drivers/misc/Kconfig

   1 #
   2 # Misc strange devices
   3 #
   4
   5 menu "Misc devices"
   6
   7 config SENSORS_LIS3LV02D
   8         tristate
   9         depends on INPUT
  10         select INPUT_POLLDEV
  11         default n
  12
  13 config AD525X_DPOT
  14         tristate "Analog Devices Digital Potentiometers"
  15         depends on (I2C || SPI) && SYSFS
  16         help
  17           If you say yes here, you get support for the Analog Devices
  18           AD5258, AD5259, AD5251, AD5252, AD5253, AD5254, AD5255
  19           AD5160, AD5161, AD5162, AD5165, AD5200, AD5201, AD5203,
  20           AD5204, AD5206, AD5207, AD5231, AD5232, AD5233, AD5235,
  21           AD5260, AD5262, AD5263, AD5290, AD5291, AD5292, AD5293,
  22           AD7376, AD8400, AD8402, AD8403, ADN2850, AD5241, AD5242,
  23           AD5243, AD5245, AD5246, AD5247, AD5248, AD5280, AD5282,
  24           ADN2860, AD5273, AD5171, AD5170, AD5172, AD5173, AD5270,
  25           AD5271, AD5272, AD5274
  26           digital potentiometer chips.
  27
  28           See Documentation/misc-devices/ad525x_dpot.txt for the
  29           userspace interface.
  30
  31           This driver can also be built as a module.  If so, the module
  32           will be called ad525x_dpot.
  33
  34 config AD525X_DPOT_I2C
  35         tristate "support I2C bus connection"
  36         depends on AD525X_DPOT && I2C
  37         help
  38           Say Y here if you have a digital potentiometers hooked to an I2C bus.
  39
  40           To compile this driver as a module, choose M here: the
  41           module will be called ad525x_dpot-i2c.
  42
  43 config AD525X_DPOT_SPI
  44         tristate "support SPI bus connection"
  45         depends on AD525X_DPOT && SPI_MASTER
  46         help
  47           Say Y here if you have a digital potentiometers hooked to an SPI bus.
  48
  49           If unsure, say N (but it's safe to say "Y").
  50
  51           To compile this driver as a module, choose M here: the
  52           module will be called ad525x_dpot-spi.
  53
  54 config ATMEL_PWM
  55         tristate "Atmel AT32/AT91 PWM support"
  56         depends on HAVE_CLK
  57         depends on AVR32 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91SAM9G45
  58         help
  59           This option enables device driver support for the PWM channels
  60           on certain Atmel processors.  Pulse Width Modulation is used for
  61           purposes including software controlled power-efficient backlights
  62           on LCD displays, motor control, and waveform generation.
  63
  64 config ATMEL_TCLIB
  65         bool "Atmel AT32/AT91 Timer/Counter Library"
  66         depends on (AVR32 || ARCH_AT91)
  67         help
  68           Select this if you want a library to allocate the Timer/Counter
  69           blocks found on many Atmel processors.  This facilitates using
  70           these blocks by different drivers despite processor differences.
  71
  72 config ATMEL_TCB_CLKSRC
  73         bool "TC Block Clocksource"
  74         depends on ATMEL_TCLIB
  75         default y
  76         help
  77           Select this to get a high precision clocksource based on a
  78           TC block with a 5+ MHz base clock rate.  Two timer channels
  79           are combined to make a single 32-bit timer.
  80
  81           When GENERIC_CLOCKEVENTS is defined, the third timer channel
  82           may be used as a clock event device supporting oneshot mode
  83           (delays of up to two seconds) based on the 32 KiHz clock.
  84
  85 config ATMEL_TCB_CLKSRC_BLOCK
  86         int
  87         depends on ATMEL_TCB_CLKSRC
  88         prompt "TC Block" if ARCH_AT91RM9200 || ARCH_AT91SAM9260 || CPU_AT32AP700X
  89         default 0
  90         range 0 1
  91         help
  92           Some chips provide more than one TC block, so you have the
  93           choice of which one to use for the clock framework.  The other
  94           TC can be used for other purposes, such as PWM generation and
  95           interval timing.
  96
  97 config DUMMY_IRQ
  98         tristate "Dummy IRQ handler"
  99         default n
 100         ---help---
 101           This module accepts a single 'irq' parameter, which it should register for.
 102           The sole purpose of this module is to help with debugging of systems on
 103           which spurious IRQs would happen on disabled IRQ vector.
