1 /*******************************************************************************
3 Intel(R) Gigabit Ethernet Linux driver
4 Copyright(c) 2007 - 2008 Intel Corporation.
6 This program is free software; you can redistribute it and/or modify it
7 under the terms and conditions of the GNU General Public License,
8 version 2, as published by the Free Software Foundation.
10 This program is distributed in the hope it will be useful, but WITHOUT
11 ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
12 FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
15 You should have received a copy of the GNU General Public License along with
16 this program; if not, write to the Free Software Foundation, Inc.,
17 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA.
19 The full GNU General Public License is included in this distribution in
20 the file called "COPYING".
23 e1000-devel Mailing List <e1000-devel@lists.sourceforge.net>
24 Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497
26 *******************************************************************************/
28 #ifndef _E1000_DEFINES_H_
29 #define _E1000_DEFINES_H_
31 /* Number of Transmit and Receive Descriptors must be a multiple of 8 */
32 #define REQ_TX_DESCRIPTOR_MULTIPLE 8
33 #define REQ_RX_DESCRIPTOR_MULTIPLE 8
35 /* Definitions for power management and wakeup registers */
37 #define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
39 /* Wake Up Filter Control */
40 #define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
41 #define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
42 #define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
43 #define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
44 #define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
45 #define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
46 #define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */
47 #define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */
48 #define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */
49 #define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */
50 #define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */
51 #define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */
52 #define E1000_WUFC_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */
56 /* Wake Up Packet Length */
58 /* Four Flexible Filters are supported */
59 #define E1000_FLEXIBLE_FILTER_COUNT_MAX 4
61 /* Each Flexible Filter is at most 128 (0x80) bytes in length */
62 #define E1000_FLEXIBLE_FILTER_SIZE_MAX 128
65 /* Extended Device Control */
66 #define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */
67 #define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Defineable Pin 4 */
68 #define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Defineable Pin 5 */
69 #define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */
70 #define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */
71 #define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
72 #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
73 #define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
74 #define E1000_CTRL_EXT_LINK_MODE_SGMII 0x00800000
75 #define E1000_CTRL_EXT_EIAME 0x01000000
76 #define E1000_CTRL_EXT_IRCA 0x00000001
77 /* Interrupt delay cancellation */
78 /* Driver loaded bit for FW */
79 #define E1000_CTRL_EXT_DRV_LOAD 0x10000000
80 /* Interrupt acknowledge Auto-mask */
81 /* Clear Interrupt timers after IMS clear */
82 /* packet buffer parity error detection enabled */
83 /* descriptor FIFO parity error detection enable */
84 #define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
85 #define E1000_I2CCMD_REG_ADDR_SHIFT 16
86 #define E1000_I2CCMD_PHY_ADDR_SHIFT 24
87 #define E1000_I2CCMD_OPCODE_READ 0x08000000
88 #define E1000_I2CCMD_OPCODE_WRITE 0x00000000
89 #define E1000_I2CCMD_READY 0x20000000
90 #define E1000_I2CCMD_ERROR 0x80000000
91 #define E1000_MAX_SGMII_PHY_REG_ADDR 255
92 #define E1000_I2CCMD_PHY_TIMEOUT 200
93 #define E1000_IVAR_VALID 0x80
94 #define E1000_GPIE_NSICR 0x00000001
95 #define E1000_GPIE_MSIX_MODE 0x00000010
96 #define E1000_GPIE_EIAME 0x40000000
97 #define E1000_GPIE_PBA 0x80000000
99 /* Receive Descriptor bit definitions */
100 #define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
101 #define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
102 #define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
103 #define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
104 #define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
105 #define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
106 #define E1000_RXD_STAT_DYNINT 0x800 /* Pkt caused INT via DYNINT */
107 #define E1000_RXD_ERR_CE 0x01 /* CRC Error */
108 #define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
109 #define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
110 #define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */
111 #define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
112 #define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
114 #define E1000_RXDEXT_STATERR_CE 0x01000000
115 #define E1000_RXDEXT_STATERR_SE 0x02000000
116 #define E1000_RXDEXT_STATERR_SEQ 0x04000000
117 #define E1000_RXDEXT_STATERR_CXE 0x10000000
118 #define E1000_RXDEXT_STATERR_TCPE 0x20000000
119 #define E1000_RXDEXT_STATERR_IPE 0x40000000
120 #define E1000_RXDEXT_STATERR_RXE 0x80000000
122 /* mask to determine if packets should be dropped due to frame errors */
123 #define E1000_RXD_ERR_FRAME_ERR_MASK ( \
126 E1000_RXD_ERR_SEQ | \
