drivers/mfd/Kconfig

   1 #
   2 # Multifunction miscellaneous devices
   3 #
   4
   5 menuconfig MFD_SUPPORT
   6         bool "Multifunction device drivers"
   7         depends on HAS_IOMEM
   8         default y
   9         help
  10           Multifunction devices embed several functions (e.g. GPIOs,
  11           touchscreens, keyboards, current regulators, power management chips,
  12           etc...) in one single integrated circuit. They usually talk to the
  13           main CPU through one or more IRQ lines and low speed data busses (SPI,
  14           I2C, etc..). They appear as one single device to the main system
  15           through the data bus and the MFD framework allows for sub devices
  16           (a.k.a. functions) to appear as discrete platform devices.
  17           MFDs are typically found on embedded platforms.
  18
  19           This option alone does not add any kernel code.
  20
  21 if MFD_SUPPORT
  22
  23 config MFD_CORE
  24         tristate
  25         default n
  26
  27 config MFD_88PM860X
  28         bool "Support Marvell 88PM8606/88PM8607"
  29         depends on I2C=y && GENERIC_HARDIRQS
  30         select MFD_CORE
  31         help
  32           This supports for Marvell 88PM8606/88PM8607 Power Management IC.
  33           This includes the I2C driver and the core APIs _only_, you have to
  34           select individual components like voltage regulators, RTC and
  35           battery-charger under the corresponding menus.
  36
  37 config MFD_SM501
  38         tristate "Support for Silicon Motion SM501"
  39          ---help---
  40           This is the core driver for the Silicon Motion SM501 multimedia
  41           companion chip. This device is a multifunction device which may
  42           provide numerous interfaces including USB host controller, USB gadget,
  43           asynchronous serial ports, audio functions, and a dual display video
  44           interface. The device may be connected by PCI or local bus with
  45           varying functions enabled.
  46
  47 config MFD_SM501_GPIO
  48         bool "Export GPIO via GPIO layer"
  49         depends on MFD_SM501 && GPIOLIB
  50          ---help---
  51          This option uses the gpio library layer to export the 64 GPIO
  52          lines on the SM501. The platform data is used to supply the
  53          base number for the first GPIO line to register.
  54
  55 config MFD_ASIC3
  56         bool "Support for Compaq ASIC3"
  57         depends on GENERIC_HARDIRQS && GPIOLIB && ARM
  58         select MFD_CORE
  59          ---help---
  60           This driver supports the ASIC3 multifunction chip found on many
  61           PDAs (mainly iPAQ and HTC based ones)
  62
  63 config MFD_SH_MOBILE_SDHI
  64         bool "Support for SuperH Mobile SDHI"
  65         depends on SUPERH || ARCH_SHMOBILE
  66         select MFD_CORE
  67         select TMIO_MMC_DMA
  68          ---help---
  69           This driver supports the SDHI hardware block found in many
  70           SuperH Mobile SoCs.
  71
  72 config MFD_DAVINCI_VOICECODEC
  73         tristate
  74         select MFD_CORE
  75
  76 config MFD_DM355EVM_MSP
  77         bool "DaVinci DM355 EVM microcontroller"
  78         depends on I2C && MACH_DAVINCI_DM355_EVM
  79         help
  80           This driver supports the MSP430 microcontroller used on these
  81           boards.  MSP430 firmware manages resets and power sequencing,
  82           inputs from buttons and the IR remote, LEDs, an RTC, and more.
  83
  84 config HTC_EGPIO
  85         bool "HTC EGPIO support"
  86         depends on GENERIC_HARDIRQS && GPIOLIB && ARM
  87         help
  88             This driver supports the CPLD egpio chip present on
  89             several HTC phones.  It provides basic support for input
  90             pins, output pins, and irqs.
