1 /*******************************************************************************
2 This is the driver for the ST MAC 10/100/1000 on-chip Ethernet controllers.
3 ST Ethernet IPs are built around a Synopsys IP Core.
5 Copyright(C) 2007-2011 STMicroelectronics Ltd
7 This program is free software; you can redistribute it and/or modify it
8 under the terms and conditions of the GNU General Public License,
9 version 2, as published by the Free Software Foundation.
11 This program is distributed in the hope it will be useful, but WITHOUT
12 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
13 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
16 You should have received a copy of the GNU General Public License along with
17 this program; if not, write to the Free Software Foundation, Inc.,
18 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
20 The full GNU General Public License is included in this distribution in
21 the file called "COPYING".
23 Author: Giuseppe Cavallaro <peppe.cavallaro@st.com>
25 Documentation available at:
26 http://www.stlinux.com
28 https://bugzilla.stlinux.com/
29 *******************************************************************************/
31 #include <linux/clk.h>
32 #include <linux/kernel.h>
33 #include <linux/interrupt.h>
35 #include <linux/tcp.h>
36 #include <linux/skbuff.h>
37 #include <linux/ethtool.h>
38 #include <linux/if_ether.h>
39 #include <linux/crc32.h>
40 #include <linux/mii.h>
42 #include <linux/if_vlan.h>
43 #include <linux/dma-mapping.h>
44 #include <linux/slab.h>
45 #include <linux/prefetch.h>
46 #include <linux/pinctrl/consumer.h>
47 #ifdef CONFIG_DEBUG_FS
48 #include <linux/debugfs.h>
49 #include <linux/seq_file.h>
50 #endif /* CONFIG_DEBUG_FS */
51 #include <linux/net_tstamp.h>
52 #include "stmmac_ptp.h"
54 #include <linux/reset.h>
56 #define STMMAC_ALIGN(x) L1_CACHE_ALIGN(x)
58 /* Module parameters */
60 static int watchdog
= TX_TIMEO
;
61 module_param(watchdog
, int, S_IRUGO
| S_IWUSR
);
62 MODULE_PARM_DESC(watchdog
, "Transmit timeout in milliseconds (default 5s)");
64 static int debug
= -1;
65 module_param(debug
, int, S_IRUGO
| S_IWUSR
);
66 MODULE_PARM_DESC(debug
, "Message Level (-1: default, 0: no output, 16: all)");
68 static int phyaddr
= -1;
69 module_param(phyaddr
, int, S_IRUGO
);
70 MODULE_PARM_DESC(phyaddr
, "Physical device address");
72 #define DMA_TX_SIZE 256
73 static int dma_txsize
= DMA_TX_SIZE
;
74 module_param(dma_txsize
, int, S_IRUGO
| S_IWUSR
);
75 MODULE_PARM_DESC(dma_txsize
, "Number of descriptors in the TX list");
77 #define DMA_RX_SIZE 256
78 static int dma_rxsize
= DMA_RX_SIZE
;
79 module_param(dma_rxsize
, int, S_IRUGO
| S_IWUSR
);
80 MODULE_PARM_DESC(dma_rxsize
, "Number of descriptors in the RX list");
82 static int flow_ctrl
= FLOW_OFF
;
83 module_param(flow_ctrl
, int, S_IRUGO
| S_IWUSR
);
84 MODULE_PARM_DESC(flow_ctrl
, "Flow control ability [on/off]");
86 static int pause
= PAUSE_TIME
;
87 module_param(pause
, int, S_IRUGO
| S_IWUSR
);
88 MODULE_PARM_DESC(pause
, "Flow Control Pause Time");
91 static int tc
= TC_DEFAULT
;
92 module_param(tc
, int, S_IRUGO
| S_IWUSR
);
93 MODULE_PARM_DESC(tc
, "DMA threshold control value");
95 #define DEFAULT_BUFSIZE 1536
96 static int buf_sz
= DEFAULT_BUFSIZE
;
97 module_param(buf_sz
, int, S_IRUGO
| S_IWUSR
);
98 MODULE_PARM_DESC(buf_sz
, "DMA buffer size");
100 static const u32 default_msg_level
= (NETIF_MSG_DRV
| NETIF_MSG_PROBE
|
101 NETIF_MSG_LINK
| NETIF_MSG_IFUP
|
102 NETIF_MSG_IFDOWN
| NETIF_MSG_TIMER
);
104 #define STMMAC_DEFAULT_LPI_TIMER 1000
105 static int eee_timer
= STMMAC_DEFAULT_LPI_TIMER
;
106 module_param(eee_timer
, int, S_IRUGO
| S_IWUSR
);
107 MODULE_PARM_DESC(eee_timer
, "LPI tx expiration time in msec");
108 #define STMMAC_LPI_T(x) (jiffies + msecs_to_jiffies(x))
110 /* By default the driver will use the ring mode to manage tx and rx descriptors
111 * but passing this value so user can force to use the chain instead of the ring
113 static unsigned int chain_mode
;
114 module_param(chain_mode
, int, S_IRUGO
);
115 MODULE_PARM_DESC(chain_mode
, "To use chain instead of ring mode");
117 static irqreturn_t
stmmac_interrupt(int irq
, void *dev_id
);
119 #ifdef CONFIG_DEBUG_FS
120 static int stmmac_init_fs(struct net_device
*dev
);
121 static void stmmac_exit_fs(void);
124 #define STMMAC_COAL_TIMER(x) (jiffies + usecs_to_jiffies(x))
127 * stmmac_verify_args - verify the driver parameters.
128 * Description: it checks the driver parameters and set a default in case of
131 static void stmmac_verify_args(void)
133 if (unlikely(watchdog
< 0))
135 if (unlikely(dma_rxsize
< 0))
136 dma_rxsize
= DMA_RX_SIZE
;
137 if (unlikely(dma_txsize
< 0))
138 dma_txsize
= DMA_TX_SIZE
;
139 if (unlikely((buf_sz
< DEFAULT_BUFSIZE
) || (buf_sz
> BUF_SIZE_16KiB
)))
140 buf_sz
= DEFAULT_BUFSIZE
;
141 if (unlikely(flow_ctrl
> 1))
142 flow_ctrl
= FLOW_AUTO
;
143 else if (likely(flow_ctrl
< 0))
144 flow_ctrl
= FLOW_OFF
;
145 if (unlikely((pause
< 0) || (pause
> 0xffff)))
148 eee_timer
= STMMAC_DEFAULT_LPI_TIMER
;
152 * stmmac_clk_csr_set - dynamically set the MDC clock
153 * @priv: driver private structure
154 * Description: this is to dynamically set the MDC clock according to the csr
157 * If a specific clk_csr value is passed from the platform
158 * this means that the CSR Clock Range selection cannot be
159 * changed at run-time and it is fixed (as reported in the driver
160 * documentation). Viceversa the driver will try to set the MDC
161 * clock dynamically according to the actual clock input.
163 static void stmmac_clk_csr_set(struct stmmac_priv
*priv
)
167 clk_rate
= clk_get_rate(priv
->stmmac_clk
);
169 /* Platform provided default clk_csr would be assumed valid
170 * for all other cases except for the below mentioned ones.
171 * For values higher than the IEEE 802.3 specified frequency
172 * we can not estimate the proper divider as it is not known
173 * the frequency of clk_csr_i. So we do not change the default
176 if (!(priv
->clk_csr
& MAC_CSR_H_FRQ_MASK
)) {
177 if (clk_rate
< CSR_F_35M
)
178 priv
->clk_csr
= STMMAC_CSR_20_35M
;
179 else if ((clk_rate
>= CSR_F_35M
) && (clk_rate
< CSR_F_60M
))
180 priv
->clk_csr
= STMMAC_CSR_35_60M
;
181 else if ((clk_rate
>= CSR_F_60M
) && (clk_rate
< CSR_F_100M
))
182 priv
->clk_csr
= STMMAC_CSR_60_100M
;
183 else if ((clk_rate
>= CSR_F_100M
) && (clk_rate
< CSR_F_150M
))
184 priv
->clk_csr
= STMMAC_CSR_100_150M
;
185 else if ((clk_rate
>= CSR_F_150M
) && (clk_rate
< CSR_F_250M
))
186 priv
->clk_csr
= STMMAC_CSR_150_250M
;
187 else if ((clk_rate
>= CSR_F_250M
) && (clk_rate
< CSR_F_300M
))
188 priv
->clk_csr
= STMMAC_CSR_250_300M
;
192 static void print_pkt(unsigned char *buf
, int len
)
194 pr_debug("len = %d byte, buf addr: 0x%p\n", len
, buf
);
195 print_hex_dump_bytes("", DUMP_PREFIX_OFFSET
, buf
, len
);
198 /* minimum number of free TX descriptors required to wake up TX process */
199 #define STMMAC_TX_THRESH(x) (x->dma_tx_size/4)
201 static inline u32
stmmac_tx_avail(struct stmmac_priv
*priv
)
203 return priv
->dirty_tx
+ priv
->dma_tx_size
- priv
->cur_tx
- 1;
207 * stmmac_hw_fix_mac_speed - callback for speed selection
208 * @priv: driver private structure
209 * Description: on some platforms (e.g. ST), some HW system configuraton
210 * registers have to be set according to the link speed negotiated.
212 static inline void stmmac_hw_fix_mac_speed(struct stmmac_priv
*priv
)
214 struct phy_device
*phydev
= priv
->phydev
;
216 if (likely(priv
->plat
->fix_mac_speed
))
217 priv
->plat
->fix_mac_speed(priv
->plat
->bsp_priv
, phydev
->speed
);
221 * stmmac_enable_eee_mode - check and enter in LPI mode
222 * @priv: driver private structure
223 * Description: this function is to verify and enter in LPI mode in case of
226 static void stmmac_enable_eee_mode(struct stmmac_priv
*priv
)
228 /* Check and enter in LPI mode */
229 if ((priv
->dirty_tx
== priv
->cur_tx
) &&
230 (priv
->tx_path_in_lpi_mode
== false))
231 priv
->hw
->mac
->set_eee_mode(priv
->hw
);
235 * stmmac_disable_eee_mode - disable and exit from LPI mode
236 * @priv: driver private structure
237 * Description: this function is to exit and disable EEE in case of
238 * LPI state is true. This is called by the xmit.
240 void stmmac_disable_eee_mode(struct stmmac_priv
*priv
)
242 priv
->hw
->mac
->reset_eee_mode(priv
->hw
);
243 del_timer_sync(&priv
->eee_ctrl_timer
);
244 priv
->tx_path_in_lpi_mode
= false;
248 * stmmac_eee_ctrl_timer - EEE TX SW timer.
251 * if there is no data transfer and if we are not in LPI state,
252 * then MAC Transmitter can be moved to LPI state.
254 static void stmmac_eee_ctrl_timer(unsigned long arg
)
256 struct stmmac_priv
*priv
= (struct stmmac_priv
*)arg
;
258 stmmac_enable_eee_mode(priv
);
259 mod_timer(&priv
->eee_ctrl_timer
, STMMAC_LPI_T(eee_timer
));
263 * stmmac_eee_init - init EEE
264 * @priv: driver private structure
266 * if the GMAC supports the EEE (from the HW cap reg) and the phy device
267 * can also manage EEE, this function enable the LPI state and start related
270 bool stmmac_eee_init(struct stmmac_priv
*priv
)
272 char *phy_bus_name
= priv
->plat
->phy_bus_name
;
276 /* Using PCS we cannot dial with the phy registers at this stage
277 * so we do not support extra feature like EEE.
279 if ((priv
->pcs
== STMMAC_PCS_RGMII
) || (priv
->pcs
== STMMAC_PCS_TBI
) ||
280 (priv
->pcs
== STMMAC_PCS_RTBI
))
283 /* Never init EEE in case of a switch is attached */
284 if (phy_bus_name
&& (!strcmp(phy_bus_name
, "fixed")))
287 /* MAC core supports the EEE feature. */
288 if (priv
->dma_cap
.eee
) {
289 int tx_lpi_timer
= priv
->tx_lpi_timer
;
291 /* Check if the PHY supports EEE */
292 if (phy_init_eee(priv
->phydev
, 1)) {
293 /* To manage at run-time if the EEE cannot be supported
294 * anymore (for example because the lp caps have been
296 * In that case the driver disable own timers.
298 spin_lock_irqsave(&priv
->lock
, flags
);
299 if (priv
->eee_active
) {
300 pr_debug("stmmac: disable EEE\n");
301 del_timer_sync(&priv
->eee_ctrl_timer
);
302 priv
->hw
->mac
->set_eee_timer(priv
->hw
, 0,
305 priv
->eee_active
= 0;
306 spin_unlock_irqrestore(&priv
->lock
, flags
);
309 /* Activate the EEE and start timers */
310 spin_lock_irqsave(&priv
->lock
, flags
);
311 if (!priv
->eee_active
) {
312 priv
->eee_active
= 1;
313 setup_timer(&priv
->eee_ctrl_timer
,
314 stmmac_eee_ctrl_timer
,
315 (unsigned long)priv
);
316 mod_timer(&priv
->eee_ctrl_timer
,
317 STMMAC_LPI_T(eee_timer
));
319 priv
->hw
->mac
->set_eee_timer(priv
->hw
,
320 STMMAC_DEFAULT_LIT_LS
,
323 /* Set HW EEE according to the speed */
324 priv
->hw
->mac
->set_eee_pls(priv
->hw
, priv
->phydev
->link
);
327 spin_unlock_irqrestore(&priv
->lock
, flags
);
329 pr_debug("stmmac: Energy-Efficient Ethernet initialized\n");
335 /* stmmac_get_tx_hwtstamp - get HW TX timestamps
336 * @priv: driver private structure
337 * @entry : descriptor index to be used.
338 * @skb : the socket buffer
340 * This function will read timestamp from the descriptor & pass it to stack.
341 * and also perform some sanity checks.
343 static void stmmac_get_tx_hwtstamp(struct stmmac_priv
*priv
,
344 unsigned int entry
, struct sk_buff
*skb
)
346 struct skb_shared_hwtstamps shhwtstamp
;
350 if (!priv
->hwts_tx_en
)
353 /* exit if skb doesn't support hw tstamp */
354 if (likely(!skb
|| !(skb_shinfo(skb
)->tx_flags
& SKBTX_IN_PROGRESS
)))
358 desc
= (priv
->dma_etx
+ entry
);
360 desc
= (priv
->dma_tx
+ entry
);
362 /* check tx tstamp status */
363 if (!priv
->hw
->desc
->get_tx_timestamp_status((struct dma_desc
*)desc
))
366 /* get the valid tstamp */
367 ns
= priv
->hw
->desc
->get_timestamp(desc
, priv
->adv_ts
);
369 memset(&shhwtstamp
, 0, sizeof(struct skb_shared_hwtstamps
));
370 shhwtstamp
.hwtstamp
= ns_to_ktime(ns
);
371 /* pass tstamp to stack */
372 skb_tstamp_tx(skb
, &shhwtstamp
);
377 /* stmmac_get_rx_hwtstamp - get HW RX timestamps
378 * @priv: driver private structure
379 * @entry : descriptor index to be used.
