drivers/media/video/em28xx/em28xx-reg.h

   1 #define EM_GPIO_0  (1 << 0)
   2 #define EM_GPIO_1  (1 << 1)
   3 #define EM_GPIO_2  (1 << 2)
   4 #define EM_GPIO_3  (1 << 3)
   5 #define EM_GPIO_4  (1 << 4)
   6 #define EM_GPIO_5  (1 << 5)
   7 #define EM_GPIO_6  (1 << 6)
   8 #define EM_GPIO_7  (1 << 7)
   9
  10 #define EM_GPO_0   (1 << 0)
  11 #define EM_GPO_1   (1 << 1)
  12 #define EM_GPO_2   (1 << 2)
  13 #define EM_GPO_3   (1 << 3)
  14
  15 /* em2800 registers */
  16 #define EM2800_R08_AUDIOSRC 0x08
  17
  18 /* em28xx registers */
  19
  20 #define EM28XX_R00_CHIPCFG      0x00
  21
  22 /* em28xx Chip Configuration 0x00 */
  23 #define EM28XX_CHIPCFG_VENDOR_AUDIO             0x80
  24 #define EM28XX_CHIPCFG_I2S_VOLUME_CAPABLE       0x40
  25 #define EM28XX_CHIPCFG_I2S_5_SAMPRATES          0x30
  26 #define EM28XX_CHIPCFG_I2S_3_SAMPRATES          0x20
  27 #define EM28XX_CHIPCFG_AC97                     0x10
  28 #define EM28XX_CHIPCFG_AUDIOMASK                0x30
  29
  30 #define EM28XX_R01_CHIPCFG2     0x01
  31
  32 /* em28xx Chip Configuration 2 0x01 */
  33 #define EM28XX_CHIPCFG2_TS_PRESENT              0x10
  34 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_MASK    0x0c /* bits 3-2 */
  35 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_1MF     0x00
  36 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_2MF     0x04
  37 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_4MF     0x08
  38 #define EM28XX_CHIPCFG2_TS_REQ_INTERVAL_8MF     0x0c
  39 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_MASK      0x03 /* bits 0-1 */
  40 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_188       0x00
  41 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_376       0x01
  42 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_564       0x02
  43 #define EM28XX_CHIPCFG2_TS_PACKETSIZE_752       0x03
  44
  45
  46         /* GPIO/GPO registers */
  47 #define EM2880_R04_GPO  0x04    /* em2880-em2883 only */
  48 #define EM28XX_R08_GPIO 0x08    /* em2820 or upper */
  49
  50 #define EM28XX_R06_I2C_CLK      0x06
  51
  52 /* em28xx I2C Clock Register (0x06) */
  53 #define EM28XX_I2C_CLK_ACK_LAST_READ    0x80
  54 #define EM28XX_I2C_CLK_WAIT_ENABLE      0x40
  55 #define EM28XX_I2C_EEPROM_ON_BOARD      0x08
  56 #define EM28XX_I2C_EEPROM_KEY_VALID     0x04
  57 #define EM2874_I2C_SECONDARY_BUS_SELECT 0x04 /* em2874 has two i2c busses */
  58 #define EM28XX_I2C_FREQ_1_5_MHZ         0x03 /* bus frequency (bits [1-0]) */
  59 #define EM28XX_I2C_FREQ_25_KHZ          0x02
  60 #define EM28XX_I2C_FREQ_400_KHZ         0x01
  61 #define EM28XX_I2C_FREQ_100_KHZ         0x00
  62
  63
  64 #define EM28XX_R0A_CHIPID       0x0a
  65 #define EM28XX_R0C_USBSUSP      0x0c    /* */
  66
  67 #define EM28XX_R0E_AUDIOSRC     0x0e
  68 #define EM28XX_R0F_XCLK 0x0f
  69
  70 /* em28xx XCLK Register (0x0f) */
  71 #define EM28XX_XCLK_AUDIO_UNMUTE        0x80 /* otherwise audio muted */
  72 #define EM28XX_XCLK_I2S_MSB_TIMING      0x40 /* otherwise standard timing */
  73 #define EM28XX_XCLK_IR_RC5_MODE         0x20 /* otherwise NEC mode */
  74 #define EM28XX_XCLK_IR_NEC_CHK_PARITY   0x10
  75 #define EM28XX_XCLK_FREQUENCY_30MHZ     0x00 /* Freq. select (bits [3-0]) */
