drivers/net/ethernet/broadcom/genet/bcmmii.c

   1 /*
   2  * Broadcom GENET MDIO routines
   3  *
   4  * Copyright (c) 2014 Broadcom Corporation
   5  *
   6  * This program is free software; you can redistribute it and/or modify
   7  * it under the terms of the GNU General Public License version 2 as
   8  * published by the Free Software Foundation.
   9  */
  10
  11
  12 #include <linux/types.h>
  13 #include <linux/delay.h>
  14 #include <linux/wait.h>
  15 #include <linux/mii.h>
  16 #include <linux/ethtool.h>
  17 #include <linux/bitops.h>
  18 #include <linux/netdevice.h>
  19 #include <linux/platform_device.h>
  20 #include <linux/phy.h>
  21 #include <linux/phy_fixed.h>
  22 #include <linux/brcmphy.h>
  23 #include <linux/of.h>
  24 #include <linux/of_net.h>
  25 #include <linux/of_mdio.h>
  26 #include <linux/platform_data/bcmgenet.h>
  27
  28 #include "bcmgenet.h"
  29
  30 /* read a value from the MII */
  31 static int bcmgenet_mii_read(struct mii_bus *bus, int phy_id, int location)
  32 {
  33         int ret;
  34         struct net_device *dev = bus->priv;
  35         struct bcmgenet_priv *priv = netdev_priv(dev);
  36         u32 reg;
  37
  38         bcmgenet_umac_writel(priv, (MDIO_RD | (phy_id << MDIO_PMD_SHIFT) |
  39                              (location << MDIO_REG_SHIFT)), UMAC_MDIO_CMD);
  40         /* Start MDIO transaction*/
  41         reg = bcmgenet_umac_readl(priv, UMAC_MDIO_CMD);
  42         reg |= MDIO_START_BUSY;
  43         bcmgenet_umac_writel(priv, reg, UMAC_MDIO_CMD);
  44         wait_event_timeout(priv->wq,
  45                            !(bcmgenet_umac_readl(priv, UMAC_MDIO_CMD)
  46                            & MDIO_START_BUSY),
  47                            HZ / 100);
  48         ret = bcmgenet_umac_readl(priv, UMAC_MDIO_CMD);
  49
  50         if (ret & MDIO_READ_FAIL)
  51                 return -EIO;
  52
  53         return ret & 0xffff;
  54 }
  55
  56 /* write a value to the MII */
  57 static int bcmgenet_mii_write(struct mii_bus *bus, int phy_id,
  58                               int location, u16 val)
  59 {
  60         struct net_device *dev = bus->priv;
  61         struct bcmgenet_priv *priv = netdev_priv(dev);
  62         u32 reg;
  63
  64         bcmgenet_umac_writel(priv, (MDIO_WR | (phy_id << MDIO_PMD_SHIFT) |
  65                              (location << MDIO_REG_SHIFT) | (0xffff & val)),
  66                              UMAC_MDIO_CMD);
  67         reg = bcmgenet_umac_readl(priv, UMAC_MDIO_CMD);
  68         reg |= MDIO_START_BUSY;
  69         bcmgenet_umac_writel(priv, reg, UMAC_MDIO_CMD);
  70         wait_event_timeout(priv->wq,
  71                            !(bcmgenet_umac_readl(priv, UMAC_MDIO_CMD) &
  72                            MDIO_START_BUSY),
  73                            HZ / 100);
  74
  75         return 0;
  76 }
  77
  78 /* setup netdev link state when PHY link status change and
  79  * update UMAC and RGMII block when link up
  80  */
  81 void bcmgenet_mii_setup(struct net_device *dev)
  82 {
  83         struct bcmgenet_priv *priv = netdev_priv(dev);
  84         struct phy_device *phydev = priv->phydev;
  85         u32 reg, cmd_bits = 0;
  86         bool status_changed = false;
  87
  88         if (priv->old_link != phydev->link) {
  89                 status_changed = true;
  90                 priv->old_link = phydev->link;
  91         }
  92
  93         if (phydev->link) {
  94                 /* check speed/duplex/pause changes */
  95                 if (priv->old_speed != phydev->speed) {
  96                         status_changed = true;
  97                         priv->old_speed = phydev->speed;
  98                 }
