dd->piobcnt2k + dd->piobcnt4k);
}

static int chk_6120_linkrecovery(struct qib_devdata *dd, u64 ibcs)
{
        int ret = 1;
        u32 ibstate = qib_6120_iblink_state(ibcs);
        u32 linkrecov = read_6120_creg32(dd, cr_iblinkerrrecov);

        if (linkrecov != dd->cspec->lastlinkrecov) {
                /* and no more until active again */
                dd->cspec->lastlinkrecov = 0;
                qib_set_linkstate(dd->pport, QIB_IB_LINKDOWN);
                ret = 0;
        }
        if (ibstate == IB_PORT_ACTIVE)
                dd->cspec->lastlinkrecov =
                        read_6120_creg32(dd, cr_iblinkerrrecov);
        return ret;
}

static void handle_6120_errors(struct qib_devdata *dd, u64 errs)
{
        char *msg;
        u64 ignore_this_time = 0;
        u64 iserr = 0;
        int log_idx;
        struct qib_pportdata *ppd = dd->pport;
        u64 mask;

        /* don't report errors that are masked */
        errs &= dd->cspec->errormask;
        msg = dd->cspec->emsgbuf;

        /* do these first, they are most important */
        if (errs & ERR_MASK(HardwareErr))
                qib_handle_6120_hwerrors(dd, msg, sizeof(dd->cspec->emsgbuf));
        else
                for (log_idx = 0; log_idx < QIB_EEP_LOG_CNT; ++log_idx)
                        if (errs & dd->eep_st_masks[log_idx].errs_to_log)
                                qib_inc_eeprom_err(dd, log_idx, 1);

        if (errs & ~IB_E_BITSEXTANT)
                qib_dev_err(dd,
                        "error interrupt with unknown errors %llx set\n",
                        (unsigned long long) (errs & ~IB_E_BITSEXTANT));

        if (errs & E_SUM_ERRS) {
                qib_disarm_6120_senderrbufs(ppd);
                if ((errs & E_SUM_LINK_PKTERRS) &&
                    !(ppd->lflags & QIBL_LINKACTIVE)) {
                        /*
                         * This can happen when trying to bring the link
                         * up, but the IB link changes state at the "wrong"
                         * time. The IB logic then complains that the packet
                         * isn't valid.  We don't want to confuse people, so
                         * we just don't print them, except at debug
                         */
                        ignore_this_time = errs & E_SUM_LINK_PKTERRS;
                }
        } else if ((errs & E_SUM_LINK_PKTERRS) &&
                   !(ppd->lflags & QIBL_LINKACTIVE)) {
                /*
                 * This can happen when SMA is trying to bring the link
                 * up, but the IB link changes state at the "wrong" time.
                 * The IB logic then complains that the packet isn't
                 * valid.  We don't want to confuse people, so we just
                 * don't print them, except at debug
                 */
                ignore_this_time = errs & E_SUM_LINK_PKTERRS;
        }

        qib_write_kreg(dd, kr_errclear, errs);

        errs &= ~ignore_this_time;
        if (!errs)
                goto done;

        /*
         * The ones we mask off are handled specially below
         * or above.
         */
        mask = ERR_MASK(IBStatusChanged) | ERR_MASK(RcvEgrFullErr) |
                ERR_MASK(RcvHdrFullErr) | ERR_MASK(HardwareErr);
        qib_decode_6120_err(dd, msg, sizeof(dd->cspec->emsgbuf), errs & ~mask);

        if (errs & E_SUM_PKTERRS)
                qib_stats.sps_rcverrs++;
        if (errs & E_SUM_ERRS)
                qib_stats.sps_txerrs++;

        iserr = errs & ~(E_SUM_PKTERRS | QLOGIC_IB_E_PKTERRS);

        if (errs & ERR_MASK(IBStatusChanged)) {
                u64 ibcs = qib_read_kreg64(dd, kr_ibcstatus);
                u32 ibstate = qib_6120_iblink_state(ibcs);
                int handle = 1;

                if (ibstate != IB_PORT_INIT && dd->cspec->lastlinkrecov)
                        handle = chk_6120_linkrecovery(dd, ibcs);
                /*
                 * Since going into a recovery state causes the link state
                 * to go down and since recovery is transitory, it is better
                 * if we "miss" ever seeing the link training state go into
                 * recovery (i.e., ignore this transition for link state
                 * special handling purposes) without updating lastibcstat.
                 */
                if (handle && qib_6120_phys_portstate(ibcs) ==
                                            IB_PHYSPORTSTATE_LINK_ERR_RECOVER)
                        handle = 0;
                if (handle)
                        qib_handle_e_ibstatuschanged(ppd, ibcs);
        }

        if (errs & ERR_MASK(ResetNegated)) {
                qib_dev_err(dd,
                        "Got reset, requires re-init (unload and reload driver)\n");
                dd->flags &= ~QIB_INITTED;  /* needs re-init */
                /* mark as having had error */
                *dd->devstatusp |= QIB_STATUS_HWERROR;
                *dd->pport->statusp &= ~QIB_STATUS_IB_CONF;
        }

        if (*msg && iserr)
                qib_dev_porterr(dd, ppd->port, "%s error\n", msg);

        if (ppd->state_wanted & ppd->lflags)
                wake_up_interruptible(&ppd->state_wait);

        /*
         * If there were hdrq or egrfull errors, wake up any processes
         * waiting in poll.  We used to try to check which contexts had
         * the overflow, but given the cost of that and the chip reads
         * to support it, it's better to just wake everybody up if we
         * get an overflow; waiters can poll again if it's not them.
         */
        if (errs & (ERR_MASK(RcvEgrFullErr) | ERR_MASK(RcvHdrFullErr))) {
                qib_handle_urcv(dd, ~0U);
                if (errs & ERR_MASK(RcvEgrFullErr))
                        qib_stats.sps_buffull++;
                else
                        qib_stats.sps_hdrfull++;
        }
done:
        return;
}

/**
 * qib_6120_init_hwerrors - enable hardware errors
 * @dd: the qlogic_ib device
 *
 * now that we have finished initializing everything that might reasonably
 * cause a hardware error, and cleared those errors bits as they occur,
 * we can enable hardware errors in the mask (potentially enabling
 * freeze mode), and enable hardware errors as errors (along with
 * everything else) in errormask
 */
static void qib_6120_init_hwerrors(struct qib_devdata *dd)
{
        u64 val;
        u64 extsval;

        extsval = qib_read_kreg64(dd, kr_extstatus);

        if (!(extsval & QLOGIC_IB_EXTS_MEMBIST_ENDTEST))
                qib_dev_err(dd, "MemBIST did not complete!\n");

        /* init so all hwerrors interrupt, and enter freeze, ajdust below */
        val = ~0ULL;
        if (dd->minrev < 2) {
                /*
                 * Avoid problem with internal interface bus parity
                 * checking. Fixed in Rev2.
                 */
                val &= ~QLOGIC_IB_HWE_PCIEBUSPARITYRADM;
        }
        /* avoid some intel cpu's speculative read freeze mode issue */
        val &= ~TXEMEMPARITYERR_PIOBUF;

        dd->cspec->hwerrmask = val;

        qib_write_kreg(dd, kr_hwerrclear, ~HWE_MASK(PowerOnBISTFailed));
        qib_write_kreg(dd, kr_hwerrmask, dd->cspec->hwerrmask);

        /* clear all */
        qib_write_kreg(dd, kr_errclear, ~0ULL);
        /* enable errors that are masked, at least this first time. */
        qib_write_kreg(dd, kr_errmask, ~0ULL);
        dd->cspec->errormask = qib_read_kreg64(dd, kr_errmask);
        /* clear any interrupts up to this point (ints still not enabled) */
        qib_write_kreg(dd, kr_intclear, ~0ULL);

        qib_write_kreg(dd, kr_rcvbthqp,
                       dd->qpn_mask << (QIB_6120_RcvBTHQP_BTHQP_Mask_LSB - 1) |
                       QIB_KD_QP);
}

/*
 * Disable and enable the armlaunch error.  Used for PIO bandwidth testing
 * on chips that are count-based, rather than trigger-based.  There is no
 * reference counting, but that's also fine, given the intended use.
 * Only chip-specific because it's all register accesses
 */
static void qib_set_6120_armlaunch(struct qib_devdata *dd, u32 enable)
{
        if (enable) {
                qib_write_kreg(dd, kr_errclear,
                               ERR_MASK(SendPioArmLaunchErr));
                dd->cspec->errormask |= ERR_MASK(SendPioArmLaunchErr);
        } else
                dd->cspec->errormask &= ~ERR_MASK(SendPioArmLaunchErr);
        qib_write_kreg(dd, kr_errmask, dd->cspec->errormask);
}

/*
 * Formerly took parameter <which> in pre-shifted,
 * pre-merged form with LinkCmd and LinkInitCmd
 * together, and assuming the zero was NOP.
 */
static void qib_set_ib_6120_lstate(struct qib_pportdata *ppd, u16 linkcmd,
                                   u16 linitcmd)
{
        u64 mod_wd;
        struct qib_devdata *dd = ppd->dd;
        unsigned long flags;

        if (linitcmd == QLOGIC_IB_IBCC_LINKINITCMD_DISABLE) {
                /*
                 * If we are told to disable, note that so link-recovery
                 * code does not attempt to bring us back up.
                 */
                spin_lock_irqsave(&ppd->lflags_lock, flags);
                ppd->lflags |= QIBL_IB_LINK_DISABLED;
                spin_unlock_irqrestore(&ppd->lflags_lock, flags);
        } else if (linitcmd || linkcmd == QLOGIC_IB_IBCC_LINKCMD_DOWN) {
                /*
                 * Any other linkinitcmd will lead to LINKDOWN and then
                 * to INIT (if all is well), so clear flag to let
                 * link-recovery code attempt to bring us back up.
                 */
                spin_lock_irqsave(&ppd->lflags_lock, flags);
                ppd->lflags &= ~QIBL_IB_LINK_DISABLED;
                spin_unlock_irqrestore(&ppd->lflags_lock, flags);
        }

        mod_wd = (linkcmd << QLOGIC_IB_IBCC_LINKCMD_SHIFT) |
                (linitcmd << QLOGIC_IB_IBCC_LINKINITCMD_SHIFT);

        qib_write_kreg(dd, kr_ibcctrl, dd->cspec->ibcctrl | mod_wd);
        /* write to chip to prevent back-to-back writes of control reg */
        qib_write_kreg(dd, kr_scratch, 0);
}

/**
 * qib_6120_bringup_serdes - bring up the serdes
 * @dd: the qlogic_ib device
 */
static int qib_6120_bringup_serdes(struct qib_pportdata *ppd)
{
        struct qib_devdata *dd = ppd->dd;
        u64 val, config1, prev_val, hwstat, ibc;

        /* Put IBC in reset, sends disabled */
        dd->control &= ~QLOGIC_IB_C_LINKENABLE;
        qib_write_kreg(dd, kr_control, 0ULL);

        dd->cspec->ibdeltainprog = 1;
        dd->cspec->ibsymsnap = read_6120_creg32(dd, cr_ibsymbolerr);
        dd->cspec->iblnkerrsnap = read_6120_creg32(dd, cr_iblinkerrrecov);

        /* flowcontrolwatermark is in units of KBytes */
        ibc = 0x5ULL << SYM_LSB(IBCCtrl, FlowCtrlWaterMark);
        /*
         * How often flowctrl sent.  More or less in usecs; balance against
         * watermark value, so that in theory senders always get a flow
         * control update in time to not let the IB link go idle.
         */
        ibc |= 0x3ULL << SYM_LSB(IBCCtrl, FlowCtrlPeriod);
        /* max error tolerance */
        dd->cspec->lli_thresh = 0xf;
        ibc |= (u64) dd->cspec->lli_thresh << SYM_LSB(IBCCtrl, PhyerrThreshold);
        /* use "real" buffer space for */
        ibc |= 4ULL << SYM_LSB(IBCCtrl, CreditScale);
        /* IB credit flow control. */
        ibc |= 0xfULL << SYM_LSB(IBCCtrl, OverrunThreshold);
        /*
         * set initial max size pkt IBC will send, including ICRC; it's the
         * PIO buffer size in dwords, less 1; also see qib_set_mtu()
         */
        ibc |= ((u64)(ppd->ibmaxlen >> 2) + 1) << SYM_LSB(IBCCtrl, MaxPktLen);
        dd->cspec->ibcctrl = ibc; /* without linkcmd or linkinitcmd! */

        /* initially come up waiting for TS1, without sending anything. */
        val = dd->cspec->ibcctrl | (QLOGIC_IB_IBCC_LINKINITCMD_DISABLE <<
                QLOGIC_IB_IBCC_LINKINITCMD_SHIFT);
        qib_write_kreg(dd, kr_ibcctrl, val);

        val = qib_read_kreg64(dd, kr_serdes_cfg0);
        config1 = qib_read_kreg64(dd, kr_serdes_cfg1);

