drivers/net/ethernet/freescale/Kconfig

   1 #
   2 # Freescale device configuration
   3 #
   4
   5 config NET_VENDOR_FREESCALE
   6         bool "Freescale devices"
   7         default y
   8         depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \
   9                    M523x || M527x || M5272 || M528x || M520x || M532x || \
  10                    ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM)
  11         ---help---
  12           If you have a network (Ethernet) card belonging to this class, say Y
  13           and read the Ethernet-HOWTO, available from
  14           <http://www.tldp.org/docs.html#howto>.
  15
  16           Note that the answer to this question doesn't directly affect the
  17           kernel: saying N will just cause the configurator to skip all
  18           the questions about Freescale devices. If you say Y, you will be
  19           asked for your specific card in the following questions.
  20
  21 if NET_VENDOR_FREESCALE
  22
  23 config FEC
  24         tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
  25         depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \
  26                    ARCH_MXC || SOC_IMX28)
  27         default ARCH_MXC || SOC_IMX28 if ARM
  28         select PHYLIB
  29         select PTP_1588_CLOCK
  30         ---help---
  31           Say Y here if you want to use the built-in 10/100 Fast ethernet
  32           controller on some Motorola ColdFire and Freescale i.MX processors.
  33
  34 config FEC_MPC52xx
  35         tristate "FEC MPC52xx driver"
  36         depends on PPC_MPC52xx && PPC_BESTCOMM
  37         select CRC32
  38         select PHYLIB
  39         select PPC_BESTCOMM_FEC
  40         ---help---
  41           This option enables support for the MPC5200's on-chip
  42           Fast Ethernet Controller
  43           If compiled as module, it will be called fec_mpc52xx.
  44
  45 config FEC_MPC52xx_MDIO
  46         bool "FEC MPC52xx MDIO bus driver"
  47         depends on FEC_MPC52xx
  48         default y
  49         ---help---
  50           The MPC5200's FEC can connect to the Ethernet either with
  51           an external MII PHY chip or 10 Mbps 7-wire interface
  52           (Motorola? industry standard).
  53           If your board uses an external PHY connected to FEC, enable this.
  54           If not sure, enable.
  55           If compiled as module, it will be called fec_mpc52xx_phy.
  56
  57 source "drivers/net/ethernet/freescale/fs_enet/Kconfig"
  58
  59 config FSL_PQ_MDIO
  60         tristate "Freescale PQ MDIO"
  61         select PHYLIB
  62         ---help---
  63           This driver supports the MDIO bus used by the gianfar and UCC drivers.
  64
  65 config FSL_XGMAC_MDIO
  66         tristate "Freescale XGMAC MDIO"
  67         select PHYLIB
  68         select OF_MDIO
  69         ---help---
  70           This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and
  71           on the FMan mEMAC (which supports both Clauses 22 and 45)
  72
  73 config UCC_GETH
  74         tristate "Freescale QE Gigabit Ethernet"
  75         depends on QUICC_ENGINE
  76         select FSL_PQ_MDIO
  77         select PHYLIB
  78         ---help---
  79           This driver supports the Gigabit Ethernet mode of the QUICC Engine,
  80           which is available on some Freescale SOCs.
  81
  82 config UGETH_TX_ON_DEMAND
  83         bool "Transmit on Demand support"
  84         depends on UCC_GETH
  85
  86 config GIANFAR
  87         tristate "Gianfar Ethernet"
  88         depends on FSL_SOC
  89         select FSL_PQ_MDIO
  90         select PHYLIB
  91         select CRC32
  92         ---help---
  93           This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
  94           and MPC86xx family of chips, and the FEC on the 8540.
  95
  96 endif # NET_VENDOR_FREESCALE