  99
 100                 if (priv->old_duplex != phydev->duplex) {
 101                         status_changed = true;
 102                         priv->old_duplex = phydev->duplex;
 103                 }
 104
 105                 if (priv->old_pause != phydev->pause) {
 106                         status_changed = true;
 107                         priv->old_pause = phydev->pause;
 108                 }
 109
 110                 /* done if nothing has changed */
 111                 if (!status_changed)
 112                         return;
 113
 114                 /* speed */
 115                 if (phydev->speed == SPEED_1000)
 116                         cmd_bits = UMAC_SPEED_1000;
 117                 else if (phydev->speed == SPEED_100)
 118                         cmd_bits = UMAC_SPEED_100;
 119                 else
 120                         cmd_bits = UMAC_SPEED_10;
 121                 cmd_bits <<= CMD_SPEED_SHIFT;
 122
 123                 /* duplex */
 124                 if (phydev->duplex != DUPLEX_FULL)
 125                         cmd_bits |= CMD_HD_EN;
 126
 127                 /* pause capability */
 128                 if (!phydev->pause)
 129                         cmd_bits |= CMD_RX_PAUSE_IGNORE | CMD_TX_PAUSE_IGNORE;
 130
 131                 /*
 132                  * Program UMAC and RGMII block based on established
 133                  * link speed, duplex, and pause. The speed set in
 134                  * umac->cmd tell RGMII block which clock to use for
 135                  * transmit -- 25MHz(100Mbps) or 125MHz(1Gbps).
 136                  * Receive clock is provided by the PHY.
 137                  */
 138                 reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
 139                 reg &= ~OOB_DISABLE;
 140                 reg |= RGMII_LINK;
 141                 bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
 142
 143                 reg = bcmgenet_umac_readl(priv, UMAC_CMD);
 144                 reg &= ~((CMD_SPEED_MASK << CMD_SPEED_SHIFT) |
 145                                CMD_HD_EN |
 146                                CMD_RX_PAUSE_IGNORE | CMD_TX_PAUSE_IGNORE);
 147                 reg |= cmd_bits;
 148                 bcmgenet_umac_writel(priv, reg, UMAC_CMD);
 149         } else {
 150                 /* done if nothing has changed */
 151                 if (!status_changed)
 152                         return;
 153
 154                 /* needed for MoCA fixed PHY to reflect correct link status */
 155                 netif_carrier_off(dev);
 156         }
 157
 158         phy_print_status(phydev);
 159 }
 160
 161 void bcmgenet_mii_reset(struct net_device *dev)
 162 {
 163         struct bcmgenet_priv *priv = netdev_priv(dev);
 164
 165         if (priv->phydev) {
 166                 phy_init_hw(priv->phydev);
 167                 phy_start_aneg(priv->phydev);
 168         }
 169 }
 170
 171 void bcmgenet_phy_power_set(struct net_device *dev, bool enable)
 172 {
 173         struct bcmgenet_priv *priv = netdev_priv(dev);
 174         u32 reg = 0;
 175
 176         /* EXT_GPHY_CTRL is only valid for GENETv4 and onward */
 177         if (!GENET_IS_V4(priv))
 178                 return;
 179
 180         reg = bcmgenet_ext_readl(priv, EXT_GPHY_CTRL);
 181         if (enable) {
 182                 reg &= ~EXT_CK25_DIS;
 183                 bcmgenet_ext_writel(priv, reg, EXT_GPHY_CTRL);
 184                 mdelay(1);
 185
 186                 reg &= ~(EXT_CFG_IDDQ_BIAS | EXT_CFG_PWR_DOWN);
 187                 reg |= EXT_GPHY_RESET;
 188                 bcmgenet_ext_writel(priv, reg, EXT_GPHY_CTRL);
 189                 mdelay(1);
 190