        /*
         * Force reset on, also set rxdetect enable.  Must do before reading
         * serdesstatus at least for simulation, or some of the bits in
         * serdes status will come back as undefined and cause simulation
         * failures
         */
        val |= SYM_MASK(SerdesCfg0, ResetPLL) |
                SYM_MASK(SerdesCfg0, RxDetEnX) |
                (SYM_MASK(SerdesCfg0, L1PwrDnA) |
                 SYM_MASK(SerdesCfg0, L1PwrDnB) |
                 SYM_MASK(SerdesCfg0, L1PwrDnC) |
                 SYM_MASK(SerdesCfg0, L1PwrDnD));
        qib_write_kreg(dd, kr_serdes_cfg0, val);
        /* be sure chip saw it */
        qib_read_kreg64(dd, kr_scratch);
        udelay(5);              /* need pll reset set at least for a bit */
        /*
         * after PLL is reset, set the per-lane Resets and TxIdle and
         * clear the PLL reset and rxdetect (to get falling edge).
         * Leave L1PWR bits set (permanently)
         */
        val &= ~(SYM_MASK(SerdesCfg0, RxDetEnX) |
                 SYM_MASK(SerdesCfg0, ResetPLL) |
                 (SYM_MASK(SerdesCfg0, L1PwrDnA) |
                  SYM_MASK(SerdesCfg0, L1PwrDnB) |
                  SYM_MASK(SerdesCfg0, L1PwrDnC) |
                  SYM_MASK(SerdesCfg0, L1PwrDnD)));
        val |= (SYM_MASK(SerdesCfg0, ResetA) |
                SYM_MASK(SerdesCfg0, ResetB) |
                SYM_MASK(SerdesCfg0, ResetC) |
                SYM_MASK(SerdesCfg0, ResetD)) |
                SYM_MASK(SerdesCfg0, TxIdeEnX);
        qib_write_kreg(dd, kr_serdes_cfg0, val);
        /* be sure chip saw it */
        (void) qib_read_kreg64(dd, kr_scratch);
        /* need PLL reset clear for at least 11 usec before lane
         * resets cleared; give it a few more to be sure */
        udelay(15);
        val &= ~((SYM_MASK(SerdesCfg0, ResetA) |
                  SYM_MASK(SerdesCfg0, ResetB) |
                  SYM_MASK(SerdesCfg0, ResetC) |
                  SYM_MASK(SerdesCfg0, ResetD)) |
                 SYM_MASK(SerdesCfg0, TxIdeEnX));

        qib_write_kreg(dd, kr_serdes_cfg0, val);
        /* be sure chip saw it */
        (void) qib_read_kreg64(dd, kr_scratch);

        val = qib_read_kreg64(dd, kr_xgxs_cfg);
        prev_val = val;
        if (val & QLOGIC_IB_XGXS_RESET)
                val &= ~QLOGIC_IB_XGXS_RESET;
        if (SYM_FIELD(val, XGXSCfg, polarity_inv) != ppd->rx_pol_inv) {
                /* need to compensate for Tx inversion in partner */
                val &= ~SYM_MASK(XGXSCfg, polarity_inv);
                val |= (u64)ppd->rx_pol_inv << SYM_LSB(XGXSCfg, polarity_inv);
        }
        if (val != prev_val)
                qib_write_kreg(dd, kr_xgxs_cfg, val);

        val = qib_read_kreg64(dd, kr_serdes_cfg0);

        /* clear current and de-emphasis bits */
        config1 &= ~0x0ffffffff00ULL;
        /* set current to 20ma */
        config1 |= 0x00000000000ULL;
        /* set de-emphasis to -5.68dB */
        config1 |= 0x0cccc000000ULL;
        qib_write_kreg(dd, kr_serdes_cfg1, config1);

        /* base and port guid same for single port */
        ppd->guid = dd->base_guid;

        /*
         * the process of setting and un-resetting the serdes normally
         * causes a serdes PLL error, so check for that and clear it
         * here.  Also clearr hwerr bit in errstatus, but not others.
         */
        hwstat = qib_read_kreg64(dd, kr_hwerrstatus);
        if (hwstat) {
                /* should just have PLL, clear all set, in an case */
                qib_write_kreg(dd, kr_hwerrclear, hwstat);
                qib_write_kreg(dd, kr_errclear, ERR_MASK(HardwareErr));
        }

        dd->control |= QLOGIC_IB_C_LINKENABLE;
        dd->control &= ~QLOGIC_IB_C_FREEZEMODE;
        qib_write_kreg(dd, kr_control, dd->control);

        return 0;
}

/**
 * qib_6120_quiet_serdes - set serdes to txidle
 * @ppd: physical port of the qlogic_ib device
 * Called when driver is being unloaded
 */
static void qib_6120_quiet_serdes(struct qib_pportdata *ppd)
{
        struct qib_devdata *dd = ppd->dd;
        u64 val;

        qib_set_ib_6120_lstate(ppd, 0, QLOGIC_IB_IBCC_LINKINITCMD_DISABLE);

        /* disable IBC */
        dd->control &= ~QLOGIC_IB_C_LINKENABLE;
        qib_write_kreg(dd, kr_control,
                       dd->control | QLOGIC_IB_C_FREEZEMODE);

        if (dd->cspec->ibsymdelta || dd->cspec->iblnkerrdelta ||
            dd->cspec->ibdeltainprog) {
                u64 diagc;

                /* enable counter writes */
                diagc = qib_read_kreg64(dd, kr_hwdiagctrl);
                qib_write_kreg(dd, kr_hwdiagctrl,
                               diagc | SYM_MASK(HwDiagCtrl, CounterWrEnable));

                if (dd->cspec->ibsymdelta || dd->cspec->ibdeltainprog) {
                        val = read_6120_creg32(dd, cr_ibsymbolerr);
                        if (dd->cspec->ibdeltainprog)
                                val -= val - dd->cspec->ibsymsnap;
                        val -= dd->cspec->ibsymdelta;
                        write_6120_creg(dd, cr_ibsymbolerr, val);
                }
                if (dd->cspec->iblnkerrdelta || dd->cspec->ibdeltainprog) {
                        val = read_6120_creg32(dd, cr_iblinkerrrecov);
                        if (dd->cspec->ibdeltainprog)
                                val -= val - dd->cspec->iblnkerrsnap;
                        val -= dd->cspec->iblnkerrdelta;
                        write_6120_creg(dd, cr_iblinkerrrecov, val);
                }

                /* and disable counter writes */
                qib_write_kreg(dd, kr_hwdiagctrl, diagc);
        }

        val = qib_read_kreg64(dd, kr_serdes_cfg0);
        val |= SYM_MASK(SerdesCfg0, TxIdeEnX);
        qib_write_kreg(dd, kr_serdes_cfg0, val);
}

/**
 * qib_6120_setup_setextled - set the state of the two external LEDs
 * @dd: the qlogic_ib device
 * @on: whether the link is up or not
 *
 * The exact combo of LEDs if on is true is determined by looking
 * at the ibcstatus.

 * These LEDs indicate the physical and logical state of IB link.
 * For this chip (at least with recommended board pinouts), LED1
 * is Yellow (logical state) and LED2 is Green (physical state),
 *
 * Note:  We try to match the Mellanox HCA LED behavior as best
 * we can.  Green indicates physical link state is OK (something is
 * plugged in, and we can train).
 * Amber indicates the link is logically up (ACTIVE).
 * Mellanox further blinks the amber LED to indicate data packet
 * activity, but we have no hardware support for that, so it would
 * require waking up every 10-20 msecs and checking the counters
 * on the chip, and then turning the LED off if appropriate.  That's
 * visible overhead, so not something we will do.
 *
 */
static void qib_6120_setup_setextled(struct qib_pportdata *ppd, u32 on)
{
        u64 extctl, val, lst, ltst;
        unsigned long flags;
        struct qib_devdata *dd = ppd->dd;

        /*
         * The diags use the LED to indicate diag info, so we leave
         * the external LED alone when the diags are running.
         */
        if (dd->diag_client)
                return;

        /* Allow override of LED display for, e.g. Locating system in rack */
        if (ppd->led_override) {
                ltst = (ppd->led_override & QIB_LED_PHYS) ?
                        IB_PHYSPORTSTATE_LINKUP : IB_PHYSPORTSTATE_DISABLED,
                lst = (ppd->led_override & QIB_LED_LOG) ?
                        IB_PORT_ACTIVE : IB_PORT_DOWN;
        } else if (on) {
                val = qib_read_kreg64(dd, kr_ibcstatus);
                ltst = qib_6120_phys_portstate(val);
                lst = qib_6120_iblink_state(val);
        } else {
                ltst = 0;
                lst = 0;
        }

        spin_lock_irqsave(&dd->cspec->gpio_lock, flags);
        extctl = dd->cspec->extctrl & ~(SYM_MASK(EXTCtrl, LEDPriPortGreenOn) |
                                 SYM_MASK(EXTCtrl, LEDPriPortYellowOn));

        if (ltst == IB_PHYSPORTSTATE_LINKUP)
                extctl |= SYM_MASK(EXTCtrl, LEDPriPortYellowOn);
        if (lst == IB_PORT_ACTIVE)
                extctl |= SYM_MASK(EXTCtrl, LEDPriPortGreenOn);
        dd->cspec->extctrl = extctl;
        qib_write_kreg(dd, kr_extctrl, extctl);
        spin_unlock_irqrestore(&dd->cspec->gpio_lock, flags);
}

static void qib_6120_free_irq(struct qib_devdata *dd)
{
        if (dd->cspec->irq) {
                free_irq(dd->cspec->irq, dd);
                dd->cspec->irq = 0;
        }
        qib_nomsi(dd);
}

/**
 * qib_6120_setup_cleanup - clean up any per-chip chip-specific stuff
 * @dd: the qlogic_ib device
 *
 * This is called during driver unload.
*/
static void qib_6120_setup_cleanup(struct qib_devdata *dd)
{
        qib_6120_free_irq(dd);
        kfree(dd->cspec->cntrs);
        kfree(dd->cspec->portcntrs);
        if (dd->cspec->dummy_hdrq) {
                dma_free_coherent(&dd->pcidev->dev,
                                  ALIGN(dd->rcvhdrcnt *
                                        dd->rcvhdrentsize *
                                        sizeof(u32), PAGE_SIZE),
                                  dd->cspec->dummy_hdrq,
                                  dd->cspec->dummy_hdrq_phys);
                dd->cspec->dummy_hdrq = NULL;
        }
}

static void qib_wantpiobuf_6120_intr(struct qib_devdata *dd, u32 needint)
{
        unsigned long flags;

        spin_lock_irqsave(&dd->sendctrl_lock, flags);
        if (needint)
                dd->sendctrl |= SYM_MASK(SendCtrl, PIOIntBufAvail);
        else
                dd->sendctrl &= ~SYM_MASK(SendCtrl, PIOIntBufAvail);
        qib_write_kreg(dd, kr_sendctrl, dd->sendctrl);
        qib_write_kreg(dd, kr_scratch, 0ULL);
        spin_unlock_irqrestore(&dd->sendctrl_lock, flags);
}

/*
 * handle errors and unusual events first, separate function
 * to improve cache hits for fast path interrupt handling
 */
static noinline void unlikely_6120_intr(struct qib_devdata *dd, u64 istat)
{
        if (unlikely(istat & ~QLOGIC_IB_I_BITSEXTANT))
                qib_dev_err(dd, "interrupt with unknown interrupts %Lx set\n",
                            istat & ~QLOGIC_IB_I_BITSEXTANT);

        if (istat & QLOGIC_IB_I_ERROR) {
                u64 estat = 0;

                qib_stats.sps_errints++;
                estat = qib_read_kreg64(dd, kr_errstatus);
                if (!estat)
                        qib_devinfo(dd->pcidev,
                                "error interrupt (%Lx), but no error bits set!\n",
                                istat);
                handle_6120_errors(dd, estat);
        }

        if (istat & QLOGIC_IB_I_GPIO) {
                u32 gpiostatus;
                u32 to_clear = 0;

                /*
                 * GPIO_3..5 on IBA6120 Rev2 chips indicate
                 * errors that we need to count.
                 */
                gpiostatus = qib_read_kreg32(dd, kr_gpio_status);
                /* First the error-counter case. */
                if (gpiostatus & GPIO_ERRINTR_MASK) {
                        /* want to clear the bits we see asserted. */
                        to_clear |= (gpiostatus & GPIO_ERRINTR_MASK);

                        /*
                         * Count appropriately, clear bits out of our copy,
                         * as they have been "handled".
                         */
                        if (gpiostatus & (1 << GPIO_RXUVL_BIT))
                                dd->cspec->rxfc_unsupvl_errs++;
                        if (gpiostatus & (1 << GPIO_OVRUN_BIT))
                                dd->cspec->overrun_thresh_errs++;
                        if (gpiostatus & (1 << GPIO_LLI_BIT))
                                dd->cspec->lli_errs++;
                        gpiostatus &= ~GPIO_ERRINTR_MASK;
                }
                if (gpiostatus) {
                        /*
                         * Some unexpected bits remain. If they could have
                         * caused the interrupt, complain and clear.
                         * To avoid repetition of this condition, also clear
                         * the mask. It is almost certainly due to error.
                         */
                        const u32 mask = qib_read_kreg32(dd, kr_gpio_mask);