380 * @skb : the socket buffer
382 * This function will read received packet's timestamp from the descriptor
383 * and pass it to stack. It also perform some sanity checks.
385 static void stmmac_get_rx_hwtstamp(struct stmmac_priv
*priv
,
386 unsigned int entry
, struct sk_buff
*skb
)
388 struct skb_shared_hwtstamps
*shhwtstamp
= NULL
;
392 if (!priv
->hwts_rx_en
)
396 desc
= (priv
->dma_erx
+ entry
);
398 desc
= (priv
->dma_rx
+ entry
);
400 /* exit if rx tstamp is not valid */
401 if (!priv
->hw
->desc
->get_rx_timestamp_status(desc
, priv
->adv_ts
))
404 /* get valid tstamp */
405 ns
= priv
->hw
->desc
->get_timestamp(desc
, priv
->adv_ts
);
406 shhwtstamp
= skb_hwtstamps(skb
);
407 memset(shhwtstamp
, 0, sizeof(struct skb_shared_hwtstamps
));
408 shhwtstamp
->hwtstamp
= ns_to_ktime(ns
);
412 * stmmac_hwtstamp_ioctl - control hardware timestamping.
413 * @dev: device pointer.
414 * @ifr: An IOCTL specefic structure, that can contain a pointer to
415 * a proprietary structure used to pass information to the driver.
417 * This function configures the MAC to enable/disable both outgoing(TX)
418 * and incoming(RX) packets time stamping based on user input.
420 * 0 on success and an appropriate -ve integer on failure.
422 static int stmmac_hwtstamp_ioctl(struct net_device
*dev
, struct ifreq
*ifr
)
424 struct stmmac_priv
*priv
= netdev_priv(dev
);
425 struct hwtstamp_config config
;
430 u32 ptp_over_ipv4_udp
= 0;
431 u32 ptp_over_ipv6_udp
= 0;
432 u32 ptp_over_ethernet
= 0;
433 u32 snap_type_sel
= 0;
434 u32 ts_master_en
= 0;
438 if (!(priv
->dma_cap
.time_stamp
|| priv
->adv_ts
)) {
439 netdev_alert(priv
->dev
, "No support for HW time stamping\n");
440 priv
->hwts_tx_en
= 0;
441 priv
->hwts_rx_en
= 0;
446 if (copy_from_user(&config
, ifr
->ifr_data
,
447 sizeof(struct hwtstamp_config
)))
450 pr_debug("%s config flags:0x%x, tx_type:0x%x, rx_filter:0x%x\n",
451 __func__
, config
.flags
, config
.tx_type
, config
.rx_filter
);
453 /* reserved for future extensions */
457 if (config
.tx_type
!= HWTSTAMP_TX_OFF
&&
458 config
.tx_type
!= HWTSTAMP_TX_ON
)
462 switch (config
.rx_filter
) {
463 case HWTSTAMP_FILTER_NONE
:
464 /* time stamp no incoming packet at all */
465 config
.rx_filter
= HWTSTAMP_FILTER_NONE
;
468 case HWTSTAMP_FILTER_PTP_V1_L4_EVENT
:
469 /* PTP v1, UDP, any kind of event packet */
470 config
.rx_filter
= HWTSTAMP_FILTER_PTP_V1_L4_EVENT
;
471 /* take time stamp for all event messages */
472 snap_type_sel
= PTP_TCR_SNAPTYPSEL_1
;
474 ptp_over_ipv4_udp
= PTP_TCR_TSIPV4ENA
;
475 ptp_over_ipv6_udp
= PTP_TCR_TSIPV6ENA
;
478 case HWTSTAMP_FILTER_PTP_V1_L4_SYNC
:
479 /* PTP v1, UDP, Sync packet */
480 config
.rx_filter
= HWTSTAMP_FILTER_PTP_V1_L4_SYNC
;
481 /* take time stamp for SYNC messages only */
482 ts_event_en
= PTP_TCR_TSEVNTENA
;
484 ptp_over_ipv4_udp
= PTP_TCR_TSIPV4ENA
;
485 ptp_over_ipv6_udp
= PTP_TCR_TSIPV6ENA
;
488 case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ
:
489 /* PTP v1, UDP, Delay_req packet */
490 config
.rx_filter
= HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ
;
491 /* take time stamp for Delay_Req messages only */
492 ts_master_en
= PTP_TCR_TSMSTRENA
;
493 ts_event_en
= PTP_TCR_TSEVNTENA
;
495 ptp_over_ipv4_udp
= PTP_TCR_TSIPV4ENA
;
496 ptp_over_ipv6_udp
= PTP_TCR_TSIPV6ENA
;
499 case HWTSTAMP_FILTER_PTP_V2_L4_EVENT
:
500 /* PTP v2, UDP, any kind of event packet */
501 config
.rx_filter
= HWTSTAMP_FILTER_PTP_V2_L4_EVENT
;
502 ptp_v2
= PTP_TCR_TSVER2ENA
;
503 /* take time stamp for all event messages */
504 snap_type_sel
= PTP_TCR_SNAPTYPSEL_1
;
506 ptp_over_ipv4_udp
= PTP_TCR_TSIPV4ENA
;
507 ptp_over_ipv6_udp
= PTP_TCR_TSIPV6ENA
;
510 case HWTSTAMP_FILTER_PTP_V2_L4_SYNC
:
511 /* PTP v2, UDP, Sync packet */
512 config
.rx_filter
= HWTSTAMP_FILTER_PTP_V2_L4_SYNC
;
513 ptp_v2
= PTP_TCR_TSVER2ENA
;
514 /* take time stamp for SYNC messages only */
515 ts_event_en
= PTP_TCR_TSEVNTENA
;
517 ptp_over_ipv4_udp
= PTP_TCR_TSIPV4ENA
;
518 ptp_over_ipv6_udp
= PTP_TCR_TSIPV6ENA
;
521 case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ
:
522 /* PTP v2, UDP, Delay_req packet */
523 config
.rx_filter
= HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ
;
524 ptp_v2
= PTP_TCR_TSVER2ENA
;
525 /* take time stamp for Delay_Req messages only */
526 ts_master_en
= PTP_TCR_TSMSTRENA
;
527 ts_event_en
= PTP_TCR_TSEVNTENA
;
529 ptp_over_ipv4_udp
= PTP_TCR_TSIPV4ENA
;
530 ptp_over_ipv6_udp
= PTP_TCR_TSIPV6ENA
;
533 case HWTSTAMP_FILTER_PTP_V2_EVENT
:
534 /* PTP v2/802.AS1 any layer, any kind of event packet */
535 config
.rx_filter
= HWTSTAMP_FILTER_PTP_V2_EVENT
;
536 ptp_v2
= PTP_TCR_TSVER2ENA
;
537 /* take time stamp for all event messages */
538 snap_type_sel
= PTP_TCR_SNAPTYPSEL_1
;
540 ptp_over_ipv4_udp
= PTP_TCR_TSIPV4ENA
;
541 ptp_over_ipv6_udp
= PTP_TCR_TSIPV6ENA
;
542 ptp_over_ethernet
= PTP_TCR_TSIPENA
;
545 case HWTSTAMP_FILTER_PTP_V2_SYNC
:
546 /* PTP v2/802.AS1, any layer, Sync packet */
547 config
.rx_filter
= HWTSTAMP_FILTER_PTP_V2_SYNC
;
548 ptp_v2
= PTP_TCR_TSVER2ENA
;
549 /* take time stamp for SYNC messages only */
550 ts_event_en
= PTP_TCR_TSEVNTENA
;
552 ptp_over_ipv4_udp
= PTP_TCR_TSIPV4ENA
;
553 ptp_over_ipv6_udp
= PTP_TCR_TSIPV6ENA
;
554 ptp_over_ethernet
= PTP_TCR_TSIPENA
;
557 case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ
:
558 /* PTP v2/802.AS1, any layer, Delay_req packet */
559 config
.rx_filter
= HWTSTAMP_FILTER_PTP_V2_DELAY_REQ
;
560 ptp_v2
= PTP_TCR_TSVER2ENA
;
561 /* take time stamp for Delay_Req messages only */
562 ts_master_en
= PTP_TCR_TSMSTRENA
;
563 ts_event_en
= PTP_TCR_TSEVNTENA
;
565 ptp_over_ipv4_udp
= PTP_TCR_TSIPV4ENA
;
566 ptp_over_ipv6_udp
= PTP_TCR_TSIPV6ENA
;
567 ptp_over_ethernet
= PTP_TCR_TSIPENA
;
570 case HWTSTAMP_FILTER_ALL
:
571 /* time stamp any incoming packet */
572 config
.rx_filter
= HWTSTAMP_FILTER_ALL
;
573 tstamp_all
= PTP_TCR_TSENALL
;
580 switch (config
.rx_filter
) {
581 case HWTSTAMP_FILTER_NONE
:
582 config
.rx_filter
= HWTSTAMP_FILTER_NONE
;
585 /* PTP v1, UDP, any kind of event packet */
586 config
.rx_filter
= HWTSTAMP_FILTER_PTP_V1_L4_EVENT
;
590 priv
->hwts_rx_en
= ((config
.rx_filter
== HWTSTAMP_FILTER_NONE
) ? 0 : 1);
591 priv
->hwts_tx_en
= config
.tx_type
== HWTSTAMP_TX_ON
;
593 if (!priv
->hwts_tx_en
&& !priv
->hwts_rx_en
)
594 priv
->hw
->ptp
->config_hw_tstamping(priv
->ioaddr
, 0);
596 value
= (PTP_TCR_TSENA
| PTP_TCR_TSCFUPDT
| PTP_TCR_TSCTRLSSR
|
597 tstamp_all
| ptp_v2
| ptp_over_ethernet
|
598 ptp_over_ipv6_udp
| ptp_over_ipv4_udp
| ts_event_en
|
599 ts_master_en
| snap_type_sel
);
601 priv
->hw
->ptp
->config_hw_tstamping(priv
->ioaddr
, value
);
603 /* program Sub Second Increment reg */
604 priv
->hw
->ptp
->config_sub_second_increment(priv
->ioaddr
);
606 /* calculate default added value:
608 * addend = (2^32)/freq_div_ratio;
609 * where, freq_div_ratio = clk_ptp_ref_i/50MHz
610 * hence, addend = ((2^32) * 50MHz)/clk_ptp_ref_i;
611 * NOTE: clk_ptp_ref_i should be >= 50MHz to
612 * achive 20ns accuracy.
614 * 2^x * y == (y << x), hence
615 * 2^32 * 50000000 ==> (50000000 << 32)
617 temp
= (u64
) (50000000ULL << 32);
618 priv
->default_addend
= div_u64(temp
, priv
->clk_ptp_rate
);
619 priv
->hw
->ptp
->config_addend(priv
->ioaddr
,
620 priv
->default_addend
);
622 /* initialize system time */
623 getnstimeofday(&now
);
624 priv
->hw
->ptp
->init_systime(priv
->ioaddr
, now
.tv_sec
,
628 return copy_to_user(ifr
->ifr_data
, &config
,
629 sizeof(struct hwtstamp_config
)) ? -EFAULT
: 0;
633 * stmmac_init_ptp - init PTP
634 * @priv: driver private structure
635 * Description: this is to verify if the HW supports the PTPv1 or PTPv2.
636 * This is done by looking at the HW cap. register.
637 * This function also registers the ptp driver.
639 static int stmmac_init_ptp(struct stmmac_priv
*priv
)
641 if (!(priv
->dma_cap
.time_stamp
|| priv
->dma_cap
.atime_stamp
))
644 /* Fall-back to main clock in case of no PTP ref is passed */
645 priv
->clk_ptp_ref
= devm_clk_get(priv
->device
, "clk_ptp_ref");
646 if (IS_ERR(priv
->clk_ptp_ref
)) {
647 priv
->clk_ptp_rate
= clk_get_rate(priv
->stmmac_clk
);
648 priv
->clk_ptp_ref
= NULL
;
650 clk_prepare_enable(priv
->clk_ptp_ref
);
651 priv
->clk_ptp_rate
= clk_get_rate(priv
->clk_ptp_ref
);
655 if (priv
->dma_cap
.atime_stamp
&& priv
->extend_desc
)
658 if (netif_msg_hw(priv
) && priv
->dma_cap
.time_stamp
)
659 pr_debug("IEEE 1588-2002 Time Stamp supported\n");
661 if (netif_msg_hw(priv
) && priv
->adv_ts
)
662 pr_debug("IEEE 1588-2008 Advanced Time Stamp supported\n");
664 priv
->hw
->ptp
= &stmmac_ptp
;
665 priv
->hwts_tx_en
= 0;
666 priv
->hwts_rx_en
= 0;
668 return stmmac_ptp_register(priv
);
671 static void stmmac_release_ptp(struct stmmac_priv
*priv
)
673 if (priv
->clk_ptp_ref
)
674 clk_disable_unprepare(priv
->clk_ptp_ref
);
675 stmmac_ptp_unregister(priv
);
679 * stmmac_adjust_link - adjusts the link parameters
680 * @dev: net device structure
681 * Description: this is the helper called by the physical abstraction layer
682 * drivers to communicate the phy link status. According the speed and duplex
683 * this driver can invoke registered glue-logic as well.
684 * It also invoke the eee initialization because it could happen when switch
685 * on different networks (that are eee capable).
687 static void stmmac_adjust_link(struct net_device
*dev
)
689 struct stmmac_priv
*priv
= netdev_priv(dev
);
690 struct phy_device
*phydev
= priv
->phydev
;
693 unsigned int fc
= priv
->flow_ctrl
, pause_time
= priv
->pause
;
698 spin_lock_irqsave(&priv
->lock
, flags
);
701 u32 ctrl
= readl(priv
->ioaddr
+ MAC_CTRL_REG
);
703 /* Now we make sure that we can be in full duplex mode.
704 * If not, we operate in half-duplex mode. */
705 if (phydev
->duplex
!= priv
->oldduplex
) {
707 if (!(phydev
->duplex
))
708 ctrl
&= ~priv
->hw
->link
.duplex
;
710 ctrl
|= priv
->hw
->link
.duplex
;
711 priv
->oldduplex
= phydev
->duplex
;
713 /* Flow Control operation */
715 priv
->hw
->mac
->flow_ctrl(priv
->hw
, phydev
->duplex
,
718 if (phydev
->speed
!= priv
->speed
) {
720 switch (phydev
->speed
) {
722 if (likely(priv
->plat
->has_gmac
))
723 ctrl
&= ~priv
->hw
->link
.port
;
724 stmmac_hw_fix_mac_speed(priv
);
728 if (priv
->plat
->has_gmac
) {
729 ctrl
|= priv
->hw
->link
.port
;
730 if (phydev
->speed
== SPEED_100
) {
731 ctrl
|= priv
->hw
->link
.speed
;
733 ctrl
&= ~(priv
->hw
->link
.speed
);
736 ctrl
&= ~priv
->hw
->link
.port
;
738 stmmac_hw_fix_mac_speed(priv
);
741 if (netif_msg_link(priv
))
742 pr_warn("%s: Speed (%d) not 10/100\n",
743 dev
->name
, phydev
->speed
);
747 priv
->speed
= phydev
->speed
;
750 writel(ctrl
, priv
->ioaddr
+ MAC_CTRL_REG
);
752 if (!priv
->oldlink
) {
756 } else if (priv
->oldlink
) {
760 priv
->oldduplex
= -1;
763 if (new_state
&& netif_msg_link(priv
))
764 phy_print_status(phydev
);
766 spin_unlock_irqrestore(&priv
->lock
, flags
);
768 /* At this stage, it could be needed to setup the EEE or adjust some
769 * MAC related HW registers.