 191                 reg &= ~EXT_GPHY_RESET;
 192         } else {
 193                 reg |= EXT_CFG_IDDQ_BIAS | EXT_CFG_PWR_DOWN | EXT_GPHY_RESET;
 194                 bcmgenet_ext_writel(priv, reg, EXT_GPHY_CTRL);
 195                 mdelay(1);
 196                 reg |= EXT_CK25_DIS;
 197         }
 198         bcmgenet_ext_writel(priv, reg, EXT_GPHY_CTRL);
 199         udelay(60);
 200 }
 201
 202 static void bcmgenet_internal_phy_setup(struct net_device *dev)
 203 {
 204         struct bcmgenet_priv *priv = netdev_priv(dev);
 205         u32 reg;
 206
 207         /* Power up PHY */
 208         bcmgenet_phy_power_set(dev, true);
 209         /* enable APD */
 210         reg = bcmgenet_ext_readl(priv, EXT_EXT_PWR_MGMT);
 211         reg |= EXT_PWR_DN_EN_LD;
 212         bcmgenet_ext_writel(priv, reg, EXT_EXT_PWR_MGMT);
 213         bcmgenet_mii_reset(dev);
 214 }
 215
 216 static void bcmgenet_moca_phy_setup(struct bcmgenet_priv *priv)
 217 {
 218         u32 reg;
 219
 220         /* Speed settings are set in bcmgenet_mii_setup() */
 221         reg = bcmgenet_sys_readl(priv, SYS_PORT_CTRL);
 222         reg |= LED_ACT_SOURCE_MAC;
 223         bcmgenet_sys_writel(priv, reg, SYS_PORT_CTRL);
 224 }
 225
 226 int bcmgenet_mii_config(struct net_device *dev, bool init)
 227 {
 228         struct bcmgenet_priv *priv = netdev_priv(dev);
 229         struct phy_device *phydev = priv->phydev;
 230         struct device *kdev = &priv->pdev->dev;
 231         const char *phy_name = NULL;
 232         u32 id_mode_dis = 0;
 233         u32 port_ctrl;
 234         u32 reg;
 235
 236         priv->ext_phy = !phy_is_internal(priv->phydev) &&
 237                         (priv->phy_interface != PHY_INTERFACE_MODE_MOCA);
 238
 239         if (phy_is_internal(priv->phydev))
 240                 priv->phy_interface = PHY_INTERFACE_MODE_NA;
 241
 242         switch (priv->phy_interface) {
 243         case PHY_INTERFACE_MODE_NA:
 244         case PHY_INTERFACE_MODE_MOCA:
 245                 /* Irrespective of the actually configured PHY speed (100 or
 246                  * 1000) GENETv4 only has an internal GPHY so we will just end
 247                  * up masking the Gigabit features from what we support, not
 248                  * switching to the EPHY
 249                  */
 250                 if (GENET_IS_V4(priv))
 251                         port_ctrl = PORT_MODE_INT_GPHY;
 252                 else
 253                         port_ctrl = PORT_MODE_INT_EPHY;
 254
 255                 bcmgenet_sys_writel(priv, port_ctrl, SYS_PORT_CTRL);
 256
 257                 if (phy_is_internal(priv->phydev)) {
 258                         phy_name = "internal PHY";
 259                         bcmgenet_internal_phy_setup(dev);
 260                 } else if (priv->phy_interface == PHY_INTERFACE_MODE_MOCA) {
 261                         phy_name = "MoCA";
 262                         bcmgenet_moca_phy_setup(priv);
 263                 }
 264                 break;
 265
 266         case PHY_INTERFACE_MODE_MII:
 267                 phy_name = "external MII";
 268                 phydev->supported &= PHY_BASIC_FEATURES;
 269                 bcmgenet_sys_writel(priv,
 270                                     PORT_MODE_EXT_EPHY, SYS_PORT_CTRL);
 271                 break;
 272
 273         case PHY_INTERFACE_MODE_REVMII:
 274                 phy_name = "external RvMII";
 275                 /* of_mdiobus_register took care of reading the 'max-speed'
 276                  * PHY property for us, effectively limiting the PHY supported
 277                  * capabilities, use that knowledge to also configure the
 278                  * Reverse MII interface correctly.