127 E1000_RXD_ERR_CXE | \
130 /* Same mask, but for extended and packet split descriptors */
131 #define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
132 E1000_RXDEXT_STATERR_CE | \
133 E1000_RXDEXT_STATERR_SE | \
134 E1000_RXDEXT_STATERR_SEQ | \
135 E1000_RXDEXT_STATERR_CXE | \
136 E1000_RXDEXT_STATERR_RXE)
138 #define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000
139 #define E1000_MRQC_RSS_FIELD_IPV4 0x00020000
140 #define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000
141 #define E1000_MRQC_RSS_FIELD_IPV6 0x00100000
142 #define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000
145 /* Management Control */
146 #define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
147 #define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
148 #define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
149 /* Enable Neighbor Discovery Filtering */
150 #define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
151 #define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
152 /* Enable MAC address filtering */
153 #define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000
154 /* Enable MNG packets to host memory */
155 #define E1000_MANC_EN_MNG2HOST 0x00200000
156 /* Enable IP address filtering */
159 /* Receive Control */
160 #define E1000_RCTL_EN 0x00000002 /* enable */
161 #define E1000_RCTL_SBP 0x00000004 /* store bad packet */
162 #define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
163 #define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
164 #define E1000_RCTL_LPE 0x00000020 /* long packet enable */
165 #define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
166 #define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
167 #define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
168 #define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */
169 #define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
170 #define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
171 #define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */
172 #define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */
173 #define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */
174 #define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */
175 #define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
176 #define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
177 #define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
180 * Use byte values for the following shift parameters
182 * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
183 * E1000_PSRCTL_BSIZE0_MASK) |
184 * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
185 * E1000_PSRCTL_BSIZE1_MASK) |
186 * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
187 * E1000_PSRCTL_BSIZE2_MASK) |
188 * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
189 * E1000_PSRCTL_BSIZE3_MASK))
190 * where value0 = [128..16256], default=256
191 * value1 = [1024..64512], default=4096
192 * value2 = [0..64512], default=4096
193 * value3 = [0..64512], default=0
196 #define E1000_PSRCTL_BSIZE0_MASK 0x0000007F
197 #define E1000_PSRCTL_BSIZE1_MASK 0x00003F00
198 #define E1000_PSRCTL_BSIZE2_MASK 0x003F0000
199 #define E1000_PSRCTL_BSIZE3_MASK 0x3F000000
201 #define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
202 #define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
203 #define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
204 #define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
206 /* SWFW_SYNC Definitions */
207 #define E1000_SWFW_EEP_SM 0x1
208 #define E1000_SWFW_PHY0_SM 0x2
209 #define E1000_SWFW_PHY1_SM 0x4
211 /* FACTPS Definitions */
213 #define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
214 #define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
215 #define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
216 #define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
217 #define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
218 #define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
219 #define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
220 #define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
221 #define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
222 #define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
223 #define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
224 /* Defined polarity of Dock/Undock indication in SDP[0] */
225 /* Reset both PHY ports, through PHYRST_N pin */
226 /* enable link status from external LINK_0 and LINK_1 pins */
227 #define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
228 #define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
229 #define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */
230 #define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */
231 #define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
232 #define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */
233 #define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */
234 #define E1000_CTRL_RST 0x04000000 /* Global reset */
235 #define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
236 #define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
237 #define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
238 #define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
239 /* Initiate an interrupt to manageability engine */
240 #define E1000_CTRL_I2C_ENA 0x02000000 /* I2C enable */
242 /* Bit definitions for the Management Data IO (MDIO) and Management Data
243 * Clock (MDC) pins in the Device Control Register.