771 priv
->eee_enabled
= stmmac_eee_init(priv
);
775 * stmmac_check_pcs_mode - verify if RGMII/SGMII is supported
776 * @priv: driver private structure
777 * Description: this is to verify if the HW supports the PCS.
778 * Physical Coding Sublayer (PCS) interface that can be used when the MAC is
779 * configured for the TBI, RTBI, or SGMII PHY interface.
781 static void stmmac_check_pcs_mode(struct stmmac_priv
*priv
)
783 int interface
= priv
->plat
->interface
;
785 if (priv
->dma_cap
.pcs
) {
786 if ((interface
== PHY_INTERFACE_MODE_RGMII
) ||
787 (interface
== PHY_INTERFACE_MODE_RGMII_ID
) ||
788 (interface
== PHY_INTERFACE_MODE_RGMII_RXID
) ||
789 (interface
== PHY_INTERFACE_MODE_RGMII_TXID
)) {
790 pr_debug("STMMAC: PCS RGMII support enable\n");
791 priv
->pcs
= STMMAC_PCS_RGMII
;
792 } else if (interface
== PHY_INTERFACE_MODE_SGMII
) {
793 pr_debug("STMMAC: PCS SGMII support enable\n");
794 priv
->pcs
= STMMAC_PCS_SGMII
;
800 * stmmac_init_phy - PHY initialization
801 * @dev: net device structure
802 * Description: it initializes the driver's PHY state, and attaches the PHY
807 static int stmmac_init_phy(struct net_device
*dev
)
809 struct stmmac_priv
*priv
= netdev_priv(dev
);
810 struct phy_device
*phydev
;
811 char phy_id_fmt
[MII_BUS_ID_SIZE
+ 3];
812 char bus_id
[MII_BUS_ID_SIZE
];
813 int interface
= priv
->plat
->interface
;
814 int max_speed
= priv
->plat
->max_speed
;
817 priv
->oldduplex
= -1;
819 if (priv
->plat
->phy_bus_name
)
820 snprintf(bus_id
, MII_BUS_ID_SIZE
, "%s-%x",
821 priv
->plat
->phy_bus_name
, priv
->plat
->bus_id
);
823 snprintf(bus_id
, MII_BUS_ID_SIZE
, "stmmac-%x",
826 snprintf(phy_id_fmt
, MII_BUS_ID_SIZE
+ 3, PHY_ID_FMT
, bus_id
,
827 priv
->plat
->phy_addr
);
828 pr_debug("stmmac_init_phy: trying to attach to %s\n", phy_id_fmt
);
830 phydev
= phy_connect(dev
, phy_id_fmt
, &stmmac_adjust_link
, interface
);
832 if (IS_ERR(phydev
)) {
833 pr_err("%s: Could not attach to PHY\n", dev
->name
);
834 return PTR_ERR(phydev
);
837 /* Stop Advertising 1000BASE Capability if interface is not GMII */
838 if ((interface
== PHY_INTERFACE_MODE_MII
) ||
839 (interface
== PHY_INTERFACE_MODE_RMII
) ||
840 (max_speed
< 1000 && max_speed
> 0))
841 phydev
->advertising
&= ~(SUPPORTED_1000baseT_Half
|
842 SUPPORTED_1000baseT_Full
);
845 * Broken HW is sometimes missing the pull-up resistor on the
846 * MDIO line, which results in reads to non-existent devices returning
847 * 0 rather than 0xffff. Catch this here and treat 0 as a non-existent
849 * Note: phydev->phy_id is the result of reading the UID PHY registers.
851 if (phydev
->phy_id
== 0) {
852 phy_disconnect(phydev
);
855 pr_debug("stmmac_init_phy: %s: attached to PHY (UID 0x%x)"
856 " Link = %d\n", dev
->name
, phydev
->phy_id
, phydev
->link
);
858 priv
->phydev
= phydev
;
864 * stmmac_display_ring - display ring
865 * @head: pointer to the head of the ring passed.
866 * @size: size of the ring.
867 * @extend_desc: to verify if extended descriptors are used.
868 * Description: display the control/status and buffer descriptors.
870 static void stmmac_display_ring(void *head
, int size
, int extend_desc
)
873 struct dma_extended_desc
*ep
= (struct dma_extended_desc
*)head
;
874 struct dma_desc
*p
= (struct dma_desc
*)head
;
876 for (i
= 0; i
< size
; i
++) {
880 pr_info("%d [0x%x]: 0x%x 0x%x 0x%x 0x%x\n",
881 i
, (unsigned int)virt_to_phys(ep
),
882 (unsigned int)x
, (unsigned int)(x
>> 32),
883 ep
->basic
.des2
, ep
->basic
.des3
);
887 pr_info("%d [0x%x]: 0x%x 0x%x 0x%x 0x%x",
888 i
, (unsigned int)virt_to_phys(p
),
889 (unsigned int)x
, (unsigned int)(x
>> 32),
897 static void stmmac_display_rings(struct stmmac_priv
*priv
)
899 unsigned int txsize
= priv
->dma_tx_size
;
900 unsigned int rxsize
= priv
->dma_rx_size
;
902 if (priv
->extend_desc
) {
903 pr_info("Extended RX descriptor ring:\n");
904 stmmac_display_ring((void *)priv
->dma_erx
, rxsize
, 1);
905 pr_info("Extended TX descriptor ring:\n");
906 stmmac_display_ring((void *)priv
->dma_etx
, txsize
, 1);
908 pr_info("RX descriptor ring:\n");
909 stmmac_display_ring((void *)priv
->dma_rx
, rxsize
, 0);
910 pr_info("TX descriptor ring:\n");
911 stmmac_display_ring((void *)priv
->dma_tx
, txsize
, 0);
915 static int stmmac_set_bfsize(int mtu
, int bufsize
)
919 if (mtu
>= BUF_SIZE_4KiB
)
921 else if (mtu
>= BUF_SIZE_2KiB
)
923 else if (mtu
> DEFAULT_BUFSIZE
)
926 ret
= DEFAULT_BUFSIZE
;
932 * stmmac_clear_descriptors - clear descriptors
933 * @priv: driver private structure
934 * Description: this function is called to clear the tx and rx descriptors
935 * in case of both basic and extended descriptors are used.
937 static void stmmac_clear_descriptors(struct stmmac_priv
*priv
)
940 unsigned int txsize
= priv
->dma_tx_size
;
941 unsigned int rxsize
= priv
->dma_rx_size
;
943 /* Clear the Rx/Tx descriptors */
944 for (i
= 0; i
< rxsize
; i
++)
945 if (priv
->extend_desc
)
946 priv
->hw
->desc
->init_rx_desc(&priv
->dma_erx
[i
].basic
,
947 priv
->use_riwt
, priv
->mode
,
950 priv
->hw
->desc
->init_rx_desc(&priv
->dma_rx
[i
],
951 priv
->use_riwt
, priv
->mode
,
953 for (i
= 0; i
< txsize
; i
++)
954 if (priv
->extend_desc
)
955 priv
->hw
->desc
->init_tx_desc(&priv
->dma_etx
[i
].basic
,
959 priv
->hw
->desc
->init_tx_desc(&priv
->dma_tx
[i
],
965 * stmmac_init_rx_buffers - init the RX descriptor buffer.
966 * @priv: driver private structure
967 * @p: descriptor pointer
968 * @i: descriptor index
970 * Description: this function is called to allocate a receive buffer, perform
971 * the DMA mapping and init the descriptor.
973 static int stmmac_init_rx_buffers(struct stmmac_priv
*priv
, struct dma_desc
*p
,
978 skb
= __netdev_alloc_skb(priv
->dev
, priv
->dma_buf_sz
+ NET_IP_ALIGN
,
981 pr_err("%s: Rx init fails; skb is NULL\n", __func__
);
984 skb_reserve(skb
, NET_IP_ALIGN
);
985 priv
->rx_skbuff
[i
] = skb
;
986 priv
->rx_skbuff_dma
[i
] = dma_map_single(priv
->device
, skb
->data
,
989 if (dma_mapping_error(priv
->device
, priv
->rx_skbuff_dma
[i
])) {
990 pr_err("%s: DMA mapping error\n", __func__
);
991 dev_kfree_skb_any(skb
);
995 p
->des2
= priv
->rx_skbuff_dma
[i
];
997 if ((priv
->hw
->mode
->init_desc3
) &&
998 (priv
->dma_buf_sz
== BUF_SIZE_16KiB
))
999 priv
->hw
->mode
->init_desc3(p
);
1004 static void stmmac_free_rx_buffers(struct stmmac_priv
*priv
, int i
)
1006 if (priv
->rx_skbuff
[i
]) {
1007 dma_unmap_single(priv
->device
, priv
->rx_skbuff_dma
[i
],
1008 priv
->dma_buf_sz
, DMA_FROM_DEVICE
);
1009 dev_kfree_skb_any(priv
->rx_skbuff
[i
]);
1011 priv
->rx_skbuff
[i
] = NULL
;
1015 * init_dma_desc_rings - init the RX/TX descriptor rings
1016 * @dev: net device structure
1018 * Description: this function initializes the DMA RX/TX descriptors
1019 * and allocates the socket buffers. It suppors the chained and ring
1022 static int init_dma_desc_rings(struct net_device
*dev
, gfp_t flags
)
1025 struct stmmac_priv
*priv
= netdev_priv(dev
);
1026 unsigned int txsize
= priv
->dma_tx_size
;
1027 unsigned int rxsize
= priv
->dma_rx_size
;
1028 unsigned int bfsize
= 0;
1031 if (priv
->hw
->mode
->set_16kib_bfsize
)
1032 bfsize
= priv
->hw
->mode
->set_16kib_bfsize(dev
->mtu
);
1034 if (bfsize
< BUF_SIZE_16KiB
)
1035 bfsize
= stmmac_set_bfsize(dev
->mtu
, priv
->dma_buf_sz
);
1037 priv
->dma_buf_sz
= bfsize
;
1039 if (netif_msg_probe(priv
))
1040 pr_debug("%s: txsize %d, rxsize %d, bfsize %d\n", __func__
,
1041 txsize
, rxsize
, bfsize
);
1043 if (netif_msg_probe(priv
)) {
1044 pr_debug("(%s) dma_rx_phy=0x%08x dma_tx_phy=0x%08x\n", __func__
,
1045 (u32
) priv
->dma_rx_phy
, (u32
) priv
->dma_tx_phy
);
1047 /* RX INITIALIZATION */
1048 pr_debug("\tSKB addresses:\nskb\t\tskb data\tdma data\n");
1050 for (i
= 0; i
< rxsize
; i
++) {
1052 if (priv
->extend_desc
)
1053 p
= &((priv
->dma_erx
+ i
)->basic
);
1055 p
= priv
->dma_rx
+ i
;
1057 ret
= stmmac_init_rx_buffers(priv
, p
, i
, flags
);
1059 goto err_init_rx_buffers
;
1061 if (netif_msg_probe(priv
))
1062 pr_debug("[%p]\t[%p]\t[%x]\n", priv
->rx_skbuff
[i
],
1063 priv
->rx_skbuff
[i
]->data
,
1064 (unsigned int)priv
->rx_skbuff_dma
[i
]);
1067 priv
->dirty_rx
= (unsigned int)(i
- rxsize
);
1070 /* Setup the chained descriptor addresses */
1071 if (priv
->mode
== STMMAC_CHAIN_MODE
) {
1072 if (priv
->extend_desc
) {
1073 priv
->hw
->mode
->init(priv
->dma_erx
, priv
->dma_rx_phy
,
1075 priv
->hw
->mode
->init(priv
->dma_etx
, priv
->dma_tx_phy
,
1078 priv
->hw
->mode
->init(priv
->dma_rx
, priv
->dma_rx_phy
,
1080 priv
->hw
->mode
->init(priv
->dma_tx
, priv
->dma_tx_phy
,
1085 /* TX INITIALIZATION */
1086 for (i
= 0; i
< txsize
; i
++) {
1088 if (priv
->extend_desc
)
1089 p
= &((priv
->dma_etx
+ i
)->basic
);
1091 p
= priv
->dma_tx
+ i
;
1093 priv
->tx_skbuff_dma
[i
].buf
= 0;
1094 priv
->tx_skbuff_dma
[i
].map_as_page
= false;
1095 priv
->tx_skbuff
[i
] = NULL
;
1100 netdev_reset_queue(priv
->dev
);
1102 stmmac_clear_descriptors(priv
);
1104 if (netif_msg_hw(priv
))
1105 stmmac_display_rings(priv
);
1108 err_init_rx_buffers
:
1110 stmmac_free_rx_buffers(priv
, i
);
1114 static void dma_free_rx_skbufs(struct stmmac_priv
*priv
)
1118 for (i
= 0; i
< priv
->dma_rx_size
; i
++)
1119 stmmac_free_rx_buffers(priv
, i
);
1122 static void dma_free_tx_skbufs(struct stmmac_priv
*priv
)
1126 for (i
= 0; i
< priv
->dma_tx_size
; i
++) {
1129 if (priv
->extend_desc
)
1130 p
= &((priv
->dma_etx
+ i
)->basic
);
1132 p
= priv
->dma_tx
+ i
;
1134 if (priv
->tx_skbuff_dma
[i
].buf
) {
1135 if (priv
->tx_skbuff_dma
[i
].map_as_page
)
1136 dma_unmap_page(priv
->device
,
1137 priv
->tx_skbuff_dma
[i
].buf
,
1138 priv
->hw
->desc
->get_tx_len(p
),
1141 dma_unmap_single(priv
->device
,
1142 priv
->tx_skbuff_dma
[i
].buf
,
1143 priv
->hw
->desc
->get_tx_len(p
),
1147 if (priv
->tx_skbuff
[i
] != NULL
) {
1148 dev_kfree_skb_any(priv
->tx_skbuff
[i
]);
1149 priv
->tx_skbuff
[i
] = NULL
;
1150 priv
->tx_skbuff_dma
[i
].buf
= 0;
1151 priv
->tx_skbuff_dma
[i
].map_as_page
= false;
1157 * alloc_dma_desc_resources - alloc TX/RX resources.
1158 * @priv: private structure
1159 * Description: according to which descriptor can be used (extend or basic)
1160 * this function allocates the resources for TX and RX paths. In case of
1161 * reception, for example, it pre-allocated the RX socket buffer in order to
1162 * allow zero-copy mechanism.