                        /*
                         * Also check that the chip reflects our shadow,
                         * and report issues, If they caused the interrupt.
                         * we will suppress by refreshing from the shadow.
                         */
                        if (mask & gpiostatus) {
                                to_clear |= (gpiostatus & mask);
                                dd->cspec->gpio_mask &= ~(gpiostatus & mask);
                                qib_write_kreg(dd, kr_gpio_mask,
                                               dd->cspec->gpio_mask);
                        }
                }
                if (to_clear)
                        qib_write_kreg(dd, kr_gpio_clear, (u64) to_clear);
        }
}

static irqreturn_t qib_6120intr(int irq, void *data)
{
        struct qib_devdata *dd = data;
        irqreturn_t ret;
        u32 istat, ctxtrbits, rmask, crcs = 0;
        unsigned i;

        if ((dd->flags & (QIB_PRESENT | QIB_BADINTR)) != QIB_PRESENT) {
                /*
                 * This return value is not great, but we do not want the
                 * interrupt core code to remove our interrupt handler
                 * because we don't appear to be handling an interrupt
                 * during a chip reset.
                 */
                ret = IRQ_HANDLED;
                goto bail;
        }

        istat = qib_read_kreg32(dd, kr_intstatus);

        if (unlikely(!istat)) {
                ret = IRQ_NONE; /* not our interrupt, or already handled */
                goto bail;
        }
        if (unlikely(istat == -1)) {
                qib_bad_intrstatus(dd);
                /* don't know if it was our interrupt or not */
                ret = IRQ_NONE;
                goto bail;
        }

        this_cpu_inc(*dd->int_counter);

        if (unlikely(istat & (~QLOGIC_IB_I_BITSEXTANT |
                              QLOGIC_IB_I_GPIO | QLOGIC_IB_I_ERROR)))
                unlikely_6120_intr(dd, istat);

        /*
         * Clear the interrupt bits we found set, relatively early, so we
         * "know" know the chip will have seen this by the time we process
         * the queue, and will re-interrupt if necessary.  The processor
         * itself won't take the interrupt again until we return.
         */
        qib_write_kreg(dd, kr_intclear, istat);

        /*
         * Handle kernel receive queues before checking for pio buffers
         * available since receives can overflow; piobuf waiters can afford
         * a few extra cycles, since they were waiting anyway.
         */
        ctxtrbits = istat &
                ((QLOGIC_IB_I_RCVAVAIL_MASK << QLOGIC_IB_I_RCVAVAIL_SHIFT) |
                 (QLOGIC_IB_I_RCVURG_MASK << QLOGIC_IB_I_RCVURG_SHIFT));
        if (ctxtrbits) {
                rmask = (1U << QLOGIC_IB_I_RCVAVAIL_SHIFT) |
                        (1U << QLOGIC_IB_I_RCVURG_SHIFT);
                for (i = 0; i < dd->first_user_ctxt; i++) {
                        if (ctxtrbits & rmask) {
                                ctxtrbits &= ~rmask;
                                crcs += qib_kreceive(dd->rcd[i],
                                                     &dd->cspec->lli_counter,
                                                     NULL);
                        }
                        rmask <<= 1;
                }
                if (crcs) {
                        u32 cntr = dd->cspec->lli_counter;

                        cntr += crcs;
                        if (cntr) {
                                if (cntr > dd->cspec->lli_thresh) {
                                        dd->cspec->lli_counter = 0;
                                        dd->cspec->lli_errs++;
                                } else
                                        dd->cspec->lli_counter += cntr;
                        }
                }


                if (ctxtrbits) {
                        ctxtrbits =
                                (ctxtrbits >> QLOGIC_IB_I_RCVAVAIL_SHIFT) |
                                (ctxtrbits >> QLOGIC_IB_I_RCVURG_SHIFT);
                        qib_handle_urcv(dd, ctxtrbits);
                }
        }

        if ((istat & QLOGIC_IB_I_SPIOBUFAVAIL) && (dd->flags & QIB_INITTED))
                qib_ib_piobufavail(dd);

        ret = IRQ_HANDLED;
bail:
        return ret;
}

/*
 * Set up our chip-specific interrupt handler
 * The interrupt type has already been setup, so
 * we just need to do the registration and error checking.
 */
static void qib_setup_6120_interrupt(struct qib_devdata *dd)
{
        /*
         * If the chip supports added error indication via GPIO pins,
         * enable interrupts on those bits so the interrupt routine
         * can count the events. Also set flag so interrupt routine
         * can know they are expected.
         */
        if (SYM_FIELD(dd->revision, Revision_R,
                      ChipRevMinor) > 1) {
                /* Rev2+ reports extra errors via internal GPIO pins */
                dd->cspec->gpio_mask |= GPIO_ERRINTR_MASK;
                qib_write_kreg(dd, kr_gpio_mask, dd->cspec->gpio_mask);
        }

        if (!dd->cspec->irq)
                qib_dev_err(dd,
                        "irq is 0, BIOS error?  Interrupts won't work\n");
        else {
                int ret;

                ret = request_irq(dd->cspec->irq, qib_6120intr, 0,
                                  QIB_DRV_NAME, dd);
                if (ret)
                        qib_dev_err(dd,
                                "Couldn't setup interrupt (irq=%d): %d\n",
                                dd->cspec->irq, ret);
        }
}

/**
 * pe_boardname - fill in the board name
 * @dd: the qlogic_ib device
 *
 * info is based on the board revision register
 */
static void pe_boardname(struct qib_devdata *dd)
{
        char *n;
        u32 boardid, namelen;

        boardid = SYM_FIELD(dd->revision, Revision,
                            BoardID);

        switch (boardid) {
        case 2:
                n = "InfiniPath_QLE7140";
                break;
        default:
                qib_dev_err(dd, "Unknown 6120 board with ID %u\n", boardid);
                n = "Unknown_InfiniPath_6120";
                break;
        }
        namelen = strlen(n) + 1;
        dd->boardname = kmalloc(namelen, GFP_KERNEL);
        if (!dd->boardname)
                qib_dev_err(dd, "Failed allocation for board name: %s\n", n);
        else
                snprintf(dd->boardname, namelen, "%s", n);

        if (dd->majrev != 4 || !dd->minrev || dd->minrev > 2)
                qib_dev_err(dd,
                        "Unsupported InfiniPath hardware revision %u.%u!\n",
                        dd->majrev, dd->minrev);

        snprintf(dd->boardversion, sizeof(dd->boardversion),
                 "ChipABI %u.%u, %s, InfiniPath%u %u.%u, SW Compat %u\n",
                 QIB_CHIP_VERS_MAJ, QIB_CHIP_VERS_MIN, dd->boardname,
                 (unsigned)SYM_FIELD(dd->revision, Revision_R, Arch),
                 dd->majrev, dd->minrev,
                 (unsigned)SYM_FIELD(dd->revision, Revision_R, SW));

}

/*
 * This routine sleeps, so it can only be called from user context, not
 * from interrupt context.  If we need interrupt context, we can split
 * it into two routines.
 */
static int qib_6120_setup_reset(struct qib_devdata *dd)
{
        u64 val;
        int i;
        int ret;
        u16 cmdval;
        u8 int_line, clinesz;

        qib_pcie_getcmd(dd, &cmdval, &int_line, &clinesz);

        /* Use ERROR so it shows up in logs, etc. */
        qib_dev_err(dd, "Resetting InfiniPath unit %u\n", dd->unit);

        /* no interrupts till re-initted */
        qib_6120_set_intr_state(dd, 0);

        dd->cspec->ibdeltainprog = 0;
        dd->cspec->ibsymdelta = 0;
        dd->cspec->iblnkerrdelta = 0;

        /*
         * Keep chip from being accessed until we are ready.  Use
         * writeq() directly, to allow the write even though QIB_PRESENT
         * isn't set.
         */
        dd->flags &= ~(QIB_INITTED | QIB_PRESENT);
        /* so we check interrupts work again */
        dd->z_int_counter = qib_int_counter(dd);
        val = dd->control | QLOGIC_IB_C_RESET;
        writeq(val, &dd->kregbase[kr_control]);
        mb(); /* prevent compiler re-ordering around actual reset */

        for (i = 1; i <= 5; i++) {
                /*
                 * Allow MBIST, etc. to complete; longer on each retry.
                 * We sometimes get machine checks from bus timeout if no
                 * response, so for now, make it *really* long.
                 */
                msleep(1000 + (1 + i) * 2000);

                qib_pcie_reenable(dd, cmdval, int_line, clinesz);

                /*
                 * Use readq directly, so we don't need to mark it as PRESENT
                 * until we get a successful indication that all is well.
                 */
                val = readq(&dd->kregbase[kr_revision]);
                if (val == dd->revision) {
                        dd->flags |= QIB_PRESENT; /* it's back */
                        ret = qib_reinit_intr(dd);
                        goto bail;
                }
        }
        ret = 0; /* failed */

bail:
        if (ret) {
                if (qib_pcie_params(dd, dd->lbus_width, NULL, NULL))
                        qib_dev_err(dd,
                                "Reset failed to setup PCIe or interrupts; continuing anyway\n");
                /* clear the reset error, init error/hwerror mask */
                qib_6120_init_hwerrors(dd);
                /* for Rev2 error interrupts; nop for rev 1 */
                qib_write_kreg(dd, kr_gpio_mask, dd->cspec->gpio_mask);
                /* clear the reset error, init error/hwerror mask */
                qib_6120_init_hwerrors(dd);
        }
        return ret;
}

/**
 * qib_6120_put_tid - write a TID in chip
 * @dd: the qlogic_ib device
 * @tidptr: pointer to the expected TID (in chip) to update
 * @tidtype: RCVHQ_RCV_TYPE_EAGER (1) for eager, RCVHQ_RCV_TYPE_EXPECTED (0)
 * for expected
 * @pa: physical address of in memory buffer; tidinvalid if freeing
 *
 * This exists as a separate routine to allow for special locking etc.
 * It's used for both the full cleanup on exit, as well as the normal
 * setup and teardown.
 */
static void qib_6120_put_tid(struct qib_devdata *dd, u64 __iomem *tidptr,
                             u32 type, unsigned long pa)
{
        u32 __iomem *tidp32 = (u32 __iomem *)tidptr;
        unsigned long flags;
        int tidx;
        spinlock_t *tidlockp; /* select appropriate spinlock */

        if (!dd->kregbase)
                return;

        if (pa != dd->tidinvalid) {
                if (pa & ((1U << 11) - 1)) {
                        qib_dev_err(dd, "Physaddr %lx not 2KB aligned!\n",
                                    pa);
                        return;
                }
                pa >>= 11;
                if (pa & ~QLOGIC_IB_RT_ADDR_MASK) {
                        qib_dev_err(dd,
                                "Physical page address 0x%lx larger than supported\n",
                                pa);
                        return;
                }

                if (type == RCVHQ_RCV_TYPE_EAGER)
                        pa |= dd->tidtemplate;
                else /* for now, always full 4KB page */
                        pa |= 2 << 29;
        }

        /*
         * Avoid chip issue by writing the scratch register
         * before and after the TID, and with an io write barrier.
         * We use a spinlock around the writes, so they can't intermix
         * with other TID (eager or expected) writes (the chip problem
         * is triggered by back to back TID writes). Unfortunately, this
         * call can be done from interrupt level for the ctxt 0 eager TIDs,
         * so we have to use irqsave locks.
         */
        /*
         * Assumes tidptr always > egrtidbase
         * if type == RCVHQ_RCV_TYPE_EAGER.
         */
        tidx = tidptr - dd->egrtidbase;

        tidlockp = (type == RCVHQ_RCV_TYPE_EAGER && tidx < dd->rcvhdrcnt)
                ? &dd->cspec->kernel_tid_lock : &dd->cspec->user_tid_lock;
        spin_lock_irqsave(tidlockp, flags);
        qib_write_kreg(dd, kr_scratch, 0xfeeddeaf);
        writel(pa, tidp32);
        qib_write_kreg(dd, kr_scratch, 0xdeadbeef);
        mmiowb();
        spin_unlock_irqrestore(tidlockp, flags);
}

/**
 * qib_6120_put_tid_2 - write a TID in chip, Revision 2 or higher
 * @dd: the qlogic_ib device
 * @tidptr: pointer to the expected TID (in chip) to update
 * @tidtype: RCVHQ_RCV_TYPE_EAGER (1) for eager, RCVHQ_RCV_TYPE_EXPECTED (0)
 * for expected
 * @pa: physical address of in memory buffer; tidinvalid if freeing
 *
 * This exists as a separate routine to allow for selection of the
 * appropriate "flavor". The static calls in cleanup just use the
 * revision-agnostic form, as they are not performance critical.
 */
static void qib_6120_put_tid_2(struct qib_devdata *dd, u64 __iomem *tidptr,
                               u32 type, unsigned long pa)
{
        u32 __iomem *tidp32 = (u32 __iomem *)tidptr;
        u32 tidx;

        if (!dd->kregbase)
                return;

        if (pa != dd->tidinvalid) {
                if (pa & ((1U << 11) - 1)) {
                        qib_dev_err(dd, "Physaddr %lx not 2KB aligned!\n",
                                    pa);
                        return;
                }
                pa >>= 11;
                if (pa & ~QLOGIC_IB_RT_ADDR_MASK) {
                        qib_dev_err(dd,
                                "Physical page address 0x%lx larger than supported\n",
                                pa);
                        return;
                }

                if (type == RCVHQ_RCV_TYPE_EAGER)
                        pa |= dd->tidtemplate;
                else /* for now, always full 4KB page */
                        pa |= 2 << 29;
        }
        tidx = tidptr - dd->egrtidbase;
        writel(pa, tidp32);
        mmiowb();
}