  91
  92 config HTC_PASIC3
  93         tristate "HTC PASIC3 LED/DS1WM chip support"
  94         select MFD_CORE
  95         help
  96           This core driver provides register access for the LED/DS1WM
  97           chips labeled "AIC2" and "AIC3", found on HTC Blueangel and
  98           HTC Magician devices, respectively. Actual functionality is
  99           handled by the leds-pasic3 and ds1wm drivers.
 100
 101 config HTC_I2CPLD
 102         bool "HTC I2C PLD chip support"
 103         depends on I2C=y && GPIOLIB
 104         help
 105           If you say yes here you get support for the supposed CPLD
 106           found on omap850 HTC devices like the HTC Wizard and HTC Herald.
 107           This device provides input and output GPIOs through an I2C
 108           interface to one or more sub-chips.
 109
 110 config UCB1400_CORE
 111         tristate "Philips UCB1400 Core driver"
 112         depends on AC97_BUS
 113         depends on GPIOLIB
 114         help
 115           This enables support for the Philips UCB1400 core functions.
 116           The UCB1400 is an AC97 audio codec.
 117
 118           To compile this driver as a module, choose M here: the
 119           module will be called ucb1400_core.
 120
 121 config TPS65010
 122         tristate "TPS6501x Power Management chips"
 123         depends on I2C && GPIOLIB
 124         default y if MACH_OMAP_H2 || MACH_OMAP_H3 || MACH_OMAP_OSK
 125         help
 126           If you say yes here you get support for the TPS6501x series of
 127           Power Management chips.  These include voltage regulators,
 128           lithium ion/polymer battery charging, and other features that
 129           are often used in portable devices like cell phones and cameras.
 130
 131           This driver can also be built as a module.  If so, the module
 132           will be called tps65010.
 133
 134 config TPS6507X
 135         tristate "TPS6507x Power Management / Touch Screen chips"
 136         select MFD_CORE
 137         depends on I2C
 138         help
 139           If you say yes here you get support for the TPS6507x series of
 140           Power Management / Touch Screen chips.  These include voltage
 141           regulators, lithium ion/polymer battery charging, touch screen
 142           and other features that are often used in portable devices.
 143           This driver can also be built as a module.  If so, the module
 144           will be called tps6507x.
 145
 146 config MENELAUS
 147         bool "Texas Instruments TWL92330/Menelaus PM chip"
 148         depends on I2C=y && ARCH_OMAP2
 149         help
 150           If you say yes here you get support for the Texas Instruments
 151           TWL92330/Menelaus Power Management chip. This include voltage
 152           regulators, Dual slot memory card transceivers, real-time clock
 153           and other features that are often used in portable devices like
 154           cell phones and PDAs.
 155
 156 config TWL4030_CORE
 157         bool "Texas Instruments TWL4030/TWL5030/TWL6030/TPS659x0 Support"
 158         depends on I2C=y && GENERIC_HARDIRQS
 159         help
 160           Say yes here if you have TWL4030 / TWL6030 family chip on your board.
 161           This core driver provides register access and IRQ handling
 162           facilities, and registers devices for the various functions
 163           so that function-specific drivers can bind to them.
 164
 165           These multi-function chips are found on many OMAP2 and OMAP3
 166           boards, providing power management, RTC, GPIO, keypad, a
 167           high speed USB OTG transceiver, an audio codec (on most
 168           versions) and many other features.
 169
 170 config TWL4030_POWER
 171         bool "Support power resources on TWL4030 family chips"
 172         depends on TWL4030_CORE && ARM
 173         help
 174           Say yes here if you want to use the power resources on the
 175           TWL4030 family chips.  Most of these resources are regulators,
 176           which have a separate driver; some are control signals, such
 177           as clock request handshaking.
 178
 179           This driver uses board-specific data to initialize the resources
 180           and load scripts controling which resources are switched off/on
 181           or reset when a sleep, wakeup or warm reset event occurs.