1164 static int alloc_dma_desc_resources(struct stmmac_priv
*priv
)
1166 unsigned int txsize
= priv
->dma_tx_size
;
1167 unsigned int rxsize
= priv
->dma_rx_size
;
1170 priv
->rx_skbuff_dma
= kmalloc_array(rxsize
, sizeof(dma_addr_t
),
1172 if (!priv
->rx_skbuff_dma
)
1175 priv
->rx_skbuff
= kmalloc_array(rxsize
, sizeof(struct sk_buff
*),
1177 if (!priv
->rx_skbuff
)
1180 priv
->tx_skbuff_dma
= kmalloc_array(txsize
,
1181 sizeof(*priv
->tx_skbuff_dma
),
1183 if (!priv
->tx_skbuff_dma
)
1184 goto err_tx_skbuff_dma
;
1186 priv
->tx_skbuff
= kmalloc_array(txsize
, sizeof(struct sk_buff
*),
1188 if (!priv
->tx_skbuff
)
1191 if (priv
->extend_desc
) {
1192 priv
->dma_erx
= dma_alloc_coherent(priv
->device
, rxsize
*
1200 priv
->dma_etx
= dma_alloc_coherent(priv
->device
, txsize
*
1205 if (!priv
->dma_etx
) {
1206 dma_free_coherent(priv
->device
, priv
->dma_rx_size
*
1207 sizeof(struct dma_extended_desc
),
1208 priv
->dma_erx
, priv
->dma_rx_phy
);
1212 priv
->dma_rx
= dma_alloc_coherent(priv
->device
, rxsize
*
1213 sizeof(struct dma_desc
),
1219 priv
->dma_tx
= dma_alloc_coherent(priv
->device
, txsize
*
1220 sizeof(struct dma_desc
),
1223 if (!priv
->dma_tx
) {
1224 dma_free_coherent(priv
->device
, priv
->dma_rx_size
*
1225 sizeof(struct dma_desc
),
1226 priv
->dma_rx
, priv
->dma_rx_phy
);
1234 kfree(priv
->tx_skbuff
);
1236 kfree(priv
->tx_skbuff_dma
);
1238 kfree(priv
->rx_skbuff
);
1240 kfree(priv
->rx_skbuff_dma
);
1244 static void free_dma_desc_resources(struct stmmac_priv
*priv
)
1246 /* Release the DMA TX/RX socket buffers */
1247 dma_free_rx_skbufs(priv
);
1248 dma_free_tx_skbufs(priv
);
1250 /* Free DMA regions of consistent memory previously allocated */
1251 if (!priv
->extend_desc
) {
1252 dma_free_coherent(priv
->device
,
1253 priv
->dma_tx_size
* sizeof(struct dma_desc
),
1254 priv
->dma_tx
, priv
->dma_tx_phy
);
1255 dma_free_coherent(priv
->device
,
1256 priv
->dma_rx_size
* sizeof(struct dma_desc
),
1257 priv
->dma_rx
, priv
->dma_rx_phy
);
1259 dma_free_coherent(priv
->device
, priv
->dma_tx_size
*
1260 sizeof(struct dma_extended_desc
),
1261 priv
->dma_etx
, priv
->dma_tx_phy
);
1262 dma_free_coherent(priv
->device
, priv
->dma_rx_size
*
1263 sizeof(struct dma_extended_desc
),
1264 priv
->dma_erx
, priv
->dma_rx_phy
);
1266 kfree(priv
->rx_skbuff_dma
);
1267 kfree(priv
->rx_skbuff
);
1268 kfree(priv
->tx_skbuff_dma
);
1269 kfree(priv
->tx_skbuff
);
1273 * stmmac_dma_operation_mode - HW DMA operation mode
1274 * @priv: driver private structure
1275 * Description: it is used for configuring the DMA operation mode register in
1276 * order to program the tx/rx DMA thresholds or Store-And-Forward mode.
1278 static void stmmac_dma_operation_mode(struct stmmac_priv
*priv
)
1280 if (priv
->plat
->force_thresh_dma_mode
)
1281 priv
->hw
->dma
->dma_mode(priv
->ioaddr
, tc
, tc
);
1282 else if (priv
->plat
->force_sf_dma_mode
|| priv
->plat
->tx_coe
) {
1284 * In case of GMAC, SF mode can be enabled
1285 * to perform the TX COE in HW. This depends on:
1286 * 1) TX COE if actually supported
1287 * 2) There is no bugged Jumbo frame support
1288 * that needs to not insert csum in the TDES.
1290 priv
->hw
->dma
->dma_mode(priv
->ioaddr
, SF_DMA_MODE
, SF_DMA_MODE
);
1291 priv
->xstats
.threshold
= SF_DMA_MODE
;
1293 priv
->hw
->dma
->dma_mode(priv
->ioaddr
, tc
, SF_DMA_MODE
);
1297 * stmmac_tx_clean - to manage the transmission completion
1298 * @priv: driver private structure
1299 * Description: it reclaims the transmit resources after transmission completes.
1301 static void stmmac_tx_clean(struct stmmac_priv
*priv
)
1303 unsigned int txsize
= priv
->dma_tx_size
;
1304 unsigned int bytes_compl
= 0, pkts_compl
= 0;
1306 spin_lock(&priv
->tx_lock
);
1308 priv
->xstats
.tx_clean
++;
1310 while (priv
->dirty_tx
!= priv
->cur_tx
) {
1312 unsigned int entry
= priv
->dirty_tx
% txsize
;
1313 struct sk_buff
*skb
= priv
->tx_skbuff
[entry
];
1316 if (priv
->extend_desc
)
1317 p
= (struct dma_desc
*)(priv
->dma_etx
+ entry
);
1319 p
= priv
->dma_tx
+ entry
;
1321 /* Check if the descriptor is owned by the DMA. */
1322 if (priv
->hw
->desc
->get_tx_owner(p
))
1325 /* Verify tx error by looking at the last segment. */
1326 last
= priv
->hw
->desc
->get_tx_ls(p
);
1329 priv
->hw
->desc
->tx_status(&priv
->dev
->stats
,
1332 if (likely(tx_error
== 0)) {
1333 priv
->dev
->stats
.tx_packets
++;
1334 priv
->xstats
.tx_pkt_n
++;
1336 priv
->dev
->stats
.tx_errors
++;
1338 stmmac_get_tx_hwtstamp(priv
, entry
, skb
);
1340 if (netif_msg_tx_done(priv
))
1341 pr_debug("%s: curr %d, dirty %d\n", __func__
,
1342 priv
->cur_tx
, priv
->dirty_tx
);
1344 if (likely(priv
->tx_skbuff_dma
[entry
].buf
)) {
1345 if (priv
->tx_skbuff_dma
[entry
].map_as_page
)
1346 dma_unmap_page(priv
->device
,
1347 priv
->tx_skbuff_dma
[entry
].buf
,
1348 priv
->hw
->desc
->get_tx_len(p
),
1351 dma_unmap_single(priv
->device
,
1352 priv
->tx_skbuff_dma
[entry
].buf
,
1353 priv
->hw
->desc
->get_tx_len(p
),
1355 priv
->tx_skbuff_dma
[entry
].buf
= 0;
1356 priv
->tx_skbuff_dma
[entry
].map_as_page
= false;
1358 priv
->hw
->mode
->clean_desc3(priv
, p
);
1360 if (likely(skb
!= NULL
)) {
1362 bytes_compl
+= skb
->len
;
1363 dev_consume_skb_any(skb
);
1364 priv
->tx_skbuff
[entry
] = NULL
;
1367 priv
->hw
->desc
->release_tx_desc(p
, priv
->mode
);
1372 netdev_completed_queue(priv
->dev
, pkts_compl
, bytes_compl
);
1374 if (unlikely(netif_queue_stopped(priv
->dev
) &&
1375 stmmac_tx_avail(priv
) > STMMAC_TX_THRESH(priv
))) {
1376 netif_tx_lock(priv
->dev
);
1377 if (netif_queue_stopped(priv
->dev
) &&
1378 stmmac_tx_avail(priv
) > STMMAC_TX_THRESH(priv
)) {
1379 if (netif_msg_tx_done(priv
))
1380 pr_debug("%s: restart transmit\n", __func__
);
1381 netif_wake_queue(priv
->dev
);
1383 netif_tx_unlock(priv
->dev
);
1386 if ((priv
->eee_enabled
) && (!priv
->tx_path_in_lpi_mode
)) {
1387 stmmac_enable_eee_mode(priv
);
1388 mod_timer(&priv
->eee_ctrl_timer
, STMMAC_LPI_T(eee_timer
));
1390 spin_unlock(&priv
->tx_lock
);
1393 static inline void stmmac_enable_dma_irq(struct stmmac_priv
*priv
)
1395 priv
->hw
->dma
->enable_dma_irq(priv
->ioaddr
);
1398 static inline void stmmac_disable_dma_irq(struct stmmac_priv
*priv
)
1400 priv
->hw
->dma
->disable_dma_irq(priv
->ioaddr
);
1404 * stmmac_tx_err - to manage the tx error
1405 * @priv: driver private structure
1406 * Description: it cleans the descriptors and restarts the transmission
1407 * in case of transmission errors.
1409 static void stmmac_tx_err(struct stmmac_priv
*priv
)
1412 int txsize
= priv
->dma_tx_size
;
1413 netif_stop_queue(priv
->dev
);
1415 priv
->hw
->dma
->stop_tx(priv
->ioaddr
);
1416 dma_free_tx_skbufs(priv
);
1417 for (i
= 0; i
< txsize
; i
++)
1418 if (priv
->extend_desc
)
1419 priv
->hw
->desc
->init_tx_desc(&priv
->dma_etx
[i
].basic
,
1423 priv
->hw
->desc
->init_tx_desc(&priv
->dma_tx
[i
],
1428 netdev_reset_queue(priv
->dev
);
1429 priv
->hw
->dma
->start_tx(priv
->ioaddr
);
1431 priv
->dev
->stats
.tx_errors
++;
1432 netif_wake_queue(priv
->dev
);
1436 * stmmac_dma_interrupt - DMA ISR
1437 * @priv: driver private structure
1438 * Description: this is the DMA ISR. It is called by the main ISR.
1439 * It calls the dwmac dma routine and schedule poll method in case of some
1442 static void stmmac_dma_interrupt(struct stmmac_priv
*priv
)
1446 status
= priv
->hw
->dma
->dma_interrupt(priv
->ioaddr
, &priv
->xstats
);
1447 if (likely((status
& handle_rx
)) || (status
& handle_tx
)) {
1448 if (likely(napi_schedule_prep(&priv
->napi
))) {
1449 stmmac_disable_dma_irq(priv
);
1450 __napi_schedule(&priv
->napi
);
1453 if (unlikely(status
& tx_hard_error_bump_tc
)) {
1454 /* Try to bump up the dma threshold on this failure */
1455 if (unlikely(priv
->xstats
.threshold
!= SF_DMA_MODE
) &&
1458 if (priv
->plat
->force_thresh_dma_mode
)
1459 priv
->hw
->dma
->dma_mode(priv
->ioaddr
, tc
, tc
);
1461 priv
->hw
->dma
->dma_mode(priv
->ioaddr
, tc
,
1463 priv
->xstats
.threshold
= tc
;
1465 } else if (unlikely(status
== tx_hard_error
))
1466 stmmac_tx_err(priv
);
1470 * stmmac_mmc_setup: setup the Mac Management Counters (MMC)
1471 * @priv: driver private structure
1472 * Description: this masks the MMC irq, in fact, the counters are managed in SW.
1474 static void stmmac_mmc_setup(struct stmmac_priv
*priv
)
1476 unsigned int mode
= MMC_CNTRL_RESET_ON_READ
| MMC_CNTRL_COUNTER_RESET
|
1477 MMC_CNTRL_PRESET
| MMC_CNTRL_FULL_HALF_PRESET
;
1479 dwmac_mmc_intr_all_mask(priv
->ioaddr
);
1481 if (priv
->dma_cap
.rmon
) {
1482 dwmac_mmc_ctrl(priv
->ioaddr
, mode
);
1483 memset(&priv
->mmc
, 0, sizeof(struct stmmac_counters
));
1485 pr_info(" No MAC Management Counters available\n");
1489 * stmmac_get_synopsys_id - return the SYINID.
1490 * @priv: driver private structure
1491 * Description: this simple function is to decode and return the SYINID
1492 * starting from the HW core register.
1494 static u32
stmmac_get_synopsys_id(struct stmmac_priv
*priv
)
1496 u32 hwid
= priv
->hw
->synopsys_uid
;
1498 /* Check Synopsys Id (not available on old chips) */
1500 u32 uid
= ((hwid
& 0x0000ff00) >> 8);
1501 u32 synid
= (hwid
& 0x000000ff);
1503 pr_info("stmmac - user ID: 0x%x, Synopsys ID: 0x%x\n",
1512 * stmmac_selec_desc_mode - to select among: normal/alternate/extend descriptors
1513 * @priv: driver private structure
1514 * Description: select the Enhanced/Alternate or Normal descriptors.
1515 * In case of Enhanced/Alternate, it checks if the extended descriptors are
1516 * supported by the HW capability register.
1518 static void stmmac_selec_desc_mode(struct stmmac_priv
*priv
)
1520 if (priv
->plat
->enh_desc
) {
1521 pr_info(" Enhanced/Alternate descriptors\n");
1523 /* GMAC older than 3.50 has no extended descriptors */
1524 if (priv
->synopsys_id
>= DWMAC_CORE_3_50
) {
1525 pr_info("\tEnabled extended descriptors\n");
1526 priv
->extend_desc
= 1;
1528 pr_warn("Extended descriptors not supported\n");
1530 priv
->hw
->desc
= &enh_desc_ops
;
1532 pr_info(" Normal descriptors\n");
1533 priv
->hw
->desc
= &ndesc_ops
;
1538 * stmmac_get_hw_features - get MAC capabilities from the HW cap. register.
1539 * @priv: driver private structure
1541 * new GMAC chip generations have a new register to indicate the
1542 * presence of the optional feature/functions.
1543 * This can be also used to override the value passed through the
1544 * platform and necessary for old MAC10/100 and GMAC chips.