/**
 * qib_6120_clear_tids - clear all TID entries for a context, expected and eager
 * @dd: the qlogic_ib device
 * @ctxt: the context
 *
 * clear all TID entries for a context, expected and eager.
 * Used from qib_close().  On this chip, TIDs are only 32 bits,
 * not 64, but they are still on 64 bit boundaries, so tidbase
 * is declared as u64 * for the pointer math, even though we write 32 bits
 */
static void qib_6120_clear_tids(struct qib_devdata *dd,
                                struct qib_ctxtdata *rcd)
{
        u64 __iomem *tidbase;
        unsigned long tidinv;
        u32 ctxt;
        int i;

        if (!dd->kregbase || !rcd)
                return;

        ctxt = rcd->ctxt;

        tidinv = dd->tidinvalid;
        tidbase = (u64 __iomem *)
                ((char __iomem *)(dd->kregbase) +
                 dd->rcvtidbase +
                 ctxt * dd->rcvtidcnt * sizeof(*tidbase));

        for (i = 0; i < dd->rcvtidcnt; i++)
                /* use func pointer because could be one of two funcs */
                dd->f_put_tid(dd, &tidbase[i], RCVHQ_RCV_TYPE_EXPECTED,
                                  tidinv);

        tidbase = (u64 __iomem *)
                ((char __iomem *)(dd->kregbase) +
                 dd->rcvegrbase +
                 rcd->rcvegr_tid_base * sizeof(*tidbase));

        for (i = 0; i < rcd->rcvegrcnt; i++)
                /* use func pointer because could be one of two funcs */
                dd->f_put_tid(dd, &tidbase[i], RCVHQ_RCV_TYPE_EAGER,
                                  tidinv);
}

/**
 * qib_6120_tidtemplate - setup constants for TID updates
 * @dd: the qlogic_ib device
 *
 * We setup stuff that we use a lot, to avoid calculating each time
 */
static void qib_6120_tidtemplate(struct qib_devdata *dd)
{
        u32 egrsize = dd->rcvegrbufsize;

        /*
         * For now, we always allocate 4KB buffers (at init) so we can
         * receive max size packets.  We may want a module parameter to
         * specify 2KB or 4KB and/or make be per ctxt instead of per device
         * for those who want to reduce memory footprint.  Note that the
         * rcvhdrentsize size must be large enough to hold the largest
         * IB header (currently 96 bytes) that we expect to handle (plus of
         * course the 2 dwords of RHF).
         */
        if (egrsize == 2048)
                dd->tidtemplate = 1U << 29;
        else if (egrsize == 4096)
                dd->tidtemplate = 2U << 29;
        dd->tidinvalid = 0;
}

int __attribute__((weak)) qib_unordered_wc(void)
{
        return 0;
}

/**
 * qib_6120_get_base_info - set chip-specific flags for user code
 * @rcd: the qlogic_ib ctxt
 * @kbase: qib_base_info pointer
 *
 * We set the PCIE flag because the lower bandwidth on PCIe vs
 * HyperTransport can affect some user packet algorithms.
 */
static int qib_6120_get_base_info(struct qib_ctxtdata *rcd,
                                  struct qib_base_info *kinfo)
{
        if (qib_unordered_wc())
                kinfo->spi_runtime_flags |= QIB_RUNTIME_FORCE_WC_ORDER;

        kinfo->spi_runtime_flags |= QIB_RUNTIME_PCIE |
                QIB_RUNTIME_FORCE_PIOAVAIL | QIB_RUNTIME_PIO_REGSWAPPED;
        return 0;
}


static struct qib_message_header *
qib_6120_get_msgheader(struct qib_devdata *dd, __le32 *rhf_addr)
{
        return (struct qib_message_header *)
                &rhf_addr[sizeof(u64) / sizeof(u32)];
}

static void qib_6120_config_ctxts(struct qib_devdata *dd)
{
        dd->ctxtcnt = qib_read_kreg32(dd, kr_portcnt);
        if (qib_n_krcv_queues > 1) {
                dd->first_user_ctxt = qib_n_krcv_queues * dd->num_pports;
                if (dd->first_user_ctxt > dd->ctxtcnt)
                        dd->first_user_ctxt = dd->ctxtcnt;
                dd->qpn_mask = dd->first_user_ctxt <= 2 ? 2 : 6;
        } else
                dd->first_user_ctxt = dd->num_pports;
        dd->n_krcv_queues = dd->first_user_ctxt;
}

static void qib_update_6120_usrhead(struct qib_ctxtdata *rcd, u64 hd,
                                    u32 updegr, u32 egrhd, u32 npkts)
{
        if (updegr)
                qib_write_ureg(rcd->dd, ur_rcvegrindexhead, egrhd, rcd->ctxt);
        mmiowb();
        qib_write_ureg(rcd->dd, ur_rcvhdrhead, hd, rcd->ctxt);
        mmiowb();
}

static u32 qib_6120_hdrqempty(struct qib_ctxtdata *rcd)
{
        u32 head, tail;

        head = qib_read_ureg32(rcd->dd, ur_rcvhdrhead, rcd->ctxt);
        if (rcd->rcvhdrtail_kvaddr)
                tail = qib_get_rcvhdrtail(rcd);
        else
                tail = qib_read_ureg32(rcd->dd, ur_rcvhdrtail, rcd->ctxt);
        return head == tail;
}

/*
 * Used when we close any ctxt, for DMA already in flight
 * at close.  Can't be done until we know hdrq size, so not
 * early in chip init.
 */
static void alloc_dummy_hdrq(struct qib_devdata *dd)
{
        dd->cspec->dummy_hdrq = dma_alloc_coherent(&dd->pcidev->dev,
                                        dd->rcd[0]->rcvhdrq_size,
                                        &dd->cspec->dummy_hdrq_phys,
                                        GFP_ATOMIC | __GFP_COMP);
        if (!dd->cspec->dummy_hdrq) {
                qib_devinfo(dd->pcidev, "Couldn't allocate dummy hdrq\n");
                /* fallback to just 0'ing */
                dd->cspec->dummy_hdrq_phys = 0UL;
        }
}

/*
 * Modify the RCVCTRL register in chip-specific way. This
 * is a function because bit positions and (future) register
 * location is chip-specific, but the needed operations are
 * generic. <op> is a bit-mask because we often want to
 * do multiple modifications.
 */
static void rcvctrl_6120_mod(struct qib_pportdata *ppd, unsigned int op,
                             int ctxt)
{
        struct qib_devdata *dd = ppd->dd;
        u64 mask, val;
        unsigned long flags;

        spin_lock_irqsave(&dd->cspec->rcvmod_lock, flags);

        if (op & QIB_RCVCTRL_TAILUPD_ENB)
                dd->rcvctrl |= (1ULL << QLOGIC_IB_R_TAILUPD_SHIFT);
        if (op & QIB_RCVCTRL_TAILUPD_DIS)
                dd->rcvctrl &= ~(1ULL << QLOGIC_IB_R_TAILUPD_SHIFT);
        if (op & QIB_RCVCTRL_PKEY_ENB)
                dd->rcvctrl &= ~(1ULL << IBA6120_R_PKEY_DIS_SHIFT);
        if (op & QIB_RCVCTRL_PKEY_DIS)
                dd->rcvctrl |= (1ULL << IBA6120_R_PKEY_DIS_SHIFT);
        if (ctxt < 0)
                mask = (1ULL << dd->ctxtcnt) - 1;
        else
                mask = (1ULL << ctxt);
        if (op & QIB_RCVCTRL_CTXT_ENB) {
                /* always done for specific ctxt */
                dd->rcvctrl |= (mask << SYM_LSB(RcvCtrl, PortEnable));
                if (!(dd->flags & QIB_NODMA_RTAIL))
                        dd->rcvctrl |= 1ULL << QLOGIC_IB_R_TAILUPD_SHIFT;
                /* Write these registers before the context is enabled. */
                qib_write_kreg_ctxt(dd, kr_rcvhdrtailaddr, ctxt,
                        dd->rcd[ctxt]->rcvhdrqtailaddr_phys);
                qib_write_kreg_ctxt(dd, kr_rcvhdraddr, ctxt,
                        dd->rcd[ctxt]->rcvhdrq_phys);

                if (ctxt == 0 && !dd->cspec->dummy_hdrq)
                        alloc_dummy_hdrq(dd);
        }
        if (op & QIB_RCVCTRL_CTXT_DIS)
                dd->rcvctrl &= ~(mask << SYM_LSB(RcvCtrl, PortEnable));
        if (op & QIB_RCVCTRL_INTRAVAIL_ENB)
                dd->rcvctrl |= (mask << QLOGIC_IB_R_INTRAVAIL_SHIFT);
        if (op & QIB_RCVCTRL_INTRAVAIL_DIS)
                dd->rcvctrl &= ~(mask << QLOGIC_IB_R_INTRAVAIL_SHIFT);
        qib_write_kreg(dd, kr_rcvctrl, dd->rcvctrl);
        if ((op & QIB_RCVCTRL_INTRAVAIL_ENB) && dd->rhdrhead_intr_off) {
                /* arm rcv interrupt */
                val = qib_read_ureg32(dd, ur_rcvhdrhead, ctxt) |
                        dd->rhdrhead_intr_off;
                qib_write_ureg(dd, ur_rcvhdrhead, val, ctxt);
        }
        if (op & QIB_RCVCTRL_CTXT_ENB) {
                /*
                 * Init the context registers also; if we were
                 * disabled, tail and head should both be zero
                 * already from the enable, but since we don't
                 * know, we have to do it explicitly.
                 */
                val = qib_read_ureg32(dd, ur_rcvegrindextail, ctxt);
                qib_write_ureg(dd, ur_rcvegrindexhead, val, ctxt);

                val = qib_read_ureg32(dd, ur_rcvhdrtail, ctxt);
                dd->rcd[ctxt]->head = val;
                /* If kctxt, interrupt on next receive. */
                if (ctxt < dd->first_user_ctxt)
                        val |= dd->rhdrhead_intr_off;
                qib_write_ureg(dd, ur_rcvhdrhead, val, ctxt);
        }
        if (op & QIB_RCVCTRL_CTXT_DIS) {
                /*
                 * Be paranoid, and never write 0's to these, just use an
                 * unused page.  Of course,
                 * rcvhdraddr points to a large chunk of memory, so this
                 * could still trash things, but at least it won't trash
                 * page 0, and by disabling the ctxt, it should stop "soon",
                 * even if a packet or two is in already in flight after we
                 * disabled the ctxt.  Only 6120 has this issue.
                 */
                if (ctxt >= 0) {
                        qib_write_kreg_ctxt(dd, kr_rcvhdrtailaddr, ctxt,
                                            dd->cspec->dummy_hdrq_phys);
                        qib_write_kreg_ctxt(dd, kr_rcvhdraddr, ctxt,
                                            dd->cspec->dummy_hdrq_phys);
                } else {
                        unsigned i;

                        for (i = 0; i < dd->cfgctxts; i++) {
                                qib_write_kreg_ctxt(dd, kr_rcvhdrtailaddr,
                                            i, dd->cspec->dummy_hdrq_phys);
                                qib_write_kreg_ctxt(dd, kr_rcvhdraddr,
                                            i, dd->cspec->dummy_hdrq_phys);
                        }
                }
        }
        spin_unlock_irqrestore(&dd->cspec->rcvmod_lock, flags);
}

/*
 * Modify the SENDCTRL register in chip-specific way. This
 * is a function there may be multiple such registers with
 * slightly different layouts. Only operations actually used
 * are implemented yet.
 * Chip requires no back-back sendctrl writes, so write
 * scratch register after writing sendctrl
 */
static void sendctrl_6120_mod(struct qib_pportdata *ppd, u32 op)
{
        struct qib_devdata *dd = ppd->dd;
        u64 tmp_dd_sendctrl;
        unsigned long flags;

        spin_lock_irqsave(&dd->sendctrl_lock, flags);

        /* First the ones that are "sticky", saved in shadow */
        if (op & QIB_SENDCTRL_CLEAR)
                dd->sendctrl = 0;
        if (op & QIB_SENDCTRL_SEND_DIS)
                dd->sendctrl &= ~SYM_MASK(SendCtrl, PIOEnable);
        else if (op & QIB_SENDCTRL_SEND_ENB)
                dd->sendctrl |= SYM_MASK(SendCtrl, PIOEnable);
        if (op & QIB_SENDCTRL_AVAIL_DIS)
                dd->sendctrl &= ~SYM_MASK(SendCtrl, PIOBufAvailUpd);
        else if (op & QIB_SENDCTRL_AVAIL_ENB)
                dd->sendctrl |= SYM_MASK(SendCtrl, PIOBufAvailUpd);

        if (op & QIB_SENDCTRL_DISARM_ALL) {
                u32 i, last;

                tmp_dd_sendctrl = dd->sendctrl;
                /*
                 * disarm any that are not yet launched, disabling sends
                 * and updates until done.
                 */
                last = dd->piobcnt2k + dd->piobcnt4k;
                tmp_dd_sendctrl &=
                        ~(SYM_MASK(SendCtrl, PIOEnable) |
                          SYM_MASK(SendCtrl, PIOBufAvailUpd));
                for (i = 0; i < last; i++) {
                        qib_write_kreg(dd, kr_sendctrl, tmp_dd_sendctrl |
                                       SYM_MASK(SendCtrl, Disarm) | i);
                        qib_write_kreg(dd, kr_scratch, 0);
                }
        }

        tmp_dd_sendctrl = dd->sendctrl;

        if (op & QIB_SENDCTRL_FLUSH)
                tmp_dd_sendctrl |= SYM_MASK(SendCtrl, Abort);
        if (op & QIB_SENDCTRL_DISARM)
                tmp_dd_sendctrl |= SYM_MASK(SendCtrl, Disarm) |
                        ((op & QIB_6120_SendCtrl_DisarmPIOBuf_RMASK) <<
                         SYM_LSB(SendCtrl, DisarmPIOBuf));
        if (op & QIB_SENDCTRL_AVAIL_BLIP)
                tmp_dd_sendctrl &= ~SYM_MASK(SendCtrl, PIOBufAvailUpd);

        qib_write_kreg(dd, kr_sendctrl, tmp_dd_sendctrl);
        qib_write_kreg(dd, kr_scratch, 0);

        if (op & QIB_SENDCTRL_AVAIL_BLIP) {
                qib_write_kreg(dd, kr_sendctrl, dd->sendctrl);
                qib_write_kreg(dd, kr_scratch, 0);
        }

        spin_unlock_irqrestore(&dd->sendctrl_lock, flags);

        if (op & QIB_SENDCTRL_FLUSH) {
                u32 v;
                /*
                 * ensure writes have hit chip, then do a few
                 * more reads, to allow DMA of pioavail registers
                 * to occur, so in-memory copy is in sync with
                 * the chip.  Not always safe to sleep.
                 */
                v = qib_read_kreg32(dd, kr_scratch);
                qib_write_kreg(dd, kr_scratch, v);
                v = qib_read_kreg32(dd, kr_scratch);
                qib_write_kreg(dd, kr_scratch, v);
                qib_read_kreg32(dd, kr_scratch);
        }
}