 104
 105 config IBM_ASM
 106         tristate "Device driver for IBM RSA service processor"
 107         depends on X86 && PCI && INPUT
 108         ---help---
 109           This option enables device driver support for in-band access to the
 110           IBM RSA (Condor) service processor in eServer xSeries systems.
 111           The ibmasm device driver allows user space application to access
 112           ASM (Advanced Systems Management) functions on the service
 113           processor. The driver is meant to be used in conjunction with
 114           a user space API.
 115           The ibmasm driver also enables the OS to use the UART on the
 116           service processor board as a regular serial port. To make use of
 117           this feature serial driver support (CONFIG_SERIAL_8250) must be
 118           enabled.
 119
 120           WARNING: This software may not be supported or function
 121           correctly on your IBM server. Please consult the IBM ServerProven
 122           website <http://www-03.ibm.com/systems/info/x86servers/serverproven/compat/us/>
 123           for information on the specific driver level and support statement
 124           for your IBM server.
 125
 126 config PHANTOM
 127         tristate "Sensable PHANToM (PCI)"
 128         depends on PCI
 129         help
 130           Say Y here if you want to build a driver for Sensable PHANToM device.
 131
 132           This driver is only for PCI PHANToMs.
 133
 134           If you choose to build module, its name will be phantom. If unsure,
 135           say N here.
 136
 137 config INTEL_MID_PTI
 138         tristate "Parallel Trace Interface for MIPI P1149.7 cJTAG standard"
 139         depends on PCI && TTY && (X86_INTEL_MID || COMPILE_TEST)
 140         default n
 141         help
 142           The PTI (Parallel Trace Interface) driver directs
 143           trace data routed from various parts in the system out
 144           through an Intel Penwell PTI port and out of the mobile
 145           device for analysis with a debugging tool (Lauterbach or Fido).
 146
 147           You should select this driver if the target kernel is meant for
 148           an Intel Atom (non-netbook) mobile device containing a MIPI
 149           P1149.7 standard implementation.
 150
 151 config SGI_IOC4
 152         tristate "SGI IOC4 Base IO support"
 153         depends on PCI
 154         ---help---
 155           This option enables basic support for the IOC4 chip on certain
 156           SGI IO controller cards (IO9, IO10, and PCI-RT).  This option
 157           does not enable any specific functions on such a card, but provides
 158           necessary infrastructure for other drivers to utilize.
 159
 160           If you have an SGI Altix with an IOC4-based card say Y.
 161           Otherwise say N.
 162
 163 config TIFM_CORE
 164         tristate "TI Flash Media interface support"
 165         depends on PCI
 166         help
 167           If you want support for Texas Instruments(R) Flash Media adapters
 168           you should select this option and then also choose an appropriate
 169           host adapter, such as 'TI Flash Media PCI74xx/PCI76xx host adapter
 170           support', if you have a TI PCI74xx compatible card reader, for
 171           example.
 172           You will also have to select some flash card format drivers. MMC/SD
 173           cards are supported via 'MMC/SD Card support: TI Flash Media MMC/SD
 174           Interface support (MMC_TIFM_SD)'.
 175
 176           To compile this driver as a module, choose M here: the module will
 177           be called tifm_core.
 178
 179 config TIFM_7XX1
 180         tristate "TI Flash Media PCI74xx/PCI76xx host adapter support"
 181         depends on PCI && TIFM_CORE
 182         default TIFM_CORE
 183         help
 184           This option enables support for Texas Instruments(R) PCI74xx and
 185           PCI76xx families of Flash Media adapters, found in many laptops.
 186           To make actual use of the device, you will have to select some
 187           flash card format drivers, as outlined in the TIFM_CORE Help.
 188
 189           To compile this driver as a module, choose M here: the module will
 190           be called tifm_7xx1.
 191
 192 config ICS932S401
 193         tristate "Integrated Circuits ICS932S401"
 194         depends on I2C
 195         help
 196           If you say yes here you get support for the Integrated Circuits
 197           ICS932S401 clock control chips.
 198
 199           This driver can also be built as a module. If so, the module
 200           will be called ics932s401.
 201
 202 config ATMEL_SSC
 203         tristate "Device driver for Atmel SSC peripheral"
 204         depends on HAS_IOMEM && (AVR32 || ARCH_AT91 || COMPILE_TEST)
 205         ---help---
 206           This option enables device driver support for Atmel Synchronized
 207           Serial Communication peripheral (SSC).
 208
 209           The SSC peripheral supports a wide variety of serial frame based
 210           communications, i.e. I2S, SPI, etc.