1546 static int stmmac_get_hw_features(struct stmmac_priv
*priv
)
1550 if (priv
->hw
->dma
->get_hw_feature
) {
1551 hw_cap
= priv
->hw
->dma
->get_hw_feature(priv
->ioaddr
);
1553 priv
->dma_cap
.mbps_10_100
= (hw_cap
& DMA_HW_FEAT_MIISEL
);
1554 priv
->dma_cap
.mbps_1000
= (hw_cap
& DMA_HW_FEAT_GMIISEL
) >> 1;
1555 priv
->dma_cap
.half_duplex
= (hw_cap
& DMA_HW_FEAT_HDSEL
) >> 2;
1556 priv
->dma_cap
.hash_filter
= (hw_cap
& DMA_HW_FEAT_HASHSEL
) >> 4;
1557 priv
->dma_cap
.multi_addr
= (hw_cap
& DMA_HW_FEAT_ADDMAC
) >> 5;
1558 priv
->dma_cap
.pcs
= (hw_cap
& DMA_HW_FEAT_PCSSEL
) >> 6;
1559 priv
->dma_cap
.sma_mdio
= (hw_cap
& DMA_HW_FEAT_SMASEL
) >> 8;
1560 priv
->dma_cap
.pmt_remote_wake_up
=
1561 (hw_cap
& DMA_HW_FEAT_RWKSEL
) >> 9;
1562 priv
->dma_cap
.pmt_magic_frame
=
1563 (hw_cap
& DMA_HW_FEAT_MGKSEL
) >> 10;
1565 priv
->dma_cap
.rmon
= (hw_cap
& DMA_HW_FEAT_MMCSEL
) >> 11;
1566 /* IEEE 1588-2002 */
1567 priv
->dma_cap
.time_stamp
=
1568 (hw_cap
& DMA_HW_FEAT_TSVER1SEL
) >> 12;
1569 /* IEEE 1588-2008 */
1570 priv
->dma_cap
.atime_stamp
=
1571 (hw_cap
& DMA_HW_FEAT_TSVER2SEL
) >> 13;
1572 /* 802.3az - Energy-Efficient Ethernet (EEE) */
1573 priv
->dma_cap
.eee
= (hw_cap
& DMA_HW_FEAT_EEESEL
) >> 14;
1574 priv
->dma_cap
.av
= (hw_cap
& DMA_HW_FEAT_AVSEL
) >> 15;
1575 /* TX and RX csum */
1576 priv
->dma_cap
.tx_coe
= (hw_cap
& DMA_HW_FEAT_TXCOESEL
) >> 16;
1577 priv
->dma_cap
.rx_coe_type1
=
1578 (hw_cap
& DMA_HW_FEAT_RXTYP1COE
) >> 17;
1579 priv
->dma_cap
.rx_coe_type2
=
1580 (hw_cap
& DMA_HW_FEAT_RXTYP2COE
) >> 18;
1581 priv
->dma_cap
.rxfifo_over_2048
=
1582 (hw_cap
& DMA_HW_FEAT_RXFIFOSIZE
) >> 19;
1583 /* TX and RX number of channels */
1584 priv
->dma_cap
.number_rx_channel
=
1585 (hw_cap
& DMA_HW_FEAT_RXCHCNT
) >> 20;
1586 priv
->dma_cap
.number_tx_channel
=
1587 (hw_cap
& DMA_HW_FEAT_TXCHCNT
) >> 22;
1588 /* Alternate (enhanced) DESC mode */
1589 priv
->dma_cap
.enh_desc
= (hw_cap
& DMA_HW_FEAT_ENHDESSEL
) >> 24;
1596 * stmmac_check_ether_addr - check if the MAC addr is valid
1597 * @priv: driver private structure
1599 * it is to verify if the MAC address is valid, in case of failures it
1600 * generates a random MAC address
1602 static void stmmac_check_ether_addr(struct stmmac_priv
*priv
)
1604 if (!is_valid_ether_addr(priv
->dev
->dev_addr
)) {
1605 priv
->hw
->mac
->get_umac_addr(priv
->hw
,
1606 priv
->dev
->dev_addr
, 0);
1607 if (!is_valid_ether_addr(priv
->dev
->dev_addr
))
1608 eth_hw_addr_random(priv
->dev
);
1609 pr_info("%s: device MAC address %pM\n", priv
->dev
->name
,
1610 priv
->dev
->dev_addr
);
1615 * stmmac_init_dma_engine - DMA init.
1616 * @priv: driver private structure
1618 * It inits the DMA invoking the specific MAC/GMAC callback.
1619 * Some DMA parameters can be passed from the platform;
1620 * in case of these are not passed a default is kept for the MAC or GMAC.
1622 static int stmmac_init_dma_engine(struct stmmac_priv
*priv
)
1624 int pbl
= DEFAULT_DMA_PBL
, fixed_burst
= 0, burst_len
= 0;
1625 int mixed_burst
= 0;
1628 if (priv
->plat
->dma_cfg
) {
1629 pbl
= priv
->plat
->dma_cfg
->pbl
;
1630 fixed_burst
= priv
->plat
->dma_cfg
->fixed_burst
;
1631 mixed_burst
= priv
->plat
->dma_cfg
->mixed_burst
;
1632 burst_len
= priv
->plat
->dma_cfg
->burst_len
;
1635 if (priv
->extend_desc
&& (priv
->mode
== STMMAC_RING_MODE
))
1638 return priv
->hw
->dma
->init(priv
->ioaddr
, pbl
, fixed_burst
, mixed_burst
,
1639 burst_len
, priv
->dma_tx_phy
,
1640 priv
->dma_rx_phy
, atds
);
1644 * stmmac_tx_timer - mitigation sw timer for tx.
1645 * @data: data pointer
1647 * This is the timer handler to directly invoke the stmmac_tx_clean.
1649 static void stmmac_tx_timer(unsigned long data
)
1651 struct stmmac_priv
*priv
= (struct stmmac_priv
*)data
;
1653 stmmac_tx_clean(priv
);
1657 * stmmac_init_tx_coalesce - init tx mitigation options.
1658 * @priv: driver private structure
1660 * This inits the transmit coalesce parameters: i.e. timer rate,
1661 * timer handler and default threshold used for enabling the
1662 * interrupt on completion bit.
1664 static void stmmac_init_tx_coalesce(struct stmmac_priv
*priv
)
1666 priv
->tx_coal_frames
= STMMAC_TX_FRAMES
;
1667 priv
->tx_coal_timer
= STMMAC_COAL_TX_TIMER
;
1668 init_timer(&priv
->txtimer
);
1669 priv
->txtimer
.expires
= STMMAC_COAL_TIMER(priv
->tx_coal_timer
);
1670 priv
->txtimer
.data
= (unsigned long)priv
;
1671 priv
->txtimer
.function
= stmmac_tx_timer
;
1672 add_timer(&priv
->txtimer
);
1676 * stmmac_hw_setup - setup mac in a usable state.
1677 * @dev : pointer to the device structure.
1679 * this is the main function to setup the HW in a usable state because the
1680 * dma engine is reset, the core registers are configured (e.g. AXI,
1681 * Checksum features, timers). The DMA is ready to start receiving and
1684 * 0 on success and an appropriate (-)ve integer as defined in errno.h
1687 static int stmmac_hw_setup(struct net_device
*dev
, bool init_ptp
)
1689 struct stmmac_priv
*priv
= netdev_priv(dev
);
1692 /* DMA initialization and SW reset */
1693 ret
= stmmac_init_dma_engine(priv
);
1695 pr_err("%s: DMA engine initialization failed\n", __func__
);
1699 /* Copy the MAC addr into the HW */
1700 priv
->hw
->mac
->set_umac_addr(priv
->hw
, dev
->dev_addr
, 0);
1702 /* If required, perform hw setup of the bus. */
1703 if (priv
->plat
->bus_setup
)
1704 priv
->plat
->bus_setup(priv
->ioaddr
);
1706 /* Initialize the MAC Core */
1707 priv
->hw
->mac
->core_init(priv
->hw
, dev
->mtu
);
1709 ret
= priv
->hw
->mac
->rx_ipc(priv
->hw
);
1711 pr_warn(" RX IPC Checksum Offload disabled\n");
1712 priv
->plat
->rx_coe
= STMMAC_RX_COE_NONE
;
1713 priv
->hw
->rx_csum
= 0;
1716 /* Enable the MAC Rx/Tx */
1717 stmmac_set_mac(priv
->ioaddr
, true);
1719 /* Set the HW DMA mode and the COE */
1720 stmmac_dma_operation_mode(priv
);
1722 stmmac_mmc_setup(priv
);
1725 ret
= stmmac_init_ptp(priv
);
1726 if (ret
&& ret
!= -EOPNOTSUPP
)
1727 pr_warn("%s: failed PTP initialisation\n", __func__
);
1730 #ifdef CONFIG_DEBUG_FS
1731 ret
= stmmac_init_fs(dev
);
1733 pr_warn("%s: failed debugFS registration\n", __func__
);
1735 /* Start the ball rolling... */
1736 pr_debug("%s: DMA RX/TX processes started...\n", dev
->name
);
1737 priv
->hw
->dma
->start_tx(priv
->ioaddr
);
1738 priv
->hw
->dma
->start_rx(priv
->ioaddr
);
1740 /* Dump DMA/MAC registers */
1741 if (netif_msg_hw(priv
)) {
1742 priv
->hw
->mac
->dump_regs(priv
->hw
);
1743 priv
->hw
->dma
->dump_regs(priv
->ioaddr
);
1745 priv
->tx_lpi_timer
= STMMAC_DEFAULT_TWT_LS
;
1747 if ((priv
->use_riwt
) && (priv
->hw
->dma
->rx_watchdog
)) {
1748 priv
->rx_riwt
= MAX_DMA_RIWT
;
1749 priv
->hw
->dma
->rx_watchdog(priv
->ioaddr
, MAX_DMA_RIWT
);
1752 if (priv
->pcs
&& priv
->hw
->mac
->ctrl_ane
)
1753 priv
->hw
->mac
->ctrl_ane(priv
->hw
, 0);
1759 * stmmac_open - open entry point of the driver
1760 * @dev : pointer to the device structure.
1762 * This function is the open entry point of the driver.
1764 * 0 on success and an appropriate (-)ve integer as defined in errno.h
1767 static int stmmac_open(struct net_device
*dev
)
1769 struct stmmac_priv
*priv
= netdev_priv(dev
);
1772 stmmac_check_ether_addr(priv
);
1774 if (priv
->pcs
!= STMMAC_PCS_RGMII
&& priv
->pcs
!= STMMAC_PCS_TBI
&&
1775 priv
->pcs
!= STMMAC_PCS_RTBI
) {
1776 ret
= stmmac_init_phy(dev
);
1778 pr_err("%s: Cannot attach to PHY (error: %d)\n",
1784 /* Extra statistics */
1785 memset(&priv
->xstats
, 0, sizeof(struct stmmac_extra_stats
));
1786 priv
->xstats
.threshold
= tc
;
1788 /* Create and initialize the TX/RX descriptors chains. */
1789 priv
->dma_tx_size
= STMMAC_ALIGN(dma_txsize
);
1790 priv
->dma_rx_size
= STMMAC_ALIGN(dma_rxsize
);
1791 priv
->dma_buf_sz
= STMMAC_ALIGN(buf_sz
);
1793 ret
= alloc_dma_desc_resources(priv
);
1795 pr_err("%s: DMA descriptors allocation failed\n", __func__
);
1796 goto dma_desc_error
;
1799 ret
= init_dma_desc_rings(dev
, GFP_KERNEL
);
1801 pr_err("%s: DMA descriptors initialization failed\n", __func__
);
1805 ret
= stmmac_hw_setup(dev
, true);
1807 pr_err("%s: Hw setup failed\n", __func__
);
1811 stmmac_init_tx_coalesce(priv
);
1814 phy_start(priv
->phydev
);
1816 /* Request the IRQ lines */
1817 ret
= request_irq(dev
->irq
, stmmac_interrupt
,
1818 IRQF_SHARED
, dev
->name
, dev
);
1819 if (unlikely(ret
< 0)) {
1820 pr_err("%s: ERROR: allocating the IRQ %d (error: %d)\n",
1821 __func__
, dev
->irq
, ret
);
1825 /* Request the Wake IRQ in case of another line is used for WoL */
1826 if (priv
->wol_irq
!= dev
->irq
) {
1827 ret
= request_irq(priv
->wol_irq
, stmmac_interrupt
,
1828 IRQF_SHARED
, dev
->name
, dev
);
1829 if (unlikely(ret
< 0)) {
1830 pr_err("%s: ERROR: allocating the WoL IRQ %d (%d)\n",
1831 __func__
, priv
->wol_irq
, ret
);
1836 /* Request the IRQ lines */
1837 if (priv
->lpi_irq
> 0) {
1838 ret
= request_irq(priv
->lpi_irq
, stmmac_interrupt
, IRQF_SHARED
,
1840 if (unlikely(ret
< 0)) {
1841 pr_err("%s: ERROR: allocating the LPI IRQ %d (%d)\n",
1842 __func__
, priv
->lpi_irq
, ret
);
1847 napi_enable(&priv
->napi
);
1848 netif_start_queue(dev
);
1853 if (priv
->wol_irq
!= dev
->irq
)
1854 free_irq(priv
->wol_irq
, dev
);
1856 free_irq(dev
->irq
, dev
);
1859 free_dma_desc_resources(priv
);
1862 phy_disconnect(priv
->phydev
);
1868 * stmmac_release - close entry point of the driver
1869 * @dev : device pointer.
1871 * This is the stop entry point of the driver.
1873 static int stmmac_release(struct net_device
*dev
)
1875 struct stmmac_priv
*priv
= netdev_priv(dev
);
1877 if (priv
->eee_enabled
)
1878 del_timer_sync(&priv
->eee_ctrl_timer
);
1880 /* Stop and disconnect the PHY */
1882 phy_stop(priv
->phydev
);
1883 phy_disconnect(priv
->phydev
);
1884 priv
->phydev
= NULL
;
1887 netif_stop_queue(dev
);
1889 napi_disable(&priv
->napi
);
1891 del_timer_sync(&priv
->txtimer
);
1893 /* Free the IRQ lines */
1894 free_irq(dev
->irq
, dev
);
1895 if (priv
->wol_irq
!= dev
->irq
)
1896 free_irq(priv
->wol_irq
, dev
);
1897 if (priv
->lpi_irq
> 0)
1898 free_irq(priv
->lpi_irq
, dev
);
1900 /* Stop TX/RX DMA and clear the descriptors */
1901 priv
->hw
->dma
->stop_tx(priv
->ioaddr
);
1902 priv
->hw
->dma
->stop_rx(priv
->ioaddr
);
1904 /* Release and free the Rx/Tx resources */
1905 free_dma_desc_resources(priv
);
1907 /* Disable the MAC Rx/Tx */
1908 stmmac_set_mac(priv
->ioaddr
, false);
1910 netif_carrier_off(dev
);
1912 #ifdef CONFIG_DEBUG_FS
1916 stmmac_release_ptp(priv
);
1922 * stmmac_xmit - Tx entry point of the driver
1923 * @skb : the socket buffer
1924 * @dev : device pointer
1925 * Description : this is the tx entry point of the driver.
