drivers/net/Kconfig

   1 #
   2 # Network device configuration
   3 #
   4
   5 menuconfig NETDEVICES
   6         default y if UML
   7         depends on NET
   8         bool "Network device support"
   9         ---help---
  10           You can say N here if you don't intend to connect your Linux box to
  11           any other computer at all.
  12
  13           You'll have to say Y if your computer contains a network card that
  14           you want to use under Linux. If you are going to run SLIP or PPP over
  15           telephone line or null modem cable you need say Y here. Connecting
  16           two machines with parallel ports using PLIP needs this, as well as
  17           AX.25/KISS for sending Internet traffic over amateur radio links.
  18
  19           See also "The Linux Network Administrator's Guide" by Olaf Kirch and
  20           Terry Dawson. Available at <http://www.tldp.org/guides.html>.
  21
  22           If unsure, say Y.
  23
  24 # All the following symbols are dependent on NETDEVICES - do not repeat
  25 # that for each of the symbols.
  26 if NETDEVICES
  27
  28 config MII
  29         tristate
  30
  31 config NET_CORE
  32         default y
  33         bool "Network core driver support"
  34         ---help---
  35           You can say N here if you do not intend to use any of the
  36           networking core drivers (i.e. VLAN, bridging, bonding, etc.)
  37
  38 if NET_CORE
  39
  40 config BONDING
  41         tristate "Bonding driver support"
  42         depends on INET
  43         depends on IPV6 || IPV6=n
  44         ---help---
  45           Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
  46           Channels together. This is called 'Etherchannel' by Cisco,
  47           'Trunking' by Sun, 802.3ad by the IEEE, and 'Bonding' in Linux.
  48
  49           The driver supports multiple bonding modes to allow for both high
  50           performance and high availability operation.
  51
  52           Refer to <file:Documentation/networking/bonding.txt> for more
  53           information.
  54
  55           To compile this driver as a module, choose M here: the module
  56           will be called bonding.
  57
  58 config DUMMY
  59         tristate "Dummy net driver support"
  60         ---help---
  61           This is essentially a bit-bucket device (i.e. traffic you send to
  62           this device is consigned into oblivion) with a configurable IP
  63           address. It is most commonly used in order to make your currently
  64           inactive SLIP address seem like a real address for local programs.
  65           If you use SLIP or PPP, you might want to say Y here. Since this
  66           thing often comes in handy, the default is Y. It won't enlarge your
  67           kernel either. What a deal. Read about it in the Network
  68           Administrator's Guide, available from
  69           <http://www.tldp.org/docs.html#guide>.
  70
  71           To compile this driver as a module, choose M here: the module
  72           will be called dummy.
  73
  74 config EQUALIZER
  75         tristate "EQL (serial line load balancing) support"
  76         ---help---
  77           If you have two serial connections to some other computer (this
  78           usually requires two modems and two telephone lines) and you use
  79           SLIP (the protocol for sending Internet traffic over telephone
  80           lines) or PPP (a better SLIP) on them, you can make them behave like
  81           one double speed connection using this driver.  Naturally, this has
  82           to be supported at the other end as well, either with a similar EQL
  83           Linux driver or with a Livingston Portmaster 2e.
  84
  85           Say Y if you want this and read
  86           <file:Documentation/networking/eql.txt>.  You may also want to read
  87           section 6.2 of the NET-3-HOWTO, available from
  88           <http://www.tldp.org/docs.html#howto>.
  89
  90           To compile this driver as a module, choose M here: the module
  91           will be called eql.  If unsure, say N.
  92
  93 config NET_FC
  94         bool "Fibre Channel driver support"
  95         depends on SCSI && PCI
  96         help
  97           Fibre Channel is a high speed serial protocol mainly used to connect
  98           large storage devices to the computer; it is compatible with and
  99           intended to replace SCSI.
 100
 101           If you intend to use Fibre Channel, you need to have a Fibre channel
 102           adaptor card in your computer; say Y here and to the driver for your
 103           adaptor below. You also should have said Y to "SCSI support" and
 104           "SCSI generic support".
 105
 106 config IFB
 107         tristate "Intermediate Functional Block support"
 108         depends on NET_CLS_ACT
 109         ---help---
 110           This is an intermediate driver that allows sharing of
 111           resources.
 112           To compile this driver as a module, choose M here: the module
 113           will be called ifb.  If you want to use more than one ifb
 114           device at a time, you need to compile this driver as a module.
 115           Instead of 'ifb', the devices will then be called 'ifb0',
 116           'ifb1' etc.