  76 #define EM28XX_XCLK_FREQUENCY_15MHZ     0x01
  77 #define EM28XX_XCLK_FREQUENCY_10MHZ     0x02
  78 #define EM28XX_XCLK_FREQUENCY_7_5MHZ    0x03
  79 #define EM28XX_XCLK_FREQUENCY_6MHZ      0x04
  80 #define EM28XX_XCLK_FREQUENCY_5MHZ      0x05
  81 #define EM28XX_XCLK_FREQUENCY_4_3MHZ    0x06
  82 #define EM28XX_XCLK_FREQUENCY_12MHZ     0x07
  83 #define EM28XX_XCLK_FREQUENCY_20MHZ     0x08
  84 #define EM28XX_XCLK_FREQUENCY_20MHZ_2   0x09
  85 #define EM28XX_XCLK_FREQUENCY_48MHZ     0x0a
  86 #define EM28XX_XCLK_FREQUENCY_24MHZ     0x0b
  87
  88 #define EM28XX_R10_VINMODE      0x10
  89 #define EM28XX_R11_VINCTRL      0x11
  90 #define EM28XX_R12_VINENABLE    0x12    /* */
  91
  92 #define EM28XX_R14_GAMMA        0x14
  93 #define EM28XX_R15_RGAIN        0x15
  94 #define EM28XX_R16_GGAIN        0x16
  95 #define EM28XX_R17_BGAIN        0x17
  96 #define EM28XX_R18_ROFFSET      0x18
  97 #define EM28XX_R19_GOFFSET      0x19
  98 #define EM28XX_R1A_BOFFSET      0x1a
  99
 100 #define EM28XX_R1B_OFLOW        0x1b
 101 #define EM28XX_R1C_HSTART       0x1c
 102 #define EM28XX_R1D_VSTART       0x1d
 103 #define EM28XX_R1E_CWIDTH       0x1e
 104 #define EM28XX_R1F_CHEIGHT      0x1f
 105
 106 #define EM28XX_R20_YGAIN        0x20
 107 #define EM28XX_R21_YOFFSET      0x21
 108 #define EM28XX_R22_UVGAIN       0x22
 109 #define EM28XX_R23_UOFFSET      0x23
 110 #define EM28XX_R24_VOFFSET      0x24
 111 #define EM28XX_R25_SHARPNESS    0x25
 112
 113 #define EM28XX_R26_COMPR        0x26
 114 #define EM28XX_R27_OUTFMT       0x27
 115
 116 /* em28xx Output Format Register (0x27) */
 117 #define EM28XX_OUTFMT_RGB_8_RGRG        0x00
 118 #define EM28XX_OUTFMT_RGB_8_GRGR        0x01
 119 #define EM28XX_OUTFMT_RGB_8_GBGB        0x02
 120 #define EM28XX_OUTFMT_RGB_8_BGBG        0x03
 121 #define EM28XX_OUTFMT_RGB_16_656        0x04
 122 #define EM28XX_OUTFMT_RGB_8_BAYER       0x08 /* Pattern in Reg 0x10[1-0] */
 123 #define EM28XX_OUTFMT_YUV211            0x10
 124 #define EM28XX_OUTFMT_YUV422_Y0UY1V     0x14
 125 #define EM28XX_OUTFMT_YUV422_Y1UY0V     0x15
 126 #define EM28XX_OUTFMT_YUV411            0x18
 127
 128
 129 #define EM28XX_R28_XMIN 0x28
 130 #define EM28XX_R29_XMAX 0x29
 131 #define EM28XX_R2A_YMIN 0x2a
 132 #define EM28XX_R2B_YMAX 0x2b
 133
 134 #define EM28XX_R30_HSCALELOW    0x30
 135 #define EM28XX_R31_HSCALEHIGH   0x31
 136 #define EM28XX_R32_VSCALELOW    0x32
 137 #define EM28XX_R33_VSCALEHIGH   0x33
 138
 139 #define EM28XX_R40_AC97LSB      0x40
 140 #define EM28XX_R41_AC97MSB      0x41
 141 #define EM28XX_R42_AC97ADDR     0x42
 142 #define EM28XX_R43_AC97BUSY     0x43
 143
 144 #define EM28XX_R45_IR           0x45
 145         /* 0x45  bit 7    - parity bit
 146                  bits 6-0 - count
 147            0x46  IR brand
 148            0x47  IR data
 149          */
 150
 151 /* em2874 registers */
 152 #define EM2874_R50_IR_CONFIG    0x50
 153 #define EM2874_R51_IR           0x51
 154 #define EM2874_R5F_TS_ENABLE    0x5f
 155 #define EM2874_R80_GPIO         0x80
 156
 157 /* em2874 IR config register (0x50) */
 158 #define EM2874_IR_NEC           0x00
 159 #define EM2874_IR_RC5           0x04
 160 #define EM2874_IR_RC5_MODE_0    0x08
 161 #define EM2874_IR_RC5_MODE_6A   0x0b