 211
 212           If unsure, say N.
 213
 214 config ENCLOSURE_SERVICES
 215         tristate "Enclosure Services"
 216         default n
 217         help
 218           Provides support for intelligent enclosures (bays which
 219           contain storage devices).  You also need either a host
 220           driver (SCSI/ATA) which supports enclosures
 221           or a SCSI enclosure device (SES) to use these services.
 222
 223 config SGI_XP
 224         tristate "Support communication between SGI SSIs"
 225         depends on NET
 226         depends on (IA64_GENERIC || IA64_SGI_SN2 || IA64_SGI_UV || X86_UV) && SMP
 227         select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
 228         select GENERIC_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
 229         select SGI_GRU if X86_64 && SMP
 230         ---help---
 231           An SGI machine can be divided into multiple Single System
 232           Images which act independently of each other and have
 233           hardware based memory protection from the others.  Enabling
 234           this feature will allow for direct communication between SSIs
 235           based on a network adapter and DMA messaging.
 236
 237 config CS5535_MFGPT
 238         tristate "CS5535/CS5536 Geode Multi-Function General Purpose Timer (MFGPT) support"
 239         depends on MFD_CS5535
 240         default n
 241         help
 242           This driver provides access to MFGPT functionality for other
 243           drivers that need timers.  MFGPTs are available in the CS5535 and
 244           CS5536 companion chips that are found in AMD Geode and several
 245           other platforms.  They have a better resolution and max interval
 246           than the generic PIT, and are suitable for use as high-res timers.
 247           You probably don't want to enable this manually; other drivers that
 248           make use of it should enable it.
 249
 250 config CS5535_MFGPT_DEFAULT_IRQ
 251         int
 252         depends on CS5535_MFGPT
 253         default 7
 254         help
 255           MFGPTs on the CS5535 require an interrupt.  The selected IRQ
 256           can be overridden as a module option as well as by driver that
 257           use the cs5535_mfgpt_ API; however, different architectures might
 258           want to use a different IRQ by default.  This is here for
 259           architectures to set as necessary.
 260
 261 config CS5535_CLOCK_EVENT_SRC
 262         tristate "CS5535/CS5536 high-res timer (MFGPT) events"
 263         depends on GENERIC_CLOCKEVENTS && CS5535_MFGPT
 264         help
 265           This driver provides a clock event source based on the MFGPT
 266           timer(s) in the CS5535 and CS5536 companion chips.
 267           MFGPTs have a better resolution and max interval than the
 268           generic PIT, and are suitable for use as high-res timers.
 269
 270 config HP_ILO
 271         tristate "Channel interface driver for the HP iLO processor"
 272         depends on PCI
 273         default n
 274         help
 275           The channel interface driver allows applications to communicate
 276           with iLO management processors present on HP ProLiant servers.
 277           Upon loading, the driver creates /dev/hpilo/dXccbN files, which
 278           can be used to gather data from the management processor, via
 279           read and write system calls.
 280
 281           To compile this driver as a module, choose M here: the
 282           module will be called hpilo.
 283
 284 config SGI_GRU
 285         tristate "SGI GRU driver"
 286         depends on X86_UV && SMP
 287         default n
 288         select MMU_NOTIFIER
 289         ---help---
 290         The GRU is a hardware resource located in the system chipset. The GRU
 291         contains memory that can be mmapped into the user address space. This memory is
 292         used to communicate with the GRU to perform functions such as load/store,
 293         scatter/gather, bcopy, AMOs, etc.  The GRU is directly accessed by user
 294         instructions using user virtual addresses. GRU instructions (ex., bcopy) use
 295         user virtual addresses for operands.
 296
 297         If you are not running on a SGI UV system, say N.
 298
 299 config SGI_GRU_DEBUG
 300         bool  "SGI GRU driver debug"
 301         depends on SGI_GRU
 302         default n
 303         ---help---
 304         This option enables additional debugging code for the SGI GRU driver.
 305         If you are unsure, say N.
 306
 307 config APDS9802ALS
 308         tristate "Medfield Avago APDS9802 ALS Sensor module"
 309         depends on I2C
 310         help
 311           If you say yes here you get support for the ALS APDS9802 ambient
 312           light sensor.