 279                  */
 280                 if ((priv->phydev->supported & PHY_BASIC_FEATURES) ==
 281                                 PHY_BASIC_FEATURES)
 282                         port_ctrl = PORT_MODE_EXT_RVMII_25;
 283                 else
 284                         port_ctrl = PORT_MODE_EXT_RVMII_50;
 285                 bcmgenet_sys_writel(priv, port_ctrl, SYS_PORT_CTRL);
 286                 break;
 287
 288         case PHY_INTERFACE_MODE_RGMII:
 289                 /* RGMII_NO_ID: TXC transitions at the same time as TXD
 290                  *              (requires PCB or receiver-side delay)
 291                  * RGMII:       Add 2ns delay on TXC (90 degree shift)
 292                  *
 293                  * ID is implicitly disabled for 100Mbps (RG)MII operation.
 294                  */
 295                 id_mode_dis = BIT(16);
 296                 /* fall through */
 297         case PHY_INTERFACE_MODE_RGMII_TXID:
 298                 if (id_mode_dis)
 299                         phy_name = "external RGMII (no delay)";
 300                 else
 301                         phy_name = "external RGMII (TX delay)";
 302                 reg = bcmgenet_ext_readl(priv, EXT_RGMII_OOB_CTRL);
 303                 reg |= RGMII_MODE_EN | id_mode_dis;
 304                 bcmgenet_ext_writel(priv, reg, EXT_RGMII_OOB_CTRL);
 305                 bcmgenet_sys_writel(priv,
 306                                     PORT_MODE_EXT_GPHY, SYS_PORT_CTRL);
 307                 break;
 308         default:
 309                 dev_err(kdev, "unknown phy mode: %d\n", priv->phy_interface);
 310                 return -EINVAL;
 311         }
 312
 313         if (init)
 314                 dev_info(kdev, "configuring instance for %s\n", phy_name);
 315
 316         return 0;
 317 }
 318
 319 static int bcmgenet_mii_probe(struct net_device *dev)
 320 {
 321         struct bcmgenet_priv *priv = netdev_priv(dev);
 322         struct device_node *dn = priv->pdev->dev.of_node;
 323         struct phy_device *phydev;
 324         u32 phy_flags;
 325         int ret;
 326
 327         /* Communicate the integrated PHY revision */
 328         phy_flags = priv->gphy_rev;
 329
 330         /* Initialize link state variables that bcmgenet_mii_setup() uses */
 331         priv->old_link = -1;
 332         priv->old_speed = -1;
 333         priv->old_duplex = -1;
 334         priv->old_pause = -1;
 335
 336         if (dn) {
 337                 if (priv->phydev) {
 338                         pr_info("PHY already attached\n");
 339                         return 0;
 340                 }
 341
 342                 /* In the case of a fixed PHY, the DT node associated
 343                  * to the PHY is the Ethernet MAC DT node.
