drivers/net/Kconfig

   1 #
   2 # Network device configuration
   3 #
   4
   5 menuconfig NETDEVICES
   6         default y if UML
   7         depends on NET
   8         bool "Network device support"
   9         ---help---
  10           You can say N here if you don't intend to connect your Linux box to
  11           any other computer at all.
  12
  13           You'll have to say Y if your computer contains a network card that
  14           you want to use under Linux. If you are going to run SLIP or PPP over
  15           telephone line or null modem cable you need say Y here. Connecting
  16           two machines with parallel ports using PLIP needs this, as well as
  17           AX.25/KISS for sending Internet traffic over amateur radio links.
  18
  19           See also "The Linux Network Administrator's Guide" by Olaf Kirch and
  20           Terry Dawson. Available at <http://www.tldp.org/guides.html>.
  21
  22           If unsure, say Y.
  23
  24 # All the following symbols are dependent on NETDEVICES - do not repeat
  25 # that for each of the symbols.
  26 if NETDEVICES
  27
  28 config MII
  29         tristate
  30
  31 config NET_CORE
  32         default y
  33         bool "Network core driver support"
  34         ---help---
  35           You can say N here if you do not intend to use any of the
  36           networking core drivers (i.e. VLAN, bridging, bonding, etc.)
  37
  38 if NET_CORE
  39
  40 config BONDING
  41         tristate "Bonding driver support"
  42         depends on INET
  43         depends on IPV6 || IPV6=n
  44         ---help---
  45           Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
  46           Channels together. This is called 'Etherchannel' by Cisco,
  47           'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
  48
  49           The driver supports multiple bonding modes to allow for both high
  50           performance and high availability operation.
  51
  52           Refer to <file:Documentation/networking/bonding.txt> for more
  53           information.
  54
  55           To compile this driver as a module, choose M here: the module
  56           will be called bonding.
  57
  58 config DUMMY
  59         tristate "Dummy net driver support"
  60         ---help---
  61           This is essentially a bit-bucket device (i.e. traffic you send to
  62           this device is consigned into oblivion) with a configurable IP
  63           address. It is most commonly used in order to make your currently
  64           inactive SLIP address seem like a real address for local programs.
  65           If you use SLIP or PPP, you might want to say Y here. Since this
  66           thing often comes in handy, the default is Y. It won't enlarge your
  67           kernel either. What a deal. Read about it in the Network
  68           Administrator's Guide, available from
  69           <http://www.tldp.org/docs.html#guide>.
  70
  71           To compile this driver as a module, choose M here: the module
  72           will be called dummy.
  73
  74 config EQUALIZER
  75         tristate "EQL (serial line load balancing) support"
  76         ---help---
  77           If you have two serial connections to some other computer (this
  78           usually requires two modems and two telephone lines) and you use
  79           SLIP (the protocol for sending Internet traffic over telephone
  80           lines) or PPP (a better SLIP) on them, you can make them behave like
  81           one double speed connection using this driver.  Naturally, this has
  82           to be supported at the other end as well, either with a similar EQL
  83           Linux driver or with a Livingston Portmaster 2e.
  84
  85           Say Y if you want this and read
  86           <file:Documentation/networking/eql.txt>.  You may also want to read
  87           section 6.2 of the NET-3-HOWTO, available from
  88           <http://www.tldp.org/docs.html#howto>.
  89
  90           To compile this driver as a module, choose M here: the module
  91           will be called eql.  If unsure, say N.
  92
  93 config NET_FC
  94         bool "Fibre Channel driver support"
  95         depends on SCSI && PCI
  96         help
  97           Fibre Channel is a high speed serial protocol mainly used to connect
  98           large storage devices to the computer; it is compatible with and
  99           intended to replace SCSI.
 100
 101           If you intend to use Fibre Channel, you need to have a Fibre channel
 102           adaptor card in your computer; say Y here and to the driver for your
 103           adaptor below. You also should have said Y to "SCSI support" and
 104           "SCSI generic support".
 105
 106 config IFB
 107         tristate "Intermediate Functional Block support"
 108         depends on NET_CLS_ACT
 109         ---help---
 110           This is an intermediate driver that allows sharing of
 111           resources.