 162
 163 /* em2874 Transport Stream Enable Register (0x5f) */
 164 #define EM2874_TS1_CAPTURE_ENABLE (1 << 0)
 165 #define EM2874_TS1_FILTER_ENABLE  (1 << 1)
 166 #define EM2874_TS1_NULL_DISCARD   (1 << 2)
 167 #define EM2874_TS2_CAPTURE_ENABLE (1 << 4)
 168 #define EM2874_TS2_FILTER_ENABLE  (1 << 5)
 169 #define EM2874_TS2_NULL_DISCARD   (1 << 6)
 170
 171 /* register settings */
 172 #define EM2800_AUDIO_SRC_TUNER  0x0d
 173 #define EM2800_AUDIO_SRC_LINE   0x0c
 174 #define EM28XX_AUDIO_SRC_TUNER  0xc0
 175 #define EM28XX_AUDIO_SRC_LINE   0x80
 176
 177 /* FIXME: Need to be populated with the other chip ID's */
 178 enum em28xx_chip_id {
 179         CHIP_ID_EM2820 = 18,    /* Also used by em2710 */
 180         CHIP_ID_EM2840 = 20,
 181         CHIP_ID_EM2750 = 33,
 182         CHIP_ID_EM2860 = 34,
 183         CHIP_ID_EM2870 = 35,
 184         CHIP_ID_EM2883 = 36,
 185         CHIP_ID_EM2874 = 65,
 186 };
 187
 188 /*
 189  * Registers used by em202 and other AC97 chips
 190  */
 191
 192 /* Standard AC97 registers */
 193 #define AC97_RESET               0x00
 194
 195         /* Output volumes */
 196 #define AC97_MASTER_VOL          0x02
 197 #define AC97_LINE_LEVEL_VOL      0x04   /* Some devices use for headphones */
 198 #define AC97_MASTER_MONO_VOL     0x06
 199
 200         /* Input volumes */
 201 #define AC97_PC_BEEP_VOL         0x0a
 202 #define AC97_PHONE_VOL           0x0c
 203 #define AC97_MIC_VOL             0x0e
 204 #define AC97_LINEIN_VOL          0x10
 205 #define AC97_CD_VOL              0x12
 206 #define AC97_VIDEO_VOL           0x14
 207 #define AC97_AUX_VOL             0x16
 208 #define AC97_PCM_OUT_VOL         0x18
 209
 210         /* capture registers */
 211 #define AC97_RECORD_SELECT       0x1a
 212 #define AC97_RECORD_GAIN         0x1c
 213
 214         /* control registers */
 215 #define AC97_GENERAL_PURPOSE     0x20
 216 #define AC97_3D_CTRL             0x22
 217 #define AC97_AUD_INT_AND_PAG     0x24
 218 #define AC97_POWER_DOWN_CTRL     0x26
 219 #define AC97_EXT_AUD_ID          0x28
 220 #define AC97_EXT_AUD_CTRL        0x2a
 221
 222 /* Supported rate varies for each AC97 device
 223    if write an unsupported value, it will return the closest one
 224  */
 225 #define AC97_PCM_OUT_FRONT_SRATE 0x2c
 226 #define AC97_PCM_OUT_SURR_SRATE  0x2e
 227 #define AC97_PCM_OUT_LFE_SRATE   0x30
 228 #define AC97_PCM_IN_SRATE        0x32
 229
 230         /* For devices with more than 2 channels, extra output volumes */
 231 #define AC97_LFE_MASTER_VOL      0x36
 232 #define AC97_SURR_MASTER_VOL     0x38
 233
 234         /* Digital SPDIF output control */
 235 #define AC97_SPDIF_OUT_CTRL      0x3a
 236
 237         /* Vendor ID identifier */
 238 #define AC97_VENDOR_ID1          0x7c
 239 #define AC97_VENDOR_ID2          0x7e
 240
 241 /* EMP202 vendor registers */
 242 #define EM202_EXT_MODEM_CTRL     0x3e
 243 #define EM202_GPIO_CONF          0x4c
 244 #define EM202_GPIO_POLARITY      0x4e
 245 #define EM202_GPIO_STICKY        0x50
 246 #define EM202_GPIO_MASK          0x52
 247 #define EM202_GPIO_STATUS        0x54
 248 #define EM202_SPDIF_OUT_SEL      0x6a
 249 #define EM202_ANTIPOP            0x72
 250 #define EM202_EAPD_GPIO_ACCESS   0x74