 117           Look at the iproute2 documentation directory for usage etc
 118
 119 source "drivers/net/team/Kconfig"
 120
 121 config MACVLAN
 122         tristate "MAC-VLAN support"
 123         ---help---
 124           This allows one to create virtual interfaces that map packets to
 125           or from specific MAC addresses to a particular interface.
 126
 127           Macvlan devices can be added using the "ip" command from the
 128           iproute2 package starting with the iproute2-2.6.23 release:
 129
 130           "ip link add link <real dev> [ address MAC ] [ NAME ] type macvlan"
 131
 132           To compile this driver as a module, choose M here: the module
 133           will be called macvlan.
 134
 135 config MACVTAP
 136         tristate "MAC-VLAN based tap driver"
 137         depends on MACVLAN
 138         help
 139           This adds a specialized tap character device driver that is based
 140           on the MAC-VLAN network interface, called macvtap. A macvtap device
 141           can be added in the same way as a macvlan device, using 'type
 142           macvlan', and then be accessed through the tap user space interface.
 143
 144           To compile this driver as a module, choose M here: the module
 145           will be called macvtap.
 146
 147 config VXLAN
 148        tristate "Virtual eXtensible Local Area Network (VXLAN)"
 149        depends on INET
 150        select NET_IP_TUNNEL
 151        ---help---
 152           This allows one to create vxlan virtual interfaces that provide
 153           Layer 2 Networks over Layer 3 Networks. VXLAN is often used
 154           to tunnel virtual network infrastructure in virtualized environments.
 155           For more information see:
 156             http://tools.ietf.org/html/draft-mahalingam-dutt-dcops-vxlan-02
 157
 158           To compile this driver as a module, choose M here: the module
 159           will be called vxlan.
 160
 161 config NETCONSOLE
 162         tristate "Network console logging support"
 163         ---help---
 164         If you want to log kernel messages over the network, enable this.
 165         See <file:Documentation/networking/netconsole.txt> for details.
 166
 167 config NETCONSOLE_DYNAMIC
 168         bool "Dynamic reconfiguration of logging targets"
 169         depends on NETCONSOLE && SYSFS && CONFIGFS_FS && \
 170                         !(NETCONSOLE=y && CONFIGFS_FS=m)
 171         help
 172           This option enables the ability to dynamically reconfigure target
 173           parameters (interface, IP addresses, port numbers, MAC addresses)
 174           at runtime through a userspace interface exported using configfs.
 175           See <file:Documentation/networking/netconsole.txt> for details.
 176
 177 config NETPOLL
 178         def_bool NETCONSOLE
 179
 180 config NETPOLL_TRAP
 181         bool "Netpoll traffic trapping"
 182         default n
 183         depends on NETPOLL
 184
 185 config NET_POLL_CONTROLLER
 186         def_bool NETPOLL
 187
 188 config NTB_NETDEV
 189         tristate "Virtual Ethernet over NTB"
 190         depends on NTB
 191
 192 config RIONET
 193         tristate "RapidIO Ethernet over messaging driver support"
 194         depends on RAPIDIO
 195
 196 config RIONET_TX_SIZE
 197         int "Number of outbound queue entries"
 198         depends on RIONET
 199         default "128"
 200
 201 config RIONET_RX_SIZE
 202         int "Number of inbound queue entries"
 203         depends on RIONET
 204         default "128"
 205
 206 config TUN
 207         tristate "Universal TUN/TAP device driver support"
 208         select CRC32
 209         ---help---
 210           TUN/TAP provides packet reception and transmission for user space
 211           programs.  It can be viewed as a simple Point-to-Point or Ethernet
 212           device, which instead of receiving packets from a physical media,
 213           receives them from user space program and instead of sending packets
 214           via physical media writes them to the user space program.
 215
 216           When a program opens /dev/net/tun, driver creates and registers
 217           corresponding net device tunX or tapX.  After a program closed above
 218           devices, driver will automatically delete tunXX or tapXX device and
 219           all routes corresponding to it.
 220
 221           Please read <file:Documentation/networking/tuntap.txt> for more
 222           information.
 223
 224           To compile this driver as a module, choose M here: the module
 225           will be called tun.
 226
 227           If you don't know what to use this for, you don't need it.
 228
 229 config VETH
 230         tristate "Virtual ethernet pair device"
 231         ---help---
 232           This device is a local ethernet tunnel. Devices are created in pairs.
 233           When one end receives the packet it appears on its pair and vice
 234           versa.
 235
 236 config VIRTIO_NET
 237         tristate "Virtio network driver"
 238         depends on VIRTIO
 239         ---help---
 240           This is the virtual network driver for virtio.  It can be used with
 241           lguest or QEMU based VMMs (like KVM or Xen).  Say Y or M.