 344                  */
 345                 if (!priv->phy_dn && of_phy_is_fixed_link(dn)) {
 346                         ret = of_phy_register_fixed_link(dn);
 347                         if (ret)
 348                                 return ret;
 349
 350                         priv->phy_dn = of_node_get(dn);
 351                 }
 352
 353                 phydev = of_phy_connect(dev, priv->phy_dn, bcmgenet_mii_setup,
 354                                         phy_flags, priv->phy_interface);
 355                 if (!phydev) {
 356                         pr_err("could not attach to PHY\n");
 357                         return -ENODEV;
 358                 }
 359         } else {
 360                 phydev = priv->phydev;
 361                 phydev->dev_flags = phy_flags;
 362
 363                 ret = phy_connect_direct(dev, phydev, bcmgenet_mii_setup,
 364                                          priv->phy_interface);
 365                 if (ret) {
 366                         pr_err("could not attach to PHY\n");
 367                         return -ENODEV;
 368                 }
 369         }
 370
 371         priv->phydev = phydev;
 372
 373         /* Configure port multiplexer based on what the probed PHY device since
 374          * reading the 'max-speed' property determines the maximum supported
 375          * PHY speed which is needed for bcmgenet_mii_config() to configure
 376          * things appropriately.
 377          */
 378         ret = bcmgenet_mii_config(dev, true);
 379         if (ret) {
 380                 phy_disconnect(priv->phydev);
 381                 return ret;
 382         }
 383
 384         phydev->advertising = phydev->supported;
 385
 386         /* The internal PHY has its link interrupts routed to the
 387          * Ethernet MAC ISRs
 388          */
 389         if (phy_is_internal(priv->phydev))
 390                 priv->mii_bus->irq[phydev->addr] = PHY_IGNORE_INTERRUPT;
 391         else
 392                 priv->mii_bus->irq[phydev->addr] = PHY_POLL;
 393
 394         pr_info("attached PHY at address %d [%s]\n",
 395                 phydev->addr, phydev->drv->name);
 396
 397         return 0;
 398 }
 399
 400 static int bcmgenet_mii_alloc(struct bcmgenet_priv *priv)
 401 {
 402         struct mii_bus *bus;
 403
 404         if (priv->mii_bus)
 405                 return 0;
 406
 407         priv->mii_bus = mdiobus_alloc();
 408         if (!priv->mii_bus) {
 409                 pr_err("failed to allocate\n");
 410                 return -ENOMEM;
 411         }
 412
 413         bus = priv->mii_bus;
 414         bus->priv = priv->dev;
 415         bus->name = "bcmgenet MII bus";
 416         bus->parent = &priv->pdev->dev;
 417         bus->read = bcmgenet_mii_read;
 418         bus->write = bcmgenet_mii_write;
 419         snprintf(bus->id, MII_BUS_ID_SIZE, "%s-%d",
 420                  priv->pdev->name, priv->pdev->id);
 421
 422         bus->irq = kcalloc(PHY_MAX_ADDR, sizeof(int), GFP_KERNEL);
 423         if (!bus->irq) {
 424                 mdiobus_free(priv->mii_bus);
 425                 return -ENOMEM;
 426         }
 427
 428         return 0;
 429 }
 430
 431 static int bcmgenet_mii_of_init(struct bcmgenet_priv *priv)
 432 {
 433         struct device_node *dn = priv->pdev->dev.of_node;
 434         struct device *kdev = &priv->pdev->dev;
 435         struct device_node *mdio_dn;
 436         char *compat;
 437         int ret;
 438
 439         compat = kasprintf(GFP_KERNEL, "brcm,genet-mdio-v%d", priv->version);
 440         if (!compat)
 441                 return -ENOMEM;
 442
 443         mdio_dn = of_find_compatible_node(dn, NULL, compat);
 444         kfree(compat);
 445         if (!mdio_dn) {
 446                 dev_err(kdev, "unable to find MDIO bus node\n");
 447                 return -ENODEV;
 448         }
 449
 450         ret = of_mdiobus_register(priv->mii_bus, mdio_dn);
 451         if (ret) {
 452                 dev_err(kdev, "failed to register MDIO bus\n");