1926 * It programs the chain or the ring and supports oversized frames
1929 static netdev_tx_t
stmmac_xmit(struct sk_buff
*skb
, struct net_device
*dev
)
1931 struct stmmac_priv
*priv
= netdev_priv(dev
);
1932 unsigned int txsize
= priv
->dma_tx_size
;
1934 int i
, csum_insertion
= 0, is_jumbo
= 0;
1935 int nfrags
= skb_shinfo(skb
)->nr_frags
;
1936 struct dma_desc
*desc
, *first
;
1937 unsigned int nopaged_len
= skb_headlen(skb
);
1938 unsigned int enh_desc
= priv
->plat
->enh_desc
;
1940 spin_lock(&priv
->tx_lock
);
1942 if (unlikely(stmmac_tx_avail(priv
) < nfrags
+ 1)) {
1943 spin_unlock(&priv
->tx_lock
);
1944 if (!netif_queue_stopped(dev
)) {
1945 netif_stop_queue(dev
);
1946 /* This is a hard error, log it. */
1947 pr_err("%s: Tx Ring full when queue awake\n", __func__
);
1949 return NETDEV_TX_BUSY
;
1952 if (priv
->tx_path_in_lpi_mode
)
1953 stmmac_disable_eee_mode(priv
);
1955 entry
= priv
->cur_tx
% txsize
;
1957 csum_insertion
= (skb
->ip_summed
== CHECKSUM_PARTIAL
);
1959 if (priv
->extend_desc
)
1960 desc
= (struct dma_desc
*)(priv
->dma_etx
+ entry
);
1962 desc
= priv
->dma_tx
+ entry
;
1966 /* To program the descriptors according to the size of the frame */
1968 is_jumbo
= priv
->hw
->mode
->is_jumbo_frm(skb
->len
, enh_desc
);
1970 if (likely(!is_jumbo
)) {
1971 desc
->des2
= dma_map_single(priv
->device
, skb
->data
,
1972 nopaged_len
, DMA_TO_DEVICE
);
1973 if (dma_mapping_error(priv
->device
, desc
->des2
))
1975 priv
->tx_skbuff_dma
[entry
].buf
= desc
->des2
;
1976 priv
->hw
->desc
->prepare_tx_desc(desc
, 1, nopaged_len
,
1977 csum_insertion
, priv
->mode
);
1980 entry
= priv
->hw
->mode
->jumbo_frm(priv
, skb
, csum_insertion
);
1981 if (unlikely(entry
< 0))
1985 for (i
= 0; i
< nfrags
; i
++) {
1986 const skb_frag_t
*frag
= &skb_shinfo(skb
)->frags
[i
];
1987 int len
= skb_frag_size(frag
);
1989 priv
->tx_skbuff
[entry
] = NULL
;
1990 entry
= (++priv
->cur_tx
) % txsize
;
1991 if (priv
->extend_desc
)
1992 desc
= (struct dma_desc
*)(priv
->dma_etx
+ entry
);
1994 desc
= priv
->dma_tx
+ entry
;
1996 desc
->des2
= skb_frag_dma_map(priv
->device
, frag
, 0, len
,
1998 if (dma_mapping_error(priv
->device
, desc
->des2
))
1999 goto dma_map_err
; /* should reuse desc w/o issues */
2001 priv
->tx_skbuff_dma
[entry
].buf
= desc
->des2
;
2002 priv
->tx_skbuff_dma
[entry
].map_as_page
= true;
2003 priv
->hw
->desc
->prepare_tx_desc(desc
, 0, len
, csum_insertion
,
2006 priv
->hw
->desc
->set_tx_owner(desc
);
2010 priv
->tx_skbuff
[entry
] = skb
;
2012 /* Finalize the latest segment. */
2013 priv
->hw
->desc
->close_tx_desc(desc
);
2016 /* According to the coalesce parameter the IC bit for the latest
2017 * segment could be reset and the timer re-started to invoke the
2018 * stmmac_tx function. This approach takes care about the fragments.
2020 priv
->tx_count_frames
+= nfrags
+ 1;
2021 if (priv
->tx_coal_frames
> priv
->tx_count_frames
) {
2022 priv
->hw
->desc
->clear_tx_ic(desc
);
2023 priv
->xstats
.tx_reset_ic_bit
++;
2024 mod_timer(&priv
->txtimer
,
2025 STMMAC_COAL_TIMER(priv
->tx_coal_timer
));
2027 priv
->tx_count_frames
= 0;
2029 /* To avoid raise condition */
2030 priv
->hw
->desc
->set_tx_owner(first
);
2035 if (netif_msg_pktdata(priv
)) {
2036 pr_debug("%s: curr %d dirty=%d entry=%d, first=%p, nfrags=%d",
2037 __func__
, (priv
->cur_tx
% txsize
),
2038 (priv
->dirty_tx
% txsize
), entry
, first
, nfrags
);
2040 if (priv
->extend_desc
)
2041 stmmac_display_ring((void *)priv
->dma_etx
, txsize
, 1);
2043 stmmac_display_ring((void *)priv
->dma_tx
, txsize
, 0);
2045 pr_debug(">>> frame to be transmitted: ");
2046 print_pkt(skb
->data
, skb
->len
);
2048 if (unlikely(stmmac_tx_avail(priv
) <= (MAX_SKB_FRAGS
+ 1))) {
2049 if (netif_msg_hw(priv
))
2050 pr_debug("%s: stop transmitted packets\n", __func__
);
2051 netif_stop_queue(dev
);
2054 dev
->stats
.tx_bytes
+= skb
->len
;
2056 if (unlikely((skb_shinfo(skb
)->tx_flags
& SKBTX_HW_TSTAMP
) &&
2057 priv
->hwts_tx_en
)) {
2058 /* declare that device is doing timestamping */
2059 skb_shinfo(skb
)->tx_flags
|= SKBTX_IN_PROGRESS
;
2060 priv
->hw
->desc
->enable_tx_timestamp(first
);
2063 if (!priv
->hwts_tx_en
)
2064 skb_tx_timestamp(skb
);
2066 netdev_sent_queue(dev
, skb
->len
);
2067 priv
->hw
->dma
->enable_dma_transmission(priv
->ioaddr
);
2069 spin_unlock(&priv
->tx_lock
);
2070 return NETDEV_TX_OK
;
2073 spin_unlock(&priv
->tx_lock
);
2074 dev_err(priv
->device
, "Tx dma map failed\n");
2076 priv
->dev
->stats
.tx_dropped
++;
2077 return NETDEV_TX_OK
;
2080 static void stmmac_rx_vlan(struct net_device
*dev
, struct sk_buff
*skb
)
2082 struct ethhdr
*ehdr
;
2085 if ((dev
->features
& NETIF_F_HW_VLAN_CTAG_RX
) ==
2086 NETIF_F_HW_VLAN_CTAG_RX
&&
2087 !__vlan_get_tag(skb
, &vlanid
)) {
2088 /* pop the vlan tag */
2089 ehdr
= (struct ethhdr
*)skb
->data
;
2090 memmove(skb
->data
+ VLAN_HLEN
, ehdr
, ETH_ALEN
* 2);
2091 skb_pull(skb
, VLAN_HLEN
);
2092 __vlan_hwaccel_put_tag(skb
, htons(ETH_P_8021Q
), vlanid
);
2098 * stmmac_rx_refill - refill used skb preallocated buffers
2099 * @priv: driver private structure
2100 * Description : this is to reallocate the skb for the reception process
2101 * that is based on zero-copy.
2103 static inline void stmmac_rx_refill(struct stmmac_priv
*priv
)
2105 unsigned int rxsize
= priv
->dma_rx_size
;
2106 int bfsize
= priv
->dma_buf_sz
;
2108 for (; priv
->cur_rx
- priv
->dirty_rx
> 0; priv
->dirty_rx
++) {
2109 unsigned int entry
= priv
->dirty_rx
% rxsize
;
2112 if (priv
->extend_desc
)
2113 p
= (struct dma_desc
*)(priv
->dma_erx
+ entry
);
2115 p
= priv
->dma_rx
+ entry
;
2117 if (likely(priv
->rx_skbuff
[entry
] == NULL
)) {
2118 struct sk_buff
*skb
;
2120 skb
= netdev_alloc_skb_ip_align(priv
->dev
, bfsize
);
2122 if (unlikely(skb
== NULL
))
2125 priv
->rx_skbuff
[entry
] = skb
;
2126 priv
->rx_skbuff_dma
[entry
] =
2127 dma_map_single(priv
->device
, skb
->data
, bfsize
,
2129 if (dma_mapping_error(priv
->device
,
2130 priv
->rx_skbuff_dma
[entry
])) {
2131 dev_err(priv
->device
, "Rx dma map failed\n");
2135 p
->des2
= priv
->rx_skbuff_dma
[entry
];
2137 priv
->hw
->mode
->refill_desc3(priv
, p
);
2139 if (netif_msg_rx_status(priv
))
2140 pr_debug("\trefill entry #%d\n", entry
);
2143 priv
->hw
->desc
->set_rx_owner(p
);
2149 * stmmac_rx - manage the receive process
2150 * @priv: driver private structure
2151 * @limit: napi bugget.
2152 * Description : this the function called by the napi poll method.
2153 * It gets all the frames inside the ring.
2155 static int stmmac_rx(struct stmmac_priv
*priv
, int limit
)
2157 unsigned int rxsize
= priv
->dma_rx_size
;
2158 unsigned int entry
= priv
->cur_rx
% rxsize
;
2159 unsigned int next_entry
;
2160 unsigned int count
= 0;
2161 int coe
= priv
->hw
->rx_csum
;
2163 if (netif_msg_rx_status(priv
)) {
2164 pr_debug("%s: descriptor ring:\n", __func__
);
2165 if (priv
->extend_desc
)
2166 stmmac_display_ring((void *)priv
->dma_erx
, rxsize
, 1);
2168 stmmac_display_ring((void *)priv
->dma_rx
, rxsize
, 0);
2170 while (count
< limit
) {
2174 if (priv
->extend_desc
)
2175 p
= (struct dma_desc
*)(priv
->dma_erx
+ entry
);
2177 p
= priv
->dma_rx
+ entry
;
2179 if (priv
->hw
->desc
->get_rx_owner(p
))
2184 next_entry
= (++priv
->cur_rx
) % rxsize
;
2185 if (priv
->extend_desc
)
2186 prefetch(priv
->dma_erx
+ next_entry
);
2188 prefetch(priv
->dma_rx
+ next_entry
);
2190 /* read the status of the incoming frame */
2191 status
= priv
->hw
->desc
->rx_status(&priv
->dev
->stats
,
2193 if ((priv
->extend_desc
) && (priv
->hw
->desc
->rx_extended_status
))
2194 priv
->hw
->desc
->rx_extended_status(&priv
->dev
->stats
,
2198 if (unlikely(status
== discard_frame
)) {
2199 priv
->dev
->stats
.rx_errors
++;
2200 if (priv
->hwts_rx_en
&& !priv
->extend_desc
) {
2201 /* DESC2 & DESC3 will be overwitten by device
2202 * with timestamp value, hence reinitialize
2203 * them in stmmac_rx_refill() function so that
2204 * device can reuse it.
2206 priv
->rx_skbuff
[entry
] = NULL
;
2207 dma_unmap_single(priv
->device
,
2208 priv
->rx_skbuff_dma
[entry
],
2213 struct sk_buff
*skb
;
2216 frame_len
= priv
->hw
->desc
->get_rx_frame_len(p
, coe
);
2218 /* ACS is set; GMAC core strips PAD/FCS for IEEE 802.3
2219 * Type frames (LLC/LLC-SNAP)
2221 if (unlikely(status
!= llc_snap
))
2222 frame_len
-= ETH_FCS_LEN
;
2224 if (netif_msg_rx_status(priv
)) {
2225 pr_debug("\tdesc: %p [entry %d] buff=0x%x\n",
2227 if (frame_len
> ETH_FRAME_LEN
)
2228 pr_debug("\tframe size %d, COE: %d\n",
2231 skb
= priv
->rx_skbuff
[entry
];
2232 if (unlikely(!skb
)) {
2233 pr_err("%s: Inconsistent Rx descriptor chain\n",
2235 priv
->dev
->stats
.rx_dropped
++;
2238 prefetch(skb
->data
- NET_IP_ALIGN
);
2239 priv
->rx_skbuff
[entry
] = NULL
;
2241 stmmac_get_rx_hwtstamp(priv
, entry
, skb
);
2243 skb_put(skb
, frame_len
);
2244 dma_unmap_single(priv
->device
,
2245 priv
->rx_skbuff_dma
[entry
],
2246 priv
->dma_buf_sz
, DMA_FROM_DEVICE
);
2248 if (netif_msg_pktdata(priv
)) {
2249 pr_debug("frame received (%dbytes)", frame_len
);
2250 print_pkt(skb
->data
, frame_len
);
2253 stmmac_rx_vlan(priv
->dev
, skb
);
2255 skb
->protocol
= eth_type_trans(skb
, priv
->dev
);
2258 skb_checksum_none_assert(skb
);
2260 skb
->ip_summed
= CHECKSUM_UNNECESSARY
;
2262 napi_gro_receive(&priv
->napi
, skb
);
2264 priv
->dev
->stats
.rx_packets
++;
2265 priv
->dev
->stats
.rx_bytes
+= frame_len
;
2270 stmmac_rx_refill(priv
);
2272 priv
->xstats
.rx_pkt_n
+= count
;
2278 * stmmac_poll - stmmac poll method (NAPI)
2279 * @napi : pointer to the napi structure.
2280 * @budget : maximum number of packets that the current CPU can receive from
2283 * To look at the incoming frames and clear the tx resources.
2285 static int stmmac_poll(struct napi_struct
*napi
, int budget
)
2287 struct stmmac_priv
*priv
= container_of(napi
, struct stmmac_priv
, napi
);
2290 priv
->xstats
.napi_poll
++;
2291 stmmac_tx_clean(priv
);
2293 work_done
= stmmac_rx(priv
, budget
);
2294 if (work_done
< budget
) {
2295 napi_complete(napi
);
2296 stmmac_enable_dma_irq(priv
);
2303 * @dev : Pointer to net device structure
2304 * Description: this function is called when a packet transmission fails to
2305 * complete within a reasonable time. The driver will mark the error in the
2306 * netdev structure and arrange for the device to be reset to a sane state
2307 * in order to transmit a new packet.
2309 static void stmmac_tx_timeout(struct net_device
*dev
)
2311 struct stmmac_priv
*priv
= netdev_priv(dev
);
2313 /* Clear Tx resources and restart transmitting again */
2314 stmmac_tx_err(priv
);
2318 * stmmac_set_rx_mode - entry point for multicast addressing
2319 * @dev : pointer to the device structure
2321 * This function is a driver entry point which gets called by the kernel
2322 * whenever multicast addresses must be enabled/disabled.
2326 static void stmmac_set_rx_mode(struct net_device
*dev
)
2328 struct stmmac_priv
*priv
= netdev_priv(dev
);
2330 priv
->hw
->mac
->set_filter(priv
->hw
, dev
);
2334 * stmmac_change_mtu - entry point to change MTU size for the device.
2335 * @dev : device pointer.
2336 * @new_mtu : the new MTU size for the device.
2337 * Description: the Maximum Transfer Unit (MTU) is used by the network layer
2338 * to drive packet transmission. Ethernet has an MTU of 1500 octets
2339 * (ETH_DATA_LEN). This value can be changed with ifconfig.