/**
 * qib_portcntr_6120 - read a per-port counter
 * @dd: the qlogic_ib device
 * @creg: the counter to snapshot
 */
static u64 qib_portcntr_6120(struct qib_pportdata *ppd, u32 reg)
{
        u64 ret = 0ULL;
        struct qib_devdata *dd = ppd->dd;
        u16 creg;
        /* 0xffff for unimplemented or synthesized counters */
        static const u16 xlator[] = {
                [QIBPORTCNTR_PKTSEND] = cr_pktsend,
                [QIBPORTCNTR_WORDSEND] = cr_wordsend,
                [QIBPORTCNTR_PSXMITDATA] = 0xffff,
                [QIBPORTCNTR_PSXMITPKTS] = 0xffff,
                [QIBPORTCNTR_PSXMITWAIT] = 0xffff,
                [QIBPORTCNTR_SENDSTALL] = cr_sendstall,
                [QIBPORTCNTR_PKTRCV] = cr_pktrcv,
                [QIBPORTCNTR_PSRCVDATA] = 0xffff,
                [QIBPORTCNTR_PSRCVPKTS] = 0xffff,
                [QIBPORTCNTR_RCVEBP] = cr_rcvebp,
                [QIBPORTCNTR_RCVOVFL] = cr_rcvovfl,
                [QIBPORTCNTR_WORDRCV] = cr_wordrcv,
                [QIBPORTCNTR_RXDROPPKT] = cr_rxdroppkt,
                [QIBPORTCNTR_RXLOCALPHYERR] = 0xffff,
                [QIBPORTCNTR_RXVLERR] = 0xffff,
                [QIBPORTCNTR_ERRICRC] = cr_erricrc,
                [QIBPORTCNTR_ERRVCRC] = cr_errvcrc,
                [QIBPORTCNTR_ERRLPCRC] = cr_errlpcrc,
                [QIBPORTCNTR_BADFORMAT] = cr_badformat,
                [QIBPORTCNTR_ERR_RLEN] = cr_err_rlen,
                [QIBPORTCNTR_IBSYMBOLERR] = cr_ibsymbolerr,
                [QIBPORTCNTR_INVALIDRLEN] = cr_invalidrlen,
                [QIBPORTCNTR_UNSUPVL] = cr_txunsupvl,
                [QIBPORTCNTR_EXCESSBUFOVFL] = 0xffff,
                [QIBPORTCNTR_ERRLINK] = cr_errlink,
                [QIBPORTCNTR_IBLINKDOWN] = cr_iblinkdown,
                [QIBPORTCNTR_IBLINKERRRECOV] = cr_iblinkerrrecov,
                [QIBPORTCNTR_LLI] = 0xffff,
                [QIBPORTCNTR_PSINTERVAL] = 0xffff,
                [QIBPORTCNTR_PSSTART] = 0xffff,
                [QIBPORTCNTR_PSSTAT] = 0xffff,
                [QIBPORTCNTR_VL15PKTDROP] = 0xffff,
                [QIBPORTCNTR_ERRPKEY] = cr_errpkey,
                [QIBPORTCNTR_KHDROVFL] = 0xffff,
        };

        if (reg >= ARRAY_SIZE(xlator)) {
                qib_devinfo(ppd->dd->pcidev,
                         "Unimplemented portcounter %u\n", reg);
                goto done;
        }
        creg = xlator[reg];

        /* handle counters requests not implemented as chip counters */
        if (reg == QIBPORTCNTR_LLI)
                ret = dd->cspec->lli_errs;
        else if (reg == QIBPORTCNTR_EXCESSBUFOVFL)
                ret = dd->cspec->overrun_thresh_errs;
        else if (reg == QIBPORTCNTR_KHDROVFL) {
                int i;

                /* sum over all kernel contexts */
                for (i = 0; i < dd->first_user_ctxt; i++)
                        ret += read_6120_creg32(dd, cr_portovfl + i);
        } else if (reg == QIBPORTCNTR_PSSTAT)
                ret = dd->cspec->pma_sample_status;
        if (creg == 0xffff)
                goto done;

        /*
         * only fast incrementing counters are 64bit; use 32 bit reads to
         * avoid two independent reads when on opteron
         */
        if (creg == cr_wordsend || creg == cr_wordrcv ||
            creg == cr_pktsend || creg == cr_pktrcv)
                ret = read_6120_creg(dd, creg);
        else
                ret = read_6120_creg32(dd, creg);
        if (creg == cr_ibsymbolerr) {
                if (dd->cspec->ibdeltainprog)
                        ret -= ret - dd->cspec->ibsymsnap;
                ret -= dd->cspec->ibsymdelta;
        } else if (creg == cr_iblinkerrrecov) {
                if (dd->cspec->ibdeltainprog)
                        ret -= ret - dd->cspec->iblnkerrsnap;
                ret -= dd->cspec->iblnkerrdelta;
        }
        if (reg == QIBPORTCNTR_RXDROPPKT) /* add special cased count */
                ret += dd->cspec->rxfc_unsupvl_errs;

done:
        return ret;
}

/*
 * Device counter names (not port-specific), one line per stat,
 * single string.  Used by utilities like ipathstats to print the stats
 * in a way which works for different versions of drivers, without changing
 * the utility.  Names need to be 12 chars or less (w/o newline), for proper
 * display by utility.
 * Non-error counters are first.
 * Start of "error" conters is indicated by a leading "E " on the first
 * "error" counter, and doesn't count in label length.
 * The EgrOvfl list needs to be last so we truncate them at the configured
 * context count for the device.
 * cntr6120indices contains the corresponding register indices.
 */
static const char cntr6120names[] =
        "Interrupts\n"
        "HostBusStall\n"
        "E RxTIDFull\n"
        "RxTIDInvalid\n"
        "Ctxt0EgrOvfl\n"
        "Ctxt1EgrOvfl\n"
        "Ctxt2EgrOvfl\n"
        "Ctxt3EgrOvfl\n"
        "Ctxt4EgrOvfl\n";

static const size_t cntr6120indices[] = {
        cr_lbint,
        cr_lbflowstall,
        cr_errtidfull,
        cr_errtidvalid,
        cr_portovfl + 0,
        cr_portovfl + 1,
        cr_portovfl + 2,
        cr_portovfl + 3,
        cr_portovfl + 4,
};

/*
 * same as cntr6120names and cntr6120indices, but for port-specific counters.
 * portcntr6120indices is somewhat complicated by some registers needing
 * adjustments of various kinds, and those are ORed with _PORT_VIRT_FLAG
 */
static const char portcntr6120names[] =
        "TxPkt\n"
        "TxFlowPkt\n"
        "TxWords\n"
        "RxPkt\n"
        "RxFlowPkt\n"
        "RxWords\n"
        "TxFlowStall\n"
        "E IBStatusChng\n"
        "IBLinkDown\n"
        "IBLnkRecov\n"
        "IBRxLinkErr\n"
        "IBSymbolErr\n"
        "RxLLIErr\n"
        "RxBadFormat\n"
        "RxBadLen\n"
        "RxBufOvrfl\n"
        "RxEBP\n"
        "RxFlowCtlErr\n"
        "RxICRCerr\n"
        "RxLPCRCerr\n"
        "RxVCRCerr\n"
        "RxInvalLen\n"
        "RxInvalPKey\n"
        "RxPktDropped\n"
        "TxBadLength\n"
        "TxDropped\n"
        "TxInvalLen\n"
        "TxUnderrun\n"
        "TxUnsupVL\n"
        ;

#define _PORT_VIRT_FLAG 0x8000 /* "virtual", need adjustments */
static const size_t portcntr6120indices[] = {
        QIBPORTCNTR_PKTSEND | _PORT_VIRT_FLAG,
        cr_pktsendflow,
        QIBPORTCNTR_WORDSEND | _PORT_VIRT_FLAG,
        QIBPORTCNTR_PKTRCV | _PORT_VIRT_FLAG,
        cr_pktrcvflowctrl,
        QIBPORTCNTR_WORDRCV | _PORT_VIRT_FLAG,
        QIBPORTCNTR_SENDSTALL | _PORT_VIRT_FLAG,
        cr_ibstatuschange,
        QIBPORTCNTR_IBLINKDOWN | _PORT_VIRT_FLAG,
        QIBPORTCNTR_IBLINKERRRECOV | _PORT_VIRT_FLAG,
        QIBPORTCNTR_ERRLINK | _PORT_VIRT_FLAG,
        QIBPORTCNTR_IBSYMBOLERR | _PORT_VIRT_FLAG,
        QIBPORTCNTR_LLI | _PORT_VIRT_FLAG,
        QIBPORTCNTR_BADFORMAT | _PORT_VIRT_FLAG,
        QIBPORTCNTR_ERR_RLEN | _PORT_VIRT_FLAG,
        QIBPORTCNTR_RCVOVFL | _PORT_VIRT_FLAG,
        QIBPORTCNTR_RCVEBP | _PORT_VIRT_FLAG,
        cr_rcvflowctrl_err,
        QIBPORTCNTR_ERRICRC | _PORT_VIRT_FLAG,
        QIBPORTCNTR_ERRLPCRC | _PORT_VIRT_FLAG,
        QIBPORTCNTR_ERRVCRC | _PORT_VIRT_FLAG,
        QIBPORTCNTR_INVALIDRLEN | _PORT_VIRT_FLAG,
        QIBPORTCNTR_ERRPKEY | _PORT_VIRT_FLAG,
        QIBPORTCNTR_RXDROPPKT | _PORT_VIRT_FLAG,
        cr_invalidslen,
        cr_senddropped,
        cr_errslen,
        cr_sendunderrun,
        cr_txunsupvl,
};

/* do all the setup to make the counter reads efficient later */
static void init_6120_cntrnames(struct qib_devdata *dd)
{
        int i, j = 0;
        char *s;

        for (i = 0, s = (char *)cntr6120names; s && j <= dd->cfgctxts;
             i++) {
                /* we always have at least one counter before the egrovfl */
                if (!j && !strncmp("Ctxt0EgrOvfl", s + 1, 12))
                        j = 1;
                s = strchr(s + 1, '\n');
                if (s && j)
                        j++;
        }
        dd->cspec->ncntrs = i;
        if (!s)
                /* full list; size is without terminating null */
                dd->cspec->cntrnamelen = sizeof(cntr6120names) - 1;
        else
                dd->cspec->cntrnamelen = 1 + s - cntr6120names;
        dd->cspec->cntrs = kmalloc(dd->cspec->ncntrs
                * sizeof(u64), GFP_KERNEL);
        if (!dd->cspec->cntrs)
                qib_dev_err(dd, "Failed allocation for counters\n");

        for (i = 0, s = (char *)portcntr6120names; s; i++)
                s = strchr(s + 1, '\n');
        dd->cspec->nportcntrs = i - 1;
        dd->cspec->portcntrnamelen = sizeof(portcntr6120names) - 1;
        dd->cspec->portcntrs = kmalloc(dd->cspec->nportcntrs
                * sizeof(u64), GFP_KERNEL);
        if (!dd->cspec->portcntrs)
                qib_dev_err(dd, "Failed allocation for portcounters\n");
}

static u32 qib_read_6120cntrs(struct qib_devdata *dd, loff_t pos, char **namep,
                              u64 **cntrp)
{
        u32 ret;

        if (namep) {
                ret = dd->cspec->cntrnamelen;
                if (pos >= ret)
                        ret = 0; /* final read after getting everything */
                else
                        *namep = (char *)cntr6120names;
        } else {
                u64 *cntr = dd->cspec->cntrs;
                int i;

                ret = dd->cspec->ncntrs * sizeof(u64);
                if (!cntr || pos >= ret) {
                        /* everything read, or couldn't get memory */
                        ret = 0;
                        goto done;
                }
                if (pos >= ret) {
                        ret = 0; /* final read after getting everything */
                        goto done;
                }
                *cntrp = cntr;
                for (i = 0; i < dd->cspec->ncntrs; i++)
                        *cntr++ = read_6120_creg32(dd, cntr6120indices[i]);
        }
done:
        return ret;
}