 242
 243 config NLMON
 244         tristate "Virtual netlink monitoring device"
 245         ---help---
 246           This option enables a monitoring net device for netlink skbs. The
 247           purpose of this is to analyze netlink messages with packet sockets.
 248           Thus applications like tcpdump will be able to see local netlink
 249           messages if they tap into the netlink device, record pcaps for further
 250           diagnostics, etc. This is mostly intended for developers or support
 251           to debug netlink issues. If unsure, say N.
 252
 253 endif # NET_CORE
 254
 255 config SUNGEM_PHY
 256         tristate
 257
 258 source "drivers/net/arcnet/Kconfig"
 259
 260 source "drivers/atm/Kconfig"
 261
 262 source "drivers/net/caif/Kconfig"
 263
 264 source "drivers/net/dsa/Kconfig"
 265
 266 source "drivers/net/ethernet/Kconfig"
 267
 268 source "drivers/net/fddi/Kconfig"
 269
 270 source "drivers/net/hippi/Kconfig"
 271
 272 config NET_SB1000
 273         tristate "General Instruments Surfboard 1000"
 274         depends on PNP
 275         ---help---
 276           This is a driver for the General Instrument (also known as
 277           NextLevel) SURFboard 1000 internal
 278           cable modem. This is an ISA card which is used by a number of cable
 279           TV companies to provide cable modem access. It's a one-way
 280           downstream-only cable modem, meaning that your upstream net link is
 281           provided by your regular phone modem.
 282
 283           At present this driver only compiles as a module, so say M here if
 284           you have this card. The module will be called sb1000. Then read
 285           <file:Documentation/networking/README.sb1000> for information on how
 286           to use this module, as it needs special ppp scripts for establishing
 287           a connection. Further documentation and the necessary scripts can be
 288           found at:
 289
 290           <http://www.jacksonville.net/~fventuri/>
 291           <http://home.adelphia.net/~siglercm/sb1000.html>
 292           <http://linuxpower.cx/~cable/>
 293
 294           If you don't have this card, of course say N.
 295
 296 source "drivers/net/phy/Kconfig"
 297
 298 source "drivers/net/plip/Kconfig"
 299
 300 source "drivers/net/ppp/Kconfig"
 301
 302 source "drivers/net/slip/Kconfig"
 303
 304 source "drivers/s390/net/Kconfig"
 305
 306 source "drivers/net/usb/Kconfig"
 307
 308 source "drivers/net/wireless/Kconfig"
 309
 310 source "drivers/net/wimax/Kconfig"
 311
 312 source "drivers/net/wan/Kconfig"
 313
 314 source "drivers/net/ieee802154/Kconfig"
 315
 316 config XEN_NETDEV_FRONTEND
 317         tristate "Xen network device frontend driver"
 318         depends on XEN
 319         select XEN_XENBUS_FRONTEND
 320         default y
 321         help
 322           This driver provides support for Xen paravirtual network
 323           devices exported by a Xen network driver domain (often
 324           domain 0).
 325
 326           The corresponding Linux backend driver is enabled by the
 327           CONFIG_XEN_NETDEV_BACKEND option.
 328
 329           If you are compiling a kernel for use as Xen guest, you
 330           should say Y here. To compile this driver as a module, chose
 331           M here: the module will be called xen-netfront.
 332
 333 config XEN_NETDEV_BACKEND
 334         tristate "Xen backend network device"
 335         depends on XEN_BACKEND
 336         help
 337           This driver allows the kernel to act as a Xen network driver
 338           domain which exports paravirtual network devices to other
 339           Xen domains. These devices can be accessed by any operating
 340           system that implements a compatible front end.
 341
 342           The corresponding Linux frontend driver is enabled by the
 343           CONFIG_XEN_NETDEV_FRONTEND configuration option.
 344
 345           The backend driver presents a standard network device
 346           endpoint for each paravirtual network device to the driver
 347           domain network stack. These can then be bridged or routed
 348           etc in order to provide full network connectivity.
 349
 350           If you are compiling a kernel to run in a Xen network driver
 351           domain (often this is domain 0) you should say Y here. To
 352           compile this driver as a module, chose M here: the module
 353           will be called xen-netback.
 354
 355 config VMXNET3
 356         tristate "VMware VMXNET3 ethernet driver"
 357         depends on PCI && INET
 358         help
 359           This driver supports VMware's vmxnet3 virtual ethernet NIC.
 360           To compile this driver as a module, choose M here: the
 361           module will be called vmxnet3.
 362
 363 source "drivers/net/hyperv/Kconfig"
 364
 365 endif # NETDEVICES