 112           To compile this driver as a module, choose M here: the module
 113           will be called ifb.  If you want to use more than one ifb
 114           device at a time, you need to compile this driver as a module.
 115           Instead of 'ifb', the devices will then be called 'ifb0',
 116           'ifb1' etc.
 117           Look at the iproute2 documentation directory for usage etc
 118
 119 source "drivers/net/team/Kconfig"
 120
 121 config MACVLAN
 122         tristate "MAC-VLAN support"
 123         ---help---
 124           This allows one to create virtual interfaces that map packets to
 125           or from specific MAC addresses to a particular interface.
 126
 127           Macvlan devices can be added using the "ip" command from the
 128           iproute2 package starting with the iproute2-2.6.23 release:
 129
 130           "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"
 131
 132           To compile this driver as a module, choose M here: the module
 133           will be called macvlan.
 134
 135 config MACVTAP
 136         tristate "MAC-VLAN based tap driver"
 137         depends on MACVLAN
 138         depends on INET
 139         help
 140           This adds a specialized tap character device driver that is based
 141           on the MAC-VLAN network interface, called macvtap. A macvtap device
 142           can be added in the same way as a macvlan device, using 'type
 143           macvtap', and then be accessed through the tap user space interface.
 144
 145           To compile this driver as a module, choose M here: the module
 146           will be called macvtap.
 147
 148
 149 config IPVLAN
 150     tristate "IP-VLAN support"
 151     depends on INET
 152     depends on IPV6
 153     ---help---
 154       This allows one to create virtual devices off of a main interface
 155       and packets will be delivered based on the dest L3 (IPv6/IPv4 addr)
 156       on packets. All interfaces (including the main interface) share L2
 157       making it transparent to the connected L2 switch.
 158
 159       Ipvlan devices can be added using the "ip" command from the
 160       iproute2 package starting with the iproute2-3.19 release:
 161
 162       "ip link add link <main-dev> [ NAME ] type ipvlan"
 163
 164       To compile this driver as a module, choose M here: the module
 165       will be called ipvlan.
 166
 167
 168 config VXLAN
 169        tristate "Virtual eXtensible Local Area Network (VXLAN)"
 170        depends on INET
 171        select NET_UDP_TUNNEL
 172        ---help---
 173           This allows one to create vxlan virtual interfaces that provide
 174           Layer 2 Networks over Layer 3 Networks. VXLAN is often used
 175           to tunnel virtual network infrastructure in virtualized environments.
 176           For more information see:
 177             http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-02
 178
 179           To compile this driver as a module, choose M here: the module
 180           will be called vxlan.
 181
 182 config GENEVE
 183        tristate "Generic Network Virtualization Encapsulation"
 184        depends on INET && NET_UDP_TUNNEL
 185        select NET_IP_TUNNEL
 186        ---help---
 187           This allows one to create geneve virtual interfaces that provide
 188           Layer 2 Networks over Layer 3 Networks. GENEVE is often used
 189           to tunnel virtual network infrastructure in virtualized environments.
 190           For more information see:
 191             http://tools.ietf.org/html/draft-gross-geneve-02
 192
 193           To compile this driver as a module, choose M here: the module
 194           will be called geneve.
 195
 196 config MACSEC
 197         tristate "IEEE 802.1AE MAC-level encryption (MACsec)"
 198         select CRYPTO
 199         select CRYPTO_AES
 200         select CRYPTO_GCM
 201         ---help---
 202            MACsec is an encryption standard for Ethernet.
 203
 204 config NETCONSOLE
 205         tristate "Network console logging support"
 206         ---help---
 207         If you want to log kernel messages over the network, enable this.
 208         See <file:Documentation/networking/netconsole.txt> for details.
 209
 210 config NETCONSOLE_DYNAMIC
 211         bool "Dynamic reconfiguration of logging targets"
 212         depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
 213                         !(NETCONSOLE=y && CONFIGFS_FS=m)
 214         help
 215           This option enables the ability to dynamically reconfigure target
 216           parameters (interface, IP addresses, port numbers, MAC addresses)
 217           at runtime through a userspace interface exported using configfs.