 182
 183 config TWL4030_CODEC
 184         bool
 185         depends on TWL4030_CORE
 186         select MFD_CORE
 187         default n
 188
 189 config TWL6030_PWM
 190         tristate "TWL6030 PWM (Pulse Width Modulator) Support"
 191         depends on TWL4030_CORE
 192         select HAVE_PWM
 193         default n
 194         help
 195           Say yes here if you want support for TWL6030 PWM.
 196           This is used to control charging LED brightness.
 197
 198 config MFD_STMPE
 199         bool "Support STMicroelectronics STMPE"
 200         depends on I2C=y && GENERIC_HARDIRQS
 201         select MFD_CORE
 202         help
 203           Support for the STMPE family of I/O Expanders from
 204           STMicroelectronics.
 205
 206           Currently supported devices are:
 207
 208                 STMPE811: GPIO, Touchscreen
 209                 STMPE1601: GPIO, Keypad
 210                 STMPE2401: GPIO, Keypad
 211                 STMPE2403: GPIO, Keypad
 212
 213           This driver provides common support for accessing the device,
 214           additional drivers must be enabled in order to use the functionality
 215           of the device.  Currently available sub drivers are:
 216
 217                 GPIO: stmpe-gpio
 218                 Keypad: stmpe-keypad
 219                 Touchscreen: stmpe-ts
 220
 221 config MFD_TC35892
 222         bool "Support Toshiba TC35892"
 223         depends on I2C=y && GENERIC_HARDIRQS
 224         select MFD_CORE
 225         help
 226           Support for the Toshiba TC35892 I/O Expander.
 227
 228           This driver provides common support for accessing the device,
 229           additional drivers must be enabled in order to use the
 230           functionality of the device.
 231
 232 config MFD_TMIO
 233         bool
 234         default n
 235
 236 config TMIO_MMC_DMA
 237         bool
 238         select DMA_ENGINE
 239         select DMADEVICES
 240
 241 config MFD_T7L66XB
 242         bool "Support Toshiba T7L66XB"
 243         depends on ARM && HAVE_CLK
 244         select MFD_CORE
 245         select MFD_TMIO
 246         help
 247           Support for Toshiba Mobile IO Controller T7L66XB
 248
 249 config MFD_TC6387XB
 250         bool "Support Toshiba TC6387XB"
 251         depends on ARM && HAVE_CLK
 252         select MFD_CORE
 253         select MFD_TMIO
 254         help
 255           Support for Toshiba Mobile IO Controller TC6387XB
 256
 257 config MFD_TC6393XB
 258         bool "Support Toshiba TC6393XB"
 259         depends on GPIOLIB && ARM
 260         select MFD_CORE
 261         select MFD_TMIO
 262         help
 263           Support for Toshiba Mobile IO Controller TC6393XB
 264
 265 config PMIC_DA903X
 266         bool "Dialog Semiconductor DA9030/DA9034 PMIC Support"
 267         depends on I2C=y
 268         help
 269           Say yes here to support for Dialog Semiconductor DA9030 (a.k.a
 270           ARAVA) and DA9034 (a.k.a MICCO), these are Power Management IC
 271           usually found on PXA processors-based platforms. This includes
 272           the I2C driver and the core APIs _only_, you have to select
 273           individual components like LCD backlight, voltage regulators,
 274           LEDs and battery-charger under the corresponding menus.
 275
 276 config PMIC_ADP5520
 277         bool "Analog Devices ADP5520/01 MFD PMIC Core Support"
 278         depends on I2C=y
 279         help
 280           Say yes here to add support for Analog Devices AD5520 and ADP5501,
 281           Multifunction Power Management IC. This includes
 282           the I2C driver and the core APIs _only_, you have to select
 283           individual components like LCD backlight, LEDs, GPIOs and Kepad
 284           under the corresponding menus.
