drivers/net/ethernet/marvell/Kconfig

   1 #
   2 # Marvell device configuration
   3 #
   4
   5 config NET_VENDOR_MARVELL
   6         bool "Marvell devices"
   7         default y
   8         depends on PCI || CPU_PXA168 || MV64X60 || PPC32 || PLAT_ORION || INET
   9         ---help---
  10           If you have a network (Ethernet) card belonging to this class, say Y
  11           and read the Ethernet-HOWTO, available from
  12           <http://www.tldp.org/docs.html#howto>.
  13
  14           Note that the answer to this question doesn't directly affect the
  15           kernel: saying N will just cause the configurator to skip all
  16           the questions about Marvell devices. If you say Y, you will be
  17           asked for your specific card in the following questions.
  18
  19 if NET_VENDOR_MARVELL
  20
  21 config MV643XX_ETH
  22         tristate "Marvell Discovery (643XX) and Orion ethernet support"
  23         depends on (MV64X60 || PPC32 || PLAT_ORION) && INET
  24         select PHYLIB
  25         select MVMDIO
  26         ---help---
  27           This driver supports the gigabit ethernet MACs in the
  28           Marvell Discovery PPC/MIPS chipset family (MV643XX) and
  29           in the Marvell Orion ARM SoC family.
  30
  31           Some boards that use the Discovery chipset are the Momenco
  32           Ocelot C and Jaguar ATX and Pegasos II.
  33
  34 config MVMDIO
  35         tristate "Marvell MDIO interface support"
  36         depends on HAS_IOMEM
  37         select PHYLIB
  38         ---help---
  39           This driver supports the MDIO interface found in the network
  40           interface units of the Marvell EBU SoCs (Kirkwood, Orion5x,
  41           Dove, Armada 370 and Armada XP).
  42
  43           This driver is used by the MV643XX_ETH and MVNETA drivers.
  44
  45 config MVNETA
  46         tristate "Marvell Armada 370/38x/XP network interface support"
  47         depends on PLAT_ORION
  48         select MVMDIO
  49         ---help---
  50           This driver supports the network interface units in the
  51           Marvell ARMADA XP, ARMADA 370 and ARMADA 38x SoC family.
  52
  53           Note that this driver is distinct from the mv643xx_eth
  54           driver, which should be used for the older Marvell SoCs
  55           (Dove, Orion, Discovery, Kirkwood).
  56
  57 config MVPP2
  58         tristate "Marvell Armada 375 network interface support"
  59         depends on MACH_ARMADA_375
  60         select MVMDIO
  61         ---help---
  62           This driver supports the network interface units in the
  63           Marvell ARMADA 375 SoC.
  64
  65 config PXA168_ETH
  66         tristate "Marvell pxa168 ethernet support"
  67         depends on HAS_IOMEM && HAS_DMA
  68         depends on CPU_PXA168 || ARCH_BERLIN || COMPILE_TEST
  69         select PHYLIB
  70         ---help---
  71           This driver supports the pxa168 Ethernet ports.
  72
  73           To compile this driver as a module, choose M here. The module
  74           will be called pxa168_eth.
  75
  76 config SKGE
  77         tristate "Marvell Yukon Gigabit Ethernet support"
  78         depends on PCI
  79         select CRC32
  80         ---help---
  81           This driver support the Marvell Yukon or SysKonnect SK-98xx/SK-95xx
  82           and related Gigabit Ethernet adapters. It is a new smaller driver
  83           with better performance and more complete ethtool support.
  84
  85           It does not support the link failover and network management
  86           features that "portable" vendor supplied sk98lin driver does.
  87
  88           This driver supports adapters based on the original Yukon chipset:
  89           Marvell 88E8001, Belkin F5D5005, CNet GigaCard, DLink DGE-530T,
  90           Linksys EG1032/EG1064, 3Com 3C940/3C940B, SysKonnect SK-9871/9872.
  91
  92           It does not support the newer Yukon2 chipset: a separate driver,
  93           sky2, is provided for these adapters.
  94
  95           To compile this driver as a module, choose M here: the module
  96           will be called skge.  This is recommended.
  97
  98 config SKGE_DEBUG
  99         bool "Debugging interface"
 100         depends on SKGE && DEBUG_FS
 101         ---help---
 102           This option adds the ability to dump driver state for debugging.
 103           The file /sys/kernel/debug/skge/ethX displays the state of the internal
 104           transmit and receive rings.
 105
 106           If unsure, say N.
 107
 108 config SKGE_GENESIS
 109         bool "Support for older SysKonnect Genesis boards"
 110         depends on SKGE
 111         ---help---
 112          This enables support for the older and uncommon SysKonnect Genesis
 113          chips, which support MII via an external transceiver, instead of
 114          an internal one. Disabling this option will save some memory
 115          by making code smaller. If unsure say Y.
 116
 117 config SKY2
 118         tristate "Marvell Yukon 2 support"
 119         depends on PCI
 120         select CRC32
 121         ---help---
 122           This driver supports Gigabit Ethernet adapters based on the
 123           Marvell Yukon 2 chipset:
 124           Marvell 88E8021/88E8022/88E8035/88E8036/88E8038/88E8050/88E8052/
 125           88E8053/88E8055/88E8061/88E8062, SysKonnect SK-9E21D/SK-9S21
 126
 127           There is companion driver for the older Marvell Yukon and
 128           SysKonnect Genesis based adapters: skge.
 129
 130           To compile this driver as a module, choose M here: the module
 131           will be called sky2.  This is recommended.
 132
 133 config SKY2_DEBUG
 134         bool "Debugging interface"
 135         depends on SKY2 && DEBUG_FS
 136         ---help---
 137           This option adds the ability to dump driver state for debugging.
 138           The file /sys/kernel/debug/sky2/ethX displays the state of the internal
 139           transmit and receive rings.
 140
 141           If unsure, say N.
 142
 143 endif # NET_VENDOR_MARVELL