 218           See <file:Documentation/networking/netconsole.txt> for details.
 219
 220 config NETPOLL
 221         def_bool NETCONSOLE
 222         select SRCU
 223
 224 config NET_POLL_CONTROLLER
 225         def_bool NETPOLL
 226
 227 config NTB_NETDEV
 228         tristate "Virtual Ethernet over NTB Transport"
 229         depends on NTB_TRANSPORT
 230
 231 config RIONET
 232         tristate "RapidIO Ethernet over messaging driver support"
 233         depends on RAPIDIO
 234
 235 config RIONET_TX_SIZE
 236         int "Number of outbound queue entries"
 237         depends on RIONET
 238         default "128"
 239
 240 config RIONET_RX_SIZE
 241         int "Number of inbound queue entries"
 242         depends on RIONET
 243         default "128"
 244
 245 config TUN
 246         tristate "Universal TUN/TAP device driver support"
 247         depends on INET
 248         select CRC32
 249         ---help---
 250           TUN/TAP provides packet reception and transmission for user space
 251           programs.  It can be viewed as a simple Point-to-Point or Ethernet
 252           device, which instead of receiving packets from a physical media,
 253           receives them from user space program and instead of sending packets
 254           via physical media writes them to the user space program.
 255
 256           When a program opens /dev/net/tun, driver creates and registers
 257           corresponding net device tunX or tapX.  After a program closed above
 258           devices, driver will automatically delete tunXX or tapXX device and
 259           all routes corresponding to it.
 260
 261           Please read <file:Documentation/networking/tuntap.txt> for more
 262           information.
 263
 264           To compile this driver as a module, choose M here: the module
 265           will be called tun.
 266
 267           If you don't know what to use this for, you don't need it.
 268
 269 config TUN_VNET_CROSS_LE
 270         bool "Support for cross-endian vnet headers on little-endian kernels"
 271         default n
 272         ---help---
 273           This option allows TUN/TAP and MACVTAP device drivers in a
 274           little-endian kernel to parse vnet headers that come from a
 275           big-endian legacy virtio device.
 276
 277           Userspace programs can control the feature using the TUNSETVNETBE
 278           and TUNGETVNETBE ioctls.
 279
 280           Unless you have a little-endian system hosting a big-endian virtual
 281           machine with a legacy virtio NIC, you should say N.
 282
 283 config VETH
 284         tristate "Virtual ethernet pair device"
 285         ---help---
 286           This device is a local ethernet tunnel. Devices are created in pairs.
 287           When one end receives the packet it appears on its pair and vice
 288           versa.
 289
 290 config VIRTIO_NET
 291         tristate "Virtio network driver"
 292         depends on VIRTIO
 293         ---help---
 294           This is the virtual network driver for virtio.  It can be used with
 295           lguest or QEMU based VMMs (like KVM or Xen).  Say Y or M.
 296
 297 config NLMON
 298         tristate "Virtual netlink monitoring device"
 299         ---help---
 300           This option enables a monitoring net device for netlink skbs. The
 301           purpose of this is to analyze netlink messages with packet sockets.
 302           Thus applications like tcpdump will be able to see local netlink
 303           messages if they tap into the netlink device, record pcaps for further
 304           diagnostics, etc. This is mostly intended for developers or support
 305           to debug netlink issues. If unsure, say N.
 306
 307 config NET_VRF
 308         tristate "Virtual Routing and Forwarding (Lite)"
 309         depends on IP_MULTIPLE_TABLES
 310         depends on NET_L3_MASTER_DEV
 311         depends on IPV6 || IPV6=n
 312         depends on IPV6_MULTIPLE_TABLES || IPV6=n
 313         ---help---
 314           This option enables the support for mapping interfaces into VRF's. The
 315           support enables VRF devices.