static u32 qib_read_6120portcntrs(struct qib_devdata *dd, loff_t pos, u32 port,
                                  char **namep, u64 **cntrp)
{
        u32 ret;

        if (namep) {
                ret = dd->cspec->portcntrnamelen;
                if (pos >= ret)
                        ret = 0; /* final read after getting everything */
                else
                        *namep = (char *)portcntr6120names;
        } else {
                u64 *cntr = dd->cspec->portcntrs;
                struct qib_pportdata *ppd = &dd->pport[port];
                int i;

                ret = dd->cspec->nportcntrs * sizeof(u64);
                if (!cntr || pos >= ret) {
                        /* everything read, or couldn't get memory */
                        ret = 0;
                        goto done;
                }
                *cntrp = cntr;
                for (i = 0; i < dd->cspec->nportcntrs; i++) {
                        if (portcntr6120indices[i] & _PORT_VIRT_FLAG)
                                *cntr++ = qib_portcntr_6120(ppd,
                                        portcntr6120indices[i] &
                                        ~_PORT_VIRT_FLAG);
                        else
                                *cntr++ = read_6120_creg32(dd,
                                           portcntr6120indices[i]);
                }
        }
done:
        return ret;
}

static void qib_chk_6120_errormask(struct qib_devdata *dd)
{
        static u32 fixed;
        u32 ctrl;
        unsigned long errormask;
        unsigned long hwerrs;

        if (!dd->cspec->errormask || !(dd->flags & QIB_INITTED))
                return;

        errormask = qib_read_kreg64(dd, kr_errmask);

        if (errormask == dd->cspec->errormask)
                return;
        fixed++;

        hwerrs = qib_read_kreg64(dd, kr_hwerrstatus);
        ctrl = qib_read_kreg32(dd, kr_control);

        qib_write_kreg(dd, kr_errmask,
                dd->cspec->errormask);

        if ((hwerrs & dd->cspec->hwerrmask) ||
            (ctrl & QLOGIC_IB_C_FREEZEMODE)) {
                qib_write_kreg(dd, kr_hwerrclear, 0ULL);
                qib_write_kreg(dd, kr_errclear, 0ULL);
                /* force re-interrupt of pending events, just in case */
                qib_write_kreg(dd, kr_intclear, 0ULL);
                qib_devinfo(dd->pcidev,
                         "errormask fixed(%u) %lx->%lx, ctrl %x hwerr %lx\n",
                         fixed, errormask, (unsigned long)dd->cspec->errormask,
                         ctrl, hwerrs);
        }
}

/**
 * qib_get_faststats - get word counters from chip before they overflow
 * @opaque - contains a pointer to the qlogic_ib device qib_devdata
 *
 * This needs more work; in particular, decision on whether we really
 * need traffic_wds done the way it is
 * called from add_timer
 */
static void qib_get_6120_faststats(unsigned long opaque)
{
        struct qib_devdata *dd = (struct qib_devdata *) opaque;
        struct qib_pportdata *ppd = dd->pport;
        unsigned long flags;
        u64 traffic_wds;

        /*
         * don't access the chip while running diags, or memory diags can
         * fail
         */
        if (!(dd->flags & QIB_INITTED) || dd->diag_client)
                /* but re-arm the timer, for diags case; won't hurt other */
                goto done;

        /*
         * We now try to maintain an activity timer, based on traffic
         * exceeding a threshold, so we need to check the word-counts
         * even if they are 64-bit.
         */
        traffic_wds = qib_portcntr_6120(ppd, cr_wordsend) +
                qib_portcntr_6120(ppd, cr_wordrcv);
        spin_lock_irqsave(&dd->eep_st_lock, flags);
        traffic_wds -= dd->traffic_wds;
        dd->traffic_wds += traffic_wds;
        spin_unlock_irqrestore(&dd->eep_st_lock, flags);

        qib_chk_6120_errormask(dd);
done:
        mod_timer(&dd->stats_timer, jiffies + HZ * ACTIVITY_TIMER);
}

/* no interrupt fallback for these chips */
static int qib_6120_nointr_fallback(struct qib_devdata *dd)
{
        return 0;
}

/*
 * reset the XGXS (between serdes and IBC).  Slightly less intrusive
 * than resetting the IBC or external link state, and useful in some
 * cases to cause some retraining.  To do this right, we reset IBC
 * as well.
 */
static void qib_6120_xgxs_reset(struct qib_pportdata *ppd)
{
        u64 val, prev_val;
        struct qib_devdata *dd = ppd->dd;

        prev_val = qib_read_kreg64(dd, kr_xgxs_cfg);
        val = prev_val | QLOGIC_IB_XGXS_RESET;
        prev_val &= ~QLOGIC_IB_XGXS_RESET; /* be sure */
        qib_write_kreg(dd, kr_control,
                       dd->control & ~QLOGIC_IB_C_LINKENABLE);
        qib_write_kreg(dd, kr_xgxs_cfg, val);
        qib_read_kreg32(dd, kr_scratch);
        qib_write_kreg(dd, kr_xgxs_cfg, prev_val);
        qib_write_kreg(dd, kr_control, dd->control);
}

static int qib_6120_get_ib_cfg(struct qib_pportdata *ppd, int which)
{
        int ret;

        switch (which) {
        case QIB_IB_CFG_LWID:
                ret = ppd->link_width_active;
                break;

        case QIB_IB_CFG_SPD:
                ret = ppd->link_speed_active;
                break;

        case QIB_IB_CFG_LWID_ENB:
                ret = ppd->link_width_enabled;
                break;

        case QIB_IB_CFG_SPD_ENB:
                ret = ppd->link_speed_enabled;
                break;

        case QIB_IB_CFG_OP_VLS:
                ret = ppd->vls_operational;
                break;

        case QIB_IB_CFG_VL_HIGH_CAP:
                ret = 0;
                break;

        case QIB_IB_CFG_VL_LOW_CAP:
                ret = 0;
                break;

        case QIB_IB_CFG_OVERRUN_THRESH: /* IB overrun threshold */
                ret = SYM_FIELD(ppd->dd->cspec->ibcctrl, IBCCtrl,
                                OverrunThreshold);
                break;

        case QIB_IB_CFG_PHYERR_THRESH: /* IB PHY error threshold */
                ret = SYM_FIELD(ppd->dd->cspec->ibcctrl, IBCCtrl,
                                PhyerrThreshold);
                break;

        case QIB_IB_CFG_LINKDEFAULT: /* IB link default (sleep/poll) */
                /* will only take effect when the link state changes */
                ret = (ppd->dd->cspec->ibcctrl &
                       SYM_MASK(IBCCtrl, LinkDownDefaultState)) ?
                        IB_LINKINITCMD_SLEEP : IB_LINKINITCMD_POLL;
                break;

        case QIB_IB_CFG_HRTBT: /* Get Heartbeat off/enable/auto */
                ret = 0; /* no heartbeat on this chip */
                break;

        case QIB_IB_CFG_PMA_TICKS:
                ret = 250; /* 1 usec. */
                break;

        default:
                ret =  -EINVAL;
                break;
        }
        return ret;
}

/*
 * We assume range checking is already done, if needed.
 */
static int qib_6120_set_ib_cfg(struct qib_pportdata *ppd, int which, u32 val)
{
        struct qib_devdata *dd = ppd->dd;
        int ret = 0;
        u64 val64;
        u16 lcmd, licmd;

        switch (which) {
        case QIB_IB_CFG_LWID_ENB:
                ppd->link_width_enabled = val;
                break;

        case QIB_IB_CFG_SPD_ENB:
                ppd->link_speed_enabled = val;
                break;

        case QIB_IB_CFG_OVERRUN_THRESH: /* IB overrun threshold */
                val64 = SYM_FIELD(dd->cspec->ibcctrl, IBCCtrl,
                                  OverrunThreshold);
                if (val64 != val) {
                        dd->cspec->ibcctrl &=
                                ~SYM_MASK(IBCCtrl, OverrunThreshold);
                        dd->cspec->ibcctrl |= (u64) val <<
                                SYM_LSB(IBCCtrl, OverrunThreshold);
                        qib_write_kreg(dd, kr_ibcctrl, dd->cspec->ibcctrl);
                        qib_write_kreg(dd, kr_scratch, 0);
                }
                break;

        case QIB_IB_CFG_PHYERR_THRESH: /* IB PHY error threshold */
                val64 = SYM_FIELD(dd->cspec->ibcctrl, IBCCtrl,
                                  PhyerrThreshold);
                if (val64 != val) {
                        dd->cspec->ibcctrl &=
                                ~SYM_MASK(IBCCtrl, PhyerrThreshold);
                        dd->cspec->ibcctrl |= (u64) val <<
                                SYM_LSB(IBCCtrl, PhyerrThreshold);
                        qib_write_kreg(dd, kr_ibcctrl, dd->cspec->ibcctrl);
                        qib_write_kreg(dd, kr_scratch, 0);
                }
                break;

        case QIB_IB_CFG_PKEYS: /* update pkeys */
                val64 = (u64) ppd->pkeys[0] | ((u64) ppd->pkeys[1] << 16) |
                        ((u64) ppd->pkeys[2] << 32) |
                        ((u64) ppd->pkeys[3] << 48);
                qib_write_kreg(dd, kr_partitionkey, val64);
                break;

        case QIB_IB_CFG_LINKDEFAULT: /* IB link default (sleep/poll) */
                /* will only take effect when the link state changes */
                if (val == IB_LINKINITCMD_POLL)
                        dd->cspec->ibcctrl &=
                                ~SYM_MASK(IBCCtrl, LinkDownDefaultState);
                else /* SLEEP */
                        dd->cspec->ibcctrl |=
                                SYM_MASK(IBCCtrl, LinkDownDefaultState);
                qib_write_kreg(dd, kr_ibcctrl, dd->cspec->ibcctrl);
                qib_write_kreg(dd, kr_scratch, 0);
                break;

        case QIB_IB_CFG_MTU: /* update the MTU in IBC */
                /*
                 * Update our housekeeping variables, and set IBC max
                 * size, same as init code; max IBC is max we allow in
                 * buffer, less the qword pbc, plus 1 for ICRC, in dwords
                 * Set even if it's unchanged, print debug message only
                 * on changes.
                 */
                val = (ppd->ibmaxlen >> 2) + 1;
                dd->cspec->ibcctrl &= ~SYM_MASK(IBCCtrl, MaxPktLen);
                dd->cspec->ibcctrl |= (u64)val <<
                        SYM_LSB(IBCCtrl, MaxPktLen);
                qib_write_kreg(dd, kr_ibcctrl, dd->cspec->ibcctrl);
                qib_write_kreg(dd, kr_scratch, 0);
                break;

        case QIB_IB_CFG_LSTATE: /* set the IB link state */
                switch (val & 0xffff0000) {
                case IB_LINKCMD_DOWN:
                        lcmd = QLOGIC_IB_IBCC_LINKCMD_DOWN;
                        if (!dd->cspec->ibdeltainprog) {
                                dd->cspec->ibdeltainprog = 1;
                                dd->cspec->ibsymsnap =
                                        read_6120_creg32(dd, cr_ibsymbolerr);
                                dd->cspec->iblnkerrsnap =
                                        read_6120_creg32(dd, cr_iblinkerrrecov);
                        }
                        break;

                case IB_LINKCMD_ARMED:
                        lcmd = QLOGIC_IB_IBCC_LINKCMD_ARMED;
                        break;

                case IB_LINKCMD_ACTIVE:
                        lcmd = QLOGIC_IB_IBCC_LINKCMD_ACTIVE;
                        break;

                default:
                        ret = -EINVAL;
                        qib_dev_err(dd, "bad linkcmd req 0x%x\n", val >> 16);
                        goto bail;
                }
                switch (val & 0xffff) {
                case IB_LINKINITCMD_NOP:
                        licmd = 0;
                        break;

                case IB_LINKINITCMD_POLL:
                        licmd = QLOGIC_IB_IBCC_LINKINITCMD_POLL;
                        break;

                case IB_LINKINITCMD_SLEEP:
                        licmd = QLOGIC_IB_IBCC_LINKINITCMD_SLEEP;
                        break;

                case IB_LINKINITCMD_DISABLE:
                        licmd = QLOGIC_IB_IBCC_LINKINITCMD_DISABLE;
                        break;

                default:
                        ret = -EINVAL;
                        qib_dev_err(dd, "bad linkinitcmd req 0x%x\n",
                                    val & 0xffff);
                        goto bail;
                }
                qib_set_ib_6120_lstate(ppd, lcmd, licmd);
                goto bail;

        case QIB_IB_CFG_HRTBT:
                ret = -EINVAL;
                break;

        default:
                ret = -EINVAL;
        }
bail:
        return ret;
}

static int qib_6120_set_loopback(struct qib_pportdata *ppd, const char *what)
{
        int ret = 0;

        if (!strncmp(what, "ibc", 3)) {
                ppd->dd->cspec->ibcctrl |= SYM_MASK(IBCCtrl, Loopback);
                qib_devinfo(ppd->dd->pcidev, "Enabling IB%u:%u IBC loopback\n",
                         ppd->dd->unit, ppd->port);
        } else if (!strncmp(what, "off", 3)) {
                ppd->dd->cspec->ibcctrl &= ~SYM_MASK(IBCCtrl, Loopback);
                qib_devinfo(ppd->dd->pcidev,
                        "Disabling IB%u:%u IBC loopback (normal)\n",
                        ppd->dd->unit, ppd->port);
        } else
                ret = -EINVAL;
        if (!ret) {
                qib_write_kreg(ppd->dd, kr_ibcctrl, ppd->dd->cspec->ibcctrl);
                qib_write_kreg(ppd->dd, kr_scratch, 0);
        }
        return ret;
}

static void pma_6120_timer(unsigned long data)
{
        struct qib_pportdata *ppd = (struct qib_pportdata *)data;
        struct qib_chip_specific *cs = ppd->dd->cspec;
        struct qib_ibport *ibp = &ppd->ibport_data;
        unsigned long flags;

        spin_lock_irqsave(&ibp->rvp.lock, flags);
        if (cs->pma_sample_status == IB_PMA_SAMPLE_STATUS_STARTED) {
                cs->pma_sample_status = IB_PMA_SAMPLE_STATUS_RUNNING;
                qib_snapshot_counters(ppd, &cs->sword, &cs->rword,
                                      &cs->spkts, &cs->rpkts, &cs->xmit_wait);
                mod_timer(&cs->pma_timer,
                      jiffies + usecs_to_jiffies(ibp->rvp.pma_sample_interval));
        } else if (cs->pma_sample_status == IB_PMA_SAMPLE_STATUS_RUNNING) {
                u64 ta, tb, tc, td, te;

                cs->pma_sample_status = IB_PMA_SAMPLE_STATUS_DONE;
                qib_snapshot_counters(ppd, &ta, &tb, &tc, &td, &te);

                cs->sword = ta - cs->sword;
                cs->rword = tb - cs->rword;
                cs->spkts = tc - cs->spkts;
                cs->rpkts = td - cs->rpkts;
                cs->xmit_wait = te - cs->xmit_wait;
        }
        spin_unlock_irqrestore(&ibp->rvp.lock, flags);
}