246 #define E1000_CONNSW_ENRGSRC 0x4
247 #define E1000_PCS_CFG_PCS_EN 8
248 #define E1000_PCS_LCTL_FLV_LINK_UP 1
249 #define E1000_PCS_LCTL_FSV_100 2
250 #define E1000_PCS_LCTL_FSV_1000 4
251 #define E1000_PCS_LCTL_FDV_FULL 8
252 #define E1000_PCS_LCTL_FSD 0x10
253 #define E1000_PCS_LCTL_FORCE_LINK 0x20
254 #define E1000_PCS_LCTL_FORCE_FCTRL 0x80
255 #define E1000_PCS_LCTL_AN_ENABLE 0x10000
256 #define E1000_PCS_LCTL_AN_RESTART 0x20000
257 #define E1000_PCS_LCTL_AN_TIMEOUT 0x40000
258 #define E1000_ENABLE_SERDES_LOOPBACK 0x0410
260 #define E1000_PCS_LSTS_LINK_OK 1
261 #define E1000_PCS_LSTS_SPEED_100 2
262 #define E1000_PCS_LSTS_SPEED_1000 4
263 #define E1000_PCS_LSTS_DUPLEX_FULL 8
264 #define E1000_PCS_LSTS_SYNK_OK 0x10
267 #define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
268 #define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
269 #define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
270 #define E1000_STATUS_FUNC_SHIFT 2
271 #define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
272 #define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
273 #define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
274 #define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
275 /* Change in Dock/Undock state. Clear on write '0'. */
276 /* Status of Master requests. */
277 #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000
278 /* BMC external code execution disabled */
280 /* Constants used to intrepret the masked PCI-X bus speed. */
283 #define SPEED_100 100
284 #define SPEED_1000 1000
285 #define HALF_DUPLEX 1
286 #define FULL_DUPLEX 2
289 #define ADVERTISE_10_HALF 0x0001
290 #define ADVERTISE_10_FULL 0x0002
291 #define ADVERTISE_100_HALF 0x0004
292 #define ADVERTISE_100_FULL 0x0008
293 #define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */
294 #define ADVERTISE_1000_FULL 0x0020
296 /* 1000/H is not supported, nor spec-compliant. */
297 #define E1000_ALL_SPEED_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
298 ADVERTISE_100_HALF | ADVERTISE_100_FULL | \
300 #define E1000_ALL_NOT_GIG (ADVERTISE_10_HALF | ADVERTISE_10_FULL | \
301 ADVERTISE_100_HALF | ADVERTISE_100_FULL)
302 #define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL)
303 #define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL)
304 #define E1000_ALL_FULL_DUPLEX (ADVERTISE_10_FULL | ADVERTISE_100_FULL | \
306 #define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF)
308 #define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX
311 #define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
312 #define E1000_LEDCTL_LED0_MODE_SHIFT 0
313 #define E1000_LEDCTL_LED0_IVRT 0x00000040
314 #define E1000_LEDCTL_LED0_BLINK 0x00000080
316 #define E1000_LEDCTL_MODE_LED_ON 0xE
317 #define E1000_LEDCTL_MODE_LED_OFF 0xF
319 /* Transmit Descriptor bit definitions */
320 #define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
321 #define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
322 #define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
323 #define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
324 #define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
325 #define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
326 #define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
327 /* Extended desc bits for Linksec and timesync */
329 /* Transmit Control */
330 #define E1000_TCTL_EN 0x00000002 /* enable tx */
331 #define E1000_TCTL_PSP 0x00000008 /* pad short packets */
332 #define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
333 #define E1000_TCTL_COLD 0x003ff000 /* collision distance */
334 #define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
336 /* Transmit Arbitration Count */
339 #define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
341 /* Receive Checksum Control */
342 #define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
343 #define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */
344 #define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
346 /* Header split receive */
347 #define E1000_RFCTL_LEF 0x00040000
349 /* Collision related configuration parameters */
