drivers/media/rc/Kconfig

   1 config RC_CORE
   2         tristate
   3         depends on MEDIA_RC_SUPPORT
   4         depends on INPUT
   5         default y
   6
   7 source "drivers/media/rc/keymaps/Kconfig"
   8
   9 menuconfig RC_DECODERS
  10         bool "Remote controller decoders"
  11         depends on RC_CORE
  12         default y
  13
  14 if RC_DECODERS
  15 config LIRC
  16         tristate "LIRC interface driver"
  17         depends on RC_CORE
  18
  19         ---help---
  20            Enable this option to build the Linux Infrared Remote
  21            Control (LIRC) core device interface driver. The LIRC
  22            interface passes raw IR to and from userspace, where the
  23            LIRC daemon handles protocol decoding for IR reception and
  24            encoding for IR transmitting (aka "blasting").
  25
  26 config IR_LIRC_CODEC
  27         tristate "Enable IR to LIRC bridge"
  28         depends on RC_CORE
  29         depends on LIRC
  30         default y
  31
  32         ---help---
  33            Enable this option to pass raw IR to and from userspace via
  34            the LIRC interface.
  35
  36
  37 config IR_NEC_DECODER
  38         tristate "Enable IR raw decoder for the NEC protocol"
  39         depends on RC_CORE
  40         select BITREVERSE
  41         default y
  42
  43         ---help---
  44            Enable this option if you have IR with NEC protocol, and
  45            if the IR is decoded in software
  46
  47 config IR_RC5_DECODER
  48         tristate "Enable IR raw decoder for the RC-5 protocol"
  49         depends on RC_CORE
  50         select BITREVERSE
  51         default y
  52
  53         ---help---
  54            Enable this option if you have IR with RC-5 protocol, and
  55            if the IR is decoded in software
  56
  57 config IR_RC6_DECODER
  58         tristate "Enable IR raw decoder for the RC6 protocol"
  59         depends on RC_CORE
  60         select BITREVERSE
  61         default y
  62
  63         ---help---
  64            Enable this option if you have an infrared remote control which
  65            uses the RC6 protocol, and you need software decoding support.
  66
  67 config IR_JVC_DECODER
  68         tristate "Enable IR raw decoder for the JVC protocol"
  69         depends on RC_CORE
  70         select BITREVERSE
  71         default y
  72
  73         ---help---
  74            Enable this option if you have an infrared remote control which
  75            uses the JVC protocol, and you need software decoding support.
  76
  77 config IR_SONY_DECODER
  78         tristate "Enable IR raw decoder for the Sony protocol"
  79         depends on RC_CORE
  80         select BITREVERSE
  81         default y
  82
  83         ---help---
  84            Enable this option if you have an infrared remote control which
  85            uses the Sony protocol, and you need software decoding support.
  86
  87 config IR_SANYO_DECODER
  88         tristate "Enable IR raw decoder for the Sanyo protocol"
  89         depends on RC_CORE
  90         default y
  91
  92         ---help---
  93            Enable this option if you have an infrared remote control which
  94            uses the Sanyo protocol (Sanyo, Aiwa, Chinon remotes),
  95            and you need software decoding support.
  96
  97 config IR_SHARP_DECODER
  98         tristate "Enable IR raw decoder for the Sharp protocol"
  99         depends on RC_CORE
 100         default y
 101
 102         ---help---
 103            Enable this option if you have an infrared remote control which
 104            uses the Sharp protocol, and you need software decoding support.
 105
 106 config IR_MCE_KBD_DECODER
 107         tristate "Enable IR raw decoder for the MCE keyboard/mouse protocol"
 108         depends on RC_CORE
 109         select BITREVERSE
 110         default y
 111
 112         ---help---
 113            Enable this option if you have a Microsoft Remote Keyboard for
 114            Windows Media Center Edition, which you would like to use with
 115            a raw IR receiver in your system.
 116
 117 config IR_XMP_DECODER
 118         tristate "Enable IR raw decoder for the XMP protocol"
 119         depends on RC_CORE
 120         select BITREVERSE
 121         default y
 122
 123         ---help---
 124            Enable this option if you have IR with XMP protocol, and
 125            if the IR is decoded in software
 126 endif #RC_DECODERS
 127
 128 menuconfig RC_DEVICES
 129         bool "Remote Controller devices"
 130         depends on RC_CORE
 131
 132 if RC_DEVICES
 133
 134 config RC_ATI_REMOTE
 135         tristate "ATI / X10 based USB RF remote controls"
 136         depends on USB_ARCH_HAS_HCD
 137         depends on RC_CORE
 138         select USB
 139         help
 140            Say Y here if you want to use an X10 based USB remote control.
 141            These are RF remotes with USB receivers.
 142
 143            Such devices include the ATI remote that comes with many of ATI's
 144            All-In-Wonder video cards, the X10 "Lola" remote, NVIDIA RF remote,
 145            Medion RF remote, and SnapStream FireFly remote.
 146
 147            This driver provides mouse pointer, left and right mouse buttons,
 148            and maps all the other remote buttons to keypress events.