/*
 * Note that the caller has the ibp->rvp.lock held.
 */
static void qib_set_cntr_6120_sample(struct qib_pportdata *ppd, u32 intv,
                                     u32 start)
{
        struct qib_chip_specific *cs = ppd->dd->cspec;

        if (start && intv) {
                cs->pma_sample_status = IB_PMA_SAMPLE_STATUS_STARTED;
                mod_timer(&cs->pma_timer, jiffies + usecs_to_jiffies(start));
        } else if (intv) {
                cs->pma_sample_status = IB_PMA_SAMPLE_STATUS_RUNNING;
                qib_snapshot_counters(ppd, &cs->sword, &cs->rword,
                                      &cs->spkts, &cs->rpkts, &cs->xmit_wait);
                mod_timer(&cs->pma_timer, jiffies + usecs_to_jiffies(intv));
        } else {
                cs->pma_sample_status = IB_PMA_SAMPLE_STATUS_DONE;
                cs->sword = 0;
                cs->rword = 0;
                cs->spkts = 0;
                cs->rpkts = 0;
                cs->xmit_wait = 0;
        }
}

static u32 qib_6120_iblink_state(u64 ibcs)
{
        u32 state = (u32)SYM_FIELD(ibcs, IBCStatus, LinkState);

        switch (state) {
        case IB_6120_L_STATE_INIT:
                state = IB_PORT_INIT;
                break;
        case IB_6120_L_STATE_ARM:
                state = IB_PORT_ARMED;
                break;
        case IB_6120_L_STATE_ACTIVE:
                /* fall through */
        case IB_6120_L_STATE_ACT_DEFER:
                state = IB_PORT_ACTIVE;
                break;
        default: /* fall through */
        case IB_6120_L_STATE_DOWN:
                state = IB_PORT_DOWN;
                break;
        }
        return state;
}

/* returns the IBTA port state, rather than the IBC link training state */
static u8 qib_6120_phys_portstate(u64 ibcs)
{
        u8 state = (u8)SYM_FIELD(ibcs, IBCStatus, LinkTrainingState);
        return qib_6120_physportstate[state];
}

static int qib_6120_ib_updown(struct qib_pportdata *ppd, int ibup, u64 ibcs)
{
        unsigned long flags;

        spin_lock_irqsave(&ppd->lflags_lock, flags);
        ppd->lflags &= ~QIBL_IB_FORCE_NOTIFY;
        spin_unlock_irqrestore(&ppd->lflags_lock, flags);

        if (ibup) {
                if (ppd->dd->cspec->ibdeltainprog) {
                        ppd->dd->cspec->ibdeltainprog = 0;
                        ppd->dd->cspec->ibsymdelta +=
                                read_6120_creg32(ppd->dd, cr_ibsymbolerr) -
                                        ppd->dd->cspec->ibsymsnap;
                        ppd->dd->cspec->iblnkerrdelta +=
                                read_6120_creg32(ppd->dd, cr_iblinkerrrecov) -
                                        ppd->dd->cspec->iblnkerrsnap;
                }
                qib_hol_init(ppd);
        } else {
                ppd->dd->cspec->lli_counter = 0;
                if (!ppd->dd->cspec->ibdeltainprog) {
                        ppd->dd->cspec->ibdeltainprog = 1;
                        ppd->dd->cspec->ibsymsnap =
                                read_6120_creg32(ppd->dd, cr_ibsymbolerr);
                        ppd->dd->cspec->iblnkerrsnap =
                                read_6120_creg32(ppd->dd, cr_iblinkerrrecov);
                }
                qib_hol_down(ppd);
        }

        qib_6120_setup_setextled(ppd, ibup);

        return 0;
}

/* Does read/modify/write to appropriate registers to
 * set output and direction bits selected by mask.
 * these are in their canonical postions (e.g. lsb of
 * dir will end up in D48 of extctrl on existing chips).
 * returns contents of GP Inputs.
 */
static int gpio_6120_mod(struct qib_devdata *dd, u32 out, u32 dir, u32 mask)
{
        u64 read_val, new_out;
        unsigned long flags;

        if (mask) {
                /* some bits being written, lock access to GPIO */
                dir &= mask;
                out &= mask;
                spin_lock_irqsave(&dd->cspec->gpio_lock, flags);
                dd->cspec->extctrl &= ~((u64)mask << SYM_LSB(EXTCtrl, GPIOOe));
                dd->cspec->extctrl |= ((u64) dir << SYM_LSB(EXTCtrl, GPIOOe));
                new_out = (dd->cspec->gpio_out & ~mask) | out;

                qib_write_kreg(dd, kr_extctrl, dd->cspec->extctrl);
                qib_write_kreg(dd, kr_gpio_out, new_out);
                dd->cspec->gpio_out = new_out;
                spin_unlock_irqrestore(&dd->cspec->gpio_lock, flags);
        }
        /*
         * It is unlikely that a read at this time would get valid
         * data on a pin whose direction line was set in the same
         * call to this function. We include the read here because
         * that allows us to potentially combine a change on one pin with
         * a read on another, and because the old code did something like
         * this.
         */
        read_val = qib_read_kreg64(dd, kr_extstatus);
        return SYM_FIELD(read_val, EXTStatus, GPIOIn);
}

/*
 * Read fundamental info we need to use the chip.  These are
 * the registers that describe chip capabilities, and are
 * saved in shadow registers.
 */
static void get_6120_chip_params(struct qib_devdata *dd)
{
        u64 val;
        u32 piobufs;
        int mtu;

        dd->uregbase = qib_read_kreg32(dd, kr_userregbase);

        dd->rcvtidcnt = qib_read_kreg32(dd, kr_rcvtidcnt);
        dd->rcvtidbase = qib_read_kreg32(dd, kr_rcvtidbase);
        dd->rcvegrbase = qib_read_kreg32(dd, kr_rcvegrbase);
        dd->palign = qib_read_kreg32(dd, kr_palign);
        dd->piobufbase = qib_read_kreg64(dd, kr_sendpiobufbase);
        dd->pio2k_bufbase = dd->piobufbase & 0xffffffff;

        dd->rcvhdrcnt = qib_read_kreg32(dd, kr_rcvegrcnt);

        val = qib_read_kreg64(dd, kr_sendpiosize);
        dd->piosize2k = val & ~0U;
        dd->piosize4k = val >> 32;

        mtu = ib_mtu_enum_to_int(qib_ibmtu);
        if (mtu == -1)
                mtu = QIB_DEFAULT_MTU;
        dd->pport->ibmtu = (u32)mtu;

        val = qib_read_kreg64(dd, kr_sendpiobufcnt);
        dd->piobcnt2k = val & ~0U;
        dd->piobcnt4k = val >> 32;
        dd->last_pio = dd->piobcnt4k + dd->piobcnt2k - 1;
        /* these may be adjusted in init_chip_wc_pat() */
        dd->pio2kbase = (u32 __iomem *)
                (((char __iomem *)dd->kregbase) + dd->pio2k_bufbase);
        if (dd->piobcnt4k) {
                dd->pio4kbase = (u32 __iomem *)
                        (((char __iomem *) dd->kregbase) +
                         (dd->piobufbase >> 32));
                /*
                 * 4K buffers take 2 pages; we use roundup just to be
                 * paranoid; we calculate it once here, rather than on
                 * ever buf allocate
                 */
                dd->align4k = ALIGN(dd->piosize4k, dd->palign);
        }

        piobufs = dd->piobcnt4k + dd->piobcnt2k;

        dd->pioavregs = ALIGN(piobufs, sizeof(u64) * BITS_PER_BYTE / 2) /
                (sizeof(u64) * BITS_PER_BYTE / 2);
}

/*
 * The chip base addresses in cspec and cpspec have to be set
 * after possible init_chip_wc_pat(), rather than in
 * get_6120_chip_params(), so split out as separate function
 */
static void set_6120_baseaddrs(struct qib_devdata *dd)
{
        u32 cregbase;

        cregbase = qib_read_kreg32(dd, kr_counterregbase);
        dd->cspec->cregbase = (u64 __iomem *)
                ((char __iomem *) dd->kregbase + cregbase);

        dd->egrtidbase = (u64 __iomem *)
                ((char __iomem *) dd->kregbase + dd->rcvegrbase);
}

/*
 * Write the final few registers that depend on some of the
 * init setup.  Done late in init, just before bringing up
 * the serdes.
 */
static int qib_late_6120_initreg(struct qib_devdata *dd)
{
        int ret = 0;
        u64 val;

        qib_write_kreg(dd, kr_rcvhdrentsize, dd->rcvhdrentsize);
        qib_write_kreg(dd, kr_rcvhdrsize, dd->rcvhdrsize);
        qib_write_kreg(dd, kr_rcvhdrcnt, dd->rcvhdrcnt);
        qib_write_kreg(dd, kr_sendpioavailaddr, dd->pioavailregs_phys);
        val = qib_read_kreg64(dd, kr_sendpioavailaddr);
        if (val != dd->pioavailregs_phys) {
                qib_dev_err(dd,
                        "Catastrophic software error, SendPIOAvailAddr written as %lx, read back as %llx\n",
                        (unsigned long) dd->pioavailregs_phys,
                        (unsigned long long) val);
                ret = -EINVAL;
        }
        return ret;
}

static int init_6120_variables(struct qib_devdata *dd)
{
        int ret = 0;
        struct qib_pportdata *ppd;
        u32 sbufs;

        ppd = (struct qib_pportdata *)(dd + 1);
        dd->pport = ppd;
        dd->num_pports = 1;

        dd->cspec = (struct qib_chip_specific *)(ppd + dd->num_pports);
        ppd->cpspec = NULL; /* not used in this chip */

        spin_lock_init(&dd->cspec->kernel_tid_lock);
        spin_lock_init(&dd->cspec->user_tid_lock);
        spin_lock_init(&dd->cspec->rcvmod_lock);
        spin_lock_init(&dd->cspec->gpio_lock);

        /* we haven't yet set QIB_PRESENT, so use read directly */
        dd->revision = readq(&dd->kregbase[kr_revision]);

        if ((dd->revision & 0xffffffffU) == 0xffffffffU) {
                qib_dev_err(dd,
                        "Revision register read failure, giving up initialization\n");
                ret = -ENODEV;
                goto bail;
        }
        dd->flags |= QIB_PRESENT;  /* now register routines work */

        dd->majrev = (u8) SYM_FIELD(dd->revision, Revision_R,
                                    ChipRevMajor);
        dd->minrev = (u8) SYM_FIELD(dd->revision, Revision_R,
                                    ChipRevMinor);

        get_6120_chip_params(dd);
        pe_boardname(dd); /* fill in boardname */

        /*
         * GPIO bits for TWSI data and clock,
         * used for serial EEPROM.
         */
        dd->gpio_sda_num = _QIB_GPIO_SDA_NUM;
        dd->gpio_scl_num = _QIB_GPIO_SCL_NUM;
        dd->twsi_eeprom_dev = QIB_TWSI_NO_DEV;

        if (qib_unordered_wc())
                dd->flags |= QIB_PIO_FLUSH_WC;

        /*
         * EEPROM error log 0 is TXE Parity errors. 1 is RXE Parity.
         * 2 is Some Misc, 3 is reserved for future.
         */
        dd->eep_st_masks[0].hwerrs_to_log = HWE_MASK(TXEMemParityErr);