 285
 286 config MFD_MAX8925
 287         bool "Maxim Semiconductor MAX8925 PMIC Support"
 288         depends on I2C=y && GENERIC_HARDIRQS
 289         select MFD_CORE
 290         help
 291           Say yes here to support for Maxim Semiconductor MAX8925. This is
 292           a Power Management IC. This driver provies common support for
 293           accessing the device, additional drivers must be enabled in order
 294           to use the functionality of the device.
 295
 296 config MFD_MAX8998
 297         bool "Maxim Semiconductor MAX8998/National LP3974 PMIC Support"
 298         depends on I2C=y && GENERIC_HARDIRQS
 299         select MFD_CORE
 300         help
 301           Say yes here to support for Maxim Semiconductor MAX8998 and
 302           National Semiconductor LP3974. This is a Power Management IC.
 303           This driver provies common support for accessing the device,
 304           additional drivers must be enabled in order to use the functionality
 305           of the device.
 306
 307 config MFD_WM8400
 308         tristate "Support Wolfson Microelectronics WM8400"
 309         select MFD_CORE
 310         depends on I2C
 311         help
 312           Support for the Wolfson Microelecronics WM8400 PMIC and audio
 313           CODEC.  This driver provides common support for accessing
 314           the device, additional drivers must be enabled in order to use
 315           the functionality of the device.
 316
 317 config MFD_WM831X
 318         bool "Support Wolfson Microelectronics WM831x/2x PMICs"
 319         select MFD_CORE
 320         depends on I2C=y && GENERIC_HARDIRQS
 321         help
 322           Support for the Wolfson Microelecronics WM831x and WM832x PMICs.
 323           This driver provides common support for accessing the device,
 324           additional drivers must be enabled in order to use the
 325           functionality of the device.
 326
 327 config MFD_WM8350
 328         bool
 329         depends on GENERIC_HARDIRQS
 330
 331 config MFD_WM8350_CONFIG_MODE_0
 332         bool
 333         depends on MFD_WM8350
 334
 335 config MFD_WM8350_CONFIG_MODE_1
 336         bool
 337         depends on MFD_WM8350
 338
 339 config MFD_WM8350_CONFIG_MODE_2
 340         bool
 341         depends on MFD_WM8350
 342
 343 config MFD_WM8350_CONFIG_MODE_3
 344         bool
 345         depends on MFD_WM8350
 346
 347 config MFD_WM8351_CONFIG_MODE_0
 348         bool
 349         depends on MFD_WM8350
 350
 351 config MFD_WM8351_CONFIG_MODE_1
 352         bool
 353         depends on MFD_WM8350
 354
 355 config MFD_WM8351_CONFIG_MODE_2
 356         bool
 357         depends on MFD_WM8350
 358
 359 config MFD_WM8351_CONFIG_MODE_3
 360         bool
 361         depends on MFD_WM8350
 362
 363 config MFD_WM8352_CONFIG_MODE_0
 364         bool
 365         depends on MFD_WM8350
 366
 367 config MFD_WM8352_CONFIG_MODE_1
 368         bool
 369         depends on MFD_WM8350
 370
 371 config MFD_WM8352_CONFIG_MODE_2
 372         bool
 373         depends on MFD_WM8350
 374
 375 config MFD_WM8352_CONFIG_MODE_3
 376         bool
 377         depends on MFD_WM8350
 378
 379 config MFD_WM8350_I2C
 380         bool "Support Wolfson Microelectronics WM8350 with I2C"
 381         select MFD_WM8350
 382         depends on I2C=y && GENERIC_HARDIRQS
 383         help
 384           The WM8350 is an integrated audio and power management
 385           subsystem with watchdog and RTC functionality for embedded
 386           systems.  This option enables core support for the WM8350 with
 387           I2C as the control interface.  Additional options must be
 388           selected to enable support for the functionality of the chip.