 453                 return ret;
 454         }
 455
 456         /* Fetch the PHY phandle */
 457         priv->phy_dn = of_parse_phandle(dn, "phy-handle", 0);
 458
 459         /* Get the link mode */
 460         priv->phy_interface = of_get_phy_mode(dn);
 461
 462         return 0;
 463 }
 464
 465 static int bcmgenet_mii_pd_init(struct bcmgenet_priv *priv)
 466 {
 467         struct device *kdev = &priv->pdev->dev;
 468         struct bcmgenet_platform_data *pd = kdev->platform_data;
 469         struct mii_bus *mdio = priv->mii_bus;
 470         struct phy_device *phydev;
 471         int ret;
 472
 473         if (pd->phy_interface != PHY_INTERFACE_MODE_MOCA && pd->mdio_enabled) {
 474                 /*
 475                  * Internal or external PHY with MDIO access
 476                  */
 477                 if (pd->phy_address >= 0 && pd->phy_address < PHY_MAX_ADDR)
 478                         mdio->phy_mask = ~(1 << pd->phy_address);
 479                 else
 480                         mdio->phy_mask = 0;
 481
 482                 ret = mdiobus_register(mdio);
 483                 if (ret) {
 484                         dev_err(kdev, "failed to register MDIO bus\n");
 485                         return ret;
 486                 }
 487
 488                 if (pd->phy_address >= 0 && pd->phy_address < PHY_MAX_ADDR)
 489                         phydev = mdio->phy_map[pd->phy_address];
 490                 else
 491                         phydev = phy_find_first(mdio);
 492
 493                 if (!phydev) {
 494                         dev_err(kdev, "failed to register PHY device\n");
 495                         mdiobus_unregister(mdio);
 496                         return -ENODEV;
 497                 }
 498         } else {
 499                 /*
 500                  * MoCA port or no MDIO access.
 501                  * Use fixed PHY to represent the link layer.
 502                  */
 503                 struct fixed_phy_status fphy_status = {
 504                         .link = 1,
 505                         .speed = pd->phy_speed,
 506                         .duplex = pd->phy_duplex,
 507                         .pause = 0,
 508                         .asym_pause = 0,
 509                 };
 510
 511                 phydev = fixed_phy_register(PHY_POLL, &fphy_status, NULL);
 512                 if (!phydev || IS_ERR(phydev)) {
 513                         dev_err(kdev, "failed to register fixed PHY device\n");
 514                         return -ENODEV;
 515                 }
 516         }
 517
 518         priv->phydev = phydev;
 519         priv->phy_interface = pd->phy_interface;
 520
 521         return 0;
 522 }
 523
 524 static int bcmgenet_mii_bus_init(struct bcmgenet_priv *priv)
 525 {
 526         struct device_node *dn = priv->pdev->dev.of_node;
 527
 528         if (dn)
 529                 return bcmgenet_mii_of_init(priv);
 530         else
 531                 return bcmgenet_mii_pd_init(priv);
 532 }
 533
 534 int bcmgenet_mii_init(struct net_device *dev)
 535 {
 536         struct bcmgenet_priv *priv = netdev_priv(dev);
 537         int ret;
 538
 539         ret = bcmgenet_mii_alloc(priv);
 540         if (ret)
 541                 return ret;
 542
 543         ret = bcmgenet_mii_bus_init(priv);
 544         if (ret)
 545                 goto out_free;
 546
 547         ret = bcmgenet_mii_probe(dev);
 548         if (ret)
 549                 goto out;
 550
 551         return 0;
 552
 553 out:
 554         of_node_put(priv->phy_dn);
 555         mdiobus_unregister(priv->mii_bus);
 556 out_free:
 557         kfree(priv->mii_bus->irq);
 558         mdiobus_free(priv->mii_bus);
 559         return ret;
 560 }
 561
 562 void bcmgenet_mii_exit(struct net_device *dev)
 563 {
 564         struct bcmgenet_priv *priv = netdev_priv(dev);
 565
 566         of_node_put(priv->phy_dn);
 567         mdiobus_unregister(priv->mii_bus);
 568         kfree(priv->mii_bus->irq);
 569         mdiobus_free(priv->mii_bus);
 570 }