 149
 150            To compile this driver as a module, choose M here: the module will be
 151            called ati_remote.
 152
 153 config IR_ENE
 154         tristate "ENE eHome Receiver/Transceiver (pnp id: ENE0100/ENE02xxx)"
 155         depends on PNP
 156         depends on RC_CORE
 157         ---help---
 158            Say Y here to enable support for integrated infrared receiver
 159            /transceiver made by ENE.
 160
 161            You can see if you have it by looking at lspnp output.
 162            Output should include ENE0100 ENE0200 or something similar.
 163
 164            To compile this driver as a module, choose M here: the
 165            module will be called ene_ir.
 166
 167 config IR_HIX5HD2
 168         tristate "Hisilicon hix5hd2 IR remote control"
 169         depends on RC_CORE
 170         help
 171          Say Y here if you want to use hisilicon hix5hd2 remote control.
 172          To compile this driver as a module, choose M here: the module will be
 173          called ir-hix5hd2.
 174
 175          If you're not sure, select N here
 176
 177 config IR_IMON
 178         tristate "SoundGraph iMON Receiver and Display"
 179         depends on USB_ARCH_HAS_HCD
 180         depends on RC_CORE
 181         select USB
 182         ---help---
 183            Say Y here if you want to use a SoundGraph iMON (aka Antec Veris)
 184            IR Receiver and/or LCD/VFD/VGA display.
 185
 186            To compile this driver as a module, choose M here: the
 187            module will be called imon.
 188
 189 config IR_MCEUSB
 190         tristate "Windows Media Center Ed. eHome Infrared Transceiver"
 191         depends on USB_ARCH_HAS_HCD
 192         depends on RC_CORE
 193         select USB
 194         ---help---
 195            Say Y here if you want to use a Windows Media Center Edition
 196            eHome Infrared Transceiver.
 197
 198            To compile this driver as a module, choose M here: the
 199            module will be called mceusb.
 200
 201 config IR_ITE_CIR
 202         tristate "ITE Tech Inc. IT8712/IT8512 Consumer Infrared Transceiver"
 203         depends on PNP
 204         depends on RC_CORE
 205         ---help---
 206            Say Y here to enable support for integrated infrared receivers
 207            /transceivers made by ITE Tech Inc. These are found in
 208            several ASUS devices, like the ASUS Digimatrix or the ASUS
 209            EEEBox 1501U.
 210
 211            To compile this driver as a module, choose M here: the
 212            module will be called ite-cir.
 213
 214 config IR_FINTEK
 215         tristate "Fintek Consumer Infrared Transceiver"
 216         depends on PNP
 217         depends on RC_CORE
 218         ---help---
 219            Say Y here to enable support for integrated infrared receiver
 220            /transciever made by Fintek. This chip is found on assorted
 221            Jetway motherboards (and of course, possibly others).
 222
 223            To compile this driver as a module, choose M here: the
 224            module will be called fintek-cir.
 225
 226 config IR_MESON
 227         tristate "Amlogic Meson IR remote receiver"
 228         depends on RC_CORE
 229         depends on ARCH_MESON || COMPILE_TEST
 230         ---help---
 231            Say Y if you want to use the IR remote receiver available
 232            on Amlogic Meson SoCs.
 233
 234            To compile this driver as a module, choose M here: the
 235            module will be called meson-ir.
 236
 237 config IR_NUVOTON
 238         tristate "Nuvoton w836x7hg Consumer Infrared Transceiver"
 239         depends on PNP
 240         depends on RC_CORE
 241         ---help---
 242            Say Y here to enable support for integrated infrared receiver
 243            /transciever made by Nuvoton (formerly Winbond). This chip is
 244            found in the ASRock ION 330HT, as well as assorted Intel
 245            DP55-series motherboards (and of course, possibly others).
 246
 247            To compile this driver as a module, choose M here: the
 248            module will be called nuvoton-cir.
 249
 250 config IR_REDRAT3
 251         tristate "RedRat3 IR Transceiver"
 252         depends on USB_ARCH_HAS_HCD
 253         depends on RC_CORE
 254         select NEW_LEDS
 255         select LEDS_CLASS
 256         select USB
 257         ---help---
 258            Say Y here if you want to use a RedRat3 Infrared Transceiver.
 259
 260            To compile this driver as a module, choose M here: the
 261            module will be called redrat3.