 316
 317 endif # NET_CORE
 318
 319 config SUNGEM_PHY
 320         tristate
 321
 322 source "drivers/net/arcnet/Kconfig"
 323
 324 source "drivers/atm/Kconfig"
 325
 326 source "drivers/net/caif/Kconfig"
 327
 328 source "drivers/net/dsa/Kconfig"
 329
 330 source "drivers/net/ethernet/Kconfig"
 331
 332 source "drivers/net/fddi/Kconfig"
 333
 334 source "drivers/net/hippi/Kconfig"
 335
 336 config NET_SB1000
 337         tristate "General Instruments Surfboard 1000"
 338         depends on PNP
 339         ---help---
 340           This is a driver for the General Instrument (also known as
 341           NextLevel) SURFboard 1000 internal
 342           cable modem. This is an ISA card which is used by a number of cable
 343           TV companies to provide cable modem access. It's a one-way
 344           downstream-only cable modem, meaning that your upstream net link is
 345           provided by your regular phone modem.
 346
 347           At present this driver only compiles as a module, so say M here if
 348           you have this card. The module will be called sb1000. Then read
 349           <file:Documentation/networking/README.sb1000> for information on how
 350           to use this module, as it needs special ppp scripts for establishing
 351           a connection. Further documentation and the necessary scripts can be
 352           found at:
 353
 354           <http://www.jacksonville.net/~fventuri/>
 355           <http://home.adelphia.net/~siglercm/sb1000.html>
 356           <http://linuxpower.cx/~cable/>
 357
 358           If you don't have this card, of course say N.
 359
 360 source "drivers/net/phy/Kconfig"
 361
 362 source "drivers/net/plip/Kconfig"
 363
 364 source "drivers/net/ppp/Kconfig"
 365
 366 source "drivers/net/slip/Kconfig"
 367
 368 source "drivers/s390/net/Kconfig"
 369
 370 source "drivers/net/usb/Kconfig"
 371
 372 source "drivers/net/wireless/Kconfig"
 373
 374 source "drivers/net/wimax/Kconfig"
 375
 376 source "drivers/net/wan/Kconfig"
 377
 378 source "drivers/net/ieee802154/Kconfig"
 379
 380 config XEN_NETDEV_FRONTEND
 381         tristate "Xen network device frontend driver"
 382         depends on XEN
 383         select XEN_XENBUS_FRONTEND
 384         default y
 385         help
 386           This driver provides support for Xen paravirtual network
 387           devices exported by a Xen network driver domain (often
 388           domain 0).
 389
 390           The corresponding Linux backend driver is enabled by the
 391           CONFIG_XEN_NETDEV_BACKEND option.
 392
 393           If you are compiling a kernel for use as Xen guest, you
 394           should say Y here. To compile this driver as a module, chose
 395           M here: the module will be called xen-netfront.
 396
 397 config XEN_NETDEV_BACKEND
 398         tristate "Xen backend network device"
 399         depends on XEN_BACKEND
 400         help
 401           This driver allows the kernel to act as a Xen network driver
 402           domain which exports paravirtual network devices to other
 403           Xen domains. These devices can be accessed by any operating
 404           system that implements a compatible front end.
 405
 406           The corresponding Linux frontend driver is enabled by the
 407           CONFIG_XEN_NETDEV_FRONTEND configuration option.
 408
 409           The backend driver presents a standard network device
 410           endpoint for each paravirtual network device to the driver
 411           domain network stack. These can then be bridged or routed
 412           etc in order to provide full network connectivity.
 413
 414           If you are compiling a kernel to run in a Xen network driver
 415           domain (often this is domain 0) you should say Y here. To
 416           compile this driver as a module, chose M here: the module
 417           will be called xen-netback.
 418
 419 config VMXNET3
 420         tristate "VMware VMXNET3 ethernet driver"
 421         depends on PCI && INET
 422         help
 423           This driver supports VMware's vmxnet3 virtual ethernet NIC.
 424           To compile this driver as a module, choose M here: the
 425           module will be called vmxnet3.
 426
 427 config FUJITSU_ES
 428         tristate "FUJITSU Extended Socket Network Device driver"
 429         depends on ACPI
 430         help
 431           This driver provides support for Extended Socket network device
 432           on Extended Partitioning of FUJITSU PRIMEQUEST 2000 E2 series.
 433
 434 source "drivers/net/hyperv/Kconfig"
 435
 436 endif # NETDEVICES