        /* Ignore errors in PIO/PBC on systems with unordered write-combining */
        if (qib_unordered_wc())
                dd->eep_st_masks[0].hwerrs_to_log &= ~TXE_PIO_PARITY;

        dd->eep_st_masks[1].hwerrs_to_log = HWE_MASK(RXEMemParityErr);

        dd->eep_st_masks[2].errs_to_log = ERR_MASK(ResetNegated);

        ret = qib_init_pportdata(ppd, dd, 0, 1);
        if (ret)
                goto bail;
        ppd->link_width_supported = IB_WIDTH_1X | IB_WIDTH_4X;
        ppd->link_speed_supported = QIB_IB_SDR;
        ppd->link_width_enabled = IB_WIDTH_4X;
        ppd->link_speed_enabled = ppd->link_speed_supported;
        /* these can't change for this chip, so set once */
        ppd->link_width_active = ppd->link_width_enabled;
        ppd->link_speed_active = ppd->link_speed_enabled;
        ppd->vls_supported = IB_VL_VL0;
        ppd->vls_operational = ppd->vls_supported;

        dd->rcvhdrentsize = QIB_RCVHDR_ENTSIZE;
        dd->rcvhdrsize = QIB_DFLT_RCVHDRSIZE;
        dd->rhf_offset = 0;

        /* we always allocate at least 2048 bytes for eager buffers */
        ret = ib_mtu_enum_to_int(qib_ibmtu);
        dd->rcvegrbufsize = ret != -1 ? max(ret, 2048) : QIB_DEFAULT_MTU;
        BUG_ON(!is_power_of_2(dd->rcvegrbufsize));
        dd->rcvegrbufsize_shift = ilog2(dd->rcvegrbufsize);

        qib_6120_tidtemplate(dd);

        /*
         * We can request a receive interrupt for 1 or
         * more packets from current offset.  For now, we set this
         * up for a single packet.
         */
        dd->rhdrhead_intr_off = 1ULL << 32;

        /* setup the stats timer; the add_timer is done at end of init */
        init_timer(&dd->stats_timer);
        dd->stats_timer.function = qib_get_6120_faststats;
        dd->stats_timer.data = (unsigned long) dd;

        init_timer(&dd->cspec->pma_timer);
        dd->cspec->pma_timer.function = pma_6120_timer;
        dd->cspec->pma_timer.data = (unsigned long) ppd;

        dd->ureg_align = qib_read_kreg32(dd, kr_palign);

        dd->piosize2kmax_dwords = dd->piosize2k >> 2;
        qib_6120_config_ctxts(dd);
        qib_set_ctxtcnt(dd);

        ret = init_chip_wc_pat(dd, 0);
        if (ret)
                goto bail;
        set_6120_baseaddrs(dd); /* set chip access pointers now */

        ret = 0;
        if (qib_mini_init)
                goto bail;

        qib_num_cfg_vls = 1; /* if any 6120's, only one VL */

        ret = qib_create_ctxts(dd);
        init_6120_cntrnames(dd);

        /* use all of 4KB buffers for the kernel, otherwise 16 */
        sbufs = dd->piobcnt4k ?  dd->piobcnt4k : 16;

        dd->lastctxt_piobuf = dd->piobcnt2k + dd->piobcnt4k - sbufs;
        dd->pbufsctxt = dd->lastctxt_piobuf /
                (dd->cfgctxts - dd->first_user_ctxt);

        if (ret)
                goto bail;
bail:
        return ret;
}

/*
 * For this chip, we want to use the same buffer every time
 * when we are trying to bring the link up (they are always VL15
 * packets).  At that link state the packet should always go out immediately
 * (or at least be discarded at the tx interface if the link is down).
 * If it doesn't, and the buffer isn't available, that means some other
 * sender has gotten ahead of us, and is preventing our packet from going
 * out.  In that case, we flush all packets, and try again.  If that still
 * fails, we fail the request, and hope things work the next time around.
 *
 * We don't need very complicated heuristics on whether the packet had
 * time to go out or not, since even at SDR 1X, it goes out in very short
 * time periods, covered by the chip reads done here and as part of the
 * flush.
 */
static u32 __iomem *get_6120_link_buf(struct qib_pportdata *ppd, u32 *bnum)
{
        u32 __iomem *buf;
        u32 lbuf = ppd->dd->piobcnt2k + ppd->dd->piobcnt4k - 1;

        /*
         * always blip to get avail list updated, since it's almost
         * always needed, and is fairly cheap.
         */
        sendctrl_6120_mod(ppd->dd->pport, QIB_SENDCTRL_AVAIL_BLIP);
        qib_read_kreg64(ppd->dd, kr_scratch); /* extra chip flush */
        buf = qib_getsendbuf_range(ppd->dd, bnum, lbuf, lbuf);
        if (buf)
                goto done;

        sendctrl_6120_mod(ppd, QIB_SENDCTRL_DISARM_ALL | QIB_SENDCTRL_FLUSH |
                          QIB_SENDCTRL_AVAIL_BLIP);
        ppd->dd->upd_pio_shadow  = 1; /* update our idea of what's busy */
        qib_read_kreg64(ppd->dd, kr_scratch); /* extra chip flush */
        buf = qib_getsendbuf_range(ppd->dd, bnum, lbuf, lbuf);
done:
        return buf;
}

static u32 __iomem *qib_6120_getsendbuf(struct qib_pportdata *ppd, u64 pbc,
                                        u32 *pbufnum)
{
        u32 first, last, plen = pbc & QIB_PBC_LENGTH_MASK;
        struct qib_devdata *dd = ppd->dd;
        u32 __iomem *buf;

        if (((pbc >> 32) & PBC_6120_VL15_SEND_CTRL) &&
                !(ppd->lflags & (QIBL_IB_AUTONEG_INPROG | QIBL_LINKACTIVE)))
                buf = get_6120_link_buf(ppd, pbufnum);
        else {

                if ((plen + 1) > dd->piosize2kmax_dwords)
                        first = dd->piobcnt2k;
                else
                        first = 0;
                /* try 4k if all 2k busy, so same last for both sizes */
                last = dd->piobcnt2k + dd->piobcnt4k - 1;
                buf = qib_getsendbuf_range(dd, pbufnum, first, last);
        }
        return buf;
}

static int init_sdma_6120_regs(struct qib_pportdata *ppd)
{
        return -ENODEV;
}

static u16 qib_sdma_6120_gethead(struct qib_pportdata *ppd)
{
        return 0;
}

static int qib_sdma_6120_busy(struct qib_pportdata *ppd)
{
        return 0;
}

static void qib_sdma_update_6120_tail(struct qib_pportdata *ppd, u16 tail)
{
}

static void qib_6120_sdma_sendctrl(struct qib_pportdata *ppd, unsigned op)
{
}

static void qib_sdma_set_6120_desc_cnt(struct qib_pportdata *ppd, unsigned cnt)
{
}

/*
 * the pbc doesn't need a VL15 indicator, but we need it for link_buf.
 * The chip ignores the bit if set.
 */
static u32 qib_6120_setpbc_control(struct qib_pportdata *ppd, u32 plen,
                                   u8 srate, u8 vl)
{
        return vl == 15 ? PBC_6120_VL15_SEND_CTRL : 0;
}

static void qib_6120_initvl15_bufs(struct qib_devdata *dd)
{
}

static void qib_6120_init_ctxt(struct qib_ctxtdata *rcd)
{
        rcd->rcvegrcnt = rcd->dd->rcvhdrcnt;
        rcd->rcvegr_tid_base = rcd->ctxt * rcd->rcvegrcnt;
}

static void qib_6120_txchk_change(struct qib_devdata *dd, u32 start,
        u32 len, u32 avail, struct qib_ctxtdata *rcd)
{
}

static void writescratch(struct qib_devdata *dd, u32 val)
{
        (void) qib_write_kreg(dd, kr_scratch, val);
}

static int qib_6120_tempsense_rd(struct qib_devdata *dd, int regnum)
{
        return -ENXIO;
}

#ifdef CONFIG_INFINIBAND_QIB_DCA
static int qib_6120_notify_dca(struct qib_devdata *dd, unsigned long event)
{
        return 0;
}
#endif

/* Dummy function, as 6120 boards never disable EEPROM Write */
static int qib_6120_eeprom_wen(struct qib_devdata *dd, int wen)
{
        return 1;
}

/**
 * qib_init_iba6120_funcs - set up the chip-specific function pointers
 * @pdev: pci_dev of the qlogic_ib device
 * @ent: pci_device_id matching this chip
 *
 * This is global, and is called directly at init to set up the
 * chip-specific function pointers for later use.
 *
 * It also allocates/partially-inits the qib_devdata struct for
 * this device.
 */
struct qib_devdata *qib_init_iba6120_funcs(struct pci_dev *pdev,
                                           const struct pci_device_id *ent)
{
        struct qib_devdata *dd;
        int ret;

        dd = qib_alloc_devdata(pdev, sizeof(struct qib_pportdata) +
                               sizeof(struct qib_chip_specific));
        if (IS_ERR(dd))
                goto bail;

        dd->f_bringup_serdes    = qib_6120_bringup_serdes;
        dd->f_cleanup           = qib_6120_setup_cleanup;
        dd->f_clear_tids        = qib_6120_clear_tids;
        dd->f_free_irq          = qib_6120_free_irq;
        dd->f_get_base_info     = qib_6120_get_base_info;
        dd->f_get_msgheader     = qib_6120_get_msgheader;
        dd->f_getsendbuf        = qib_6120_getsendbuf;
        dd->f_gpio_mod          = gpio_6120_mod;
        dd->f_eeprom_wen        = qib_6120_eeprom_wen;
        dd->f_hdrqempty         = qib_6120_hdrqempty;
        dd->f_ib_updown         = qib_6120_ib_updown;
        dd->f_init_ctxt         = qib_6120_init_ctxt;
        dd->f_initvl15_bufs     = qib_6120_initvl15_bufs;
        dd->f_intr_fallback     = qib_6120_nointr_fallback;
        dd->f_late_initreg      = qib_late_6120_initreg;
        dd->f_setpbc_control    = qib_6120_setpbc_control;
        dd->f_portcntr          = qib_portcntr_6120;
        dd->f_put_tid           = (dd->minrev >= 2) ?
                                      qib_6120_put_tid_2 :
                                      qib_6120_put_tid;
        dd->f_quiet_serdes      = qib_6120_quiet_serdes;
        dd->f_rcvctrl           = rcvctrl_6120_mod;
        dd->f_read_cntrs        = qib_read_6120cntrs;
        dd->f_read_portcntrs    = qib_read_6120portcntrs;
        dd->f_reset             = qib_6120_setup_reset;
        dd->f_init_sdma_regs    = init_sdma_6120_regs;
        dd->f_sdma_busy         = qib_sdma_6120_busy;
        dd->f_sdma_gethead      = qib_sdma_6120_gethead;
        dd->f_sdma_sendctrl     = qib_6120_sdma_sendctrl;
        dd->f_sdma_set_desc_cnt = qib_sdma_set_6120_desc_cnt;
        dd->f_sdma_update_tail  = qib_sdma_update_6120_tail;
        dd->f_sendctrl          = sendctrl_6120_mod;
        dd->f_set_armlaunch     = qib_set_6120_armlaunch;
        dd->f_set_cntr_sample   = qib_set_cntr_6120_sample;
        dd->f_iblink_state      = qib_6120_iblink_state;
        dd->f_ibphys_portstate  = qib_6120_phys_portstate;
        dd->f_get_ib_cfg        = qib_6120_get_ib_cfg;
        dd->f_set_ib_cfg        = qib_6120_set_ib_cfg;
        dd->f_set_ib_loopback   = qib_6120_set_loopback;
        dd->f_set_intr_state    = qib_6120_set_intr_state;
        dd->f_setextled         = qib_6120_setup_setextled;
        dd->f_txchk_change      = qib_6120_txchk_change;
        dd->f_update_usrhead    = qib_update_6120_usrhead;
        dd->f_wantpiobuf_intr   = qib_wantpiobuf_6120_intr;
        dd->f_xgxs_reset        = qib_6120_xgxs_reset;
        dd->f_writescratch      = writescratch;
        dd->f_tempsense_rd      = qib_6120_tempsense_rd;
#ifdef CONFIG_INFINIBAND_QIB_DCA
        dd->f_notify_dca = qib_6120_notify_dca;
#endif
        /*
         * Do remaining pcie setup and save pcie values in dd.
         * Any error printing is already done by the init code.
         * On return, we have the chip mapped and accessible,
         * but chip registers are not set up until start of
         * init_6120_variables.
         */
        ret = qib_pcie_ddinit(dd, pdev, ent);
        if (ret < 0)
                goto bail_free;

        /* initialize chip-specific variables */
        ret = init_6120_variables(dd);
        if (ret)
                goto bail_cleanup;

        if (qib_mini_init)
                goto bail;

        if (qib_pcie_params(dd, 8, NULL, NULL))
                qib_dev_err(dd,
                        "Failed to setup PCIe or interrupts; continuing anyway\n");
        dd->cspec->irq = pdev->irq; /* save IRQ */

        /* clear diagctrl register, in case diags were running and crashed */
        qib_write_kreg(dd, kr_hwdiagctrl, 0);

        if (qib_read_kreg64(dd, kr_hwerrstatus) &
            QLOGIC_IB_HWE_SERDESPLLFAILED)
                qib_write_kreg(dd, kr_hwerrclear,
                               QLOGIC_IB_HWE_SERDESPLLFAILED);

        /* setup interrupt handler (interrupt type handled above) */
        qib_setup_6120_interrupt(dd);
        /* Note that qpn_mask is set by qib_6120_config_ctxts() first */
        qib_6120_init_hwerrors(dd);

        goto bail;

bail_cleanup:
        qib_pcie_ddcleanup(dd);
bail_free:
        qib_free_devdata(dd);
        dd = ERR_PTR(ret);
bail:
        return dd;
}