 313
 314           This driver can also be built as a module.  If so, the module
 315           will be called apds9802als.
 316
 317 config ISL29003
 318         tristate "Intersil ISL29003 ambient light sensor"
 319         depends on I2C && SYSFS
 320         help
 321           If you say yes here you get support for the Intersil ISL29003
 322           ambient light sensor.
 323
 324           This driver can also be built as a module.  If so, the module
 325           will be called isl29003.
 326
 327 config ISL29020
 328         tristate "Intersil ISL29020 ambient light sensor"
 329         depends on I2C
 330         help
 331           If you say yes here you get support for the Intersil ISL29020
 332           ambient light sensor.
 333
 334           This driver can also be built as a module.  If so, the module
 335           will be called isl29020.
 336
 337 config SENSORS_TSL2550
 338         tristate "Taos TSL2550 ambient light sensor"
 339         depends on I2C && SYSFS
 340         help
 341           If you say yes here you get support for the Taos TSL2550
 342           ambient light sensor.
 343
 344           This driver can also be built as a module.  If so, the module
 345           will be called tsl2550.
 346
 347 config SENSORS_BH1780
 348         tristate "ROHM BH1780GLI ambient light sensor"
 349         depends on I2C && SYSFS
 350         help
 351           If you say yes here you get support for the ROHM BH1780GLI
 352           ambient light sensor.
 353
 354           This driver can also be built as a module.  If so, the module
 355           will be called bh1780gli.
 356
 357 config SENSORS_BH1770
 358          tristate "BH1770GLC / SFH7770 combined ALS - Proximity sensor"
 359          depends on I2C
 360          ---help---
 361            Say Y here if you want to build a driver for BH1770GLC (ROHM) or
 362            SFH7770 (Osram) combined ambient light and proximity sensor chip.
 363
 364            To compile this driver as a module, choose M here: the
 365            module will be called bh1770glc. If unsure, say N here.
 366
 367 config SENSORS_APDS990X
 368          tristate "APDS990X combined als and proximity sensors"
 369          depends on I2C
 370          default n
 371          ---help---
 372            Say Y here if you want to build a driver for Avago APDS990x
 373            combined ambient light and proximity sensor chip.
 374
 375            To compile this driver as a module, choose M here: the
 376            module will be called apds990x. If unsure, say N here.
 377
 378 config HMC6352
 379         tristate "Honeywell HMC6352 compass"
 380         depends on I2C
 381         help
 382           This driver provides support for the Honeywell HMC6352 compass,
 383           providing configuration and heading data via sysfs.
 384
 385 config DS1682
 386         tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
 387         depends on I2C
 388         help
 389           If you say yes here you get support for Dallas Semiconductor
 390           DS1682 Total Elapsed Time Recorder.
 391
 392           This driver can also be built as a module.  If so, the module
 393           will be called ds1682.
 394
 395 config SPEAR13XX_PCIE_GADGET
 396         bool "PCIe gadget support for SPEAr13XX platform"
 397         depends on ARCH_SPEAR13XX && BROKEN
 398         default n
 399         help
 400          This option enables gadget support for PCIe controller. If
 401          board file defines any controller as PCIe endpoint then a sysfs
 402          entry will be created for that controller. User can use these
 403          sysfs node to configure PCIe EP as per his requirements.
 404
 405 config TI_DAC7512
 406         tristate "Texas Instruments DAC7512"
 407         depends on SPI && SYSFS
 408         help
 409           If you say yes here you get support for the Texas Instruments
 410           DAC7512 16-bit digital-to-analog converter.
 411
 412           This driver can also be built as a module. If so, the module
 413           will be called ti_dac7512.
 414
 415 config VMWARE_BALLOON
 416         tristate "VMware Balloon Driver"
 417         depends on X86 && HYPERVISOR_GUEST
 418         help
 419           This is VMware physical memory management driver which acts
 420           like a "balloon" that can be inflated to reclaim physical pages
 421           by reserving them in the guest and invalidating them in the
 422           monitor, freeing up the underlying machine pages so they can
 423           be allocated to other guests. The balloon can also be deflated
 424           to allow the guest to use more physical memory.
 425
 426           If unsure, say N.
 427
 428           To compile this driver as a module, choose M here: the
 429           module will be called vmw_balloon.