 389
 390 config MFD_WM8994
 391         bool "Support Wolfson Microelectronics WM8994"
 392         select MFD_CORE
 393         depends on I2C=y && GENERIC_HARDIRQS
 394         help
 395           The WM8994 is a highly integrated hi-fi CODEC designed for
 396           smartphone applicatiosn.  As well as audio functionality it
 397           has on board GPIO and regulator functionality which is
 398           supported via the relevant subsystems.  This driver provides
 399           core support for the WM8994, in order to use the actual
 400           functionaltiy of the device other drivers must be enabled.
 401
 402 config MFD_PCF50633
 403         tristate "Support for NXP PCF50633"
 404         depends on I2C
 405         help
 406           Say yes here if you have NXP PCF50633 chip on your board.
 407           This core driver provides register access and IRQ handling
 408           facilities, and registers devices for the various functions
 409           so that function-specific drivers can bind to them.
 410
 411 config MFD_MC13783
 412         tristate "Support Freescale MC13783"
 413         depends on SPI_MASTER
 414         select MFD_CORE
 415         help
 416           Support for the Freescale (Atlas) MC13783 PMIC and audio CODEC.
 417           This driver provides common support for accessing  the device,
 418           additional drivers must be enabled in order to use the
 419           functionality of the device.
 420
 421 config PCF50633_ADC
 422         tristate "Support for NXP PCF50633 ADC"
 423         depends on MFD_PCF50633
 424         help
 425          Say yes here if you want to include support for ADC in the
 426          NXP PCF50633 chip.
 427
 428 config PCF50633_GPIO
 429         tristate "Support for NXP PCF50633 GPIO"
 430         depends on MFD_PCF50633
 431         help
 432          Say yes here if you want to include support GPIO for pins on
 433          the PCF50633 chip.
 434
 435 config ABX500_CORE
 436         bool "ST-Ericsson ABX500 Mixed Signal Circuit register functions"
 437         default y if ARCH_U300 || ARCH_U8500
 438         help
 439           Say yes here if you have the ABX500 Mixed Signal IC family
 440           chips. This core driver expose register access functions.
 441           Functionality specific drivers using these functions can
 442           remain unchanged when IC changes. Binding of the functions to
 443           actual register access is done by the IC core driver.
 444
 445 config AB3100_CORE
 446         bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions"
 447         depends on I2C=y && ABX500_CORE
 448         select MFD_CORE
 449         default y if ARCH_U300
 450         help
 451           Select this to enable the AB3100 Mixed Signal IC core
 452           functionality. This connects to a AB3100 on the I2C bus
 453           and expose a number of symbols needed for dependent devices
 454           to read and write registers and subscribe to events from
 455           this multi-functional IC. This is needed to use other features
 456           of the AB3100 such as battery-backed RTC, charging control,
 457           LEDs, vibrator, system power and temperature, power management
 458           and ALSA sound.
 459
 460 config AB3100_OTP
 461         tristate "ST-Ericsson AB3100 OTP functions"
 462         depends on AB3100_CORE
 463         default y if AB3100_CORE
 464         help
 465           Select this to enable the AB3100 Mixed Signal IC OTP (one-time
 466           programmable memory) support. This exposes a sysfs file to read
 467           out OTP values.
 468
 469 config EZX_PCAP
 470         bool "PCAP Support"
 471         depends on GENERIC_HARDIRQS && SPI_MASTER
 472         help
 473           This enables the PCAP ASIC present on EZX Phones. This is
 474           needed for MMC, TouchScreen, Sound, USB, etc..
 475
 476 config AB8500_CORE
 477         bool "ST-Ericsson AB8500 Mixed Signal Power Management chip"
 478         depends on SPI=y && GENERIC_HARDIRQS && ABX500_CORE
 479         select MFD_CORE
 480         help
 481           Select this option to enable access to AB8500 power management
 482           chip. This connects to U8500 on the SSP/SPI bus and exports
 483           read/write functions for the devices to get access to this chip.
 484           This chip embeds various other multimedia funtionalities as well.
 485
 486 config AB8500_DEBUG
 487        bool "Enable debug info via debugfs"
 488        depends on AB8500_CORE && DEBUG_FS
 489        default y if DEBUG_FS
 490        help
 491          Select this option if you want debug information using the debug
 492          filesystem, debugfs.