350 #define E1000_COLLISION_THRESHOLD 15
351 #define E1000_CT_SHIFT 4
352 #define E1000_COLLISION_DISTANCE 63
353 #define E1000_COLD_SHIFT 12
355 /* Ethertype field values */
356 #define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */
358 #define MAX_JUMBO_FRAME_SIZE 0x3F00
360 /* Extended Configuration Control and Size */
361 #define E1000_PHY_CTRL_GBE_DISABLE 0x00000040
364 #define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */
365 #define E1000_PBA_24K 0x0018
366 #define E1000_PBA_34K 0x0022
367 #define E1000_PBA_64K 0x0040 /* 64KB */
373 #define MIN_NUM_XMITS 1000
375 /* SW Semaphore Register */
376 #define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
377 #define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
379 /* Interrupt Cause Read */
380 #define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
381 #define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */
382 #define E1000_ICR_LSC 0x00000004 /* Link Status Change */
383 #define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */
384 #define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */
385 #define E1000_ICR_RXO 0x00000040 /* rx overrun */
386 #define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */
387 #define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */
388 #define E1000_ICR_RXCFG 0x00000400 /* Rx /c/ ordered set */
389 #define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */
390 #define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */
391 #define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */
392 #define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */
393 #define E1000_ICR_TXD_LOW 0x00008000
394 #define E1000_ICR_SRPD 0x00010000
395 #define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */
396 #define E1000_ICR_MNG 0x00040000 /* Manageability event */
397 #define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */
398 /* If this bit asserted, the driver should claim the interrupt */
399 #define E1000_ICR_INT_ASSERTED 0x80000000
400 /* queue 0 Rx descriptor FIFO parity error */
401 #define E1000_ICR_RXD_FIFO_PAR0 0x00100000
402 /* queue 0 Tx descriptor FIFO parity error */
403 #define E1000_ICR_TXD_FIFO_PAR0 0x00200000
404 /* host arb read buffer parity error */
405 #define E1000_ICR_HOST_ARB_PAR 0x00400000
406 #define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */
407 /* queue 1 Rx descriptor FIFO parity error */
408 #define E1000_ICR_RXD_FIFO_PAR1 0x01000000
409 /* queue 1 Tx descriptor FIFO parity error */
410 #define E1000_ICR_TXD_FIFO_PAR1 0x02000000
411 /* FW changed the status of DISSW bit in the FWSM */
412 #define E1000_ICR_DSW 0x00000020
413 /* LAN connected device generates an interrupt */
414 #define E1000_ICR_PHYINT 0x00001000
415 #define E1000_ICR_EPRST 0x00100000 /* ME handware reset occurs */
417 /* Extended Interrupt Cause Read */
418 #define E1000_EICR_RX_QUEUE0 0x00000001 /* Rx Queue 0 Interrupt */
419 #define E1000_EICR_RX_QUEUE1 0x00000002 /* Rx Queue 1 Interrupt */
420 #define E1000_EICR_RX_QUEUE2 0x00000004 /* Rx Queue 2 Interrupt */
421 #define E1000_EICR_RX_QUEUE3 0x00000008 /* Rx Queue 3 Interrupt */
422 #define E1000_EICR_TX_QUEUE0 0x00000100 /* Tx Queue 0 Interrupt */
423 #define E1000_EICR_TX_QUEUE1 0x00000200 /* Tx Queue 1 Interrupt */
424 #define E1000_EICR_TX_QUEUE2 0x00000400 /* Tx Queue 2 Interrupt */
425 #define E1000_EICR_TX_QUEUE3 0x00000800 /* Tx Queue 3 Interrupt */
426 #define E1000_EICR_TCP_TIMER 0x40000000 /* TCP Timer */
427 #define E1000_EICR_OTHER 0x80000000 /* Interrupt Cause Active */
431 * This defines the bits that are set in the Interrupt Mask
432 * Set/Read Register. Each bit is documented below:
433 * o RXT0 = Receiver Timer Interrupt (ring 0)
434 * o TXDW = Transmit Descriptor Written Back
435 * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
436 * o RXSEQ = Receive Sequence Error
437 * o LSC = Link Status Change
439 #define IMS_ENABLE_MASK ( \
446 /* Interrupt Mask Set */
447 #define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
448 #define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