 430
 431 config ARM_CHARLCD
 432         bool "ARM Ltd. Character LCD Driver"
 433         depends on PLAT_VERSATILE
 434         help
 435           This is a driver for the character LCD found on the ARM Ltd.
 436           Versatile and RealView Platform Baseboards. It doesn't do
 437           very much more than display the text "ARM Linux" on the first
 438           line and the Linux version on the second line, but that's
 439           still useful.
 440
 441 config BMP085
 442         bool
 443         depends on SYSFS
 444
 445 config BMP085_I2C
 446         tristate "BMP085 digital pressure sensor on I2C"
 447         select BMP085
 448         select REGMAP_I2C
 449         depends on I2C && SYSFS
 450         help
 451           Say Y here if you want to support Bosch Sensortec's digital pressure
 452           sensor hooked to an I2C bus.
 453
 454           To compile this driver as a module, choose M here: the
 455           module will be called bmp085-i2c.
 456
 457 config BMP085_SPI
 458         tristate "BMP085 digital pressure sensor on SPI"
 459         select BMP085
 460         select REGMAP_SPI
 461         depends on SPI_MASTER && SYSFS
 462         help
 463           Say Y here if you want to support Bosch Sensortec's digital pressure
 464           sensor hooked to an SPI bus.
 465
 466           To compile this driver as a module, choose M here: the
 467           module will be called bmp085-spi.
 468
 469 config PCH_PHUB
 470         tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) PHUB"
 471         select GENERIC_NET_UTILS
 472         depends on PCI && (X86_32 || COMPILE_TEST)
 473         help
 474           This driver is for PCH(Platform controller Hub) PHUB(Packet Hub) of
 475           Intel Topcliff which is an IOH(Input/Output Hub) for x86 embedded
 476           processor. The Topcliff has MAC address and Option ROM data in SROM.
 477           This driver can access MAC address and Option ROM data in SROM.
 478
 479           This driver also can be used for LAPIS Semiconductor's IOH,
 480           ML7213/ML7223/ML7831.
 481           ML7213 which is for IVI(In-Vehicle Infotainment) use.
 482           ML7223 IOH is for MP(Media Phone) use.
 483           ML7831 IOH is for general purpose use.
 484           ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series.
 485           ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH.
 486
 487           To compile this driver as a module, choose M here: the module will
 488           be called pch_phub.
 489
 490 config USB_SWITCH_FSA9480
 491         tristate "FSA9480 USB Switch"
 492         depends on I2C
 493         help
 494           The FSA9480 is a USB port accessory detector and switch.
 495           The FSA9480 is fully controlled using I2C and enables USB data,
 496           stereo and mono audio, video, microphone and UART data to use
 497           a common connector port.
 498
 499 config LATTICE_ECP3_CONFIG
 500         tristate "Lattice ECP3 FPGA bitstream configuration via SPI"
 501         depends on SPI && SYSFS
 502         select FW_LOADER
 503         default n
 504         help
 505           This option enables support for bitstream configuration (programming
 506           or loading) of the Lattice ECP3 FPGA family via SPI.
 507
 508           If unsure, say N.
 509
 510 config SRAM
 511         bool "Generic on-chip SRAM driver"
 512         depends on HAS_IOMEM
 513         select GENERIC_ALLOCATOR
 514         help
 515           This driver allows you to declare a memory region to be managed by
 516           the genalloc API. It is supposed to be used for small on-chip SRAM
 517           areas found on many SoCs.
 518
 519 config VEXPRESS_SYSCFG
 520         bool "Versatile Express System Configuration driver"
 521         depends on VEXPRESS_CONFIG
 522         default y
 523         help
 524           ARM Ltd. Versatile Express uses specialised platform configuration
 525           bus. System Configuration interface is one of the possible means
 526           of generating transactions on this bus.
 527
 528 source "drivers/misc/c2port/Kconfig"
 529 source "drivers/misc/eeprom/Kconfig"
 530 source "drivers/misc/cb710/Kconfig"
 531 source "drivers/misc/ti-st/Kconfig"
 532 source "drivers/misc/lis3lv02d/Kconfig"
 533 source "drivers/misc/carma/Kconfig"
 534 source "drivers/misc/altera-stapl/Kconfig"
 535 source "drivers/misc/mei/Kconfig"
 536 source "drivers/misc/vmw_vmci/Kconfig"
 537 source "drivers/misc/mic/Kconfig"
 538 source "drivers/misc/genwqe/Kconfig"
 539 source "drivers/misc/echo/Kconfig"
 540 endmenu