 493
 494 config AB3550_CORE
 495         bool "ST-Ericsson AB3550 Mixed Signal Circuit core functions"
 496         select MFD_CORE
 497         depends on I2C=y && GENERIC_HARDIRQS && ABX500_CORE
 498         help
 499           Select this to enable the AB3550 Mixed Signal IC core
 500           functionality. This connects to a AB3550 on the I2C bus
 501           and expose a number of symbols needed for dependent devices
 502           to read and write registers and subscribe to events from
 503           this multi-functional IC. This is needed to use other features
 504           of the AB3550 such as battery-backed RTC, charging control,
 505           LEDs, vibrator, system power and temperature, power management
 506           and ALSA sound.
 507
 508 config MFD_TIMBERDALE
 509         tristate "Support for the Timberdale FPGA"
 510         select MFD_CORE
 511         depends on PCI && GPIOLIB
 512         ---help---
 513         This is the core driver for the timberdale FPGA. This device is a
 514         multifunction device which exposes numerous platform devices.
 515
 516         The timberdale FPGA can be found on the Intel Atom development board
 517         for in-vehicle infontainment, called Russellville.
 518
 519 config LPC_SCH
 520         tristate "Intel SCH LPC"
 521         depends on PCI
 522         select MFD_CORE
 523         help
 524           LPC bridge function of the Intel SCH provides support for
 525           System Management Bus and General Purpose I/O.
 526
 527 config MFD_RDC321X
 528         tristate "Support for RDC-R321x southbridge"
 529         select MFD_CORE
 530         depends on PCI
 531         help
 532           Say yes here if you want to have support for the RDC R-321x SoC
 533           southbridge which provides access to GPIOs and Watchdog using the
 534           southbridge PCI device configuration space.
 535
 536 config MFD_JANZ_CMODIO
 537         tristate "Support for Janz CMOD-IO PCI MODULbus Carrier Board"
 538         select MFD_CORE
 539         depends on PCI
 540         help
 541           This is the core driver for the Janz CMOD-IO PCI MODULbus
 542           carrier board. This device is a PCI to MODULbus bridge which may
 543           host many different types of MODULbus daughterboards, including
 544           CAN and GPIO controllers.
 545
 546 config MFD_JZ4740_ADC
 547         tristate "Support for the JZ4740 SoC ADC core"
 548         select MFD_CORE
 549         depends on MACH_JZ4740
 550         help
 551           Say yes here if you want support for the ADC unit in the JZ4740 SoC.
 552           This driver is necessary for jz4740-battery and jz4740-hwmon driver.
 553
 554 config MFD_TPS6586X
 555         tristate "TPS6586x Power Management chips"
 556         depends on I2C && GPIOLIB
 557         select MFD_CORE
 558         help
 559           If you say yes here you get support for the TPS6586X series of
 560           Power Management chips.
 561           This driver provides common support for accessing the device,
 562           additional drivers must be enabled in order to use the
 563           functionality of the device.
 564
 565           This driver can also be built as a module.  If so, the module
 566           will be called tps6586x.
 567
 568 endif # MFD_SUPPORT
 569
 570 menu "Multimedia Capabilities Port drivers"
 571         depends on ARCH_SA1100
 572
 573 config MCP
 574         tristate
 575
 576 # Interface drivers
 577 config MCP_SA11X0
 578         tristate "Support SA11x0 MCP interface"
 579         depends on ARCH_SA1100
 580         select MCP
 581
 582 # Chip drivers
 583 config MCP_UCB1200
 584         tristate "Support for UCB1200 / UCB1300"
 585         depends on MCP
 586
 587 config MCP_UCB1200_TS
 588         tristate "Touchscreen interface support"
 589         depends on MCP_UCB1200 && INPUT
 590
 591 endmenu