2341 * 0 on success and an appropriate (-)ve integer as defined in errno.h
2344 static int stmmac_change_mtu(struct net_device
*dev
, int new_mtu
)
2346 struct stmmac_priv
*priv
= netdev_priv(dev
);
2349 if (netif_running(dev
)) {
2350 pr_err("%s: must be stopped to change its MTU\n", dev
->name
);
2354 if (priv
->plat
->enh_desc
)
2355 max_mtu
= JUMBO_LEN
;
2357 max_mtu
= SKB_MAX_HEAD(NET_SKB_PAD
+ NET_IP_ALIGN
);
2359 if (priv
->plat
->maxmtu
< max_mtu
)
2360 max_mtu
= priv
->plat
->maxmtu
;
2362 if ((new_mtu
< 46) || (new_mtu
> max_mtu
)) {
2363 pr_err("%s: invalid MTU, max MTU is: %d\n", dev
->name
, max_mtu
);
2368 netdev_update_features(dev
);
2373 static netdev_features_t
stmmac_fix_features(struct net_device
*dev
,
2374 netdev_features_t features
)
2376 struct stmmac_priv
*priv
= netdev_priv(dev
);
2378 if (priv
->plat
->rx_coe
== STMMAC_RX_COE_NONE
)
2379 features
&= ~NETIF_F_RXCSUM
;
2381 if (!priv
->plat
->tx_coe
)
2382 features
&= ~NETIF_F_ALL_CSUM
;
2384 /* Some GMAC devices have a bugged Jumbo frame support that
2385 * needs to have the Tx COE disabled for oversized frames
2386 * (due to limited buffer sizes). In this case we disable
2387 * the TX csum insertionin the TDES and not use SF.
2389 if (priv
->plat
->bugged_jumbo
&& (dev
->mtu
> ETH_DATA_LEN
))
2390 features
&= ~NETIF_F_ALL_CSUM
;
2395 static int stmmac_set_features(struct net_device
*netdev
,
2396 netdev_features_t features
)
2398 struct stmmac_priv
*priv
= netdev_priv(netdev
);
2400 /* Keep the COE Type in case of csum is supporting */
2401 if (features
& NETIF_F_RXCSUM
)
2402 priv
->hw
->rx_csum
= priv
->plat
->rx_coe
;
2404 priv
->hw
->rx_csum
= 0;
2405 /* No check needed because rx_coe has been set before and it will be
2406 * fixed in case of issue.
2408 priv
->hw
->mac
->rx_ipc(priv
->hw
);
2414 * stmmac_interrupt - main ISR
2415 * @irq: interrupt number.
2416 * @dev_id: to pass the net device pointer.
2417 * Description: this is the main driver interrupt service routine.
2419 * o DMA service routine (to manage incoming frame reception and transmission
2421 * o Core interrupts to manage: remote wake-up, management counter, LPI
2424 static irqreturn_t
stmmac_interrupt(int irq
, void *dev_id
)
2426 struct net_device
*dev
= (struct net_device
*)dev_id
;
2427 struct stmmac_priv
*priv
= netdev_priv(dev
);
2430 pm_wakeup_event(priv
->device
, 0);
2432 if (unlikely(!dev
)) {
2433 pr_err("%s: invalid dev pointer\n", __func__
);
2437 /* To handle GMAC own interrupts */
2438 if (priv
->plat
->has_gmac
) {
2439 int status
= priv
->hw
->mac
->host_irq_status(priv
->hw
,
2441 if (unlikely(status
)) {
2442 /* For LPI we need to save the tx status */
2443 if (status
& CORE_IRQ_TX_PATH_IN_LPI_MODE
)
2444 priv
->tx_path_in_lpi_mode
= true;
2445 if (status
& CORE_IRQ_TX_PATH_EXIT_LPI_MODE
)
2446 priv
->tx_path_in_lpi_mode
= false;
2450 /* To handle DMA interrupts */
2451 stmmac_dma_interrupt(priv
);
2456 #ifdef CONFIG_NET_POLL_CONTROLLER
2457 /* Polling receive - used by NETCONSOLE and other diagnostic tools
2458 * to allow network I/O with interrupts disabled.
2460 static void stmmac_poll_controller(struct net_device
*dev
)
2462 disable_irq(dev
->irq
);
2463 stmmac_interrupt(dev
->irq
, dev
);
2464 enable_irq(dev
->irq
);
2469 * stmmac_ioctl - Entry point for the Ioctl
2470 * @dev: Device pointer.
2471 * @rq: An IOCTL specefic structure, that can contain a pointer to
2472 * a proprietary structure used to pass information to the driver.
2473 * @cmd: IOCTL command
2475 * Currently it supports the phy_mii_ioctl(...) and HW time stamping.
2477 static int stmmac_ioctl(struct net_device
*dev
, struct ifreq
*rq
, int cmd
)
2479 struct stmmac_priv
*priv
= netdev_priv(dev
);
2480 int ret
= -EOPNOTSUPP
;
2482 if (!netif_running(dev
))
2491 ret
= phy_mii_ioctl(priv
->phydev
, rq
, cmd
);
2494 ret
= stmmac_hwtstamp_ioctl(dev
, rq
);
2503 #ifdef CONFIG_DEBUG_FS
2504 static struct dentry
*stmmac_fs_dir
;
2505 static struct dentry
*stmmac_rings_status
;
2506 static struct dentry
*stmmac_dma_cap
;
2508 static void sysfs_display_ring(void *head
, int size
, int extend_desc
,
2509 struct seq_file
*seq
)
2512 struct dma_extended_desc
*ep
= (struct dma_extended_desc
*)head
;
2513 struct dma_desc
*p
= (struct dma_desc
*)head
;
2515 for (i
= 0; i
< size
; i
++) {
2519 seq_printf(seq
, "%d [0x%x]: 0x%x 0x%x 0x%x 0x%x\n",
2520 i
, (unsigned int)virt_to_phys(ep
),
2521 (unsigned int)x
, (unsigned int)(x
>> 32),
2522 ep
->basic
.des2
, ep
->basic
.des3
);
2526 seq_printf(seq
, "%d [0x%x]: 0x%x 0x%x 0x%x 0x%x\n",
2527 i
, (unsigned int)virt_to_phys(ep
),
2528 (unsigned int)x
, (unsigned int)(x
>> 32),
2532 seq_printf(seq
, "\n");
2536 static int stmmac_sysfs_ring_read(struct seq_file
*seq
, void *v
)
2538 struct net_device
*dev
= seq
->private;
2539 struct stmmac_priv
*priv
= netdev_priv(dev
);
2540 unsigned int txsize
= priv
->dma_tx_size
;
2541 unsigned int rxsize
= priv
->dma_rx_size
;
2543 if (priv
->extend_desc
) {
2544 seq_printf(seq
, "Extended RX descriptor ring:\n");
2545 sysfs_display_ring((void *)priv
->dma_erx
, rxsize
, 1, seq
);
2546 seq_printf(seq
, "Extended TX descriptor ring:\n");
2547 sysfs_display_ring((void *)priv
->dma_etx
, txsize
, 1, seq
);
2549 seq_printf(seq
, "RX descriptor ring:\n");
2550 sysfs_display_ring((void *)priv
->dma_rx
, rxsize
, 0, seq
);
2551 seq_printf(seq
, "TX descriptor ring:\n");
2552 sysfs_display_ring((void *)priv
->dma_tx
, txsize
, 0, seq
);
2558 static int stmmac_sysfs_ring_open(struct inode
*inode
, struct file
*file
)
2560 return single_open(file
, stmmac_sysfs_ring_read
, inode
->i_private
);
2563 static const struct file_operations stmmac_rings_status_fops
= {
2564 .owner
= THIS_MODULE
,
2565 .open
= stmmac_sysfs_ring_open
,
2567 .llseek
= seq_lseek
,
2568 .release
= single_release
,
2571 static int stmmac_sysfs_dma_cap_read(struct seq_file
*seq
, void *v
)
2573 struct net_device
*dev
= seq
->private;
2574 struct stmmac_priv
*priv
= netdev_priv(dev
);
2576 if (!priv
->hw_cap_support
) {
2577 seq_printf(seq
, "DMA HW features not supported\n");
2581 seq_printf(seq
, "==============================\n");
2582 seq_printf(seq
, "\tDMA HW features\n");
2583 seq_printf(seq
, "==============================\n");
2585 seq_printf(seq
, "\t10/100 Mbps %s\n",
2586 (priv
->dma_cap
.mbps_10_100
) ? "Y" : "N");
2587 seq_printf(seq
, "\t1000 Mbps %s\n",
2588 (priv
->dma_cap
.mbps_1000
) ? "Y" : "N");
2589 seq_printf(seq
, "\tHalf duple %s\n",
2590 (priv
->dma_cap
.half_duplex
) ? "Y" : "N");
2591 seq_printf(seq
, "\tHash Filter: %s\n",
2592 (priv
->dma_cap
.hash_filter
) ? "Y" : "N");
2593 seq_printf(seq
, "\tMultiple MAC address registers: %s\n",
2594 (priv
->dma_cap
.multi_addr
) ? "Y" : "N");
2595 seq_printf(seq
, "\tPCS (TBI/SGMII/RTBI PHY interfatces): %s\n",
2596 (priv
->dma_cap
.pcs
) ? "Y" : "N");
2597 seq_printf(seq
, "\tSMA (MDIO) Interface: %s\n",
2598 (priv
->dma_cap
.sma_mdio
) ? "Y" : "N");
2599 seq_printf(seq
, "\tPMT Remote wake up: %s\n",
2600 (priv
->dma_cap
.pmt_remote_wake_up
) ? "Y" : "N");
2601 seq_printf(seq
, "\tPMT Magic Frame: %s\n",
2602 (priv
->dma_cap
.pmt_magic_frame
) ? "Y" : "N");
2603 seq_printf(seq
, "\tRMON module: %s\n",
2604 (priv
->dma_cap
.rmon
) ? "Y" : "N");
2605 seq_printf(seq
, "\tIEEE 1588-2002 Time Stamp: %s\n",
2606 (priv
->dma_cap
.time_stamp
) ? "Y" : "N");
2607 seq_printf(seq
, "\tIEEE 1588-2008 Advanced Time Stamp:%s\n",
2608 (priv
->dma_cap
.atime_stamp
) ? "Y" : "N");
2609 seq_printf(seq
, "\t802.3az - Energy-Efficient Ethernet (EEE) %s\n",
2610 (priv
->dma_cap
.eee
) ? "Y" : "N");
2611 seq_printf(seq
, "\tAV features: %s\n", (priv
->dma_cap
.av
) ? "Y" : "N");
2612 seq_printf(seq
, "\tChecksum Offload in TX: %s\n",
2613 (priv
->dma_cap
.tx_coe
) ? "Y" : "N");
2614 seq_printf(seq
, "\tIP Checksum Offload (type1) in RX: %s\n",
2615 (priv
->dma_cap
.rx_coe_type1
) ? "Y" : "N");
2616 seq_printf(seq
, "\tIP Checksum Offload (type2) in RX: %s\n",
2617 (priv
->dma_cap
.rx_coe_type2
) ? "Y" : "N");
2618 seq_printf(seq
, "\tRXFIFO > 2048bytes: %s\n",
2619 (priv
->dma_cap
.rxfifo_over_2048
) ? "Y" : "N");
2620 seq_printf(seq
, "\tNumber of Additional RX channel: %d\n",
2621 priv
->dma_cap
.number_rx_channel
);
2622 seq_printf(seq
, "\tNumber of Additional TX channel: %d\n",
2623 priv
->dma_cap
.number_tx_channel
);
2624 seq_printf(seq
, "\tEnhanced descriptors: %s\n",
2625 (priv
->dma_cap
.enh_desc
) ? "Y" : "N");
2630 static int stmmac_sysfs_dma_cap_open(struct inode
*inode
, struct file
*file
)
2632 return single_open(file
, stmmac_sysfs_dma_cap_read
, inode
->i_private
);
2635 static const struct file_operations stmmac_dma_cap_fops
= {
2636 .owner
= THIS_MODULE
,
2637 .open
= stmmac_sysfs_dma_cap_open
,
2639 .llseek
= seq_lseek
,
2640 .release
= single_release
,
2643 static int stmmac_init_fs(struct net_device
*dev
)
2645 /* Create debugfs entries */
2646 stmmac_fs_dir
= debugfs_create_dir(STMMAC_RESOURCE_NAME
, NULL
);
2648 if (!stmmac_fs_dir
|| IS_ERR(stmmac_fs_dir
)) {
2649 pr_err("ERROR %s, debugfs create directory failed\n",
2650 STMMAC_RESOURCE_NAME
);
2655 /* Entry to report DMA RX/TX rings */
2656 stmmac_rings_status
= debugfs_create_file("descriptors_status",
2657 S_IRUGO
, stmmac_fs_dir
, dev
,
2658 &stmmac_rings_status_fops
);
2660 if (!stmmac_rings_status
|| IS_ERR(stmmac_rings_status
)) {
2661 pr_info("ERROR creating stmmac ring debugfs file\n");
2662 debugfs_remove(stmmac_fs_dir
);
2667 /* Entry to report the DMA HW features */
2668 stmmac_dma_cap
= debugfs_create_file("dma_cap", S_IRUGO
, stmmac_fs_dir
,
2669 dev
, &stmmac_dma_cap_fops
);
2671 if (!stmmac_dma_cap
|| IS_ERR(stmmac_dma_cap
)) {
2672 pr_info("ERROR creating stmmac MMC debugfs file\n");
2673 debugfs_remove(stmmac_rings_status
);
2674 debugfs_remove(stmmac_fs_dir
);
2682 static void stmmac_exit_fs(void)
2684 debugfs_remove(stmmac_rings_status
);
2685 debugfs_remove(stmmac_dma_cap
);
2686 debugfs_remove(stmmac_fs_dir
);
2688 #endif /* CONFIG_DEBUG_FS */
2690 static const struct net_device_ops stmmac_netdev_ops
= {
2691 .ndo_open
= stmmac_open
,
2692 .ndo_start_xmit
= stmmac_xmit
,
2693 .ndo_stop
= stmmac_release
,
2694 .ndo_change_mtu
= stmmac_change_mtu
,
2695 .ndo_fix_features
= stmmac_fix_features
,
2696 .ndo_set_features
= stmmac_set_features
,
2697 .ndo_set_rx_mode
= stmmac_set_rx_mode
,
2698 .ndo_tx_timeout
= stmmac_tx_timeout
,
2699 .ndo_do_ioctl
= stmmac_ioctl
,
2700 #ifdef CONFIG_NET_POLL_CONTROLLER
2701 .ndo_poll_controller
= stmmac_poll_controller
,
2703 .ndo_set_mac_address
= eth_mac_addr
,
2707 * stmmac_hw_init - Init the MAC device
2708 * @priv: driver private structure
2709 * Description: this function is to configure the MAC device according to
2710 * some platform parameters or the HW capability register. It prepares the
2711 * driver to use either ring or chain modes and to setup either enhanced or
2712 * normal descriptors.