449 #define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */
450 #define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
451 #define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */
453 /* Extended Interrupt Mask Set */
454 #define E1000_EIMS_TCP_TIMER E1000_EICR_TCP_TIMER /* TCP Timer */
455 #define E1000_EIMS_OTHER E1000_EICR_OTHER /* Interrupt Cause Active */
457 /* Interrupt Cause Set */
458 #define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
459 #define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */
461 /* Extended Interrupt Cause Set */
463 /* Transmit Descriptor Control */
464 /* Enable the counting of descriptors still to be processed. */
466 /* Flow Control Constants */
467 #define FLOW_CONTROL_ADDRESS_LOW 0x00C28001
468 #define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
469 #define FLOW_CONTROL_TYPE 0x8808
471 /* 802.1q VLAN Packet Size */
472 #define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMA'd) */
473 #define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
475 /* Receive Address */
477 * Number of high/low register pairs in the RAR. The RAR (Receive Address
478 * Registers) holds the directed and multicast addresses that we monitor.
479 * Technically, we have 16 spots. However, we reserve one of these spots
480 * (RAR[15]) for our directed address used by controllers with
481 * manageability enabled, allowing us room for 15 multicast addresses.
483 #define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
486 #define E1000_ERR_NVM 1
487 #define E1000_ERR_PHY 2
488 #define E1000_ERR_CONFIG 3
489 #define E1000_ERR_PARAM 4
490 #define E1000_ERR_MAC_INIT 5
491 #define E1000_ERR_RESET 9
492 #define E1000_ERR_MASTER_REQUESTS_PENDING 10
493 #define E1000_ERR_HOST_INTERFACE_COMMAND 11
494 #define E1000_BLK_PHY_RESET 12
495 #define E1000_ERR_SWFW_SYNC 13
496 #define E1000_NOT_IMPLEMENTED 14
498 /* Loop limit on how long we wait for auto-negotiation to complete */
499 #define COPPER_LINK_UP_LIMIT 10
500 #define PHY_AUTO_NEG_LIMIT 45
501 #define PHY_FORCE_LIMIT 20
502 /* Number of 100 microseconds we wait for PCI Express master disable */
503 #define MASTER_DISABLE_TIMEOUT 800
504 /* Number of milliseconds we wait for PHY configuration done after MAC reset */
505 #define PHY_CFG_TIMEOUT 100
506 /* Number of 2 milliseconds we wait for acquiring MDIO ownership. */
507 /* Number of milliseconds for NVM auto read done after MAC reset. */
508 #define AUTO_READ_DONE_TIMEOUT 10
511 #define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
513 /* Transmit Configuration Word */
514 #define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */
516 /* Receive Configuration Word */
518 /* PCI Express Control */
519 #define E1000_GCR_RXD_NO_SNOOP 0x00000001
520 #define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002
521 #define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004
522 #define E1000_GCR_TXD_NO_SNOOP 0x00000008
523 #define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010
524 #define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020
526 #define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \
527 E1000_GCR_RXDSCW_NO_SNOOP | \
528 E1000_GCR_RXDSCR_NO_SNOOP | \
529 E1000_GCR_TXD_NO_SNOOP | \
530 E1000_GCR_TXDSCW_NO_SNOOP | \
531 E1000_GCR_TXDSCR_NO_SNOOP)
533 /* PHY Control Register */
534 #define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */
535 #define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */
536 #define MII_CR_POWER_DOWN 0x0800 /* Power down */
537 #define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */
538 #define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */
539 #define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */
540 #define MII_CR_SPEED_1000 0x0040
541 #define MII_CR_SPEED_100 0x2000
542 #define MII_CR_SPEED_10 0x0000
544 /* PHY Status Register */
545 #define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */
546 #define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */
548 /* Autoneg Advertisement Register */
549 #define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */
550 #define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */
551 #define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */
552 #define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */
553 #define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */
554 #define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */
556 /* Link Partner Ability Register (Base Page) */
557 #define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */
558 #define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */
560 /* Autoneg Expansion Register */
562 /* 1000BASE-T Control Register */
563 #define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */
564 #define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */
565 #define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */
566 /* 0=Configure PHY as Slave */
567 #define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */
568 /* 0=Automatic Master/Slave config */
570 /* 1000BASE-T Status Register */
571 #define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */
572 #define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */
575 /* PHY 1000 MII Register/Bit Definitions */
576 /* PHY Registers defined by IEEE */
577 #define PHY_CONTROL 0x00 /* Control Register */
578 #define PHY_STATUS 0x01 /* Status Register */
579 #define PHY_ID1 0x02 /* Phy Id Reg (word 1) */
580 #define PHY_ID2 0x03 /* Phy Id Reg (word 2) */
581 #define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */
582 #define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */
583 #define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */
584 #define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */
587 #define E1000_EECD_SK 0x00000001 /* NVM Clock */
588 #define E1000_EECD_CS 0x00000002 /* NVM Chip Select */
589 #define E1000_EECD_DI 0x00000004 /* NVM Data In */
590 #define E1000_EECD_DO 0x00000008 /* NVM Data Out */
591 #define E1000_EECD_REQ 0x00000040 /* NVM Access Request */
592 #define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */
593 #define E1000_EECD_PRES 0x00000100 /* NVM Present */
594 /* NVM Addressing bits based on type 0=small, 1=large */
595 #define E1000_EECD_ADDR_BITS 0x00000400
596 #define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */
597 #define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */
598 #define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */
599 #define E1000_EECD_SIZE_EX_SHIFT 11
601 /* Offset to data in NVM read/write registers */
602 #define E1000_NVM_RW_REG_DATA 16
603 #define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
604 #define E1000_NVM_RW_REG_START 1 /* Start operation */
605 #define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
606 #define E1000_NVM_POLL_READ 0 /* Flag for polling for read complete */
608 /* NVM Word Offsets */
609 #define NVM_ID_LED_SETTINGS 0x0004
610 /* For SERDES output amplitude adjustment. */
611 #define NVM_INIT_CONTROL2_REG 0x000F
612 #define NVM_INIT_CONTROL3_PORT_A 0x0024
613 #define NVM_ALT_MAC_ADDR_PTR 0x0037
614 #define NVM_CHECKSUM_REG 0x003F
616 #define E1000_NVM_CFG_DONE_PORT_0 0x40000 /* MNG config cycle done */
617 #define E1000_NVM_CFG_DONE_PORT_1 0x80000 /* ...for second port */
619 /* Mask bits for fields in Word 0x0f of the NVM */
620 #define NVM_WORD0F_PAUSE_MASK 0x3000
621 #define NVM_WORD0F_ASM_DIR 0x2000
623 /* Mask bits for fields in Word 0x1a of the NVM */
625 /* For checksumming, the sum of all words in the NVM should equal 0xBABA. */
626 #define NVM_SUM 0xBABA
628 #define NVM_PBA_OFFSET_0 8
629 #define NVM_PBA_OFFSET_1 9
630 #define NVM_WORD_SIZE_BASE_SHIFT 6
632 /* NVM Commands - Microwire */
634 /* NVM Commands - SPI */
635 #define NVM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
636 #define NVM_WRITE_OPCODE_SPI 0x02 /* NVM write opcode */
637 #define NVM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
638 #define NVM_WREN_OPCODE_SPI 0x06 /* NVM set Write Enable latch */
639 #define NVM_RDSR_OPCODE_SPI 0x05 /* NVM read Status register */
641 /* SPI NVM Status Register */
642 #define NVM_STATUS_RDY_SPI 0x01
644 /* Word definitions for ID LED Settings */