 262
 263 config IR_STREAMZAP
 264         tristate "Streamzap PC Remote IR Receiver"
 265         depends on USB_ARCH_HAS_HCD
 266         depends on RC_CORE
 267         select USB
 268         ---help---
 269            Say Y here if you want to use a Streamzap PC Remote
 270            Infrared Receiver.
 271
 272            To compile this driver as a module, choose M here: the
 273            module will be called streamzap.
 274
 275 config IR_WINBOND_CIR
 276         tristate "Winbond IR remote control"
 277         depends on X86 && PNP
 278         depends on RC_CORE
 279         select NEW_LEDS
 280         select LEDS_CLASS
 281         select BITREVERSE
 282         ---help---
 283            Say Y here if you want to use the IR remote functionality found
 284            in some Winbond SuperI/O chips. Currently only the WPCD376I
 285            chip is supported (included in some Intel Media series
 286            motherboards).
 287
 288            To compile this driver as a module, choose M here: the module will
 289            be called winbond_cir.
 290
 291 config IR_IGORPLUGUSB
 292         tristate "IgorPlug-USB IR Receiver"
 293         depends on USB_ARCH_HAS_HCD
 294         depends on RC_CORE
 295         select USB
 296         ---help---
 297            Say Y here if you want to use the IgorPlug-USB IR Receiver by
 298            Igor Cesko. This device is included on the Fit-PC2.
 299
 300            Note that this device can only record bursts of 36 IR pulses and
 301            spaces, which is not enough for the NEC, Sanyo and RC-6 protocol.
 302
 303            To compile this driver as a module, choose M here: the module will
 304            be called igorplugusb.
 305
 306 config IR_IGUANA
 307         tristate "IguanaWorks USB IR Transceiver"
 308         depends on USB_ARCH_HAS_HCD
 309         depends on RC_CORE
 310         select USB
 311         ---help---
 312            Say Y here if you want to use the IguanaWorks USB IR Transceiver.
 313            Both infrared receive and send are supported. If you want to
 314            change the ID or the pin config, use the user space driver from
 315            IguanaWorks.
 316
 317            Only firmware 0x0205 and later is supported.
 318
 319            To compile this driver as a module, choose M here: the module will
 320            be called iguanair.
 321
 322 config IR_TTUSBIR
 323         tristate "TechnoTrend USB IR Receiver"
 324         depends on USB_ARCH_HAS_HCD
 325         depends on RC_CORE
 326         select USB
 327         select NEW_LEDS
 328         select LEDS_CLASS
 329         ---help---
 330            Say Y here if you want to use the TechnoTrend USB IR Receiver. The
 331            driver can control the led.
 332
 333            To compile this driver as a module, choose M here: the module will
 334            be called ttusbir.
 335
 336 config IR_RX51
 337         tristate "Nokia N900 IR transmitter diode"
 338         depends on OMAP_DM_TIMER && ARCH_OMAP2PLUS && LIRC && !ARCH_MULTIPLATFORM
 339         ---help---
 340            Say Y or M here if you want to enable support for the IR
 341            transmitter diode built in the Nokia N900 (RX51) device.
 342
 343            The driver uses omap DM timers for generating the carrier
 344            wave and pulses.
 345
 346 source "drivers/media/rc/img-ir/Kconfig"
 347
 348 config RC_LOOPBACK
 349         tristate "Remote Control Loopback Driver"
 350         depends on RC_CORE
 351         ---help---
 352            Say Y here if you want support for the remote control loopback
 353            driver which allows TX data to be sent back as RX data.
 354            This is mostly useful for debugging purposes.
 355
 356            If you're not sure, select N here.
 357
 358            To compile this driver as a module, choose M here: the module will
 359            be called rc_loopback.
 360
 361 config IR_GPIO_CIR
 362         tristate "GPIO IR remote control"
 363         depends on RC_CORE
 364         ---help---
 365            Say Y if you want to use GPIO based IR Receiver.
 366
 367            To compile this driver as a module, choose M here: the module will
 368            be called gpio-ir-recv.
 369
 370 config RC_ST
 371         tristate "ST remote control receiver"
 372         depends on RC_CORE
 373         depends on ARCH_STI || COMPILE_TEST
 374         help
 375          Say Y here if you want support for ST remote control driver
 376          which allows both IR and UHF RX.
 377          The driver passes raw pulse and space information to the LIRC decoder.
 378
 379          If you're not sure, select N here.
 380
 381 config IR_SUNXI
 382     tristate "SUNXI IR remote control"
 383     depends on RC_CORE
 384     depends on ARCH_SUNXI || COMPILE_TEST
 385     ---help---
 386       Say Y if you want to use sunXi internal IR Controller
 387
 388       To compile this driver as a module, choose M here: the module will
 389       be called sunxi-ir.
 390
 391 endif #RC_DEVICES