2714 static int stmmac_hw_init(struct stmmac_priv
*priv
)
2716 struct mac_device_info
*mac
;
2718 /* Identify the MAC HW device */
2719 if (priv
->plat
->has_gmac
) {
2720 priv
->dev
->priv_flags
|= IFF_UNICAST_FLT
;
2721 mac
= dwmac1000_setup(priv
->ioaddr
,
2722 priv
->plat
->multicast_filter_bins
,
2723 priv
->plat
->unicast_filter_entries
);
2725 mac
= dwmac100_setup(priv
->ioaddr
);
2732 /* Get and dump the chip ID */
2733 priv
->synopsys_id
= stmmac_get_synopsys_id(priv
);
2735 /* To use the chained or ring mode */
2737 priv
->hw
->mode
= &chain_mode_ops
;
2738 pr_info(" Chain mode enabled\n");
2739 priv
->mode
= STMMAC_CHAIN_MODE
;
2741 priv
->hw
->mode
= &ring_mode_ops
;
2742 pr_info(" Ring mode enabled\n");
2743 priv
->mode
= STMMAC_RING_MODE
;
2746 /* Get the HW capability (new GMAC newer than 3.50a) */
2747 priv
->hw_cap_support
= stmmac_get_hw_features(priv
);
2748 if (priv
->hw_cap_support
) {
2749 pr_info(" DMA HW capability register supported");
2751 /* We can override some gmac/dma configuration fields: e.g.
2752 * enh_desc, tx_coe (e.g. that are passed through the
2753 * platform) with the values from the HW capability
2754 * register (if supported).
2756 priv
->plat
->enh_desc
= priv
->dma_cap
.enh_desc
;
2757 priv
->plat
->pmt
= priv
->dma_cap
.pmt_remote_wake_up
;
2759 /* TXCOE doesn't work in thresh DMA mode */
2760 if (priv
->plat
->force_thresh_dma_mode
)
2761 priv
->plat
->tx_coe
= 0;
2763 priv
->plat
->tx_coe
= priv
->dma_cap
.tx_coe
;
2765 if (priv
->dma_cap
.rx_coe_type2
)
2766 priv
->plat
->rx_coe
= STMMAC_RX_COE_TYPE2
;
2767 else if (priv
->dma_cap
.rx_coe_type1
)
2768 priv
->plat
->rx_coe
= STMMAC_RX_COE_TYPE1
;
2771 pr_info(" No HW DMA feature register supported");
2773 /* To use alternate (extended) or normal descriptor structures */
2774 stmmac_selec_desc_mode(priv
);
2776 if (priv
->plat
->rx_coe
) {
2777 priv
->hw
->rx_csum
= priv
->plat
->rx_coe
;
2778 pr_info(" RX Checksum Offload Engine supported (type %d)\n",
2779 priv
->plat
->rx_coe
);
2781 if (priv
->plat
->tx_coe
)
2782 pr_info(" TX Checksum insertion supported\n");
2784 if (priv
->plat
->pmt
) {
2785 pr_info(" Wake-Up On Lan supported\n");
2786 device_set_wakeup_capable(priv
->device
, 1);
2794 * @device: device pointer
2795 * @plat_dat: platform data pointer
2796 * @addr: iobase memory address
2797 * Description: this is the main probe function used to
2798 * call the alloc_etherdev, allocate the priv structure.
2800 * on success the new private structure is returned, otherwise the error
2803 struct stmmac_priv
*stmmac_dvr_probe(struct device
*device
,
2804 struct plat_stmmacenet_data
*plat_dat
,
2808 struct net_device
*ndev
= NULL
;
2809 struct stmmac_priv
*priv
;
2811 ndev
= alloc_etherdev(sizeof(struct stmmac_priv
));
2813 return ERR_PTR(-ENOMEM
);
2815 SET_NETDEV_DEV(ndev
, device
);
2817 priv
= netdev_priv(ndev
);
2818 priv
->device
= device
;
2821 stmmac_set_ethtool_ops(ndev
);
2822 priv
->pause
= pause
;
2823 priv
->plat
= plat_dat
;
2824 priv
->ioaddr
= addr
;
2825 priv
->dev
->base_addr
= (unsigned long)addr
;
2827 /* Verify driver arguments */
2828 stmmac_verify_args();
2830 /* Override with kernel parameters if supplied XXX CRS XXX
2831 * this needs to have multiple instances
2833 if ((phyaddr
>= 0) && (phyaddr
<= 31))
2834 priv
->plat
->phy_addr
= phyaddr
;
2836 priv
->stmmac_clk
= devm_clk_get(priv
->device
, STMMAC_RESOURCE_NAME
);
2837 if (IS_ERR(priv
->stmmac_clk
)) {
2838 dev_warn(priv
->device
, "%s: warning: cannot get CSR clock\n",
2840 /* If failed to obtain stmmac_clk and specific clk_csr value
2841 * is NOT passed from the platform, probe fail.
2843 if (!priv
->plat
->clk_csr
) {
2844 ret
= PTR_ERR(priv
->stmmac_clk
);
2847 priv
->stmmac_clk
= NULL
;
2850 clk_prepare_enable(priv
->stmmac_clk
);
2852 priv
->stmmac_rst
= devm_reset_control_get(priv
->device
,
2853 STMMAC_RESOURCE_NAME
);
2854 if (IS_ERR(priv
->stmmac_rst
)) {
2855 if (PTR_ERR(priv
->stmmac_rst
) == -EPROBE_DEFER
) {
2856 ret
= -EPROBE_DEFER
;
2859 dev_info(priv
->device
, "no reset control found\n");
2860 priv
->stmmac_rst
= NULL
;
2862 if (priv
->stmmac_rst
)
2863 reset_control_deassert(priv
->stmmac_rst
);
2865 /* Init MAC and get the capabilities */
2866 ret
= stmmac_hw_init(priv
);
2870 ndev
->netdev_ops
= &stmmac_netdev_ops
;
2872 ndev
->hw_features
= NETIF_F_SG
| NETIF_F_IP_CSUM
| NETIF_F_IPV6_CSUM
|
2874 ndev
->features
|= ndev
->hw_features
| NETIF_F_HIGHDMA
;
2875 ndev
->watchdog_timeo
= msecs_to_jiffies(watchdog
);
2876 #ifdef STMMAC_VLAN_TAG_USED
2877 /* Both mac100 and gmac support receive VLAN tag detection */
2878 ndev
->features
|= NETIF_F_HW_VLAN_CTAG_RX
;
2880 priv
->msg_enable
= netif_msg_init(debug
, default_msg_level
);
2883 priv
->flow_ctrl
= FLOW_AUTO
; /* RX/TX pause on */
2885 /* Rx Watchdog is available in the COREs newer than the 3.40.
2886 * In some case, for example on bugged HW this feature
2887 * has to be disable and this can be done by passing the
2888 * riwt_off field from the platform.
2890 if ((priv
->synopsys_id
>= DWMAC_CORE_3_50
) && (!priv
->plat
->riwt_off
)) {
2892 pr_info(" Enable RX Mitigation via HW Watchdog Timer\n");
2895 netif_napi_add(ndev
, &priv
->napi
, stmmac_poll
, 64);
2897 spin_lock_init(&priv
->lock
);
2898 spin_lock_init(&priv
->tx_lock
);
2900 ret
= register_netdev(ndev
);
2902 pr_err("%s: ERROR %i registering the device\n", __func__
, ret
);
2903 goto error_netdev_register
;
2906 /* If a specific clk_csr value is passed from the platform
2907 * this means that the CSR Clock Range selection cannot be
2908 * changed at run-time and it is fixed. Viceversa the driver'll try to
2909 * set the MDC clock dynamically according to the csr actual
2912 if (!priv
->plat
->clk_csr
)
2913 stmmac_clk_csr_set(priv
);
2915 priv
->clk_csr
= priv
->plat
->clk_csr
;
2917 stmmac_check_pcs_mode(priv
);
2919 if (priv
->pcs
!= STMMAC_PCS_RGMII
&& priv
->pcs
!= STMMAC_PCS_TBI
&&
2920 priv
->pcs
!= STMMAC_PCS_RTBI
) {
2921 /* MDIO bus Registration */
2922 ret
= stmmac_mdio_register(ndev
);
2924 pr_debug("%s: MDIO bus (id: %d) registration failed",
2925 __func__
, priv
->plat
->bus_id
);
2926 goto error_mdio_register
;
2932 error_mdio_register
:
2933 unregister_netdev(ndev
);
2934 error_netdev_register
:
2935 netif_napi_del(&priv
->napi
);
2937 clk_disable_unprepare(priv
->stmmac_clk
);
2941 return ERR_PTR(ret
);
2943 EXPORT_SYMBOL_GPL(stmmac_dvr_probe
);
2947 * @ndev: net device pointer
2948 * Description: this function resets the TX/RX processes, disables the MAC RX/TX
2949 * changes the link status, releases the DMA descriptor rings.
2951 int stmmac_dvr_remove(struct net_device
*ndev
)
2953 struct stmmac_priv
*priv
= netdev_priv(ndev
);
2955 pr_info("%s:\n\tremoving driver", __func__
);
2957 priv
->hw
->dma
->stop_rx(priv
->ioaddr
);
2958 priv
->hw
->dma
->stop_tx(priv
->ioaddr
);
2960 stmmac_set_mac(priv
->ioaddr
, false);
2961 if (priv
->pcs
!= STMMAC_PCS_RGMII
&& priv
->pcs
!= STMMAC_PCS_TBI
&&
2962 priv
->pcs
!= STMMAC_PCS_RTBI
)
2963 stmmac_mdio_unregister(ndev
);
2964 netif_carrier_off(ndev
);
2965 unregister_netdev(ndev
);
2966 if (priv
->stmmac_rst
)
2967 reset_control_assert(priv
->stmmac_rst
);
2968 clk_disable_unprepare(priv
->stmmac_clk
);
2973 EXPORT_SYMBOL_GPL(stmmac_dvr_remove
);
2976 * stmmac_suspend - suspend callback
2977 * @ndev: net device pointer
2978 * Description: this is the function to suspend the device and it is called
2979 * by the platform driver to stop the network queue, release the resources,
2980 * program the PMT register (for WoL), clean and release driver resources.
2982 int stmmac_suspend(struct net_device
*ndev
)
2984 struct stmmac_priv
*priv
= netdev_priv(ndev
);
2985 unsigned long flags
;
2987 if (!ndev
|| !netif_running(ndev
))
2991 phy_stop(priv
->phydev
);
2993 spin_lock_irqsave(&priv
->lock
, flags
);
2995 netif_device_detach(ndev
);
2996 netif_stop_queue(ndev
);
2998 napi_disable(&priv
->napi
);
3000 /* Stop TX/RX DMA */
3001 priv
->hw
->dma
->stop_tx(priv
->ioaddr
);
3002 priv
->hw
->dma
->stop_rx(priv
->ioaddr
);
3004 stmmac_clear_descriptors(priv
);
3006 /* Enable Power down mode by programming the PMT regs */
3007 if (device_may_wakeup(priv
->device
)) {
3008 priv
->hw
->mac
->pmt(priv
->hw
, priv
->wolopts
);
3011 stmmac_set_mac(priv
->ioaddr
, false);
3012 pinctrl_pm_select_sleep_state(priv
->device
);
3013 /* Disable clock in case of PWM is off */
3014 clk_disable(priv
->stmmac_clk
);
3016 spin_unlock_irqrestore(&priv
->lock
, flags
);
3020 priv
->oldduplex
= -1;
3023 EXPORT_SYMBOL_GPL(stmmac_suspend
);
3026 * stmmac_resume - resume callback
3027 * @ndev: net device pointer
3028 * Description: when resume this function is invoked to setup the DMA and CORE
3029 * in a usable state.
3031 int stmmac_resume(struct net_device
*ndev
)
3033 struct stmmac_priv
*priv
= netdev_priv(ndev
);
3034 unsigned long flags
;
3036 if (!netif_running(ndev
))
3039 spin_lock_irqsave(&priv
->lock
, flags
);
3041 /* Power Down bit, into the PM register, is cleared
3042 * automatically as soon as a magic packet or a Wake-up frame
3043 * is received. Anyway, it's better to manually clear
3044 * this bit because it can generate problems while resuming
3045 * from another devices (e.g. serial console).
3047 if (device_may_wakeup(priv
->device
)) {
3048 priv
->hw
->mac
->pmt(priv
->hw
, 0);
3051 pinctrl_pm_select_default_state(priv
->device
);
3052 /* enable the clk prevously disabled */
3053 clk_enable(priv
->stmmac_clk
);
3054 /* reset the phy so that it's ready */
3056 stmmac_mdio_reset(priv
->mii
);
3059 netif_device_attach(ndev
);
3061 init_dma_desc_rings(ndev
, GFP_ATOMIC
);
3062 stmmac_hw_setup(ndev
, false);
3063 stmmac_init_tx_coalesce(priv
);
3065 napi_enable(&priv
->napi
);
3067 netif_start_queue(ndev
);
3069 spin_unlock_irqrestore(&priv
->lock
, flags
);
3072 phy_start(priv
->phydev
);
3076 EXPORT_SYMBOL_GPL(stmmac_resume
);
3079 static int __init
stmmac_cmdline_opt(char *str
)
3085 while ((opt
= strsep(&str
, ",")) != NULL
) {
3086 if (!strncmp(opt
, "debug:", 6)) {
3087 if (kstrtoint(opt
+ 6, 0, &debug
))
3089 } else if (!strncmp(opt
, "phyaddr:", 8)) {
3090 if (kstrtoint(opt
+ 8, 0, &phyaddr
))
3092 } else if (!strncmp(opt
, "dma_txsize:", 11)) {
3093 if (kstrtoint(opt
+ 11, 0, &dma_txsize
))
3095 } else if (!strncmp(opt
, "dma_rxsize:", 11)) {
3096 if (kstrtoint(opt
+ 11, 0, &dma_rxsize
))
3098 } else if (!strncmp(opt
, "buf_sz:", 7)) {
3099 if (kstrtoint(opt
+ 7, 0, &buf_sz
))
3101 } else if (!strncmp(opt
, "tc:", 3)) {
3102 if (kstrtoint(opt
+ 3, 0, &tc
))
3104 } else if (!strncmp(opt
, "watchdog:", 9)) {
3105 if (kstrtoint(opt
+ 9, 0, &watchdog
))
3107 } else if (!strncmp(opt
, "flow_ctrl:", 10)) {
3108 if (kstrtoint(opt
+ 10, 0, &flow_ctrl
))
3110 } else if (!strncmp(opt
, "pause:", 6)) {
3111 if (kstrtoint(opt
+ 6, 0, &pause
))
3113 } else if (!strncmp(opt
, "eee_timer:", 10)) {
3114 if (kstrtoint(opt
+ 10, 0, &eee_timer
))
3116 } else if (!strncmp(opt
, "chain_mode:", 11)) {
3117 if (kstrtoint(opt
+ 11, 0, &chain_mode
))
3124 pr_err("%s: ERROR broken module parameter conversion", __func__
);
3128 __setup("stmmaceth=", stmmac_cmdline_opt
);
3131 MODULE_DESCRIPTION("STMMAC 10/100/1000 Ethernet device driver");
3132 MODULE_AUTHOR("Giuseppe Cavallaro <peppe.cavallaro@st.com>");
3133 MODULE_LICENSE("GPL");