645 #define ID_LED_RESERVED_0000 0x0000
646 #define ID_LED_RESERVED_FFFF 0xFFFF
647 #define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
648 (ID_LED_OFF1_OFF2 << 8) | \
649 (ID_LED_DEF1_DEF2 << 4) | \
651 #define ID_LED_DEF1_DEF2 0x1
652 #define ID_LED_DEF1_ON2 0x2
653 #define ID_LED_DEF1_OFF2 0x3
654 #define ID_LED_ON1_DEF2 0x4
655 #define ID_LED_ON1_ON2 0x5
656 #define ID_LED_ON1_OFF2 0x6
657 #define ID_LED_OFF1_DEF2 0x7
658 #define ID_LED_OFF1_ON2 0x8
659 #define ID_LED_OFF1_OFF2 0x9
661 #define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF
662 #define IGP_ACTIVITY_LED_ENABLE 0x0300
663 #define IGP_LED3_MODE 0x07000000
665 /* PCI/PCI-X/PCI-EX Config space */
666 #define PCI_HEADER_TYPE_REGISTER 0x0E
667 #define PCIE_LINK_STATUS 0x12
669 #define PCI_HEADER_TYPE_MULTIFUNC 0x80
670 #define PCIE_LINK_WIDTH_MASK 0x3F0
671 #define PCIE_LINK_WIDTH_SHIFT 4
673 #define PHY_REVISION_MASK 0xFFFFFFF0
674 #define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
675 #define MAX_PHY_MULTI_PAGE_REG 0xF
677 /* Bit definitions for valid PHY IDs. */
682 #define M88E1111_I_PHY_ID 0x01410CC0
683 #define IGP03E1000_E_PHY_ID 0x02A80390
684 #define M88_VENDOR 0x0141
686 /* M88E1000 Specific Registers */
687 #define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
688 #define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
689 #define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
691 #define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
692 #define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
694 /* M88E1000 PHY Specific Control Register */
695 #define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
696 /* 1=CLK125 low, 0=CLK125 toggling */
697 #define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
698 /* Manual MDI configuration */
699 #define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
700 /* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */
701 #define M88E1000_PSCR_AUTO_X_1000T 0x0040
702 /* Auto crossover enabled all speeds */
703 #define M88E1000_PSCR_AUTO_X_MODE 0x0060
705 * 1=Enable Extended 10BASE-T distance (Lower 10BASE-T Rx Threshold
706 * 0=Normal 10BASE-T Rx Threshold
708 /* 1=5-bit interface in 100BASE-TX, 0=MII interface in 100BASE-TX */
709 #define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
711 /* M88E1000 PHY Specific Status Register */
712 #define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
713 #define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */
714 #define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
722 #define M88E1000_PSSR_CABLE_LENGTH 0x0380
723 #define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
724 #define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
726 #define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
728 /* M88E1000 Extended PHY Specific Control Register */
730 * 1 = Lost lock detect enabled.
731 * Will assert lost lock and bring
732 * link down if idle not seen
733 * within 1ms in 1000BASE-T
736 * Number of times we will attempt to autonegotiate before downshifting if we
739 #define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
740 #define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000
742 * Number of times we will attempt to autonegotiate before downshifting if we
745 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300
746 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100
747 #define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
749 /* M88EC018 Rev 2 specific DownShift settings */
750 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
751 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800
754 #define E1000_MDIC_REG_SHIFT 16
755 #define E1000_MDIC_PHY_SHIFT 21
756 #define E1000_MDIC_OP_WRITE 0x04000000
757 #define E1000_MDIC_OP_READ 0x08000000
758 #define E1000_MDIC_READY 0x10000000
759 #define E1000_MDIC_ERROR 0x40000000
762 #define E1000_GEN_CTL_READY 0x80000000
763 #define E1000_GEN_CTL_ADDRESS_SHIFT 8
764 #define E1000_GEN_POLL_TIMEOUT 640
This page took 0.046365 seconds and 6 git commands to generate.
projects / deliverable / linux.git / blob