drivers/net/can/Kconfig

   1 menu "CAN Device Drivers"
   2
   3 config CAN_VCAN
   4         tristate "Virtual Local CAN Interface (vcan)"
   5         ---help---
   6           Similar to the network loopback devices, vcan offers a
   7           virtual local CAN interface.
   8
   9           This driver can also be built as a module.  If so, the module
  10           will be called vcan.
  11
  12 config CAN_SLCAN
  13         tristate "Serial / USB serial CAN Adaptors (slcan)"
  14         depends on TTY
  15         ---help---
  16           CAN driver for several 'low cost' CAN interfaces that are attached
  17           via serial lines or via USB-to-serial adapters using the LAWICEL
  18           ASCII protocol. The driver implements the tty linediscipline N_SLCAN.
  19
  20           As only the sending and receiving of CAN frames is implemented, this
  21           driver should work with the (serial/USB) CAN hardware from:
  22           www.canusb.com / www.can232.com / www.mictronics.de / www.canhack.de
  23
  24           Userspace tools to attach the SLCAN line discipline (slcan_attach,
  25           slcand) can be found in the can-utils at the SocketCAN SVN, see
  26           http://developer.berlios.de/projects/socketcan for details.
  27
  28           The slcan driver supports up to 10 CAN netdevices by default which
  29           can be changed by the 'maxdev=xx' module option. This driver can
  30           also be built as a module. If so, the module will be called slcan.
  31
  32 config CAN_DEV
  33         tristate "Platform CAN drivers with Netlink support"
  34         default y
  35         ---help---
  36           Enables the common framework for platform CAN drivers with Netlink
  37           support. This is the standard library for CAN drivers.
  38           If unsure, say Y.
  39
  40 if CAN_DEV
  41
  42 config CAN_CALC_BITTIMING
  43         bool "CAN bit-timing calculation"
  44         default y
  45         ---help---
  46           If enabled, CAN bit-timing parameters will be calculated for the
  47           bit-rate specified via Netlink argument "bitrate" when the device
  48           get started. This works fine for the most common CAN controllers
  49           with standard bit-rates but may fail for exotic bit-rates or CAN
  50           source clock frequencies. Disabling saves some space, but then the
  51           bit-timing parameters must be specified directly using the Netlink
  52           arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw".
  53           If unsure, say Y.
  54
  55 config CAN_LEDS
  56         bool "Enable LED triggers for Netlink based drivers"
  57         depends on LEDS_CLASS
  58         select LEDS_TRIGGERS
  59         ---help---
  60           This option adds two LED triggers for packet receive and transmit
  61           events on each supported CAN device.
  62
  63           Say Y here if you are working on a system with led-class supported
  64           LEDs and you want to use them as canbus activity indicators.
  65
  66 config CAN_AT91
  67         tristate "Atmel AT91 onchip CAN controller"
  68         depends on (ARCH_AT91 || COMPILE_TEST) && HAS_IOMEM
  69         ---help---
  70           This is a driver for the SoC CAN controller in Atmel's AT91SAM9263
  71           and AT91SAM9X5 processors.
  72
  73 config CAN_TI_HECC
  74         depends on ARM
  75         tristate "TI High End CAN Controller"
  76         ---help---
  77           Driver for TI HECC (High End CAN Controller) module found on many
  78           TI devices. The device specifications are available from www.ti.com
  79
  80 config CAN_BFIN
  81         depends on BF534 || BF536 || BF537 || BF538 || BF539 || BF54x
  82         tristate "Analog Devices Blackfin on-chip CAN"
  83         ---help---
  84           Driver for the Analog Devices Blackfin on-chip CAN controllers
  85
  86           To compile this driver as a module, choose M here: the
  87           module will be called bfin_can.
  88
  89 config CAN_JANZ_ICAN3
  90         tristate "Janz VMOD-ICAN3 Intelligent CAN controller"
  91         depends on MFD_JANZ_CMODIO
  92         ---help---
  93           Driver for Janz VMOD-ICAN3 Intelligent CAN controller module, which
  94           connects to a MODULbus carrier board.
  95
  96           This driver can also be built as a module. If so, the module will be
  97           called janz-ican3.ko.
  98
  99 config CAN_FLEXCAN
 100         tristate "Support for Freescale FLEXCAN based chips"
 101         depends on ARM || PPC
 102         ---help---
 103           Say Y here if you want to support for Freescale FlexCAN.
 104
 105 config PCH_CAN
 106         tristate "Intel EG20T PCH CAN controller"
 107         depends on PCI && (X86_32 || COMPILE_TEST)
 108         ---help---
 109           This driver is for PCH CAN of Topcliff (Intel EG20T PCH) which
 110           is an IOH for x86 embedded processor (Intel Atom E6xx series).
 111           This driver can access CAN bus.
 112
 113 config CAN_GRCAN
 114         tristate "Aeroflex Gaisler GRCAN and GRHCAN CAN devices"
 115         depends on OF && HAS_DMA
 116         ---help---
 117           Say Y here if you want to use Aeroflex Gaisler GRCAN or GRHCAN.
 118           Note that the driver supports little endian, even though little
 119           endian syntheses of the cores would need some modifications on
 120           the hardware level to work.
 121
 122 config CAN_RCAR
 123         tristate "Renesas R-Car CAN controller"
 124         depends on ARM
 125         ---help---
 126           Say Y here if you want to use CAN controller found on Renesas R-Car
 127           SoCs.
 128
 129           To compile this driver as a module, choose M here: the module will
 130           be called rcar_can.
 131
 132 config CAN_SUN4I
 133         tristate "Allwinner A10 CAN controller"
 134         depends on MACH_SUN4I || MACH_SUN7I || COMPILE_TEST
 135         ---help---
 136           Say Y here if you want to use CAN controller found on Allwinner
 137           A10/A20 SoCs.
 138
 139           To compile this driver as a module, choose M here: the module will
 140           be called sun4i_can.
 141
 142 config CAN_XILINXCAN
 143         tristate "Xilinx CAN"
 144         depends on ARCH_ZYNQ || ARM64 || MICROBLAZE || COMPILE_TEST
 145         depends on COMMON_CLK && HAS_IOMEM
 146         ---help---
 147           Xilinx CAN driver. This driver supports both soft AXI CAN IP and
 148           Zynq CANPS IP.
 149
 150 source "drivers/net/can/mscan/Kconfig"
 151
 152 source "drivers/net/can/sja1000/Kconfig"
 153
 154 source "drivers/net/can/c_can/Kconfig"
 155
 156 source "drivers/net/can/m_can/Kconfig"
 157
 158 source "drivers/net/can/cc770/Kconfig"
 159
 160 source "drivers/net/can/spi/Kconfig"
 161
 162 source "drivers/net/can/usb/Kconfig"
 163
 164 source "drivers/net/can/softing/Kconfig"
 165
 166 endif
 167
 168 config CAN_DEBUG_DEVICES
 169         bool "CAN devices debugging messages"
 170         ---help---
 171           Say Y here if you want the CAN device drivers to produce a bunch of
 172           debug messages to the system log.  Select this if you are having
 173           a problem with CAN support and want to see more of what is going
 174           on.
 175
 176 endmenu